Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Overview KEMET Power Solutions (KPS) Commercial Series stacked capacitors utilize a proprietary lead-frame technology to vertically stack one or two multilayer ceramic chip capacitors into a single compact surface mount package. The attached lead-frame mechanically isolates the capacitor/s from the printed circuit board, therefore offering advanced mechanical and thermal stress performance. Isolation also addresses concerns for audible, microphonic noise that may occur when a bias voltage is applied. A two chip stack offers up to double the capacitance in the same or smaller design footprint when compared to traditional surface mount MLCCs devices. Providing up to 10 mm of board flex capability, KPS Series capacitors are environmentally friendly and in compliance with RoHS legislation. Available in X7R dielectric, these devices are capable of Pb-Free reflow profiles and provide lower ESR, ESL and higher ripple current capability when compared to other dielectric solutions. Combined with the stability of an X7R dielectric, KEMET's KPS Series devices exhibit a predictable change in capacitance with respect to time and voltage and boast a minimal change in capacitance with reference to ambient temperature. Capacitance change is limited to 15% from -55C to +125C. Benefits * * * * * * * * * * -55C to +125C operating temperature range Reliable and robust termination system EIA 1210, 1812, and 2220 case sizes DC voltage ratings of 10 V, 16 V, 25 V, 50 V, 100 V, and 250 V Capacitance offerings ranging from 0.1 F up to 47 F Available capacitance tolerances of 10% and 20% Higher capacitance in the same footprint Potential board space savings Advanced protection against thermal and mechanical stress Provides up to 10 mm of board flex capability * * * * * Reduces audible, microphonic noise Extremely low ESR and ESL Pb-Free and RoHS Compliant Capable of Pb-Free reflow profiles Non-polar device, minimizing installation concerns * Tantalum and electrolytic alternative Ordering Information C Ceramic 1210 C Case Size Specification/ (L" x W") Series 1210 1812 2220 C = Standard 225 M 4 R 1 C Capacitance Code (pF) Capacitance Tolerance1 Voltage Dielectric Failure Rate/Design 2 significant digits + number of zeros K = 10% M = 20% 8 = 10 V 4 = 16 V 3 = 25 V 5 = 50 V 1 = 100 V A = 250 V R = X7R 7186 Leadframe Packaging/Grade (C-Spec)3 Finish2 1 = KPS Single Chip Stack C = 100% 2 = KPS Double Chip Stack Matte Sn 7186 = 7" Reel Unmarked 7289 = 13" Reel Unmarked Double chip stacks ("2" in the 13th character position of the ordering code) are only available in M (20%) capacitance tolerance. Single chip stacks ("1" in the 13th character position of the ordering code) are available in K (10%) or M (20%) tolerances. 2 Additional leadframe finish options may be available. Contact KEMET for details. 3 Additional reeling or packaging options may be available. Contact KEMET for details. 1 One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Dimensions - Millimeters (Inches) Top View Profile View Single or Double Chip Stack Double Chip Stack Number EIA Size Metric Size of Chips Code Code Single Double Single Chip Stack L Length W Width H Height LW Lead Width Mounting Technique 1210 3225 3.50 (.138) 0.30 (.012) 2.60 (.102) 0.30 (.012) 3.35 (.132) 0.10 (.004) 0.80 (.032) 0.15 (.006) 1812 4532 5.00 (.197) 0.50 (.020) 3.50 (.138) 0.50 (.020) 2.65 (.104) 0.35 (.014) 1.10 (.043) 0.30 (.012) 2220 5650 1210 3225 6.00 (.236) 0.50 (.020) 5.00 (.197) 0.50 (.020) 3.50 (.138) 0.30 (.012) 1.60 (.063) 0.30 (.012) Solder Reflow Only 3.50 (.138) 0.30 (.012) 2.60 (.102) 0.30 (.012) 6.15 (.242) 0.15 (.006) 0.80 (.031) 0.15 (.006) 1812 4532 5.00 (.197) 0.50 (.020) 3.50 (.138) 0.50 (.020) 5.00 (.197) 0.50 (.020) 1.10 (.043) 0.30 (.012) 2220 5650 6.00 (.236) 0.50 (.020) 5.00 (.197) 0.50 (.020) 5.00 (.197) 0.50 (.020) 1.60 (.063) 0.30 (.012) Applications Typical applications include smoothing circuits, DC/DC converters, power supplies (input/output filters), noise reduction (piezoelectric/ mechanical), circuits with a direct battery or power source connection, critical and safety relevant circuits without (integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Markets include industrial, military, automotive and telecom. Qualification/Certification Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance & Reliability. Environmental Compliance Pb-Free and RoHS Compliant. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range -55C to +125C Capacitance Change with Reference to +25C and 0 VDC Applied (TCC) 15% Aging Rate (Maximum % Capacitance Loss/Decade Hour) 3.0% Dielectric Withstanding Voltage (DWV) Dissipation Factor (DF) Maximum Limit @ 25C Insulation Resistance (IR) Limit @ 25C 250% of rated voltage (5 1 seconds and charge/discharge not exceeding 50 mA) 5%(10 V), 3.5%(16 V and 25 V) and 2.5%(50 V to 250 V) See Insulation Resistance Limit Table (Rated voltage applied for 120 5 seconds @ 25C) Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 48 or 1,000 hours. Please refer to a part number specific datasheet for referee time details. To obtain IR limit, divide M-F value by the capacitance and compare to G limit. Select the lower of the two limits. Capacitance and dissipation factor (DF) measured under the following conditions: 1 kHz 50 Hz and 1.0 0.2 Vrms if capacitance 10 F 120 Hz 10 Hz and 0.5 0.1 Vrms if capacitance > 10 F Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON." Post Environmental Limits High Temperature Life, Biased Humidity, Moisture Resistance Dielectric Rated DC Voltage Capacitance Value > 25 X7R 16/25 Dissipation Factor (Maximum %) Capacitance Shift Insulation Resistance 20% 10% of Initial Limit 3.0 All 5.0 < 16 7.5 Insulation Resistance Limit Table EIA Case Size 1,000 Megohm Microfarads or 100 G 500 Megohm Microfarads or 10 G 1210 < 0.39 F 0.39 F 1812 < 2.2 F 2.2 F 2220 < 10 F 10 F (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Electrical Characteristics Z and ESR C2220C225MAR2C Z and C1210C475M5R1C ESR C1210C475M5R1C Z and ESR 4 10 3 10 ESR ESR Z Z 3 10 2 10 2 Magnitude Ohms Magnitude Ohms 10 1 10 0 10 10 10 10 1 10 0 10 -1 10 -2 10 10 -3 10 0 2 4 10 10 10 6 8 -2 -3 10 10 10 -1 10 0 2 10 4 10 10 6 8 10 10 10 Frequency (Hz) Frequency (Hz) Z and ESR C2220C476M3R2C 4 10 ESR Z 2 Magnitude Ohms 10 0 10 10 10 10 -2 -4 -6 10 0 2 10 4 10 10 6 8 10 10 10 Frequency (Hz) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Electrical Characteristics cont'd Impedance - 1812, .10 F, 50 V X7R ESR - 1812, .10 F, 50 V X7R ESR vs. Frequency 10 Impedance vs. Frequency 10000 C1812C104K5R2C (2 Chip Stack) C1812C104K5R1C (1 Chip Stack) C1812C104K5R2C (2 Chip Stack) C1812C104K5R1C (1 Chip Stack) Impedance (Ohms) 1000 100 ESR (Ohms) 1 0.1 10 1 0.1 0.01 1.E+03 1.E+04 1.E+05 1.E+06 Frequency (Hz) 1.E+07 1.E+08 0.01 1.E+03 ESR - 1210, .22 F, 50 V X7R 1.E+05 1.E+06 Frequency (Hz) 1.E+07 1.E+08 Impedance - 1210, .22 F, 50 V X7R ESR vs. Frequency 10 1.E+04 C1210C224K5R2C (2 Chip Stack) C1210C224K5R1C (1 Chip Stack) ESR (Ohms) 0.1 C1210C224K5R2C (2 Chip Stack) C1210C224K5R1C (1 Chip Stack) 100 Impedance (Ohms) 1 Impedance vs. Frequency 1000 10 1 0.1 0.01 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 1.E+08 0.01 1.E+03 1.E+04 Frequency (Hz) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com 1.E+05 1.E+06 Frequency (Hz) 1.E+07 1.E+08 C1020_X7R_KPS_SMD * 5/30/2013 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Electrical Characteristics cont'd Microphonics - 2220, 22 F, 50 V, X7R 60 50 40 30 20 10 0 Sound Pressure (dB) Sound Pressure (dB) Microphonics - 1210, 4.7 F, 50 V, X7R Standard SMD MLCC KPS - 1 Chip Stack 0 5 Vp-p 10 50 40 30 20 0 0 15 50 40 30 Standard SMD MLCC KPS - 2 Chip Stack 10 0 0 5 10 Vp-p 15 2 4 Vp-p 6 Microphonics - 1210, 22 F, 25 V, X7R 20 Sound Pressure (dB) Sound Pressure (dB) Microphonics - 2220, 47 F, 25 V, X7R 20 Standard SMD MLCC KPS - 2 Chip Stack 10 50 40 30 20 Standard SMD MLCC KPS - 2 Chip Stack 10 0 0 2 Vp-p 4 6 Competitive Comparision 60 50 40 30 20 10 0 Ripple Current (Arms) 2220, 22 F, 50 V Absolute Temperature (C) Sound Pressure (dB) Microphonics - 1210, 4.7 F, 50 V, X7R Competitor KEMET - KPS 0 5 Vp-p 10 15 120 100 80 60 40 KEMET KPS, 2220, 22F, 50V rated (2 Chip Stack) 20 Competitor 2220, 22F, 50V rated (2 Chip Stack) 0 0 10 20 Ripple Current (Arms) 30 Note: Refer to Table 4 for test method. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Electrical Characteristics cont'd Board Flex vs. Termination Type Board Flex vs. Termination Type Weibull X7R 1210 10 uF - (22uF KPS Stacked) 2 Standard Termination KPS - 2 Chip Stack 90 Standard Termination KPS - 2 Chip Stack 90 Percent 80 70 60 50 40 Percent Weibull X7R 2220 22uF 25V - (47uF KPS Stacked) 2 30 20 80 70 60 50 40 30 20 10 10 1.5 1.0 2.0 3.0 4.0 Board Flexure (mm) 6.0 5.0 1.0 7. 0 8.0 9.0 10.0 1.5 0 5. 0 6. 0 0 7. 8. 9.0 10.0 Board Flexure to 10 mm Weibull X7R 1210 4.7 uF 50V 2 Weibull X7R 1812 47uF 16V 90 90 80 70 60 50 40 30 Percent Percent 0 4. Board Flexure (mm) Board Flexure to 10 mm 2 0 3. 2.0 20 10 80 70 60 50 40 30 20 10 0 1. 5 1. 0 2. 0 3. 0 4. Board Flexure (mm) 0 5. 0 6. 0 7. 0 0 0 8. 9. 10. 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Board Flexure (mm) 10 C1020_X7R_KPS_SMD * 5/30/2013 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Table 1 - Capacitance Range/Selection Waterfall (1210 - 2220 Case Sizes) Series Capacitance Cap Code C1210 104 224 474 105 225 335 475 106 156 226 336 476 107 0.10 F 0.22 F 0.47 F 1.0 F 2.2 F 3.3 F 4.7 F 10 F 22 F 33 F 47 F 100 F 220 F 104 224 474 105 225 335 475 106 226 336 476 107 227 Capacitance Cap Code C2220 Voltage Code 8 4 3 5 1 A 4 3 5 1 A 4 3 5 1 A Voltage DC 10 16 25 50 100 250 16 25 50 100 250 16 25 50 100 250 Product Availability and Chip Thickness Codes See Table 2 for Chip Thickness Dimensions Capacitance Tolerance 0.10 F 0.22 F 0.47 F 1.0 F 2.2 F 3.3 F 4.7 F 10 F 15 F 22 F 33 F 47 F 100 F C1812 K K K K K K K K K K K K K Single Chip Stack M M M M M M M M M M M M M FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV M M M M M M M M M M M M M FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW FW Voltage DC 10 16 25 50 Voltage Code 8 4 3 5 Series FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV FV GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP GP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP JP FW FW GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR GR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR JR 100 250 16 25 50 100 250 16 25 50 100 250 1 A 4 3 5 1 A 4 3 5 1 A Double Chip Stack C1210 C1812 C2220 These products are protected under US Patent 8,331,078 other patents pending, and any foreign counterparts. Table 2 - Chip Thickness/Packaging Quantities Paper Quantity Plastic Quantity Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel FV FW GP GR JP JR 1210 1210 1812 1812 2220 2220 3.35 0.10 6.15 0.15 2.65 0.35 5.00 0.50 3.50 0.30 5.00 0.50 0 0 0 0 0 0 0 0 0 0 0 0 600 300 500 400 300 200 2,000 1,000 2,000 1,700 1,300 800 Thickness Code Case Size Thickness Range (mm) 7" Reel 13" Reel 7" Reel 13" Reel Paper Quantity Plastic Quantity Package quantity based on finished chip thickness specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. C1020_X7R_KPS_SMD * 5/30/2013 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Table 3 - KPS Land Pattern Design Recommendations (mm) EIA SIZE CODE METRIC SIZE CODE 1210 Median (Nominal) Land Protrusion C Y X V1 V2 3225 1.50 1.14 1.75 5.05 3.40 1812 4532 2.20 1.35 2.87 6.70 4.50 2220 5650 2.69 2.08 4.78 7.70 6.00 Soldering Process To prevent degradation of temperature cycling capability, care must be taken to prevent solder from flowing into the inner side of the lead frames (inner side of "J" lead in contact with the circuit board). After soldering, the capacitors should be air cooled to room temperature before further processing. Forced air cooling is not recommended. Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the capacitor body. The iron should be used to heat the solder pad, applying solder between the pad and the lead, until reflow occurs. Once reflow occurs, the iron should be removed immediately. (Preheating is required when hand soldering to avoid thermal shock.) Profile Feature SnPb Assembly Pb-Free Assembly Preheat/Soak Temperature Minimum (TSmin) 100C 150C Temperature Maximum (TSmax) 150C 200C Time (ts) from Tsmin to Tsmax) 60 - 120 seconds 60 - 120 seconds Ramp-up Rate (TL to TP) 3C/seconds maximum 3C/seconds maximum Liquidous Temperature (TL) 183C 217C Time Above Liquidous (tL) 60 - 150 seconds 60 - 150 seconds Peak Temperature (TP) Time within 5C of Maximum Peak Temperature (tP) Ramp-down Rate (TP to TL) 235C 250C 20 seconds maximum 10 seconds maximum 6C/seconds maximum 6C/seconds maximum Time 25C to Peak Temperature 6 minutes maximum 8 minutes maximum Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. TP TL Temperature KEMET's KPS Series devices are compatible with IR reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for IR reflow reflect the profile conditions of the IPC/J-STD-020D standard for moisture sensitivity testing. tP Maximum Ramp Up Rate = 3C/seconds Maximum Ramp Down Rate = 6C/seconds tL Tsmax Tsmin 25 tS 25C to Peak Time (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Table 4 - Performance & Reliability: Test Methods and Conditions Stress Reference Test or Inspection Method Terminal Strength JIS-C-6429 Appendix 1, Note: Force of 1.8 kg for 60 seconds. Board Flex JIS-C-6429 Appendix 2, Note: 5.0 mm minimum Magnification 50 X. Conditions: Solderability J-STD-002 a) Method B, 4 hours @ 155C, dry heat @ 235C b) Method B @ 215C category 3 c) Method D, category 3 @ 250C Temperature Cycling JESD22 Method JA-104 1,000 cycles (-55C to +125C). Measurement at 24 hours +/- 2 hours after test conclusion. Load Humidity: 1,000 hours 85C/85% RH and 200 VDC maximum. Add 100 K ohm resistor. Measurement at 24 hours +/- 2 hours after test conclusion. Low Volt Humidity: 1,000 hours 85C/85% RH and 1.5 V. Add 100 K ohm resistor. Measurement at 24 hours +/- 2 hours after test conclusion. t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered. Measurement at 24 hours +/- 2 hours after test conclusion. -55C/+125C. Note: Number of cycles required - 300. Maximum transfer time - 20 seconds. Dwell time - 15 minutes. Air-Air. Biased Humidity MIL-STD-202 Method 103 Moisture Resistance MIL-STD-202 Method 106 Thermal Shock MIL-STD-202 Method 107 High Temperature Life MIL-STD-202 Method 108 1,000 hours at 125C with rated voltage applied. Storage Life MIL-STD-202 Method 108 150C, 0 VDC for 1,000 hours. Vibration MIL-STD-202 Method 204 5 g's for 20 minutes, 12 cycles each of 3 orientations. Note: Use 8" X 5" PCB .031" thick, 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10 - 2,000 Hz. Mechanical Shock MIL-STD-202 Method 213 Figure 1 of Method 213, Condition F. Resistance to Solvents MIL-STD-202 Method 215 Add aqueous wash chemical, OKEM Clean or equivalent. Storage & Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature- reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40C and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of receipt. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Construction Reference Item Material A Leadframe Phosphor Bronze - Alloy 510 B Leadframe Attach HMP Solder C D Cu Termination E Ni Sn F Inner Electrode Ni G Dielectric Material BaTiO3 Note: Image is exaggerated in order to clearly identify all components of construction. HMP = High Melting Point Product Marking Laser marking option is not available on: * * * * C0G, Ultra Stable X8R and Y5V dielectric devices EIA 0402 case size devices EIA 0603 case size devices with Flexible Termination option. KPS Commercial and Automotive grade stacked devices. These capacitors are supplied unmarked only. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Table 5 - Carrier Tape Configuration - Embossed Plastic (mm) EIA Case Size Tape Size (W)* Pitch (P1)* 01005 - 0402 8 2 0603 - 1210 8 4 1805 - 1808 12 4 1812 12 8 KPS 1210 12 8 KPS 1812 & 2220 16 12 Array 0508 & 0612 8 4 *Refer to Figure 1 for W and P1 carrier tape reference locations. *Refer to Table 5 for tolerance specifications. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ODo [10 pitches cumulative tolerance on tape 0.2 mm] Po E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity OD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 6 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) R Reference S1 Minimum Note 2 Note 3 25.0 (0.984) 2.0 0.05 0.600 (0.079 0.002) (0.024) 30 (1.181) P2 T Maximum T1 Maximum 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F P1 3.5 0.05 4.0 0.10 (0.138 0.002) (0.157 0.004) 5.5 0.05 8.0 0.10 (0.217 0.002) (0.315 0.004) 7.5 0.05 12.0 0.10 (0.138 0.002) (0.157 0.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 5). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3). (e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 - 200 Bo Maximum Rotation ( 20 10 T) Typical Component Centerline Ao Figure 3 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape s Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 56 10 72 - 200 5 S) Figure 4 - Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com R C1020_X7R_KPS_SMD * 5/30/2013 14 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Figure 5 - Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (O 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 7 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 15 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Figure 6 - Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 7 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 16 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) KEMET Corporation World Headquarters Europe Asia Southern Europe Paris, France Tel: 33-1-4646-1006 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Sasso Marconi, Italy Tel: 39-051-939111 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-460122 2835 KEMET Way Simpsonville, SC 29681 Southeast Lake Mary, FL Tel: 407-855-8886 Espoo, Finland Tel: 358-9-5406-5000 Northeast Wilmington, MA Tel: 978-658-1663 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585 Southeast Asia Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Central Novi, MI Tel: 248-994-1030 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 17 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Electrolytic LifeCalculator http://www.kemet.com:8080/elc Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 18 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) KPS Series, X7R Dielectric, 10 - 250 VDC (Commercial Grade) Digitally signed by Jeannette Calvo DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications, cn=Jeannette Calvo, email=jeannettecalvo@kemet.com Date: 2013.06.07 15:57:29 -04'00' (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com C1020_X7R_KPS_SMD * 5/30/2013 19