Freescale Semiconductor Errata Document Number: MC13892ER Rev. 10.0, 4/2012 MC13892, Silicon Errata Introduction Device Revision Identification This errata sheet applies to the following devices: Table 1. Silicon Revision Package Part Number Silicon Revision MC13892VK Part Marking MC13892 2.0A MC13892JVK MC13892AJVK 139-PIN 7x7mm BGA MC13892BJVK DB00M29X MC13892J 3.1 3.2 (1) MC13892CJVK MC13892DJVK 3.5 MC13892VL MC13892AJ DB01M29X MC13892BJ DB03M29X MC13892CJ DB05M29X MC13892DJ DA03N57D MC13892VL 2.0A MC13892JVL MC13892AJVL 186-PIN 12x12mm BGA MC13892BJVL DB00M29X MC13892JVL 3.1 3.2 (1) MC13892CJVL MC13892DJVL Die ID 3.5 MC13892AJVL DB01M29X MC13892BJVL DB03M29X MC13892CJVL DB05M29X MC13892DJVL DA03N57D Notes 1. Silicon revision 3.2 does not have a part marking difference. The revision is indicated with date code 1040 or greater. Device Build Information / Date Code Device markings indicate build information containing the week and year of manufacture. The date is coded with the last four characters of the nine character build information code (e.g. "CTKAH0429"). The date is coded as four numerical digits where the first two digits indicate the year and the last two digits indicate the week. For instance, the date code "0429" indicates the 29th week of the year 2004. Device Part Number Prefixes Some device samples are marked with a PC prefix. A PC prefix indicates a prototype device which has undergone basic testing only. After full characterization and qualification, devices will be marked with the MC prefix. General Description This errata document applies to MC13892 data sheet. (c) Freescale Semiconductor, Inc., 2010-2012. All rights reserved. Table 2. Definitions of Errata Severity Errata Type Meaning High Failure mode that severely inhibits the use of the device for all or a majority of intended applications. Medium Failure mode that might restrict or limit the use of the device for all or a majority of intended applications. Low Unexpected behavior that does not cause significant problems for the intended applications of the device. Enhancement Improvement made to the device due to previously found issues on the design. Table 3. High Severity Issues Erratum ID 8374 8568 8612 Erratum System Impact Description RTC: Loss on the crystal oscillator upon power up The switch of the 32 kHz clock system from crystal to internal clock causes missing pulses in the 32 kHz clock, which lowers the frequency of the switcher PLL. The buck regulator then drops in output voltage. Workaround: Place a 10 MOhm resistor in parallel with the crystal. Power: If UVBUS is present before the battery, then an overshoot on the output of the switching regulators occurs If UVBUS is present before the battery, the switcher acts as soon as the battery is present, instead of waiting until the power up sequence is initialized.This overshoot can tie the switcher output to BP for a short period. Workaround: Place a 100 kOhm pull-down resistor on VCORE. Charger: Reverse supply mode shuts off The reverse supply mode shuts off when the temperature is above 90C. Fix/Plan Status: Fixed in silicon in revision 3.1 Note: This workaround is only needed if the UVBUS supply is present before the battery. It is not needed if UVBUS is not used. Fix/Plan Status: Fixed in silicon in revision 3.1 Workaround: Do not use reverse supply mode if the device is being used at this temperature. Fix/Plan Status: Fixed in silicon in revision 3.1 8690 Buck Regulators: Buck current limit does not function The buck current limit does not function properly, there is no max current limit, and current limit may engage before the rated load current of the buck regulator. Workaround: Immediately after power up firmware should disable the current limit by setting the SWILIMB SPI bit = 1. Application needs to provide current limit protection circuitry either in the battery or as a pre regulated supply to BP. Fix/Plan Status: None 8691, 8692 Boost Regulator: Serial LED Boost system interfering with REFCORE voltage Activating the SWLED boost regulator can cause REFCORE perturbations which cause the part to shutdown. Workaround: Do not use SWLED boost supply to provide power for backlight LED sinks. Use external supply to generate boost voltage required for backlight LEDs. Fix/Plan Status: None MC13892ER 2 Freescale Semiconductor Table 3. High Severity Issues Erratum ID Erratum 8870 Charger: BP over-voltage when hot plugging a high voltage charger When hot plugging a high voltage charger, the BP node can spike greater than 7.5 V. Charger: Failure of charger removal detection Charger removal may not always be detected by the PMIC. This causes the charge path to stay on and the battery voltage to be present at charger input. Which could cause the charge LED to be illuminated if present in the application. 8938 System Impact Description Workaround: Use an over-voltage protection IC on the charger input Fix/Plan Status: None Workaround: Use software to poll the charger current via an ADC reading every one second, to check if the charger is detected. Disable it when the charge current goes below a reading of 3, or is negative. MC13892 Charger LED Driver patch for the i.MX35PDK is posted to: http://www.freescale.com/webapp/sps/site/ prod_summary.jsp?code=IMX35PDK&fpsp =1&tab=Design_Tools_Tab Detailed Description of Software * When a charger is detected, CHRGDETI = 1 and CHRGDETS = 1, software needs to poll the charge current ADC every one second. * Check the value of the "Charger Current (CHRGISNS-BPSNS)" by writing a 1 on CHRGICON (Reg#43, bit#1) and writing a 4 on ADA1 (Reg#44, Bits 5-7). * Take eight readings from the ADC for the charger current, discard the largest and smallest values, and average the remaining six. * Take this average and DISABLE THE CHARGER if the reading is "<= 3", or "NEGATIVE". All negative readings have the last bit set to 1. * To disable the charger, set ICHRG[3:0] = 0000 and set the CHGAUTOVIB = 1. * Wait 1000 ms. * Re-enable the charger by setting CHGAUTOVIB = 0. * If the average is > 3, then continue polling the charger current every 1 second. * If CHGDETI = 1 and CHGDETS =0, polling every one second should not take place. Fix/Plan Status: Fixed in silicon in revision 3.5 MC13892ER Freescale Semiconductor 3 Table 4. Medium Severity Issues Erratum ID 8372 Erratum Power: REGSCPEN behavior does not match the spec. System Impact Description The LDO SCPI does not work as per spec. The interrupt SCPI is generated when a short-circuit is detected, even if the REGSPEN bit is not set (the spec says that in this case the interrupt should not fire). Workaround: Recommendation is to have a short circuit protection enabled by setting the REGSCPEN bit. However, if it is desired to disable REGSCPEN, when SCPI interrupt occurs follow the below steps to identify the interrupt source: a) If backlight is enabled, Read both LED Control 0 and LED Control 1 registers i. If both are equal to 0x), then SCPI indicates interrupt from the backlight LED drivers. ii. If both are not equal to 0x0, then SCPI indicates short circuit protection of a regulator b) If backlight is disabled, SCPI indicates short circuit protection of a regulator. Fix/Plan Status: Fixed in silicon in revision 3.1 When the BP is in POWER OFF state, the Standby Workaround: None leakage currents on the BPSNS and CHRGISNS pins are ~ 35 A. If UVBUS is connected to Fix/Plan Status: CHRGRAW, there is an additional 35 A of Fixed in silicon in revision 3.1 leakage current. 8375 Charger: BP to CHRGRAW leakage. 8382 USB: UVBUS The USB attach turn on event only works if the turn on event ramp of UVBUS from 0 to 4.4 V is <50 ms. works only if the ramp is < 50 ms. Workaround: (3 options are available): 1. Speed up the UVBUS turn on time. 2. Work with a common USB and charger path. A turn on event will occur when USB is plugged in. 3. Use any other turn on event to power up. Fix/Plan Status: Fixed in silicon in revision 3.1 MC13892ER 4 Freescale Semiconductor Table 4. Medium Severity Issues Erratum ID Erratum Charger: Operation from wall charger with no battery via the charge path 8732 Buck Regulator: Buck current limit interaction with DVS 8982 Description When using the battery charger as the only source Workaround: of power, as in a battery-less application or if the * Add a 120mS RC delay on battery is deeply discharged, the following precautions should be observed: RESETBMCU. 1. It is still necessary to connect ADIN5 to either * Add a 68K pull-up resistor to the I/O rail or if the battery VCOREDIG or a midpoint of a divider from GPIO1 at the RESETBMCU output. to ground since the battery charger will still is deeply * Add a 100 Ohm resistor from the interpret this voltage as the battery pack thermistor discharged. RESETBMCU output of the PMIC to the by default. processors reset input. 2. Very careful budgeting of the total current * Add a 2.2uF capacitor to ground on the consumption and voltage standoff from processor side of the 100 Ohm resistor. CHRGRAW to BPSNS must be made, since the * Repeat the above steps for RESETB. power limiter is operational by default, and a battery less or if the battery is deeply discharged system won't have a source of current if the power Fix/Plan Status: Fixed in silicon in revision 3.2 dissipation limit is reached. 3. If operating from a USB host the unit load limit (100 mA max.) must still be observed. 4. If operating from a "wall charger", and if there is no battery or if the battery is deeply discharged, there is an period of approximately 85 ms after RESETB is released, that the current limit is set to 80mA before setting the current limit is set to a nominal 560 mA. If the total current demand is greater than this limit, or if the battery is deeply discharged, the voltage may collapse and RESETB may pulse a few times (depending in part in the system load and dependence on RESETB.) Therefore, at the end of this time, RESETB may or may not be active. It may be necessary to use one of the other turn-on events (such as PWRONx) to turn the 13892 back on. 8719 8945 System Impact The buck current limit can be reached if an output voltage increase is requested on a buck regulator while close to max load. The consequence is that the programmed output voltage is not reached, during the DVS ramp up phase, the coil current increases temporarily to permit an output rise, and can reach current limit. Workaround: When ramping buck regulator voltage from a lower to a higher set point near max load, disable current limit by setting the SWILIMB SPI bit = 1. Fix/Plan Status: None ADC: Erroneous Erroneous readings occur on the die temperature ADC Reading and the CHRGRAW ADC channels when the IC fails to detect the removal of the charger (see Errata 8938). Workaround: None USB: Leakage increases when VINUSB goes above 5.1 V Workaround: None When the VINUSB voltage exceeds 5.1 V, excess current flows into the USB node. Fix/Plan Status: Fixed in silicon in revision 3.5 Fix/Plan Status: Fixed in silicon in revision 3.5 MC13892ER Freescale Semiconductor 5 Table 4. Medium Severity Issues Erratum ID 8939 Erratum System Impact Description Charger: When measuring the current from the battery, Incorrect battery there is an offset of ~30 mA to 50 mA from the current actual value. measurement Workaround: Calibrate the ADC offset during production. Calculate the average slope and add the offset to the battery current. Fix/Plan Status: None 8940 Charger: Incorrect charger voltage measurement When measuring the voltage from the attached charger, there is an offset from the actual value. Workaround: Calibrate the ADC offset during production. Calculate the average slope and add the offset to the battery voltage. Fix/Plan Status: None Table 5. Low Severity Issues Erratum ID 8373 Erratum System Impact Description Coin Cell: When the coin cell is present and the Leakage current battery is disconnected, a leakage on the LICELL. current around 2.0 to 3.0 A with BP=high-impedance and 2mA if BP is actively pulled to ground can be observed from BP to GND, and also a leakage voltage of 0.3 to 0.49 V. This leakage current comes from the coin cell. Workaround: Add NMOS switch or load switch between BP and VINAUDIO with source connected to BP and the drain connected to the VINAUDIO. Enable the switch when application is ON and disable when OFF. Fix/Plan Status: Fixed in silicon in revision 3.1 7640 Workaround: If LEDs cannot handle 10% higher Lighting Signaling LED and backlight LED System: LED currents are higher than target value by ~ current, then program the current sinks to one level below the required setting. currents are 10% higher than spec Fix/Plan Status: Fixed in silicon in revision 3.1 8718 Control Logic: If any of the PWRONx pins are grounded, neither of the other 2 PWRON pins are PWRONx pin grounded not able to generate a turn on event. able to power on IC with other PWRONx pin Workaround: Set the PWRONxDBNC bits (or at least the ones for the offending PWRON pin) to nonzero. Fix/Plan Status: None 8849 Charger: Charger path reverse current threshold is too high Charger path reverse current threshold is Workaround: None too high. Threshold is ~ 120 to180 mA, where it should be 35 mA. This only Fix/Plan Status: impacts reverse supply mode from the None battery to an external accessory via the charge path. 8944 ADC: Code spike on the ADC 1 out of 33 k readings can have a positive Workaround: Take a minimum of 8 readings on ADC or negative code spike channels and remove the max and min. values, then take the average of these readings. Fix/Plan Status: None MC13892ER 6 Freescale Semiconductor Table 5. Low Severity Issues Erratum ID 8969 Erratum System Impact Description Charger: End of When the CYCLB is set, the end of charge detection charge is not detected. failure Workaround: The CYCLB bit must be cleared for correct End of Charge detection. Fix/Plan Status: None 8970 Additional ~110uA drawn from the battery Workaround: Backlight intermittently 1. From 100% duty cycle go to an intermediate Drivers: Changing duty duty cycle before going to 0% duty cycle. cycle of 2. Set LEDxxRAMP = 1 while transitioning backlight LED from100% to 0% duty cycle. current sinks 3. Don't use 100% duty cycle setting. Use 96.8% (LEDMD, (31/32) setting instead, for example. LEDAD, LEDKP) from 100% to 0% results in Fix/Plan Status: additional None ~110uA being drawn from the battery intermittently MC13892ER Freescale Semiconductor 7 REVISION HISTORY REVISION DATE DESCRIPTION OF CHANGES 4.0 2/2010 * Initial Release 5.0 5/2010 * Errata updated to add MC qualified part numbers to Silicon Revision 6.0 10/2010 * Added errata 8870, 8873, and 8849 * Removed errata 8682 and 7874 7.0 10/2010 * Removed paragraph describing the device revision identification, since it did not apply to part marking 8.0 11/2011 * Added MC13892CJVK and MC13892CJVL part numbers for P3.5 Silicon Revision * Added errata 8938, 8945, 8982, 8939, 8940, 8944, and 8969 9.0 3/2012 * Added erratum 8970 10.0 4/2012 * Added MC13892DJVK and MC13892DJVL part numbers to Silicon Revision MC13892ER 8 Freescale Semiconductor How to Reach Us: Information in this document is provided solely to enable system and software Home Page: freescale.com implementers to use Freescale products. There are no express or implied copyright Web Support: freescale.com/support information in this document. licenses granted hereunder to design or fabricate any integrated circuits on the Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: http://www.reg.net/v2/webservices/Freescale/Docs/TermsandConditions.htm Freescale, the Freescale logo, AltiVec, C-5, CodeTest, CodeWarrior, ColdFire, C-Ware, Energy Efficient Solutions logo, mobileGT, PowerQUICC, QorIQ, Qorivva, StarCore, and Symphony are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Airfast, BeeKit, BeeStack, ColdFire+, CoreNet, Flexis, MagniV, MXC, Platform in a Package, Processor expert, QorIQ Qonverge, QUICC Engine, Ready Play, SMARTMOS, TurboLink, Vybrid, and Xtrinsic are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) 2012 Freescale Semiconductor, Inc. Document Number: MC13892ER Rev. 10.0 4/2012