NOTE: This product has been replaced with UT28F256LVQLE
or SMD 5962-01517 device types 04 and 05.
2
Standard Products
UT28F256LVQL Radiation-Hardened 32K x 8 PROM
Data Sheet
June 2005
www.aeroflex.com/radhard
FEATURES
Programmable, read-only, asynchronous, radiation-
hardened, 32K x 8 memory
- Supported by industry standard programmer
65ns maximum address access time (-55 oC to
+125 oC)
Three-state data bus
Low operating and standby current
- Operating: 50.0mA maximum @15.4MHz
Derating: 1.7mA/MHz
- Standby: 1.0mA maximum (post-rad)
Radiation-hardened process and design; total dose
irradiation testing to MIL-STD-883, Method 1019
- Total dose: 100Krad to 1Megarad(Si)
- LETTH(0.25) ~ 40 MeV-cm2/mg
- SEL Immune >110 MeV-cm2/mg
- Saturated Cross Section cm2 per bit, 2E-6
- 4E-4 errors/device-day, Adams 90% geosynchronous
heavy ion
QML Q & V compliant part
- AC and DC testing at factory
No post-program conditioning required
Packaging options:
- 28-lead 50-mil center flatpack (0.490 x 0.74)
VDD: 3.0Vto 3.6V
Standard Microcircuit Drawing 5962-01517
PRODUCT DESCRIPTION
The UT28F256LVQL amorphous silicon ViaLinkTM PROM is
a high performance, asynchronous, radiation-hardened, 32K x 8
programmable memory device. The UT28F256LVQL PROM
features fully asychronous operation requiring no external clocks
or timing strobes. An advanced radiation-hardened twin-well
CMOS process technology is used to implement the
UT28F256LVQL. The combination of radiation-hardness, fast
access time, and low power consumption make the
UT28F256LQL ideal for high speed systems designed for
operation in radiation environments.
DECODER MEMORY
ARRAY
SENSE AMPLIFIER
PROGRAMMING
CONTROL
LOGIC DQ(7:0)
A(14:0)
CE
PE
OE
Figure 1. PROM Block Diagram
3
DEVICE OPERATION
The UT28F256L VQL has three control inputs: Chip Enable (CE),
Program Enable (PE), and Output Enable (OE); fifteen address
inputs, A(14:0); and eight bidirectional data lines, DQ(7:0). CE
is the device enable input that controls chip selection, active, and
standby modes. Asserting CE causes IDD to rise to its active value
and decodes the fifteen address inputs to select one of 32,768
words in the memory. PE controls progra m and read operations.
During a read cycle, OE must be asserted to enable the outputs.
PIN NAMES
Table 1. Device Operation Truth Table 1
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
ABSOLUTE MAXIMUM RATINGS 1
(Referenced to VSS)
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the
device at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2. Test per MIL-STD-883, Method 1012, infinite heat sink.
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
V
SS
V
DD
PE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
PIN CONFIGURATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
A(14:0) Address
CE Chip Enable
OE Output Enable
PE Program Enable
DQ(7:0) Data Input/Data Output
OE PE CE I/O MODE MODE
X 1 1 Three-state Standby
0 1 0 Data Out Read
1 0 0 Data In Program
1 1 0 Three-state Read 2
SYMBOL PARAMETER LIMITS UNITS
VDD DC supply voltage -0.3 to 6.0 V
VI/O Voltage on any pin -0.5 to (VDD + 0.5) V
TSTG Storage te mperature -65 to +150 °C
PDMaximum power dissipation 1.5 W
TJMaximum junction temperature +175 °C
ΘJC Thermal resistance, junction-to-case 23.3 °C/W
IIDC input current
±
10 mA
4
RECOMMENDED OPERATING CONDITIONS
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(VDD = 3.0V to 3.6V; -55 °C < TC < +125°C)
Notes:
* Post-radiation pe rfo rm ance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rad(Si).
1. Measured only for initial qualification, and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
4. 1.7mA/MHz.
SYMBOL PARAMETER LIMITS UNITS
VDD Positive supply voltage 3.0 to 3.6 V
TCCase temperature range -55 to +125 °C
VIN DC input voltage 0 to VDD V
SYMBOL PARAMETER CONDITION MINIMUM MAXIMUM UNIT
VIH High-level input voltage 0.7VDD V
VIL Low-level input voltage 0.25VDD V
VOL1 Low-level output voltage IOL = 100µA, VDD = 3.0V VSS + 0.05 V
VOL2 Low-level output voltage IOL = 1.0mA, VDD = 3.0V VSS + 0.10 V
VOH1 High-level output voltage IOH = -100µA, VDD = 3.0V VDD-0.15 V
VOH2 High-level output voltage IOH = -1.0mA, VDD = 3.0V VDD-0.3 V
CIN 1Input capacitance, all inputs
except PE
Input Capacitance PE
ƒ = 1MHz, VDD = 3.3V
VIN = 0V
15
20
pF
CIO 1 Bidirectional I/O capacitance ƒ = 1MHz, VDD = 3.3V
VOUT = 0V
15 pF
IIN Input leakage current VIN = 0V to VDD, all pins except PE
VIN = VDD, PE only
-3 3
35 µA
µA
IOZ Three-state output leakage
current VO = 0V to VDD
VDD = 3.6V
OE = 3.6V
-20 20 µA
IOS 2,3 Short-circuit output current VDD = 3.6V, VO = VDD
VDD = 3.6V, VO = 0V -100 100 mA
mA
IDD1(OP)4Supply current operating
@15.4MHz (65ns product) CMOS input levels (IOUT = 0), VIL =
0.2V
VDD, PE = 3.6V, VIH = 3.0V 50.0 mA
IDD2(SB)
post-rad Supply current standby CMOS input levels VIL = VSS +0.25V
CE = VDD - 0.25 VIH = VDD - 0.25V 1.0 mA
5
READ CYCLE
A combination of PE greater than VIH(min), and CE less than
VIL(max) defines a read cycle. Read access time is measured from
the latter of device enable, output enable, or valid address to valid
data output.
An address access read is initiated by a change in address inputs
while the chip is enabled with OE asserted and PE deasserted.
Valid data appears on data output, DQ(7:0), after the specified
tAVQV is satisfied. Outputs remain active throughout the entire
cycle. As long as device enable and output enable are active, the
address inputs may change at a rate equal to the minimum read
cycle time.
The chip enable-controlled access is initiated by CE going active
while OE remains asserted, PE remains deasserted, and the
addresses remain stable for the entire cycle. After the specified
tELQV is satisfied, the eight-bit word addressed by A(14:0)
appears at the data outputs DQ(7:0).
Output enable-controlled access is initiated by OE going active
while CE is asserted, PE is deasserted, and the addresses are
stable. Read access time is tGLQV unless tAVQV or tELQV have not
been satisfied.
AC CHARACTERISTICS READ CYCLE (Post-Radiation)*
(VDD = 3.0V to 3.6V; -55 °C < TC < +125°C)
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rads(Si).
1. Functional test.
2. Three-state is defined as a 200mV change from steady-state output voltage.
SYMBOL PARAMETER 28F256LV-65
MIN MAX UNIT
tAVAV1Read cycle time 65 ns
tAVQV Read access time 65 ns
tAXQX2Output hold time 0 ns
tGLQX2OE-controlled output enable time 0 ns
tGLQV OE-controlled access time 35 ns
tGHQZ OE-controlled output three-state time 35 ns
tELQX2 CE-controlled output enable time 0 ns
tELQV CE-controlled access time 65 ns
tEHQZ CE-controlled output three-state time 35 ns
6
RADIATION HARDNESS
The UT28F256LVQL PROM incorporates special desig n and
layout features which allow operation in high-level radiation
environments. Aeroflex Colorado Springs has developed
special low-temperature processing techniques designed to
enhance the total-dose radiation hardness of both the gate oxide
and the field oxide while maintain ing the circuit density and
reliability. For transient radiat ion hardness and latchup
immunity, Aeroflex Colorado Springs builds all radiation-
hardened products on epitaxial wafers using an advanced twin-
tub CMOS process. In addition, Aeroflex Colorado Springs pays
special attention to power and ground distributio n during the
design phase, minimizing dose-rate upset caused by rail
collapse.
RADIATION HARDNESS DESIGN SPECIFICATIONS 1
Note:
1. The PROM will not latchup during radiation exposure under recommended operating conditions.
Figure 2. PROM Read Cycle
tAVAV
tAVQV
tELQV
tGLQV
tAVQV
tAXQX
tEHQZ
tGHQZ
A(14:0)
CE
OE
DQ(7:0) tGLQX
tELQX
Total Dose 1E6 rad(Si)
Latchup LET Threshold >110 MeV-cm2/mg
Memory Cell LET Threshold >100 MeV-cm2/mg
Logic SEU Onset LET >40 MeV-cm2/mg
SEU Cross Section 7.6E-12 cm2/bit
Error rate - geosynchronous orbit, Adams 90% worst case environment 2.5E-17 errors/bit day
7
Notes:
1. 50pF including scope probe and test socket.
2. Measurement of data output occurs at the low to high or high to low transition mid-point .
90%
Figure 3. AC Test Loads and Input Waveforms
Input
Pulses
10%
< 5ns < 5ns
0V
VDD
200 ohms
V
REF
=1.40V
50pF 90%
10%
8
0.015
0.008
0.015
0.008 PIN NO. 1 ID. 6
26 PLACES
0.050 BSC
e
E1
0.550 MAX
-B-
7
S1
(4) PLACES
0.000 MIN.
7
-D-
-C-
A
0.115
0.045
0.045
0.026 L
0.370
0.250
E2
0.180 MIN E3
0.030 MIN
E
0.520
0.460
-H-
c
0.009
0.004
0.040
0.022
0.015 28 PLACES
-A-
HA-B D5
SS
0.010 M
HA-B D
5
SSM
0.036
TOP VIEW
END VIEW
b
k
k
Q
Figure 5. 28-Lead 50-mil Center Flatpack (0.490 x 0.74)
Notes:
1. All exposed metalized areas to be plated per MIL-PRF-38535.
2. The lid is connected to V
SS
.
3. Lead finishes are in accordance with MIL-PRF-38535.
4. Dimension letters refer to MIL-STD-1835.
5. Lead position and coplanari ty are not measured.
6. ID mark symbol is vendor option.
7. With solder, increase maximum by 0.003.
8. Total weight is approximately 2.4 grams.
D
0.740 MAX
9
ORDERING INFORMATION
UT28F256LVQL PROM: SMD
Lead Finish:
(A) = Solder
(C) = Gold
(X) = Optional
Case Outline:
(X) = 28-lead Flatpack
Class Designator:
(Q) = Class Q
(V) = Class V
Device Type
(02) = 65ns Access Ti me, CMOS compatible inputs and CMOS compatible outputs
(03) = 65ns Access Ti me, CMOS compatible inputs and CMOS compatible outputs
Extended Industrial Temp (-40
c
C to +125
o
C)
Drawing Number: 01517
Total Dose:
(F) = 3E5 rads(Si)
(G) = 5E5 rads(Si)
(H) = 1E6 rads(Si)
(R) = 1E5 rads(Si)
Federal Stock Class Designator: No options
5962 * 01517 * * * *
Notes:
1. Lead finish (A, C, or X) must be specified.
2. If an “X” is specified when ordering, part marking will match the lead finish and will be either “A” (solder) or “C” (gold).
3. Total dose radiation must be specified when ordering. QML Q and QML V not available without radiation hardening.
4. Device type 03 available with total dose of 1E5 rads(Si) or 3E5 rads(Si).
10
UT28F256LV PROM
UT **** *** - * * * * * *
Total Dose:
( ) = None
Lead Finish:
(A) = Solder
(C) = Gold
(X) = Optional
Screening:
(C) = Mil Temp
(P) = Prototype
(W) = Extended Indu strial Tem p (-4 0
c
C to +125
o
C)
Package Type:
(U) = 28-lead Flatpack
Access Time:
(65) = 65ns access time
Device Type Modifier:
(C) = CMOS compatible inputs and CMOS compatible outputs
Device Type:
(28F256LVQL) = 3.3V, 32Kx8 One Time Programmable PROM
Notes:
1. Lead finish (A,C, or X) must be specified.
2. If an “X” is specified when ordering, then the part marking will match the lead finish and will be either “A” (solder) or “C” (gold).
3. Military Temperature Range flow per Aeroflex Colorado Springs Manufacturing Flows Document. Radiation characteristics are neither tested nor
guaranteed and may not be specified.
4. Prototype flow per Aeroflex Colorado Springs Manufacturing Flows Document. Devices have prototype assembly and are tested at 25°C only . Radiation
characteristics are neither tested nor guaranteed and may not be specified.
5. Lead finish is gold only.
11
COLORADO
Toll Free: 800-645-8862
Fax: 719-594-8468
SE AND MID-ATLANTIC
Tel: 321-951-4164
Fax: 321-951-4254
INTERNATIONAL
Tel: 805-778-9229
Fax: 805-778-1980
WEST COAST
Tel: 949-362-2260
Fax: 949-362-2266
NORTHEAST
Tel: 603-888-3975
Fax: 603-888-4585
CENTRAL
Tel: 719-594-8017
Fax: 719-594-8468
www.aeroflex.com info-ams@aeroflex.com
Our passion for perform a nce is defined by three
attributes represented by the s e three icons:
solution-minde d, perform an c e-d riven and custom e r-focu sed
Aeroflex Colorado Springs, Inc. reserves the right to make
changes to any products and services herein at any time
without notice. Consult Aeroflex or an authorized sales
representative to verify that the information in this data sheet
is current before using this product. Aeroflex does not assume
any responsibility or liability arising out of the application or
use of any product or service described herein, except as
expressly agreed to in writing by Aeroflex; nor does the
purchase, lease, or use of a product or service from Aeroflex
convey a license under any patent rights, copyrights,
trademark rights, or any other of the intellectual rights of
Aeroflex or of third parties.