A3282 Chopper-Stabilized Hall-Effect Latch Last Time Buy These parts are in production but have been determined to be LAST TIME BUY. This classification indicates that the product is obsolete and notice has been given. Sale of this device is currently restricted to existing customer applications. The device should not be purchased for new design applications because of obsolescence in the near future. Samples are no longer available. Date of status change: February 1, 2010 Deadline for receipt of LAST TIME BUY orders: July 30, 2010 Recommended Substitutions: Our next generation recommended substitutes are: * For the A3282ELHLT-T, we recommend the A1222ELHLX-T. * For the A3282LLHLT-T, we recommend the A1222LLHLX-T. * For the A3282LUA-T, we recommend the A1222LUA-T. NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. A3282 Chopper-Stabilized Hall-Effect Latch Features and Benefits Description Chopper stabilization Superior temperature stability Extremely low switchpoint drift Insensitive to physical stress Reverse battery protection Output short circuit protection Solid state reliability Small size Robust EMC capability High ESD ratings (HBM) The A3282 Hall-effect sensor IC is a temperature stable, stress-resistant latch. Superior high-temperature performance is made possible through an Allegro(R) patented dynamic offset cancellation that utilizes chopper-stabilization. This method reduces the offset voltage normally caused by device overmolding, temperature dependencies, and thermal stress. The A3282 complements the current Allegro family of chopperstabilized latching devices. The A3282 includes the following on a single silicon chip: voltage regulator, Hall-voltage generator, small-signal amplifier, chopper stabilization, Schmitt trigger, and a short circuit protected open-drain output. Advanced BiCMOS wafer fabrication processing is used to take advantage of low-voltage requirements, component matching, very low input-offset errors, and small component geometries. Packages: 3 pin SOT23W (suffix LH), and 3 pin SIP (suffix UA) This device requires the presence of both south and north polarity magnetic fields for operation. In the presence of a south polarity field of sufficient strength, the device output latches on, and only switches off when a north polarity field of sufficient strength is present. Continued on the next page... Not to scale Functional Block Diagram VCC Regulator Low-Pass Filter Amp Sample and Hold Dynamic Offset Cancellation To All Subcircuits VOUT Control Current Limit <1 GND A3282-DS, Rev. 8 Chopper-Stabilized Hall Effect Latch A3282 Description (continued) The A3282 is rated for operation between the ambient temperatures -40C and 85C for the E temperature range, and -40C to 150C for the L temperature range. The two package styles available provide magnetically optimized solutions for most applications. Package LH is an SOT23-W, a miniature low-profile surface-mount package, while package UA is a three-lead ultramini SIP for through-hole mounting. Each package is available in a lead (Pb) free version, with 100% matte tin plated leadframes. Selection Guide Part Number Packing1 Mounting A3282ELHLT-T2 7-in. reel, 3000 pieces/reel A3282LLHLT-T2 7-in. reel, 3000 pieces/reel A3282LUA-T2 Bulk, 500 pieces/bag 3-pin SOT23W surface mount 3-pin SOT23W surface mount 3-pin SIP through hole Ambient, TA (C) BRP(MIN) (G) BOP(MAX) (G) -150 150 -40 to 85 -40 to 150 1Contact Allegro for additional packing options. is in production but has been determined to be NOT FOR NEW DESIGN. This classification indicates that sale of the variant is currently restricted to existing customer applications. The variant should not be purchased for new design applications because obsolescence in the near future is probable. Samples are no longer available. Status change: August 12, 2009. 2Variant Absolute Maximum Ratings Characteristic Symbol Notes Rating Units Supply Voltage VCC 28 V Reverse-Supply Voltage VRCC -18 V VOUT 28 V IOUTSINK Internally Limited - Output Off Voltage Output Current IROUT -10 mA Magnetic Flux Density Reverse-Output Current B Unlimited G Operating Ambient Temperature TA Maximum Junction Temperature Storage Temperature Range E -40 to 85 C Range L -40 to 150 C TJ(max) 165 C Tstg -65 to 170 C Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 2 Chopper-Stabilized Hall Effect Latch A3282 OPERATING CHARACTERISTICS valid over full operating voltage and ambient temperature ranges, unless otherwise noted Characteristic Symbol Test Conditions Min. Typ. Max. Units Electrical Characteristics Supply Voltage1 Output Leakage Current VCC Operating, TJ < 165C 3.6 - 24 V IOUTOFF VOUT = 24 V, B < BRP - - 10 A VOUT(SAT) IOUT = 20 mA, B > BOP - 250 500 mV Output Current Limit IOM B > BOP 30 - 60 mA Power-On Time tPO VCC > 3.6 V Output On Voltage - 8 50 s - 200 - kHz RLOAD = 820 , CS = 20 pF - 0.2 1 s RLOAD = 820 , CS = 20 pF - 0.2 1 s ICCON B > BOP - 1.6 3.5 mA ICCOFF B < BRP - 1.6 3.5 mA VRCC = -18 V - - -2 mA VZ ICC = 6.5 mA; TA = 25C 28 - - V IZ VS = 28 V - - 6.5 mA BOP South pole adjacent to branded face of device 70 110 150 G Release Point BRP North pole adjacent to branded face of device -150 -110 -70 G Hysteresis BHYS BOP - BRP 140 220 300 G Chopping Frequency fc Output Rise Time2 tr Output Fall Time2 tf Supply Current Reverse Battery Current Supply Zener Clamp Voltage Supply Zener Current3 IRCC Magnetic Characteristics4 Operate Point 1 Maximum voltage must be adjusted for power dissipation and junction temperature, see Power Derating section. 2 C = oscilloscope probe capacitance. S 3 Maximum current limit is equal to the maximum I CC(MAX) + 3 mA. 4 Magnetic flux density, B, is indicated as a negative value for north-polarity magnetic fields, and as a positive value for south-polarity magnetic fields. This so-called algebraic convention supports arithmetic comparison of north and south polarity values, where the relative strength of the field is indicated by the absolute value of B, and the sign indicates the polarity of the field (for example, a -100 G field and a 100 G field have equivalent strength, but opposite polarity). DEVICE QUALIFICATION PROGRAM Contact Allegro for information. EMC (Electromagnetic Compatibility) REQUIREMENTS Contact Allegro for information. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 3 Chopper-Stabilized Hall Effect Latch A3282 Electrical Characteristic Data Supply Current (On) versus Ambient Temperature Supply Current (On) versus Supply Voltage 5.0 5.0 4.0 VCC (V) 3.0 24 3.6 2.0 ICCON (mA) ICCON (mA) 4.0 1.0 3.0 -40 25 150 2.0 1.0 0 -50 TA (C) 0 0 50 TA (C) 100 150 0 25 4.0 VCC (V) 3.0 24 3.6 2.0 ICCOFF (mA) ICCOFF (mA) 20 5.0 4.0 TA (C) -40 25 150 3.0 2.0 1.0 1.0 0 0 0 50 TA (C) 100 0 150 5 10 15 20 25 VCC (V) Output Voltage (On) versus Ambient Temperature Output Voltage (On) versus Supply Voltage 500 500 450 450 400 400 350 350 300 VCC (V) 250 24 3.6 200 150 VOUT(SAT) (mV) VOUT(SAT) (mV) 15 Supply Current (Off) versus Supply Voltage 5.0 TA (C) 300 -40 25 150 250 200 150 100 100 50 50 0 -50 10 VCC (V) Supply Current (Off) versus Ambient Temperature -50 5 0 0 50 TA (C) 100 150 0 5 10 15 20 25 VCC (V) Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 4 Chopper-Stabilized Hall Effect Latch A3282 Magnetic Characteristic Data Operate Point versus Ambient Temperature 150 150 140 140 130 130 VCC (V) 110 24 3.8 100 120 TA (C) -40 25 150 BOP (G) 120 BOP (G) Operate Point versus Supply Voltage 110 100 90 90 80 80 79 79 -50 0 50 TA (C) 100 150 0 20 25 -80 -80 -90 -90 -100 -100 VCC (V) -110 24 3.8 -120 TA (C) -40 25 150 BRP (G) BRP (G) -70 -110 -120 -130 -130 -140 -140 -150 -150 0 50 TA (C) 100 0 150 5 10 15 20 25 VCC (V) Hysteresis versus Ambient Temperature Hysteresis versus Supply Voltage 300 300 280 280 260 260 240 VCC (V) 220 24 3.8 200 BHYS (G) BHYS (G) 15 Release Point versus Supply Voltage -70 TA (C) 240 -40 25 150 220 200 180 180 160 160 140 -50 10 VCC (V) Release Point versus Ambient Temperature -50 5 140 0 50 TA (C) 100 150 0 5 10 15 20 25 VCC (V) Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 5 Chopper-Stabilized Hall Effect Latch A3282 THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information Characteristic Symbol Test Conditions* RJA Package Thermal Resistance Value Units Package LH, 1-layer PCB with copper limited to solder pads 228 C/W Package LH, 2-layer PCB with 0.463 in.2 of copper area each side connected by thermal vias 110 C/W Package UA, 1-layer PCB with copper limited to solder pads 165 C/W *Additional thermal information available on Allegro Web site. Maximum Allowable VCC (V) Power Derating Curve 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 VCC(max) 2-layer PCB, Package LH (RJA = 110 C/W) 1-layer PCB, Package UA (RJA = 165 C/W) 1-layer PCB, Package LH (RJA = 228 C/W) 20 40 60 80 100 VCC(min) 120 140 160 180 Temperature (C) Power Dissipation, PD (m W) Power Dissipation versus Ambient Temperature 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 2l (R aye rP J C A = 11 B, P 0 ac 1-la C/ ka W (R yer PC ) ge L JA = B H 165 , Pac C/ kage W) UA 1-lay er P (R CB, JA = 228 Packag C/W e LH ) 20 40 60 80 100 120 Temperature (C) 140 160 180 Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 6 Chopper-Stabilized Hall Effect Latch A3282 Functional Description Operation The output of these devices switches low (turns on) when a magnetic field perpendicular to the Hall element exceeds the operate point threshold, BOP. After turn-on, the output voltage is VOUT(SAT). The output transistor is capable of sinking current up to the short circuit current limit, IOM, which is a minimum of 30 mA. Note that the device latches, that is, a south pole of sufficient strength towards the branded surface of the device turns the device on. The device remains on if the south pole is removed. When the magnetic field is reduced below the release point, BRP , the device output turns off (goes high). The difference in the magnetic operate and release points is the hysteresis, BHYS , of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. Powering-on the device in the hysteresis region (less than BOP and higher than BRP) allows an indeterminate output state. The correct state is attained after the first excursion beyond BOP or BRP . Applications It is strongly recommended that an external bypass capacitor be connected (in close proximity to the Hall element) between the supply and ground of the device to reduce both external noise and noise generated by the chopper stabilization technique. As is shown in Panel B of figure 1, a 0.1F capacitor is typical. Extensive applications information on magnets and Hall-effect devices is available in: * Hall-Effect IC Applications Guide, AN27701, * Hall-Effect Devices: Gluing, Potting, Encapsulating, Lead Welding and Lead Forming, AN27703.1 * Soldering Methods for Allegro's Products - SMT and ThroughHole, AN26009 All are provided in Allegro Electronic Data Book, AMS-702 and the Allegro Web site: www.allegromicro.com (B) (A) VS V+ VOUT VCC Switch to Low Switch to High VCC CBYP 0.1 F VOUT(SAT) 0 BOP B- BRP 0 A3282 RLOAD VOUT Output GND B+ BHYS Figure 1: Switching Behavior of Latches. In Panel A, on the horizontal axis, the B+ direction indicates increasing south polarity magnetic field strength, and the B- direction indicates decreasing south polarity field strength (including the case of increasing north polarity). This behavior can be exhibited when using a circuit such as that shown in panel B. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 7 Chopper-Stabilized Hall Effect Latch A3282 Chopper Stabilization Technique When using Hall-effect technology, a limiting factor for switchpoint accuracy is the small signal voltage developed across the Hall element. This voltage is disproportionally small relative to the offset that can be produced at the output of the Hall element. This makes it difficult to process the signal while maintaining an accurate, reliable output over the specified operating temperature and voltage ranges. Chopper stabilization is a unique approach used to minimize Hall offset on the chip. The patented Allegro technique, namely Dynamic Quadrature Offset Cancellation, removes key sources of the output drift induced by thermal and mechanical stresses. This offset reduction technique is based on a signal modulationdemodulation process. The undesired offset signal is separated from the magnetic-field-induced signal in the frequency domain, through modulation. The subsequent demodulation acts as a modulation process for the offset, causing the magnetic-fieldinduced signal to recover its original spectrum at baseband, while the dc offset becomes a high-frequency signal. The magnetic-field-induced signal then can pass through a low-pass filter, while the modulated dc offset is suppressed. This configuration is illustrated in figure 2. The chopper stabilization technique uses a 200 kHz highfrequency clock. For demodulation process, a sample and hold technique is used, where the sampling is performed at twice the chopper frequency (400 kHz). This high-frequency operation allows a greater sampling rate, which results in higher accuracy and faster signal-processing capability. This approach desensitizes the chip to the effects of thermal and mechanical stresses, and produces devices that have extremely stable quiescent Hall output voltages and precise recoverability after temperature cycling. This technique is made possible through the use of a BiCMOS process, which allows the use of low-offset, low-noise amplifiers in combination with high-density logic integration and sample-and-hold circuits. The repeatability of magnetic-field-induced switching is affected slightly by a chopper technique. However, the Allegro highfrequency chopping approach minimizes the affect of jitter and makes it imperceptible in most applications. Applications that are more likely to be sensitive to such degradation are those requiring precise sensing of alternating magnetic fields; for example, speed sensing of ring-magnet targets. For such applications, Allegro recommends its digital device families with lower sensitivity to jitter. For more information on those devices, contact your Allegro sales representative. Regulator Amp Low-Pass Filter Hall Element Sample and Hold Clock/Logic Figure 2. Chopper Stabilization Circuit (Dynamic Quadrature Offset Cancellation) Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 8 Chopper-Stabilized Hall Effect Latch A3282 Power Derating The device must be operated below the maximum junction temperature of the device, TJ(max). Under certain combinations of peak conditions, reliable operation may require derating supplied power or improving the heat dissipation properties of the application. This section presents a procedure for correlating factors affecting operating TJ. (Thermal data is also available on the Allegro MicroSystems Web site.) The Package Thermal Resistance, RJA, is a figure of merit summarizing the ability of the application and the device to dissipate heat from the junction (die), through all paths to the ambient air. Its primary component is the Effective Thermal Conductivity, K, of the printed circuit board, including adjacent devices and traces. Radiation from the die through the device case, RJC, is relatively small component of RJA. Ambient air temperature, TA, and air motion are significant external factors, damped by overmolding. The effect of varying power levels (Power Dissipation, PD), can be estimated. The following formulas represent the fundamental relationships used to estimate TJ, at PD. PD = VIN x IIN (1) T = PD x RJA (2) TJ = TA + T Example: Reliability for VCC at TA = 150C, package LH, using a low-K PCB. Observe the worst-case ratings for the device, specifically: RJA = 228 C/W, TJ(max) = 165C, VCC(max) = 24 V, and ICC(max) = 5 mA. Calculate the maximum allowable power level, PD(max). First, invert equation 3: Tmax = TJ(max) - TA = 165 C - 150 C = 15 C This provides the allowable increase to TJ resulting from internal power dissipation. Then, invert equation 2: PD(max) = Tmax / RJA = 15C / 228 C/W = 66 mW Finally, invert equation 1 with respect to voltage: VCC(est) = PD(max) / ICC(max) = 66 mW / 5 mA = 13 V The result indicates that, at TA, the application and device can dissipate adequate amounts of heat at voltages VCC(est). Compare VCC(est) to VCC(max). If VCC(est) VCC(max), then reliable operation between VCC(est) and VCC(max) requires enhanced RJA. If VCC(est) VCC(max), then operation between VCC(est) and VCC(max) is reliable under these conditions. (3) For example, given common conditions such as: TA= 25C, VCC = 12 V, ICC = 1.5 mA, and RJA = 165 C/W, then: PD = VCC x ICC = 12 V x 1.5 mA = 18 mW T = PD x RJA = 18 mW x 165 C/W = 3C TJ = TA + T = 25C + 3C = 28C A worst-case estimate, PD(max), represents the maximum allowable power level (VCC(max), ICC(max)), without exceeding TJ(max), at a selected RJA and TA. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 9 Chopper-Stabilized Hall Effect Latch A3282 Package LH, 3-Pin SOT23-W +0.12 2.98 -0.08 1.49 D 44 3 A +0.020 0.180-0.053 0.96 D +0.10 2.90 -0.20 +0.19 1.91 -0.06 2.40 0.70 D 0.25 MIN 1.00 2 1 0.55 REF 0.25 0.95 Seating Plane Gauge Plane B PCB Layout Reference View Branded Face 8X 10 REF 1.00 0.13 +0.10 0.05 -0.05 0.95 0.40 0.10 NNT 1 C N = Last two digits of device part number T = Temperature code For Reference Only; not for tooling use (reference dwg. 802840) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Active Area Depth, 0.28 mm REF B Reference land pattern layout All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances C Branding scale and appearance at supplier discretion D Hall element, not to scale Standard Branding Reference View Pin-out Drawings Package LH Package UA 3 1 2 1 2 3 Terminal List Name Description Number Package LH Package UA Connects power supply to chip 1 1 VOUT Output from circuit 2 3 GND Ground 3 2 VCC Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 10 Chopper-Stabilized Hall Effect Latch A3282 Package UA, 3-Pin SIP +0.08 4.09 -0.05 45 B C E 2.04 1.52 0.5 1.44 E Mold Ejector Pin Indent +0.08 3.02 -0.05 E Branded Face 45 1 2.16 MAX D Standard Branding Reference View = Supplier emblem N = Last two digits of device part number T = Temperature code 0.79 REF A 0.51 REF NNT 1 2 3 +0.03 0.41 -0.06 15.75 0.51 For Reference Only; not for tooling use (reference DWG-9049) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Dambar removal protrusion (6X) B Gate burr area C Active Area Depth, 0.50 mm REF +0.05 0.43 -0.07 D Branding scale and appearance at supplier discretion E Hall element, not to scale 1.27 NOM Copyright (c)2005-2009, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro's products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 11