LM2705 LM2705 Micropower Step-up DC/DC Converter with 150mA Peak Current Limit Literature Number: SNVS191D LM2705 Micropower Step-up DC/DC Converter with 150mA Peak Current Limit General Description Features The LM2705 is a micropower step-up DC/DC in a small 5-lead SOT-23 package. A current limited, fixed off-time control scheme conserves operating current resulting in high efficiency over a wide range of load conditions. The 21V switch allows for output voltages as high as 20V. The low 400ns offtime permits the use of tiny, low profile inductors and capacitors to minimize footprint and cost in space-conscious portable applications. The LM2705 is ideal for LCD panels requiring low current and high efficiency as well as white LED applications for cellular phone back-lighting. The LM2705 can drive up to 3 white LEDs from a single Li-Ion battery. The low peak inductor current of the LM2705 makes it ideal for USB applications. 150mA, 0.7, internal switch Uses small surface mount components Adjustable output voltage up to 20V 2.2V to 7V input range Input undervoltage lockout 0.01A shutdown current Small 5-Lead SOT-23 package Applications LCD Bias Supplies White LED Back-Lighting Handheld Devices Digital Cameras Portable Applications Typical Application Circuit 20039701 FIGURE 1. Typical 20V Application (c) 2010 National Semiconductor Corporation 200397 www.national.com LM2705 Micropower Step-up DC/DC Converter with 150mA Peak Current Limit June 17, 2010 LM2705 Connection Diagram Top View 20039702 SOT23-5 TJmax = 125C, JA = 220C/W (Note 2) Ordering Information Order Number Package Type NSC Package Drawing Top Mark LM2705MF-ADJ SOT23-5 MA05B S59B 1000 Units, Tape and Reel Supplied As LM2705MFX-ADJ SOT23-5 MA05B S59B 3000 Units, Tape and Reel Pin Descriptions/Functions Pin Name 1 SW 2 GND 3 FB 4 SHDN 5 VIN Function Power Switch input. Ground. Output voltage feedback input. Shutdown control input, active low. Analog and Power input. SW(Pin 1): Switch Pin. This is the drain of the internal NMOS power switch. Minimize the metal trace area connected to this pin to minimize EMI. GND(Pin 2): Ground Pin. Tie directly to ground plane. FB(Pin 3): Feedback Pin. Set the output voltage by selecting values for R1 and R2 using: www.national.com Connect the ground of the feedback network to an AGND plane which should be tied directly to the GND pin. SHDN(Pin 4): Shutdown Pin. The shutdown pin is an active low control. Tie this pin above 1.1V to enable the device. Tie this pin below 0.3V to turn off the device. VIN(Pin 5): Input Supply Pin. Bypass this pin with a capacitor as close to the device as possible. 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN SW Voltage FB Voltage SHDN Voltage Maximum Junction Temp. TJ (Note 2) Lead Temperature (Soldering 10 sec.) 7.5V 21V 2V 7.5V 150C 215C 220C 2kV 200V Operating Conditions Junction Temperature (Note 5) Supply Voltage SW Voltage Max. 300C -40C to +125C 2.2V to 7V 20.5V Electrical Characteristics Specifications in standard type face are for TJ = 25C and those in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C). Unless otherwise specified VIN =2.2V. Symbol IQ Parameter Device Disabled Device Enabled Shutdown VFB FeedbackTrip Point ICL Switch Current Limit IB FB Pin Bias Current VIN Input Voltage Range RDSON Switch RDSON TOFF Switch Off Time ISD SHDN Pin Current Conditions Min (Note 5) Typ (Note 6) Max (Note 5) Units 40 235 0.01 70 300 2.5 A 1.189 1.237 1.269 V 100 150 180 mA 30 120 nA FB = 1.3V FB = 1.2V SHDN = 0V FB = 1.23V (Note 7) 2.2 0.7 7.0 V 1.6 400 SHDN = VIN, TJ = 25C 0 SHDN = VIN, TJ = 125C 15 SHDN = GND 0 ns 80 nA IL Switch Leakage Current VSW = 20V 0.05 UVP Input Undervoltage Lockout ON/OFF Threshold 1.8 V VFB Hysteresis Feedback Hysteresis 8 mV SHDN Threshold SHDN low 0.7 SHDN High 1.1 JA SOT23-5 Thermal Resistance 0.7 220 5 0.3 A V C/W Note 1: Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) - TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 4: ESD susceptibility using the machine model is 150V for SW pin. Note 5: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% production tested or guaranteed through statistical analysis. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 6: Typical numbers are at 25C and represent the most likely norm. Note 7: Feedback current flows into the pin. 3 www.national.com LM2705 Vapor Phase (60 sec.) Infrared (15 sec.) ESD Ratings (Note 3) Human Body Model Machine Model (Note 4) Absolute Maximum Ratings (Note 1) LM2705 Typical Performance Characteristics Enable Current vs VIN (Part Switching) Disable Current vs VIN (Part Not Switching) 20039705 20039706 Efficiency vs Load Current Efficiency vs Load Current 20039725 20039724 SHDN Threshold vs VIN Switch Current Limit vs VIN 20039713 www.national.com 20039737 4 FB Trip Point and FB Pin Current vs Temperature 20039715 20039723 Output Voltage vs Load Current Off Time vs Temperature 20039741 20039727 Step Response Start-Up/Shutdown 20039728 VOUT = 20V, VIN = 3.0V 1) Load, 0.5mA to 5mA to 0.5mA, DC 2) VOUT, 200mV/div, AC 3) IL, 100mA/div, DC T = 100s/div 20039729 VOUT = 20V, VIN = 3.0V 1) SHDN, 1V/div, DC 2) IL, 100mA/div, DC 3) VOUT, 10V/div, DC T = 400s/div RL = 3.9k 5 www.national.com LM2705 Switch RDSON vs VIN LM2705 Operation 20039704 FIGURE 2. LM2705 Block Diagram 20039730 VOUT = 20V, VIN = 2.7V, IOUT = 2.5mA 1) VSW, 20V/div, DC 2) Inductor Current, 100mA/div, DC 3) VOUT, 200mV/div, AC T = 10s/div FIGURE 3. Typical Switching Waveform www.national.com 6 INDUCTOR SELECTION - SEPIC REGULATOR The following equation can be used to calculate the approximate inductor value for a SEPIC regulator: The boost inductor, L1, can be smaller or larger but is generally chosen to be the same value as L2. See Figure 9and Figure 10 for typical SEPIC applications. DIODE SELECTION To maintain high efficiency, the average current rating of the schottky diode should be larger than the peak inductor current, IPK. Schottky diodes with a low forward drop and fast switching speeds are ideal for increasing efficiency in portable applications. Choose a reverse breakdown of the schottky diode larger than the output voltage. Application Information CAPACITOR SELECTION Choose low ESR capacitors for the output to minimize output voltage ripple. Multilayer ceramic capacitors are the best choice. For most applications, a 1F ceramic capacitor is sufficient. For some applications a reduction in output voltage ripple can be achieved by increasing the output capacitor. Output voltage ripple can further be reduced by adding a 4.7pF feed-forward capacitor in the feedback network placed in parallel with RF1, see Figure 2. Local bypassing for the input is needed on the LM2705. Multilayer ceramic capacitors are a good choice for this as well. A 4.7F capacitor is sufficient for most applications. For additional bypassing, a 100nF ceramic capacitor can be used to shunt high frequency ripple on the input. INDUCTOR SELECTION - BOOST REGULATOR The appropriate inductor for a given application is calculated using the following equation: where VD is the schottky diode voltage, ICL is the switch current limit found in the Typical Performance Characteristics section, and TOFF is the switch off time. When using this equation be sure to use the minimum input voltage for the application, such as for battery powered applications. For the LM2705 constant-off time control scheme, the NMOS power switch is turned off when the current limit is reached. There is approximately a 100ns delay from the time the current limit is reached in the NMOS power switch and when the internal logic actually turns off the switch. During this 100ns delay, the peak inductor current will increase. This increase in inductor current demands a larger saturation current rating for the inductor. This saturation current can be approximated by the following equation: LAYOUT CONSIDERATIONS The input bypass capacitor CIN, as shown in Figure 1, must be placed close to the IC. This will reduce copper trace resistance which effects input voltage ripple of the IC. For additional input voltage filtering, a 100nF bypass capacitor can be placed in parallel with CIN to shunt any high frequency noise to ground. The output capacitor, COUT, should also be placed close to the IC. Any copper trace connections for the Cout capacitor can increase the series resistance, which directly effects output voltage ripple. The feedback network, resistors R1 and R2, should be kept close to the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to an analog ground plane. The analog ground plane should tie directly to the GND pin. If no analog ground plane is available, the ground connection for the feedback network should tie directly to the GND pin. Trace connections made to the inductor and schottky diode Choosing inductors with low ESR decrease power losses and increase efficiency. Care should be taken when choosing an inductor. For applications that require an input voltage that approaches the output voltage, such as when converting a Li-Ion battery voltage to 5V, the 400ns off time may not be enough time to 7 www.national.com LM2705 discharge the energy in the inductor and transfer the energy to the output capacitor and load. This can cause a ramping effect in the inductor current waveform and an increased ripple on the output voltage. Using a smaller inductor will cause the IPK to increase and will increase the output voltage ripple further. For typical curves and evaluation purposes the DT1608C series inductors from Coilcraft were used. Other acceptable inductors would include, but are not limited to, the SLF6020T series from TDK, the NP05D series from Taiyo Yuden, the CDRH4D18 series from Sumida, and the P1166 series from Pulse. The LM2705 features a constant off-time control scheme. Operation can be best understood by referring to Figure 2 and Figure 3. Transistors Q1 and Q2 and resistors R3 and R4 of Figure 2 form a bandgap reference used to control the output voltage. When the voltage at the FB pin is less than 1.237V, the Enable Comp in Figure 2 enables the device and the NMOS switch is turned on pulling the SW pin to ground. When the NMOS switch is on, current begins to flow through inductor L while the load current is supplied by the output capacitor COUT. Once the current in the inductor reaches the current limit, the CL Comp trips and the 400ns One Shot turns off the NMOS switch.The SW voltage will then rise to the output voltage plus a diode drop and the inductor current will begin to decrease as shown in Figure 3. During this time the energy stored in the inductor is transferred to COUT and the load. After the 400ns off-time the NMOS switch is turned on and energy is stored in the inductor again. This energy transfer from the inductor to the output causes a stepping effect in the output ripple as shown in Figure 3. This cycle is continued until the voltage at FB reaches 1.237V. When FB reaches this voltage, the enable comparator then disables the device turning off the NMOS switch and reducing the Iq of the device to 40uA. The load current is then supplied solely by COUT indicated by the gradually decreasing slope at the output as shown in Figure 3. When the FB pin drops slightly below 1.237V, the enable comparator enables the device and begins the cycle described previously. The SHDN pin can be used to turn off the LM2705 and reduce the Iq to 0.01A. In shutdown mode the output voltage will be a diode drop lower than the input voltage. LM2705 should be minimized to reduce power dissipation and increase overall efficiency. Copt / Ropt included Copt / Ropt excluded 20039749 20039750 FIGURE 4. Output Ripple Voltage 20039742 20039709 FIGURE 5. 2 White LED Application and Efficiency www.national.com 8 LM2705 20039743 20039734 FIGURE 6. 3 White LED Application and Efficiency 20039735 FIGURE 7. Li-Ion 12V Application 9 www.national.com LM2705 20039736 FIGURE 8. 5V to 12V Application 20039739 FIGURE 9. 3.3V SEPIC Application www.national.com 10 LM2705 20039740 FIGURE 10. 5V SEPIC Application 11 www.national.com LM2705 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead Small Outline Package (M5) For Ordering, Refer to Ordering Information Table NS Package Number MA05B www.national.com 12 LM2705 Notes 13 www.national.com LM2705 Micropower Step-up DC/DC Converter with 150mA Peak Current Limit Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated