a 1 GHz, 5,500 V/s Low Distortion Amplifier AD8009 FEATURES Ultrahigh Speed 5,500 V/s Slew Rate, 4 V Step, G = +2 545 ps Rise Time, 2 V Step, G = +2 Large Signal Bandwidth 440 MHz, G = +2 320 MHz, G = +10 Small Signal Bandwidth (-3 dB) 1 GHz, G = +1 700 MHz, G = +2 Settling Time 10 ns to 0.1%, 2 V Step, G = +2 Low Distortion over Wide Bandwidth SFDR -66 dBc @ 20 MHz, Second Harmonic -75 dBc @ 20 MHz, Third Harmonic Third Order Intercept (3IP) 26 dBm @ 70 MHz, G = +10 Good Video Specifications Gain Flatness 0.1 dB to 75 MHz 0.01% Differential Gain Error, RL = 150 0.01 Differential Phase Error, RL = 150 High Output Drive 175 mA Output Load Drive 10 dBm with -38 dBc SFDR @ 70 MHz, G = +10 Supply Operation +5 V to 5 V Voltage Supply 14 mA (Typ) Supply Current APPLICATIONS Pulse Amplifier IF/RF Gain Stage/Amplifiers High Resolution Video Graphics High Speed Instrumentations CCD Imaging Amplifier 2 G = +2 RF = 301 RL = 150 1 FUNCTIONAL BLOCK DIAGRAMS 8-Lead Plastic SOIC (R-8) 7 +VS +IN 3 6 OUT -VS 4 5 NC -4 -5 -6 -7 -8 100 10 FREQUENCY RESPONSE (MHz) 1000 Figure 1. Large Signal Frequency Response; G = +2 and +10 REV. F Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 4 -IN -VS 2 +IN 3 The high slew rate reduces the effect of slew rate limiting and results in the large signal bandwidth of 440 MHz required for high resolution video graphic systems. Signal quality is maintained over a wide bandwidth with worst-case distortion of -40 dBc @ 250 MHz (G = +10, 1 V p-p). For applications with multitone signals, such as IF signal chains, the third order intercept (3IP) of 12 dBm is achieved at the same frequency. This distortion performance coupled with the current feedback architecture make the AD8009 a flexible component for a gain stage amplifier in IF/RF signal chains. The AD8009 is capable of delivering over 175 mA of load current and will drive four back terminated video loads while maintaining low differential gain and phase error of 0.02% and 0.04, respectively. The high drive capability is also reflected in the ability to deliver 10 dBm of output power @ 70 MHz with -38 dBc SFDR. The AD8009 is available in a small SOIC package and will operate over the industrial temperature range -40C to +85C. The AD8009 is also available in an SOT-23-5 and will operate over the commercial temperature range of 0C to 70C. -30 G=2 RF = 301 VO = 2V p-p SECOND 100 LOAD -50 -60 SECOND 150 LOAD -70 THIRD 100 LOAD -80 1 +VS PRODUCT DESCRIPTION DISTORTION (dBc) NORMALIZED GAIN (dB) -3 5 The AD8009 is an ultrahigh speed current feedback amplifier with a phenomenal 5,500 V/s slew rate that results in a rise time of 545 ps, making it ideal as a pulse amplifier. -40 G = +10 RF = 200 RL = 100 VOUT 1 NC = NO CONNECT -1 -2 AD8009 8 NC 2 -IN 0 VO = 2V p-p AD8009 NC 1 5-Lead SOT-23 (RT-5) THIRD 150 LOAD -90 -100 1 10 FREQUENCY RESPONSE (MHz) 70 Figure 2. Distortion vs. Frequency; G = +2 One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2004 Analog Devices, Inc. All rights reserved. (@ T = 25C, V = 5 V, R = 100 ; for R Package: R = 301 for G = +1, +2, AD8009-SPECIFICATIONS R = 200 for G = +10; for RT Package: R = 332 for G = +1, R = 226 for G = +2 and R = 191 for G = +10, unless otherwise noted.) A F F Model DYNAMIC PERFORMANCE -3 dB Small Signal Bandwidth, VO = 0.2 V p-p R Package RT Package Large Signal Bandwidth, VO = 2 V p-p Gain Flatness 0.1 dB, VO = 0.2 V p-p Slew Rate Settling Time to 0.1% Rise and Fall Time HARMONIC/NOISE PERFORMANCE Second Harmonic G = +2, VO = 2 V p-p Third Harmonic Third Order Intercept (3IP) W.R.T. Output, G = +10 Input Voltage Noise Input Current Noise Differential Gain Error Differential Phase Error S L F F F Conditions G = +1, RF = 301 G = +1, RF = 332 G = +2 G = +10 G = +2 G = +10 G = +2, RL = 150 G = +2, RL = 150 , 4 V Step G = +2, RL = 150 , 2 V Step G = +10, 2 V Step G = +2, RL = 150 , 4 V Step Min 480 300 390 235 45 4,500 10 MHz 20 MHz 70 MHz 10 MHz 20 MHz 70 MHz 70 MHz 150 MHz 250 MHz f = 10 MHz f = 10 MHz, +In f = 10 MHz, -In NTSC, G = +2, RL = 150 NTSC, G = +2, RL = 37.5 NTSC, G = +2, RL = 150 NTSC, G = +2, RL = 37.5 DC PERFORMANCE Input Offset Voltage AD8009AR/JRT Typ Max 1,000 845 700 350 440 320 75 5,500 10 25 0.725 MHz MHz MHz MHz MHz MHz MHz V/s ns ns ns -73 -66 -56 -77 -75 -58 26 18 12 1.9 46 41 0.01 0.02 0.01 0.04 dBc dBc dBc dBc dBc dBc dBm dBm dBm nV/Hz pA/Hz pA/Hz % % Degrees Degrees 2 TMIN to TMAX Offset Voltage Drift -Input Bias Current TMIN to TMAX +Input Bias Voltage TMIN to TMAX Open-Loop Transresistance 90 TMIN to TMAX INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Short-Circuit Current +Input -Input +Input VCM = 2.5 3.7 RL = 10 , PD Package = 0.7 W 150 POWER SUPPLY Operating Range Quiescent Current Power Supply Rejection Ratio 50 4 50 75 50 75 250 170 5 7 150 150 mV mV V/C A A A A k k k pF V dB 3.8 175 330 V mA mA 14 64 0.03 0.05 0.03 0.08 110 8 2.6 3.8 52 +5 TMIN to TMAX VS = 4 V to 6 V Unit 70 6 16 18 V mA mA dB Specifications subject to change without notice. -2- REV. F AD8009 (@ TA = 25C, VS = 5 V, RL = 100 , for R Package: RF = 301 for G = +1, +2, SPECIFICATIONS R = 200 for G = +10). F Model DYNAMIC PERFORMANCE -3 dB Small Signal Bandwidth, VO = 0.2 V p-p Large Signal Bandwidth, VO = 2 V p-p Gain Flatness 0.1 dB, VO = 0.2 V p-p Slew Rate Settling Time to 0.1% Rise and Fall Time HARMONIC/NOISE PERFORMANCE Second Harmonic G = +2, VO = 2 V p-p Third Harmonic Input Voltage Noise Input Current Noise Conditions Min Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Short-Circuit Current POWER SUPPLY Operating Range Quiescent Current Power Supply Rejection Ratio 630 430 300 365 250 65 2,100 10 25 0.725 MHz MHz MHz MHz MHz MHz V/s ns ns ns 10 MHz 20 MHz 70 MHz 10 MHz 20 MHz 70 MHz f = 10 MHz f = 10 MHz, +In f = 10 MHz, -In -74 -67 -48 -76 -72 -44 1.9 46 41 dBc dBc dBc dBc dBc dBc nV/Hz pA/Hz pA/Hz 1 50 50 +Input -Input +Input VCM = 1.5 V to 3.5 V 50 RL = 10 , PD Package = 0.7 W VS = 4.5 V to 5.5 V -3- 64 4 150 150 mV A A 110 8 2.6 1.2 to 3.8 52 k pF V dB 1.1 to 3.9 175 330 V mA mA +5 Specifications subject to change without notice. REV. F Unit G = +1, RF = 301 G = +2 G = +10 G = +2 G = +10 G = +2, RL = 150 G = +2, RL = 150 , 4 V Step G = +2, RL = 150 , 2 V Step G = +10, 2 V Step G = +2, RL = 150 , 4 V Step DC PERFORMANCE Input Offset Voltage -Input Bias Current +Input Bias Voltage INPUT CHARACTERISTICS Input Resistance AD8009AR/JRT Typ Max 10 70 6 12 V mA dB AD8009 ABSOLUTE MAXIMUM RATINGS 1 MAXIMUM POWER DISSIPATION Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V Internal Power Dissipation2 Small Outline Package (R) . . . . . . . . . . . . . . . . . . . . . . . 0.75 W Input Voltage (Common-Mode) . . . . . . . . . . . . . . . . . . . . VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . 3.5 V Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves Storage Temperature Range R Package . . . . -65C to +125C Operating Temperature Range (A Grade) . . . -40C to +85C Operating Temperature Range (J Grade) . . . . . . . 0C to 70C Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300C The maximum power that can be safely dissipated by the AD8009 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150C. Exceeding this limit temporarily may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of 175C for an extended period can result in device failure. While the AD8009 is internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (150C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves. NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Specification is for device in free air: 8-Lead SOIC Package: JA = 155C/W. 5-Lead SOT-23 Package: JA = 240C/W. 2.0 MAXIMUM POWER DISSIPATION (W) TJ = 150 C 1.5 8-LEAD SOIC PACKAGE 1.0 0.5 5-LEAD SOT-23 PACKAGE 0 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 AMBIENT TEMPERATURE (C) 70 80 90 Figure 3. Plot of Maximum Power Dissipation vs. Temperature ORDERING GUIDE Model AD8009AR AD8009AR-REEL AD8009AR-REEL7 AD8009ARZ* AD8009ARZ-REEL* AD8009ARZ-REEL7* AD8009JRT-R2 AD8009JRT-REEL AD8009JRT-REEL7 AD8009JRTZ-REEL* AD8009JRTZ-REEL7* AD8009ACHIPS Temperature Range Package Description Package Option Branding -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 8-Lead SOIC 8-Lead SOIC 8-Lead SOIC 8-Lead SOIC 8-Lead SOIC 8-Lead SOIC 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 Die R-8 R-8 R-8 R-8 R-8 R-8 RT-5 RT-5 RT-5 RT-5 RT-5 HKJ HKJ HKJ HKJ HKJ *Z = Pb-free part. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8009 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. -4- REV. F Typical Performance Characteristics-AD8009 3 6.2 2 6.1 G = +1, R G = +1, RT 6.0 0 R PACKAGE: RL = 100 G = +2, R AND RT VO = 200mV p-p G = +1, +2: RF = 301 G = +10, R AND RT G = +10: RF = 200 RT PACKAGE: G = +1: RF = 332 G = +2: RF = 226 G = +10: RF = 191 -1 -2 -3 -4 -5 G = +2 RF = 301 RL = 150 VO = 200mV p-p 5.8 5.7 5.6 5.5 5.4 -6 -7 5.9 GAIN FLATNESS (dB) NORMALIZED GAIN (dB) 1 5.3 5.2 1 10 100 1 1000 10 100 FREQUENCY (MHz) FREQUENCY (MHz) TPC 1. Frequency Response; G = +1, +2, +10, R and RT Packages TPC 4. Gain Flatness; G = +2 0.4 8 G = +2 RF = 301 RL = 150 VO = 200mV p-p VS = 5V 7 0.3 6 0.2 G = +2 RF = 301 RL = 150 VO AS SHOWN 4 3 2 GAIN FLATNESS (dB) 5 GAIN (dB) 1000 4V p-p 2V p-p 1 0.1 0 -0.1 0 -0.2 -1 -2 1 10 100 FREQUENCY (MHz) -0.3 1000 1 TPC 2. Large Signal Frequency Response; G = +2 10 100 FREQUENCY (MHz) 1000 10000 TPC 5. Gain Flatness; G = +2; VS = 5 V 8 22 7 21 +85C 6 20 -40C 19 -40C G = +2 RF = 301 RL = 150 VO = 2V p-p 4 3 2 GAIN (dB) GAIN (dB) 5 +85C 17 2V p-p 4V p-p 16 1 15 0 14 -1 13 12 -2 1 10 100 FREQUENCY (MHz) 1000 1 TPC 3. Large Signal Frequency Response vs. Temperature; G = +2 REV. F G = +10 RF = 200 RL = 100 VO AS SHOWN 18 10 100 FREQUENCY (MHz) 1000 TPC 6. Large Signal Frequency Response; G = +10 -5- AD8009 22 -35 21 -40 20 -45 70MHz GAIN (dB) -40C G = +10 RF = 200 RL = 100 VO = 2V p-p 18 17 DISTORTION (dBc) -50 19 +85C 16 15 -55 -65 200 -70 22.1 50 POUT 50 50 -80 13 -85 -10 -8 12 1 10 100 FREQUENCY (MHz) -6 -4 -2 1000 0 2 4 6 8 10 12 14 POUT (dBm) TPC 10. Second Harmonic Distortion vs. POUT; (G = +10) TPC 7. Large Signal Frequency Response vs. Temperature; G = +10 -30 0.02 DIFF GAIN (%) G=2 RF = 301 VO = 2V p-p -40 SECOND, 100 LOAD -50 -60 -70 THIRD, 100 LOAD -80 THIRD, 150 LOAD -90 -100 1 10 FREQUENCY RESPONSE (MHz) 70 G = +2 RF = 301 0.01 RL = 150 0.00 -0.01 -0.02 SECOND, 150 LOAD DIFF PHASE (Degrees) DISTORTION (dBc) 5MHz -60 -75 14 RL = 37.5 0 100 IRE 0.10 G = +2 0.05 RF = 301 RL = 37.5 -0.00 RL = 150 -0.05 -0.10 TPC 8. Distortion vs. Frequency; G = +2 0 100 IRE TPC 11. Differential Gain and Phase -20 -30 G = +2 RF = 301 RL = 100 VO = 2V p-p VS = 5V G = +10 RF = 200 RL = 100 VO = 2V p-p -35 THIRD -40 -45 DISTORTION (dBc) -30 DISTORTION (dBc) 250MHz -40 SECOND -50 -60 SECOND -50 -55 -60 -65 THIRD -70 -70 -75 -80 -80 1 10 100 5 200 10 70 FREQUENCY (MHz) FREQUENCY (MHz) TPC 12. Distortion vs. Frequency; G = +10 TPC 9. Distortion vs. Frequency; G = +2; VS = 5 V -6- REV. F AD8009 10 -35 -40 G = +2 RF = 301 RL = 100 100mV p-p ON TOP OF VS 0 -45 DISTORTION (dBc) -10 250MHz -50 70MHz -55 PSRR (dB) -20 -60 -65 -70 5MHz -PSRR -30 +PSRR -40 -75 200 -80 -50 22.1 50 P OUT -85 -95 -10 -8 -6 -4 -2 0 2 4 -60 50 50 -90 6 8 10 12 -70 0.03 0.1 14 1 TPC 13. Third Harmonic Distortion vs. POUT; (G = +10) 500 100 TPC 16. PSRR vs. Frequency 300 50 200 250 22.1 50 P OUT 40 INPUT CURRENT (pA/ Hz) 45 INTERCEPT POINT (dBm) 10 FREQUENCY (MHz) POUT (dBm) 50 50 35 30 25 20 200 150 100 NONINVERTING CURRENT 50 15 INVERTING CURRENT 0 10 10 100 FREQUENCY (MHz) 250 10 100 1M 0 1M 10M 100M 250M -10 301 PHASE 1k -80 VO 154 -25 CMRR (dB) RL = 100 301 VIN = 200mV p-p -20 -40 GAIN PHASE (Degrees) TRANSRESISTANCE () 100k TPC 17. Current Noise vs. Frequency -15 10k 10k FREQUENCY (Hz) TPC 14. Two Tone, Third Order IMD Intercept vs. Frequency; G = +10 100k 1k 154 100 -30 -35 -40 -45 -120 -50 -55 100 0.01 0.1 1 10 100 -160 1000 -60 1 FREQUENCY (MHz) TPC 15. Transresistance and Phase vs. Frequency REV. F 10 100 FREQUENCY (MHz) TPC 18. CMRR vs. Frequency -7- 1000 AD8009 2.0 G = +2 RF = 301 1.8 10 1.6 (VSWR) OUTPUT RESISTANCE () 100 1 1.4 1.2 0.1 1.0 0.01 0.03 0.1 1 10 100 0 0.1 500 1 10 FREQUENCY (MHz) FREQUENCY (MHz) TPC 19. Output Resistance vs. Frequency 100 500 TPC 22. Input VSWR; G = +10 10 20 16 POUT MAX (dBm) INPUT VOLTAGE NOISE (nV/ Hz) 18 8 6 4 G = +2 RF = 301 14 12 G = +10 RF = 200 10 8 RF 6 2 RG 50 4 50 2 0 10 POUT 50 0 100 1k 10k 100k 1M 10M 5 100M 250M 10 100 250 FREQUENCY (MHz) FREQUENCY (Hz) TPC 20. Voltage Noise vs. Frequency TPC 23. Maximum Output Power vs. Frequency 25 -20 -30 G = +10 RF = 200 20 -50 15 G = +10 RF = 301 RL = 100 10 S12 (dB) NOISE FIGURE (dB) -40 -60 -70 -80 5 -90 0 1 10 100 SOURCE RESISTANCE () 500 1 TPC 21. Noise Figure 10 100 FREQUENCY (MHz) 1000 TPC 24. Reverse Isolation (S12); G = +10 -8- REV. F AD8009 2.2 G = +2 RF = 301 RL = 150 VO = 2V p-p CCOMP 2.0 49.9 49.9 1.8 (VSWR) 200 1.6 22.1 1.4 CCOMP = 0pF 1.2 CCOMP = 3pF 1.0 500mV 0 0.1 1 10 FREQUENCY (MHz) 100 500 TPC 25. Output VSWR; G = +10 VOUT 100 90 1ns TPC 28. 2 V Transient Response; G = +2 G = +2 RF = 301 RL = 150 VO = 4V p-p G = +10 RF = 200 RL = 100 VIN = 2VSTEP 10 0% 2V 2V 250ns 1V TPC 26. Overdrive Recovery; G = +10 TPC 29. 4 V Transient Response; G = +2 G = +10 RF = 200 RL = 100 VO = 200mV p-p G = +2 RF = 301 RL = 150 VO = 200mV p-p 50mV 50mV 1ns TPC 27. 2 V Transient Response; G = +2 REV. F 1.5ns 2ns TPC 30. Small Signal Transient Response; G = +10 -9- AD8009 G = +10 RF = 200 RL = 100 VO = 2V p-p V O 2ns 50mV TPC 31. 2 V Transient Response; G = +10 1ns TPC 34. 2 V Transient Response; VS = 5 V; G = +2 8 G = +10 RF = 200 RL = 100 VO = 4V p-p 12 CA = 2pF 3dB/div 7 9 6 6 CA = 1pF 1dB/div GAIN (dB) 5 3 4 0 CA = 0pF 1dB/div 3 -3 2 -6 VOUT = 200mV p-p VIN 1 100 499 3ns 1V CA -9 VOUT 50 0 -12 499 -15 -1 1 TPC 32. 4 V Transient Response; G = +10 GAIN (dB) 500mV VS = 5V G = +2 RF = 301 RL = 150 VO = 200mV p-p 10 1000 100 FREQUENCY (MHz) TPC 35. Small Signal Frequency Response vs. Parasitic Capacitance CA = 2pF CA CA = 1pF V O VIN VOUT 50 499 100 499 VOUT = 200mV p-p VS = 5V CA = 0pF 50mV VS = 5V G = +2 RF = 301 RL = 150 VO = 200mV p-p 1ns 40mV TPC 33. Small Signal Transient Response; VS = 5 V; G = +2 1.5ns TPC 36. Small Signal Pulse Response vs. Parasitic Capacitance -10- REV. F AD8009 0 HP8753D AD8009 G=2 RF = RG= 301 DRIVING WAVETEK 5201 TUNABLE BPF fC = 50MHz -10 -20 Z IN = 50 Z OUT = 50 -30 0.001F 3 49.9 0.1F + REJECTION (dB) +5V 10F 7 AD8009 2 49.9 6 WAVETEK 5201 BPF 301 -5V -60 -80 -90 0.001F 0.1F 10F + TPC 37. AD8009 Driving a Band-Pass RF Filter APPLICATIONS All current feedback op amps are affected by stray capacitance on their -INPUT. TPCs 35 and 36 illustrate the AD8009's response to such capacitance. TPC 35 shows the bandwidth can be extended by placing a capacitor in parallel with the gain resistor. The small signal pulse response corresponding to such an increase in capacitance/bandwidth is shown in TPC 36. As a practical consideration, the higher the capacitance on the -INPUT to GND, the higher RF needs to be to minimize peaking/ringing. RF Filter Driver CENTER 50.000 MHz SPAN 80.000 MHz TPC 38. Frequency Response of Band-Pass Filter Circuit TPC 37 shows a circuit for driving and measuring the frequency response of a filter, a Wavetek 5201 tunable band-pass filter that is tuned to a 50 MHz center frequency. The HP8753D network provides a stimulus signal for the measurement. The analyzer has a 50 source impedance that drives a cable that is terminated in 50 at the high impedance noninverting input of the AD8009. The AD8009 is set at a gain of +2. The series 50 resistor at the output, along with the 50 termination provided by the filter and its termination, yield an overall unity gain for the measured path. The frequency response plot of TPC 38 shows the circuit to have an insertion loss of 1.3 dB in the pass band and about 75 dB rejection in the stop band. The output drive capability, wide bandwidth, and low distortion of the AD8009 are well suited for creating gain blocks that can drive RF filters. Many of these filters require that the input be driven by a 50 source, while the output must be terminated in 50 for the filters to exhibit their specified frequency response. REV. F -50 -70 4 301 -40 -11- AD8009 PRIMARY MONITOR 75 COAX IOUTR 75 RED 75 75 GREEN 75 75 BLUE 75 ADV7160/ ADV7162 IOUTG IOUTB 5V + 0.1F 10F 7 3 AD8009 2 6 75 ADDITIONAL MONITOR 75 COAX 4 RED 75 301 301 0.1F -5V + 10F 3 6 AD8009 75 2 GREEN 75 BLUE 75 301 301 3 6 AD8009 75 2 301 301 Figure 4. Driving an Additional High Resolution Monitor Using Three AD8009s RGB Monitor Driver High resolution computer monitors require very high full power bandwidth signals to maximize their display resolution. The RGB signals that drive these monitors are generally provided by a current-out RAMDAC that can directly drive a 75 doubly terminated line. There are times when the same output wants to be delivered to additional monitors. The termination provided internally by each monitor prohibits the ability to simply connect a second monitor in parallel with the first. Additional buffering must be provided. Figure 4 shows a connection diagram for two high resolution monitors being driven by an ADV7160 or ADV7162, a 220 MHz (Megapixel per second) triple RAMDAC. This pixel rate requires a driver whose full power bandwidth is at least half the pixel rate or 110 MHz. This is to provide good resolution for a worst-case signal that swings between zero scale and full scale on adjacent pixels. The primary monitor is connected in the conventional fashion with a 75 termination to ground at each end of the 75 cable. Sometimes this configuration is called "doubly terminated" and is used when the driver is a high output impedance current source. For the additional monitor, each of the RGB signals close to the RAMDAC output is applied to a high input impedance, noninverting input of an AD8009 that is configured for a gain of +2. The outputs each drive a series 75 resistor, cable, and termination resistor in the monitor that divides the output signal by two, thus providing an overall unity gain. This scheme is referred to as "back termination" and is used when the driver is a low output impedance voltage source. Back termination requires that the voltage of the signal be double the value that the monitor sees. Double termination requires that the output current be double the value that flows in the monitor termination. -12- REV. F AD8009 Driving a Capacitive Load A capacitive load, like that presented by some A/D converters, can sometimes be a challenge for an op amp to drive depending on the architecture of the op amp. Most of the problem is caused by the pole created by the output impedance of the op amp and the capacitor that is driven. This creates extra phase shift that can eventually cause the op amp to become unstable. One way to prevent instability and improve settling time when driving a capacitor is to insert a resistor in series between the op amp output and the capacitor. The feedback resistor is still connected directly to the output of the op amp, while the series resistor provides some isolation of the capacitive load from the op amp output. +5V G = +2: RF = 301 = RG G = +10: RF = 200, RG = 22.1 0.001F 3 RT 49.9 RG + 0.1F Figure 5 shows such a circuit with an AD8009 driving a 50 pF load. With RS = 0, the AD8009 circuit will be unstable. For a gain of +2 and +10, it was found experimentally that setting RS to 42.2 will minimize the 0.1% settling time with a 2 V step at the output. The 0.1% settling time was measured to be 40 ns with this circuit. For smaller capacitive loads, a smaller RS will yield optimal settling time, while a larger RS will be required for larger capacitive loads. Of course, a larger capacitance will always require more time for settling to a given accuracy than a smaller one, and this will be lengthened by the increase in RS required. At best, a given RC combination will require about seven time constants by itself to settle to 0.1%, so a limit will be reached where too large a capacitance cannot be driven by a given op amp and still meet the system's required settling time specification. 10F 7 AD8009 2 6 2VSTEP RS CL 4 50pF RF 0.001F -5V 0.1F + 10F Figure 5. Capacitive Load Drive Circuit REV. F -13- AD8009 OUTLINE DIMENSIONS 8-Lead Standard Small Outline Package [SOIC] (R-8) Dimensions shown in millimeters and (inches) 5.00 (0.1968) 4.80 (0.1890) 4.00 (0.1574) 3.80 (0.1497) 8 5 1 4 6.20 (0.2440) 5.80 (0.2284) 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 0.51 (0.0201) 0.31 (0.0122) COPLANARITY SEATING 0.10 PLANE 0.50 (0.0196) 45 0.25 (0.0099) 1.75 (0.0688) 1.35 (0.0532) 8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 5-Lead Small Outline Transistor Package [SOT-23] (RT-5) Dimensions shown in millimeters 2.90 BSC 5 4 2.80 BSC 1.60 BSC 1 2 3 PIN 1 0.95 BSC 1.30 1.15 0.90 1.90 BSC 1.45 MAX 0.15 MAX 0.50 0.30 SEATING PLANE 0.22 0.08 10 5 0 0.60 0.45 0.30 COMPLIANT TO JEDEC STANDARDS MO-178AA -14- REV. F AD8009 Revision History Location Page 9/04--Data Sheet changed from REV. E to REV. F. Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Change to TPC 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3/03--Data Sheet changed from REV. D to REV. E. Updated Data Sheet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Universal Changes to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Changes to Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Deleted AD8009EB from ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Inserted new TPC 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Inserted new TPC 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Inserted new TPC 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Inserted new TPCs 33 and 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 REV. F -15- -16- C01011-0-9/04(F)