MXL1016IS8 - Hytronics - Datasheet.Directory

General Description

The Maxim MXL1016 (10ns, typ) high-speed, comple-

mentary-output comparator is designed specifically to

interface directly to TTL logic while operating from

either a dual ±5V supply or a single +5V supply.

The MXL1016 remains stable with the outputs in the

active region, which greatly reduces output instabillity

common with slow-moving input signals. In addition, an

output latch (LE) is provided.

For lower-power, higher-performance comparators, see

the MAX912/MAX913 dual/single comparators data

sheet. The MAX913 is an improved plug-in replacement

for the MXL1016 and the MAX912 is the dual equivalent

to the MAX913.

Applications

High-Speed A/D Converters

Zero-Crossing Detectors

Current Sense for Switching Regulators

High-Speed Sampling Circuits

High-Speed Triggers

Line Receivers

Extended Range V/F Converters

Fast Pulse Height/Width Discriminators

Features

♦Ultra Fast (10ns, typ)

♦Single +5V or Dual ±5V Supply Operation

♦Complementary TTL Outputs

♦Low Offset Voltage: 1mV

♦No Minimum Input Slew-Rate Requirement

♦No Power-Supply Current Spiking

♦Output Latch

MXL1016

Ultra-Fast Precision TTL Comparator

________________________________________________________________ Maxim Integrated Products 1

Ordering Information

19-0138; Rev 3; 8/03

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

PART TEMP RANGE PIN-PACKAGE

MXL1016CN8 0°C to +70°C 8 Plastic DIP

MXL1016CS8 0°C to +70°C 8 SO

GND

LEV-

7 QOUTIN+

IN-

V+

DIP/SO

TOP VIEW

MXL1016 QOUT

Pin Configuration

PIN NAME FUNCTION

1 V+ Positive Power Supply +5V

2 IN+ Noninverting Input

3 IN- Inverting Input

4V-

Negative Power Supply, -5V for dual supply

or GND for single supply

5LE

Latch Enable. QOUT and QOUT are

latched when LE is high

6 GND Ground

7 QOUT TTL Output

8QOUT Complementary TTL Output

Pin Description

MXL1016

Ultra-Fast Precision TTL Comparator

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(V+ = 5V, V- = -5V, VOUT(Q) = 1.4V, VLE = 0V, TA= TMIN to TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Positive Supply Voltage............................................................7V

Negative Supply Voltage ........................................................-7V

V+ to V- ..................................................................................13V

Differential Input Voltage

MXL1016............................................................................±5V

Input Voltage (either input)

MXL1016 ......................................................Equal to Supplies

Latch Pin Voltage .............................................Equal to Supplies

Output Current (continuous).............................................±20mA

Continuous Power Dissipation (TA= +70°C)

8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW

8-Pin SO (derate 5.88mW/°C above +70°C)................471mW

Operating Temperature Ranges:

MXL1016.............................................................0°C to +70°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

TA = +25°C 1.0 ±3

Input Offset Voltage (Note 2) VOS RS ≤ 100Ω

TA = TMIN to TMAX 3.5 mV

Input Offset-Voltage Drift ∆VOS/∆TT

A = TMIN to TMAX 4 µV/°C

TA = +25°C 0.3 1

Input Offset Current (Note 2) IOS TA = TMIN to TMAX 1.3 µA

TA = +25°C510

Input Bias Current (Note 3) IBTA = TMIN to TMAX 13 µA

Dual +5V and -5V supply -3.75 +3.50

Input Voltage Range VCM Single 5V supply +1.25 +3.50 V

Common-Mode Rejection Ratio CMRR -3.75V ≤ VCM ≤ 3.5V 80 96 dB

Positive supply: 4.6V ≤ V+ ≤ 5.4V 60 75

Power-Supply Rejection Ratio PSRR Negative supply: -2V ≥ V- ≥ -7V 80 100 dB

Small-Signal Voltage Gain AV1V ≤ VOUT ≤ 2V, TA = +25°C 1400 3000 V/V

IOUT = 1mA 2.7 3.4

Output High Voltage VOH V+ ≥ 4.6V IOUT = 10mA 2.4 3.0 V

ISINK = 4mA 0.3 0.5

Output Low Voltage VOL ISINK = 10mA, TA = +25°C 0.4 V

Positive Supply Current I+ (Note 4) 25 35 mA

Negative Supply Current I- (Note 4) 3 5 mA

MXL1016

Ultra-Fast Precision TTL Comparator

_______________________________________________________________________________________ 3

ELECTRICAL CHARACTERISTICS (continued)

(V+ = 5V, V- = -5V, VOUT(Q) = 1.4V, VLE = 0V, TA= TMIN to TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Latch Pin High Input Voltage VIH 2.0 V

Latch Pin Low Input Voltage VIL 0.8 V

Latch Pin Current IIL VLE = 0V -500 µA

TA = +25°C1014

∆VIN = 100mV,

OD = 5mV 16

TA = +25°C912

Propagation Delay (Note 5) tPD ∆VIN = 100mV,

OD = 20mV 15

Differential Propagation Delay

(Note 5) ∆tPD ∆VIN = 100mV, OD = 5mV, TA = +25°C4ns

Latch Setup Time tSU (Note 6) 2 ns

Latch Hold Time tH(Note 6) 2 ns

Note 1: All specifications are 100% tested at TA= +25°C, unless otherwise noted. Specification limits over temperature (TA= TMIN

to TMAX) are guaranteed by design.

Note 2: Input offset voltage is defined as the average of the two input offset voltages, measured by forcing first one output, then the

other to 1.4V. Input offset current is defined in the same way.

Note 3: Input bias current (IB) is defined as the average of the two input currents.

Note 4: Supply currents are measured with VOUT (Q) driven to both VOH and VOL (not 1.4V).

Note 5: tPD and ∆tPD cannot be measured in automatic handling equipment with low values of overdrive. Characterization and

correlation tests have shown that tPD and ∆tPD limits can be guaranteed by design. Electrical Characteristic DC tests are

performed to guarantee that all internal bias conditions are correct. For low overdrive conditions, VOS is added to overdrive.

Note 6: Input latch setup time, tSU, is the interval in which the input signal must be stable prior to asserting the latch signal. The hold

time, tH, is the interval after the latch is asserted in which the input signal must be stable.

Package Information

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,

go to www.maxim-ic.com/packages.)

MXL1016

Ultra-Fast Precision TTL Comparator

4 _______________________________________________________________________________________

PDIPN.EPS

MXL1016

Ultra-Fast Precision TTL Comparator

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are

implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 5

Package Information (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,

go to www.maxim-ic.com/packages.)

SOICN .EPS

PACKAGE OUTLINE, .150" SOIC

21-0041 B

REV.DOCUMENT CONTROL NO.APPROVAL

PROPRIETARY INFORMATION

TITLE:

TOP VIEW

FRONT VIEW

MAX

0.010

0.069

0.019

0.157

0.010

INCHES

0.150

0.007

DIM

0.014

0.004

MIN

0.053A

0.19

3.80 4.00

0.25

MILLIMETERS

0.10

0.35

1.35

MIN

0.49

0.25

MAX

1.75

0.050

0.016L0.40 1.27

0.3940.386D

MINDIM

INCHES

MAX

9.80 10.00

MILLIMETERS

MIN MAX

16 AC

0.337 0.344 AB8.758.55 14

0.189 0.197 AA5.004.80 8

N MS012

SIDE VIEW

H 0.2440.228 5.80 6.20

e 0.050 BSC 1.27 BSC

eBA1

0-8

VARIATIONS:

ENGLISH • ???? • ??? • ???

WHAT'S NEW

PRODUCTS

SOLUTIONS

DESIGN

APPNOTES

SUPPORT

BUY

COMPANY

MEMBERS

MXL1016

Part Number Table

Notes:

See the MXL1016 QuickView Data Sheet for further information on this product family or download the

MXL1016 full data sheet (PDF, 152kB).

Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.2.

Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within

one business day.

Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See

full data sheet or Part Naming Conventions.

* Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the

product uses.

Part Number

Free

Sample

Buy

Direct

Package:

TYPE PINS SIZE

DRAWING CODE/VAR *

Temp

RoHS/Lead-Free?

Materials Analysis

MXL1016MJ8

-55C to +125C

RoHS/Lead-Free: No

MXL1016IS8

-20C to +85C

RoHS/Lead-Free: No

MXL1016IS8-T

-20C to +85C

RoHS/Lead-Free: No

MXL1016C N8

PDIP;8 pin;.300"

Dwg: 21-0043D (PDF)

Use pkgcode/variation: P8-1*

0C to +70C

RoHS/Lead-Free: No

Materials Analysis

MXL1016IN8

-20C to +85C

RoHS/Lead-Free: No

MXL1016C S8

SOIC;8 pin;.150"

Dwg: 21-0041B (PDF)

Use pkgcode/variation: S8-2*

-40C to +85C

RoHS/Lead-Free: No

Materials Analysis

MXL1016C S8-T

SOIC;8 pin;.150"

Dwg: 21-0041B (PDF)

Use pkgcode/variation: S8-2*

-40C to +85C

RoHS/Lead-Free: No

Materials Analysis

MXL1016C S8+

SOIC;8 pin;.150"

Dwg: 21-0041B (PDF)

Use pkgcode/variation: S8+2*

-40C to +85C

RoHS/Lead-Free: Yes

Materials Analysis

MXL1016C S8+T

SOIC;8 pin;.150"

Dwg: 21-0041B (PDF)

Use pkgcode/variation: S8+2*

-40C to +85C

RoHS/Lead-Free: Yes

Materials Analysis

Didn't Find What You Need?

C opyright 200 7 by M axim I ntegrated P roducts, Dallas Semiconduc tor • Legal Notices • Privacy P olicy