TS51111 High Efficiency Synchronous Rectifier and Charging IC for Wireless Power Applications TRIUNE PRODUCTS Features Description * * * * * * * * * * * * * * * * The TS51111 is a fully-integrated synchronous rectifier for wireless charging applications with additional integrated components to minimize system BOM. High efficiency synchronous rectification of AC input Supports both Direct and Indirect Charging applications Supports WPC Qi(R) compliant and non-compliant systems Low Rds-on rectifier switches High voltage input for higher power systems Up to 20W+ Output >98% efficiency at high currents Integrated switches for load modulation Integrated switch for battery disconnect Integrated precharge current source 50mA output low Iq LDO Analog mux for ADC sensing Supply Under Voltage Lockout Low external component count Ultra-low standby quiescent current Junction operating temperature -40C to 125C Applications * * * * * * * Cell Phones and Smart Phones Tablet Computers eReaders Laptop Computers Small Digital Cameras Portable Video Recorders Wireless charging for portable devices TS51111 Final Datasheet April 17, 2015 Rev 2.2 The TS51111 includes a high efficiency synchronous rectifier to convert the input AC power signal to a DC output level for battery charging. The device supports both direct battery charging and indirect power applications. Low Rds-on switches minimize power dissipation. High voltage input capability allows for simple and robust secondary side charger implementation. An integrated switch provides the battery charging path and combined with the rectifier provides back feed protection to the AC inputs. A precharge current source is also included for low battery voltage precharge operation. Communication capability is achieved using integrated high voltage switches. The TS51111 includes several additional modules to allow simple integration into wireless power systems. Integrated resistor dividers with zero-current off-mode allow external ADC measurement of PDC, PACKP, USB and thermistor voltages. High voltage switches are included for communication modulation. Power to an external controller is provided through an integrated LDO. The ultra-low quiescent current regulator can supply high output currents at low dropout with minimal current draw from the battery. Available in a 45 pin WCSP and 36 pin 6x6 QFN package. www.semtech.com 1 of 22 Semtech Proprietary & Confidential Pinout (WCSP) (Top View) TS51111 Final Datasheet April 17, 2015 Rev 2.2 A1 A2 A3 A4 A5 SCL AMUX AGND MOD1 MOD2 B1 B2 B3 B4 B5 SDA VREF PACKN USB EN_MOD C1 C2 C3 C4 C5 VCORE THERM UART TXD PACKS D4 D5 D1 D2 D3 BST1 OVP RXD E1 E2 E3 E4 E5 BST2 PDC PDC PDC PDC F1 F2 F3 F4 F5 VAC2 VAC2 VAC2 VAC1 G1 G2 G3 G4 G5 VACDET PGND PGND PGND PGND H1 H2 H3 H4 H5 VAC2 VAC2 VAC2 VAC1 VAC1 I1 PDC I2 PDC I3 PDC I4 I5 PDC PDC www.semtech.com PACKP PACKP VAC1 2 of 22 Semtech Proprietary & Confidential Pin Description (WCSP) Pin # Pin Name Pin Function Description A1 SCL I2C Clock I2C clock A2 AMUX Analog Sense Analog MUX output A3 AGND Analog Ground Quiet ground connection A4 MOD1 MOD cap connection Pulldown for capacitive modulation A5 MOD2 MOD cap connection Pulldown for capacitive modulation B1 SDA I2C Data I2C data B2 VREF Vref Output ADC reference output B3 PACKN PACKN Sense Battery negative terminal B4 USB USB Supply USB supply and detection input B5 EN_MOD Enable Modulation Enables modulation switches C1 VCORE VCORE LDO LDO output C2 THERM Thermistor Drive Thermistor drive C3 UART UART Bus UART bus C4 TXD UART TX UART Tx C5 PACKS Output Current Sense Sense node for output current D1 BST1 BST cap Boost capacitor connection for HS FETs D2 OVP OV Clamp Overvoltage pulldown clamp D3 RXD UART RX UART Rx D4, D5 PACKP Battery Connection Battery positive terminal E1 BST2 BST cap Boost capacitor connection for HS FETs E2-5 PDC Input power Rectified input signal F1-F3 VAC2 Coil input AC power input from coil F4, F5 VAC1 Coil input AC power input from coil G1 VACDET VAC Detect Indicates incoming power to external micro G2-5 PGND Power gnd GND for synchronous rectifier and charging path H1-H3 VAC2 Coil input AC power input from coil H4, H5 VAC1 Coil input AC power input from coil I1-5 PDC Rectified voltage Filter capacitor connection for rectified voltage TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 3 of 22 Semtech Proprietary & Confidential Pinout (QFN) (Top View) TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 4 of 22 Semtech Proprietary & Confidential Pin Description (QFN) Pin # Pin Name Pin Function Description 1 EN_MOD Enable Modulation Enables modulation switches 2 TXD UART TX UART Tx 3 RXD UART RX UART Rx 4 PACKS Output Current Sense Sense node for output current 5 PACKP_K PACKP Kelvin PACKP Kelvin 6 PACKP Battery Connection Battery positive terminal 7, 13-14 PDC Rectified voltage Filter capacitor connection for rectified voltage 8, 11-12 VAC1 Coil input AC power input from coil 9-10, 17-18 PGND Power gnd GND for synchronous rectifier and charging path 15-16, 20 VAC2 Coil input AC power input from coil 19 VAC_DET VAC Detect Indicates incoming power to external micro 21 OVP OV Clamp Overvoltage pulldown clamp 22 BST2 BST cap Boost capacitor connection for HS FETs 23 BST1 BST cap Boost capacitor connection for HS FETs 24 VCORE VCORE LDO LDO output 25 THERM Thermistor Drive Thermistor drive 26 SDA I2C Data I2C data 27 SCL I2C Clock I2C clock 28 NC No Connect No Connect 29 VREF Vref Output ADC reference output 30 AMUX Analog Sense Analog MUX output 31 UART UART Bus UART bus 32 PACKN PACKN Sense Battery negative terminal 33 AGND Analog Ground Quiet ground connection 34 MOD1 MOD cap connection Pulldown for capacitive modulation 35 MOD2 MOD cap connection Pulldown for capacitive modulation 36 USB USB Supply USB supply and detection input TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 5 of 22 Semtech Proprietary & Confidential Functional Block Diagram OVP Detect EN_SW VCORE REG BST1 VAC1 ~ PACKP + EN_PRE COUT MOD1 CS PACKPSNS Synchronous Rectifier CR CD IOSENSE A IBSENSE A PACKN MOD2 CB2 CCORE PreDrive BATT CD CB1 VCORE USB PDC TS51111 OVP CIN VCORE PGND - ~ VAC2 AGND EN_THERM A2D Rs VREF THERM BST2 UART PreDrive TxD EN_MOD SDA Digital Control PACKP_DIV PDC_DIV IBSENSE PACK+ RxD IOSENSE TEMP VREF VAC_DET PACK- VREF AMUX PACK- AGND SCL PACK- CREF Figure 1: TS51111 Block Diagram TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 6 of 22 Semtech Proprietary & Confidential Absolute Maximum Rating Over operating free-air temperature range unless otherwise noted(1, 2, 3) Parameter Value Unit -0.3 to 22 V -0.3 to (VAC + 5.5) V VCORE, TX, RX, UART, PACKP, SCL, SDA, VAC_DET, VREF, AMUX, VCORE, USB -0.3 to 5.5 V Operating Junction Temperature Range, TJ -40 to 125 C Storage Temperature Range, TSTG -65 to 150 C 2k V Electrostatic Discharge - Machine Model +/-200 V Lead Temperature (soldering, 10 seconds) 260 C VAC1, VAC2, PDC, MOD1, MOD2, OVP BST1, BST2 Electrostatic Discharge - Human Body Model Notes: (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to network ground terminal. (3) ESD testing is performed according to the respective JESD22 JEDEC standard. Recommended Operating Conditions Symbol Parameter VACPP Min Typ Input Operating Voltage FVAC Max Unit 20 V Input Operating Frequency 100 210 kHz PACKP Battery input when externally driven 2.5 5.5 V LIN Inductor (measured on charging mat) 14* uH CR Parallel resonant capacitor 1.8* nF CS Series resonant capacitor 183* nF CO Modulation capacitors 22 nF COUT Output capacitor 0.8 1 uF CCORE LDO decoupling capacitor 8 10 uF CB1, CB2 Rectifier boost capacitors 200 220 Synchronous rectifier / PDC decoupling capacitor 10 20 uF Analog mux decoupling capacitor 1 2 nF VREF decoupling capacitor 80 100 TA Operating Free Air Temperature TJ Operating Junction Temperature CIN CAMUX CREF 240 nF 120 nF -40 85 C -40 125 C * Exact values of the resonant capacitors and inductor will depend on the specific system configuration. TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 7 of 22 Semtech Proprietary & Confidential Thermal Characteristics Symbol JA Parameter Value Units 36QFN Thermal Resistance Junction to Air (Note 1) 32 C/W Note 1: Assumes 3.917 x 3.917 in2 area of 1 oz copper, 4 layer PCB, 4 thermal vias under PAD, and 25C ambient temperature. Characteristics Electrical Characteristics, TJ = -40C to 85C, PDC = PACKP = 4.2V (unless otherwise noted) Symbol Parameter IQ IQ,Standby,LPM IQ,Disable Condition Quiescent Current in Disable (Direct Charge, Low Power Mode disabled) Current from PACKP, ILDO = 0, EN_ VREF = EN_SW = EN_PRE = 0 Current from PACKP, ILDO = 0, EN_ VREF = EN_SW = EN_PRE = 0 PACKP UVLO PACKP Rising Quiescent Current in Low Power Mode Min Typ Max Unit 20 30 uA 2 uA 2.1 V PACKP UVLO Hysteresis 400 mV TSW-ON Delay from EN_SW to switch ON 200 us TSW-OFF Delay from EN_SW to switch OFF 100 ns UVLO VUVLO-PACK_P HYSTUVLO-PACK_P PDC-PACKP Pass Device IPRECHARGE TCPRECHARGE ILIMIT Precharge Current Relative to set point T = 25C; PDC = 3.5V; PACKP = 2.7V Precharge Current Temperature Coefficient 25C to 85C Current Limit At 3.2 A setting INOM -20% 2.2 INOM INOM +20% -0.3 %/C 3.2 A UART TRX Delay from UART to RX 0.7 us T TX Delay from TX to UART 0.6 us UART threshold 0.8 V TX threshold 0.8 V RX Switch Resistance 10 V T,UART V T,TX Rdson,RX SDA / SCl / EN_MOD Digital Inputs VIH VCORE = 1.5V Voltage Rising 0.875 V VIL VCORE = 1.5V Voltage Falling 0.465 V VIH VCORE = 1.8V Voltage Rising 1.01 V VIL VCORE = 1.8V Voltage Falling 0.525 V VIH VCORE = 2.5V Voltage Rising 1.25 V VIL VCORE = 2.5V Voltage Falling 0.665 V VIH VCORE = 3.3V Voltage Rising 1.47 V VIL VCORE = 3.3V Voltage Falling 0.825 V RIN Pin input impedance Resistance to GND 1M TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 8 of 22 Semtech Proprietary & Confidential Electrical Characteristics, TJ = -40C to 85C, PDC = PACKP = 4.2V (unless otherwise noted) Symbol Parameter Condition Min Typ Max Unit VOH Output high voltage Totem-pole configuration only. 100uA load. VCORE100mV V VOL Output low voltage Totem-pole or open-drain configurations. 100uA load. 100 mV IOFF Output leakage Output leakage in open-drain off-state. Switch Resistance Output resistance to GND in open-drain on-state. VAC Detect Rdson,VAC_DETECT 0.1 10 uA VREF CVREF VREF decoupling capacitor VVREF VREF voltage RPDC-DIV PDC_DIV ratio RPACKP-DIV RUSB-DIV RTHERM-DIV IQ,VREF TEN-VREF 80 100 120 nF T = 0 to 85 C, IOUT 0mA to 2mA 1.988 2.0 2.012 V T = 0 to 85 C, PDC_DIV_SEL = 0 0.048 0.05 0.052 V/V T = 0 to 85 C, PDC_DIV_SEL = 1 0.198 0.2 0.202 V/V PACKP_DIV ratio T = 0 to 85 C 0.198 0.2 0.202 V/V USB_DIV ratio T = 0 to 85 C 0.198 0.2 0.202 V/V THERM_DIV ratio T = 0 to 85 C 0.495 0.5 0.505 V/V VREF quiescent current PACKP current if VREF enabled 300 uA VREF enable time Delay from EN_VREF to VREF available 3.2 us 3 us 0.7 us MOD TMOD-ON TMOD-OFF IQ,MOD Rdson,MOD EN_MOD to switches ON delay EN_MOD to switches OFF delay MOD block quiescent current Current from PACKP when MOD switches closed. EN_MOD hi. EN_ VREF = EN_SE = EN_PRE = lo 100 uA MOD Switch Resistance MOD1 to MOD2 3 VCORE voltage PACKP = 4.2V 3.3 V Dropout voltage PACKP = 2.3V, IVCORE=1mA Output current PACKP=4.2V, VCORE = 0.9*VCORENOM Low Power LDO VCORENOM VDropout Iout CCORE LDO Decoupling Capacitor 0.8 100 mV 10 50 mA 1 1.2 uF OVP VOVP Rdson,OVP TS51111 Final Datasheet April 17, 2015 OVP Threshold 21 V OVP Switch Resistance 2 Rev 2.2 www.semtech.com 9 of 22 Semtech Proprietary & Confidential Electrical Characteristics, TJ = -40C to 85C, PDC = PACKP = 4.2V (unless otherwise noted) Symbol Parameter Condition Min Typ Max Unit Temperature Sensing THYST Over-temperature shutdown threshold Over-temperature shutdown hysteresis V TSENSE Temperature Sensor Voltage 25C TCV TSENSE Temperature Coefficient 0C to 85C TSHUTDOWN Temperature rising 0.725 170 C 10 C .75 0.775 2.4 V mV/C Current Sensing PACKN - AGND 10mV to 20mV; Gain setting = 20 PACKP - PACKS 10mV to 20mV Gain setting = 20; PACKP = 5V PACKN - AGND = 20mV; Gain setting = 20; 25C IBSENSE GAIN Battery current sense amp gain IOSENSE GAIN Output current sense amp gain IBSENSE VOFFSET Battery current sense amp offset IOSENSE VOFFSET Output current sense amp offset VIB,MAX Full range amp output 750 mV VIO,MAX Full range amp output 750 mV VCORE100mV V 100 mV PACKP - PACKS = 20mV Gain = 20; PACKP = 5V; 25C 19.6 20 20.4 V/V 19.6 20 20.4 V/V -0.5 0 0.5 mV -0.5 0 0.5 mV VAC Detect VOH Output high voltage VOL Output low voltage IOFF Output leakage Rdson,VAC_DETECT Switch Resistance Totem-pole configuration only. 100uA load. Totem-pole or open-drain configurations. 100uA load. Output leakage in open-drain off-state. Output resistance to GND in open-drain on-state. 0.1 10 uA Functional Description Synchronous Rectifier The bridge rectifier in the TS51111 has a synchronous controller which shunts the forward bias of the bridge diodes. This allows the TS51111 to provide currents of up to 3.2A to be efficiently transferred without significant power dissipation. The primary side of the bridge can stand-off up to 20V. On the secondary side, a capacitive load on the PDC pin can be used to help attenuate the voltage signal observed on both sides of the bridge rectifier. External boost capacitors CB1 and CB2 allow use of efficient high side nmos switches. The rectifier is disabled by default and will remain in an asynchronous mode until incoming power is detected or EN_SW or EN_PRE are asserted. In asynchronous mode, the bridge FETs will not switch and voltage rectification will occur through the parasitic diodes of the FETs. In this mode, current draw in the IC is minimal. TS51111 Final Datasheet April 17, 2015 Rev 2.2 The bridge can be forced into asynchronous (no FET switching) or half synchronous (LS FET only switching) operation at any time using the CNFG register using the ASYNC or HSYNC bits respectively. This can be used to improve efficiency at light loads where the switching losses of the bridge would exceed the conduction losses of the parasitic diodes. Load Switch / Blocking FET The integrated low impedance blocking switch provides a direct charging path to the battery and disconnects the output from the rectified signal until the system has been successfully configured. Control of the switch is achieved through the I2C interface. An integrated charge pump guarantees maximum drive strength is available for the FET when operated as a switch. When hard switched, gate drive is slewed slowly to limit inrush current from the PDC cap to the battery. www.semtech.com 10 of 22 Semtech Proprietary & Confidential Functional Description (continued) The load switch can be reconfigured to operate as a linear regulator (see Charge Termination section below). When enabled, the output will soft-start to limit inrush current. In linear regulation mode, the PDC voltage must be regulated close to the dropout voltage to limit power dissipation in the IC. In linear regulation mode, a configurable, integrated current limit circuit provides fault protection to the system. At the maximum setting, current limit is disabled. If the output current hits the current limit threshold, the device will automatically limit the output current and set the FAULT register ILIM bit. In this condition, the PDC voltage will build up and must be managed through the system loop by reducing the transmitted power. If the transmitted power is not reduced, the TS51111 power dissipation will increase and eventually force a thermal shutdown of the part. Current limit in direct charge mode is not integrated but can be easily implemented by monitoring device output current using the integrated current sense amplifiers. Precharge In low battery conditions, an integrated precharge current source can be used to slowly charge the battery with a controlled DC current source. The precharge current source is controlled using the I2C interface. The precharge current has a negative temperature coefficient to mitigate temperature rise of the TS51111 during pre-charge. The level of the Precharge current can be set according to the table below. PRESET<2:0> Precharge Current (mA) 000 30 001 40 010 50 011 60 100 70 101 80 110 90 111 100 Low Power Mode ILIMSET<3:0> Current Limit Typical (mA) 0000 350 0001 600 0010 850 0011 1100 0100 1350 0101 1600 0110 1850 0111 2100 Current Sense Amps 1000 2350 1001 2600 1010 2850 1011 3100 1100 3350 1101 3600 1110 3850 1111 Disable ILIM Two current sense amplifiers are included to allow for accurate battery charge current and received current measurements. The IBSENSE amplifier provides an output that is proportional to the sense voltage on the PACKN pin when a sense resistor is placed between PACKN and ground. The IOSENSE amplifier will measure the differential voltage across the sense resistor placed in series with the output current. This measurement is an indicator of the power received by the TS51111. The IOSENSE output is not valid when the device is in current limit. The system should check the FAULT register periodically to ensure the device is in a proper operating state without any faults. Both amplifiers have a configurable gain set by the ISET register. The gains are configurable from 10x to 80x. TS51111 Final Datasheet April 17, 2015 Rev 2.2 The TS51111 supports a low-power mode when connected directly to a battery. In this mode, the ultra-low quiescent current LDO output is enabled to power an external microcontroller and the power consumption of the rest of the IC is minimized. In this mode, the TS51111 still supports UART level translation to the microcontroller. The part will automatically switch to normal operation when incoming power is detected. www.semtech.com 11 of 22 Semtech Proprietary & Confidential USB Functional Description (continued) The TS51111 will automatically detect the presence of a voltage applied to the USB pin. If the USBCTRL bit is set low and a voltage is applied to the USB pin, the part will respond by disabling all charging paths to the battery and switching the LDO power input from the battery to the USB. If the USBCTRL bit is set hi, the part will not automatically disable charging or switch the LDO power input. The USBCTRL bit is programmed in Non-Volatile Memory (NVM) during manufacturing and is not user configurable. In either condition, the USBDET bit in the FAULT register will be set. When USB power is removed, the part will return to normal operation. LDO VAC Detect The presence of incoming power on the coils will be indicated by the TS51111 by asserting the VAC_DET output pin. The pin will be de-asserted when incoming power is removed. The VAC_DETECT output can be configured as open-drain with an external resistor pull-up or as a totem pole with a VCORE high level. This is set using the VAC_CNFG bit with hi for open-drain and low for totem-pole. UART UART level translators are included to facilitate communication between system components. The level shifters will translate voltage levels from VCORE for the system microprocessor to PACKP for a separate system. The TS51111 LDO supports a variety of system configurations. An on-chip ultra-low Iq LDO is provided for powering external system components when a battery or USB supply is available. The LDO is designed to operating with minimum quiescent but can still deliver high output current at low dropout voltage. Integrated current limit provides additional protection. VREF If an external USB power supply is available, the LDO will draw its input power from the USB pin instead of from the battery. In the event that neither an external USB supply nor an external battery is available, the LDO will automatically powerup of the rectified voltage when incoming power is detected and provide power to an external microcontroller. An on-board over-voltage sensor on the PDC signal is available if additional external over-voltage protection is needed. In an over-voltage condition, the OVP FET is active to provide a low impedance path to ground on the OVP pin. In addition, the OVP FET can be forced on using the register bit. This can be used to provide an additional load on PDC if required. In an OVP condition, the OVP bit of the FAULT register will be set hi. To support multiple possible external microcontrollers, the internal LDO has a configurable output voltage. The voltage is set according to the following table. The LDOSET<1:0> bits are programmed in Non-Volatile Memory (NVM) during manufacturing and are not user configurable. LDOSET<1:0> VCORE (V) 00 1.5 01 1.8 10 2.5 11 3.3 (default) TS51111 Final Datasheet April 17, 2015 Rev 2.2 An internal high-accuracy VREF circuit provides a precision reference for external analog-to-digital converters. Integrated voltage dividers provide sense voltages for external ADC measurement. The VREF circuit is enabled using the EN_VREF bit and will not draw any current when not active. OVP Temperature Sensing The die temperature of the TS51111 is measured using an onboard temperature sensor. The output of the temperature sensor is available on the AMUX pin. If the temperature of the TS51111 exceeds the TSD threshold, all high current operations will be disabled until the die temperature reaches a safe level. Temperature hysteresis prevents rapid entering and exiting of the over-temperature state. In thermal shutdown, the load switch, precharge current, and synchronous rectifier are disabled. All other functions including OVP and MOD will still be available. When the TSD threshold is hit, the TSD bit in the FAULT register will be set. www.semtech.com 12 of 22 Semtech Proprietary & Confidential Charge Termination Functional Description (continued) To allow for accurate charge termination in a charging application, the TS51111 load switch can be reconfigured to operate as a voltage regulator. In this mode, the switch source voltage will be regulated to the voltage set by the VOUTSET<6:0> bits. The switch is put into this mode by asserting the EN_TOP bit of the configuration register. Available voltage settings and the corresponding codes are shown. To support indirect charge applications, the EN_TOP and IND_SET bits must both be set hi. The output voltage will still be determined by the VOUTSET<6:0> bits. The VOUT setpoints are 3.0V to 5.54V in 20mV steps. In addition, VOUTSET<6:0>=0x64 will select a 5.0V setpoint. Thermistor Driver An integrated thermistor driver allows system temperature measurement. When enabled, the thermistor drive will drive the VREF voltage onto the THERM pin. When disabled, the THERM pin will be high impedance to allow external drive of the same thermistor. In the automatic mode, the thermistor driver is enabled whenever battery charging is enabled. This is whenever EN_SW or EN_PRE are active. The voltage on the THERM pin can be measured using the internal voltage divider and will be visible on the AMUX pin. AMUX To reduce the number of connections required between the microprocessor and the TS51111, all analog outputs from the TS51111 are measured from the same analog pin and selectable via the AMUX register. Signals on the AMUX pin are buffered using an internal unity gain amplifier. When unselected, the AMUX pin will be high impedance. AMUX<2:0> Analog Signal 000 ---- 001 PDC_DIV 010 IOSENSE 011 IBSENSE 100 TEMP 101 PACKP_DIV 110 USB_DIV 111 THERM_DIV TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com TCTRL<1:0> Thermistor Operation 00 Disable 01 Enable 10 Auto 11 13 of 22 Semtech Proprietary & Confidential Control Registers REG R/W Description LSON R/W Forces on both LS FETs when hi. Allows normal synchronous rectifier operation when lo. VAC_CONFIG R/W Configures VAC_DET output pin behavior. Totem pole configuration when hi. Open-drain configuration when lo. HSYNC R/W Forces half-synchronous rectifier operation (LS FET only switching) when lo. Allows synchronous rectifier operation when hi. (ASYNC has priority when lo) ASYNC R/W Disables synchronous rectifier operation when lo. Allows synchronous rectifier operation when hi. (Has priority over HSYNC when lo) EN_VREF R/W Enables VREF reference for external analog-to-digital converters when hi. Disables VREF reference when lo. EN_TOP, EN_SW R/W EN_TOP = 0, EN_SW = 0 Load switch is disabled EN_TOP = 1, EN_SW = x Load switch is enabled as an LDO EN_TOP = 0, EN_SW = 1 Load switch is enabled as a switch EN_PRE R/W Enables the precharge current source when hi. Current source is disabled when lo. IND_SET R/W Configures part for indirect charge operation when hi. Configures part for topoff or direct charge operation when lo. PACKP_LD_EN R/W Enables an internal 500 Ohm resistive load on PACKP when hi. Load is disconnected when lo. OVP_ON R/W Forces the OVP FET to turn on as defined by the OVP_CS bit when hi. OVP is triggered only by high voltage on PDC when lo. EN_MOD R/W Turns on the MOD FETs when hi. Turns off the MOD FETs when lo. PRESET <2:0> R/W Sets the level of the pre-charge current AMUX <2:0> R/W Configures measurement point for AMUX pin PDC_DIV_SEL R/W Changes the ratio of the PDC divider ILIMSET <3:0> R/W Configures the indirect charging internal current limit TCTRL <1:0> R/W Configures the behavior of the Thermistor driver (THERM pin) DIS_VREF R/W Force the VREF output off OVP_CS R/W Configures the OVP FET as 30mA current source (hi) or a switch (lo) AMUX_10K_PLDN R/W Enable a 10K pull down load resistor on AMUX buffer VCORE_indset R/W Optimizes VCORE regulator for indirect charge mode. HI_R R/W Increases the Ron for HS switches in the synchronous rectifier IB <2:0> R/W Configures the gain of the IBSENSE amplifier (000=10X, 001=20X,...111=80X) IO <2:0> R/W Configures the gain of the IOSENSE amplifier (000=10X, 001=20X,...111=80X) VOUTSET <6:0> R/W Configures the VOUT voltage setting for charge termination PACKP_OVP R On-die over-voltage sensor status bit. Bit is hi during a PACKP over-voltage condition. OVP R On-die over-voltage sensor status bit. Bit is hi during a PDC over-voltage condition. TSD R On-die thermal sensor over-temperature status bit. Bit is hi during an over-temperature condition. USBDET R Status bit that indicates voltage applied to USB pin. Bit is hi when USB voltage is detected. ILIM R On-die current limit status bit. Bit is hi when current-limit is active. TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 14 of 22 Semtech Proprietary & Confidential Register Map REG AD R/W CNFG 0x0 R/W B7 0x00 B6 B5 B4 B3 B2 B1 B0 VAC_CNFG HSYNC ASYNC EN_VREF EN_TOP EN_PRE EN_SW IND_SET PACKP_LD_ EN OVP_ON EN_MOD PRESET<2> PRESET<1> PRESET<0> CNFG2 0x1 R/W 0x00 PRESET 0x2 R/W 0x00 AMUX 0x3 R/W 0x00 PDC_DIV_ SEL AMUX<2> AMUX<1> AMUX<0> 0x4 R/W 0x00 ILIMSET<3> ILIMSET<2> ILIMSET<1> ILIMSET<0> TCTRL 0x5 R/W 0x00 ISET 0x6 R/W 0x00 0x7 R/W 0x00 0x8 R -- FAULT HI_R VCORE_ indset AMUX_10K_ PLDN EN_OVP_CS DIS_VREF TCTRL<1> TCTRL<0> IB<2> IB<1> IB<0> IO<2> IO<1> IO<0> PACKP_OVP OVP TSD USBDET ILIM Device address is 0x48 I2C Interface Timing Requirements Symbol Parameter fscl Standard Mode Fast Mode(1) Max I2C clock frequency 0 100 tsch I2C clock high time 4 0.6 s tscl I C clock low time 4.7 1.3 s 2 Max 0 400 I C tolerable spike time 0 I2C serial data setup time 250 250 ns tsdh I2C serial data hold time 0 0 s 2 0 50 kHz tsds tsp (2) 50 Min Unit Min ns (2) I C input rise time 1000 300 ns ticf(2) I2C input fall time 300 300 ns tocf(2) I2C output fall time; 10 pF to 400 pF bus 300 300 ns tbuf I C bus free time between Stop and Start 4.7 tsts I C Start or repeated Start condition setup time tsth I2C Start or repeated Start condition hold time I C Stop condition setup time ticr tsps 2 2 2 (2) 2 1.3 s 4.7 0.6 s 4 0.6 s 4 0.6 s (1) The IC interface will operate in either standard or fast mode. (2) Parameters not tested in production. TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 15 of 22 Semtech Proprietary & Confidential Application Schematic 1 2 C2 VAC1 A 47nF 50V C10 68nF 50V C12 COIL AC AC 1 2 J2 C8 100pF 50V C9 1.8nF 50V VAC2 23 C1 100nF 50V 8 11 12 C7 22nF 50V 34 35 C11 22nF 50V 15 16 20 C13 100nF 50V 68nF 50V GND 22 31 2 3 EN_MOD 1 VACDET 19 AMUX 30 25 B SCL SDA 27 26 3 U1 BST1 USB VAC1 VAC1 VAC1 PDC PDC PDC MOD1 MOD2 OVP VAC2 VAC2 VAC2 PACKS PACKP_K PACKP BST2 36 USB 7 13 14 PDC 21 PACKN VACDET PAD PGND PGND PGND PGND THERM AMUX VCORE VREF NC SCL SDA AGND C4 10uF 25V C5 10uF 25V C6 10uF 25V 4 5 6 PACKP C14 10uF 6.3V UART TXD RXD EN_MOD C3 10uF 25V R4 100 4 32 37 9 10 17 18 24 29 28 R1 GND PACKS 0.020 C15 10uF 6.3V GND A D1 NP GND 1 2 J1 D2 5.6V GND AGND 33 C17 1uF 6.3V B GND VCORE VREF C16 10nF 10V Out GND VCORE GND AGND + - TP1 C18 100nF 10V TS51111_QFN36 AGND RESET TP2 DEBUG TP3 SCL TP4 SDA TP5 TP6 VACDET EN_MOD SCL SDA VREF AMUX VSS AGND GPIO4 GPIO5 18 19 7 RESET DEBUG 1 20 GPIO1 GPIO2 GPIO3 GPIO6 GPIO7 GPIO8 NRST DEBUG EN_LOAD LED 14 17 3 2 13 12 16 15 9 10 11 6 8 AGND VACDET EN_MOD SCL SDA VREF LEDR AMUX R2 C19 10K 2nF 10V LEDG LEDR PDC TP7 AMUX TP8 USB TP9 VAC1 TP10 C 1 4 VDD AGND D3 LEDG 2 C U2 3 5 4 VCORE TS81001-QFN R3 150 GND D D Title Size: TS51111 EVM WCSP package, no micro-vias Letter Date: 4/26/2013 1 2 Number: Revision:0.1 Time: 5:25:52 PM Sheet 1 of 1 3 4 Figure 2: TS51111 Wireless Receiver Application TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 16 of 22 Semtech Proprietary & Confidential Package Drawing (WCSP) Units Dimensions Limits MILLIMETERS MIN NOM MAX Number of Contacts N 45 Contact Pitch e 0.40 BSC Overall Height A 0.445 0.525 0.625 Standoff A1 0.12 0.20 0.30 Moldel Package Tickeness A2 - - 0.325 Overall Width E 2.195 - 2.200 Array Width E1 Overall Length D Array Length D1 Contact Diameter TS51111 Final Datasheet April 17, 2015 b Rev 2.2 1.60 BSC 3.795 - 3.800 3.20 BSC 0.250 www.semtech.com 0.265 0.280 17 of 22 Semtech Proprietary & Confidential Package Drawing (QFN) Units Dimensions Limits N e A A1 A3 D E2 E D2 b L K Number of Pins Pitch Overall Height Standoff Contact Thickness Overall Length Exposed Pad Width Overall Width Exposed Pad Length Contact Width Contact Length Contact-to-Exposed Pad TS51111 Final Datasheet April 17, 2015 Rev 2.2 MILLIMETERS MIN 4.30 NOM 36 0.50 BSC 0.90 0.02 0.20 REF 6.00 BSC 4.45 4.30 0.20 0.45 0.20 6.00 BSC 4.45 0.25 0.55 - 0.80 0.00 www.semtech.com MAX 1.00 0.05 4.55 4.55 0.30 0.65 - 18 of 22 Semtech Proprietary & Confidential Package Drawing (QFN) Units MILLIMETERS Dimensions Limits Contact Pitch Optional Center Pad Width Optional tenter Pad Length Contact Pad Spacing Contact Pad Spacing Contact Pad Width (X36) Contact Pad Length (X36) Distance Between Pads E W2 T2 C1 C2 X1 Y1 G MIN NOM MAX 0.15 0.50 BSC 6.00 6.00 - 4.45 4.45 0.35 0.65 - Notes: Dimensions and tolerancing per ASME Y14.5M BSC: Basic Dimension, Theorically exact value shown with tolerances. REF: Reference Dimension, usually with tolerance, for information only. TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 19 of 22 Semtech Proprietary & Confidential TS51111 Version 2.2 Package Marking (WCSP) ACKAGE TOP MARKING Legend: o Pin 1 Identifier Line 1 Marking: TS51111 Device identification Line 2 Marking: XXXXXX Lot number (2 - 9 digits) Line 3 Marking: Y Y = last digit of year M M = month (1=Jan, 2=Feb, 3=Mar ... A=Oct, B=Nov, C=Dec) TS5 Ve gend: Marking (QFN) AGE Package TOP MARKING o Pin 1 Identifier ne 1 Marking: TS51111 Device identification XXXXXX Y M Legend:(2 - 9 digits) Lot number Y Y = last digit of year M M = month (1=Jan, 2=Feb, 3=Mar ...A=Oct, A=Oct, B=Nov,B=Nov, C=Dec) C=Dec) ne 2 Marking: T S ne 3 Marking: 5 1 o 1 L 1 1 L S Line 1 Marking: TS Triune Systems Logo Y Y = last digit of year M M = month (1=Jan, 2=Feb, 3=Mar ... Line 2 Marking: 51111 Device identification Line 3 Marking: o Pin 1 Identifier LL LL = Last two whole (non-fractional) digits of lot number S Assembly Site Identifier : Marking: TS51111 Marking: Final Datasheet April 17, 2015 TS Triune Systems Logo Y Y = last digit of year M M = month (1=Jan, 2=Feb, 3=Mar ... A=Oct, B=Nov, C=Dec) Rev 2.2 51111 Device www.semtech.com identification o Pin 1 Identifier 20 of 22 Semtech Proprietary & Confidential Ordering Information Part Number Description TS51111-M22WCSR High Efficiency Wireless Power Receiver, WCSP Package TS51111-M22QFNR High Efficiency Wireless Power Receiver, QFN Package RoHS and Reach Compliance Triune Systems is fully committed to environmental quality. All Triune Systems materials and suppliers are fully compliant with RoHS (European Union Directive 2011/65/EU), REACH SVHC Chemical Restrictions (EC 1907/2006), IPC-1752 Level 3 materials declarations, and their subsequent amendments. Triune Systems maintains certified laboratory reports for all product materials, from all suppliers, which show full compliance to restrictions on the following: * * * * * * * * * * * * Cadmium (Cd) Chlorofluorocarbons (CFCs) Chlorinate Hydrocarbons (CHCs) Halons (Halogen free) Hexavalent Chromium (CrVI) Hydrobromofluorocarbons (HBFCs) Hydrochlorofluorocarbons (HCFCs) Lead (Pb) Mercury (Hg) Perfluorocarbons (PFCs) Polybrominated biphenyls (PBB) Polybrominated Diphenyl Ethers (PBDEs) TS51111 Final Datasheet April 17, 2015 Rev 2.2 www.semtech.com 21 of 22 Semtech Proprietary & Confidential IMPORTANT NOTICE Information relating to this product and the application or design described herein is believed to be reliable, however such information is provided as a guide only and Semtech assumes no liability for any errors in this document, or for the application or design described herein. Semtech reserves the right to make changes to the product or this document at any time without notice. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. Semtech warrants performance of its products to the specifications applicable at the time of sale, and all sales are made in accordance with Semtech's standard terms and conditions of sale. SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS, OR IN NUCLEAR APPLICATIONS IN WHICH THE FAILURE COULD BE REASONABLY EXPECTED TO RESULT IN PERSONAL INJURY, LOSS OF LIFE OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER'S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. The Semtech name and logo are registered trademarks of the Semtech Corporation. Triune Systems, L.L.C. is now a wholly-owned subsidiary of Semtech Corporation. The Triune Systems(R) name and logo, MPPT-liteTM, and nanoSmart(R) are trademarks of Triune Systems, LLC. in the U.S.A. All other trademarks and trade names mentioned may be marks and names of Semtech or their respective companies. Semtech reserves the right to make changes to, or discontinue any products described in this document without further notice. Semtech makes no warranty, representation or guarantee, express or implied, regarding the suitability of its products for any particular purpose. All rights reserved. (c) Semtech 2015 Contact Information Semtech Corporation 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111, Fax: (805) 498-3804 www.semtech.com TS51111 Final Datasheet April 17, 2015 Rev 2.2 22 of 22 Semtech Proprietary & Confidential