-1- IRAUDPS1 12V System Scalable 250W to1000W Audio Power Supply For Class D Audio Power Amplifiers Using the IR2085 self oscillating gate driver And Direct FETS IRF6648 By Manuel Rodriguez CAUTION: International Rectifier suggests the following guidelines for safe operation and handling of IRAUDPS1 Demo Board: * Always wear safety glasses whenever operating Demo Board * Avoid personal contact with exposed metal surfaces when operating Demo Board * Turn off Demo Board when placing or removing measurement probes www.irf.com IRAUDPS1 Page 1 of 35 -2- Page Table of Contents Item 1 Introduction 3 2 System Specifications 4 3 Functional Block Description 5 4 IRAUDPS1 Block Diagram 6 5 Schematic IR2085 module 7 6 IRAUDPS1 mother board schematic 8 7 IR2085 module PCB layout 9 8 IRAUDPS1 mother PCB layout 10-11 9 BOM of IR2085 module 12 10 BOM of IRAUDPS1 mother board 13-14 11 BOM of Mechanical parts 14 12 Scalable IRAUDPS1 power table 14 13 Performance and test procedure 15-21 14 IRAUDPS1 Fabrication Drawings 22-24 15 Transformer winding instructions 25-27 16 Design example 28 17 Transformer design 28-30 18 MOSFET selection 30 19 Switching losses 31 20 Efficiency calculations 32 21 Frequency of oscillation 33 22 Selecting dead time 33 23 Over Temperature Protection 33 24 Short circuit protection 33 25 BJT gate driver option 33 26 Music Load 34 25 Revision Changes Descriptions 35 www.irf.com IRAUDPS1 Page 2 of 35 -3- Introduction The IRAUDPS1 reference design is a 12 volts systems Audio Power Supply for automotive applications designed to provide voltage rails (+B and -B) for Class D audio power amplifiers This reference design demonstrates how to use the IR2085 as PWM and gate driver for a Push-Pull DC to DC converter, along with IR's Direct FETS IRF6648 The resulting design uses a compact design with the Direct FETS and provides all the required protections. NOTE: The IRAUDPS1 is an scalable power output design, and unless otherwise noted, this user's manual and the reference design board is the 500W Table 1 IRAUDPS1 scalable table Nominal Voltage output Nominal Output Current IRAUDPS1 250W 500W 1000W +B, -B 35V 35V 35V +B, -B 3.5A 7A 14A Stereo System 8 channel System 8 channel System 100W x 2 100W x 4 100W x 8 IR Class D Model IRAUDAMP7D IRAUDAMP8 IRAUDAMP8 x 2 Detailed output power versions that can be configured by replacing components given in the component selection of Table 7 on page 14 Application . www.irf.com IRAUDPS1 Page 3 of 35 -4- System Specification All specs and tests are based on a 14.4V battery voltage supplying an International Rectifier Class D reference design with all channels driven at 1 kHz and a resistive load. Table 2 Specification IR Class D Load Input current with no load ACC Remote ON Level ACC input impedance Turn ON delay In-Rush Current Output power full loaded Input current full loaded Output Current per supply Output voltage Regulation Ripple outputs, laded at 400W audio 1khz 250W IRAUDAMP5 0.35A +/- 10% 4.5-6V 10k+/- 10% 1-1.5 Sec 30A Max 250W 18A 3.5A +/- 35V +/-10% +/- 10% 1.5V P.P. IRAUDPS1 IRAUAMP8 0.35A +/- 10% 4.5-6V 10k+/- 10% 1-1.5 Sec 30A Max 500W 35.5A 7A +/- 35V +/-10% +/- 10% 1.8V P.P. 1000W IRAUAMP8 x 2 0.35A +/- 10% 4.5-6V 10k+/- 10% 1-1.5 Sec 30A Max 1000W 71A 14A +/- 35V +/-10% +/- 15% 2V P.P. Efficiency at 1/2 and full of rated power Isolation between Battery and Outputs Gnd Battery OVP Battery UVP Output SCP Outputs OVP Over temperature protection (OTP) OTP hysteresis Led Indicators Size 90-85% 92-87% 90-80% 1k Ohm 1k Ohm 1k Ohm 18-18.5V 8.0-8.5V 10A 40-45V 90C +/- 5C 18-18.5V 8.0-8.5V 20A 40-45V 90C +/- 5C 18-18.5V 8.0-8.5V 40A 40-45V 90C +/- 5C 10C 10C Red LED= SCP, Blue LED= OK 3" W x 5.3" L x 1.5" H Table 3 +B, -B Voltage outputs vs. Battery voltage all models Voltage outputs at 16.0V battery input with no signal input at class D Voltage outputs at 12.0V Voltage outputs at 8.0V battery input with no signal input at class D www.irf.com IRAUDPS1 10C +/- 39.5V +/- 10% +/- 28V +/- 10% +/- 19.2V +/- 10% Page 4 of 35 -5- Functional Block Description Fig 1 below shows the functional block diagram which basically is an isolated DC-DC converter with a step-up push-pull transformer from a 12V system that converts it to +/- 35V using the IR2085 as a PWM and gate driver along with the Direct FETS IRF6648. The IR2085 Module contains all the housekeeping circuitry to protect the IRAUDPS1 against streamer conditions which are: 1. Soft start circuit in order to control the inrush-current at the moment the IRAUDPS1 power is turned ON 2. Short Circuit protection at outputs (SCP), which will shut down the IR2085 and remain in latch mode until the Remote ON /OFF switch is released 3. 12V system Over Voltage protection (OVP1). if Battery input voltage is greater than 18V.. this could happen when the vehicle's battery is disconnected or a vehicle's alternator fails. 4. Over voltage Output (OVP2) is greater than +/-45V at +B terminal if battery input is greater than 16V 5. Over Temperature Protection (OTP), resistor Thermistor senses the chassis temperatures from Direct FETS Fig 2 is the complete schematic for the IR2085 Module Fig 3 is the complete schematic for the IRAUDPS1 with all scalable components required Figs 4 to Fig 10 are the respective PCB layouts for the IR2085 Module and the IRAUDPS1 motherboard Tables 4 to Table 6 are the respective bills of materials Table 7 is the IRAUDPS1 detailed output power versions that can be configured by replacing components www.irf.com IRAUDPS1 Page 5 of 35 -6- IRAUDPS1 Block Diagram PUSH PULL +B Supply Rectifiers & filters FUSES Battery terminal inputs +BATT. +B SGnd -B +14.4V EMI Filter GND -B Supply Rectifiers & filters Chassis GND OVP1 IR2085 +Batt, OVP Batt Gnd SGnd SD Soft Start SCP ON Remote ON/OFF Rem Rem ON/OFF and +12V Regulator +B, OVP OTP Thermistor Thermally connected to heat spreader OVP2 IR2085 Module Fig 1 Functional Block Diagram . www.irf.com +Current Sense IRAUDPS1 Page 6 of 35 -Current Sense -7- 1 10k R16 2 47k R23 10k 1 1 10k 2 2 2 1 LO1 1 30K R1 OSC U2 HO1 7 1 VS2 3 GND VS1 6 4 LO VCC 5 14.4V 470pF R1 @ C2_470pF: 15k=100khz 30k=50khz VCC 1nF,15k=50kHz VCC 2 2 2 R25 Turn_ON R11 2 2.2 Q1 14.4V 3 14 1 2 22 2 1 open 10uF 2 1 12V 1 1 10k 2 0.1uF 2 2 Remote ON 22 R21 Remote ON J1 1 6 5 4 3 2 1 Header 6H 2 R8 4.7k TH1 2085_Control Module_R3 Fig 2 schematic of IR2085 Module IRAUDPS1 2 1 Header 2 R9 6 J5 1 R20 C8 R26 1 J4 DZ3 1k 2 5 0.0 VS1 R30 VCC CP2 1 1 2 1 4.7k www.irf.com 2 1 4 3 2 1 14.4V Q6 Q2 BlueLED2 J3 22 Header 2 Q4 open C2 2 1 2 1 open 2 1 2 R19 8 VB1 1 Header 2 R27 VCC CS 2 0.0 J2 22 R18 0.1uF 1 1 2 D4 CS 2 C6 2 IR2085 3 2 1 Q3 open R14 1 14.4V 1k C2: 47pF=80nS 100pF=110nS 220pF=130nS 470pF=170nS 1nF1= 200ns 2 J6 R24 1 4.7k 1 C3 R13 1 4 OVP2 D7 1 2 1 1 2 2 V1 1 2 1 10k R15 470k R10 1 D3 Soft Start SCP SCP- 10k 1 Q5 2 3 2 2 V1 LM393 10k 2 R3 10k 1 0.01uF 2 1 C1 R2 R33 1 2 OVP 2 18V DZ1 1 D2 V1 2 12 1 1 R28 1 SCP+ DZ2 10uF 2 1 C7 U1A 2 R4 1 2 10k 2 0.1uF R17 1k 1 D5 2 1Meg Turn_ON OVP2 2 5.6V 1 0.01uF 2 14.4V 2 R6 1 2 470 TH1 10k 5 1 D1 6 SCP 6 LM393 C5 1 2 SCP- 2 7 1 1 5 OTP U1B R31 1 2 D6 C4 2 2 V1 SCP+ 2 4 1 LED1 3 DZ4 8 R22 Q7 Turn_ON 1 CP1 100pF 2 10k 2 1 R32 0.01uF 1 1 V1 2 R29 10V Red 4.7k Page 7 of 35 -8. IRAUDPS1, 12V System SMPS, 500W Converter with Direct Fets And IR2085 PWM Module Optional (open) MUR1620CTG 1 SW2 2 CR1 +V_Rectified 3 SW1 +B VS2 3 5 Header 2 2 2.2K D_FET6 IRF6648 1 1 2.2K 2 R14 C3 15A 2 +CS Q1 2 VS1 1 SMAZ39-TP Header 4 2.2nF/100V 2 1 2 VS1 R72 6.2 1uF 1uF 1 1 R43 100R L5 3 2 D4 1 2 0.1uF/250V 3 S2 S2 C22 4 5 ZP42915TC 2 D2 C21 1 1 D3 0.01uF 1 C26 1 C23 2 1 L2 1 2 LED2 LO2B 6 5 4 3 2 1 2 GND C30 Chassis GND 1 2 1 0.01uF C32 2 1 0.01uF SGnd Fig 3 IRAUPS1 Mother Board Schematic . www.irf.com 1 SGnd -B TH1, thermally connected to heat-spreader IRAUDPS1 Page 8 of 35 1 R55 2.2k R61 22k R56 2.2k CP13 CP11 2700uF/35V 2 C24 +V 2 1 SGnd 3 -V 2 R54 1 2 0.03R R48 2 1 -B 2 -B 2 R52 SCP- 2 1 10k 0.01uF 1 LED1 R45 1k J1 +B 1uF/100V 22k 0.1uF 1 2 2 1 R16 R60 2700uF/35V 7 2 4 6 2.2K 2 1 12 TB4 2 1uF/100V Q2 MMBT5551 2 1 1 2 0.03R 1 1 SW2 C25 1 1uF/100V +B D_FET16 IRF6648 3 5 3 5 3 5 1 7 2 4 6 7 2 4 6 7 2 4 6 3 5 2.2K D_FET12 1 open R32 TH1 2 2 Header 2 D_FET8 IRF6648 1 100K TH-805 1 Manual ON/OFF 14.4V 3PSW 3 2 1 off S1 Remote ON/OFF 2 1 2 TB3 D_FET4 1 open 1 2 R49 2 C35 LO2A J5 R47 0.03R -V_Rectified TB1 2 1 0.1uF/250V 3 2 C29 +V 10k R50 CP12 1uF 6 2 C28 C31 1uF/100V 2 1 C9 +B 1 1 2 1 C8 R71 C33 1uF 6.2 2 3 C7 L1 3.3uH/10A 2 D1 MMBT5401 CP10 2700uF/35V Z1 14.4V 7 +V_Rectified 2700uF/35V VS2 2 3 L6 2 SMAZ39-TP 4 3 2 1 2 F3 1 R44 1000pF/200V 2 1 2 J4 14.4V R73 Z2 Fuse3 1 10k 1 1 SW1 1 S1 1 2.2nF/100V 2 1 TB2 FB2 1 R70 CP5 2 F2 15A 6.2 CP4 3300uF/25V Fuse2 1 SCP+ 1 2 CP3 3300uF/25V 15A 14.4V 8 P1 10 2 C34 6.2 3300uF/25V FB1 2085 Module 2 F1 TR1 R51 2 2.2nF/100V 2 1 Header 2 Fuse1 1 SW1 LO1B 2 1 1 1 (open) MUR1620CTRG 3 2 CR2 -V_Rectified 1 SW2 Transformer: Core: Magnetics P/N ZR42915TC P1,P2=4T#18x4,60uH,DCR 3mOhms S1,S2=10T#20x3=470uH,DCR 46mOhms D_FET14 IRF6648 R31 J2 +Battery 7 2 4 6 D_FET10 1 open 3 5 D_FET2 1 open 1 7 2 4 6 LO1A 2 1 3 5 Header 3 J3 7 2 4 6 SCP+ SCP- 3 5 3 2 1 7 2 4 6 J6 2 0.03R C27 R53 2 1 10k -CS -V -9- Fig 4 IR2085 Module Top silk screen layout . Fig 5 IR2085 Module bottom side layout Fig 6 IR2085 Module Top side layout . www.irf.com IRAUDPS1 Page 9 of 35 - 10 . Fig 7 IRAUDPS1 Mother Board Top silk screen layout . Fig 8 IRAUDPS1 Mother Board Top copper www.irf.com IRAUDPS1 Page 10 of 35 - 11 - . Fig 9 IRAUDPS1 Mother Board Bottom silk screen layout . . Fig 10 IRAUDPS1 Mother Board Bottom layout www.irf.com IRAUDPS1 Page 11 of 35 - 12 - Bill of Materials Table 4 IRS2085 Module Quantity Value Description Designator Digikey P/N Vendor 3 0.01uF CAP 10000PF 50V CERM X7R 0603 C1, C4, C5 PCC1784CT-ND Panasonic - ECG 1 470pF CAP CER 470PF 50V 5% C0G 0603 C2 490-1443-1-ND Murata 1 100pF CAP CERAMIC 100PF 50V NP0 0603 C3 311-1069-1-ND Yageo 3 0.1uF CAP CERM .10UF 50V 20% 0805 SMD C6, C7, C8 478-3351-1-ND AVX Corporation 2 10uF CAP TANTALUM 10UF 16V 10% SMD CP1, CP2 495-2236-1-ND Kemet 7 1N4148WT-7 DIODE SWITCH 100V 150MW SOD-523 D1, D2, D3, D4, D5, D6, D7 1N4148WTDICT-ND Diodes Inc 1 18V SOD123_Z DZ1 MMSZ5248BS-FDICT-ND Diodes Inc 1 5.6V DIODE ZENER 5.6V 200MW SOD-323 DZ2 UDZSTE-175.6BCT-ND Rohm 1 12V DIODE ZENER 200MW 12V SOD323 DZ3 BZT52C12S-TPMSCT-ND Micro Commercia 1 10V DIODE ZENER 10V 200MW SOD-323 DZ4 MMSZ5240BSDICT-ND Diodes Inc 1 Header Header, 6-Pin, Right Angle J1,J2,J3,J4,J5.J6 929500E-01-01-ND 3M 1 Red LED RED ORAN CLEAR THIN 0805 SMD LED1 160-1422-1-ND Lite-On Inc 1 Blue LED 468NM BLUE CLEAR 0805 SMD LED2 160-1645-1-ND Lite-On Inc 2 XN04311 TRANS ARRAY PNP/NPN W/RES MINI6P Q1, Q7 XN0431100LCT-ND Panasonic - SSG 1 PBSS305NX TRANS NPN 80V 4.6A SOT-89 Q2 568-4177-1-ND NXP 2 open (OPEN) TRANS NPN 80V 4.6A SOT-89 Q3, Q4 568-4177-1-ND NXP 2 open (OPEN) TRANS PNP 80V 4A SOT-89 Q5, Q6 568-4178-1-ND NXP 1 30K RES 30K OHM 1/10W 5% 0603 SMD R1 RHM30KGCT-ND Rohm 1 1k RES 1K OHM 1/10W 5% 0603 SMD RHM1.0KGCT-ND Rohm 11 10k RES 10K OHM 1/10W 5% 0603 SMD R2 R3,R6,R9,R14, R15, R16, R17, R23, R24, R32,R33 RHM10KGCT-ND Rohm 1 1Meg RES 1.0M OHM 1/10W 5% 0603 SMD R4 311-1.0MGRCT-ND Yageo 4 4.7k RES 4.7K OHM 1/10W 5% 0603 SMD R8, R13, R22, R25 RHM4.7KGCT-ND Rohm 1 470k RES 470K OHM 1/10W 5% 0603 SMD R10 RHM470KGCT-ND Rohm 1 2.2 RES 2.2 OHM 1/4W 1% 1206 SMD R11 P2.2RCT-ND Panasonic - ECG 4 22 RES 22 OHM 1/8W 5% 0805 SMD R18, R19, R20, R21 RHM22ARCT-ND Rohm 2 1k RES 1.0K OHM 1/10W 5% 0603 SMD R26, R28 RHM1.0KGCT-ND Rohm 2 0.0 RES 0.0 OHM 1/8W 5% 0805 SMD R27, R30 RHM0.0ARCT-ND Rohm 1 47k RES 47K OHM 1/10W 5% 0603 SMD R29 RHM47KGCT-ND Rohm 1 470 RES 470 OHM 1/8W 5% 0805 SMD R31 RHM470ARCT-ND Rohm 1 LM393DR2G IC COMP DUAL OFFSET LV 8SOIC U1 LM393DR2GOSCT-ND ON Semi 1 IR2085 Controller and Gate Driver U2 IR2085 International Rect www.irf.com IRAUDPS1 Page 12 of 35 - 13 - Table 5 IRAUDPS1 Mother Board Bill of Materials Quantity Value Description Designator Digikey P/N Vendor 4 1uF/50V CAP CER 1UF 50V X7R 1206 C3, C7, C8, C9 490-3908-1-ND Murata Electronics North 1 1000pF/200V CAP CER 1000PF 10% 200V X7R 1206 C21 478-1505-1-ND AVX Corporation 3 2.2nF/100V CAP CER 2200PF 10% 100V X7R 1206 C22, C33, C34 478-1519-1-ND AVX Corporation 4 1uF/100V CAP CER 1UF 100V X7R 1206 C23, C24, C31, C35 490-3909-1-ND Murata Electronics 4 0.01uF CAP 10000PF 50V CERM X7R 0603 C26, C27, C30, C32 PCC1784CT-ND Panasonic - ECG 3 0.1uF/250V CAP CERAMIC .1UF 250V X7R 1206 C28, C29,C25 399-4674-1-ND Kemet 3 3300uF/25V CAP 3300UF 25V ELECT PW RADIAL CP3, CP4, CP5 493-1842-ND Nichicon 4 1200uF/63V CAP 1200UF 63V ELECT PW RADIAL CP10, CP11, CP12, CP13 493-1958-ND Nichicon 1 (open) DIODE Comm Cathode ULT FAST 16A 200V TO220 CR1 MUR1620CTGOS-ND ON Semiconductor 1 (open) DIODE Comm Anode ULT FAST 16A 200V TO220 CR2 MUR1620CTRGOS-ND ON Semiconductor 4 STTH1002CB DIODE FAST 200V 10A D-PAK D1, D2, D3, D4 497-3536-5-ND STMicroelectronics 4 open Direct-FET MOSFET N-CH 60V 86A FET2, FET4,FET10,FET12 IRF6648TR1PBFCT-ND International Rectifier 4 IRF6648 Direct-FET MOSFET N-CH 60V 86A FET6, FET8, FET14,FET16 IRF6648TR1PBFCT-ND International Rectifier 3 Fuse Holder FUSEHOLDR MINI VERT PCB MNT SNGL F1, F2, F3 F065-ND Littelfuse Inc 2 FERRITE QUAD LINE 10A FERRITE 3 LINE 10A 342 OHMS FB1, FB2 240-2494-ND Stwart 3 15A FUSE BLADE 15A/32V MINI FAST-ACT Fuse1, Fuse2, Fuse3 F992-ND Littelfuse Inc 1 Module_2085_R2 Control Module J1,J2, J3, J4,J5,J6 Custom IR Module_2085_R2 PCB 2 3.3uH/10A INDUCTOR POWER 3.31UH 11.4A T/H L1, L2 513-1522-ND Coiltronics 1 Blue LED 468NM BLUE CLEAR 0805 SMD LED1 160-1645-1-ND Lite-On Inc 1 Blue LED 468NM BLUE CLEAR 0805 SMD LED2 160-1645-1-ND Lite-On Inc 1 MMBT5401 TRANSISTOR PNP 150V SOT-23 Q1 MMBT5401FSCT-ND Fairchild Semiconductor 1 MMBT5551 TRANSISTOR NPN 160V SOT-23 Q2 MMBT5551FSCT-ND Fairchild Semiconductor 4 2.2K RES 2.2K OHM 1/8W 5% 0805 SMD R14, R16, R31, R32 'RHM2.2KARCT-ND Rohm 1 100R RES 100 OHM 1/4W 5% 1206 SMD R43 311-100ERCT-ND Yageo 1 10 RES 10 OHM 1/4W 5% 1206 SMD R44 RHM10ERCT-ND Rohm 1 1k RES 1.0K OHM 1/4W 5% 1206 SMD R45 RHM1.0KERCT-ND Rohm 4 0.03R RES .03 OHM 1W 1% 2512 SMD R47, R48, R49, R54 WSLG-.03CT-ND Vishay/Dale 4 10k RES 10K OHM 1/10W 5% 0603 SMD R50, R51, R52, R53 RHM10KGCT-ND Rohm 2 2.2k RES 2.2K OHM 1W 5% 2512 SMD R55, R56 PT2.2KXCT-ND Panasonic - ECG 2 22k RES 22K OHM 1/4W 5% 1206 SMD R60, R61 RHM22KERCT-ND Rohm www.irf.com IRAUDPS1 Page 13 of 35 - 14 - 1 Toggle SW 3Pos Toggle SW 3Pos S1 EG2377-ND E-Switch 2 Gold terminal block Gold terminal Block #8 AWG TB1, TB2 070-850 Audio Express 1 TB 2 terminals CONN TERM BLOCK 2POS 5MM PCB TB3 277-1022-ND Phoenix Contact 1 1714984 CONN TERM BLOCK 3POS 9.52MM PCB TB4 277-1272-ND Phoenix Contact 1 100K THERMISTOR 100K OHM NTC 0805 SMD TH1 490-2451-1-ND Murata Electronics 1 ZP42915TC Power Transformer TR1 Custom TR500-2085 Magnetics 2 SMAZ39-TP DIODE ZENER 1W 39V SMA Z1, Z2 SMAZ39-TPMSCT-ND Micro Commercial Co . Table 6 Mechanical BOM Quantity Description Value Digikey P/N Vendor 1 Aluminum Bar heat spreader R2 Aluminum Bar 2085 Custom China 1 Aluminum Base heat sink R2 Aluminum Bar 2085 Custom 2085 China 1 Print Circuit Board IR2085_MB_R2 .PCB PCB IR2085_MB_R1 PCB Assy China 1 THERMAL PAD .080" 4X4" GAPPAD THERMAL PAD .080" 4X4" GAPPAD Ber164-ND Bergquist 2 (Optional) THERMAL PAD .007" W/ADH (Optional) THERMAL PAD TO-220 173-7-240A Wakefield 4 SPACER ROUND 1" #4 SCRW .250" BR Stand off 0.250" 1454AK-ND Keystone Electronics 6 NUT HEX 4-40 STAINLESS STEEL Nut 4-40 H724-ND Building Fasteners 6 SCREW MACHINE PHILLIPS 4-40X3/4 Screw 4-40X3/4 H350-ND Building Fasteners 12 WASHER LOCK INTERNAL #4 SS Washer #4 SS H729-ND Building Fasteners . Table 7 Scalable IRAUDPS1 by changing the following components Component Notes 250W IRAUDPS1 1000W Power Transformer T1 See winding instructions IR P/N TR-2085-250W IR P/N TR-2085-500W IR P/N TR-2085-1000W Direct FETs Populate the respective Direct FET by IR6648 as shown on respective model D_FET6, D_FET16 D_FET6,D_FET8, D_FET16 R47, R48, R47, R54 Short circuit sensitivity 0.06R 0.03R 0.015R Fuse F1, F2, F3 Input Current 5A 15A 25A D_FET14, D_FET6,D_FET8, D_FET16 D_FET14, D_FET2,D_FET4, D_FET12 D_FET10, D1, D2, D3, D4 Output Rectifiers 4A 8A 16A CP3, CP4, CP5 Input Filters 2200uF/25V 3300uF/25V 3900uF/25V . www.irf.com IRAUDPS1 Page 14 of 35 - 15 - IRAUPS1 Application and connections Fig 11 test Setup www.irf.com IRAUDPS1 Page 15 of 35 - 16 - Connector Description Battery ( - ) Battery ( + ) +B output Analog GND -B output TB1 TB2 TB4-1 TB4-2 TB4-3 Terminal Board for Negative supply source Terminal Board for Positive supply source Positive output of +B (+Bus Rail) Output GND of +B and -B Negative output of -B (-Bus Rail) Switch Description Remote-OFF-Test Remote OFF Test This position PS1 can be turned ON remotely by vehicle's ACC (Accessory voltage) or vehicle's amplifier IRAUDPS1 is always OFF regardless of ACC input IRAUDPS1 can be turned ON manually or for test purpose LED Indicator Description LED1 Red LED2 Blue LED3 Blue LED4 Blue Indicate the presence of a short circuit condition on +B or -B Indicate the presence of PWM pulses from IR2085 Indicate the presence of +B voltage Indicate the presence of -B voltage Power Source Requirements The power source shall be capable of delivering 80 Amps with current limited from 1A to 80A during the test; the output voltage shall be variable from 8V to 19V during the test Test Procedure 1. 2. 3. 4. 5. 6. 7. Pre-adjust the main source power supply to 14.4V and set current limit to 1A Turn on the main source power supply to standby mode On IRAUDPS1 (Unit Under Test) Set the Remote ON switch to OFF (center) Connect an oscilloscope probe on transformer terminals TR1 pin 1 Do NOT Connect the Class D Amp IRAUDAMP8 (IR2093) to +B and -B yet Connect the resistive load to the class D Amp Set the Audio OSC to 1 kHz and output level to 0.0V Power up: 8. Turn ON the main source power supply, the input current from the source power supply should be 0.0mA and all LEDS should be OFF 9. Look at LED2 on the IR2085_Module, it should be OFF, then turn ON the Remote-OFF-Test to Test switch while you observe LED2; it will light slightly after turning ON said switch, then LED2 will come fully bright one second after the Remote switch was turned ON (Test position) 10. In the mean time, the figure on the oscilloscope will start from narrow pulses, up to 50% duty cycle and the oscillation frequency shall be 50kHz as shown on Fig 12 and Fig 13 below; This is the soft-start test IRAUDPS1 Rev 3.3 www.irf.com Page 16 of 35 - 17 - Fig 12, waveform from 2085 module Fig 13, waveform from power transformer 11. The power consumption from the source power supply shall be 0.35A maximum typical is 0.30A and the +B and -B LEDs will turn ON as well 12. Measure the voltage on +B and -B; it will be +/-35V 1.5V respectively; This is the transformer's windings turns ratio and full-wave rectifiers UVP Test 13. Decrease the source power supply slowly until it reaches around 8 volts while you observe LED2 or the oscilloscope. LED2 will turn OFF or oscilloscope's pulse will disappear at 8V 1.5V. Typical is 8.02V OVP1 Test 14. Increase the source power supply slowly until it reaches around 18V while you observe LED2 or the oscilloscope. LED2 will turn OFF or the oscilloscope's pulse will disappear at 18V 1.5V. Typical is 18.5V OVP2 Test 15. Increase the source power supply slowly until it reaches around 16V while you observe LED2 or the oscilloscope;. LED2 will begin blinking or the oscilloscope's pulse will decrease in duty cycle like Fig12 when +B reaches 45V 2.5V. Typical is 45.0V SCP Test 16. Adjust the source power supply to 14.4V, then while IRAUPS1 is ON, apply a short circuit between +B and AGnd with external wires, (do not make the SC on the terminal board or it will burn said terminals) LED1 will turn ON and LED2 will be OFF and stay OFF until the Rem-OFF-Test Switch is turned to OFF then ON again; This is the latch of OCP 17. Repeat the last step for -B and GND IRAUDPS1 Rev 3.3 www.irf.com Page 17 of 35 - 18 - Full Load Power Test 18. Turn OFF the IRAUDPS1 and Connect +B and -B to the Class D Amp IRAUDAMP8 (IR2093) 19. Turn ON the IRAUDPS1, the input current from the source power supply should be 0.85A 0.5A; typical input current is 0.83A with the class D IRAUDAMP8 loaded with no signal input 20. Increase the current limit from the source power supply to 35A 21. Increase slowly the output level from the Audio Oscillator until the Class D amp gets 100W RMS per channel; if resistive loads are 4 Ohms the outputs amplitude from amplifier will be 20V RMS 22. Under these conditions the consumption current from the source power supply shall be 36.6A maximum; this correlates to a 10% loss for each channel and a 20% loss of the IRAUDPS1; this is the power output and efficiency test 23. The output voltages from +B and -B should be +/- 30V 2.5V 24. Monitor the transformer waveform; it should be like Fig 14 below 25. The ripple current for +B or -B should be 3V P.P. maximum as shown on Fig 15 below Fig 14 TR1 waveform loaded Fig 15 +B and -B Ripple voltage OTP Test 26. Leave the class D amp running with 100W x 4 continuous power until IRAUDPS1 gets hot and trips the shut down level while the temperature on the heat sink is monitored next to the Thermistor sensor. The temperature for shutdown will be 90C +/-5C and the time required to make OTP will be around 30 minutes when tested at ambient temperature 27. The thermal hysteresis shall be 10C and the time to recover it shall be one minute, the time to make shutdown again will be 10 minutes 28. Load Regulation and Efficiency are shown in Fig 16-20 below IRAUDPS1 Rev 3.3 www.irf.com Page 18 of 35 - 19 - Typical Performance Regulation Voltage output 40 35 30 25 20 15 10 5 0 1 2 3 4 5 6 7 8 IRAUDPS1-500W Load (Amps) Fig 16 . Effiency of IRAUDPS1-250W 100 90 80 Efficiency % 70 60 50 40 30 20 10 0 0 7 14 21 28 35 42 49 56 63 70 138 204 268 Watts Fig 17 . IRAUDPS1 Rev 3.3 www.irf.com Page 19 of 35 - 20 - Efficiency of IRAUPS1-500W 100 90 80 Efficiency % 70 60 50 40 30 20 10 0 0 7 14 21 28 35 42 49 56 63 69 137 204 267 333 393 457 512 Watts Fig 18 . Efficiency of IRAUDPS1-1000W 100 90 80 Effiency % 70 60 50 40 30 20 10 0 0 7 14 21 28 35 42 49 56 63 69 137 267 393 512 626 732 833 Watts Fig 19 . IRAUDPS1 Rev 3.3 www.irf.com Page 20 of 35 - 21 - +B, -B vs. Battery voltage outputs 50 +B and -B Voltage outputs 45 40 35 30 25 20 15 10 5 0 8 9 10 11 12 13 14 15 16 17 18 Battery voltage Fig 20 . . IRAUDPS1 Rev 3.3 www.irf.com Page 21 of 35 - 22 - IRAUDPS1 Fabrication Drawings Mechanical assembly . HEX NUT 4-40 P/N H216-ND HEX NUT 4-40 P/N H216-ND x 6 Lock washer Lock washer PCB Stand off 0.250" P/N 1454AK-ND x 4 Lock washer Stand off 0.250" P/N 1454AK-ND Thermal Pad Aluminum Bracket Lock washer Lock washer H729-ND x 12 Screw H350-ND x 6 Lock washer Lock washer Screw H350-ND Aluminum Base Lock washer Screw H350-ND Fig 22 Mechanical assembly . 0.032" 0.062" DirectFETS Gap 0.030" Lock washer PCB Lock washer Heat Spreader (Bar) Alumimum plate (Base) Lock washer Lock washer Fig 23 Direct FET thermal dissipation . IRAUDPS1 Rev 3.3 www.irf.com Page 22 of 35 - 23 - . Fig 24 Aluminum base Fig 25 Heat Spreader for DirectFETs . IRAUDPS1 Rev 3.3 www.irf.com Page 23 of 35 - 24 - Fig 26 Thermal Pad . . Fig 27 Input Battery Terminals IRAUDPS1 Rev 3.3 www.irf.com Page 24 of 35 - 25 - IRAUDPS1 transformer winding instructions IR Assy P/N IR-TR500-2085-500W Schematic Start Start P1 S1 Finish Finish Start Start P2 Materials required Core: Magnetics material "P" ZP42915TC S2 Finish Finish Fig 29 Fig 28 . Step No. 1 Winding P1: Fig No. 30 1. Cut 30cm length of 1.0mm gage x 4 wires of magnet wire (AWG 18) 2. Start winding P1 at 0 degrees forward or Clock wise, as shown on Fig 30, start is the top side, and finish is the bottom side 3. Wind 4 turns in parallel at the same time, evenly spaced around the core as shown on Fig 30 4. Leave 4 cm of wire at both ends, spaced 1/2 inch between ends, as shown on Fig 30 . Step No. 2 Winding P2: Fig No. 31 5. Cut 30cm of 1.0mm gage x 4 wires of magnet wire (AWG 18) 6. Start winding P2 starting on the end of P1, as shown in Fig 31, start is the top side, and finish is the bottom side 7. Wind the 4 at the same time between the spaces of P1 evenly spaced around the core, in the same direction as shown on Fig 31 8. Leave 4 cm of wire at both ends, spaced 1/2 inch between ends, as shown on Fig 31 . IRAUDPS1 Rev 3.3 www.irf.com Page 25 of 35 - 26 Step No. 3 Winding S1: 9. Cut 60cm of 20 AWG (0.86mm) x 3 magnet wires 10. Start winding of S1 at 90 degrees forward respect to the start point of P1, as shown on Fig 32, start is the top side, and finish is the bottom side 11. Wind 10 turns whit the three parallel wires at the same time, evenly spaced around the core on same direction as shown on Fig 32 12. Leave 4 cm of wire at both ends. Fig No. 32 . Winding S2: 13. Cut 60cm of 20 AWG (0.86mm) x 3 magnet wires 14. Start winding of S1 at 90 the end pf S1 forward respect to the start point of S1, as shown on Fig 33 15. Wind 10 turns whit the three parallel wires at the same time, evenly spaced around the core on same direction as shown on Fig 33 16. Leave 4 cm of wire at both ends. Fig No. 33 . Step No. 5 Performing "Start and Finish wires" Mounting holes; using an IR2085_MB_R2 PCB, perform the next instruction: 4 1 5 2 3 6 Fig No. 34 17. Perform "P1 Start" to fit into Pad 1 as shown Fig 6. 18. Perform "P1 finish" and "P2 Sstart" to be fitted into pad 2 as shown on Fig No. 34, this is the center tap of the Primary side 19. Perform "P2 finish", to be fitted into mounting hole 3 as shown in fig No. 6. 20. Perform "S1 start" (top winding) to be connected on Pad 4 as shown on Fig 34 21. Perform "S1 finish" wire (bottom winding) to be connected at Pad 5, this is the center tap of the secondary side 22. Perform "S2 start (top winding) to the IRAUDPS1 Rev 3.3 www.irf.com Page 26 of 35 - 27 center tap on Pad 5 23. Perform "S2 finish" of (bottom winding) to be connected to hole 6 as shown on fig 35 24. Cut and strip magnet wires for 1/2 inches long to be performed as surface mounting as shown on Fig 35 25. Thin the transformer terminals as shown on Fig 36 26. Before mounting on PCB measure inductance according to next Table 8 Fig 35 Fig 36 Fig. 37 . Table 8 Transformer's Electrical Characteristics Inductance at P1 and P2 on terminals 1,2 and 2,4 65uH-75uH Inductance difference between windings P1 and P2 1uH maximum Inductance at S1 and S2 on terminals 5,7 and 7,8 470uH minimum Inductance difference between windings S1 and S2 2uH maximum DCR at P1 winding 1,2 and P2 winding 2,4 3.0mOhms max DCR at S1 terminals 5,6 and S2 terminals 7,8 46mOhms max Number of turns for P1 and P2 4 Turns 18 AWG x 4 Number of turns for S2 and S2 10 Turns 20 AWG x 3 Leakage Inductance, with S1 and S2 shorted 1uH max Resistance between Primary and Secondary (P and Infinite S windings) Resistance between any winding and core Infinite High-Pot between primary and secondary windings 500VAC High-Pot between any winding and core 500VAC Dimensions 1.4" OD x 0.80" Height Mounting See Fig 37 . IRAUDPS1 Rev 3.3 www.irf.com Page 27 of 35 - 28 - Design Example Assume the following customer specifications are required: A 12V system automotive power supply to drive a stereo class D amplifier 300 Watts per channel into 4 ohms, and the maximum standby power consumption of the power supply should be 5 watts at 14V battery voltage with no load; also efficiency should be greater than 80%, compact design size 3 inches wide, 5 1/2 long and 1 1/2 high Voltages outputs required The first step is to calculate the output voltages and the input and output currents; the control circuits in the IRAUDPS1 are a good reference design to design the whole control system +B and -B are calculated as following: AUDIO signal VRMS = Sqrt (300W X 4 Ohms) = 34.6VRMS Thus, +B = 34.6 x 1.4142 = +50VDC and -B = -50VDC Input Current required from Battery Input Current Loaded = 300W x 2 = 600W If efficiency of the Class D amp is 90% then 600 x 1.1 = 660W If the efficiency of the power supply is 80% then 660W x 1.2 = 792W = 800W Thus, I loaded = 800W / 14V = 57A Output Current provided Total output current = 660W / 50V = 13.2A Thus +B = 13.2 / 2 = 6.6A and -B = -6.6A Transformer Design Example The transformer design is a trade-off between size, operating frequency, physical windings to achieve low leakage inductance, form factor, primary turns ratio to meet standby input current, and type of core material Core Selection Core must be selected as power material composite and it can be chosen from any major manufacturers which are Magnetics Inc, TDK, Ferroxcube, Siemens or Thomson. Each manufacturer has a number of different powder core mixes of various materials to achieve different advantages, so in this case Magnetics Inc core ZP42915TC is selected according the estimated size required to fit the power required Notice on IRADUPS1 Fig 30 and Fig 31 the primary windings are 4 turns and they are distributed equally and spaced around the core in order to provide uniform magnetic flux density therefore low leakage inductance, so 4 turns on primary side is a good practice for now because it fits most of the requirements mentioned above, of which the most important factor here is size and physical windings to achieve low leakage inductance and core material IRAUDPS1 Rev 3.3 www.irf.com Page 28 of 35 - 29 - Primary inductance Primary Inductance called here as Lp is 65uH that belongs to 4 turns according to Magnetics ZP42915TC permeability data sheet Magnetizing current The standby current with no load depends on the magnetizing idle of the power transformer called here as IM and it depends on the operating switching frequency called here as Fs Magnetizing current = IM = 5W of standby current / 14V = 0.35A Therefore this is the transformer's primary windings impedance current Thus, Transformer magnetizing impedance = ZM = 14V / 0.35A = 40 ohms Then we assume that ZM is the same impedance of XL where XL = 6.28 x Lp x Fs Therefore switching frequency = Fs = XL / (Lp x 6.28) Operating switching frequency calculation Because this is a push-pull DC-DC converter, switching frequency is calculated as follows: Operating switching frequency = Fs = 1/2 (XL / (Lp x 6.28) = 1 / 2 (6.28 x 65uH) / 40 ohms = 48.9 kHz Therefore we will use 50 kHz Verification of the computations: Transformer primary windings Impedance = XL = 6.28 x 65uH x 50 kHz = 20.41 ohms IM = 1/2 (V / XL) = 1/2 (14V / 20.41) = 0.34A Thus, the standby current will be 0.34A at 14V = 4.9W which will meet the customer's specifications Turns ratio calculations If the primary windings are 4 turns and they are distributed equally spaced around the core as shown on Fig 30 and Fig 31 Thus, Volts per turn ratio = 14V / 4 turns = 3.5V per turn Turns required on secondary = 50V / 3.5V = 14 turns Number of wires and gauge required Primary Windings Because the input current will be 57A, the wire's gauge will be the biggest possible to fit into the core with the lowest DCR possible for a maximum efficiency and lower temperature dissipation Assuming 5 watts DC power dissipation on the primary side, then Primary DCR maximum required = 5W / (57)2 = 5 / 3249 = 0.0015 ohms IRAUDPS1 Rev 3.3 www.irf.com Page 29 of 35 - 30 Wire length required is 6 inches for 4 turns in this case in particular for Magnetics Core ZP42915TC, Then considering copper DC resistance according to gauge table 9 below Thus, a single # 14 AWG magnet wire is required considering only the DC resistance (DCR), but considering the skin effect of the high frequency of operation which in this case will be 50 kHz, therefore 5 wires in parallel # 18 are required in order to minimize the skin effect and therefore minimize the AC resistance at 50 kHz . Table 9 Round copper magnet wire DCR and AC/DC Resistance ratio due to skin effect versus frequency 25kHz 50 kHz 100kHz AWG # Diameter mils DCR per 1ft m Skin depth ratio Rac / Rdc Skin depth ratio Rac / Rdc Skin depth ratio Rac / Rdc 12 81.6 1.59 4.56 1.45 6.43 1.85 9.10 2.55 14 64.7 2.52 3.61 1.30 5.09 1.54 7.21 2.00 16 51.3 4.02 2.87 1.10 4.04 1.25 4.54 1.40 18 40.7 6.39 2.27 1.05 3.20 1.15 4.54 1.40 20 32.3 10.1 1.80 1.00 2.54 1.05 3.6 1.25 22 25.6 16.2 1.48 1.00 2.02 1.00 2.85 1.10 24 20.3 25.7 1.13 1.00 1.60 1.00 2.26 1.04 26 16.1 41.0 0.90 1.00 1.27 1.00 1.79 1.00 . Secondary Windings Because the secondary current is only 6.6A, lets assume a power dissipation of 2W on the secondary windings Secondary DCR maximum rewired = 2 / (6.6) 2 = 0.045 ohms Thus, 3 wires # 20 required from table 9 MOSFTS Selection Because part of the customer specification has to be a compact design, the Direct FET IRF6648 is selected due to small package, high current capability, 60VDS, low RDSON and low Qg feature Quantity of MOSFETS required Since the input current at full load will be 57 amperes, and operating frequency is 50 kHz with 50% duty cycle (100us turn ON) and according to IRF6648 data sheet the safe operating area (Fig 12 from data sheet) Therefore, 15A will be the adequate current to be into the SOA Number of devices = 57A / 20A = 3.8 devices Thus, 4 devices required per each side of the Push-Pull transformer IRAUDPS1 Rev 3.3 www.irf.com Page 30 of 35 - 31 Gate Drive Current required The Peak Gate drive current from IRS2085 = (VCC / RGATE ) x 2 outputs = (10V/ 22 ohms) x 2 = 0.9A The average current required to drive each gate depends on the Gate drive resistor and Qg of the selected MOSFET, which in this case Qg is 50nC (nano-coulombs) from data sheet and Gate derive resistor is 22 ohms from Fig 2 R18-R21, but there are two FETS in parallel per gate drive Average Gate Current = IGATE = (VGATE / RGATE ) x 2Qg x Fs = (10V / 22) x 50E-9 x 50kHz) = 0.0022A Total Average Gate Current required = 0.0022A x 4 devices = 0.1A MOFETS Power Dissipation losses The power dissipation at DC can be calculated as following: 57A / 4 devices = 14.25A DC Power dissipation per device = I2 x RDSON / 2 Note RDSON at 100C from Data sheet Fig 5, is divided by 2 because it is 50% duty cycle Power dissipation per device = (14.25)2 x 7.5mOhms / 2 = 7.6W Total power dissipation = (57)2 x 1/4 7.5 mOhms = 3249 x 1.875 = 60.91 watts MOSFET Switching loses The MOSFETS switching losses can be calculated as following: Switching losses = Turn ONLOSSES + Turn OFFLOSSES + Gate Drive LOSSES + Gate Drive Resistor LOSSES From IRF6648 data sheet T(RISE TIME) = 29nS and T(FALL TIME) = 13nS and QSW = 17nC Losses contributed by the size of the gate series resistor Gate drive series resistors actually slowdown the turn ON and turn OFF timing (See Fig 2, R18-R21) Delay losses contributed by the gate series resistor = GRES Delay = QSW / (VCC / RGATE ) GRES Delay = 17E-9 / (10V / 22 ohms ) = 17E-9 / 0.45A = 7.65nS Turn ONLOSSES = FOSC x 1/2 x (T(RISE TIME) + GRES Delay) x I x 2VDS = 50kHz x 0.5 x (29nS + 7.65nS) x 14.25A x 28V = 0.36 watts per device Total Turn ON losses = 0.29 x 8 = 2.88W IRAUDPS1 Rev 3.3 www.irf.com Page 31 of 35 - 32 Note: VDS is multiplied by 2 because VDS occurs twice in Push-Pull converters, 1/2 is because it is working at 50% duty cycle Turn OFFLOSSES = FOSC x 1/2 (T(FALL TIME) + GRES Delay) x I x 2VDS = 50kHz x 0.5 x (13nS + 7.65nS) x 14.25A x 28V = 0.20 watts per device Total Turn ON losses = 0.20 x 8 = 1.6W Gate losses = Qg x VGATE x FOSC Qg from IRF6648 data sheet is 36nC Gate losses = 36E-9 x 10 x 50khz = 0.018W per FET Total Gate losses = 0.018W x 8 = 0.144W Total switching losses = 2.88 + 1.6 + 0.144 = 4.62W Output Rectifiers Losses +DC rectifier losses = V(DIODE) x I(OUT) = 0.7V x 6.6A = 4.62W per diode Total Diode rectifiers for +B and -B = 4.62 x 4 = 18.48 watts Efficiency Total losses then will be; Transformer losses + MOSFETS losses + switching losses + output rectifiers losses + core losses Core losses according to material P from Magnetics-Inc data sheet is 2 watts at 50 kHz Total transformer losses = Primary winding loses + Secondary winding losses + Core Losses 5W +2W + 2W +2 W = 11 watts Total MOSFET losses = RDSON losses + Switching losses = 60.91W + 4.62W = 64.81W Overall Losses = 11W + 64.81W + 18.48W = 94.29W Efficiency = 600 / 600+ 94.29 = 86.41% Therefore meet the efficiency specification IRAUDPS1 Rev 3.3 www.irf.com Page 32 of 35 - 33 - Frequency of oscillation From Fig 2, the frequency of oscillation is managed by R1 and C2 values and it shall be calculated by the equation below FOSC = 1 / R1 x C2 = 50 kHz Thus, at 50Khz if R1 is 30k, then C2 will be 470pF, said values as shown on schematic Fig 2 (See IR2085 data sheet for more details) Selecting Dead-time Dead time selection depends on the turn ON and OFF delay of the power MOSFETS selected, in this case IRF6648 data sheet shows 16nS for turn ON delay and 28nS for turn OFF delay, rise time 29nS and fall time 13nS, Therefore dead time required = 16nS + 28nS + 29nS + 13nS = 86nS per phase Because this is a push-pull then 86nS are multiplied by two giving 172uS Thus, dead time can be programmed according to the 2085 datasheet where dead time values are the relationship weight of C versus R, the biggest is C and the smallest is R. The biggest will be the dead time and vice versa Therefore, Fig 2 30K ohms and 470pF belongs to 170uS of dead time Over-Temperature Protection (OTP) Thermistor is selected to get 8.2 k ohms at 90OC, it can be readjusted changing R16 or R15 and R17 for any other temperature Over Current Protection (OCP) From Fig3; R47, R48, R49 and R54 can be calculated at any current protection desired by the following equation: OCP resistor = 0.6V / OCP current Example: If OCP desired is 20A Then ROCP = 0.6V / 20A = 0.03 ohms Thus, R47, R48, R49 and R54 will be 0.06 ohms each one because two of them are in parallel IRAUDPS1 Rev 3.3 www.irf.com Page 33 of 35 - 34 - BJT gate driver option Notice on schematic Fig 2 and their PCB layout that it is prepared for extra BJT drivers Q3-Q6 that in this case they are not populated, this is in case that the customer wants more than 4 MOSFETS in parallel for large power outputs applications Music Load NOTE, All previous calculations were made for continuous sine wave load for the safe and reliable design; the average currents and power dissipations actually will be 1/8 of power for soft music, 1/4 of power for heavy rock music and 3/8 of power with dead metal music, and 1/2 of rated power for subwoofer amplifiers Music load Input current calculations RMS Input current with constant sine wave outputs at 1 kHz all channels driven: * * * * * * IRMS SINE WAVE = 14V/800W = 57A I PEAK MUSIC = 57 x 1.4142 = 80A ISOFT MUSIC = 57A x 1/8 = 7.1A I ROCK MUSIC = 57 x 1/4 = 14.2A I HEAVY METAL MUSIC = 57A x 5/8 = 21.3A I Subwoofer = 57A x 1/2 =28A IRAUDPS1 Rev 3.3 www.irf.com Page 34 of 35 - 35 - Revision changes descriptions Revision IRAUDPS1_R3 IRAUDPS1_R3.1 IRAUDPS1_R3.2 IRAUDPS1_R3.3 Changes description Released Reviewed Tables 1, 2, 5, 7 Revised for 500W Deleted author and e-mail on schematics Date January 23, 2009 March 24, 2009 April 22, 2009 October 22, 2009 WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications are subject to change without notice. IRAUDPS1 Rev 3.3 www.irf.com Page 35 of 35