LM140H-12/883 - NATIONAL SEMICONDUCTOR

LM140QML

LM140QML Three Terminal Positive Regulators

Literature Number: SNVS382A

April 3, 2008

LM140QML

Three Terminal Positive Regulators

General Description

The monolithic 3-terminal positive voltage regulators employ

internal current-limiting, thermal shutdown and safe-area

compensation, making them essentially indestructible. If ad-

equate heat sinking is provided, they can deliver over 0.5A

output current. They are intended as fixed voltage regulators

in a wide range of applications including local (on-card) reg-

ulation for elimination of noise and distribution problems as-

sociated with single-point regulation. In addition to use as

fixed voltage regulators, these devices can be used with ex-

ternal components to obtain adjustable output voltages and

currents.

Considerable effort was expended to make the entire series

of regulators easy to use and minimize the number of external

components. It is not necessary to bypass the output, al-

though this does improve transient response. Input bypassing

is needed only if the regulator is located far from the filter ca-

pacitor of the power supply.

Features

■Complete specifications at 1.0A and 0.5A loads

■No external components

■Internal thermal overload protection

■Internal short circuit current-limiting

■Output transistor safe-area compensation

Ordering Information

NS Part Number SMD Part Number NS Package Number Package Description

LM140H-5.0/883 H03A 3LD TO-39 Metal Can

LM140H-12/883 H03A 3LD TO-39 Metal Can

LM140H-15/883 H03A 3LD TO-39 Metal Can

LM140K-5.0/883 K02C 2LD TO-3 Metal Can

LM140K-12/883 K02C 2LD TO-3 Metal Can

LM140K-15/883 K02C 2LD TO-3 Metal Can

Connection Diagrams

Steel Metal Can TO-39 Package (H)

20155401

Bottom View

See NS Package Number H03A

TO-3 Metal Can (K)

20155402

Bottom View

See NS Package Number K02C

LM140QML Three Terminal Positive Regulators

Absolute Maximum Ratings (Note 1)

DC Input Voltage 35V

Internal Power Dissipation (Note 2) Internally Limited

Maximum Junction Temperature (TJmax) 150°C

Storage Temperature Range -65°C ≤ TA ≤ +150°C

Operating Temperature Range -55°C ≤ TA ≤ +125°C

Lead Temperature (Soldering 10 seconds) 300°C

Thermal Resistance

θJA

T0−39 (Still Air) 232°C/W

T0−39 (500 LF/Min Air Flow) 77°C/W

T0−3 (Still Air) 35°C/W

T0−3 (500 LF/Min Air Flow) TBD

θJC

T0−39 15°C/W

T0−3 4°C/W

ESD Susceptibility (Note 3) 2KV

Quality Conformance Inspection

MIL-Std-883, Method 5005 - Group A

Subgroup Description Temp °C

1 Static tests at +25

2 Static tests at +125

3 Static tests at -55

4 Dynamic tests at +25

5 Dynamic tests at +125

6 Dynamic tests at -55

7 Functional tests at +25

8A Functional tests at +125

8B Functional tests at -55

9 Switching tests at +25

10 Switching tests at +125

11 Switching tests at -55

12 Settling time at +25

13 Settling time at +125

14 Settling time at -55

www.national.com 2

LM140QML

LM140H–5.0 Electrical Characteristics

DC Parameters

The following conditions apply, unless otherwise specified.

DC: VI = 10V, IL =350mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

VOOutput Voltage VI = 35V, IL = 5mA 4.75 5.75 V 1

4.80 5.20 V 1

VI = 8V 4.70 5.30 V 1, 2, 3

VI = 8V, IL = 5mA 4.70 5.30 V 1, 2, 3

VI = 20V, IL = 5mA 4.70 5.30 V 1, 2, 3

VI = 20V 4.70 5.30 V 1, 2, 3

RLine Line Regulation 7V ≤ VI ≤ 25V, IL = 200mA -50 50 mV 1

8V ≤ VI ≤ 25V, IL = 200mA -50 50 mV 2, 3

8V ≤ VI ≤ 20V, IL = 200mA -25 25 mV 1

-40 40 mV 2, 3

RLoad Load Regulation 5mA ≤ IL ≤ 500mA -50 50 mV 1

-100 100 mV 2, 3

5mA ≤ IL ≤ 200mA -25 25 mV 1

-50 50 mV 2, 3

IQQuiescent Current 7.0 mA 1, 2, 3

ΔIQQuiescent Current Change 8V ≤ VI ≤ 25V, IL = 200mA -0.8 0.8 mA 1, 2, 3

5mA ≤ IL ≤ 350mA -0.5 0.5 mA 1, 2, 3

IPk Peak Current VI - VO = 7V (Note 4) 0.4 2.0 A 1, 2, 3

VDO Dropout Voltage (Note 5) 2.5 V 1

IOS Short Circuit Current VI = 35V 1.0 A 1, 2, 3

AC Parameters

The following conditions apply, unless otherwise specified.

AC: VI = 10V, IL =350mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

RR Ripple Rejection IL = 125mA, eI = 1VRMS,

ƒ = 2.4KHz, VI = 10V

62 dB 4, 5, 6

3 www.national.com

LM140QML

LM140H–12 Electrical Characteristics

DC Parameters

The following conditions apply, unless otherwise specified.

DC: VI = 19V, IL =350mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

VOOutput Voltage VI = 35V, IL = 5mA 11.4 12.6 V 1

11.5 12.5 V 1

VI = 15.5V 11.4 12.6 V 1, 2, 3

VI = 15.5V, IL = 5mA 11.4 12.6 V 1, 2, 3

VI = 27V, IL = 5mA 11.4 12.6 V 1, 2, 3

VI = 27V 11.4 12.6 V 1, 2, 3

RLine Line Regulation 14.5V ≤ VI ≤ 30V, IL = 200mA -60 60 mV 1

15.0V ≤ VI ≤ 30V, IL = 200mA -120 120 mV 2, 3

16V ≤ VI ≤ 25V, IL = 200mA -30 30 mV 1

-60 60 mV 2, 3

RLoad Load Regulation 5mA ≤ IL ≤ 500mA -120 120 mV 1

-240 240 mV 2, 3

5mA ≤ IL ≤ 200mA -60 60 mV 1

-120 120 mV 2, 3

IQQuiescent Current 7.0 mA 1, 2, 3

ΔIQQuiescent Current Change 14.5V ≤ VI ≤ 30V, IL = 200mA -0.8 0.8 mA 1, 2, 3

5mA ≤ IL ≤ 350mA -0.5 0.5 mA 1, 2, 3

IPk Peak Current VI - VO = 7V (Note 4) 0.4 2.0 A 1, 2, 3

VDO Dropout Voltage (Note 5) 2.5 V 1

IOS Short Circuit Current VI = 35V 1.0 A 1, 2, 3

AC Parameters

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

RR Ripple Rejection VI = 17V, IL = 125mA,

eI = 1VRMS, ƒ = 2.4KHz

55 dB 4, 5, 6

www.national.com 4

LM140QML

LM140H–15 Electrical Characteristics

DC Parameters

The following conditions apply, unless otherwise specified.

DC: VI = 23V, IL =350mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

VOOutput Voltage VI = 35V, IL = 5mA 14.25 15.75 V 1

14.40 15.60 V 1

VI = 18.5V 14.25 15.75 V 1, 2, 3

VI = 18.5V, IL = 5mA 14.25 15.75 V 1, 2, 3

VI = 30V, IL = 5mA 14.25 15.75 V 1, 2, 3

VI = 30V 14.25 15.75 V 1, 2, 3

RLine Line Regulation 17.5V ≤ VI ≤ 30V, IL = 200mA -60 60 mV 1

18.5V ≤ VI ≤ 30V, IL = 200mA -120 120 mV 2, 3

20V ≤ VI ≤ 30V, IL = 200mA -30 30 mV 1

-60 60 mV 2, 3

RLoad Load Regulation 5mA ≤ IL ≤ 500mA -150 150 mV 1

-300 300 mV 2, 3

5mA ≤ IL ≤ 200mA -75 75 mV 1

-150 150 mV 2, 3

IQQuiescent Current 7.0 mA 1, 2, 3

ΔIQQuiescent Current Change 17.5V ≤ VI ≤ 30V, IL = 200mA -0.8 0.8 mA 1, 2, 3

5mA ≤ IL ≤ 350mA -0.5 0.5 mA 1, 2, 3

IPk Peak Current VI - VO = 7V (Note 4) 0.4 2.0 A 1, 2, 3

VDO Dropout Voltage (Note 5) 2.5 V 1

IOS Short Circuit Current VI = 35V 1.0 A 1, 2, 3

AC Parameters

The following conditions apply, unless otherwise specified.

AC: VI = 23V, IL =350mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

RR Ripple Rejection VI=20V, IL=125mA,

eI=1VRMS, ƒ = 2.4KHz

54 dB 4, 5, 6

5 www.national.com

LM140QML

LM140K–5.0 Electrical Characteristics

DC Parameters

The following conditions apply, unless otherwise specified.

DC: VI = 10V, IL = 5mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

IQQuiescent Current IL = 1A 6.0 mA 1

7.0 mA 2, 3

ΔQQuiescent Current Change IL = 1A, 8V ≤ VI ≤ 20mA -0.8 0.8 mA 1

IL ≤ 500mA, 8V ≤ VI ≤ 25V -0.8 0.8 mA 1, 2, 3

5mA, ≤ IL ≤ 1.0A -0.5 0.5 mA 1, 2, 3

VOOutput Voltage 4.80 5.20 V 1

VI = 8V 4.75 5.25 V 1, 2, 3

VI = 8V, IL = 1A 4.75 5.25 V 1, 2, 3

VI = 20V 4.75 5.25 V 1, 2, 3

VI = 20V, IL = 1A 4.75 5.25 V 1, 2, 3

RLine Line Regulation IL = 500mA, 7V ≤ VI ≤ 25V -50 50 mV 1, 2, 3

IL = 1A, 7.3V ≤ VI ≤ 20V -50 50 mV 1

IL = 1A, 8.0V ≤ VI ≤ 20V -50 50 mV 2, 3

IL = 1A, 8V ≤ VI ≤ 12V -25 25 mV 1, 2, 3

RLoad Load Regulation 5mA ≤ IL ≤ 1.5A -50 50 mV 1

5mA ≤ IL ≤ 1.0A -50 50 mV 2, 3

250mA ≤ IL ≤ 750mA -25 25 mV 1

IOS Current Limit -4.0 -0.02 A 1

VI = 35V -2.0 -0.02 A 1

AC Parameters

The following conditions apply, unless otherwise specified.

AC: VI = 10V, IL = 5mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

RR Ripple Rejection ƒ = 120Hz, IL = 350mA,

eI = 1VRMS

68 dB 4

www.national.com 6

LM140QML

LM140K–12 Electrical Characteristics

DC Parameters

The following conditions apply, unless otherwise specified.

DC: VI = 19V, IL = 5mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

IQQuiescent Current IL = 1A 6.0 mA 1

7.0 mA 2, 3

ΔIQQuiescent Current Change IL = 1A, 15.5V ≤ VI ≤ 27V -0.8 0.8 mA 1

IL = 500mA 15V ≤ VI ≤ 30V -0.8 0.8 mA 1, 2, 3

5mA ≤ IL ≤ 1A -0.5 0.5 mA 1, 2, 3

VOOutput Voltage 11.5 12.5 V 1

VI = 15.5V 11.4 12.6 V 1, 2, 3

VI = 15.5V, IL = 1A 11.4 12.6 V 1, 2, 3

VI = 27V 11.4 12.6 V 1, 2, 3

VI = 27V, IL = 1A 11.4 12.6 V 1, 2, 3

RLine Line Regulation IL = 500mA, 14.5V ≤ VI ≤ 25V -120 120 mV 1, 2, 3

IL = 1A, 14.6V ≤ VI ≤ 27V -120 120 mV 1

IL = 1A, 15.0V ≤ VI ≤ 27V -120 120 mV 2, 3

IL = 1A, 16V ≤ VI ≤ 22V -60 60 mV 1, 2, 3

RLoad Load Regulation 5mA ≤ IL ≤ 1.5A -120 120 mV 1

5mA ≤ IL ≤ 1.0A -120 120 mV 2, 3

250mA ≤ IL ≤ 750mA -60 60 mV 1

IOS Current Limit VI = 17V -3.5 -0.02 A 1

VI = 35V -2.0 -0.02 A 1

AC Parameters

The following conditions apply, unless otherwise specified.

AC: VI = 19V, IL = 5mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

RR Ripple Rejection ƒ = 120Hz, IL = 350mA,

eI = 1VRMS

61 dB 4

7 www.national.com

LM140QML

LM140K–15 Electrical Characteristics

DC Parameters

The following conditions apply, unless otherwise specified.

DC: VI = 23V, IL = 5mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

IQQuiescent Current IL = 1A 6.0 mA 1

7.0 mA 2, 3

ΔIQQuiescent Current Change IL = 1A, 18.5V ≤ VI ≤ 30V -0.8 0.8 mA 1

IL = 500mA, 18.5V ≤ VI ≤ 30V -0.8 0.8 mA 2, 3

5mA ≤ IL ≤ 1A -0.5 0.5 mA 1, 2, 3

VOOutput Voltage 14.4 15.6 V 1

VI = 18.5V 14.25 15.75 V 1, 2, 3

VI = 18.5V, IL = 1A 14.25 15.75 V 1, 2, 3

VI = 30V 14.25 15.75 V 1, 2, 3

VI = 30V, IL = 1A 14.25 15.75 V 1, 2, 3

RLine Line Regulation IL = 500mA, 17.5V ≤ VI ≤ 30V -150 150 mV 1

IL = 500mA, 18.5V ≤ VI ≤ 30V -150 150 mV 2, 3

IL = 1A, 17.7V ≤ VI ≤ 30V -75 75 mV 1

IL = 1A, 20V ≤ VI ≤ 26V -75 75 mV 1, 2, 3

RLoad Load Regulation 5mA ≤ IL ≤ 1.5A -150 150 mV 1

5mA ≤ IL ≤ 1.0A -150 150 mV 2, 3

250mA ≤ IL ≤ 750mA -75 75 mV 1

IOS Current Limit VI = 20V -3.5 -0.02 A 1

VI =35V -2.0 -0.02 A 1

AC Parameters

The following conditions apply, unless otherwise specified.

AC: VI = 23V, IL = 5mA

Symbol Parameter Conditions Notes Min Max Unit Sub-

groups

RR Ripple Rejection ƒ = 120Hz, IL = 350mA,

eI = 1VRMS

60 dB 4

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package

junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/

θJA or the number given in the Absolute Maximum Ratings, whichever is lower.

Note 3: Human body model, 100pF discharged through 1.5KΩ

Note 4: VO is set to 90% VRef

Note 5: VDO = VI − VO when VO is 95% of VRef.

www.national.com 8

LM140QML

Revision History Section

Released Revision Section Originator Changes

02/21/06 A New Release, Corporate format L. Lytle 6 MDS data sheets converted into one Corp.

data sheet format. The drift tables were

eliminated from the 883 section since it did not

apply. MDS data sheets MNLM140-05H Rev

0B0, MNLM140-05-K Rev. 0C0,

MNLM140-12H Rev 0A0, MNLM140-12K Rev

0B0, MNLM140-15H Rev 0A0, and

MNLM140-15K Rev 0B0 will be archived.

9 www.national.com

LM140QML

Physical Dimensions inches (millimeters) unless otherwise noted

Metal Can TO-39 (H)

NS Package Number H03A

Steel Metal Can Package (K)

NS Package Number K02C

www.national.com 10

LM140QML

Notes

11 www.national.com

LM140QML

Notes

LM140QML Three Terminal Positive Regulators

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench

Audio www.national.com/audio Analog University www.national.com/AU

Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes

Data Converters www.national.com/adc Distributors www.national.com/contacts

Displays www.national.com/displays Green Compliance www.national.com/quality/green

Ethernet www.national.com/ethernet Packaging www.national.com/packaging

Interface www.national.com/interface Quality and Reliability www.national.com/quality

LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns

Power Management www.national.com/power Feedback www.national.com/feedback

Switching Regulators www.national.com/switchers

LDOs www.national.com/ldo

LED Lighting www.national.com/led

PowerWise www.national.com/powerwise

Serial Digital Interface (SDI) www.national.com/sdi

Temperature Sensors www.national.com/tempsensors

Wireless (PLL/VCO) www.national.com/wireless

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email:

new.feedback@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

German Tel: +49 (0) 180 5010 771

English Tel: +44 (0) 870 850 4288

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265