ICs for Communications ISDN Subscriber Access Controller for Terminals ISAC(R)-S TE PSB 2186 User's Manual 10.94 PEB 2186 Revision History: 10.94 Previous Releases: 11.88; 3.89; 12.89; 02.95 Page Subjects (changes since last revision) The present documentation is an editorial update of the Technical Manual 12.89 Data Classification Maximum Ratings Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Characteristics The listed characteristics are ensured over the operating range of the integrated circuit. Typical characteristics specify mean values expected over the production spread. If not otherwise specified, typical characteristics apply at TA = 25 C and the given supply voltage. Operating Range In the operating range the functions given in the circuit description are fulfilled. For detailed technical information about "Processing Guidelines" and "Quality Assurance" for ICs, see our "Product Overview". Edition 10.94 This edition was realized using the software system FrameMaker Published by Siemens AG, Breech Belittler, Marketing-Communication, Banisters 73, D-81541 Munching. Siemens AG 1994. All Rights Reserved. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. For questions on technology, delivery, and prices please contact the Offices of Semiconductor Group in Germany or the Siemens Companies and Representatives worldwide (see address list). Due to technical requirements components may contain dangerous substances. For information on the type in question please contact your nearest Siemens Office, Semiconductor Group. Siemens AG is an approved CECC manufacturer. General Information Table of Contents Page 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.1 Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2 Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.3 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.4 System Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.4.1 ISDN Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.4.2 Microprocessor Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2.1 General Functions and Device Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2.2 Interface and Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 2.3 IOM(R)-2 Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.3.1 Basic IOM(R)-2 Frame Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.3.2 IOM(R)-2 Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.3 mP Access to B and IC Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.3.4 MONITOR Channel Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 2.3.5 C/I-Channel Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 2.3.6 TIC-Bus Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 2.4 Layer-1 Functions for the S/T Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 2.4.1 S/T Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 2.4.2 Analog Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 2.4.3 S/T-Interface Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 2.4.4 S/T Interface Pre-Filter Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 2.4.5 Receiver Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 2.4.5.1 Receive Signal Oversampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 2.4.5.2 Adaptive Receiver Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 2.4.5.3 Level Detection Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2.4.6 Timing Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2.4.7 Activation/Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 2.4.7.1 FAinfA_1fr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 2.4.7.2 FAinfB_1fr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 2.4.7.3 FAinfD_1fr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 2.4.7.4 FAinfA_kfr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 2.4.7.5 FAinfB_kfr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Semiconductor Group 3 General Information Table of Contents Page 2.4.7.6 FAinfD_kfr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 2.4.7.7 FAregain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 2.4.8 D-Channel Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 2.4.9 S- and Q-Channel Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 2.5 Terminal Specific Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 2.6 Test Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 2.7 Layer-2 Functions for the ISDN-Basic Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 2.7.1 Message Transfer Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 2.7.2 Protocol Operations (auto-mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 2.7.3 Reception of Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 2.7.4 Transmission of Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 2.7.5 Documentation of the Auto Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 2.7.5.1 Legend of the Auto-Mode Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 2.7.5.2 Additional General Considerations when Using the Auto Mode . . . . . . . . . . . . . . 77 2.7.5.3 Dealing With Error Conditions in Auto Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 3 Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 3.1 Microprocessor Interface Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 3.2 Interrupt Structure and Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 3.3 Control of Layer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 3.3.1 Activation/Deactivation of IOM(R) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 3.3.2 Activation/Deactivation of S/T Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 3.3.2.1 Layer-1 Command/Indication Codes and State Diagrams . . . . . . . . . . . . . . . . . . 125 3.3.3 Example of Activation/Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 3.4 Control of Layer-2 Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 3.4.1 HDLC-Frame Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 3.4.2 HDLC-Frame Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 3.5 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 3.6 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 4 Detailed Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 4.1 HDLC Operation and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 4.1.1 Receive FIFO RFIFO Read Address 00-1FH . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 4.1.2 Transmit FIFO XFIFO Write Address 00-1FH . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 4.1.3 Interrupt Status Register ISTA Read Address 20H . . . . . . . . . . . . . . . . . . . . . . . 146 Semiconductor Group 4 General Information Table of Contents Page 4.1.4 Mask Register MASK Write Address 20H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 4.1.5 Status Register STAR Read Address 21H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 4.1.6 Command Register CMDR Write Address 21H . . . . . . . . . . . . . . . . . . . . . . . . . . 149 4.1.7 Mode Register MODE Read/Write Address 22H . . . . . . . . . . . . . . . . . . . . . . . . . 150 4.1.8 Timer Register TIMR Read/Write Address 23H . . . . . . . . . . . . . . . . . . . . . . . . . . 152 4.1.9 Extended Interrupt Register EXIR Read Address 24H . . . . . . . . . . . . . . . . . . . . 154 4.1.10 Transmit Address 1 XAD1 Write Address 24H . . . . . . . . . . . . . . . . . . . . . . . . . . 155 4.1.11 Receive Frame Byte Count Low RBCL Read Address 25H . . . . . . . . . . . . . . . . 156 4.1.12 Transmit Address 2 XAD2 Write Address 25H . . . . . . . . . . . . . . . . . . . . . . . . . . 156 4.1.13 Received SAPI Register SAPR Read Address 26H . . . . . . . . . . . . . . . . . . . . . . 156 4.1.14 SAPI1 Register SAP1 Write Address 26H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 4.1.15 Receive Status Register RSTA Read Address 27H . . . . . . . . . . . . . . . . . . . . . . 157 4.1.16 SAPI2 Register SAP2 Write Address 27H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 4.1.17 TEI1 Register 1 TEI1 Write Address 28H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 4.1.18 Receive HDLC Control Register RHCR Read Address 29H . . . . . . . . . . . . . . . . 160 4.1.19 TEI2 Register TEI2 Write Address 29H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 4.1.20 Receive Frame Byte Count High RBCH Read Address 2AH . . . . . . . . . . . . . . . 161 4.1.21 Status Register 2 STAR2 Read/Write Address 2BH . . . . . . . . . . . . . . . . . . . . . . 162 4.2 Special Purpose Registers: IOM(R)-2 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 4.2.1 Serial Port Control Register SPCR Read/Write Address 30H . . . . . . . . . . . . . . . 163 4.2.2 Command/Indication Receive 0 CIR0 Read Address 31H . . . . . . . . . . . . . . . . . 164 4.2.3 Command/Indication Transmit 0 CIX0 Write Address 31H . . . . . . . . . . . . . . . . . 165 4.2.4 MONITOR Receive Channel 0 MOR0 Read Address 32H . . . . . . . . . . . . . . . . . 166 4.2.5 MONITOR Transmit Channel 0 MOX0 Write Address 32H . . . . . . . . . . . . . . . . . 166 4.2.6 Command/Indication Receive 1 CIR1 Read Address 33H . . . . . . . . . . . . . . . . . 166 4.2.7 Command/Indication Transmit 1 CIX1 Write Address 33H . . . . . . . . . . . . . . . . . 166 4.2.8 MONITOR Receive Channel 1 MOR1 Read Address 34H . . . . . . . . . . . . . . . . . 167 4.2.9 MONITOR Transmit Channel 1 MOX1 Write Address 34H . . . . . . . . . . . . . . . . . 167 4.2.10 Channel Register 1 C1R Read/Write Address 35H . . . . . . . . . . . . . . . . . . . . . . . 167 4.2.11 Channel Register 2 C2R Read/Write Address 36H . . . . . . . . . . . . . . . . . . . . . . . 167 4.2.12 B1-Channel Register B1CR Read Address 37H . . . . . . . . . . . . . . . . . . . . . . . . . 168 4.2.13 Synchronous Transfer Control Register STCR Write Address 37H . . . . . . . . . . . 168 4.2.14 B2-Channel Register B2CR Read Address 38H . . . . . . . . . . . . . . . . . . . . . . . . . 169 Semiconductor Group 5 General Information Table of Contents Page 4.2.15 Additional Feature Register 1 ADF1 Write Address 38H . . . . . . . . . . . . . . . . . . . 170 4.2.16 Additional Feature Register 2 ADF2 Read/Write Address 39H . . . . . . . . . . . . . . 171 4.2.17 MONITOR Status Register MOSR Read Address 3AH . . . . . . . . . . . . . . . . . . . . 172 4.2.18 MONITOR Control Register MOCR Write Address 3AH . . . . . . . . . . . . . . . . . . . 172 4.2.19 S-, Q-Channel Receive Register SQRR Read Address 3BH . . . . . . . . . . . . . . . 173 4.2.20 S, Q Channel Transmit Register SQXR Write Address 3BH . . . . . . . . . . . . . . . . 174 5 Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 6 ISAC(R)-S TE Low Level Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 6.1 Architecture and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 6.2 Summary of LLC Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 6.2.1 Layer-1 Related Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 6.2.2 HDLC-Controller Related Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 6.2.3 External Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 6.3 LLC-Code Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 6.3.1 Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 6.3.2 Definitions and Naming Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 6.3.2.1 Type Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 6.3.2.2 Macro Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 6.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 6.5 LLC-Routine Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 6.5.1 ISAC(R)-S TE Layer-1 Functions: The SBC Part . . . . . . . . . . . . . . . . . . . . . . . . . . 201 6.5.2 ISAC(R)-S TE HDLC-Controller Related Functions: The ICC Part . . . . . . . . . . . . 202 6.6 Listing of Driver Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 7 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 IOM(R), IOM(R)-1, IOM(R)-2, SICOFI(R), SICOFI(R)-2, SICOFI(R)-4, SICOFI(R)-4C, SLICOFI(R), ARCOFI(R) , ARCOFI(R)-BA, ARCOFI(R)-SP, EPIC(R)-1, EPIC(R)-S, ELIC(R), IPAT(R)-2, ITAC(R), ISAC(R)-S, ISAC(R)-S TE, ISAC(R)-P, ISAC(R)-P TE, IDEC(R), SICAT(R), OCTAT(R)-P, QUAT(R)-S are registered trademarks of Siemens AG. MUSACTM-A, FALCTM54, IWETM, SARETM, UTPTTM, ASMTM, ASPTM are trademarks of Siemens AG. Purchase of Siemens I2C components conveys a license under the Philips' I2C patent to use the components in the I2C-system provided the system conforms to the I2C specifications defined by Philips. Copyright Philips 1983. Semiconductor Group 6 General Information Introduction The PSB 2186 ISAC(R)-S TE implements the four-wire S/T interface used to link voice/data terminals to an ISDN. The PSB 2186 combines the functions of the S-Bus Interface Circuit (SBC: PEB 2080) and the ISDN Communications Controller (ICC: PEB 2070) on one chip. The component switches B- and D-channels between the S/T and the ISDN Oriented Modular (IOM(R)) interfaces, the latter being a standard backplane interface for the ISDN-basic access. The device provides all electrical and logical functions of the S/T interface, such as: activation/ deactivation, mode dependent timing recovery and D-channel access and priority control. The HDLC packets of the ISDN D-channel are handled by the ISAC-S which interfaces them to the associated microcontroller. In one of its operating modes the device offers high level support of layer-2 functions of the LAPD protocol. The ISAC-S is a CMOS device, available in a P-DIP-40, P-LCC-44, P-MQFP-64 package. It operates from a single + 5 V supply and features a power-down state with very low power consumption. Semiconductor Group 7 ISDN Subscriber Access Controller for Terminals (ISAC(R)-S TE) PSB 2186 Preliminary Data 1 CMOS IC Features Terminal IOM(R)-2 terminal specific version of the PEB 2086: Pin and software compatible to PEB 2086 Compatible to PEB 2085 (Symmetrical Receiver) Full duplex 2B+D S/T interface transceiver according to CCITT I.430 Conversion of the frame structure between the S/T interface and IOM-2 Receive timing recovery D-channel access control Activation and deactivation procedures with automatic wake-up from power-down state Access to S and Q bits of S/T interface Adaptively switched receive thresholds Support of LAPD protocol FIFO buffer (2 x 64 bytes) for efficient transfer of D-channel packets 8-bit microprocessor interface, multiplexed or non-multiplexed Serial interface: IOM-2 interface including bit clock and strobe signal Implementation of IOM-2 MONITOR and C/I-channel protocol to control peripheral devices Microprocessor access to B- and intercommunicationchannels Watchdog timer Advanced CMOS technology Low power consumption: standby: 8 mW; active: 80 mW P-MQFP-64 P-LCC-44 P-DIP-40 Type Ordering Code Package PSB 2186H Q67100-H6412 P-MQFP-64 (SMD) PSB 2186N Q67100-H6390 P-LCC-44 (SMD) PSB 2186P Q67100-H6389 P-DIP-40 The PSB 2186, ISAC-S TE is software compatible to the PEB 2085, ISAC-S. Semiconductor Group 8 10.94 Features Pin Configuration (top view) 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 32 31 51 30 52 29 53 54 28 27 55 26 56 25 PSB 2186 57 24 58 23 59 22 60 21 61 20 62 19 16 15 14 13 12 11 10 9 8 7 6 5 N.C. N.C. A0 RD(DS) WR(R/W) CS ALE IDP1 (DU) IDP0 (DD) SX2 SX1 VDD N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. VSSD BCL INT N.C. VSSA XTAL2 XTAL1 VDD SR2 N.C. SR1 4 17 3 18 64 2 63 1 N.C. A2 A1 SDS1 N.C. RST A5 EAW VSSD DCL FSC1 N.C. VSSD N.C. A4 A3 48 N.C. N.C. N.C. N.C. AD7 /D7 AD6 /D6 AD5 /D5 AD4 /D4 AD3 /D3 AD2 /D2 AD1 /D1 AD0 /D0 N.C. N.C. N.C. N.C. P-MQFP-64 A1 A2 AD7/ D7 AD6/ D6 AD5/ D5 AD4/ D4 AD3/ D3 AD2/ D2 AD1/ D1 AD0/D0 A0 P-LCC-44 6 SDS1 N.C. RST EAW/A5 VSSD DCL FSC1 N.C. VSSD 4 3 2 1 44 43 42 41 40 39 8 38 9 37 10 36 11 35 12 PSB 2186 Semiconductor Group 34 13 33 14 32 15 31 16 30 17 18 19 20 21 22 23 24 25 26 27 28 A3 N.C. N.C. V SSD BCL INT V SSA XTAL2 XTAL1 SR2 SR1 N.C. A4 5 7 9 29 RD(DS) WR(R/W) CS ALE IDP1 (DU) IDP0 (DD) SX2 SX1 VDD N.C. N.C. ITP04471 ITP04470 Features Pin Configuration (top view) P-DIP-40 AD4 1 40 AD3 AD5 2 39 AD2 AD6 3 38 AD1 AD7 4 37 AD0 N.C. 5 36 RD SDS1 6 35 WR N.C. 7 34 CS RST 8 33 ALE EAW 9 32 IDP1 (DU) VSSD 10 31 IDP0 (DD) DCL 11 30 SX2 FSC1 12 29 SX1 N.C. 13 28 V DD VSSD 14 27 N.C. N.C. 15 26 N.C. N.C. 16 25 SR1 N.C. 17 24 SR2 VSSD 18 23 XTAL1 BCL 19 22 XTAL2 INT 20 21 VSSA PSB 2186 ITP04469 Semiconductor Group 10 Features 1.1 Pin Definitions and Functions Pin No. P-DIP-40 Pin No. Pin No. Symbol P-MQFP-64 P-LCC-44 37 38 39 40 1 2 3 4 37 38 39 40 41 42 43 44 41 42 43 44 1 2 3 4 AD0/D0 AD1/D1 AD2/D2 AD3/D3 AD4/D4 AD5/D5 AD6/D6 AD7/D7 Input (I) Output (O) Open Drain (OD) I/O I/O I/O I/O I/O I/O I/O I/O 34 27 37 CS I - 28 38 R/W I 35 28 38 WR I - 29 39 DS I 36 29 39 RD I 20 8 23 INT OD Semiconductor Group 11 Function Multiplexed Bus Mode: Address/data bus transfers addresses from the P system to the ISAC-S TE and data between the P system and the ISAC-S TE. Non-Multiplexed Bus Mode: Data bus. Transfers data between the P system and the ISAC-S TE. Chip Select: A "Low" on this line selects the ISAC-S TE for a read/write operation. Read/Write: When "High" identifies a valid P access as a read operation. When "Low", identifies a valid P access as a write operation (Motorola bus mode). Write: This signal indicates a write operation (Intel bus mode). Data Strobe: The rising edge marks the end of a valid read or write operation (Motorola bus mode). Read: This signal indicates a read operation (Intel bus mode). Interrupt Request: The signal is activated when the ISAC-S TE requests an interrupt. It is an open drain output. Features 1.1 Pin Definitions and Functions (cont'd) Pin No. P-DIP-40 Pin No. Pin No. Symbol P-MQFP-64 P-LCC-44 33 26 36 ALE 8 54 9 RST 12 59 13 FSC1 11 58 12 DCL - - - - - - 30 51 50 64 63 55 40 6 5 18 17 10 A0 A1 A2 A3 A4 A5 Semiconductor Group 12 Input (I) Function Output (O) Open Drain (OD) I Address Latch Enable: A high on this line indicates an address on the address/data bus (multiplexed bus type only). ALE also selects the microprocessor interface type (multiplexed or nonmultiplexed) P-LCC and P-MQFP only. I/O Reset: A "High" on this input forces the ISAC-S TE into reset state. The minimum pulse length is four DCL-clock periods or four ms. If the terminal specific functions are enabled, the ISAC-S TE may also supply a reset signal. O (I) Frame Sync 1: Frame sync output. "High" during channel 0 on the IOM-2 interface. FSC1 becomes Input if Test Mode is programmed (ADF1). O (I) Data Clock: Clock of frequency equal to twice the data rate on the IOM-interface Clock output 1536-kHz IOM-2 mode DCL becomes Input if Test Mode is programmed (ADF1). I Address Bit 0 I Address Bit 1 I Address Bit 2(Non-multiplexed I Address Bit 3bus mode) I Address Bit 4 I Address Bit 5 Features 1.1 Pin Definitions and Functions (cont'd) Pin No. P-DIP-40 Pin No. Pin No. Symbol P-MQFP-64 P-LCC-44 9 56 10 EAW 6 52 7 SDS1 19 7 22 BCL 10, 14, 18 57, 6, 61 11, 15, 21 VSSD Input (I) Function Output (O) Open Drain (OD) I External Awake (terminal specific function). If a falling edge on this input is detected, the ISAC-S TE generates an interrupt and, if enabled, a reset pulse. O Serial Data Strobe 1. A programmable strobe signal, selecting either one or two Bor IC-channels on IOM-2 interface, is supplied via this line. After reset, SDS1 takes on its function only after a write access to SPCR is made. O Bit Clock: Clock of frequency 768 kHz, IOM-2 mode. - Digital ground 21 10 24 - Analog ground 28 13, 21 31 VSSA VDD - Power supply (5 V 5 %) 23 12 26 XTAL1 I 22 11 25 XTAL2 O 24 25 29 14 16 22 27 28 32 SR2 SR1 SX1 I I O 30 23 33 SX2 O 31 32 24 25 34 35 IDP0(DD) I/O IDP1(DU) I/O Connection for crystal or external clock input Connection for external crystal. Left unconnected if external clock is used. S-Bus Receiver Input S-Bus Receiver Input S-Bus Transmitter Output (positive) S-Bus Transmitter Output (negative) IOM-Data Port 0 (DD) IOM-Data Port 1 (DU) Open drain without internal pull-up resistor or push-pull (ADF2:ODS) Semiconductor Group 13 Features 1.2 Logic Symbol 0V Reset 7.68 MHz 100 ppm VDD VSSA VSSD RST XTAL1 +5V 0V SR2 IDP0 (DD) R IOM -2 XTAL2 TR = 100 *) IDP1 (DU) SR1 EAW S/T FSC1 SX2 DCL Clock Frame Synchronization TR = 100 *) BCL SX1 SDS1 AD0...7 (D0...7) WR RD (A0...5) CS (R/W) (DS) INT ALE P *) Terminating resistors only at the far ends of the connection Figure 1 Logic Symbol of the ISAC(R)-S TE PSB 2186 Semiconductor Group 14 ITL04472 Features 1.3 Functional Block Diagram R IOM -2 S B-Channel Buffer Switching R IOM Interface ISDN Basic Access Layer-1 Functions D-Channel Handling Control FIFO P Interface ITB05406 P Figure 2 Block Diagram of the ISAC(R)-S TE Semiconductor Group 15 Features 1.4 System Integration 1.4.1 ISDN Applications The reference model for the ISDN-basic access according to CCITT I series recommendations consists of - an exchange and trunk line termination in the central office (ET, LT) - a remote network termination in the user area (NT) - a two-wire loop (U interface) between NT and LT - a four-wire link (S interface) which connects subscriber terminals and the NT in the user area as depicted in figure 3. ISDN User Area TE ISDN Central Office U S NT LT NT1 NT2 ET NT1 T TE ITS02314 Figure 3 ISDN-Basic Subscriber Access Architecture The NT equipment serves as a converter between the U interface at the exchange and the S interface at the user premises. The NT may consist of either an NT1 only or an NT1 together with an NT2 connected via the T interface which is physically identical to the S interface. The NT1 is a direct transformation between layer 1 of S and layer 1 of U. NT2 may include higher level functions like multiplexing and switching as in a PBX. The ISAC-S TE is designed for the user area of the ISDN-basic access, especially for subscriber terminal equipment with S interfaces. Figure 4 illustrates the application of the ISAC-S TE. Semiconductor Group 16 Features PBX (NT2) TE(1) S CP TE(8) SN TE(1) U T LT-S LT-T NT1 LT-S CP = Central Processor Line Card TE(1) TE(8) R SN = Switching Network Direct Subscriber Access (point-to-point, short and extended passive Bus) = ISAC -S TE U S NT1 ITS05407 Figure 4 Applications of the ISAC(R)-S TE (ISDN-Basic Access) Terminal Applications The concept of the ISDN basic access is based on two circuit-switched 64 kbit/s B channels and a message oriented 16 kbit/s D channel for packetized data, signaling and telemetry information. Figure 5 shows an example of an integrated multifunctional ISDN-S terminal using the ISAC-S TE. The ISAC-S TE provides the interface to the bus and separates the B- and D channels. The D channel, containing signaling data and packet switched data, is processed by the LAPD controller contained in the ISAC-S TE and routed via a parallel P interface to the terminal processor. The high level support of the LAPD protocol which is implemented by the ISAC-S TE allows the use of a low cost processor in cost sensitive applications. The IOM-2 interface generated by the ISAC-S TE is used to connect different voice/data (V/D) application modules: - sources/sinks for the D channel - sources/sinks for the B1- and B2 channels. Semiconductor Group 17 Features R IOM -2 D,C/I R ICC PEB 2070 ISAC -S TE PSB 2186 B1 B2 IC1 Speech Processing DSP-COFI IC2 Data Encryption HSCX SAB 8252X C Data Module Speech Modules Data Modules ITD05408 Figure 5 Example of an ISDN(R)-S TE Voice/Data Terminal Up to eight D-channel components (ICC: ISDN Communication Controller PEB 2070) may be connected to the D- and C/I (Command/Indication) channels (TIC-bus). The ISAC-S TE and ICC handle contention autonomously. Data transfers between the ISAC-S TE and the voice/data modules are done with the help of the IOM-MONITOR channel protocol. Each V/D module can be accessed by an individual address. The same protocol enables the control of IOM-terminal modules and the allocation of intercommunication channels inside the terminal. Two intercommunication channels IC1 and IC2 allow a 2 x 64 kbit/s transfer rate between voice/data modules. In the example above (figure 5), one ICC is used for data packets in the D channel. A voice processor is connected to a programmable digital signal processing codec filter via IC1 and a data encryption module to a data device via IC2. B1 is used for voice communication, B2 for data communication. Figure 6 shows the implementation of a ISDN feature phone using the ISAC-S TE and the Audio Ringing Codec Filter featuring speakerphone (PSB 2165, ARCOFI-SP). Semiconductor Group 18 Features PSB 2165 ARCOFI R -SP R IOM -2 LCD Control LCD Display PSB 2186 R ISAC -S TE 80C51 80C188 S-Bus Power Controller PSB 2120 IRPC ITS05409 Figure 6 ISDN-Feature Telephone 1.4.2 Microprocessor Environment The ISAC-S TE is especially suitable for cost-sensitive applications with single-chip microcontrollers (e.g. 8048, 8031, 8051). However, due to its programmable micro- processor interface and non-critical bus timing, it fits perfectly into almost any 8-bit microprocessor system environment. The microcontroller interface can be selected to be either of the Motorola type (with control signals CS, R/W, DS) of the Siemens/Intel non-multiplexed bus type (with control signals CS, WR, RD) or of the Siemens/Intel multiplexed address/data bus type (CS, WR, RD, ALE). An example how to connect the ISAC-S TE to a Siemens/Intel microcontroller is shown in figure 7. Semiconductor Group 19 Features IOM R -2 +5V INT(INTX) INT RD RD WR ALE ALE 80C51 (80C188) RD WR WR S0 (PSCX) ALE CS R ISAC -S TE PSB 2186 SX1 SX2 SR1 SR2 A15 ... A8 AD ... AD0 A8 - A15 AD0 - AD7 AD7 ... AD0 Latch Common Bus A15 - A0, D7 - D0 ITS05410 Memory Figure 7 Connecting the ISAC(R)-S TE to Siemens/Intel Microcontroller Semiconductor Group 20 Functional Description 2 Functional Description 2.1 General Functions and Device Architecture The functional block diagram of the ISAC-S TE is shown in figure 8. The left-hand side of the diagram contains the layer-1 functions, according to CCITT I series recommendations: - S-bus transmitter and receiver - timing recovery and synchronization by means of digital PLL circuitry - activation/deactivation - access to S and Q channels - handling of D channel - test loops - send single/continuous AMI pulses (diagnostics). IDP1 (DU) IDP0 (DD) SX1 AMI BIN Buffer SX2 R IOM -2 Interface D-CH Access V SSA HDLC Receiver HDLC Transmitter Control R-FIFO SR2 AMI BIN X-FIFO LAPD Controller Status Command Register FIFO Controller V DD V SS D Buffer RST SR1 XTAL1 Timing DPLL P - Interface XTAL0 ITS05411 BCL DCL FSC1 SDS1 Figure 8 Architecture of the ISAC(R)-S TE Semiconductor Group 21 AD0 - AD7 A0 - A5& D0 - D7 Control INT Functional Description The right-hand side consists of: - the serial interface logic for the IOM-2 interfaces, with B-channel switching capabilities - the logic necessary to handle the D-channel messages (layer 2). The latter consists of an HDLC receiver and an HDLC transmitter together with 64-byte deep FIFO's for efficient transfer of the messages to/from the user's CPU. In a special HDLC-controller operating mode, the auto mode, the ISAC-S TE processes protocol handshakes (I- and S frames) of the LAPD (Link Access Procedure on the D channel) autonomously. Control and monitor functions as well as data transfers between the user's CPU and the D- and B channels are performed by the 8-bit parallel P-interface logic. The IOM interface allows interaction between layer-1 and layer-2 functions. It implements D-channel collision resolution for connecting other layer-2 devices to the IOM interface (TIC bus), and the C/I and MONITOR channel protocols (IOM-2) to control peripheral devices. The timing unit is responsible for the system clock and frame synchronization. 2.2 Interface and Operating Modes The ISAC-S TE is configurable for the following application: - ISDN terminals TE mode IOM(R)-2 Interface Mode (ADF2:IMS=1) In this mode the IOM interface has the enhanced functionality of IOM-2. B-channel interfacing is performed directly via the IOM-2 interface. The ISAC-S TE supports the IOM-2 terminal mode frame structure (3 channels) according to figure 11 (see chapter 2.3.1). The operating mode is shown in table 1. Table 1 Operating Mode and Functions of Specific Pins of the ISAC(R)-S PSB 2186 in IOM(R)-2 Mode Pin No. P-DIP-40-2 11 12 19 Pin No. P-LCC-44-1 12 13 22 Pin No. P-MQFP-64-1 58 59 7 Application DCL FSC1 BCL TE o:1536 kHz* o:8 kHz* o:768 kHz* *) synchronized to the S/T interface Semiconductor Group o:output 22 Functional Description The operating mode in relation to the timing recovery is illustrated in figure 9. TE Mode, Terminal Timing Mode CLOCK MASTER 768 kbit/s 768 kbit/s IDP0 (DD) IDP1 (DU) V/D Module DCL R ISAC -S TE PSB 2186 FSC1 BCL SDS1 1536 kHz 8 kHz 768 kHz 8 kHz S ITS05412 Figure 9 Operating Modes of ISAC(R)-S TE (IOM(R)-2) Semiconductor Group 23 Functional Description 2.3 IOM(R)-2 Mode Functions 2.3.1 Basic IOM(R)-2 Frame Structure The IOM-2 is a generalization and enhancement of the IOM-1. While the basic frame structure is very similar, IOM-2 offers further capacity for the transfer of maintenance information. In terminal applications, the IOM-2 constitutes a powerful backplane bus offering intercommunication and sophisticated control capabilities for peripheral modules. The channel structure of the IOM-2 is depicted in figure 10. B1 B2 MONITOR D C/ M M R X ITD05672 Figure 10 Channel Structure of IOM(R)-2 The 64-kbit/s channels, B1 and B2, are conveyed in the first two octets. The third octet (monitor channel) is used for transferring maintenance information between the layer-1 functional blocks (SBCX, IECQ) and the layer-2 controller (see chapter 2.3.4). The fourth octet (control channel) contains - two bits for the 16-kbit/s D channel - four command/indication bits for controlling activation/deactivation and for additional control functions - two bits MR and MX for supporting the handling of the MONITOR channel. Semiconductor Group 24 Functional Description IOM(R)-2 TE Frame Structure The frame is composed of three channels (figure 11): Channel 0 contains 144 kbit/s (for 2B+D) plus MONITOR and command/indication channels for the layer-1 device. Channel 1 contains two 64-kbit/s intercommunication channels plus MONITOR and command/indication channels for other IOM-2 devices. Channel 2 is used for IOM-bus arbitration (access to the TIC bus). Only the command/ indication bits are used in channel 2. See section 2.3.6 for details. 125 s FSC1 R R IOM -2 CH0 IPD0 (DD) B1 B2 MON0 D CI0 MR IPD1 (DU) B1 B2 R IOM -2 CH1 MON0 D CI0 MR IC1 IC2 MON1 MX IC1 IOM -2 CH2 CI1 MR IC2 MX MON1 MX S/G MX BAC A/B CI1 MR TAD SDS1 ITD05413 Figure 11 Definition of IOM(R)-2 Channels in Terminal Timing Mode The IOM-2 signals are: IDP0, 1 DCL FSC1 : 768 kbit/s : 1536-kHz output : 8-kHz output. In addition, to support standard combos/data devices the following signals are generated as outputs: BCL SDS1 : 768-kHz bit clock : 8-kHz programmable data strobe signal for selecting one or both B/IC channel(s). Semiconductor Group 25 Functional Description 2.3.2 IOM(R)-2 Interface Connections Output Driver Selection The type of the IOM output is selectable via bit ODS (ADF2 register). Thus when inactive (not transmitting) IDP0, 1 are either high impedance (ODS=1) or open drain "1" (ODS=0). Normally the IOM-2 interface is operated in the "open drain" mode (ODS=0) in order to take advantage of the bus capability. In this case pull-up resistors (1 k - 5 k) are required on IDP0 and IDP1. IOM(R) OFF Function In IOM-2 terminal mode (SPCR:SPM=0) the IOM interface can be switched off for external devices via IOF bit in ADF1 register. If IOF=1, the interface is switched off i.e. DCL, FSC1, IDP0/1 and BCL are high impedance. IOM(R) Direction Control For test applications, the direction of IDP0(DD) and IDP1(DU) can be reversed during certain time-slots within the IOM-2 frame. This is performed via the IDC bit in the SQXR register. For normal operation SQXR:IDC should be set to "0". Semiconductor Group 26 Functional Description IOM(R) Data Ports in Terminal Mode In this case the IOM has the 12-byte frame structure consisting of channels 0, 1 and 2 (see figure 11): - IDP0 carries the 2B+D channels from the S/T interface, and the MONITOR 0 and C/I 0 channels coming from the S/T controller; - IDP1 carries the MONITOR 0 and C/I 0 channels to the layer-1. Channel 1 of the IOM interface is used for internal communication in terminal applications. Two cases have to be distinguished, according to whether the ISAC-S TE is operated as a master device (communication with slave devices via MONITOR 1 and C/I 1), or as a slave device (communication with one master via MONITOR 1 and C/I 1). If IDC is set to "0" (master mode): - IDP0 carries the MONITOR 1 and C/I 1 channels as output to peripheral (voice/data) devices; - IDP0 carries the IC channels as output to other devices, if programmed (CxC1 - 0 = 01 in register SPCR). If IDC is set to "1" (slave mode): - IDP1 carries the MONITOR 1 and C/I 1 channels as output to a master device; - IDP0 carries the IC channels as output to other devices, if programmed (CxC1 - 0 = 01 in register SPCR). If required (cf. DIM2-0, MODE register), bit 5 of the last byte in channel 2 on IDP0 is used to indicate the S-bus state (stop/go bit) and bits 2 to 5 of the last byte are used for TIC-bus access arbitration (see chapter 2.3.6). Figure 12 shows the connection in a multifunctional terminal with the ISAC-S TE as a master (figure 12b) and an ICC as a slave device. Semiconductor Group 27 Functional Description R ISAC -S TE S/T Interface R IOM -2 Interface Layer 1 (SBC) IDP0 (DD) IDP1 (DU) IDP0 IDP1 DD DU MON1, C/I1, IC1, IC2 2B + D, C/I0, MON0, S/G, TIC R ISAC -S TE in Master Mode (IDC = 0) IDP0 IDP1 (DD) (DU) IDP0 IDP1 Layer 2 (ICC) Voice/Data Module ITS05414 Master C Slave Figure 12a IOM(R) Data Ports 0, 1 in Terminal Mode (SPCR:SPM=0) Semiconductor Group 28 e.g. PEB 2070 (ICC) in Slave Mode (IDC = 1) Functional Description (a) Master Mode (IDC = 0) CH0 CH1 MR IPD0 (DD) B1 B2 MON0 D CI0 R S/T IOM -2 Layer 1 Layer 2 MR IPD1 (DU) B1 R IOM -2 B2 MON0 D CI0 S/T Layer 2 Layer 1 CH2 MX MR IC1 IC2 MON1 IC Transmit if Progr. Layer 2 MX CI1 R IOM -2 MR IC1 IC2 IC Receive if Progr. MON1 S/G A/B MX BAC TAD MX CI1 TIC-Bus R IOM -2 Layer 2 (b) Slave Mode (IDC = 1) CH0 CH1 MR IPD0 (DD) B1 B2 MON0 D CI0 MR IC1 IC2 MON1 MX S/G A/B CI1 R S/T IOM -2 Layer 1 B1 R IOM -2 B2 MON0 D CI0 S/T Layer 2 if Progr. Layer 2 MR IPD1 (DU) CH2 MX Layer 1 R IOM -2 MX IC1 MR IC2 IC Transmit if Progr. Figure 12b Semiconductor Group Layer 2 29 MON1 MX BAC TAD CI1 TIC-Bus Layer 2 R IOM -2 ITD05415 Functional Description P Access to B and IC Channels 2.3.3 The microprocessor can access the B and IC (intercommunication) channels at the IOM-2 interface by reading the B1CR/B2CR or by reading and writing the C1R/C2R registers. Furthermore it is possible to loop back the B channels from/to the S/T interface or to loop back the IC channels from/to the IOM-2 interface without P intervention. These access and switching functions are selected with the channel connect bits (CxC1, CxC0) in the SPCR register (table 2, figure 13). External B-channel sources (voice/data modules) connected to the IOM-2 interface can be disconnected with the IOM off function (ADF1:IOF) in order to not disturb the B-channel access (see figure 13). If the B-channel access is used for transferring 64-kbit/s voice/data information directly from the P port to the ISDN S/T interface, the access can be synchronized to the IOM interface by means of a synchronous transfer interrupt programmed in the STCR register. Table 2 Access to B/IC Channels (IOM(R)-2) P CxC1 CxC0 CxR CxR BxCR Read Write Read Output Applications to IOM-2 0 0 ICx - Bx - Bx monitoring, ICx monitoring 0 1 ICx ICx Bx ICx Bx monitoring, ICx looping from/to IOM-2 1 0 - Bx Bx Bx Bx access from/to S0; transmission of a constant value in Bx channel to S0 1 1 Bx Bx - Bx Bx looping from S0; transmission of a variable pattern in Bx channel to S0 Note: x=1 for channel 1 or 2 for channel 2 The general sequence of operations to access the B/IC channels is: (set configuration register SPCR) Program synchronous interrupt (ST0) SIN - > Read register (BxCR, CxR) (write register) Acknowledge SIN (SC0) Semiconductor Group 30 Functional Description R ISAC -S TE R IOM -2 Interface S/T Interface IDP0 (DD) IDP1 (DU) Layer-1 Functions Register: C1R/C2R B1CR/B2CR SPCR ADF1 : IOF R (IOM off) P Interface ITS05416 Figure 13 Principle of B/IC-Channel Access Semiconductor Group 31 Functional Description R IOM -2 Interface S/T Interface IDP0 (DD) IDP1 (DU) Layer-1 Functions ICx Bx BxCR CxR P ITS05417 FSC IDPO (DD) B1 B2 IC1 IC2 B1CR B2CR IDP1 (DU) B1 B2 B1 B2 IC1 IC2 B1 B2 IC1 IC2 C2R C1R IC1 IC2 ITD05402 ST0 SC0 = 1 Figure 14 Access to B and IC Channels in IOM(R)-2 Terminal Mode (a) SPCR:CxC1, CxC0 = 00 Bx monitoring, ICx monitoring (SQXR:IDC=0) Semiconductor Group 32 Functional Description R IOM -2 Interface S/T Interface IDP0 (DD) IDP1 (DU) Layer-1 Functions Bx ICx BxCR CxR P ITS05418 FSC IDPO (DD) B1 B2 IC1 IC2 B1CR B2CR IDP1 (DU) B1 B2 B1 B2 IC1 IC2 B1 B2 IC1 IC2 C2R C1R IC1 IC2 ITD05403 ST0 SC0 = 1 (b) SPCR:CxC1, CxC0 = 01 Bx monitoring, ICx looping (SQXR:IDC=0) Semiconductor Group 33 Functional Description R IOM -2 Interface S/T Interface IDP0 (DD) IDP1 (DU) Layer-1 Functions Bx Bx BxCR CxR P ITS05419 FSC IDPO (DD) B1 B2 B1CR IDP1 (DU) IC1 IC2 B1 B2 IC1 IC2 B1 B2 IC1 IC2 C1R B2CR C2R B1 B2 IC1 IC2 ITD05404 ST0 SC0 = 1 (c) SPCR:CxC1, CxC0 = 10 Bx access from/to S/T transmission of constant value to S/T Semiconductor Group 34 Functional Description R IOM -2 Interface S/T Interface IDP0 (DD) IDP1 (DU) Layer-1 Functions Bx Bx CxR P ITS05420 FSC IDPO (DD) B1 B2 IC1 IC2 B1 B2 IC1 IC2 IC1 IC2 B1 B2 IC1 IC2 B1CR B2CR IDP1 (DU) B1 B2 ITD05405 ST0 SC0 = 1 (d) SPCR:CxC1, CxC0 = 11 Bx looping from/to S/T transmission of variable pattern to S/T Semiconductor Group 35 Functional Description 2.3.4 MONITOR Channel Handling In IOM-2 mode, the MONITOR channel protocol is a handshake protocol used for high speed information exchange between the ISAC-S TE and other devices, in MONITOR channel "0" or "1" (see figure 11). In the non-TE mode, only one MONITOR channel is available ("MONITOR channel 0"). The MONITOR channel protocol is necessary: For programming and controlling devices attached to the IOM. Examples of such devices are: layer-1 transceivers (using MONITOR channel 0), and peripheral V/D modules that do not need a parallel microcontroller interface (MONITOR channel 1), such as the Audio Ringing Codec Filter PSB 2165. For data exchange between two microcontroller systems attached to two different devices on one IOM-2 backplane. Use of the MONITOR channel avoids the necessity of a dedicated serial communication path between the two systems. This greatly simplifies the system design of terminal equipment (figure 17). Note: There is normally no necessity for monitor channel operations over "MONITOR channel 0" since the internal layer-1 part of the ISAC-S TE does not support this function. The implemented MONITOR handler can however be used with external layer-1 transceivers in case only the ICC part of the ISAC-S TE is used (ADF1:TEM). Semiconductor Group 36 Functional Description R IOM -2 Data Communication (MONITOR1) Control (MONITOR1) V/D Module V/D Module R ITAC PSB 2110 R ARCOFI PSB 2160 R ARCOFI -SP PSB 2165 C R ISAC -S TE PSB 2186 C ITS05421 Figure 15 Examples of MONITOR Channel Applications in IOM(R)-2 TE Mode The MONITOR channel operates on an asynchronous basis. While data transfers on the bus take place synchronized to frame sync, the flow of data is controlled by a handshake procedure using the MONITOR Channel Receive (MR0 or 1) and MONITOR Channel Transmit (MX0 or 1) bits. For example: data is placed onto the MONITOR channel and the MX bit is activated. This data will be transmitted repeatedly once per 8-kHz frame until the transfer is acknowledged via the MR bit. The microprocessor may either enforce a "1" (idle) in MR, MX by setting the control bit MRC1, 0 or MXC1, 0 to "0" (MONITOR Control Register MOCR), or enable the control of these bits internally by the ISAC-S TE according to the MONITOR channel protocol. Thus, before a data exchange can begin, the control bit MRC(1, 0) or MXC(1, 0) should be set to "1" by the microprocessor. The MONITOR channel protocol is illustrated in figure 16. Since the protocol is identical in MONITOR channel 0 and MONITOR channel 1 (available in TE mode only), the index 0 or 1 has been left out in the illustration. The relevant status bits are: MONITOR Channel Data Received MDR (MDR0, MDR1) MONITOR Channel End of Reception MER (MER0, MER1) for the reception of MONITOR data, and MONITOR Channel Data Acknowledged MDA (MDA0, MDA1) MONITOR Channel Data Abort MAB (MAB0, MAB1) for the transmission of MONITOR data (register: MOSR) In addition, the status bit: MONITOR Channel Active MAC (MAC0, MAC1) indicates whether a transmission is in progress (register: STAR). Semiconductor Group 37 Functional Description P Transmitter MON MXE = 1 MOX = ADR MXC = 1 MAC = 1 MDA Int. MOX = DATA1 MDA Int. MOX = DATA2 MDA Int. MXC = 0 P Receiver MX MR FF FF ADR 1 1 0 1 1 1 ADR DATA1 DATA1 0 1 0 0 0 0 DATA1 DATA1 0 0 1 0 DATA2 DATA2 1 0 0 0 DATA2 DATA2 0 0 1 0 FF FF 1 1 0 0 FF FF 1 1 1 1 125 s MDR Int. RD MOR ( = ADR ) MRC = 1 MDR Int. RD MOR ( = DATA1 ) MDR Int. RD MOR ( = DATA2 ) MER Int. MRC = 0 MAC = 0 ITD00870 Figure 16 MONITOR Channel Protocol (IOM(R)-2) Semiconductor Group 38 Functional Description Before starting a transmission, the microprocessor should verify that the transmitter is inactive, i.e. that a possible previous transmission has been terminated. This is indicated by a "0" in the MONITOR Channel Active MAC status bit. After having written the MONITOR Data Transmit (MOX) register, the microprocessor sets the MONITOR Transmit Control bit MXC to "1". This enables the MX bit to go active (0), indicating the presence of valid MONITOR data (contents of MOX) in the corresponding frame. As a result, the receiving device stores the MONITOR byte in its MONITOR Receive MOR register and generates an MDR interrupt status. Alerted by the MDR interrupt, the microprocessor reads the MONITOR Receive (MOR) register. When it is ready to accept data (e.g. based on the value in MOR, which in a point-tomultipoint application might be the address of the destination device), it sets the MR control bit MRC to "1" to enable the receiver to store succeeding MONITOR channel bytes and acknowledge them according to the MONITOR channel protocol. In addition, it enables other MONITOR channel interrupts by setting MONITOR Interrupt Enable to "1". As a result, the first MONITOR byte is acknowledged by the receiving device setting the MR bit to "0". This causes a MONITOR Data Acknowledge MDA-interrupt status at the transmitter. A new MONITOR data byte can now be written by the microprocessor in MOX. The MX bit is still in the active (0) state. The transmitter indicates a new byte in the MONITOR channel by returning the MX bit active after sending it once in the inactive state. As a result, the receiver stores the MONITOR byte in MOR and generates a new MDR-interrupt status. When the microprocessor has read the MOR register, the receiver acknowledges the data by returning the MR bit active after sending it once in the inactive state. This in turn causes the transmitter to generate an MDA-interrupt status. This "MDA interrupt - write data - MDR interrupt - read data - MDA interrupt" handshake is repeated as long as the transmitter has data to send. Note that the MONITOR channel protocol imposes no maximum reaction times to the microprocessor. When the last byte has been acknowledged by the receiver (MDA-interrupt status), the microprocessor sets the MONITOR Transmit Control bit MXC to "0". This enforces an inactive ("1") state in the MX bit. Two frames of MX inactive signifies the end of a message. Thus, a MONITOR Channel End of Reception MER-interrupt status is generated by the receiver when the MX bit is received in the inactive state in two consecutive frames. As a result, the microprocessor sets the MR control bit MRC to 0, which in turn enforces an inactive state in the MR bit. This marks the end of the transmission, making the MONITOR Channel Active MAC bit return to "0". During a transmission process, it is possible for the receiver to ask a transmission to be aborted by sending an inactive MR bit value in two consecutive frames. This is effected by the microprocessor writing the MR control bit MRC to "0". An aborted transmission is indicated by a MONITOR Channel Data Abort MAB-interrupt status at the transmitter. Semiconductor Group 39 Functional Description 2.3.5 C/I-Channel Handling The command/indication channel carries real-time status information between the ISAC-S TE and another device connected to the IOM. 1) One C/I channel (called C/I0) conveys the commands and indications between the layer-1 and the layer-2 parts of the ISAC-S TE. It can be accessed by an external layer-2 device e.g. to control the layer-1 activation/deactivation procedures. C/I0 channel access may be arbitrated via the TIC bus access protocol. In this case the arbitration is done in C/I channel 2 (see figure 11). The C/I0 channel is accessed via register CIR0 (in receive direction, layer-1 to layer-2) and register CIX0 (in transmit direction, layer-2 to layer-1). The C/I0 code is four bits long. A listing and explanation of the layer-1 C/I codes can be found in chapter 3.4. In the receive direction, the code from layer-1 is continuously monitored, with an interrupt being generated anytime a change occurs (ISTA:CISQ). A new code must be found in two consecutive IOM frames to be considered valid and to trigger a C/I code change interrupt status (double last look criterion). In the transmit direction, the code written in CIX0 is continuously transmitted in C/I0. 2) A second C/I channel (called C/I1) can be used to convey real time status information between the ISAC-S TE and various non-layer-1 peripheral devices e.g. PSB 2160 ARCOFI. The channel consists of six bits in each direction (see figure 11). The C/I1 channel is accessed via registers CIR1 and CIX1. A change in the received C/I1 code is indicated by an interrupt status without double last look criterion. Semiconductor Group 40 Functional Description R P IOM -2 ICC (7) B-Channel Voice/Data Communication with D-Channel Signaling ICC (1) TIC-Bus D-Channel Telemetry/ Packet Communication B-Channel Voice/Data Communication with D-Channel Signaling CCITT S-Interface R ISAC -S TE ITS05673 Figure 17 Applications of TIC Bus in IOM(R)-2 Bus Configuration 2.3.6 TIC-Bus Access In IOM-2 interface mode the TIC-bus capability is only available in TE mode. The arbitration mechanism implemented in the last octet of IOM channel 2 of the IOM allows the access of external communication controllers (up to 7) to the layer-1 functions provided in the ISAC-S TE and to the D channel. (TIC bus; see figure 17). To this effect the outputs of the controllers (ICC:ISDN Communication Controller PEB 2070) are wired-or-and connected to pin IDP1. The inputs of the ICCs are connected to pin IDP0. External pull-up resistors on IDP0/1 are required. The arbitration mechanism must be activated by setting MODE:DIM2-0=001 (see chapter 4.1.7). An access request to the TIC bus may either be generated by software (P access to the C/I Semiconductor Group 41 Functional Description channel) or by the ISAC-S TE itself (transmission of an HDLC frame). A software access request to the bus is effected by setting the BAC bit (CIX0 register) to "1". In the case of an access request, the ISAC-S TE checks the Bus Accessed-bit (bit 5 of IDP1 last octet of CH2, see figure 18) for the status "bus free", which is indicated by a logical "1". If the bus is free, the ISAC-S TE transmits its individual TIC-bus address programmed in the STCR register. The TIC bus is occupied by the device which sends its address error-free. If more than one device attempt to seize the bus simultaneously, the one with the lowest address values wins. MR MX B1 B2 MON0 D CI0 IC1 MR MX IC2 MON1 CI1 BAC TAD 2 1 TAD BAC ITD02575 0 TIC-Bus Address (TAD 2-0) Bus Accessed ('1' no TIC-Bus Access) Figure 18 Structure of Last Octet of CH2 on IDP1 (DU) When the TIC bus is seized by the ISAC-S TE, the bus is identified to other devices as occupied via the IDP1 C/I Bus Accessed-bit state "0" until the access request is withdrawn. After a successful bus access, the ISAC-S TE is automatically set into a lower priority class, that is, a new bus access cannot be performed until the status "bus free" is indicated in two successive frames. If none of the devices connected to the IOM interface request access to the D- and C/I channels, the TIC-bus address 7 will be present. The device with this address will therefore have access, by default, to the D and C/I channels. Note: Bit BAC (CIX0 register) should be reset by the P when access to the C/I channels is no more requested, to grant other devices access to the D- and C/I channels. The availability of the S/T interface D channel is indicated in bit 5 "Stop/Go" (S/G) of the IDP0 last octet of C/I channel (figure 19). S/G = 1 : stop S/G = 0 : go Semiconductor Group 42 Functional Description MR MX B1 B2 MON0 D CI0 IC1 MR MX IC2 MON1 S/G A/B CI1 S/G A/B STOP/GO Available/Blocked ITD05422 Figure 19 Structure of Last Octet of CH2 on IDP0 (DD) The stop/go bit is available to other layer-2 devices connected to the IOM to determine if they can access the S/T bus D channel. The available busy bit is not influenced by the ISAC-S TE. Semiconductor Group 43 Functional Description 2.4 Layer-1 Functions for the S/T Interface - line transceiver functions for the S/T interface according to the electrical specifications of CCITT I.430; - conversion of the frame structure between IOM and S/T interface; - conversion from/to binary to/from pseudo-ternary code; - level detect; - S/T-timing generation using IOM timing synchronous to system, or vice versa; - D-channel access control and priority handling; - activation/deactivation procedures, triggered by primitives received over the IOM C/I channel or by INFO's received from the line; - frame alignment; - execution of test loops. For a block diagram, see figure 8. The wiring configurations in user premises, in which the ISAC-S TE can be used are illustrated in figure 20. Semiconductor Group 44 Functional Description <_ 1.5 km 1) R ISAC -S TE TR TR R ISAC -S LT-S TE <_ 1.5 km 1) R IOM -2 R ISAC -S TR TR Point-to-Point Configurations SBC NT LT-T 1) R The maximum line attenuation toleratet by the ISAC -S 15 dB at 96 kHz. R ISAC -S LT-S <_ 150 m R IOM -2 TR TR Short Passive Bus SBC <_ 10 m R ISAC -S TE TE1 NT R ISAC -S TE TE8 R ISAC -S <_ 150 m LT-S <_ 35 m R IOM -2 TR TR <_ 10 m Extended Passive Bus SBC NT TR:Terminating Resistor R ISAC -S TE TE1 ITS05423 R ISAC -S TE TE8 Figure 20 Wiring Configurations in User Premises Semiconductor Group 45 Functional Description 2.4.1 S/T Interface According to CCITT recommendation I.430 pseudo-ternary encoding with 100% pulse width is used on the S/T interface. A logical "1" corresponds to a neutral level (no current), whereas logical "0" 's are encoded as alternating positive and negative pulses. An example is shown in figure 21. 0 1 0 0 1 1 0 0 0 1 1 +V 0V -V ITD00322 Figure 21 S/T-Interface Line Code One frame consists of 48 bits, at a nominal bit rate of 192 kbit/s. Thus each frame carries two octets of B1, two octets of B2, and four D bits, according to the B1+B2+D structure defined for the ISDN-basic access (total useful data rate: 144 kbit/s). Frame begin is marked using a code violation (no mark inversion). The frame structures (from network to subscriber, and subscriber to network) are shown in figure 22. 48 Bits in 250 s DL. F L. NT B1 E D A FA N B2 E DM B1 EDS B2 E D L. F L. 0 TE 1 0 2 Bits Offset D L. F L. TE NT 0 1 0 B1 L. D L. FA L. B2 L. D L. B1 L. D L. B2 L. D L. F L. t F = Framing Bit L = DC Balancing Bit D = D-Channel Bit E = D-Echo-Channel Bit FA = Auxiliary Framing Bit or Q-Bit N = Bit set to a Binary Value N = FA B1 = Bit within B Channel 1 B2 = Bit within B Channel 2 A = Bit used for Activation S = Subchannel SC1 through SC5 bit position M = Multiframing Bit Figure 22 Frame Structure at Reference Points S and T (CCITT I.430) Note: Dots demarcate those parts of the frame that are independently DC-balanced. Semiconductor Group 46 ITD02330 Functional Description 2.4.2 Analog Functions For both receive and transmit direction, a 2:1 transformer is used to connect the ISAC-S TE transceiver to the 4 wire S/T interface. The corrections are shown in figure 23. +5V 2:1 SX1 VDD Transmit Pair ISAC-S TE SX2 10 F PSB 2086 2186 PEB VSSD 2:1 SR1 Receive Pair VSSA SR2 GND ITS05640 Figure 23 ISAC-S TE External S-Interface Circuitry The full-bauded pseudo-ternary pulse shaping is achieved with the integrated transmitter which is realized as a current limited voltage source. A voltage of 2.1 V is delivered between SX1-SX2, which yields a current of 7.5 mA over 280 . The receiver is designed as a threshold detector with adaptively switched threshold levels. Pin SR1 delivers 2.5 V as an output, which is the virtual ground of the input signal on pin SR2. The external transformer of ratio 2:1 is needed in both receive and transmit direction to provide for isolation and transform voltage levels according to CCITT recommendations. The equivalent circuits of the integrated receiver and transmitter are shown in figure 24. R R ISAC -S TE PSB 2186 ISAC -S TE PSB 2186 50 k 40 k SX1 2.1 V SR1 - 3/4 13.4 mA + 40 k 50 k SR2 SX2 2.1 V 2.5 V ITS05940 ITS05939 switch position shown for negative pulses Figure 24 Equivalent Internal Circuits of Receiver and Transmitter Stages Semiconductor Group 47 Functional Description Symmetrical S-Bus Receiver The S-bus receiver of the PSB 2186 is a symmetrical one. This results in a simplification of the external circuitry and PCB layout to meet the I.430 receiver input impedance specification. 2.4.3 S/T-Interface Circuitry In order to comply to the physical requirements of CCITT recommendation I.430 and considering the national requirements concerning overvoltage protection and electromagnetic compatibility (EMC), the ISAC-S TE needs some additional circuitry. Useful hints how to design such interface circuitry are contained on the Application Note "S/Tinterface circuitry using the PEB 2080 SBC or PEB 2085 ISAC-S (12/89)". The transmitter of the PSB 2186 ISAC-S TE is identical to that of both the PEB 2080 SBC and PEB 2085/ISAC-S, hence, the line interface circuitry should be the same (figure 25). The external resistors (20 ... 40 ) are required in order to adjust the output voltage to the pulse mask (nominal 750 mV according to CCITT I.430, to be tested with the command "SSZ") on the one hand and in order to meet the output impedance of minimum 20 (transmission of a binary zero according to CCITT I.430, to be tested with the command "SCZ") on the other hand. 20...40 2:1 SX1 2.7 V R ISAC -S TE PSB 2186 GND Overvoltage Protection VDD S-Bus Connector 20...40 SX2 DC Point ITS04475 Figure 25 External Transmitter Circuitry The receiver of the PSB 2186 ISAC-S TE is symmetrical as opposed to both PEB 2080 SBC and PEB 2085 ISAC-S. Thus two resistors of 10 k must be placed in series to the receiver inputs. In order to protect the ISAC-S inputs and comply to impedance requirements performed without power supply (96-kHz test), the 10 k tester is split-up. A 1.8 k resistor protects the device inputs, while the 8.2 k resistors limit the maximum current in impedance tests. Semiconductor Group 48 Functional Description 8.2 k 1.8 k 2:1 SR1 47 pF R ISAC -S TE PSB 2186 Overvoltage Protection VDD GND 1.8 k S-Interface Connector 8.2 k SR2 47 pF DC Point ITS04474 Figure 26 External Receiver Circuitry 2.4.4 S/T Interface Pre-Filter Compensation To compensate for the extra delay introduced into the received signal by a filter, the sampling of the receive signal can be delayed by programming bits TEM and PFS in the ADF1 register as shown in table 3. Note that setting TEM to "1" and PFS to "0" has the effect of completely disabling layer-1 functions, for test purposes (see section 2.6). Table 3 TEM/PFS Function Table TEM PFS Effect 0 0 No pre-filter (0 delay) 0 1 Pre-filter delay compensation 520 ns 1 1 Pre-filter delay compensation 910 ns 1 0 Test mode (layer-1 disabled) This delay compensation might be necessary in order to comply with the "total phase deviation input to output" requirement of CCITT recommendation I.430 which specifies a phase deviation in the range of - 7% to + 15% of a bit period. Semiconductor Group 49 Functional Description 2.4.5 Receiver Functions 2.4.5.1 Receive Signal Oversampling In order to additionally reduce the bit error rate in severe conditions, the ISAC-S TE performs oversampling of the received signal and uses majority decision logic. As illustrated in figure 27, each received bit is sampled 29 times at 7.68-MHz clock intervals inside the estimated bit window. The samples obtained are compared against a threshold VTR1 or VTR2 (see section: Adaptive Receiver Characteristics). If at least 16 samples have an amplitude exceeding the selected threshold, a logical "0" is considered to be detected, otherwise a logical "1" (no signal) is considered detected. VSR2 - VSR1 VTR1 or VTR2 0V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Derived 192-kHz Receive Bit Period ITD02361 Figure 27 S/T-Receive Signal Oversampling Semiconductor Group 50 Functional Description 2.4.5.2 Adaptive Receiver Characteristics The integrated receiver uses an adaptively switched threshold detector. The detector controls the switching of the receiver between two sensitivity levels. The hysteresis characteristics of the receiver are shown in figure 28. V SR2 - V SR1 V SR2 - V SR1 Logical 0 Logical 0 + 375 mV Logical 1 0V Logical 0 - 375 mV + 225 mV 0V Logical 1 - 225 mV Logical 0 State 1 High Sensitivity with V TR1 = 225 mV State 2 Low Sensitivity with V TR2 = 375 mV V max > 1 V or V max < -1 V in two Consecutive Frames 1 750 mV <_ V max <_ 1 V 2 V max < 750 mV and V max > -750 mV V SR2 - V SR1 = Input Voltage V TR1 V TR2 = Threshold Voltages of the Receiver Threshold Detector V max = Maximum Value of V SR2 - V SR1 during one Frame 750 mV <_ V max <_ 1 V ITD00774 Figure 28 Switching of the Receiver between High Sensitivity and Low Sensitivity Semiconductor Group 51 Functional Description 2.4.5.3 Level Detection Power Down In power down state, (see chapter 3.3.1) only an analog level detector is active. All clocks, including the IOM interface, are stopped. The data lines are "high", whereas the clocks are "low". An activation initiated from the exchange side (Info 2 on S bus detected) will have the consequence that a clock signal is provided automatically. From the terminal side an activation must be started by setting and resetting the SPU bit in the SPCR register (see chapter 4). 2.4.6 Timing Recovery The transmit and receive bit clocks are derived, with the help of the DPLL, from the S-interface receive data stream. The received signal is sampled several times inside the derived receive clock period, and a majority logic is used to additionally reduce bit error rate in severe conditions (see chapter 2.4.5). The transmit frame is shifted by two bits with respect to the received frame. The output clocks (DCL, FSC1 etc.) are synchronous to the S-interface timing. TE Mode BCL DCL PLL FSC ITS05425 Figure 29 Clock System of the ISAC(R)-S TE in TE Mode Semiconductor Group 52 Functional Description 2.4.7 Activation/Deactivation An incorporated finite state machine controls ISDN layer-1 activation/deactivation according to CCITT (see chapter 3.4). Loss of Synchronization / Resynchronization The following section describes the behaviour of the PSB 2186 in respect to the CTS test procedures for frame alignment. Setting of the ISAC-S TE The ISAC-S TE needs to be programmed for multiframe operation with the Q-bits set to '1'. STAR2: MULT = 0 SQXR:SQX1-4 = 1111B (xFH) 2.4.7.1 FAinfA_1fr This test checks if no loss of frame alignment occurs upon a receipt of one bad frame. The pattern for the bad frame is defined as IX_96 kHz. This pattern was revised so that a code violation is generated at the begin of the next info 4 frame. Code Violation Info 4 Info 4 Info 4 IX_96 kHz Info 3 Info 3 Info 3 Info 3 ITD05898 Device Settings Result PSB 2186 V1.1 none Pass Semiconductor Group 53 Comments Functional Description 2.4.7.2 FAinfB_1fr This test uses a frame which has no framing and balancing bit. Code Violation Info 4 Info 4 Info 4 I4_BASIC IX_I4noflag Info 3 Info 3 Info 3 Info 3 ITD05899 Device Settings Result PSB 2186 V1.1 none Pass 2.4.7.3 Comments FAinfD_1fr This test uses a frame which remains at binary '1' until the first code violation in bit 16. Since it is specified, that a terminal should mirror the received FA-bit in the transmitted FA-bit, a frame is generated by the IUT which will not generate a second code violation. The pattern for a correct i3_BASIC frame states that the FA-bit may have any value. Info 4 Info 4 Info 4 FA = 1 Info 3 Info 3 Info 3 Info 3 with FA = 1 Device Settings Result PSB 2186 V1.1 none Pass Semiconductor Group 54 ITD05900 Comments Functional Description 2.4.7.4 FAinfA_kfr This test uses a number of IX_96 kHz frames to check the loss of synchronization. Info 4 Info 4 IX_96 kHz Info 3 Info 3 IX_96 kHz IX_96 kHz Info 3 I3_SFAL Info 0 ITD05901 Device Settings Result PSB 2186 V1.1 n=2 Pass 2.4.7.5 Comments FAinfB_kfr This test uses a number of IX_I4noflag frames to check the loss of synchronization. Info 4 Info 4 I4_BASIC IX_I4noflag Info 3 Info 3 Info 3 IX_I4noflag I3_SFAL IX_I4noflag Info 0 ITD05902 Device Settings Result PSB 2186 V1.1 n=2 Pass Semiconductor Group 55 Comments Functional Description 2.4.7.6 FAinfD_kfr This test uses a number of IX_I4voil16 frames to check the loss of synchronization. The first Info 3 frame with the FA-bit set to one looks like a i3_SFAL frame but it is a correct info 3 frame since the receiver stays synchronous (see FAinfD_1fr). Info 4 Info 4 Info 3 FA = 1 FA = 1 Info 3 with FA = 1 I3_SFAL Info 3 ITD05903 Device Settings Result PSB 2186 V1.1 n=2 Pass 2.4.7.7 Comments FAregain This test uses I4_BASIC frames to regain the frame alignment. The protocol tester evaluates the difference between sending the first info 4 frame until a complete info 3 frame has been received. This period is considered as 'm+1'. 'm' must be specified before the test is started. The PSB 2186 achieves synchronization after 5 or 6 frames. The actual value depends on internal timing conditions which can not be influenced from extern. This is a result of changes that were made to handle the iXvoil16 test case correctly. The info 4 pattern generates the second code violation at the position of the F A-bit. Around that bit position, the state machine changes its states. As a result of that overlap, the info 3 frame is transmitted after 5 frames or one frame later. Info X 1 2 3 4 5 6 7 Info 4 Info 4 Info 4 Info 4 Info 4 Info 4 Info 4 Info 3 Info 3 ITD05904 Device Settings Result PSB 2186 V1.1 m = 5 or 6 Pass Semiconductor Group 56 Comments Functional Description 2.4.8 D-Channel Access The D channel is submitted to the D-channel access procedure according to CCITT recommendation I.430. The D-channel access procedure according to CCITT I.430 including priority management is fully implemented in the ISAC-S: If collision detection is programmed (MODE:DIM2-0), a collision is detected if either an echo bit of "0" is recognized and a D bit of "1" was generated, or an echo bit of "1" is recognized and a D bit of "0" was generated. When this occurs, D-channel transmission is immediately stopped, and the echo channel is monitored to enable a subsequent D-channel access to be attempted. Stop/Go Bit As the collision resolution is performed by the layer-1 part of the device, an information about the D-channel status ("ready" or "busy") must be sent back to the layer-2 part to control HDLC transmission. For this goal a Stop/Go (S/G) bit is transmitted over the IOM interface to the layer-2 device. The S/G bit is transmitted in bit 90 of an IOM-2 frame (12-byte structure) (see figure 19). A logical "1" of the S/G bit indicates a collision on the S bus. By sending the S/G bit a logical "0" to the layer-2 controller in anticipation of the S bus D channel "ready"-state, the first valid 0 bits will emerge from the layer-1 part at exactly that moment an access is becoming possible. Selection of D-Channel Access Mode For proper operation of the D-channel access procedure, the ISAC-S TE must be programmed via the MODE (see chapter 4.1.7) register to evaluate the stop/go bit. This is achieved by setting MODE:DIM2-0 to 001 or 011. Selection of the Priority Class The priority class (priority 8 or priority 10) is selected by transferring the appropriate activation command via the Command/Indicate (C/I) channel of the IOM interface to the layer-1 controller. If the activation of the S interface is initiated by a TE, the priority class is selected implicitly by the choice of the activation command. If the S-Interface is activated from the NT, an activation command selecting the desired priority class should be programmed at the TE on reception of the activation indication (AI8). In the activated state, the priority class may be changed whenever required simply by programming the respective activation request command (AR8 or AR10). The following table summarizes the C/I codes used for setting the priority classes: Semiconductor Group 57 Functional Description Table 4 Priority Commands/Indications Command (upstream) Abbr. Code Remarks Activate request, set priority 8 AR8 1000 Activate request, set priority 10 AR10 1001 Activation command: Set D-channel priority to 8 Activation command: Set D-channel priority to 10 Indication (downstream) Abbr. Code Remarks Activate indication with priority class 8 Activate indication with priority class 10 AI8 1100 AI10 1101 Info 4 received: D-channel priority is 8 or 9 Info 4 received: D-channel priority is 10 or 11 2.4.9 S- and Q-Channel Access Access to the received/transmitted S- or Q channel is provided via registers. As specified by CCITT I.430, the Q bit is transmitted from TE to NT in the position normally occupied by the auxiliary framing bit (FA) in one frame out of 5, whereas the S bit is transmitted from NT to TE in a spare bit, see figure 22. The functions provided by the ISAC-S are: - Synchronization to the received 20 frame multiframe by means of the received M bit pattern. Synchronism is achieved when the M bit has been correctly received during 20 consecutive frames starting from frame number 1 (table 5). - When synchronism is achieved, the four received S bits in frames 1, 6, 11 and 16 are stored as SQR1 to SQR4 in the SQRR register if the complete M bit multiframe pattern was correctly received in the corresponding multiframe. A change in any of the received four bits (SQR1, 2, 3 or 4) is indicated by an interrupt (CISQ in ISTA and SQC in CIR0). - When an M bit is observed to have a value different from that expected, the synchronism is considered lost. The SQR bits are not updated until synchronism is regained. The synchronization state is constantly indicated by the SYN bit in the SQRR register. - When synchronism with the received multiframe is achieved, the four bits SQX1 to SQX4 stored in the SQXR register are transmitted as the four Q bits (FA-bit position) in frames 1, 6, 11 and 16 respectively (starting from frame number one). Otherwise the bit transmitted is a mirror of the received FA-bit. At loss of synchronism (mismatch in M bit) the mirroring is resumed starting with the next FA-bit. - The S/T multiframe synchronization can be disabled in the STAR2 register (MULT bit). Semiconductor Group 58 Functional Description Table 5 S- and Q-Bit Position Identification and Multiframe Structure S- and Q-Channel Structure Frame Number NT-to-TE FA-Bit Position NT-to-TE M Bit NT-to-TE S Bit TE-to-NT FA-Bit Position 1 2 3 4 5 ONE ZERO ZERO ZERO ZERO ONE ZERO ZERO ZERO ZERO S1 ZERO ZERO ZERO ZERO Q1 ZERO ZERO ZERO ZERO 6 7 8 9 10 ONE ZERO ZERO ZERO ZERO ZERO ZERO ZERO ZERO ZERO S2 ZERO ZERO ZERO ZERO Q2 ZERO ZERO ZERO ZERO 11 12 13 14 15 ONE ZERO ZERO ZERO ZERO ZERO ZERO ZERO ZERO ZERO S3 ZERO ZERO ZERO ZERO Q3 ZERO ZERO ZERO ZERO 16 17 18 19 20 ONE ZERO ZERO ZERO ZERO ZERO ZERO ZERO ZERO ZERO S4 ZERO ZERO ZERO ZERO Q4 ZERO ZERO ZERO ZERO 1 2 etc. ONE ZERO ONE ZERO S1 ZERO Q1 ZERO Semiconductor Group 59 Functional Description 2.5 Terminal Specific Functions Watchdog and External Awake In addition to the ISAC-S TE standard functions supporting the ISDN-basic access, the ISAC-S TE contains optional functions, useful in various terminal configurations. The terminal specific functions are enabled by setting bit TSF (STCR register) to "1". This has two effects: The EAW line is defined as an external awake input; Second, the interrupts SAW and WOV (EXIR register) are enabled: SAW (Subscriber Awake) generated by a falling edge on the EAW line WOV (Watchdog timer OVerflow) generated by the watchdog timer. This occurs when the processor fails to write two consecutive bit patterns in ADF1: ADF1 WTC1 WTC2 Watchdog Timer Control 1, 0. The WTC1 and WTC2 bits have to be successively written in the following manner within 128 ms: 1. 2. WTC1 WTC2 1 0 0 1 As a result the watchdog timer is reset and restarted. Otherwise a WOV is generated. Deactivating the terminal specific functions is only possible with a hardware reset. Having enabled the terminal specific functions via TSF=1, the user can make the ISAC-S TE generate a reset signal by programming the Reset Source Select RSS bit (CIXR/CIX0 register), as follows: 0 A reset signal is generated as a result of - a falling edge on the EAW line (subscriber awake) - a C/I code change (exchange awake) A falling edge on the EAW line also forces the IDP1 line of the IOM interface to zero. The consequence of this is that the IOM interface and the ISAC-S TE leaves the power-down state. A corresponding interrupt status (CISQ or SAW) is also generated. 1 A reset signal is generated as a result of the expiration of the watchdog timer (indicated by the WOV interrupt status). Note that the watchdog timer is not running when the ISAC-S TE is in the power-down state (IOM not clocked). Note: Bit RSS has a significance only if terminal specific functions are activated (TSF=1). Semiconductor Group 60 Functional Description The RSS bit should be set to "1" by the user when the ISAC-S TE is in power-up to prevent an edge on the EAW line or a change in the C/I code from generating a reset pulse. Switching RSS from 0 to 1 or from 1 to 0 resets the watchdog timer. The reset pulse generated by the ISAC-S TE (output via RST pin) has a pulse width of: - 125 s when generated by the watchdog timer - 16 ms when generated by EAW line or C/I-code change. Semiconductor Group 61 Functional Description 2.6 Test Functions The ISAC-S TE provides several test and diagnostic functions which can be grouped as follows: digital loop via TLP (Test Loop, SPCR register) command bit: IDP1 is internally connected with IDP0, output from layer 1 (S/T) on IDP0 is ignored; this is used for testing ISAC-S TE functionality excluding layer 1; test of layer-2 functions while disabling all layer-1 functions and pins associated with them (including clocking, in TE mode), via bit TEM (Test Mode in ADF1 register); the ISAC-S TE is then fully compatible to the ICC (PEB 2070) seen at the IOM interface. loop at the analog end of the S interface; Test loop 3 is activated with the C/I-channel command Activate Request Loop (ARL). An S interface is not required since INFO3 is looped back to the receiver. When the receiver has synchronized itself to this signal, the message "Test Indication" (or "Awake Test Indication") is delivered in the C/I channel. No signal is transmitted over the S interface. In the test loop mode the S-Interface awake detector is enabled i.e. if a level is detected (e.g. Info 2/Info 4) this will be reported by the Awake Test Indication (ATI). The loop function is not effected by this condition and the internally generated 192-kHz line clock does not depend on the signal received at the S interface. Semiconductor Group 62 Functional Description 2.7 Layer-2 Functions for the ISDN-Basic Access LAPD, layer 2 of the D-channel protocol (CCITT I.441) includes functions for: - Provision of one or more data link connections on a D channel (multiple LAP). Discrimination between the data link connections is performed by means of a data link connection identifier (DLCI = SAPI + TEI) - HDLC framing - Application of a balanced class of procedure in point-multipoint configuration. The simplified block diagram in figure 30 shows the functional blocks of the ISAC-S TE which support the LAPD protocol. Layer 1 IOM HDLC Receiver HDLC Transmitter R Layer-1 Functions LAPD Controller S(D-Channel) Status Command Registers Layer 2 R-FIFO 2 x 32 byte X-FIFO 2 x 32 byte FIFO Controller P-Interface Upper Layers C-System ITS00861 Figure 30 D-Channel Processing of the ISAC(R)-S TE For the support of LAPD the ISAC-S TE contains an HDLC transceiver which is responsible for flag generation/recognition, bit stuffing mechanism, CRC check and address recognition. A powerful FIFO structure with two 64-byte pools for transmit and receive directions and an intelligent FIFO controller permit flexible transfer of protocol data units to and from the C system. Semiconductor Group 63 Functional Description 2.7.1 Message Transfer Modes The HDLC controller can be programmed to operate in various modes, which are different in the treatment of the HDLC frame in the receive direction. Thus, the receive data flow and the address recognition features can be programmed in a flexible way, which satisfies different system requirements. In the auto mode the ISAC-S TE handles elements of procedure of the LAPD (S and I frames) according to CCITT I.441 fully autonomously. For the address recognition the ISAC-S TE contains four programmable registers for individual SAPI and TEI values SAP1-2 and TEI1-2, plus two fixed values for "group" SAPI and TEI, SAPG and TEIG. There are 5 different operating modes which can be set via the MODE register (addr. 22 H): Auto-mode (MDS2, MDS1 = 00) Characteristics: - Full address recognition (1 or 2 bytes). - Normal (mod 8) or extended (mod 128) control field format - Automatic processing of numbered frames of an HDLC procedure (see 2.7.5) If a 2-byte address field is selected, the high address byte is compared with the fixed value FEH or FCH (group address) as well as with two individually programmable values in SAP1 and SAP2 registers. According to the ISDN LAPD protocol, bit 1 of the high byte address will be interpreted as command/response bit (C/R) dependent on the setting of the CRI bit in SAP1, and will be excluded from the address comparison. Similarly, the low address byte is compared with the fixed value FFH (group TEI) and two compare values programmed in special registers (TEI1, TEI2). A valid address will be recognized in case the high and low byte of the address field match one of the compare values. The ISAC-S TE can be called (addressed) with the following address combinations: - SAP1/TEI1 - SAP1/FFH - SAP2/TEI2 - SAP2/FFH - FEH (FCH)/TEI1 - FEH (FCH)/TEI2 - FEH (FCH)/FFH Only the logical connection identified through the address combination SAP1, TEI1 will be processed in the auto mode, all others are handled as in the non-auto mode. The logical connection handled in the auto-mode must have a window size 1 between transmitted and acknowledged frames. HDLC frames with address fields that do not match with any of the address combinations, are ignored by the ISAC-S TE. Semiconductor Group 64 Functional Description In case of a 1-byte address, TEI1 and TEI2 will be used as compare registers. According to the X.25 LAPB protocol, the value in TEI1 will be interpreted as command and the value in TEI2 as response. The control field is stored in the RHCR register and the I field in the RFIFO. Additional information is available in the RSTA. Non-auto mode (MDS2, MDS1 = 01) Characteristics:Full address recognition (1 or 2 bytes) Arbitrary window sizes All frames with valid addresses (address recognition identical to auto mode) are accepted and the bytes following the address are transferred to the P via RHCR and RFIFO. Additional information is available in the RSTA. Transparent mode 1 (MDS2, MDS1, MDS0 = 101) Characteristics: TEI recognition A comparison is performed only on the second byte after the opening flag, with TEI1, TEI2 and group TEI (FFH). In the case of a match, the first address byte is stored in SAPR, the (first byte of the) control field in RHCR, and the rest of the frame in the RFIFO. Additional information is available in the RSTA. Transparent mode 2 (MDS2, MDS1, MDS0 = 110) Characteristics: no address recognition Every received frame is stored in the RFIFO (first byte after opening flag to CRC field). Additional information can be read from the RSTA. Transparent mode 3 (MDS2, MDS1, MDS0 = 111) Characteristics: SAPI recognition A comparison is performed on the first byte after the opening flag with SAP1, SAP2 and group SAPI (FE/FCH). In the case of a match, all the following bytes are stored in RFIFO. Additional information can be read from the RSTA. Semiconductor Group 65 Functional Description 2.7.2 Protocol Operations (auto-mode) In addition to address recognition all S and I frames are processed in hardware in the automode. The following functions are performed: - update of transmit and receive counter - evaluation of transmit and receive counter - processing of S commands - flow control with RR/RNR - response generation - recognition of protocol errors - transmission of S commands, if an acknowledgement is not received - continuous status query of remote station after RNR has been received - programmable timer/repeater functions. The processing of frames in auto-mode is described in detail in chapter 2.7.5: Documentation of the Auto-Mode. Semiconductor Group 66 Functional Description 2.7.3 Reception of Frames A 2 x 32 byte FIFO buffer (receive pools) is provided in the receive direction. The control of the data transfer between the CPU and the ISAC-S TE is handled via interrupts. There are two different interrupt indications concerned with the reception of data: - RPF (Receive Pool Full) interrupt, indicating that a 32-byte block of data can be read from the RFIFO and the received message is not yet complete. - RME (Receive Message End) interrupt, indicating that the reception of one message is completed, i.e. either one message 32 bytes, or the last part of a message > 32 bytes is stored in the RFIFO. Depending on the message transfer mode the address and control fields of received frames are processed and stored in the Receive FIFO or in special registers as depicted in figure 32. The organization of the RFIFO is such that up to two short ( 32 bytes), successive messages, with all additional information can be stored. The contents of the RFIFO would be, for example, as shown in figure 31. RFIFO Interrupts in Wait Line 0 Receive Message 1 ( <_ 32 bytes) 31 0 RME Receive Message 2 ( <_ 32 bytes) RME 31 ITS01502 Figure 31 Contents of RFIFO (short message) Semiconductor Group 67 Functional Description Flag Auto-Mode (U-and -Frames) - Non-Auto Mode Transparent Mode 1 Address High Address Low Control Information CRC SAP1,SAP2 FE,FC TEI1,TEI2 FF RHCR RFIFO RSTA (Note 1) (Note 2) (Note 3) SAP1,SAP2 FE,FC TEI1,TEI2 FF RHCR RFIFO RSTA (Note 1) (Note 2) (Note 4) SAPR TEI1,TEI2 FF RHCR RFIFO RSTA Flag (Note 4) Transparent Mode 2 SAP1,SAP2 FE,FC Transparent Mode 3 RFIFO RSTA RFIFO RSTA Description of Symbols: ITD05674 R Checked automatically by ISAC -S TE Compared with Register or Fixed Value Stored Info Register or RFIFO Figure 32 Receive Data Flow Note 1Only if a 2-byte address field is defined (MDS0 = 1 in MODE register). Note 2Comparison with Group TEI (FFH) is only made if a 2-byte address field is defined (MDS0 = 1 in MODE register). Note 3In the case of an extended, modulo 128 control field format (MCS = 1 in SAP2 register) the control field is stored in the RHCR in compressed form (I frames). Note 4In the case of extended control field, only the first byte is stored in the RHCR, the second in the RFIFO. Semiconductor Group 68 Functional Description When 32 bytes of a message longer than that are stored in the RFIFO, the CPU is prompted to read out the data by an RPF interrupt. The CPU must handle this interrupt before more than 32 additional bytes are received, which would cause a "data overflow".This corresponds to a maximum CPU reaction time of 16 ms (data rate 16 kbit/s). After a remaining block of less than or equal to 16 bytes has been stored, it is possible to store the first 16 bytes of a new message (see figure 33). The internal memory is now full. The arrival of additional bytes will result in "data overflow" (RSTA:RDO) and a third new message in "frame overflow" (EXIR:RFO). The generated interrupts are inserted together with all additional information into a queue to be individually passed to the CPU. After an RPF or RME interrupt has been processed, i.e. the received data has been read from the RFIFO, this must be explicitly acknowledged by the CPU issuing an RMC (Receive Message Complete) command. The ISAC-S TE can then release the associated FIFO pool for new data. If there is an additional interrupt in the queue it will be generated after the RMC acknowledgement. RFIFO the Queue Interrupts in RFIFO 0 Interrupts in the Queue 0 Long Message 1 ( <_ 46 bytes) Long Message 31 0 RPF 31 0 RPF 15 16 RME Message 2 ( <_ 32 bytes) 31 31 RPF RME ITS01501 Figure 33 Contents of the RFIFO (long messages) Semiconductor Group 69 Functional Description Information about the received frame is available for the P when a RME interrupt is generated, as shown in table 6. Table 6 Receive Information at RME Interrupt Information Register (adr. Bit hex) Mode First byte after flag (SAPI of LAPD address field) SAPR (26) Transparent mode 1 Control field RHCR (29) - Auto-mode, I (modulo 8) and U frames Compressed control field RHCR (29) - Auto-mode, I frames (modulo 128) 2nd byte after flag RHCR (29) - Non-auto mode, 1-byte address field 3rd byte after flag RHCR (29) - Non-auto mode, 2-byte address field Transparent mode 1 Type of frame (Command/Response) RSTA (27) C/R Auto-mode, 2 byte address field Non-auto mode, 2-byte address field Transparent mode 3 Recognition of SAPI RSTA (27) SA1-0 Auto-mode, 2 byte address field Non-auto mode, 2-byte address field Transparent mode 3 Recognition of TEI RSTA (27) TA All except transparent modes 2, 3 Result of CRC check (correct/incorrect) RSTA (27) CRC ALL Data available in RFIFO (yes/no) RSTA (27) RDA ALL Abort condition detected (yes/no) RSTA (27) RAB ALL Data overflow during reception of a frame (yes/no) RSTA (27) RDO ALL Number of bytes received RBCL in RFIFO (25) RBC4-0 ALL Message length (25) RBC11-0 ALL (2A) OV Semiconductor Group RBCL RBCH - 70 Functional Description 2.7.4 Transmission of Frames A 2 x 32 byte FIFO buffer (transmit pools) is provided in the transmit direction. If the transmit pool is ready (which is true after an XPR interrupt or if the XFW bit in STAR is set), the CPU can write a data block of up to 32 bytes to the transmit FIFO. After this, data transmission can be initiated by command. Two different frames types can be transmitted: - Transparent frame (command: XTF), or - I frames (command: XIF) as shown in figure 34. For transparent frames, the whole frame including address and control field must be written to the XFIFO. HDLC Frame Flag Address Control Information CRC Flag Transmit I-Frame (XIF) Auto Mode,8 - Bit Addr. Flag XAD1 Control XFIFO CRC Flag Transmit I-Frame (XIF) Auto -Mode, 16 - Bit Addr. Flag XAD1 XAD2 Control XFIFO CRC Flag Transmit Transparent Frame (XTF) All Modes Flag CRC Flag XFIFO ITD05667 Note: Length of Control Field is b or 16 Bit Description of Symbols: R Generated automatically by ISAC -S TE Written initially by CPU (Info Register) R Loaded (repeatedly) by CPU upon ISAC -S TE request (XPR Interrupt) Figure 34 Transmitter Data Flow The transmission of I frames is possible only if the ISAC-S TE is operating in the auto-mode. The address and control field is autonomously generated by the ISAC-S TE and appended to the frame, only the data in the information field must be written to the XFIFO. Semiconductor Group 71 Functional Description If a 2-byte address field has been selected, the ISAC-S TE takes the contents of the XAD 1 register to build the high byte of the address field, and the contents of the XAD 2 register to build the low byte of the address field. Additionally the C/R bit (bit 1 of the high byte address, as defined by LAPD protocol) is set to "1" or "0" dependent on whether the frame is a command or a response. In the case of a 1 byte address, the ISAC-S TE takes either the XAD 1 or XAD 2 register to differentiate between command or response frame (as defined by X.25 LAPB). The control field is also generated by the ISAC-S TE including the receive and send sequence number and the poll/final (P/F) bit. For this purpose, the ISAC-S TE internally manages send and receive sequence number counters. In the auto-mode, S frames are sent autonomously by the ISAC-S TE. The transmission of U frames, however, must be done by the CPU. U frames must be sent as transparent frames (CMDR:XTF), i.e. address and control field must be defined by the CPU. Once the data transmission has been initiated by command (CMDR:XTF or XIF), the data transfer between CPU and the ISAC-S TE is controlled by interrupts. The ISAC-S TE repeatedly requests another data packet or block by means of an ISTA:XPR interrupt, every time no more than 32 bytes are stored in the XFIFO. The processor can then write further data to the XFIFO and enable the continuation of frame transmission by issuing an XIF/XTF command. If the data block which has been written last to the XFIFO completes the current frame, this must be indicated additionally by setting the XME (Transmit Message End) command bit. The ISAC-S TE then terminates the frame properly by appending the CRC and closing flag. If the CPU fails to respond to an XPR interrupt within the given reaction time, a data underrun condition occurs (XFIFO holds no further valid data). In this case, the ISAC-S TE automatically aborts the current frame by sending seven consecutive "ones" (ABORT sequence). The CPU is informed about this via an XDU (Transmit Data Underrun) interrupt. It is also possible to abort a message by software by issuing a CMDR:XRES (Transmitter RESet) command, which causes an XPR interrupt. After an end of message indication from the CPU (CMDR:XME command), the termination of the transmission operation is indicated differently, depending on the selected message transfer mode and the transmitted frame type. If the ISAC-S TE is operating in the auto mode, the window size (= number of outstanding unacknowledged frames) is limited to "1"; therefore an acknowledgement is expected for every I frame sent with an XIF command. The acknowledgement may be provided either by a received S or I frame with corresponding receive sequence number. If no acknowledgement is received within a certain time (programmable), the ISAC-S TE requests an acknowledgement by sending an S frame with the poll bit set (P = 1) (RR or RNR). If no response is received again, this process is repeated in total N2 times (retry count, programmable via TIMR register). Semiconductor Group 72 Functional Description The termination of the transmission operation may be indicated either with: - XPR interrupt, if a positive acknowledgement has been received, - XMR interrupt, if a negative acknowledgement has been received, i.e. the transmitted message must be repeated (XMR = Transmit Message Repeat), - TIN interrupt, if no acknowledgement has been received at all after N2 times the expiration of the time period t1 (TIN = Timer INterrupt, XPR interrupt is issued additionally). Note: Prerequisite for sending I frames in the auto-mode (XIF) is that the internal operational mode of the timer has been selected in the MODE register (TMD bit = 1). The transparent transmission of frames (XTF command) is possible in all message transfer modes. The successful termination of a transparent transmission is indicated by an XPR interrupt. In all cases, collisions which occur on the S-Bus (D channel) before the first XFIFO pool has been completely transmitted and released are treated without P interaction. The ISAC-S TE will retransmit the frame automatically. If a collision is detected after the first pool has been released, the ISAC-S TE aborts the frame and requests the processor to repeat the frame with an XMR interrupt. Semiconductor Group 73 Functional Description 2.7.5 Documentation of the Auto Mode The auto mode of the ICC and ISAC-S TE is only applicable for the states 7 and 8 of the LAPD protocol. All other states (1 to 6) have to be performed in Non-Auto Mode (NAM). Therefore this documentation gives an overview of how the device reacts in the states 7 and 8, which reactions require software programming and which are done by the hardware itself, when interrupts and status register contents are set or change. The necessary software actions are also detailed in terms of command or mode register access. The description is based on the SDL diagrams of the ETSI TS 46-20 dated 1989. The diagrams are only annotated by documentary signs or texts (mostly register descriptions) and can therefore easily be interpreted by anyone familiar with the SDL description of LAPD. All deviations that occur are specially marked and the impossible actions, paths etc. are crossed out. To get acquainted with this documentation, first read through the legend-description and the additional general considerations, then start with the diagrams, referring to the legend and the register description in the Technical Manual if necessary. We hope you will profit from this documentation and use our software-saving auto-mode. 2.7.5.1 Legend of the Auto-Mode Documentation a.Symbols within a path There are 3 symbols within a path a.1. In the auto-mode the device processes all subsequent state transitions branchings etc. up to the next symbol. a.2. In the auto-mode the device does not process the state transitions, branchings etc. Within the path appropriate directions are given with which the software can accomplish the required action. a.3. A path cannot be implemented and no software or hardware action can change this. These paths are either optional or only applicable for window-size > 1. Semiconductor Group 74 Functional Description b.Symbols at a path There is 1 symbol at a path b.1. marks the beginning of a path, for which a.3 applies. c.Symbols at an internal or external message box. There are 2 symbols at a message box. c.1. This symbol means, that the action described in the box is not possible. Either the action specified is not done at all or an additional action is taken (written into the box). Box Note: The impossibility to perform the optional T203 timer-procedure is not explicitly mentioned; the corresponding actions are only crossed out. c.2. This symbol means, that within a software-path, by taking the prescribed register actions the contents of the box will be done automatically. Box d.Text within boxes Text within boxes can be grouped in one of two classes. d.1. Text Box or Box Text The text denotes an interrupt which is always associated with the event. (But can also be associated with other events). (See ISTA- and EXIR-register description in the Technical Manual for an interrupt description). d.2.The text describes a register access Box Text either a register read access to discriminate this state from others or to reach a branching condition or a register write access to give a command. The text is placed in the box that describes the functions for which the register access is needed. Semiconductor Group 75 Functional Description e.Text attached at the side of boxes e.1. Text Box e.2. The text describes an interrupt associated with the contents of the box. The interrupt is always associated with the box contents, if the interrupt name is not followed by a "/", it is associated only under appropriate conditions if a "/" is behind it. The text describes a possible or mandatory change of a bit in a statusregister associated with the contents of the box. Box Text (The attached texts can also be placed on the left side.) f.Text above and below boxes f.1. Text Box f.2. Box Text Text describes a mandatory action to be performed on the contents of the box. Text describes a mandatory action to be taken as a result of the contents of the box. Action here means register access. g.Shade boxes The box describes an impossible state or action for the device. Box Semiconductor Group 76 Functional Description 2.7.5.2 Additional General Considerations when Using the Auto Mode a)Switching from auto-mode to non-auto mode. As mentioned in the introduction the auto mode is only applicable in the states 7 and 8 of the LAPD. Therefore whenever these states have to be left (which is indicated by a "Mode:NAM" text) there are several actions to be taken that could not all be detailed in the SDL diagrams: a.1)write non-auto mode and TMD = 0 into the mode register. a.2)write the timer register with an arbitrary value to stop it. The timer T200 as specified in the LAPD protocol is implemented in the hardware only in the states 7 and 8; in all other states this or any other timer-procedure has to be done by the software with the possible use of the timer in external timer mode. a.3)read the WFA bit of the STAR2 register and store it in a software variable. The information in this bit may be necessary for later decisions. When switching from auto mode to non-auto mode XPR interrupts may be lost. a.4)In the non-auto mode the software has to decode I-, U- and S frames because I and S frames are only handled autonomously in the auto-mode. a.5)The RSC and PCE interrupts, the contents of the STAR2 register and the RRNR bit in the STAR register are only meaningful within the auto-mode. a.6)leave some time before RHR or XRES is written to reset the counters, as a currently sent frame may not be finished yet. b)What has to be written to the XFIFO? In the legend description when the software has to write contents of a frame to the XFIFO only "XFIFO" is shown in the corresponding box. We shall give here a general rule of what has to be written to the XFIFO: a) For sending an I frame with CMDR:XIF, only the information field content, i.e. no SAPI, TEI, Control field should be written to the XFIFO. b) For sending a U frame or any other frame with CMDR:XTF, the SAPI, TEI and the control field has to be written to the XFIFO. c)The interrupts XPR and XMR. The occurence of an XPR interrupt in auto-mode after an XIF command indicates that the I frame sent was acknowledged and the next I frame can be sent, if STAR2:TREC indicates state 7 and STAR:RRNR indicates Peer Rec not busy. If Peer Rec is busy after an XPR, the software should wait for the next RSC interrupt before sending the next I frame. If the XPR happens to be in the timer recovery state, the software has to poll the STAR2 register until the state multiple frame established is reached or a TIN interrupt is issued which requires auto mode to be left (One of these two conditions will occur before the time T200 x N200). In nonauto mode or after an XTF command the XPR just indicates, that the frame was sent successfully. Semiconductor Group 77 Functional Description The occurence of an XMR interrupt in auto-mode after an XIF command indicates that the I frame sent was either rejected by the Peer Entity or that a collision occured on the S interface. In both cases the I frame has to be retransmitted (after an eventual waiting for the RSC interrupt if the Peer Rec was busy; after an XMR the device will always be in the state 7). In non-auto mode or after an XTF command the XMR indicates that a collision occured on the S interface and the frame has to be retransmitted. d)The resetting of the RC variable: The RC variable is reset in the ICC and ISAC-S TE when leaving the state timer recovery. The SDL diagrams indicate a reset in the state multiple frame established when T200 expires. There is no difference to the outside world between these implementations however our implementation is clearer. e)The timer T203 procedure: We do not fully support the optional timer T203 procedure, but we can still find out whether or not S frames are sent on the link in the auto-mode. By polling the STAR2:SDET bit and (re)starting a software timer whenever a one is read we can build a quasi T203 procedure which handles approximately the same task. When T203 expires one is supposed to go into the timer recovery state with RC = 0. This is possible for the ICC and ISAC-S TE by just writing the STI bit in the CMDR register (auto-mode and internal timer mode assumed). f)The congestion procedure as defined in the 1 TR 6 of the "Deutsche Bundespost": In the 1 TR 6 a variable N2 x 4 is defined for the maximum number of Peer Busy requests. The 1 TR 6 is in this respect not compatible with the Q921 of CCITT or the ETSI 46-20 but it is, nevertheless, sensible to avoid getting into a hangup situation. With the ICC and ISAC-S TE this procedure can be implemented: After receiving an RSC interrupt with RRNR set one starts a software-timer. The timer is reset and stopped if one either receives another RSC interrupt with a reset RRNR, if one receives a TIN interrupt or if other conditions occur that result in a reestablishment of the link. The timer expires after N2 x 4 x T200 and in this case the 1 TR 6 recommends a reestablishment of the link. 2.7.5.3 Dealing With Error Conditions in Auto Mode In the Recommendation Q.921 of CCITT (Blue Book) several error conditions are described. We shall deal with them as far as they touch the auto mode of the ISAC-S (which only applies for states 7,8 of Q.921). Throughout the following document in subsections 1 we shall give the original Q.921-Text. For better discrimination against comments the original text is printed in italic characters. Please note that Q.921/table 5 has been corrected according to Corrigendum No. 1 10/1989. Subsections 2 document how the ISAC-S react in all cases, and subsections 3 will give hints how your software should respond to these reactions. Invalid Frames and Frame Abortion During data transmission invalid frames and frame abortion generally lead to error conditions. Semiconductor Group 78 Functional Description Q921: Invalid Frames and Frame Abortion Paragraphs 2.9 and 2.10 of the Q.921 deal with Invalid Frames and Frame Abortion. In the following the original text is given. Q.921 2.9: Invalid Frames An invalid frame is a frame which: a) is not properly bounded by two flags, or b) has fewer than 6 octets between flags or frames that contain sequence numbers, or c) does not consist of an integral number of octets prior to zero bit insertion or following zero bit extraction, or d) contains a frame check sequence error, or e) contains a single octet address field, or f) contains a service access point identifier (see 3.3.3) which is not supported by the receiver. Invalid frames shall be discarded without notification to the sender. No action is taken as the result of that frame. Q.921 2.10: Frame Abort Receipt of seven or more contiguous 1 bits shall be interpreted as an abort and the data link layer shall ignore the frame currently being received. Reaction of the ISAC-S TE a) A frame which does not start with a flag is discarded in the ISAC-S TE. A frame which does not end with a flag is one, that is aborted, i.e. if 2.9b does not apply then the ISAC-S TE - discards the frame, if it was an S-frame or, if it was an I or U-frame - generates an ISTA: RME (or RPFs and a RME) and - puts RSTA: RAB = 1 after the RME-Interrupt RAB = 1. A frame is supposed to be unbounded according to 5.8.5 if the byte counter RBCH, RBCL after RPF or RME exceeds 528. b) The frame is discarded by the ISAC-S TE if with U-frames or undefined framesit contains less or equal to 4 octets or with I-framesit contains less or equal to 5 octets with S-frames it contains less than 6 octets. For U-frames with a content between 4 and 5 octets exclusively or for I-frames between 5 and 6 octets exclusively an ISTA: RME interrupt is generated and afterwards the RSTA: CRC is set to 0. c) An S-frame is discarded. In the own-receiver-busy state I-frames are discarded. For an I-frame in the normal state and U frames, after several possible RPF interrupts and the final RME interrupt, the bit RSTA: CRC is set to 0 in this case. d) In case of an -S frame, the frame is discarded -U and I-framesRSTA: CRC is set to "0" in this case. e) the frame is discarded f) the frame is discarded Semiconductor Group 79 Functional Description The reaction to 2.10 has been already discussed under a) Necessary Software Actions The software should read the Register RSTA after a RME-interrupt. After having read RAB = 1 or CRC = 0, all frame contents read from the FIFO should be discarded and a CMDR: RMC should be written. After each RPF or RBCH, RBCL should be read and if it exceeds 528, CMDR: RRES should be written. In this way all invalid frames are discarded by the software. Data Overflow In case of a data overflow, which is only possible while receiving an I-frame or an U-frame with a non-empty information field, the ISAC-S TE interrupt with ISTA: RME and sets RSTA: RDO to 1. A RSTA: RDO and an ISTA: RFO are a hint that the dynamic reaction time of your software to the RPF, RME interrupt is too slow, so you should change your software. During the development phase you may set CMDR: RNR after an RDO, RFO-condition to protect against further errors, but the final solution can only be to exclude RDO, RFO conditions by an improved software design. Frame Rejection Condition Q.921 5.8.5: Frame Rejection Condition A frame rejection condition results from one of the following conditions: a) b) c) d) the receipt of an undefined frame (see 3.6.1, third paragraph) the receipt of a supervisory or unnumbered frame with incorrect length the receipt of an invalid N(R), or the receipt of a frame with an information field which exceeds the maximum established length. Upon occurrence of a frame rejection condition whilst in the multiple frame operation, the data link layer entity shall: - issue a MDL-ERROR-INDICATION primitive, and - initiate re-establishment (see 5.7.2). Upon occurrence of a frame rejection condition during establishment of or release from multiple frame operation, or whilst a data link is not established, the data link layer entity shall: - issue a MDL-ERROR-INDICATION primitive, and - discard the frame. Note: For satisfactory operation it is essential that a receiver is able to discriminate between invalid frames, as defined in 2.9, and frames with an information field which exceeds the maximum established length (see 3.6.11 item d). An unbounded frame may be assumed, and thus discarded, if two times the longest permissible frame plus two octets are received without a flag detection. Semiconductor Group 80 Functional Description For a better understanding we insert the text of 3.6.1, which is referred to in 5.8.5 and which reads: 3.6.1 Commands and responses The following commands and responses are used by either the user or the network data link layer entities and are represented in Q.921/table 5. Each data link connection shall support the full set of commands and responses for each application implemented. The frame types associated with each of the two applications are identified in Q.921/table 5. Frame types associated with an application not implemented shall be discarded and no action shall be taken as a result of that frame. For purposes of the LAPD procedures in each application, those frame types not identified in Q.921/table 5 are identified as undefined command and/or response control field. The actions to be taken are specified in 5.8.5. We include the original table 5 which is mentioned in 3.6.1: Semiconductor Group 81 Functional Description Table 7 Q.921 (Table 5) Application Format Information Transfer Supervisory Unacknowledged and MultipleFrame acknowledged Information Transfer Command s Responses 8 7 6 5 4 3 2 1 I(nformation) 0 4 N(R) P 5 1 4 P/F 5 1 4 P/F 5 1 4 P/F 5 RR (receive ready) 0 RNR (receive not ready) RNR (receive not ready) 0 REJ (reject) REJ (reject) 0 0 0 0 0 0 0 N(R) 0 0 0 0 1 0 N(R) 0 0 0 1 0 0 N(R) 0 1 1 P 1 1 1 1 4 0 0 0 F 1 1 1 1 4 UI (Unnumbered Information) 0 0 0 P 0 0 1 1 4 DISC (disconnect) 0 1 0 P 0 0 1 1 4 UA (unnumbered Acknowledgement) 0 1 1 F 0 0 1 1 4 FRMR (frame reject) 1 0 0 F 0 1 1 1 4 XID* (Exch. Ident) 1 0 1 P / F 1 1 1 1 4 DM (disconnected mode) Connection Management Oct et N(S) RR (receive ready) SABME (set async. balanced Mode extd). Unnumbered Encoding XID* (Exch. Ident) *Note: Use of the XID frame other than for parameter negotiation procedures (see 5.4) is for further study. The commands and responses in Q.921/table 5 are defined in 3.6.2 to 3.6.12 Semiconductor Group 82 Functional Description Reaction of the ISAC-S TE In the following various possible actions to be taken according to 5.8.5 parts a) through c) are discussed separately. a) There are different types of undefined frames: 1) I-frame which is not a command an ISTA: PCE-interrupt is generated 2) S-frame with bits 8-5 in Octet 4 = 0 an ISTA: PCE-interrupt is generated 3) A frame with bits 4-1 in octet 4 equal to "1101" (selective reject) an ISTA: PCE is generated 4) Frame with bits 2-1 in octet 4 equal to "11" but control field not contained in ISTA: RME interrupt; the control field can be read afterwards in RHCR (after having checked for invalid frame condition). 5) SABME, UI, DISC, not a command, DM, UA, FRMR not a response ISTA: RME interrupt; the control field can be read afterwards in RHCR, the C/R-bit in the SAPR-register (after having checked for invalid frame condition). b) If the length of the frame is too small 1.1.1b) applies and the frame is invalid. Therefore incorrect length can only mean: 1) S-frame with more than 6 octets an ISTA:PCE-interrupt is generated; the contents of the additional octets is discarded. 2) Undefined frames with 5 octets, bits 2-1 in octet 4 not being equal to "11" (e.g. modulo 8 S-frame) 3) SABME, BM, DISC, UA-frame with more than 5 octets an ISTA:PCE-interrupt is generated after ISTA: RME and identifying the frame by RHCR the RSTA:RDA bit is 1 if the frames had more than 5 octets and 0 if they had exactly 5 octets. 4) A FRMR with not exactly 10 octetsAfter a RME and identifying FRMR by reading RHCR-register, the software has to read RBCH, RBCL. If OV = 1 or RBC11-RBC0 = 0 ... 101 then the FRMR did not have exactly 10 octets. c) An invalid N(R) is one that does not meet the condition V(A) < N(R) < V(S) This condition is automatically checked within the device and in the case of an invalid N(R) an ISTA:PCE-interrupt is generated. An S-field response is done by the ISAC-S TE in all prescribed cases of invalid N(R) automatically. Semiconductor Group 83 Functional Description The processor should read RBCH, RBCL after each RPF, RME interrupt. If after an RPF or RME the byte count exceeds 528 then CMDR:RRES should be written (abort of frame). The frame was invalid in this case but it was not a frame rejection condition. If after a RME the byte count was between 260 and 528 inclusively and no other invalidity condition according to section 1 applies or a data overflow according to section 2 occurred then a frame rejection condition is detected. Necessary Software Reactions The software can find out all frame rejection conditions either by receiving PCE or by checking RSTA, SAPR, RHCR, RBCH, RBCL after a RME interrupt, and RBCH, RBCL after an RPF interrupt. In case of U-frames it has to be checked before, whether or not it is an invalid frame and has only to be discarded or, whether it was valid but leads to a frame rejection condition. (Only valid frames can lead to frame rejection conditions according to 5.8.4 of Q.921). In case of a frame rejection condition the software has to take the actions defined in 5.7.2 and issue a MDL-ERROR-INDICATION. The particular action in 5.7.2 reads: 5.7.2 Procedures In all re-establishment situations, the data link layer entity shall follow the procedures defined in 5.5.1. All locally generated conditions for re-establishment will cause the transmission of the SABME. In case of data link layer and peer initiated re-establishments, the data link layer entity shall also - Issue a MDL-ERROR-INDICATION primitive to the connection management entity: and - rf V(S) > V(A) prior to re-establishment issue a DL-ESTABLISH-INDICATION primitive to layer 3 and discard all l-queues. In case of layer-3 initiated re-establishment, or if a DL-ESTABLISH-REQUEST primitive occurs pending re-establishment, the DL-ESTABLISH-CONFIRM primitive shall be used. A frame rejection condition is not a peer initiated re-establishment. 5.5.1 is pretty voluminous. Here just the necessary actions to be done with the ISAC-S TE shall be given, in case the re-establishment is successful at once: - the software should set the ISAC-S TE into non-auto mode by writing the Mode register MODE: 6xH. Further actions that result from switching to non-auto mode should also be taken according. - it should write FIFO : 76H, 6FH, CMDR : XTF to send a SABME-command with p = 1. - upon having received a correct UA-frame it should - write CMDR : XRES, RRES to set V(S) = V(A) = V(R) = 0 - write MODE: 3xH to re-enter auto mode for the multiple-frame established state. If the re-establishment is not successful at once, in the non-auto mode further software actions according to 5.5.1 have to be taken. Semiconductor Group 84 Functional Description Further Criteria Leading to a Re-Establishment Q.921 5.7.1: Criteria for Re-Establishment 5.7.1 Criteria for re-establishment The criteria for re-establishing the multiple frame mode of operation are defined in this section by the following conditions: a) The receipt while in the multiple frame mode of operation, of an SABME; b) The receipt of a DL-ESTABLISH-REQUEST primitive from layer 3 (see 5.5.1.1); c) The occurrence of N200 re-transmission failures while in the timer recovery condition (see 5.6.7) d) The occurrence of a frame rejection condition as identified in 5.8.5; e) On the receipt, while in the multiple frame mode of operation of an FRMR response frame (see 5.8.6); f) The receipt, while in the multiple frame mode of operation, of an unsolicited DM response with the F bit set to 0 (see 5.8.7); g) The receipt while in the timer recovery condition, of a DM response with the F bit set to 1. Reaction of the ISAC-S TE a) after having checked for validity and non-occurrence of a frame rejection condition, the error free SABME can be identified after RME-Interrupt by reading the RHCR-register; the multiple frame est/timer recovery discrimination can be done by reading STAR2: TREC b) - c) A TIN-Interrupt occurs (of course MODE: TMD has to have been 1) d) see section 3 e) see a) f) see a) g) see a) Necessary Software Reactions The same actions as in section 3 have to be taken. In addition, in case of a) the necessary discrimination for the software is possible by reading STAR2: WFA while still in auto mode. If WFA = 1 then V(S) > V(A); if WFA = 0, then V(S) = V(A). Semiconductor Group 85 Functional Description Further Possible Error Conditions Appendix II of Q.921: Further Possible Error Conditions Table 8 Q.921 Management Entity Actions for MDL Error Indications Error Type Error Error Affected Network Code Condition States Management Action Receipt of A Supervisory 7 Error log unsolicited (F = 1) response B DM(F = 1) 7, 8 Error log C UA(F = 1) D UA(F = 1) E Receipt of DM 7, 8 response (F = 0) SABME 7, 8 Error log SABME 5 DISC 6 Status Inquiry 8 TEI check procedure; then, if TEI: - free, remove TEI - single, no action multiple: TEI removal procedure Error log Peer initiated F Reestablishmen t Unsuccessful G Retransmission (N200 times) H I Semiconductor Group 4, 7, 8 TEI removal procedure or TEI check procedure; then, if 4, 5, 6, 7, 8 TEI: - free, remove TEI - single, no action multiple: TEI removal procedure 86 Error log User Management Action Dependent on implementation Dependent on implementation TEI identity verify procedure or remove TEI Dependent on implementation Dependent on implementation TEI identity verify procedure or remove TEI Dependent on implementation Functional Description Table 8 Q.921 Management Entity Actions for MDL Error Indications (cont'd) Error Type Error Error Affected Network Code Condition States Management Action Other J N(R) Error 7, 8 Error log K Receipt of FRMR response Receipt of non implemented frame Receipt of I-field not permitted Receipt of frame with wrong size N201 Error 7, 8 Error log L M (see Note 2) N O User Management Action Dependent on implementation Dependent on implementation 4, 5, 6, 7, 8 Error log Dependent on implementation 4, 5, 6, 7, 8 Error log Dependent on implementation Dependent on implementation 4, 5, 6, 7, 8 Error log 4, 5, 6, 7, 8 Error log Dependent on implementation Note 1: For the description of the affected states see Annex B. Note 2: According to Q.921 5.8.5 this error code will never be generated. Reactions of the ISAC-S TE and Necessary Software Reactions As the auto mode is only to be used in states 7, 8 and as it has to be switched to non-auto mode where in states 1-6, we do not have to deal with error code G and H. A) The ISAC-S does not react at all (our implementation). The software is not informed, as no action is mandatory according to Q.921. B) see further Criteria Leading to a Reestablishment" C) see further Criteria Leading to a Reestablishment D) see further Criteria Leading to a Reestablishment E) see further Criteria Leading to a Reestablishment F see further Criteria Leading to a Reestablishment I) see further Criteria Leading to a Reestablishment J) see Frame Rejection Condition K) see further Criteria Leading to a Reestablishment L) see Frame Rejection Condition M) N) see Frame Rejection Condition O) only internal software timer, no device action. Conclusion: For your error-processing with ISAC-S we suggest to implement the software design shown in the following figures 35 through 38 into your interrupt service routine. Semiconductor Group 87 Functional Description RME & /TIN & /PCE RSTA:RAB = 1 or CRC = 0 ? Y CMDR:RHR Discard frame cont Y Please change your software: dynamic reaction time is too slow N Futher analysis outside the auto-mode link Y Re-establishment of the link N RSTA:RDO = 1 or ISTA:RFO = 1 ? N RSTA: which link, auto-mode ? Y RBCH, RBCL > 260 ? N CMDR:RMC Cont. -> Layer 3 I-frame RHCR, SAPR : C/R control field Not contained in table 5 of Q.921 3.6.1 Re-establishment of the link ? U-frame U-frame processing Figure 35 Interrupt Service Routine after RME Semiconductor Group 88 ITD05896 Functional Description RPF & /TIN & /PCE RBCH, RBCL > 528 ? Y CMDR:RHR Discard frame cont Note: In this case the software has to react instantaneously to the RPF ( < 500 s) N Read FIFO CMDR:RMC TIN or PCE RSC Re-establishment of the link Change status variable Note: For the congestion procedure defined in 1 TRG of the Deutsche Bundespost refer to the Technical Manual XDU or RFO Please change your software: Dynamic reaction is too slow ITD05895 Figure 36 Interrupt Service Routines after RPF (top), TIN or PCE (middle left), RSC (middle right), and XDU or RFO (bottom) Semiconductor Group 89 Functional Description XPR & /TIN & /PCE Has a frame been sent since last CMDR:XRES ? N End Y A frame is currently transmitted Continue writing the contents of the frame to XFIFO & issuing Xmit command Y ? N Last frame written to XFIFO was an I-frame The transmission of the I-frame was successful and has been acknowledged by the peer station Y ACK1 ? N SRC * N Transmission of the last frame has finished Xmit command ACK2 ? Y ACK1 & ACK2 * Special Request Condition : Last frame written to the XFIFO was an answer to an identity request following a yet unacknowledged I-frame Figure 37 Interrupt Service Routine after XPR Semiconductor Group 90 ITD05893 Functional Description XMR & /TIN & /PCE SRC ? N Re-transmit the frame sent last Y Re-transmit the - frame sent last ITD05894 Figure 38 Interrupt Service Routine after XMR Semiconductor Group 91 Functional Description 7 MULTIPLE FRAME ESTABLISHED DL ESTABLISH REQUEST DISCARD I QUEUE DL RELEASE REQUEST DISCARD I QUEUE DL-DATA REQUEST PUT IN I QUEUE I FRAME QUEUED UP PEER RECEIVER BUSY STAR:RRNR YES NO ESTABLISH DATA LINK RC = 0 P=1 I FRAME QUEUED UP (V)S = V(A) + K YES STAR2:WFA NO SET LAYER 3 INITIATED TX DISC XFIFO CMDR XTF 7 MULTIPLE FRAME ESTABLISHED GET NEXT I QUEUE ENTRY XFIFO I FRAME QUEUED UP MODE NAM 5 AWAITING ESTABLISHM. STOP T203 RESTART T200 P=0 MODE NAM TXI COMMAND 6 AWAITING RELEASE CMDR:XIF V(S) = V(S) + 1 CLEAR ACKNOWLEDGE PENDING T200 RUNNING YES NO STOP T203 START T200 Note: The regeneration of this signal does not affect the sequence integrity of the I queue. ITD02365 Figure 39a Semiconductor Group 92 7 MULTIPLE FRAME ESTABLISHED Functional Description 7 MULTIPLE FRAME ESTABLISHED TIMER T200 EXPIRY MDL REMOVE REQUEST PERSISTENT DEACTIVATION TRANSMIT ENQUIRY DISCARD I AND UI QUEUES DISCARD I AND UI QUEUES RC = 0 DL RELEASE INDICATION DL RELEASE INDICATION STOP T200 STOP T203 STOP T200 STOP T203 1 TEI UNASSIGNED 4 TEI ASSIGNED TIMER T203 EXPIRY CMDR STI RC = 0 YES PEER BUSY NO GET LAST TRANSMITTED I FRAME TRANSMIT ENQUIRY 8 TIMER RECOVERY STAR2: TREC V(S) = V(S) - 1 P=1 ITD02366 TX I COMMAND V(S) = V(S) + 1 CLEAR ACKNOWLEDGE PENDING START T200 RC = RC + 1 8 TIMER RECOVERY STAR2: TREC Figure 39b Semiconductor Group 93 Functional Description 7 MULTIPLE FRAME ESTABLISHED RME RME RME SABME DISC UA RCHR: RCHR: RCHR: F=P DISCARD I QUEUE TX UA STORE STAR2: WFA F=P XFIFO CMDR XTF CLEAR EXCEPTION CONDITIONS YES TX UA XFIFO CMDR XTF MDL-ERROR INDICATION (F) DL-RELEASE INDICATION V(S) = V(A) STOP T200 STOP T203 STAR2:WFA = 0 MODE NAM NO 4 TEI ASSIGNED DISCARD I QUEUE DL ESTABLISH INDICATION STOP T200 STOP T203 CMDR:RHR;XRES V(S) = 0 V(A) = 0 V(R) = 0 7 MULTIPLE FRAME ESTABLISHED ITD02367 Figure 39c Semiconductor Group 94 MDL-ERROR INDICATION (C,D) 7 MULTIPLE FRAME ESTABLISHED Functional Description 7 MULTIPLE FRAME ESTABLISHED RME CLEAR OWN RECEIVER BUSY SET OWN RECEIVER BUSY DM RHCR: F=1 CLEAR RECEIVER BUSY YES RHCR NO MDL-ERROR INDICATION (E) ESTABLISH DATA LINK CLEAR LAYER 3 INITIATED YES CLEAR RECEIVER BUSY NO NO MDL-ERROR INDICATION (B) 7 MULTIPLE FRAME ESTABLISHED SET OWN RECEIVER BUSY CMDR:RNR = 1 YES STAR:XRNR CLEAR OWN RECEIVER BUSY CMDR:RNR = 0 F=0 F=0 TX RNR RESPONSE TX RR RESPONSE CLEAR ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING MODE NAM 5 AWAITING ESTABLISHM. 7 MULTIPLE FRAME ESTABLISHED Note: These signals are generated outside of this SDL representation, and may be generated by the connection management entity. Figure 39d Semiconductor Group 95 ITD02368 STAR:XRNR Functional Description 7 MULTIPLE FRAME ESTABLISHED REJ RR CLEAR PEER RECEIVER BUSY COMMAND RSC / CLEAR PEER RECEIVER BUSY STAR:RRNR NO NO F=1 YES YES COMMAND F=1 NO NO NO NO MDL-ERRORINDICATION (A) YES ENQUIRY RESPONSE STAR:RRNR YES YES P=1 RSC / P=1 YES MDL-ERRORINDICATION (A) STAR2:SDET ENQUIRY RESPONSE ITD05656 1 2 Figure 39 f Figure 39 f Figure 39e Semiconductor Group 96 STAR2:SDET Functional Description 1 2 _ N(R) <_ V(S) V(A) < NO NO YES _ N(R) <_ V(S) V(A) < YES XPR / PCE N(R) = V(S) N(R) ERROR RECOVERY NO YES V(A) = N(R) STAR2:WFA MODE NAM XPR / YES V(A) = N(R) 5 AWAITING ESTABLISHM. N(R) = V(A) STAR2:WFA STOP T200 START T203 NO INVOKE RETRANSMISSION STOP T200 START T203 V(A) = N(R) 7 MULTIPLE FRAME ESTABLISHED RESTART T200 7 MULTIPLE FRAME ESTABLISHED ITD02370 Figure 39f Semiconductor Group 97 XMR / Functional Description 7 MULTIPLE FRAME ESTABLISHED RME RNR FRMR RHCR: RSC / SET PEER RECEIVER BUSY MDL-ERROR INDICATION (K) STAR:RRNR NO COMMAND ESTABLISH DATA LINK YES F=1 NO P=1 CLEAR LAYER 3 INITIATED NO MODE NAM MDL-ERRORINDICATION (A) YES ENQUIRY RESPONSE YES 5 AWAITING ESTABLISHM. STAR2:SDET _ N(R) <_ V(S) V(A) < NO YES XPR / N(R) ERROR RECOVERY V(A) = N(R) STAR2:WFA MODE NAM STOP T203 5 AWAITING ESTABLISHM. RESTART T200 RC = 0 7 MULTIPLE FRAME ESTABLISHED ITD02371 Figure 39g Semiconductor Group 98 PCE Functional Description 7 MULTIPLE FRAME ESTABLISHED I COMMAND OWN RECEIVER BUSY YES NO N(S) = V(R) DISCARD INFORMATION NO YES DISCARD INFORMATION V(R) = V(R) + 1 NO P=1 YES REJECT EXCEPTION CLEAR REJECT EXCEPTION NO NOTE 2 F=1 YES RME DL-DATA INDICATION RFIFO, RHCR NO P=1 SET REJECT EXCEPTION STAR2:SDET YES YES P=1 TX RNR CLEAR ACKNOWLEDGE PENDING F=P NO ACKNOWLEDGE PENDING YES TX REJ F=P STAR2:SDET NO ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING TX RR STAR2:SDET NOTE 1 SET ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING ITD05657 3 Figure 39 i Note 1: Processing of acknowledge pending is descripted on figure 39 i Note 2: This SDL representation does not include the optional procedure in Appendix I. Figure 39h Semiconductor Group 99 Functional Description 3 _ N(R) <_ V(S) V(A) < NO YES PEER RECEIVER BUSY N(R) ERROR RECOVERY NO YES MODE NAM XPR / V(A) = N(R) N(R) = V(S) 5 AWAITING ESTABLISHM. NO STAR2:WFA YES XPR / V(A) = N(R) N(R) = V(A) STAR2:WFA NO STOP T200 V(A) = N(R) RESTART T203 RESTART T200 7 MULTIPLE FRAME ESTABLISHED ITD02373 Figure 39i Semiconductor Group 100 YES PCE Functional Description 7 MULTIPLE FRAME ESTABLISHED ACKNOWLEDGE PENDING ACKNOWLEDGE PENDING NO YES CLEAR ACKNOWLEDGE PENDING F=0 TX RR STAR2:SDET 7 MULTIPLE FRAME ESTABLISHED ITD02374 Figure 39j Semiconductor Group 101 Functional Description 8 TIMER RECOVERY DL ESTABLISH REQUEST DL ESTABLISH REQUEST DL-DATA REQUEST DISCARD I QUEUE DISCARD I QUEUE PUT IN I QUEUE ESTABLISH DATA LINK RC = 0 P=1 I FRAME QUEUED UP SET LAYER 3 INITIATED TX DISC 8 TIMER RECOVERY MODE NAM 5 AWAITING ESTABLISHM. XFIFO CMDR XTF RESTART T200 MODE NAM 6 AWAITING RELEASE ITD02375 Figure 40a Semiconductor Group 102 I FRAME QUEUED UP Functional Description 8 TIMER RECOVERY MDL REMOVE REQUEST PERSISTENT DEACTIVATION DISCARD I AND UI QUEUES DISCARD I AND UI QUEUES MDL-ERROR INDICATION(I) DL-RELEASE INDICATION DL-RELEASE INDICATION ESTABLISH DATA LINK STOP T200 STOP T200 TIMR TIMR MODE NAM MODE NAM 1 TEI UNASSIGNED 4 TEI ASSIGNED TIMER T200 EXPIRY RC = N200 YES NO TIN YES V(S) = V(A) NO YES PEER BUSY NO TRANSMIT ENQUIRY GET LAST TRANSMITTED I FRAME V(S) = V(S) - 1 P=1 CLEAR LAYER 3 INITIATED MODE NAM 5 AWAITING ESTABLISHM. TX I COMMAND V(S) = V(S) + 1 CLEAR ACKNOWLEDGE PENDING START T200 RC = RC + 1 8 TIMER RECOVERY Figure 40b Semiconductor Group 103 ITD02376 Functional Description 8 TIMER RECOVERY RME RME RME SABME DISC UA RHCR: RHCR: RHCR: F=P DISCARD I QUEUE TX UA STORE STAR2: WFA F=P XFIFO CMDR XTF CLEAR EXCEPTION CONDITIONS YES TX UA XFIFO CMDR XTF MDL-ERROR INDICATION (F) DL-RELEASE INDICATION V(S) = V(A) STOP T200 STAR2:WFA = 0 MODE NAM NO 4 TEI ASSIGNED DISCARD I QUEUE DL ESTABLISH INDICATION STOP T200 START T203 CMDR:RHR;XRES V(S) = 0 V(A) = 0 V(R) = 0 7 MULTIPLE FRAME ESTABLISHED STAR2:TREC Figure 40c Semiconductor Group 104 ITD02377 MDL-ERROR INDICATION (C, D) 8 TIMER RECOVERY Functional Description 8 TIMER RECOVERY RME CLEAR OWN RECEIVER BUSY SET OWN RECEIVER BUSY DM RHCR: F=1 CLEAR RECEIVER BUSY YES RHCR NO MDL-ERROR INDICATION (E) YES NO OWN RECEIVER BUSY NO MDL-ERROR INDICATION (B) YES SET OWN RECEIVER BUSY CMDR:RNR = 1 STAR:XRNR CLEAR OWN RECEIVER BUSY CMDR:RNR = 0 ESTABLISH DATA LINK F=0 F=0 CLEAR LAYER 3 INITIATED TX RNR RESPONSE TX RR RESPONSE CLEAR ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING MODE NAM 5 AWAITING ESTABLISHM. 8 TIMER RECOVERY Note: These signals are generated outside of this SDL representation, and may be generated by the connection management entity. Figure 40d Semiconductor Group 105 ITD02378 STAR:XRNR Functional Description 8 TIMER RECOVERY RR REJ CLEAR PEER RECEIVER BUSY COMMAND RSC / STAR:RRNR NO YES P=1 YES F=1 NO NO NO _ N(R) <_ V(S) V(A) < YES YES ENQUIRY RESPONSE STAR2:SDET XPR / V(A)=N(R) STAR2:WFA _ N(R) <_ V(S) V(A) < STOP T200 NO START T203 YES XPR / PCE N(R) ERROR RECOVERY V(A) = N(R) STAR2:WFA INVOKE RETRANSMISSION XMR / MODE NAM 8 TIMER RECOVERY 5 AWAITING ESTABLISHM. 7 MULTIPLE FRAME ESTABLISHED ITD02379 Figure 40e Semiconductor Group 106 STAR2:TREC Functional Description 8 TIMER RECOVERY RME RNR FRMR RCHR: RSC / MDL-ERROR INDICATION (K) BUSY STAR:RRNR COMMAND NO YES ESTABLISH DATA LINK F=1 YES CLEAR LAYER 3 INITIATED NO P=1 NO NO MODE NAM _ N(R) <_ V(S) V(A) < YES YES ENQUIRY RESPONSE V(A) = N(R) 5 AWAITING ESTABLISHM. XPR / _ N(R) <_ V(S) V(A) < STAR2:WFA STAR2:SDET NO RESTART T200 RC = 0 YES XPR / V(A) = N(R) STAR2:WFA N(R) ERROR RECOVERY PCE INVOKE RETRANSMISSION XMR / MODE NAM 8 TIMER RECOVERY 7 MULTIPLE FRAME ESTABLISHED 5 AWAITING ESTABLISHM. ITD02380 Figure 40f Semiconductor Group 107 STAR2:TREC Functional Description 8 TIMER RECOVERY I COMMAND OWN RECEIVER BUSY YES NO N(S) = V(S) DISCARD INFORMATION NO YES DISCARD INFORMATION V(R) = V(R) + 1 NO P=1 YES REJECT EXCEPTION CLEAR REJECT EXCEPTION NO NOTE 2 F=1 YES RME DL-DATA INDICATION RFIFO, RHCR NO P=1 SET REJECT EXCEPTION TX RNR STAR2:SDET YES YES P=1 CLEAR ACKNOWLEDGE PENDING F=P NO ACKNOWLEDGE PENDING YES TX REJ F=P STAR2:SDET NO ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING TX RR STAR2:SDET NOTE 1 SET ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING ITD05658 4 Figure 40 h Note 1: Processing of acknowledge pending is descripted on figure 40 i Note 2: This SDL representation does not include the optional procedure in Appendix I. Figure 40g Semiconductor Group 108 Functional Description 4 _ N(R) <_ V(S) V(A) < NO YES XPR / N(R) ERROR RECOVERY V(A) = N(R) STAR2:WFA PCE MODE NAM 8 TIMER RECOVERY 5 AWAITING ESTABLISHM. Figure 40h 8 TIMER RECOVERY ACKNOWLEDGE PENDING ACKNOWLEDGE PENDING NO YES CLEAR ACKNOWLEDGE PENDING F=0 TX RR STAR2:SDET 8 TIMER RECOVERY Figure 40i Semiconductor Group 109 ITD02383 ITD02382 Functional Description RELEVANT STATES (NOTE 1) DL UNIT DATA REQUEST UI FRAME QUEUED UP PLACE IN UI QUEUE REMOVE UI FRAME FROM QUEUE UI FRAME QUEUED UP P=0 NOTE 2 TX UI COMMAND XFIFO CMDR: XTF RME UI COMMAND RHCR DL UNIT DATA INDICATION NOTE 2 NOTE 2 Note 1: The relevant states are as follows 4 TEI-assigned 5 Awaiting-establishement 6 Awaiting-release 7 Multiple-frame-established 8 Timer-recovery Note 2: The data link layer returns to the state it was in prior to the events shown. ITD02384 Figure 41a Semiconductor Group 110 Functional Description RELEVANT STATES (NOTE 1) CONTROL FIELD ERROR (W) INFO NOT PERMITTED (X) INCORRECT LENGHT (X) MDL-ERROR INDICATION (L,M,N,O) ESTABLISH DATA LINK CLEAR LAYER 3 INITIATED 5 AWAITING ESTABLISHM. Note 1: The relevant states are as follows 7 Multiple-frame-established 8 Timer-recovery ITD02385 Figure 41b Semiconductor Group 111 PCE / 1 FRAME TOO LONG (Y) Functional Description RELEVANT STATES (NOTE 1) CONTROL FIELD ERROR (W) INFO NOT PERMITTED (X) INCORRECT LENGTH (X) I FRAME TOO LONG (Y) MDL-ERRORINDICATION (L, M, N, O) NOTE 2 Note 1: The relevant states are as follows: 4 TEI-assigned 5 Awaiting-establishment 6 Awaiting-release Note 2: The data link layer returns to the state it was in prior to the events shown Figure 41c Semiconductor Group 112 ITD02577 Functional Description N(R) ERROR RECOVERY MDL-ERROR INDICATION(J) PCE ESTABLISH DATA LINK ESTABLISH DATA LINK CLEAR EXCEPTION CONDITION CMDR:RHR,XRES MODE: NAM RC = 0 P=1 CLEAR EXCEPTION CONDITIONS TRANSMIT ENQUIRY CMDR:RHR,XRES CLEAR PEER RECEIVER BUSY P=1 CLEAR REJECT EXCEPTION OWN RECEIVER BUSY YES NO CLEAR LAYER 3 INITIATED TX SABME XFIFO CMDR:XTF RESTART T200 STOP T203 CLEAR OWN RECEIVER BUSY CMDR:RNR = 0 TX RR COMMAND TX RNR COMMAND CLEAR ACKNOWLEDGE PENDING CLEAR ACKNOWLEDGE PENDING START T200 ITD02386 Figure 41d Semiconductor Group 113 Functional Description ENQUIRY RESPONSE INVOKE RETRANSMISSION F=1 V(S) = N(R) OWN RECEIVER BUSY YES NO XMR YES V(S) =V(S) - 1 NO I FRAME QUEUED UP TX RNR RESPONSE TX RR RESPONSE STAR2:SDET STAR2:SDET NOTE BACK TRACK ALONG I QUEUE CLEAR ACKNOWLEDGE PENDING Note: The generation of the correct number of signals in order to cause the required retransmission of I frames does not alter their sequence integrity. ITD02387 Figure 41e Semiconductor Group 114 Operational Description 3 Operational Description The ISAC-S TE, designed for the connection of subscribers to an ISDN using a standard S/T interface, has the following application, corresponding to the operating mode explained in chapter 2: Terminal Equipment TE1, TA e.g. 3.1 ISDN-feature telephone, ISDN-voice/data workstation Terminal Adapter for non-ISDN terminals (TE2) Microprocessor Interface Operation The ISAC-S TE is programmed via an 8-bit parallel microcontroller interface. Easy and fast microprocessor access is provided by 8-bit address decoding on the chip. Depending on the chip package (P-DIP-40, P-LCC-44, P-MQFP-64) either one or three types of P buses are provided: P-DIP-40 package: The ISAC-S TE microcontroller interface is of the Siemens/Intel multiplexed address/data bus type with control signals CS, WR, RD, ALE. P-LCC-44/P-MQFP-64 package: The ISAC-S TE microcontroller interface can be selected to be either of the (1) - Motorola type with control signals CS, R/W, DS (2) - Siemens/Intel non-multiplexed bus type with control signals CS, WR, RD (3) - or of the Siemens/Intel multiplexed address/data bus type with control signals CS, WR, RD, ALE. The selection is performed via pin ALE as follows: ALE tied to VDD (1) ALE tied to VSS (2) Edge on ALE (3). The occurrence of an edge on ALE, either positive or negative, at any time during the operation immediately selects interface type (3). A return to one of the other interface types is possible only if a hardware reset is issued. Notes: 1) If the multiplexed address/data bus type (3) is selected, the unused address pins A0-A5 are internally pulled low and may thus be left open. It is however recommended to tie the unused input pins to a VDD voltage level. 2) If the non-multiplexed bus types (1) or (2) are selected, the EAW line can no longer be used since pin 10 EAW/A5 has the function of an address pin (PLCC-44 only). Semiconductor Group 115 Operational Description The microprocessor interface signals are summarized in table 9. Table 9 P Interface of the ISAC(R)-S TE Pin No. Pin No. Function Pin No. Symbol Input (I) P-DIP-40 P-LCC-44 P-MQFP-64 Output (O) Open Drain (OD) 37 38 39 40 1 2 3 4 41 42 43 44 1 2 3 4 37 38 39 40 41 42 43 44 AD0/D0 AD1/D1 AD2/D2 AD3/D3 AD4/D4 AD5/D5 AD6/D6 AD7/D7 I/O I/O I/O I/O I/O I/O I/O I/O Multiplexed Bus Mode: Address/Data bus. Transfers addresses from the P system to the ISAC-S TE and data between the P system and the ISAC-S TE. Non-Multiplexed Bus Mode: Data bus. Transfers data between the P system and the ISAC-S TE. 34 37 27 CS I 38 28 R/W I 38 28 WR I Chip Select. A 0 ("low") on this line selects the ISAC-S TE for a read/write operation. Read/Write. A 1 ("high"), identifies a valid P access as a read operation. A 0, identifies a valid P access as a write operation (Motorola bus mode). Write. This signal indicates a write operation (Siemens/Intel bus mode). 39 29 DS I 36 39 29 RD I 20 23 8 INT OD Interrupt Request. The signal is activated when the ISAC-S TE requests an interrupt. It is an open drain output. 33 36 26 ALE I Address Latch Enable. A high on this line indicates an address on the external address bus (multiplexed bus type only). ALE also selects interface mode. 40 30 A0 I Address Bit 0 (non-multiplexed bus type). 6 51 A1 I Address Bit 1 (non-multiplexed bus type). 5 50 A2 I Address Bit 2 (non-multiplexed bus type). 18 64 A3 I Address Bit 3 (non-multiplexed bus type). 17 63 A4 I Address Bit 4 (non-multiplexed bus type). 10 55 A5 I Address Bit 5 (non-multiplexed bus type). 35 Semiconductor Group Data Strobe. The rising edge marks the end of a valid read or write operation (Motorola bus mode). Read. This signal indicates a read operation (Siemens/Intel bus mode). 116 Operational Description 3.2 Interrupt Structure and Logic Since the ISAC-S TE provides only one interrupt request output (INT), the cause of an interrupt is determined by the microprocessor by reading the Interrupt Status Register ISTA. In this register, seven interrupt sources can be directly read. The LSB of ISTA points to eight noncritical interrupt sources which are indicated in the Extended Interrupt Register EXIR (figure 42). INT RME RPF RSC XPR TIN CISQ SIN EXI MASK RME RPF RSC XPR TIN CISQ SIN EXI ISTA SQIE XMR XDU PCE RFO SOV MOS SAW WOV EXIR SQRR C O D R 0 MDR1 MER1 MDA1 MAB1 MDR0 MER0 MDA0 MAB0 MOSR MRE1 MXE1 MRE0 MXE0 MOCR Figure 42 ISAC(R)-S TE Interrupt Structure Semiconductor Group SQC BAS 117 CI1E CIC0 CIC1 SQXR CIR0 R IOM -2 only CIR1 ITD02578 Operational Description A read of the ISTA register clears all bits except EXI and CISQ. CISQ is cleared by reading CIR0. A read of EXIR clears the EXI bit in ISTA as well as the EXIR register. When all bits in ISTA are cleared, the interrupt line (INT) is deactivated. Each interrupt source in ISTA register can be selectively masked by setting to "1" the corresponding bit in MASK. Masked interrupt status bits are not indicated when ISTA is read. Instead, they remain internally stored and pending, until the mask bit is reset to zero. Reading the ISTA while a mask bit is active has no effect on the pending interrupt. In the event of an extended interrupt and of a C/I- or S/Q channel change, EXI and CISQ are set even when the corresponding mask bits in MASK are active, but no interrupt (INT) is generated. Except for CISQ and MOS all interrupt sources are directly determined by a read of ISTA and (possibly) EXIR. CISQ-Interrupt Logic - A CISQ interrupt may originate - from a change in the received S/Q code (SQC) - from a change in the received C/I channel 0 code (CIC0) or (in the case of IOM-2 terminal mode only) - from a change in the received C/I channel 1 code (CIC1). The three corresponding status bits SQC, CIC0 and CIC1 are read in the CIR0 register. SQC and CIC1 can be individually disabled by clearing the enable bit SQIE (SQXR register) or, respectively, CI1E (SQXR register). In this case the occurrence of a code change in SQRR/ CIR1 will not be displayed by SQC/CIC1 until the corresponding enable bit has been set to one. Bits SQC, CIC0 and CIC1 are cleared by a read of CIR0. An interrupt status is indicated every time a valid new code is loaded in SQRR, CIR0 or CIR1. But in case of a code change, the new code is not loaded until the previous contents have been read. When this is done and a second code change has already occurred, a new interrupt is immediately generated and the new code replaces the previous one in the register. The code registers are buffered with a FIFO size of two. Thus, if several consecutive codes are detected, only the first and the last code is obtained at the first and second register read, respectively. Semiconductor Group 118 Operational Description MOS-Interrupt Logic The MONITOR Data Receive (MDR) and the MONITOR End of Reception (MER) interrupt status bits have two enable bits, MONITOR Receive interrupt Enable (MRE) and MR bit Control (MRC). The MONITOR channel Data Acknowledged (MDA) and MONITOR channel Data Abort (MAB) interrupt status bits have a common enable bit MONITOR Interrupt Enable (MXE). MRE prevents the occurrence of the MDR status, including when the first byte of a packet is received. When MRE is active (1) but MRC is inactive, the MDR-interrupt status is generated only for the first byte of a receive packet. When both MRE and MRC are active, MDR is generated and all received monitor bytes - marked by a 1-to-0 transition in MX bit - are stored. (Additionally, an active MRC enables the control of the MR handshake bit according to the MONITOR channel protocol.) Control of Edge-Triggered Interrupt Controllers The INT output is level active. It stays active until all interrupt sources have been serviced. If a new status bit is set while an interrupt is serviced, the INT line stays active. This may cause problems if the ISAC-S TE is connected to edge-triggered interrupt controllers (figure 43). To avoid these problems, it is recommended to mask all interrupts at the end of the interrupt service program and to enable the interrupts again. This is done by writing FFH to the MASK register and to write back the old value of the MASK register (figure 44). Semiconductor Group 119 Operational Description 3 1 INT 5 2 4 ITD05430 A status bit is set. This causes an interrupt. The microprocessor starts its service routine and reads the status registers. A new status bit is set before the first status bit has been read. The first status bit is read. The INT output stays active but the interrupt controller will not serve the interrupt (edge triggered). Figure 43 INT Handling 3 1 INT 2 4 5 6 7 8 9 ITD05431 to see above 'FF' is written to the MASK register. This masks all interrupts and returns the INT output to its inactive state. The old value is written to the MASK register. This will activate the INT output if an interrupt source is still active. The microprocessor starts a new interrupt service program. The last status bit is read. The INT output is inactive. Figure 44 Service Program for Edge-Triggered Interrupt Controllers Semiconductor Group 120 Operational Description ~~ DCL ~~ INT ~~ RD ITD02388 Figure 45 Timing of INT Pin The INT line is switched with the rising edge of DCL. If no pending interrupts are internally stored, a reading of ISTA respectively EXIR or CIR0 switches the INT line to high as indicated in figure 45. 3.3 Control of Layer 1 3.3.1 Activation/Deactivation of IOM(R) Interface The IOM interface can be switched off in the inactive state, reducing power consumption to a minimum. In this deactivated state the clock line is low and the data lines are high. The IOM interface can be kept active while the S interface is deactivated by setting the CFS bit to "0" (SQXR register). This is the case after a hardware reset. If the IOM interface should be switched off while the S interface is deactivated, the CFS bit should be set to "1". In this case the internal oscillator is disabled when no signal (info 0) is present on the S bus. If the TE wants to activate the line, it has first to activate the IOM interface either by using the "Software Power-Up" function (SPCR:SPU bit) or by setting the CFS bit to "0" again. For the TE case the deactivation procedure is shown in figure 46. After detecting the code DIU (Deactivate Indication Upstream, i.e. from TE to NT/LT-S) the layer 1 of the ISAC-S TE responds by transmitting DID (Deactivate Indication Downstream) during subsequent frames and stops the timing signals synchronously with the end of the last C/I (C/I0) channel bit of the fourth frame. Semiconductor Group 121 Operational Description R IOM -2 Deactivated FSC DIU DIU DIU DIU DIU DIU DIU DIU DIU DR DR DR DR DR DID DID DID DID IDP1 (DU) IDP0 (DD) B1 B2 D MONO D CIO CIO DCL ITD05963 Figure 46 Deactivation of the IOM(R) Interface The clock pulses will be enabled again when the IDP1 line is pulled low (bit SPU, SPCR register) i.e. the C/I command TIM = "0000" is received by layer 1, or when a non-zero level on the S-line interface is detected. The clocks are turned on after approximately 0.2 to 4 ms depending on the capacitances on XTAL 1/2. DCL is activated such that its first rising edge occurs with the beginning of the bit following the C/I (C/I0) channel. After the clocks have been enabled this is indicated by the PU code in the C/I channel and, consequently, by a CISQ interrupt. The IDP1 line may be released by resetting the Software Power-Up bit SPCR:SPU=0, and the C/I code written in CIX0 is output on IDP1. Semiconductor Group 122 Operational Description CISQ CIS0 = TIM Int. SPU = 0 ~~ SPU = 1 FSC TIM TIM PU PU PU ~~ IDP1 (DU) TIM ~~ PU PU ~~ IDP0 (DD) ~~ IOM -CH1 IOM -CH2 IOM -CH2 ~~ ~~ ~~ ~~ IDP1 (DU) ~~ ~~ FSC ~~ R R B1 IDP0 (DD) MR MX ~~ ~~ 0.2 to 4 ms R IOM -CH1 R B1 ~~ DCL 132 x DCL R Note : IDP0 is input and IDP1 is low during IOM -CH1 if SQXR : IDC = 1 R IDP0 is low and IDP1 is input during IOM -CH1 if SQXR : IDC = 0 Figure 47 Activation of the IOM(R) Interface (CFS=1, register SQXR) Semiconductor Group 123 ITD05962 Operational Description The ISAC-S TE supplies IOM timing signals as long as there is no DIU command in the C/I (C/ I0) channel. If timing signals are no longer required and activation is not yet requested, this is indicated by programming DIU in the CIX0 register. As an alternative to activation via IDP1 (DU), the IOM interface can be activated by setting the CFS bit to "0". The activation of FSC1 and DCL in this case is similar to figure 47. Note that the IOM interface can be deactivated through DIU (power-down state, figure 46) only if CFS is set to logical "1". 3.3.2 Activation/Deactivation of S/T Interface Assuming the ISAC-S TE has been initialized with the required features of the application, it is now ready to transmit and receive messages in the D channel (LAPD support). But as a prerequisite, the layer 1 has to be activated. The layer-1 functions are controlled by commands issued via the CIXR/CIX0 register. These commands, sent over the IOM C/I channel 0 to layer 1, trigger certain procedures, such as activation/deactivation, switching of test loops and transmission of special pulse patterns. These are governed by layer-1 state diagrams in accordance with CCITT I.430. Responses from layer 1 are obtained by reading the CIRR/CIR0 register after a CISQ interrupt (ISTA). The state diagrams are shown in figure 49. The activation/deactivation implemented by the ISAC-S TE agrees with the requirements set forth in CCITT recommendations. State identifiers F1-F8 (TE) are in accordance with CCITT I.430. In the state diagrams a notation is employed which explicitly specifies the inputs and outputs on the S interface and in the C/I channel: see figure 48. R ISAC -S TE OUT C/ Ind. R ISAC -S TE IN Cmd. State S-INFO iX Unconditional Transition iY ITD05676 Figure 48 Semiconductor Group 124 Operational Description 3.3.2.1 Layer-1 Command/Indication Codes and State Diagrams Table 10 Commands Command (upstream) Abbr. Code Remarks Timing TIM 0000 Activation of all output clocks is requested Reset RS 0001 (x) Send continuous zeros SCZ 0100 Transmission of pseudo-ternary pulses at 96-kHz frequency (x) Send single zeros SSZ 0010 Transmission of pseudo-ternary pulses at 2-kHz frequency (x) Activate request, set priority 8 AR8 1000 Activation command, priority to 8 (see note) set D-channel Activate request, set priority 10 AR10 1001 Activation command, priority to 10 (see note) set D-channel Activate request loop ARL 1010 Activation of test loop 3 (x) Deactivate indication upstream DIU 1111 IOM-interface clocks can be disabled (x) unconditional commands Important Note: When in the activated state (AI8/AI10 indication) the 2B+D channels are only transferred from the IOM-2 to the S/T interface if an "Activate Request" command is written to the CIX0 register. Semiconductor Group 125 Operational Description Table 11 Indications Indication (downstream) Abbr. Code Remarks Power-up PU 0111 IOM clocking is provided Deactivate request DR 0000 Deactivation request by S interface Error indication EI 0110 Either: (pin RST = 1 and bit CFS = 0) or RS Level detected RSY 0100 Signal received, receiver not synchronous Activate request downstream ARD 1000 Info 2 received Test indication TI 1010 Test loop 3 activated or continuous zeros transmitted Awake test indication ATI 1011 Level detected during test loop Activate indication with priority class 8 AI8 1100 Info 4 received, D-channel priority is 8 or 9 Activate indication with priority class 10 AI10 1101 Info 4 received, D-channel priority is 10 or 11 Deactivate indication downstream DID 1111 Clocks will be disabled in TE, quiescent state Semiconductor Group 126 Operational Description F3 Power-Down This is the deactivated state of the physical protocol. The receive line awake unit is active except during an RST pulse. Clocks are disabled if SQXR:CFS=1. The power consumption in this state is approximately 80 mW when the clock is running, and 8 mW otherwise. F3 Power-Up This state is identical to "F3 power-down", except for the C/I-output message. The state is invoked by a C/I command TIM = "0000" (or IDP1 static low). After the subsequent activation of the clocks the PU message is outputted. This occurs 0.5 ms to 4 ms after application of TIM, depending on crystal capacitances. F3 Pending Deactivation The ISAC-S TE reaches this state after receiving INFO0 (from states F5 to F8) for 16 ms (64 frames). This time constant is a "flywheel" to prevent accidental deactivation. From this state an activation is only possible from the line (transition "F3 pend. deact." to "F5 unsynchronized"). A power-down state may be reached only after receiving DIU. F4 Pending Activation Activation has been requested from the terminal, INFO1 is transmitted, INFO0 is still received, "Power-Up" is transmitted in the C/I channel. This state is stable: timer T3 (I.430) is to be implemented in software. F5 Unsynchronized At the reception of any signal from the NT, the ISAC-S TE ceases to transmit INFO1 and awaits identification of INFO2 or INFO4. This state is reached at most 50 s after a signal different from INFO0 is present at the receiver of the ISAC-S TE. F6 Synchronized When the ISAC-S TE receives an activation signal (INFO2), it responds with INFO3 and waits for normal frames (INFO4). This state is reached at most 6 ms after an INFO2 arrives at the ISAC-S TE (when the oscillator was disabled in "F3 power-down"). F7 Activated This is the normal active state with the layer-1 protocol activated in both directions. Note that in IOM-2 mode the 2B+D channels can only be transmitted to the S/T interface if an "Activation Request" command is written to the CIX0 register. From state "F6 synchronized", state F7 is reached at most 0.5 ms after reception of INFO4. From state "F3 power-down" with the oscillator disabled, state F7 is reached at most 6 ms after the ISAC-S TE is directly activated by INFO4. Semiconductor Group 127 Operational Description F8 Lost Framing This is the condition where the ISAC-S TE has lost frame synchronization and is awaiting resynchronization by INFO2 or INFO4 or deactivation by INFO0. Unconditional States Loop 3 Closed On Activate Request Loop command, INFO3 is sent by the line transmitter internally to the line receiver (INFO0 is transmitted to the line). The receiver is not yet synchronized. Loop 3 Activated The receiver is synchronized on INFO3 which is looped back internally from the transmitter. Data may be sent. The indication "TI" or "ATI" is output depending on whether or not a signal different from INFO0 is detected on the S interface. Test Mode Continuous Pulses Continuous alternating pulses are sent. Test Mode Single Pulses Single alternating pulses are sent (2-kHz repetition rate). Reset State A software reset (RS) forces the ISAC-S TE to an idle state where the analog components are disabled (transmission of INFO0) and the S line awake detector is inactive. Thus activation from the NT is not possible. Clocks are still supplied (TE mode) and the outputs are in a low impedance state. The reset state should be left only with a "Deactivation Indication Upstream" (DIU) command before any other command is given. Semiconductor Group 128 Operational Description DID RST DIU TIM F3 Power Down i0 PU ARU i0 DIU ARU i0 DIU TIM F4 Pend. Act. PU TIM DIS F3 Power Up ARU i1 i0 i0 i0 i0 i0 RSYD i4 X F5 Unsynchroniz. i0 i0 i0 i2 X i0 DIU i0 ARD X Uncond. States TIM F6 Synchronized i3 i4 X DR i0 i0 F8 Lost Framing i0 X DIU i0 i2 RSYD i2 ARU TIM F3 Pend. Deact. i0 i0 i0 OUT IN Ind. Cmd. i2 i4 SD ARU AID F7 Activated R IOM -2 i0 State i0 i3 S i4 ix iy X: Unconditional Command can be : ARL, RES,TM, SSP ITD05429 Figure 49a State Diagram Semiconductor Group 129 Operational Description PU ARL TI ARL SCZ Loop 3 Closed i3 1) i3 * SCZ Test Mode Continuous Puls. ic X * X i3 TI ATI ARL RS EI Reset State Loop 3 Activated i0 i3 1) i0 i0 X IOM R OUT IN Ind. Cmd. ix * X SSZ State S RS iy Any Ind. SSZ Test Mode Single Pulses is * X : Only Internally X : Forcing Commands can be : ARL, RES, TM, SSP is : Single Pulses, 4 kHz ic : Test Pulses, 96 kHz 1) ITD02333 Figure 49b State Diagram: Unconditional Transitions Semiconductor Group 130 Operational Description 3.3.3 Example of Activation/Deactivation An example of an activation/deactivation of the S interface, with the time relationships mentioned in the previous chapters, is shown in figure 50, in the case of an ISAC(R)-S TE in TE and an ISAC-S in LT-S Mode. R R ISAC -S TE TE ISAC -S / SBCX LT-S INFO 0 INFO 2 INFO 3 AID AIU 0.5 ms INFO 4 AR max. 2 ms ARD max. 6 ms RSYD 4 ms INFO 1 ARU DR 32 ms INFO 0 16 ms DR 16 ms INFO 0 DIU ITD05426 Figure 50 Example of Activation/Deactivation Semiconductor Group 131 Operational Description 3.4 Control of Layer-2 Data Transfer The control of the data transfer phase is mainly done by commands from the P to ISAC-S TE via the Command Register (CMDR). Table 12 gives a summary of possible interrupts from the HDLC controller and the appropriate reaction to these interrupts. Table 13 lists the most important commands which are issued by a microprocessor by setting one or several bits in CMDR. The powerful FIFO logic, which consists of a 2 x 32 byte receive and 2 x 32 byte transmit FIFO, as well as an intelligent FIFO controller, builds a flexible interface to the upper protocol layers implemented in the microcontroller. The extent of LAPD protocol support is dependent on the selected message transfer mode, see section 2.3.2. Table 12 Interrupts from ISAC(R)-S TE HDLC Controller Mnemonic Register (addr. hex) Meaning Reaction Layer-2 Receive RPF ISTA (20) Receive Pool Full. Request to read received bytes of an uncompleted HDLC frame from RFIFO Read 32 bytes from RFIFO and acknowledge with RMC. RME ISTA (20) Receive Message End. Request to read received bytes of a complete HDLC frame (or the last part of a frame) from RFIFO. Read RFIFO (number of bytes given by RBCL4-0) and status information and acknowledge with RMC. RFO EXIR (24) Receive Frame Overflow. A complete frame has been lost because storage space in RFIFO was not available. Error report for statistical purposes. Possible cause: deficiency in software. PCE EXIR (24) Protocol Error. S- or I frame with Link re-establishment. incorrect N(R) or S frame with Indication to layer 3. I field received (in auto-mode only) or an I frame which is not a command or S frame with an undefined control field. Semiconductor Group 132 Operational Description Table 12 (cont'd) Mnemonic Register (addr. hex) Meaning Reaction Layer-2 Transmit XPR ISTA (20) XMR EXIR (24) Transmit Message Repeat. Transmission of the frame must Frame must be repeated be repeated. No indication to because of a transmission error layer 3. (all HDLC message transfer modes) or a received negative acknowledgement (auto mode only) from peer station. XDU EXIR (24) Transmit Data Underrun. Frame has been aborted because the XFIFO holds no further data and XME (XIFC or XTFC) was not issued. RSC ISTA (20) Receive Status Change. Stop sending new I frames. A status change from peer station has been received (RR or RNR frame), auto-mode only. TIN ISTA (20) Timer Interrupt. External timer Link re-establishment. expired or, in auto-mode, Indication to layer 3. (autointernal timer (T200) and repeat mode) counter (N200) both expired. Semiconductor Group Transmit Pool Ready. Further octets of an HDLC frame can be written to XFIFO. If XIFC was issued (auto mode), indicates that the message was successfully acknowledged with S frame. 133 Write data bytes in the XFIFO if the frame currently being transmitted is not finished or a new frame is to be transmitted, and issue an XIF, XIFC, XTF or XTFC command. In auto mode applications read the information in chapter 2.4.5.2. Transmission of the frame must be repeated. Possible cause: excessive software reaction times. Operational Description Table 13 List of Commands (CMDR (21) Register) Command Mnemonic HEX Bit 7...0 RMC 80 1000 0000 Receive Message Complete. Acknowledges a block (RPF) or a frame (RME) stored in the RFIFO. RRES 40 0100 0000 Reset HDLC Receiver. The RFIFO is cleared. The transmit and receive counters (V(S), V(R)) are reset (auto-mode). RNR 20 0010 0000 Receiver Not Ready (auto-mode). An I- or S frame will be acknowledged with RNR frame. STI 10 0001 0000 Start Timer. XTFC (XTF+XME) 0A 0000 1010 Transmit Transparent Frame and Close. Enables the "transparent" transmission of the block entered last in the XFIFO. The frame is closed with a CRC and a flag. XIFC (XIF+XME) 06 0000 0110 Transmit I frame and Close. Enables the "auto-mode" transmission of the block entered last in the XFIFO. The frame is closed with a CRC and a flag. XTF 08 0000 1000 Transmit Transparent Frame. Enables the "transparent" transmission of the block entered last in the XFIFO without closing the frame. XIF 04 0000 0100 Transmit I frame. Enables the "auto-mode" transmission of the block entered last in the XFIFO without closing the frame. XRES 01 0000 0001 Reset HDLC Transmitter. The XFIFO is cleared. A frame currently in transmission will be aborted and closed by an abort sequence (7 "1"). Semiconductor Group Meaning 134 Operational Description 3.4.1 HDLC-Frame Reception Assuming a normally running communication link (layer-1 activated, layer-2 link established, TEI assigned), figure 51 illustrates the transfer of an I frame via the D channel. The transmitter is shown on the left and the receiver on the right, with the interaction between the microcontroller system and the ISAC-S TE in terms of interrupt and command stimuli. When the frame (excluding the CRC field) is not longer than 32 bytes, the whole frame is transferred in one block. The reception of the frame is reported via the Receive Message End (RME) interrupt. The number of bytes stored in RFIFO can be read out from RBCL. The Receive Status Register (RSTA) includes information about the frame, such as frame aborted yes/no or CRC valid yes/no and, if complete or partial address recognition is selected, the identification of the frame address. Depending on the HDLC-message transfer mode, the address and control field of the frame can be read from auxiliary registers (SAPR and RHCR), as shown in figure 52. LAPD Link RPF XIF/XTF XPR R ISAC -S (LT-S) R XIF/XTF me ISAC -S TE (TE) I-Fra CSystem XPR RMC RPF CSystem RMC XIFC/XTF C nsparent XPR (Tra mit) Trans ame S-Fr )*) (RR M - ode XPR (Automit) Trans RME RMC ITD05677 : = Data Transfer *) In Auto Mode the "RR" Response will be Transmitted Autonomously Figure 51 Transmission of an I Frame in the D Channel (Subscriber to Exchange) Semiconductor Group 135 Operational Description Flag Auto-Mode (U-and -Frames) - Non-Auto Mode Transparent Mode 1 Address High Address Low Control Information CRC SAP1,SAP2 FE,FC TEI1,TEI2 FF RHCR RFIFO RSTA (Note 1) (Note 2) (Note 3) SAP1,SAP2 FE,FC TEI1,TEI2 FF RHCR RFIFO RSTA (Note 1) (Note 2) (Note 4) SAPR TEI1,TEI2 FF RHCR RFIFO RSTA Flag (Note 4) Transparent Mode 2 SAP1,SAP2 FE,FC Transparent Mode 3 RFIFO RSTA RFIFO RSTA Description of Symbols: ITD05674 R Checked automatically by ISAC -S TE Compared with Register or Fixed Value Stored Info Register or RFIFO Figure 52 Receive Data Flow Note 1 Only if a 2-byte address field is defined (MDS0 = 1 in MODE register). Note 2 Comparison with Group TEI (FFH) is only made if a 2-byte address field is defined (MDS0 = 1 in MODE register). Note 3 In the case of an extended, modulo 128 control field format (MCS = 1 in SAP2 register) the control field is stored in RHCR in compressed form (I frames). Note 4 In the case of an extended control field, only the first byte is stored in RHCR, the second in RFIFO. A frame longer than 32 bytes is transferred to the microcontroller in blocks of 32 bytes plus one remainder block of length 1 to 32 bytes. The reception of a 32-byte block is reported by a Receive Pool Full (RPF) interrupt and the data in RFIFO remains valid until this interrupt is acknowledged (RMC). This process is repeated until the reception of the remainder block is completed, as reported by RME (figure 51). When the total frame length exceeds 4095 bytes, bit OV (RBCH) is set but the counter is not blocked. If the second RFIFO pool has been filled or an end-of-frame is received while a previous RPF or RME interrupt is not yet acknowledged by RMC, the corresponding interrupt will be generated only when RMC has been issued. When Semiconductor Group 136 Operational Description RME has been indicated, bits 0-4 of the RBCL register represent the number of bytes stored in the RFIFO. Bits 7-5 of RBCL and bits 0 to 3 of RBCH indicate the total number of 32-byte blocks which where stored until the reception of the remainder block. The contents of RBCL, RBCH and RSTA registers are valid only after the occurrence of the RME interrupt, and remain valid until the microprocessor issues an acknowledgement (RMC). The contents of RHCR and/or SAPR, also remain valid until acknowledgement. If a frame could not be stored due to a full RFIFO, the microcontroller is informed of this via the Receive Frame Overflow interrupt (RFO). 3.4.2 HDLC-Frame Transmission After the XFIFO status has been checked by polling the Transmit FIFO Write Enable (XFW) bit or after a Transmit Pool Ready (XPR) interrupt, up to 32 bytes may be entered in XFIFO. Transmission of an HDLC frame is started when a transmit command (see table 13) is issued. The opening flag is generated automatically. In the case of an auto-mode transmission (XIF or XIFC), the control field is also generated by the ISAC-S TE, and the contents of register XAD1 (and, for LAPD, XAD2) are transmitted as the address, as shown in figure 53. HDLC Frame Flag Address Control Information CRC Flag Transmit I-Frame (XIF) Auto Mode,8 - Bit Addr. Flag XAD1 Control XFIFO CRC Flag Transmit I-Frame (XIF) Auto -Mode, 16 - Bit Addr. Flag Control XFIFO CRC Flag Transmit Transparent Frame (XTF) All Modes Flag CRC Flag XAD1 XAD2 XFIFO ITD05667 Note: Length of Control Field is b or 16 Bit Description of Symbols: R Generated automatically by ISAC -S TE Written initially by CPU (Info Register) R Loaded (repeatedly) by CPU upon ISAC -S TE request (XPR Interrupt) Figure 53 Transmit Data Flow Semiconductor Group 137 Operational Description The HDLC controller will request another data block by an XPR interrupt if there are no more than 32 bytes in XFIFO and the frame close command bit (Transmit Message End XME) has not been set. To this the microcontroller responds by writing another pool of data and reissuing a transmit command for that pool. When XME is set, all remaining bytes in XFIFO are transmitted, the CRC field and the closing flag of the HDLC frame are appended and the controller generates a new XPR interrupt. The microcontroller does not necessarily have to transfer a frame in blocks of 32 bytes. As a matter of fact, the sub-blocks issued by the microcontroller and separated by a transmit command, can be between 0 and 32 bytes long. If the XFIFO runs out of data and the XME command bit has not been set, the frame will be terminated with an abort sequence (seven 1's) followed by inter-frame time fill, and the microcontroller will be advised by a Transmit Data Underrun (XDU) interrupt. An HDLC frame may also be aborted by setting the Transmitter Reset (XRES) command bit. 3.5 Reset After a hardware reset (pin RST), layer 1 will have reached the following state: - F3 standby according to CCITT I.430. F3 standby state means that the internal oscillator, the DCL clock and FSC1 are active. During the reset pulse pin SDS1 is "low", all other pins are in high impedance state. The S/T interface awake detector is active after reset. The F3 power down state, where the internal oscillator itself is disabled, can be reached by setting the CFS bit (SQXR register) to logical "1". A subset of ISAC-S TE registers with defined reset values is listed in table 14. Table 14 State of ISAC(R)-S TE Registers after Hardware Reset Register (address (hex)) Value after Reset (hex) Meaning ISTA (20) 00 No interrupts MASK (20) 00 All interrupts enabled EXIR (24) 00 No interrupts STAR (21) 48 (4A) - XFIFO is ready to be written to - RFIFO is ready to receive at least 16 octets of a new message CMDR (21) 00 No command Semiconductor Group 138 Operational Description Table 14 (cont'd) Register (address (hex)) Value after Reset (hex) Meaning MODE (22) 00 - auto-mode - 1-octet address field - external timer mode - receiver inactive RBCL RBCH (25) (2A) 00 XXX000002 - no frame bytes received SPCR (30) 00 - IDP1 pin = "High" - Timing mode 0 - IOM interface test loop deactivated - SDS1 pin = "Low" CIR0 (31) 7C - no change in S/Q channel - another device occupies the D and C/I channels - received C/I code = "1111" - no C/I code change CIX0 (31) 3C - TIC bus is not requested for transmitting a C/I code - transmitted C/I code = "1111" STCR (37) 00 - terminal specific functions disabled - TIC-bus address = "0000" - no synchronous transfer ADF1 (38) 00 - no test mode - active clock signals (standby) in TE mode - no prefilter - inter-frame time fill = continuous "1" ADF2 (39) 00 - IOM-1 interface mode selected - SDS1 low SQXR (3B) 0F/00 - S, Q interrupt not enabled Semiconductor Group 139 Operational Description 3.6 Initialization During initialization a subset of registers have to be programmed to set the configuration parameters according to the application and desired features. They are listed in table 15. After reset, the ISAC-S TE is in IOM-1 mode. As a result, the fist microcontroller operation has to be an access to ADF2 to program IOM-2 interface mode. Table 15 Application Register (address) Bit Effect ADF2 IMS Program IOM-2 interface mode D1C2-0 ODS Polarity of SDS1 IOM-output driver tristate/open drain SPU Set the ISAC-S TE in standby by requesting clocks (if CFS = 1, register SQXR) TLP IOM-interface test loop C2C1-0 C1C1-0 B-channel switching or B/IC channel connect IDC IOM-Data Port IDP0,1 direction control (must be set to "0" for normal operation) CFS 0 Permanent standby 1 Power-down state enabled TEM Test Mode Tests with layer 1 disabled PFS Prefilter enable TE IOF IOM OFF/ON RSS Hardware reset generated by either subscriber/ exchange awake or watchdog timer SPCR (Note) SQXR ADF1 CIX0 (39H) (30H) (3BH) (38H) (31H) Semiconductor Group 140 Restricted to IOM-2 TE specific functions (TSF = 1) Operational Description Table 15 (cont'd) Register (address) Bit Effect STCR TSF Terminal specific function enable TBA2-0 TIC-bus address MDS2-0 HDLC-message transfer mode 2 bytes/1 byte address TMD Timer mode external/internal DIM2-0 Point-to-point/TIC-bus configuration on IOM interface, for D + C/I channel arbitration Point-to-point/bus configuration on S/T interface, for D-channel access. CNT VALUE N1 and T1 in internal timer mode (TMD = 1) T2 in external timer mode MODE (37H) (22H) Application TIMR (23H) XAD1 XAD2 (24H) (25H) SAPI, TEI Transmit frame address SAP1/2 TEI1/2 (26H/27H) (28H/29H) Receive SAPI, TEI address values for internal address recognition Restricted to Bus configuration for D + C/I (TIC) Auto-mode only Auto-mode only Note: After a hardware reset the pin SDS1 is "low", until the SPCR is written to for the first time. From that moment on, the function taken on by these pins depends on the state of the IOM Mode Select bit IMS (ADF2 register). Semiconductor Group 141 Register Description 4 Detailed Register Description The parameterization of the ISAC-S TE and the transfer of data and control information between the P and ISAC-S TE is performed through two register sets. The register set in the address range 00-2BH pertains to the HDLC transceiver and LAPD controller. It includes the two FIFOs having an identical address range from 00-1FH. The register set ranging from 30-3BH pertains to the control of layer-1 functions and of the IOM interface. The address map and a register summary are shown in the following tables: Table 16 ISAC(R)-S TE Address Map 00-2BH Address (hex) Read Write Name Description Name Description RFIFO Receive FIFO XFIFO Transmit FIFO 20 ISTA Interrupt Status Register MASK Mask Register 21 STAR Status Register CMDR Command Register 22 MODE Mode Register 23 TIMR Timer Register 24 EXIR Extended Interrupt Register XAD1 Transmit Address 1 25 RBCL Receive Frame Byte Count Low XAD2 Transmit Address 2 26 SAPR Received SAPI SAP1 Individual SAPI 1 27 RSTA Receive Status Register SAP2 Individual SAPI 2 TEI1 Individual TEI 1 TEI2 Individual TEI 2 00 . . 1F 28 29 RHCR Receive HDLC Control 2A RBCH Receive Frame Byte Count High 2B STAR2 Status Register 2 Semiconductor Group 142 Register Description Table 17 ISAC(R)-S TE Address Map 30-3BH Address (hex) Read Write Name Description Name Description 30 SPCR Serial Port Control Register 31 CIR0 Command/Indication Receive 0 CIX0 Command/Indication Transmit 0 32 MOR0 MONITOR Receive 0 MOX0 MONITOR Transmit 0 33 CIR1 Command/Indication Receive 1 CIX1 Command/Indication Transmit 1 34 MOR1 MONITOR Receive 1 MOX1 MONITOR Transmit 1 35 C1R Channel Register 1 36 C2R Channel Register 2 37 B1CR B1-Channel Register STCR Sync Transfer Control Register 38 B2CR B2-Channel Register ADF1 Additional Feature Register 1 39 ADF2 Additional Feature Register 2 3A MOSR MONITOR Status Register MOCR MONITOR Control Register 3B SQRR S-, Q-Channel Receive Register SQXR S-, Q-Channel Transmit Register Semiconductor Group 143 Register Description Table 18 Register Summary: HDLC Operation and Status Registers 7 0 20H RME RPF RSC XPR TIN CISQ SIN EXI ISTA R 20H RME RPF RSC XPR TIN CISQ SIN EXI MASK W 21H XDOV XFW MBR MAC1 X MAC0 STAR R 21H RMC RRES RNR STI XTF XIF XME XRES CMDR W 22H MDS2 MDS1 MDS0 TMD RAC DIM2 DIM1 DIM0 MODE R/W 23H XRNR RRNR TIMR R/W EXIR R XAD1 W RBCL R 25H XAD2 W 26H SAPR R 24H CNT XMR XDU VALUE PCE RFO SOV MOS SAW WOV 24H 25H RBC7 RBC6 RBC5 26H 27H RBC4 RBC3 RBC2 SAPI1 RDA RDO CRC 27H RAB SA1 SA0 SAPI2 28H RBC1 RBC0 CRI 0 SAP1 W C/R TA RSTA R MCS 0 SAP2 W EA TEI1 W TEI1 29H RHCR R 29H EA TEI2 TEI2 W R 2AH XAC VN1 VN0 OV RBC1 RBC1 RBC9 RBC8 RBCH 2BH 0 0 0 0 WFA MULT TREC SDET STAR2 R 2BH 0 0 0 0 0 MULT 0 0 STAR2 W Semiconductor Group 144 Register Description Table 19 Register Summary: Special Purpose Register IOM(R)-2 Mode IOM(R)-2: 7 0 30H SPU 0 31H SQC BAS 31H RSS BAC 0 TLP C1C1 C1C0 C2C1 C2C0 SPCR R/W CODR0 CIC0 CIC1 CIR0 R CODX0 1 1 CIX0 W 32H MOR0 R 32H MOX0 W 33H CODR1 MR1 MX1 CIR1 R 33H CODX1 1 1 CIX1 W 34H MOR1 R 34H MOX1 W 35H C1R R/W 36H C2R R/W 37H B1CR R STCR W B2CR R 37H TSF TBA2 TBA1 TBA0 ST1 ST0 SC1 SC0 38H 38H WTC1 WTC2 TEM PFS IOF 0 0 ITF ADF1 W 39H IMS 0 0 0 ODS D1C2 D1C1 D1C0 ADF2 R/W 3AH MDR1 MER1 MDA1 MAB1 MDR0 MER0 MDA0 MAB0 MOSR R 3AH MRE1 MRC1 MXE1 MXC1 MRE0 MRC0 MXE0 MXC0 MOCR W 3BH IDC CFS CI1E SYN SQR1 SQR2 SQR3 SQR4 SQRR R 3BH IDC CFS CI1E SQIE SQX1 SQX2 SQX3 SQX4 SQXR W Semiconductor Group 145 Register Description 4.1 HDLC Operation and Status Registers 4.1.1 Receive FIFO RFIFO Read Address 00-1FH A read access to any address within the range 00-1FH gives access to the "current" FIFO location selected by an internal pointer which is automatically incremented after each read access. This allows for the use of efficient 'move string' type commands by the processor. The RFIFO contains up to 32 bytes of received frame. After an ISTA:RPF interrupt, exactly 32 bytes are available. After an ISTA:RME interrupt, the number of bytes available can be obtained by reading the RBCL register. 4.1.2 Transmit FIFO XFIFO Write Address 00-1FH A write access to any address within the range 00-1FH gives access to the "current" FIFO location selected by an internal pointer which is automatically incremented after each write access. This allows for the use of efficient 'move string' type commands by the processor. Up to 32 bytes of transmit data can be written into the XFIFO following an ISTA:XPR interrupt. 4.1.3 Interrupt Status Register ISTA Read Address 20H Value after reset: 00H 7 0 RME RME RPF RSC XPR TIN CISQ SIN EXI Receive Message End One complete frame of length less than or equal to 32 bytes, or the last part of a frame of length greater than 32 bytes has been received. The contents are available in the RFIFO. The message length and additional information may be obtained from RBCH + RBCL and the RSTA register. RPF Receive Pool Full A 32-byte block of a frame longer than 32 bytes has been received and is available in the RFIFO. The frame is not yet complete. RSC Receive Status Change. Used in auto-mode only. A status change in the receiver of the remote station - Receiver Ready/Receiver Not Ready - has been detected (RR or RNR S frame). The actual status of the remote station can be read from the STAR register (RRNR bit). Semiconductor Group 146 Register Description XPR Transmit Pool Ready A data block of up to 32 bytes can be written to the XFIFO. An XPR interrupt will be generated in the following cases: - after an XTF or XIF command, when one transmit pool is emptied and the frame is not yet complete - after an XTF together with an XME command is issued, when the whole transparent frame has been transmitted - after an XIF together with an XME command is issued, when the whole I frame has been transmitted and a positive acknowledgement from the remote station has been received, (auto-mode). TIN Timer Interrupt The internal timer and repeat counter has expired (see TIMR register). CISQ C/I- or S/Q-Channel Change A change in C/I channel 0, C/I channel 1 (only in IOM-2 TE mode) or S/Q channel has been recognized. The actual value can be read from CIR0, CIR1 or SQRR. SIN Synchronous Transfer Interrupt When programmed (STCR register), this interrupt is generated to enable the processor to lock on to the IOM timing, for synchronous transfers. EXI Extended Interrupt This bit indicates that one of six non-critical interrupts has been generated. The exact interrupt cause can be read from EXIR. Note: A read of the ISTA register clears all bits except EXI and CISQ. EXI is cleared by reading the EXIR register, CISQ is cleared by reading CIRR/CIR0. 4.1.4 Mask Register MASK Write Address 20H Value after reset: 00H 7 0 RME RPF RSC XPR TIN CISQ SIN EXI Each interrupt source in the ISTA register can be selectively masked by setting to "1" the corresponding bit in MASK. Masked interrupt status bits are not indicated when ISTA is read. Instead, they remain internally stored and pending, until the mask bit is reset to zero. Note: In the event of an extended interrupt and of a C/I- or S/Q-channel change, EXI and CISQ are set in ISTA even if the corresponding mask bits in MASK are active, but no interrupt (INT pin) is generated. Semiconductor Group 147 Register Description 4.1.5 Status Register STAR Read Address 21H Value after reset: 48H or 4A H 7 XDOV XDOV 0 XFW XRNR RRNR MBR MAC1 X MAC0 Transmit Data Overflow More than 32 bytes have been written in one pool of the XFIFO, i.e. data has been overwritten. XFW Transmit FIFO Write Enable Data can be written in the XFIFO. This bit may be polled instead of (or in addition to) using the XPR interrupt. XRNR Transmit RNR. Used in auto-mode only In auto-mode, this bit indicates whether the ISAC-S TE receiver is in the "ready" (0) or "not ready" (1) state. When "not ready", the ISAC-S TE sends an RNR S frame autonomously to the remote station when an I frame or an S frame is received. RRNR Receive RNR. Used in auto-mode only In the auto-mode, this bit indicates whether the ISAC-S TE has received an RR or an RNR frame, this being an indication of the current state of the remote station: receiver ready (0) or receiver not ready (1). MBR Message Buffer Ready This bit signifies that temporary storage is available in the RFIFO to receive at least the first 16 bytes of a new message. MAC1 MONITOR Transmit Channel 1 Active (IOM-2 terminal mode only) Data transmission is in progress in MONITOR channel 1. MAC0 MONITOR Transmit Channel 0 Active. Used in IOM-2 mode only. Data transmission is in progress in MONITOR channel 0. Note: Bit 1 may toggle dependend the time of access. Semiconductor Group 148 Register Description 4.1.6 Command Register CMDR Write Address 21H Value after reset: 00H 7 0 RMC RRES RNR STI XTF XIF XME XRES Note: The maximum time between writing to the CMDR register and the execution of the command is 2.5 DCL-clock cycles. During this time no further commands should be written to the CMDR register to avoid any loss of commands. RMC Receive Message Complete Reaction to RPF (Receive Pool Full) or RME (Receive Message End) interrupt. By setting this bit, the processor confirms that it has fetched the data, and indicates that the corresponding space in the RFIFO may be released. RRES Receiver Reset HDLC receiver is reset, the RFIFO is cleared of any data. In addition, in auto-mode, the transmit and receive counters (V(S), V(R)) are reset RNR Receiver Not Ready Used in auto-mode only. Determines the state of the ISAC-S TE HDLC receiver. When RNR = "0", a received I or S-frame is acknowledged by an RR supervisory frame, otherwise by an RNR supervisory frame. STI Start Timer The ISAC-S TE hardware timer is started when STI is set to one. In the internal timer mode (TMD bit, MODE register) an S command (RR, RNR) with poll bit set is transmitted in addition. The timer may be stopped by a write of the TIMR register. XTF Transmit Transparent Frame After having written up to 32 bytes in the XFIFO, the processor initiates the transmission of a transparent frame by setting this bit to "1". The opening flag is automatically added to the message by the ISAC-S TE. XIF Transmit I Frame Used in auto-mode only After having written up to 32 bytes in the XFIFO, the processor initiates the transmission of an I frame by setting this bit to "1". The opening flag, the address and the control field are automatically added by the ISAC-S TE. Semiconductor Group 149 Register Description XME Transmit Message End By setting this bit to "1" the processor indicates that the data block written last in the XFIFO completes the corresponding frame. The ISAC-S TE terminates the transmission by appending the CRC and the closing flag sequence to the data. XRES Transmitter Reset HDLC transmitter is reset and the XFIFO is cleared of any data. This command can be used by the processor to abort a frame currently in transmission. Notes: After an XPR interrupt further data has to be written in the XFIFO and the appropriate Transmit Command (XTF or XIF) has to be written in the CMDR register again to continue transmission, when the current frame is not yet complete (see also XPR in ISTA). 4.1.7 During frame transmission, the 0-bit insertion according to the HDLC bit-stuffing mechanism is done automatically. Mode Register MODE Read/Write Address 22H Value after reset: 00H 7 0 MDS2 MDS1 MDS0 TMD RAC DIM2 DIM1 DIM0 MDS2-0 Mode Select Determines the message transfer mode of the HDLC controller, as follows: Semiconductor Group 150 Register Description MDS2 MDS1 MDS0 Mode Number Address Comparison of 1. Byte 2. Byte Address Bytes Remark 0 0 0 Auto-mode 1 TEI1, TEI2 - One-byte address compare. HDLC-protocol handling for frames with address TEI1 0 0 1 Auto-mode 2 SAP1, SAP2, SAPG TEI1, TEI2, TEIG Two-byte address compare. LAPD-protocol handling for frames with address SAP1 + TEI1 0 1 0 Non-auto 1 TEI1, TEI2 - One-byte address compare. 2 SAP1, SAP2, SAPG TEI1, TEI2, TEIG Two-byte address compare. >1 - TEI1, TEI2, TEIG Low-byte address compare. - - - No address compare. All frames accepted. >1 SAP1, SAP2, SAPG - High-byte address compare. mode 0 1 1 Non-auto mode 1 0 0 Reserved 1 0 1 Transparent mode 1 1 1 0 Transparent mode 2 1 1 1 Transparent mode 3 Note: SAP1, SAP2: two programmable address values for the first received address byte (in the case of an address field longer than 1 byte); SAPG = fixed value FC/FEH. TEI1, TEI2: two programmable address values for the second (or the only, in the case of a one-byte address) received address byte; TEIG = fixed value FFH. TMD Timer Mode Sets the operating mode of the ISAC-S TE timer. In the external mode (0) the timer is controlled by the processor. It is started by setting the STI bit in CMDR and it is stopped by a write of the TIMR register. In the internal mode (1) the timer is used internally by ISAC-S TE for timeout and retry conditions (handling of LAPD/HDLC protocol in auto-mode). RAC Receiver Active The HDLC receiver is activated when this bit is set to "1". DIM2-0 Digital Interface Mode These bits define the characteristics of the IOM-Data Ports (IDP0, IDP1) according to following tables: Semiconductor Group 151 Register Description IOM(R)-2 Modes (ADF2:IMS = 1) DIM2-0 Characteristics 000 001 010 011 IOM-2 terminal mode SPCR:SPM = 0 x x x x Last octet of IOM channel 2 used for TIC-bus access x x x x Stop/go bit evaluated for D-channel access handling 100-111 x Reserved Applications 4.1.8 x x TE mode Timer Register TIMR Value after reset: undefined (previous value) 7 0 CNT CNT Read/Write Address 23H VALUE The meaning depends on the selected timer mode (TMD bit, MODE register). * internal Timer Mode (TMD = 1) CNT indicates the maximum number of S commands "N1" which are transmitted autonomously by the ISAC-S TE after expiration of time period T1 (retry, according to HDLC). Semiconductor Group 152 Register Description The internal timer procedure will be started in auto-mode: - after start of an I-frame transmission or - after an "RNR" S frame has been received. After the last retry, a timer interrupt (TIN bit in ISTA) is generated. The timer procedure will be stopped when - a TIN interrupt is generated. The time between the start of an I-frame transmission or reception of an "RNR" S frame and the generation of a TIN interrupt is equal to: (CNT+1) x T1. - or the TIMR is written - or a positive or negative acknowledgement has been received. Note: The maximum value of CNT can be 6. If CNT is set to 7, the number of retries is unlimited. * External Timer Mode (TMD = 0) CNT together with VALUE determine the time period T2 after which a TIN interrupt will be generated: CNT x 2.048 s + T1 with T1 = (VALUE + 1) x 0.064 s, in the normal case, and T2 = 16348 x CNT x DCL + T1 with T1 = 512 x (VALUE + 1) x DCL when TLP = 1 (test loop activated, SPCR register). DCL denotes the period of the DCL clock. The timer can be started by setting the STI bit in CMDR and will be stopped when a TIN interrupt is generated or the TIMR register is written. Note: If CNT is set to 7, a TIN interrupt is indefinitely generated after every expiration of T1. VALUE Determines the Time Period T1: T1 = (VALUE + 1) x 0.064 s (SPCR:TLP = 0, normal mode) T1 = 512 x (VALUE + 1) x DCL (SPCR:TLP = 1, test mode). Semiconductor Group 153 Register Description 4.1.9 Extended Interrupt Register EXIR Read Address 24H Value after reset: 00H 7 0 XMR XMR XDU PCE RFO SOV MOS SAW WOV Transmit Message Repeat The transmission of the last frame has to be repeated because: - the ISAC-S TE has received a negative acknowledgement to an I frame in automode (according to HDLC/LAPD) - or a collision on the S bus has been detected after the 32nd data byte of a transmit frame. XDU Transmit Data Underrun The current transmission of a frame is aborted by transmitting seven "1's" because the XFIFO holds no further data. This interrupt occurs whenever the processor has failed to respond to an XPR interrupt (ISTA register) quickly enough, after having initiated a transmission and the message to be transmitted is not yet complete. Note: When an XMR or and XDU interrupt is generated, it is not possible to send transparent frames or I frames until the interrupt has been acknowledged by reading EXIR. PCE Protocol Error Used in auto-mode only. A protocol error has been detected in auto-mode due to a received - S- or I frame with an incorrect sequence number N(R) or - S frame containing an I field. - I frame which is not a command. - S frame with an undefined control field. RFO Receive Frame Overflow The received data of a frame could not be stored, because the RFIFO is occupied. The whole message is lost. This interrupt can be used for statistical purposes and indicates that the processor does not respond quickly enough to an RPF or RME interrupt (ISTA). SOV Synchronous Transfer Overflow The synchronous transfer programmed in STCR has not been acknowledged in time via the SC0/SC1 bit. MOS MONITOR Status A change in the MONITOR Status Register (MOSR) has occured. Semiconductor Group 154 Register Description SAW Subscriber Awake Used only if terminal specific functions are enabled (STCR:TSF = 1). Indicates that a falling edge on the EAW line has been detected, in case the terminal specific functions are enabled (TSF bit in STCR). WOV Watchdog Timer Overflow Used only if terminal specific functions are enabled (STCR:TSF = 1). Signals the expiration of the watchdog timer, which means that the processor has failed to set the watchdog timer control bits WTC1 and WTC2 (ADF1 register) in the correct manner. A reset pulse has been generated by the ISAC-S TE. 4.1.10 Transmit Address 1 XAD1 Write Address 24H 7 0 Used in auto-mode only. XAD1 contains a programmable address byte which is appended automatically to the frame by the ISAC-S TE in auto-mode. Depending on the selected address mode XAD1 is interpreted as follows: * 2-Byte Address Field XAD1 is the high byte (SAPI in the ISDN) of the 2-byte address field. Bit 1 is interpreted as the command/response bit "C/R". It is automatically generated by the ISAC-S TE following the rules of ISDN LAPD protocol and the CRI bit value in SAP1 register. Bit 1 has to be set to "0". C/R Bit Command Response Transmitting End CRI Bit 0 1 subscriber 0 1 0 network 1 In the ISDN LAPD the address field extension bit "EA", i.e. bit 0 of XAD1 has to be set to "0". * 1-Byte Address Field According to the X.25 LAPB protocol, XAD1 is the address of a command frame. Note: In standard ISDN applications only 2-byte address fields are used. Semiconductor Group 155 Register Description 4.1.11 Receive Frame Byte Count Low RBCL Read Address 25H Value after reset: 00H 7 0 RBC7 RBC6 RBC5 RBC4 RBC3 RBC2 RBC1 RBC0 RBC7-0 Receive Byte Count Eight least significant bits of the total number of bytes in a received message. Bits RBC4-0 indicate the length of the data block currently available in the RFIFO, the other bits (together with RBCH) indicate the number of whole 32-byte blocks received. If exactly 32 bytes are received RBCL holds the value 20H. 4.1.12 Transmit Address 2 XAD2 Write 7 Address 25H 0 Used in auto-mode only. XAD2 contains the second programmable address byte, whose function depends on the selected address mode: * 2-Byte Address Field XAD2 is the low byte (TEI in the ISDN) of the 2-byte address field. * 1-Byte Address Field According to the X.25 LAPB protocol, XAD2 is the address of a response frame. Note: See note to XAD1 register description. 4.1.13 Received SAPI Register SAPR 7 Read Address 26H 0 When transparent mode 1 is selected, SAPR contains the value of the first address byte of a receive frame. Semiconductor Group 156 Register Description 4.1.14 SAPI1 Register SAP1 Write Address 26H 7 0 SAPI1 SAPI1 CRI 0 SAPI1 Value Value of the first programmable Service Access Point Identifier (SAPI) according to the ISDN LAPD protocol. CRI Command/Response Interpretation CRI defines the end of the ISDN user-network interface the ISAC-S TE is used on, for the correct identification of "Command" and "Response" frames. Depending on the value of CRI the C/R bit will be interpreted by the ISAC-S, when receiving frames in auto-mode, as follows: C/R Bit CRI Bit Receiving End Command Response 0 subscriber 1 0 1 network 0 1 For transmitting frames in auto-mode, the C/R-bit manipulation will also be done automatically, depending on the value of the CRI bit (refer to XAD1-register description). In message transfer modes with SAPI address recognition the first received address byte is compared with the programmable values in SAP1, SAP2 and the fixed group SAPI. In 1-byte address mode, the CRI bit is to be set to "0". 4.1.15 Receive Status Register RSTA Read Address 27H Value after reset: undefined 7 RDA RDA RDO 0 CRC RAB SA1 SA0 C/R TA Receive Data A "1" indicates that data is available in the RFIFO. After an RME interrupt, a "0" in this bit means that data is available in the internal registers RHCR or SAPR only (e.g. S frame). See also RHCR-register description table. RDO Receive Data Overflow At least one byte of the frame has been lost, because it could not be stored in RFIFO (1). Semiconductor Group 157 Register Description CRC CRC Check The CRC is correct (1) or incorrect (0). RAB Receive Message Aborted The receive message was aborted by the remote station (1), i.e. a sequence of 7 1's was detected. SA1-0 SAPI Address Identification TA TEI Address Identification SA1-0 are significant in auto-mode and non-auto mode with a two-byte address field, as well as in transparent mode 3. TA is significant in all modes except in transparent modes 2 and 3. Two programmable SAPI values (SAP1, SAP2) plus a fixed group SAPI (SAPG of value FC/FEH), and two programmable TEI values (TEI1, TEI2) plus a fixed group TEI (TEIG of value FFH), are available for address comparison. The result of the address comparison is given by SA1-0 and TA, as follows Address Match with Number of address bytes = 1 Number of address bytes = 2 SA1 SA0 TA 1st Byte 2nd Byte x x x x 0 1 TEI2 TEI1 - - 0 0 0 0 1 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 x SAP2 SAP2 SAPG SAPG SAP1 SAP1 TEIG TEI2 TEIG TEI1 or TEI2 TEIG TEI1 reserved Notes: If the SAPI values programmed to SAP1 and SAP2 are identical the reception of a frame with SAP2/TEI2 results in the indication SA1 = 1, SA0 = 0, TA = 1. Normally RSTA should be read by the processor after an RME interrupt in order to determine the status of the received frame. The contents of RSTA are valid only after an RME interrupt, and remain so until the frame is acknowledged via the RMC bit. Semiconductor Group 158 Register Description C/R Command/Response The C/R bit identifies a receive frame as either a command or a response, according to the LAPD rules: 4.1.16 Command Response Direction 0 1 Subscriber to network 1 0 Network to subscriber SAPI2 Register SAP2 Write Address 27H 7 0 SAPI2 SAPI2 MCS 0 SAPI2 Value Value of the second programmable Service Access Point Identifier (SAPI) according to the ISDN LAPD protocol. MCS Modulo Count Select Used in auto-mode only. This bit determines the HDLC-control field format as follows: 0: One-byte control field (modulo 8) 1: Two-byte control field (modulo 128) 4.1.17 TEI1 Register 1 TEI1 Write Address 28H 7 0 TEI1 EA EA Address Field Extension Bit This bit has to be set "1" according to HDLC/LAPD. In all message transfer modes except in transparent modes 2 and 3, TEI1 is used by the ISAC-S for address recognition. In the case of a two-byte address field, it contains the value of the first programmable Terminal Endpoint Identifier according to the ISDN LAPD protocol. In the auto-mode with a two-byte address field, numbered frames with the address SAPI1-TEI1 are handled autonomously by the ISAC-S TE according to the LAPD protocol. Semiconductor Group 159 Register Description Note: If the value FFH is programmed in TEI1, received numbered frames with address SAPI1-TEI1 (SAPI1-TEIG) are not handled autonomously by the ISAC-S TE. In auto and non-auto-modes with one-byte address field, TEI1 is a command address, according to X.25 LAPB. 4.1.18 Receive HDLC Control Register RHCR 7 Read Address 29 H 0 In all modes except transparent modes 2 and 3, this register contains the control field of a received HDLC frame. In transparent modes 2 and 3, the register is not used. SAPI1 Contents of RHCR Mode Modulo 8 (MCS = 0) Modulo 128 (MCS = 1) Contents of RFIFO Auto-mode, Control field 1-byte address (U/I frames) (Note 1) U-frames only: From 3rd byte after flag Control field (Note 4) (Note 2) Auto-mode, Control field 2-byte address (U/I frames) (Note 1) U-frames only: From 4th byte after flag Control field (Note 4) (Note 2) Auto-mode, 1-byte address (I frames) Control field in From 4th byte after flag compressed form (Note 4) (Note 3) Auto-mode, 2-byte address (I frames) Control field in From 5th byte after flag compressed form (Note 4) (Note 3) Non-auto mode, 1-byte address 2nd byte after flag From 3rd byte after flag Non-auto mode, 2-byte address 3rd byte after flag From 4th byte after flag Transparent mode 1 3rd byte after flag From 4th byte after flag Transparent mode 2 - From 1st byte after flag Transparent mode 3 - From 2nd byte after flag Semiconductor Group 160 Register Description Note 1: S frames are handled automatically and are not transferred to the microprocessor. Note 2: For U frames (bit 0 of RHCR = 1) the control field is as in the modulo 8 case. Note 3: For I frames (bit 0 of RHCR = 0) the compressed control field has the same format as in the modulo 8 case, but only the three LSB's of the receive and transmit counters are visible: 7 0 N(R)2-0 P N(S)2-0 0 Note 4: I field. 4.1.19 TEI2 Register TEI2 Write Address 29H 7 0 EA TEI2 EA Address Field Extension Bit This bit is to be set to "1" according to HDLC/LAPD. In all message transfer modes except in transparent modes 2 and 3, TEI2 is used by the ISAC-S TE for address recognition. In the case of a two-byte address field, it contains the value of the second programmable Terminal Endpoint Identifier according of the ISDN LAPD protocol. In auto and non-auto modes with one-byte address field, TEI2 is a response address, according to X.25 LAPB. 4.1.20 Receive Frame Byte Count High RBCH Read Address 2AH Value after reset: 0XX000002. 7 0 XAC XAC VN1 VN0 OV RBC11 RBC10 RBC9 RBC8 Transmitter Active The HDLC transmitter is active when XAC = 1. This bit may be polled. The XAC bit is active when - either an XTF/XIF command is issued and the frame has not been completely transmitted - or the transmission of an S frame is internally initiated and not yet completed. VN1-0 Version Number of Chip 00 ... V1.1 version Semiconductor Group 161 Register Description OV Overflow A "1" in this bit position indicates a message longer than 4095 bytes. RBC8-11Receive Byte Count Four most significant bits of the total number of bytes in a received message. Note: Normally RBCH and RBCL should be read by the processor after an RME interrupt in order to determine the number of bytes to be read from the RFIFO, and the total message length. The contents of the registers are valid only after an RME interrupt, and remain so until the frame is acknowledged via the RMC bit. 4.1.21 Status Register 2 STAR2 Read/Write Address 2BH Value after reset: 00H a) WRITE 7 0 0 MULT 0 0 0 0 MULT 0 0 Used to enable or disable the multiframe structure (see chapter 2.4.9) 1: S/T multiframe disabled 0: S/T multiframe enabled b) READ 7 0 0 0 0 0 WFA MULT TREC SDET WFA Waiting for Acknowledge This bit shows, if the last transmitted I frame was acknowledged, i.e. V(A) = V(S) ( WFA = 0) or was not yet acknowledged, i.e. V(A) < V(S) ( WFA = 1). MULT The value written into the register bit is read. TREC Timer Recovery Status: 0: The device is not in the timer recovery state. 1: The device is in the timer recovery state. SDET S Frame Detected: This bit is set to "1" by the first received correct I frame or S command with p = 1. It is reset by reading STAR2. Semiconductor Group 162 Register Description 4.2 Special Purpose Registers: IOM(R)-2 Mode The following register description is only valid if IOM-2 is selected (ADF2:IMS-1). 4.2.1 Serial Port Control Register Value after reset: SPCR Read/Write Address 30H 00H 7 0 SPU Important Note SPU 0 0 TLP C1C1 C1C0 C2C1 C2C0 After a hardware reset the pin SDS1 is "low" until the SPCR is written to for the first time. From that moment on, the function taken on by these pins depends on the state of the IOM Mode Select bit IMS (ADF2 register). Software Power-Up. Used in TE mode only. If SQXR:CFS = 1, before activating the ISDN S interface in TE mode the SPU and SQXR:IDC bits have to be set to "1" and then cleared again: After a subsequent CISQ interrupt (C/I code change; ISTA) and reception of the C/I code "PU" (Power-Up indication in TE mode) the reaction of the processor would be: TLP - to write an activate request command as C/I code in the CIX0 register. - to reset the SPU and SQXR:IDC bits and wait for the following CISQ interrupt. Test Loop When set to 1 the IDP1 and IDP0 lines are internally connected together, and the times T1 and T2 are reduced (cf. TIMR). C1C1, C1C0 Channel 1 Connect Determines which of the two channels B1 or IC1 is connected to register C1R and/or B1CR, for monitoring, test-looping and switching data to/from the processor. C1R B1CR C1C1 C1C0 Read Write Read Application(s) 0 0 1 0 1 0 IC1 IC1 - - IC1 B1 B1 B1 B1 1 1 B1 B1 - B1 monitoring + IC1 monitoring B1 monitoring + IC1 looping from/to IOM B1 access from/to S0; transmission of a constant value in B1 channel to S0. B1 looping from S0; transmission of a variable pattern in B1 channel to S0. Semiconductor Group 163 Register Description C2C1, C2C0 Channel 2 Connect Determines which of the two channels B2 or IC2 is connected to register C2R and/or B2CR, for monitoring, test-looping and switching data to/from the processor. C2R B2CR C2C1 C2C0 Read Write Read Application(s) 0 0 1 0 1 0 IC2 IC2 - - IC2 B2 B2 B2 B2 1 1 B2 B2 - B2 monitoring + IC2 monitoring B2 monitoring + IC2 looping from/to IOM B2 access from/to S0; transmission of a constant value in B2 channel to S0. B2 looping from S0; transmission of a variable pattern in B2 channel to S0. 4.2.2 Command/Indication Receive 0 Value after reset: CIR0 Read Address 31H 7CH 7 0 SQC SQC BAS CODR0 CIC0 CIC1 S/Q Channel Change A change in the received 4-bit S-channel (TE or LT-T mode) has been detected. The new code can be read from the SQRR. This bit is reset by a read of the SQRR. BAS Bus Access Status Indicates the state of the TIC bus: 0: the ISAC-S TE itself occupies the D and C/I channel 1: another device occupies the D and C/I channel CODR0 C/I Code 0 Receive Value of the received Command/Indication code. A C/I code is loaded in CODR0 only after being the same in two consecutive IOM frames and the previous code has been read from CIR0. (refer to chapter 3.3.2) CIC0 C/I Code 0 Change A change in the received Command/Indication code has been recognized. This bit is set only when a new code is detected in two consecutive IOM frames. It is reset by a read of CIR0. Semiconductor Group 164 Register Description CIC1 C/I Code 1 Change A change in the received Command/Indication code in IOM channel 1 has been recognized. This bit is set when a new code is detected in one IOM frame. It is reset by a read of CIR0. CIC1 is only used if terminal mode is selected. Note: The BAS and CODR0 bits are updated every time a new C/I code is detected in two consecutive IOM frames. If several consecutive valid new codes are detected and CIR0 is not read, only the first and the last C/I code (and BAS bit) is made available in CIR0 at the first and second read of that register, respectively. 4.2.3 Command/Indication Transmit 0 Value after reset: CIX0 Write Address 31H 3FH 7 0 RSS RSS BAC CODX0 1 1 Reset Source Select Only valid if the terminal specific functions are activated (STCR:TSF). 0: Subscriber or Exchange Awake As reset source serves: - a falling edge on the EAW line (External Subscriber Awake) - a C/I code change (Exchange Awake). A logical zero on the EAW line activates also the IOM-interface clock and frame signal, just as the SPU-bit (SPCR) does. 1: Watchdog Timer The expiration of the watchdog timer generates a reset pulse. The watchdog timer will be reset and restarted, when two specific bit combinations are written in the ADF1 register within the time period of 128 ms (see also ADF1 register description). After a reset pulse generated by the ISAC-S TE and the corresponding interrupt (WOV, SAW or CISQ) the actual reset source can be read from the ISTA and EXIR register. BAC Bus Access Control Only valid if the TIC-bus feature is enabled (MODE:DIM2-0). If this bit is set, the ISAC-S TE will try to access the TIC bus to occupy the C/I channel even if no D-channel frame has to be transmitted. It should be reset when the access has been completed to grant a similar access to other devices transmitting in that IOM channel. Semiconductor Group 165 Register Description Note: Access is always granted by default to the ISAC-S TE/ICC with TIC-bus address (TBA2-0, STCR register) "7", which has the lowest priority in a bus configuration. CODX0 C/I Code 0 Transmit Code to be transmitted in the C/I channel / C/I channel 0. (refer to chapter 3.3.2) 4.2.4 MONITOR Receive Channel 0 MOR0 Read Address 32H 7 0 Contains the MONITOR data received in IOM MONITOR channel/ MONITOR channel 0 according to the MONITOR channel protocol. 4.2.5 MONITOR Transmit Channel 0 MOX0 Write Address 32H 7 0 Contains the MONITOR data to be transmitted in IOM MONITOR channel/ MONITOR channel 0 according to the MONITOR channel protocol. 4.2.6 Command/Indication Receive 1 Value after reset: CIR1 Read Address 33H FFH 7 0 MR1 CODR1 MX1 CODR1 C/I Code 1 Receive Bits 7-2 of C/I channel 1 MR1 MR Bit Bit 1 of C/I channel 1 MX1 MX Bit Bit 0 of C/I channel 1 4.2.7 Command/Indication Transmit 1 Semiconductor Group CIX1 166 Write Address 33H Register Description Value after reset: FFH 7 0 1 CODX1 1 CODX1 C/I Code 1 Transmit Bits 7-2 of C/I channel 1 4.2.8 MONITOR Receive Channel 1 MOR1 Read 7 Address 34H 0 Contains the MONITOR data received in IOM channel 1 according to the MONITOR channel protocol. 4.2.9 MONITOR Transmit Channel 1 MOX1 7 Write Address 34H 0 Contains the MONITOR data to be transmitted in IOM channel 1 according to the MONITOR channel protocol. 4.2.10 Channel Register 1 C1R 7 Read/Write Address 35H 0 Contains the value received/transmitted in IOM channel B1 or IC1, as the case may be (cf. C1C1, C1C0, SPCR register). 4.2.11 Channel Register 2 C2R 7 Read/Write Address 36H 0 Contains the value received/transmitted in IOM channel B2 or IC2, as the case may be (cf. C2C1, C2C0, SPCR register). Semiconductor Group 167 Register Description 4.2.12 B1-Channel Register B1CR Read Address 37H 7 0 Contains the value received in IOM channel B1, if programmed (see C1C1, C1C0, SPCR register). 4.2.13 Synchronous Transfer Control RegisterSTCR Value after reset: Write Address 37H 00H 7 0 TSF TSF TBA2 TBA1 TBA0 ST1 ST0 SC1 SC0 Terminal Specific Functions 0: No terminal specific functions 1: The terminal specific functions are activated, such as - Watchdog Timer - Subscriber/Exchange Awake (EAW). In this case the EAW line is always an input signal which can serve as a request signal from the subscriber to initiate the awake function in a terminal. A falling edge on the EAW line generates an SAW interrupt (EXIR). When the RSS bit in the CIX0 register is zero, a falling edge on the EAW line (Subscriber Awake) or a C/I code change (Exchange Awake) initiates a reset pulse. When the RSS bit is set to one a reset pulse is triggered only by the expiration of the watchdog timer (see also CIX0-register description). Note: The TSF bit will be cleared only by a hardware reset. TBA2-0 TIC-Bus Address Defines the individual address for the ISAC-S TE on the IOM TIC bus (see chapter 2.3.6). This address is used to access the C/I- and D-channel on the IOM. Note: One device liable to transmit in C/I- and D-fields on the IOM should always be given the address value "7". Semiconductor Group 168 Register Description ST1 Synchronous Transfer 1 When set, causes the ISAC-S TE to generate an SIN-interrupt status (ISTA register) at the beginning of an IOM frame. ST0 Synchronous Transfer 0 When set, causes the ISAC-S TE to generate an SIN-interrupt status (ISTA register) at the middle of an IOM frame. SC1 Synchronous Transfer 1 Completed After an SIN interrupt the processor has to acknowledge the interrupt by setting the SC1 bit before the middle of the IOM frame, if the interrupt was originated from a Synchronous Transfer 1 (ST1). Otherwise an SOV interrupt (EXIR register) will be generated. SC0 Synchronous Transfer 0 Completed After an SIN interrupt the processor has to acknowledge the interrupt by setting the SC0 bit before the start of the next IOM frame, if the interrupt was originated from a Synchronous Transfer 0 (ST0). Otherwise an SOV interrupt (EXIR register) will be generated. Note: ST0/1 and SC0/1 are useful for synchronizing MP accesses and receive/transmit operations. 4.2.14 B2-Channel Register B2CR Read 7 0 Used only in terminal mode (SPCR:SPM = 0). Contains the value received in the IOM channel B2, if programmed (see C2C1, C2C0, SPCR register). Semiconductor Group Address 38H 169 Register Description 4.2.15 Additional Feature Register 1 Value after reset: ADF1 Write Address 38H 00H 7 0 WTC1 WTC2 TEM PFS IOF 0 0 ITF WTC1, 2 Watchdog Timer Control 1, 2 After the watchdog timer mode has been selected (STCR:TSF = CIX0:RSS = 1) the watchdog timer is started. During every time period of 128 ms the processor has to program the WTC1- and WTC2 bit in the following sequence: 1. 2. WTC1 WTC2 1 0 0 1 to reset and restart the watchdog timer. If not, the timer expires and a WOV interrupt (EXIR) together with a reset pulse is generated. TEM Test Mode In test mode (TEM = 1, PFS = 0) all layer-1 functions are disabled and the ISAC-S TE behaves like an ICC (PEB 2070) device. PFS Prefilter Select These bits together determine the pre-filter delay compensation and the test mode (layer 1 disabled) of the ISAC-S TE, as follows: IOF TEM PFS Effect 0 0 No pre-filter (0 delay) 0 1 Pre-filter delay compensation 520 ns 1 1 Pre-filter delay compensation 910 ns 1 0 Test mode (layer 1 disabled) IOM OFF. Used in terminal mode (SPCR:SPM = 0). 0: IOM interface is operational 1: IOM interface is switched off (DCL, FSC1, IDP0/1, BCL high impedance). Note: IOF should be set to "1" if external devices connected to the IOM interface should be "disconnected" e.g. for power saving purposes or for not disturbing the internal IOM connection between layer 2 and layer 1. However, the internal operation is independent of the IOF bit. Semiconductor Group 170 Register Description ITF Inter-Frame Time Fill Selects the inter-frame time fill signal which is transmitted between HDLC frames. 0: idle (continuous 1 s), 1: flags (sequence of patterns: "0111 1110") Note: 4.2.16 In TE applications with D-channel access handling (collision resolution), the only possible inter-frame time fill signal is idle (continuous 1 s). Otherwise the D channel on the S/T bus cannot be accessed. Additional Feature Register 2 Value after reset: ADF2 Read/Write Address 39H 00H 7 0 IMS IMS 0 0 0 ODS D1C2 D1C1 D1C0 IOM Mode Selection IOM-2 interface mode is selected when IMS = 1. ODS Output Driver Selection Tristate drivers (1) or open drain drivers (0) are used for the IOM interface. D1C2-0 Data Strobe Control These bits determine the polarity of the two independent strobe signals SDS1 as follows: D1C2 D1C1 D1C0 SDS1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 always low high during B1 high during B2 high during B1 + B2 always low high during IC1 high during IC2 high during IC1 + IC2 The strobe signals allow standard combos or data devices to access a programmable channel. Semiconductor Group 171 Register Description 4.2.17 MONITOR Status Register MOSR Read Address 3AH Value after reset: 00H 7 0 MDR1 MER1 MDA1 MAB1 MDR0 MDR1 MONITOR Channel 1 Data Received MER1 MONITOR Channel 1 End of Reception MDA1 MONITOR Channel 1 Data Acknowledged MER0 MDA0 MAB0 The remote end has acknowledged the MONITOR byte being transmitted. MAB1 MONITOR Channel 1 Data Abort MDR0 MONITOR Channel 0 Data Received MER0 MONITOR Channel 0 End of Reception MDA0 MONITOR Channel 0 Data Acknowledged The remote end has acknowledged the MONITOR byte being transmitted. MAB0 MONITOR Channel 0 Data Abort 4.2.18 MONITOR Control Register MOCR Write Address 3AH Value after reset: 00H 7 0 MRE1 MRE1,0 MRC1 MXE1 MXC1 MRE0 MRC0 MXE0 MXC0 MONITOR Receive Interrupt Enable (IOM channel 1,0) MONITOR interrupt status MDR1/MDR0, MER1/0 generation is enabled (1) or masked (0). MRC1,0 MR Bit Control (IOM Channel 1,0) Determines the value of the MR bit: 0: MR always "1". In addition, the MDR1/MDR0 interrupt is blocked, except for the first byte of a packet (if MRE1/0 = 1). 1: MR internally controlled by the ISAC-S TE according to MONITOR channel protocol. In addition, the MDR1/MDR0 interrupt is enabled for all received bytes according to the MONITOR channel protocol (if MRE1 0 = 1). Semiconductor Group 172 Register Description MXE1,0 MONITOR Transmit Interrupt Enable (IOM channel 1,0) MONITOR interrupt status MDA1/0, MAB1/0 generation is enabled (1) or masked (0). MXC1,0 MX Bit Control (IOM channel 1,0) Determines the value of the MX bit: 0: MX always "1". 1: MX internally controlled by the ISAC-S TE according to MONITOR channel protocol. 4.2.19 S-, Q-Channel Receive Register Value after reset: SQRR Read Address 3BH 0XH 7 0 IDC CFS CI1E SYN SQR1 SQR2 SQR3 IDC Read-Back of Programmed IDC Bit (see SQXR register) CFS Read-Back of Programmed CFS Bit (see SQXR register) CI1E Read-Back of Programmed CI1E Bit (see SQXR register) SYN Synchronization State SQR4 The S/T receiver has synchronized to the received FA and M bits (1) or has not (0). SQR1-4 Received S/Q Bits Received S bits in frames 1, 6, 11 and 16, respectively. Semiconductor Group 173 Register Description 4.2.20 S, Q Channel Transmit Register Value after reset: SQXR Write Address 3BH 0FH 7 0 IDC IDC CFS CI1E SQIE SQX1 SQX2 SQX3 SQX4 IOM Direction Control 0: Master (normal) mode Layer 2 transmits IOM channel 0 and 2 on IDP1, channel 1 on IDP0. 1: Slave (test) mode Layer 2 transmits IOM channel 0, 1 and 2 on IDP1. Note: Also refer to chapter 2.3.2 CFS Configuration Select This bit determines clock relations and recovery on S/T and IOM interfaces. 0: The IOM interface clock and frame signals are always active, "Power-Down" state included. The states "Power-Down" and "Power-Up" are thus functionally identical except for the indication: PD = 1111 and PU = 0111. With the C/I-command Timing (TIM) the processor can enforce the "Power-Up" state. With C/I-command Deactivation Indication (DIU) the "Power-Down" state is reached again. However, it is also possible to activate the S-interface directly with the C/I-command Activate Request (AR 8/10/L) without the TIM command. 1: The IOM-interface clock and frame signals are normally inactive Power-Down"). For activating the S interface the "Power-Up" state can be induced by software (SPU bit in SPCR register). After that the S interface can be activated with the C/I-command Activate Request (AR 8/10/L). The "Power-Down" state can be reached again with the C/I commandDeactivation Indication (DIU). Note: After reset the IOM interface is always active. To reach the "Power-Down" state the CFS bit has to be set. Semiconductor Group 174 Register Description CI1E C/I Channel 1 Interrupt Enable Interrupt generation of CIR0:CIC1 is enabled (1) or masked (0). SQIE S-, Q-Interrupt Enable Generation of CIR0:SQC status (and the accompanying CISQ interrupt is enabled (1) or masked (0). SQX1-4 Transmitted Q Bits transmitted FA bits in frames 1, 6, 11 and 16, respectively. Semiconductor Group 175 Electrical Characteristics 5 Electrical Characteristics Absolute Maximum Ratings Parameter Symbol Limit Values Unit Voltage on any pin with respect to ground VS - 0.4 to VDD + 0.4 V Ambient temperature under bias TA 0 to 70 C Storage temperature Tstg - 65 to 125 C Maximum voltage on V DD VDD 6 V Note: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Line Overload Protection The maximum input current (under overvoltage conditions) is given as a function of the width of a rectangular input current pulse (figure 54). R ISAC -S TE Condition: All other pins grounded t t WI ITS05678 Figure 54 Test Condition for Maximum Input Current Semiconductor Group 176 Electrical Characteristics Transmitter Input Current The destruction limits for negative input signals are given in figure 55. Ri 2 . A 100 50 10 5 1 0.5 0.05 t WI 10 -10 10 -9 10 -8 10 -7 10 -6 10 -5 10 -4 10 -3 10 -2 10 -1 1 s ITD02337 Figure 55 The destruction limits for positive input signals are given in figure 56. Ri 200 . A 50 5 0.5 0.05 t w1 10 -10 10 -9 10 -8 10 -7 10 -6 10 -5 10 -4 10 -3 10 -2 10 -1 1 s ITD02340 Figure 56 Semiconductor Group 177 Electrical Characteristics Receiver Input Current The destruction limits are given in figure . Ri 300 . A 5 1 0.1 0.01 0.005 t w1 10 -10 10 -4 10 -1 1 s ITD02338 Semiconductor Group 178 Electrical Characteristics DC Characteristics TA = 0 to 70 C; VDD = 5 V 5 %, VSSA = 0 V, VSSD = 0 V Parameter Symbol Limit Values min max Unit Test Condition Remarks All pins except SX1,2, SR1,2 L-input voltage VIL - 0.4 0.8 V H-input voltage VIH 2.0 VDD + 0.4 V L-output voltage L-output voltage (IDP0) VOL VOL1 0.45 0.45 V V IOL = 2 mA IOL = 7 mA H-output voltage H-output voltage VOH VOH V V IOH = - 400 A IOH = - 100 A Power supply current ICC 2.4 VDD - 0.5 1.5 mA 17 mA DCL = 1536 kHz Emergency B1 = FFH, B2 = FFH, D=1 7.7 mA DCL = 1536 kHz B1 = FFH, B2 = FFH, D = Flag 7.95 mA DCL = 1536 kHz B1 = 55H, B2 = FFH, D = Flag 8.75 mA DCL = 1536 kHz B1 = 00H, B2 = FFH, D = Flag 10 mA DCL = 1536 kHz ILI 10 A 0 V < VIN < VDD to 0 V ILO 10 A 0 V < VOUT < VDD to 0 V power down operational (96 kHz) Input leakage current Output leakage current Semiconductor Group 179 VDD = 5 V Inputs at VSS / VDD No output loads except SX1,2 (50 load) All pins except CP/BCL, X2, SX1,2, SR1,2, A0, A1, A3, A4 Electrical Characteristics DC Characteristics TA = 0 to 70 C; VDD = 5 V 5 %, VSSA = 0 V, VSSD = 0 V (cont'd) Parameter Symbol Limit Values min Unit Test Condition Remarks 120 A 0 V < VIN < VDD to 0 V A0, A1, A3, A4, CP/BCL, X2 SX1,2 max Input leakage current internal pull-down ILIPD Absolute value of output pulse amplitude (VSX2 - VSX1) VX 2.03 2.10 2.31 2.39 V V RL = 50 1) RL = 400 1) Transmitter output current IX 7.5 13.4 mA RL = 5.6 1) Transmitter output impedance RX 10 0 k Inactive or during binary one during binary zero RL = 50 Receiver output voltage VSR1 2.35 2.6 V IO < 5 A Receiver threshold voltage VSR2 - VSR1 VTR 225 375 mV Dependent on peak level Note: 1) SR1,2 Due to the transformer, the load resistance seen by the circuit is four times RL. Semiconductor Group 180 Electrical Characteristics Capacitances TA = 25 C, VDD = 5 V 5 %, VSSA = 0 V, VSSD = 0 V, fc =1 MHz, unmeasuredpins grounded. Parameter Symbol Limit Values Unit Remarks min. max. Input capacitance I/O capacitance CIN CI/O 7 7 pF pF All pins except SR1,2 Output capacitance against VSSA COUT 10 pF SX1,2 Input capacitance CIN 7 pF SR1,2 Load capacitance CL 50 pF XTAL1,2 Recommended Oscillator Circuits 33 pF 19 XTAL1 External Oscillator Signal XTAL 2 N.C. CL 19 XTAL1 7.68 MHz 33 pF 18 18 XTAL 2 CL Crystal Oscillator Mode Driving from External Source ITS00764 Figure 57 Oscillator Circuits Crystal Specification Parameter Symbol Limit Values Unit Frequency f 7.680 MHz max. 100 ppm max. 50 pF Frequency calibration tolerance Load capacitance CL Oscillator mode fundamental Note: The load capacitance CL depends on the recommendation of the crystal specification. Typical values for CL are 22 ...33 pF. Semiconductor Group 181 Electrical Characteristics XTAL1 Clock Characteristics (external oscillator input) Parameter Limit Values Duty cycle min. max. 1:2 2:1 AC Characteristics T A = 0 to 70 C, V DD = 5 V 5% Inputs are driven to 2.4 V for a logical "1" and to 0.4 V for a logical "0". Timing measurements are made at 2.0 V for a logical "1" and 0.8 V for a logical "0". The AC-testing input/output waveforms are shown in figure 58. 2.4 2.0 2.0 Device Under Test Test Points 0.8 0.8 C Load = 150 pF 0.45 ITS00621 Figure 58 Input/Output Waveform for AC Tests Semiconductor Group 182 Electrical Characteristics Microprocessor Interface Timing Siemens/Intel Bus Mode t RR t RI RD x CS t DF t RD Data AD0 - AD7 ITT00712 Figure 59 Microprocessor Read Cycle t WW t WI WR x CS t WD t DW Data AD0 -AD7 ITT00713 Figure 60 Microprocessor Write Cycle t AA t AD ALE WR x CS or RD x CS t ALS t AL AD0 - AD7 t LA Address ITT00714 Figure 61 Multiplexed Address Timing Semiconductor Group 183 Electrical Characteristics WR x CS or RD x CS t AS A0 - A5 t AH Address ITT00715 Figure 62 Non-Multiplexed Address Timing Motorola Bus Mode R/W t DSD t RWD t RI t RR CS x DS t DF t RD D0 - D7 Data ITT00716 Figure 63 Microprocessor Read Timing Figure 64 Microprocessor Write Cycle Semiconductor Group 184 Electrical Characteristics CS x DS t AS t AH AD0 - AD5 ITT00718 Figure 65 Non-Multiplexed Address Timing Microprocessor Interface Timing Parameter Symbol Limit Values min. Unit max. ALE pulse width tAA 50 ns Address setup time to ALE tAL 15 ns Address hold time from ALE tLA 10 ns Address latch setup time to WR, RD tALS 0 ns Address setup time tAS 25 ns Address hold time tAH 10 ns ALE guard time tAD 15 ns DS delay after RW setup tDSD 0 ns RD pulse width tRR 110 ns Data output delay from RD tRD 110 ns Data float from RD tDF 25 ns RD control interval tRI 70 ns W pulse width tWW 60 ns Data setup time to W x CS tDW 35 ns Data hold time from W x CS tWD 10 ns W control interval tWI 70 ns Semiconductor Group 185 Electrical Characteristics Serial Interface Timing FSC1 (O) t IIS t FSD DCL (O) t IIH IDP0/1 ( ) t IOD IDP0/1 (O) t SDD SDS1 (O) t BCD t BCD BCL (O) ITD05435 Figure 66 IOM(R) Timing (TE mode) IOM(R) Timing Parameter Symbol Limit Values min. max. 100 Unit Test Condition ns IOM-2 IOM-2 IOM output data delay tIOD 20 IOM input data setup tIIS 20 ns IOM input data hold tIIH 20 ns FSC1 strobe delay tFSD - 20 Strobe signal delay tSDD Bit clock delay tBCD Semiconductor Group - 20 186 20 ns 120 ns 20 ns Electrical Characteristics HDLC Mode (ADF2: IMS = 0, ADF1: TEM = 1, MODE: DIM2 - 0 = 101 - 111) Figure 67 FSC1 (strobe) Characteristics HDLC Mode Timing Parameter Symbol Limit Values min. Unit max. FSC1 set-up time tFS1 100 ns FSC1 hold time tFH1 30 ns Output data from high impedance to active tOZD 80 ns Output data from active to high impedance tODZ 40 ns Output data delay from DCL tODD 20 100 ns Input data setup tIS 10 ns Input data hold tDH 30 ns Semiconductor Group 187 Electrical Characteristics Clock Timing The clocks are summarized in table 20, with the respective duty ratios. Table 20 ISAC(R)-S TE Clock Signals (IOM(R)-2 mode) Application DCL FSC1 BCL SDS1 TE o:1536 kHz* 3:2 o:8 kHz* 1:2 o:768 kHz* 1:1 o:8 kHz 1:11 2:10 The 1536-kHz clock is phase-locked to the receive S signal, and derived using the internal DPLL and the 7.68 MHz 100 ppm crystal. A phase tracking with respect to "S" is performed once in 250 s. As a consequence of this DPLL tracking, the "high" state of the 1536-kHz clock may be either reduced or extended by one 7.68-MHz period (duty ratio 2:2 or 4:2 instead of 3:2) once every 250 s. Since the other signals are derived from this clock, the "high" or "low" states may likewise be reduced or extended by the same amount once every 250 s. The phase relationships of the clocks are shown in figure 68. 7.68 MHz 1536 kHz * * Synchronous to receive S/T. Duty Ratio 3 : 2 Normally 768 kHz ITD05427 Figure 68 Phase Relationships of ISAC(R)-S TE Clock Signals *) Synchronous to receive "S" line Semiconductor Group 188 Electrical Characteristics R DCL (IOM -2) t BCD t BCD BCL t FSD FSC1 t SSD t SBD SDS1 ITD05428 Figure 69 Timing Relationships between ISAC(R)-S TE Clock Signals Table 21 Parameter Symbol Limit Values Unit Condition min. max. - 20 20 ns IOM-2 Bit clock delay tBCD SDS1 delay from DCL tSDD 120 ns IOM-2 SDS1 delay from BCL tSBD 120 ns IOM-2 Semiconductor Group 189 Electrical Characteristics 3.5 V 0.8 V t WH t WL tP ITT00723 Figure 70 Definition of Clock Period and Width Table 22 DCL-Clock Characteristics (IOM(R)-2) Parameter (TE) 1536 kHz Semiconductor Group Symbol Limit Values Unit Test Condition min. typ. max. tPO 520 651 782 ns osc 100 ppm tWHO 240 391 541 ns osc 100 ppm tWLO 240 260 281 ns osc 100 ppm 190 Electrical Characteristics Jitter In TE mode, the timing extraction jitter of the ISAC-S conforms to CCITT Recommendation I.430 (- 7 % to + 7 % of the S-interface bit period). Description of the Receive PLL (RPLL) of the ISAC-S TE The receive PLL performs phase tracking each 250 s after detecting the phase between the F/L transition of the receive signal and the recovered clock. Phase adjustment is done by adding or subtracting 130 ns to or form a 1.536-MHz clock cycle. The 1.536-MHz clock is than used to generate any other clock synchronized to the line. During (re)synchronization an internal reset condition may effect the 1.536-MHz clock to have high or low times as short as 130 ns. After the S/T-interface frame has achieved the synchronized state (after three consecutive valid pairs of code violations) the FSC output is set to a specific phase relationship, thus causing once an irregular FSC timing. Reset Table 23 Reset Signal Characteristics Parameter Symbol Limit Values Unit Test Condition ms Power-on/Power-Down to Power-Up (Standby) min. Length of active high state tRST 4 2 x DCL clock cycles During Power-Up (Standby) t RST RST ITD02396 Figure 71 Reset Semiconductor Group 191 Low Level Controller 6 ISAC(R)-S TE Low Level Controller The following paragraphs outline the functionality and structure of a software driver example for the ISAC-S TE. This example is based on the Siemens Low Level Controllers (LLC's) for Basic Access IC which are available in C source code. The ISAC-S TE software driver will be also referred to as LLC or ISAC-S LLC. It should be noted that the ISAC-S LLC does not access the complete palette of device functions but rather a subset of them. For example not all message transfer modes are supported. Please refer to paragraph 'Architecture and Functions' for a more detailed description. The ISAC-S LLC presented here has been successfully tested in the Siemens ISDN PC development system. Correct operation with a higher layer software has been verified by using the Siemens ISDN-Software Development and Evaluation System (SIDES) and the Siemens ISDN-Operational Software (IOS). The ISAC-S LLC also apply for the ISAC(R)-S TE with the limitation of TE functionality only. There is no adaptation in the listing to this limitation. 6.1 Architecture and Functions The ISAC-S TE LLC may be divided into two major parts, one for layer 1 control, the 'SBC part' and one for directing the HDLC-controller operations, the 'ICC part'. The naming conventions 'SBC part' and 'ICC part' have been introduced for two reasons: The first is that the ISAC-S TE may be viewed as the one-chip integration of the Siemens ISDN Communications Controller, PEB 2070 ICC, and the S-Bus Interface Circuit, PEB 2080 SBC. The second is that the SIPBmainboard firmware, the basis for this example software, actually uses the same code to control either an ISAC-S TE or an ICC-SBC combination. The ISAC-S TE LLC consists of driver functions and interrupt server. The driver functions are implemented as a set of C functions which are responsible for interpreting hardware related commands from the higher layers and carrying out the appropriate actions at the hardware level. Driven by hardware interrupts, the interrupt server analyses the hardware event and informs the higher software layers of that event. It should be noted that this implementation has attempted to remove as many protocol specific functions as possible from the LLC and to locate them instead in the higher layer protocol itself. This has the advantage of making the LLC- more general and less likely to be in need of reprogramming for different protocols. Semiconductor Group 192 Low Level Controller OPERATING SYSTEM and Higher Level Protocol Software Status/ Error Messages FUNCTION CALLS Received Frames MMU - Service Requests ... Interrupt Server Driver Functions SBC Part ICC Part Layer-1 Functions HDLC Controller related Functions SBC Part ICC Part Evaluation of Interrupt Cause R ISAC -S TE ITS05679 Figure 73 LLC Architecture The ISAC-S TE LLC supports following standard functions: - Initialization of the SBC (layer 1) part. - Activation of layer 1. - Deactivation of layer 1. HDLC-controller initialization. The following HDLC-controller message transfer modes are supported: auto-mode: full two byte address compare, LAPD support. non-auto mode: full two byte address compare. transparent mode 3: high byte address compare; called 'TRANSPARENT' mode in the LLC. transparent mode 2: no address compare; called 'EXTENDED TRANSPARENT' mode in the LLC. HDLC framing with two byte address field is assumed. Semiconductor Group 193 Low Level Controller - - - - HDLC-frame transmission. Programming of TEI and SAPI values. HDLC-transceiver control. Local test loop switching. The LLC assumes that the ISAC-S TE is operating in an IOM-2 TE configuration. In addition to the ISAC-S TE standard functions supporting the ISDN-basic access, the ISAC-S TE contains optional, terminal specific functions. These terminal specific functions (watchdog and external awake) are not supported by this LLC. 6.2 Summary of LLC Functions 6.2.1 Layer-1 Related Functions Mnemonic ActL1_SBC DeaL1_SBD ArlL1_SBC EnaClk_SBC InitL1_SBC ResL1_SBC Purpose Layer-1 activation. Layer 1 deactivation. Activation of a local loop. Enable clocking in power down mode. Layer-1 initialization and reset. Layer-1 reset. IntL1_SBC Handling of CISQ interrupts. The layer 1 related functions call DECODE_L1_STATUS to report a L1 status change to a higher layer software. 6.2.2 HDLC-Controller Related Functions Mnemonic InitLay2_ICC Loop_ICC ResetHDLC_ICC RecReady_ICC SendFrame_ICC StoreSAPI_ICC StoreTEI_ICC Purpose HDLC-controller initialization. Testloop activation at the serial outputs of the IOM interface. HDLC-transceiver reset. Setting the HDLC receiver ready or not ready. HDLC-frame transmission. SAPI programming. TEI programming. Int_ICC Rx_ICC Handling of XPR, RSC, TIN and EXI interrupts. Handling of RPF and RME interrupts. Semiconductor Group 194 Low Level Controller 6.2.3 External Functions The LLC-program listing shows some references to external functions (indicated by an 'IMPORT' declaration). These functions are used by the LLC but are not part of it. These external functions must be provided by the operating system or a higher layer protocol software. MMU_req () By calling MMU_req the ISAC-S TE LLC requests memory for the temporary storage of a received data frame. The memory management unit (MMU) of the operating system has to provide a memory buffer of the required size (max. 260 bytes). MMU_free () MMU_free is the counterpart to MMU_req. The operating system can release a previously allocated memory buffer. STRING_IN () and STRING_OUT () STRING_IN and STRING_OUT are assembler written functions for fast input and output of data frames from/to the ISAC-S FIFO. ENTERNOINT () and LEAVENOINT () ENTERNOINT and LEAVENOINT are called to disable and enable all system interrupts in time critical sections. Decode_S_Frame_BASIC () Decode_S_Frame_BASIC is called by the LLC-interrupt server to transfer a received HDLC S frame to a higher layer protocol software. Following information is passed to Decode_S_Frame_BASIC: 'pei': 1-byte value identifying the performed address recognition. The bits 0, 1 and 2 of 'pei' represent the bits TA, SA0 and SA1 of the ISAC-S' RSTA register. 'sapi': 1-byte value representing the received HDLC SAPI address byte. Bit 1 of 'sapi' is the C/R bit value (RSTA:CR). The most significant 6 bits of 'sapi' are 0 in auto-mode, non-auto mode and transparent mode. 'tei': 1-byte value representing the received HDLC TEI address byte. 'tei' is 0 in auto-mode and non-auto mode. 'ctrl': 2-byte value representing the contents of the received HDLC-control field. 'frame_status': 1 byte value = 0 x 00: frame is valid. = 0 x 80: frame is mutilated (last byte of two byte control field missing). = 0 x 82: frame is too long. S frame with I field. 'M128': 1-byte value. 0 in modulo 8 operating mode (1-byte control field), 1 in modulo 128 operating mode (2-byte control field). For correct decoding of 'ctrl' above. Semiconductor Group 195 Low Level Controller Decode_U_Frame_BASIC () Decode_U_Frame_BASIC is called by the LLC-interrupt server to transfer a received HDLC U frame to a higher layer protocol software. Following information is passed to Decode_U_Frame_BASIC: 'pei': (refer to Decode_S_Frame). 'sapi': (refer to Decode_S_Frame). 'tei': (refer to Decode_S_Frame). 'ctrl': 1-byte value representing the contents of the received HDLC control field. PassLongFrame_BASIC () PassLongFrame_BASIC is called by the LLC-interrupt server to transfer received HDLC I and UI frames to a higher layer protocol software. The LLC passes a pointer to a structure (FRAME_PASS) containing information about the received frame to PassLongFrame_BASIC. Please refer to the following paragraph for a description of this structure. Semiconductor Group 196 Low Level Controller 6.3 LLC-Code Elements 6.3.1 Structures The Structure 'ISAC' As the various routines in the LLC require facilities to store information about the device they control, the global variabel 'pt' of the type 'ISAC' has been introduced. The type 'ISAC' is a structure containing imperative information elements. These information elements are listed below:. Status Information pt_op_mode pt_state pt_ModulMode operating mode of the ISAC-S TE HDLC controller (auto-mode, nonauto mode...) Flags of 'pt_state' indicate the various device states. hardware configuration (TE or NT-S) I/O buffer related elements These elements are used when the HDLC data is transmitted or received. In both the transmit and receive directions additional RAM is required to store data on an intermediate basis. This buffer will be referred to as the data frame. Related information is stored in the following elements: Transmit buffer pointers pt_tx_start pt_tx_curr pointer to the starting point of the data frame for transmission pointer to the present byte to be sent Receive buffer pointers pt_rx_start pt_rx_curr pointer to the starting point of the receive data frame. pointer to the next free position in the receive buffer. Data byte counters pt_tx_cnt pt_rx_cnt number of bytes yet to be transmitted number of bytes currently received The following elements are used to store the type of frame: pt_rx_frame pt_tx_frame type of received frame. type of transmitted frame. Semiconductor Group 197 Low Level Controller The Structure 'FRAME_PASS' The variable 'fp' of the type FRAME_PASS is used when the LLC-interrupt server has received a valid HDLC I or UI frame. A pointer to 'fp' is passed to PassLongFrame_BASIC. FRAME_PASS contains all information about the received HDLC frame. Following elements are used: mmu_buff start of MMU buffer which is used for the temporary storage of that HDLC frame. start_of_i_data Start of the I-data field in this MMU buffer. i_data_cnt Number of bytes in the I-data field. Two_byte_cf 0 for a one byte HDLC control field, 1 for a two byte HDLC-control field. ctrl_field HDLC-control field. pei 1-byte value identifying the performed address recognition. The bits 0, 1 and 2 of 'pei' represent the bits TA, SA0 and SA1 of the ISAC-S' RSTA register. frame Type of HDLC frame; 0 = I frame, 1 = UI frame. sapi Received HDLC SAPI address byte. Bit 1 of 'sapi' is the C/R-bit value (RSTA:CR). The most significant 6 bits of 'sapi' are 0 in auto-mode, nonauto mode and transparent mode. tei Received HDLC TEI-address byte. 'tei' is 0 in auto-mode and non-auto mode. 6.3.2 Definitions and Naming Conventions Public functions are declared with an EXPORT (only for better readability). External functions are imported using an IMPORT which is the redefinition of C's 'extern'. Any function which is only used locally is declared with a LOCAL (= 'static'). 6.3.2.1 Type Definitions For reference here is a list of the type definitions used in the LLC's. type definitions meaning BYTE one byte value WORD word = two byte value FPTR far pointer to BYTE Semiconductor Group 198 Low Level Controller 6.3.2.2 Macro Definitions Error conditions and other states of the ISAC-S TE must be reported to higher layers. This reporting is realized by a few macros which are executed when such conditions are detected. These macros can be mapped to any form of message a higher layer software requires. Any kind of immediately necessary actions may be defined in those macros as well. By using such constructs the code can be kept compact and clearly readable. Layer 1 Related Status Message DECODE_L1_STATUS for L1 status (IC-channel indication) decoding. HDLC Controller Related Status and Error Messages CRC_ERROR CRC error. MISSING_ACKNOWLEDGE A 'Missing HDLC I-frame acknowledge' is generated when an acknowledge message for a previously sent I frame is outstanding and the HDLC-message transfer mode is changed from auto-mode to nonauto mode. An outstanding acknowledge is indicated by the ISAC-S TE in register STAR2 ('timer recovery status' and 'waiting for acknowledge' bits). MMU_ERROR No memory available to store incoming frame. N201_ERROR N201 error, HDLC frame is too long. PEER_REC_READY Peer receiver ready. PEER_REC_BUSY Peer receive busy. PROTOCOL_ERROR Protocol error (PCE interrupt). REC_FRAME_OVERFLOW Receive frame overflow. REC_DATA_OVERFLOW Receive data overflow (RDO interrupt). REC_ABORTED Receive aborted (RAB interrupt). TX_ACKNOWLEDGE Transmit frame acknowledge. TIN_ERROR TIN interrupt, status enquiry. TX_DATA_UNDERRUN Transmit data underrun (XDU interrupt). XMR_ERROR Transmit message repeat indication (XMR interrupt). Following macros are used when a 'timer recovery status' (register STAR2, bit TREC) is recognized. ENABLE_TREC_STATUS_CHECK enable 'timer recovery status' check procedure. DISABLE_TREC_STATUS_CHECK disable 'timer recovery status' check procedure. Semiconductor Group 199 Low Level Controller 6.4 Interrupts Int_ICC is to be called in the case of ISAC-S TE interrupts. The following interrupts are handled directly in Int_ICC: 'Transmit pool ready' interrupt (ISTA:XPR) 'Timer' interrupt (ISTA:TIN). 'Receive Status Change' interrupt (ISTA:RSC). 'Extended' interrupt (ISTA:EXI). The 'Receive Pool Full' (ISTA:RPF) and 'Receive Message End' (ISTA:RME) interrupts are handled by function RX_ICC. The 'CI or SQ channel change' interrupt (ISTA:CISQ) is handled by IntL1_SBC. Please note that the following interrupts are not handled by the interrupt service routine described here: ISTA:SIN (synchronous transfer interrupt) EXIR:SOV (synchronous transfer overflow) EXIR:MOS (monitor status) is handled by external functions which are not part of this description. EXIR:SAW (subscriber awake) EXIR:WOV (watchdog timer overflow) Semiconductor Group 200 Low Level Controller 6.5 LLC-Routine Reference 6.5.1 ISAC(R)-S TE Layer-1 Functions: The SBC Part ActL1_SBC () Initiates layer-1 activation. The appropriate CI code (activate request) is written to the CI channel if the layer 1 is not already activated. ActL1_SBC then returns with ACK_DONE. The subsequent status changes of the SBC will cause CI-channel status change (CISQ) interrupts and these will be evaluated in the layer-1 interrupt service routine IntL1_SBC. If the layer 1 is already activated nothing is carried out but ActL1_SBC calls DECODE_L1_STATUS to report the activated state. DeaL1_SBC () Initiates layer 1 deactivation. The appropriate CI code is written to the CI channel if the layer 1 is not already deactivated. The subsequent layer 1 status changes cause CI channel status change (CISQ) interrupts and these will be evaluated in the layer 1 interrupt service routine IntL1_SBC. If the layer 1 is already deactivated nothing is carried out but DeaL1_SBC calls DECODE_L1_STATUS to report the deactivated state. ArL1_SBC () Activates a local loop in the SBC. The appropriate CI code (activate request loop) is written to the SBC. ArL1_SBC returns with ACK_DONE. The subsequent status changes of the SBC will generate CISQ interrupts and these will be evaluated and reported in the layer-1 interrupt service routine IntL1_SBC. EnaClk_SBC () EnaClk_SBC enables clocking in TE configurations when the layer 1 is in power-down state. If first tests if clocks are actually there. If there are clocks the function returns with FALSE. If there are no clocks (power-down state) the power-up procedure is implemented. The SPU bit in register SPCR is set. The TIM code is written to the CI channel. EnaClk_SBC waits until the power-up state (PU) is indicated before the SPU bit is reset to 0. The routine then returns with TRUE. InitL1_SBC () Initializes and resets the layer-1 controller (ResL1_SBC). Timing mode 0 is set and the TICbus address is also programmed. Semiconductor Group 201 Low Level Controller ResL1_SBC () This routine resets the layer 1 part of an ISAC-S. It also checks that the layer 1 part is operating correctly. Reset procedure: A software reset command (RS) is sent to the layer 1 part via the IOM CI0 channel. ResL1_SBC waits for the expected new state (EI) if no timeout condition occurs and issues a release command (DIU). If the new state (EI) is not observed the ISAC-S layer 1 part will be deemed to be defective. IntL1_SBC () Interrupt Handler Handles the CISQ interrupts which indicate changes in the layer 1 status. The final confirmation of deactivation is carried out here. The actual layer 1 state is evaluated by reading register CIR0. The following is then carried out: If the CI-channel indication is 'pending deactivation' state (DR), DIU is sent to deactivate the layer 1. If the indication is an 'activation indication' (AI) the activation must be confirmed from the TE side. IntL1_SBC does it automatically by writing an 'activation request' (AR). In this way this requirement of the ISAC-S TE is transparent to the higher protocol layers. After every CI-channel status change interrupt (CISQ) DECODE_L1_STATUS is called to report the current layer-1 state. 6.5.2 ISAC(R)-S TE HDLC-Controller Related Functions: The ICC Part InitPeitab_ICC () Initializes the local variable 'pt'. InitPeitab_ICC is to be called once during the system initialization phase. InitLay2_ICC () Initializes the HDLC controller. The function arguments allow the selection of the HDLCcontroller message transfer mode (auto-mode, non-auto mode, ...), one or two byte HDLCcontrol field operation (modulo 8 or 128) and the setting of the ISAC-S TE internal hardware timer. After InitLay2_ICC is called the TEI values for a Broadcast Link are programmed (TEI = FF hex). The HDLC controller is not reset. StoreTEI_ICC () StoreTEI_ICC is used to program a TEI value in register TEI1 or TEI2 depending on the function argument value. Semiconductor Group 202 Low Level Controller StoreSAPI_ICC () StoreSAPI_ICC is used to program a SAPI value in register SAP1 or SAP2 depending on the function argument value. RecReady_ICC () Sets HDLC receiver ready or not ready depending on the function argument value. ResetHDLC_ICC () ResetHDLC_ICC resets the HDLC controller. Status flags of the local variable 'pt' indicating any on-going data transmissions or receptions are reset and memory buffers are released. SendFrame_ICC () SendFrame_ICC initiates the transmission of HDLC frames (S, U, I, UI frames). A frame can not be sent if the transmit path is still in use, i.e. if the previous transmission is not finished, if the timer recovery state is indicated (only for I frames) or if the XFIFO is blocked (STAR:XFW bit). If the transmission is begun the interrupt handler (Int_ICC) will handle subsequent tasks, for example shifting remaining data bytes into the XFIFO or calling the MMU to release the memory buffer. Loop_ICC () Switches testloop at the IOM interface on or off, i.e. connects internally the data upstream and data downstream lines. This is achieved through setting/resetting the TLP bit in register SPCR. If the layer-1 part does not deliver clocks while in the deactivated state the clocks will be enabled when the loop is switched on by means of EnableClk_BASIC. In the Siemens Low Level Controllers for BASIC access ICs EnableClk_BASIC is a function pointer which addresses EnaClk_SBC if an ISAC-S or SBC(X) is used. When the loop is switched off the layer 1 part will return to its normal deactivated state. Semiconductor Group 203 Low Level Controller Int_ICC () Interrupt Handler Evaluates and handles the ISAC-S TE interrupts. Interrupt service procedure: The bits of the interrupt status register ISTA are scanned. XPR, TIN, RSC, and EXI interrupts are handled directly by Int_ICC. For RPF and RME interrupts the function RX_ICC is called, for CISQ interrupts IntL1_SBC is called. The interrupt related actions performed are: - XPR(transmit pool ready) interrupt, but no TIN and no PCE (EXIR:PCE) interrupt: a) HDLC controller reset was given previously. b) last transmission is finished. The XFIFO will be loaded if there are more bytes to be sent. If not, a 'transmit frame acknowledge' can be generated (if depends on the message transfer mode and some other conditions). - TIN interrupt: The HDLC controller's internal timer has expired (in auto-mode only). - RSC (receiver status change of remote station) interrupt: A status change of the remote station's receiver has been detected. This is reported to the higher layers. - EXI (extended) interrupt: One of the six non-critical interrupts has been generated. The exact cause is read from register EXIR and reported to the higher layers. RX_ICC () Interrupt Handler Handles the receive pool full and receive message end (RPF and RME) interrupts if TIN and PCE (EXIR:PCE) interrupt are not indicated. Received frames are handed over to the higher software levels. Errors detected during the frame reception are reported to the higher layers. RPF interrupt: 32 data bytes are in the RFIFO. The end of the received frame is yet to be received and the message is not complete. RME interrupt: The receive message is complete. The RFIFO contains the last bytes of a frame greater than 32 bytes long or a complete frame. In the case of a long frame the beginning of this frame will already have been received using the RPF interrupt. Address and control field information is examined, the type of frame (HDLC U-, UI-, I- or S frame) is determined and the validity of the frame is checked. Finally the frame or a error condition message is sent to the higher layers. Check_TREC_status_ICC () Check_TREC_status_ICC () is called periodically by the operating system, if 'timer recovery status' (STAR2:TREC) was detected during a previous XPR interrupt handling. A 'transmit frame acknowledge' for an HDLC I frame is generated if the TREC status is left and no timer interrupt (ISTA:TIN) is indicated. Semiconductor Group 204 Low Level Controller 6.6 Listing of Driver Routines /***************************************************************************/ /* */ /* SIEMENS ISDN-Userboard (c) 1987-1993 */ /* ====================== */ /* */ /* Firmware: driver functions for ICC/ISAC-S/ISAC-P */ /* File : icc.c */ /* */ /***************************************************************************/ /* Include Files /* ============= */ */ #include "def.h" #include "basic.h" #include "message.h" /* Import Functions /* ================ */ */ /* from void void crt0.asm STRING_IN (); STRING_OUT (); */ IMPORT IMPORT /* from PEITAB basic00.c *GetPeitab_BASIC (); */ IMPORT /* from void void int basic_l1.c IntLay1_BASIC (); ResetLay1_BASIC (); EnableClk_BASIC (); */ IMPORT IMPORT IMPORT /* from void void void basic_l2.c PassLongFrame_BASIC (); Decode_S_Frame_BASIC (); Decode_U_Frame_BASIC (); */ IMPORT IMPORT IMPORT /* from int FPTR mmu.c */ IMPORT IMPORT /* from int int mofc.c IMPORT IMPORT MMU_free (); MMU_req (); */ IntMon_MOFC (); Wr_IntMon_MOFC (); /* Export Functions /* ================ EXPORT EXPORT EXPORT int void int Semiconductor Group */ */ Assign_ICC (); Check_TREC_status_ICC (); InitLay2_ICC (); 205 Low Level Controller EXPORT EXPORT EXPORT EXPORT void void int int InitPeitab_ICC (); Int_ICC (); Loop_ICC (); SwitchB_ICC (); EXPORT EXPORT EXPORT EXPORT EXPORT int int int int int RecReady_ICC (); ResetHDLC_ICC (); StoreTEI_ICC (); StoreSAPI_ICC (); SendFrame_ICC (); /* Local Functions /* =============== LOCAL void */ */ RX_ICC (); /* Variables /* ========= IMPORT unsigned int */ */ interrupt_act; /* Function Declarations /* ===================== */ */ /***************************************************************************/ /* */ /* Function: InitPeitab_ICC () */ /* Parms : '*pt' pointer to the assigned PEITAB array element */ /* 'base' address of detected ICC/ISAC */ /* purpose : initialization of the PEITAB elemtn for an ICC / ISAC-S */ /* */ /***************************************************************************/ EXPORT void InitPeitab_ICC (pt, base) register PEITAB *pt; IO_PORT base; { BYTE version; IO_PORT reg_rbch = base + ICC_RBCH; /* /* /* /* /* read the ICC/ISAC-S (ISAC-P) version number 0 for versions A1, A2, .. 1 and greater for versions 2.x [Bx] (x=1,2,3,4) and later */ */ */ */ */ version = inp (reg_rbch); if (version != 0) { if (pt->pt_device == PT_ICC) pt->pt_device = PT_ICC_B; /* and set the device identifier /* accordingly if (pt->pt_device == PT_ISAC_S) Semiconductor Group 206 */ */ Low Level Controller pt->pt_device = PT_ISAC_S_B; } pt->pt_io_base = base; pt->pt_r_fifo pt->pt_r_ista pt->pt_r_mask pt->pt_r_star pt->pt_r_cmdr pt->pt_r_mode pt->pt_r_timr pt->pt_r_exir pt->pt_r_xad1 pt->pt_r_xad2 pt->pt_r_sap1 pt->pt_r_sap2 pt->pt_r_rsta pt->pt_r_tei1 pt->pt_r_tei2 pt->pt_r_rhcr pt->pt_r_spcr pt->pt_r_stcr pt->pt_r_cixr pt->pt_r_monr pt->pt_r_adfr = = = = = = = = = = = = = = = = = = = = = base base base base base base base base base base base base base base base base base base base base base + + + + + + + + + + + + + + + + + + + + + ICC_FIFO; ICC_ISTA; ICC_MASK; ICC_STAR; ICC_CMDR; ICC_MODE; ICC_TIMR; ICC_EXIR; ICC_XAD1; ICC_XAD2; ICC_SAP1; ICC_SAP2; ICC_RSTA; ICC_TEI1; ICC_TEI2; ICC_RHCR; ICC_SPCR; ICC_STCR; ICC_CIXR; ICC_MONR; ICC_ADFR; pt->pt_r_rbcl pt->pt_r_rbch pt->pt_r_mox1 pt->pt_r_mocr pt->pt_r_cix1 pt->pt_r_adf2 = = = = = = base base base base base base + + + + + + ICC_RFBC; ICC_RBCH; ICC_MOX1; ICC_MOCR; ICC_CIX1; ICC_ADF2; pt->pt_r_rfbc pt->pt_r_sfcr pt->pt_r_sscx = base + ICC_RFBC; = base + ICC_SFCR; = base + ICC_SSGX; pt->pt_r_sqxr = base + ISAC_SQXR; /* store the base (IO) address */ /* /* /* /* */ */ */ */ the following structure elements store the register IO addresses (e.g. for FIFOs, ISTA, MASK, etc.) /* = CIX0/CIR0 in later versions /* = MOX0/MOR0 in later versions /* = ADF1 in later versions */ */ */ /* = RBCL in later version */ /* = MOSR (read access) /* CIX1 and CIR1 register */ */ /* S/Q channel transmit and /* receive register */ */ /* STAR2 register */ pt->pt_r_star2 = base + ICC_STR2; DISABLE_TREC_STATUS_CHECK (); } /***************************************************************************/ /* */ /* Function : InitLay2_ICC () */ /* Parameters: */ /* */ Semiconductor Group 207 Low Level Controller /* 'pei' 0x00 D-channel controller */ /* 0x40 B-channel controller (A) */ /* 0x80 B-channel controller (B) */ /* */ /* 'modulo' 0 modulo 8 operation */ /* 1 modulo 128 operation */ /* */ /* 'mode' operating mode. (automode, non automode, etc.) */ /* */ /* 'tim_mode' value for the TIMR register (valid in auto mode only) */ /* refer to the description of that register in the */ /* data sheets. */ /* */ /* Purpose: Initialization of an ICCs (ISAC-..) HDLC controller part. */ /* After execution of InitLay2_ICC, the TEI values for */ /* the Broadcast Link are programmed. */ /* */ /* Note: No HDLC controller reset is done. */ /* Only two byte address fields are supported */ /* */ /* If the ICC (ISAC) is reprogrammed from AUTOMODE to NON - AUTOMODE */ /* the successful transmission and acknowledgement of an I-frame */ /* currently sent is not assured. */ /* Switching from AUTOMODE to NON AUTOMODE causes an I frame to be */ /* transmitted completely by the ICC. But the transmit acknowledge */ /* (XPR interrupt) in NON AUTOMODE only indicates that the ICC has */ /* sent the frame out of its XFIFO. It indicates not the successful */ /* transmission of the I-frame as it is in AUTOMODE (timer super*/ /* vision, polling for acknowledge frames)! */ /* Therefore if an I-frame is outstanding and the mode is changed */ /* from AUTOMODE to NON-AUTOMODE MISSING_ACKNOWLEDGE is called to */ /* generate a warning message. */ /* MISSING_ACKNOWLEDGE is also called if 'timer recovery' status */ /* (TREC) or 'waiting for acknowledge (WFA)' is indicated. */ /* */ /***************************************************************************/ EXPORT int InitLay2_ICC (pei, modulo, mode, tim_mode) BYTE pei, modulo, mode, tim_mode; { BYTE mode_reg; register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) /* request pointer to the /* corresponding PEITAB table /* element */ */ */ /* no interrupts during init. */ return (ACK_NOT_SUPPORTED); if (modulo != 0 && modulo != 1) return (ACK_WRONG_PARM); outp (pt->pt_r_mask, 0xFF); mode_reg = inp (pt->pt_r_mode) & (MODE_HMD2 | MODE_HMD1 | MODE_HMD0); switch (mode) Semiconductor Group /* select OPERATING MODE 208 */ Low Level Controller { /* ******************* case PT_MD_AUTO: /* HDLC AUTO MODE /* full address recognition, /* internal timer mode, receiver /* active, 2 bytes address fields /* are selected. mode_reg |= (MODE_TMD | MODE_RAC | MODE_ADM); outp (pt->pt_r_timr, tim_mode); break; case PT_MD_NON_AUTO: mode_reg /* HDLC NON AUTO MODE /* full address recognition, /* receiver active, 2 byte address /* fields |= (MODE_MDS0 | MODE_RAC | MODE_ADM); */ */ */ */ */ */ */ */ */ */ if (((pt->pt_op_mode == PT_MD_AUTO) && (pt->pt_state & PT_TX_ACTIVE) && (pt->pt_tx_frame == PT_FR_I)) || (inp(pt->pt_r_star2) & (STAR2_TREC | STAR2_WFA))) { MISSING_ACKNOWLEDGE (pei); ResetHDLC_ICC (pei); } outp (pt->pt_r_timr, 0); break; case PT_MD_TRANSP: mode_reg break; /* TRANSPARENT MODE /* SAPI-address (high-byte) /* recognition |= (MODE_MDS1 | MODE_MDS0 | MODE_RAC | MODE_ADM); case PT_MD_EXT_TRANSP: case PT_MD_CLEAR_EXT: mode_reg break; /* EXTENDED TRANSPARENT MODE /* as well as clear mode /* no address recognition |= (MODE_MDS1 | MODE_MDS0 | MODE_RAC); */ */ */ */ */ */ default: outp (pt->pt_r_mask, 0x00); return (ACK_WRONG_PARM); } pt->pt_op_mode = mode; /* save MODE register settings /* modulo: 1 (mod 128); 0 (mod 8) outp (pt->pt_r_sap2, (BYTE) (modulo ? 0x02 : 0x00)); outp (pt->pt_r_tei2, 0xFF); if (modulo) pt->pt_state |= PT_M128; else pt->pt_state &= ~PT_M128; outp (pt->pt_r_mode, mode_reg); Semiconductor Group 209 */ */ Low Level Controller outp (pt->pt_r_mask, 0x00); return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: StoreTEI_ICC () */ /* Parms : 'pei', 'tei' and 'reg2' */ /* purpose : program TEI in register TEI1 (reg2 = 0) or TEI2 (reg2 = 0) */ /* */ /***************************************************************************/ EXPORT int StoreTEI_ICC (pei, tei, reg2) BYTE pei, tei, reg2; { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); if (reg2 == 1) outp (pt->pt_r_tei2, tei); else { outp (pt->pt_r_xad2, tei); outp (pt->pt_r_tei1, tei); } return (ACK_DONE); /* store TEI in register TEI2 */ /* store TEI in register TEI1 */ } /***************************************************************************/ /* */ /* Function: StoreSAPI_ICC () */ /* Parms : pei, sapi, reg2 */ /* purpose : store SAPI in register SAPI1 (reg2 = 0) or SAPI2 */ /* (reg2 = 0) */ /* */ /***************************************************************************/ EXPORT int StoreSAPI_ICC (pei, sapi, reg2) BYTE pei, sapi, reg2; { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); sapi &= ~0x03; if (reg2 == 1) /* store SAPI in SAP2 */ outp (pt->pt_r_sap2, sapi | ((pt->pt_state & PT_M128) ? 0x02 : 0x00)); else { /* store SAPI in SAP1 */ outp (pt->pt_r_xad1, sapi); if ((pt->pt_ModulMode == PT_MM_NT) || (pt->pt_ModulMode == PT_MM_LT_S)) sapi |= 0x02; Semiconductor Group 210 Low Level Controller outp (pt->pt_r_sap1, sapi); } return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: RecReady_ICC () */ /* Parms : pei, ready */ /* purpose : set HDLC receiver ready ('ready'= 1) */ /* not ready ('ready'= 0) */ /* To be used in auto mode only */ /* */ /***************************************************************************/ EXPORT int RecReady_ICC (pei, ready) BYTE pei, ready; { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); outp (pt->pt_r_cmdr, (BYTE) (ready ? 0x00 : CMDR_RNR)); return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: ResetHDLC_ICC () */ /* Parms : pei */ /* purpose : reset HDLC controller */ /* */ /***************************************************************************/ EXPORT int ResetHDLC_ICC (pei) BYTE pei; { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); outp (pt->pt_r_mask, 0xFF); /* /* /* /* /* /* clear receive and transmit paths, i.e. clear the status variables indicating any transmission or reception of frames and release the MMU buffers FREE_TX_PATH (pt->pt_pei); if (pt->pt_rx_start) { MMU_free (pt->pt_rx_start); pt->pt_rx_start = NULL_PTR; Semiconductor Group 211 */ */ */ */ */ */ Low Level Controller pt->pt_state pt->pt_rx_frame pt->pt_rx_cnt &= ~PT_REC_ACTIVE; = 0x00; = 0; } pt->pt_state &= ~PT_REC_ACTIVE; /* /* /* /* /* set the reset flag in the state variable. This allows the interrupt service routine to react correctly on the following XPR interrupt */ */ */ */ */ pt->pt_state |= PT_HDLC_RESET; /* the reset commands: */ /* - receive message complete (RME) */ /* - reset hdlc receiver (RHR) */ /* - transmitter reset (XRES)*/ outp (pt->pt_r_cmdr, CMDR_RMC | CMDR_RHR | CMDR_XRES); if (pt->pt_op_mode == PT_MD_AUTO) /* write TIMR register to stop the /* internal timer in automode outp (pt->pt_r_timr, inp(pt->pt_r_timr)); outp (pt->pt_r_mask, 0); return (ACK_DONE); /* now allow all interrupts again */ */ */ } /***************************************************************************/ /* */ /* Function: SendFrame_ICC () */ /* Parms : 'pei' */ /* 'frame_type' specifying the frame */ /* 'cnt' number of bytes to send */ /* 'frame_ptr' pointer to the data bytes */ /* */ /* purpose : Initiate transmission of HDLC frames ( S, U, I, UI ) */ /* */ /***************************************************************************/ EXPORT int SendFrame_ICC (pei, frame_type, cnt, frame_ptr) BYTE pei, frame_type; WORD cnt; FPTR frame_ptr; { register PEITAB *pt; BYTE cmd; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); /* return if XFIFO is not write /* enable */ */ /* return if transmit path still /* blocked and not in automode */ */ if (!(inp (pt->pt_r_star) & 0x40)) return (ACK_ACCESS_FAULT); Semiconductor Group 212 Low Level Controller if (pt->pt_state & PT_TX_ACTIVE && pt->pt_op_mode != PT_MD_AUTO) return (ACK_ACCESS_FAULT); if (pt->pt_op_mode == PT_MD_AUTO) { /* it is not allowed to send an I /* frame in the timer recovery /* or in waiting_for_acknowledge /* status if (inp(pt->pt_r_star2) & (STAR2_TREC | STAR2_WFA)) if (frame_type == PT_FR_I) return (ACK_ACCESS_FAULT); */ */ */ */ if (inp(pt->pt_r_star2) & STAR2_WFA) if (pt->pt_state & PT_TX_MMU_FREE) { MMU_free (pt->pt_tx_start); pt->pt_state &= ~PT_TX_MMU_FREE; } } pt->pt_state |= PT_TX_ACTIVE; pt->pt_tx_start = frame_ptr; pt->pt_tx_frame = frame_type; /* transmitter is active /* store data frame pointer /* and frame type */ */ */ if (cnt <= 32) { /* if the number of bytes is <=32 /* the frame can be shifted /* completely into the XFIFO STRING_OUT (frame_ptr, pt->pt_r_fifo, cnt); pt->pt_tx_cnt = 0; */ */ */ } else { /* if the number of bytes is /* greater 32 the first 32 are /* shifted into the XFIFO, the /* remaining are sent later /* (interrupt service routine) STRING_OUT (frame_ptr, pt->pt_r_fifo, 32); pt->pt_tx_cnt = cnt - 32; pt->pt_tx_curr = frame_ptr + 32; */ */ */ */ */ } /* /* /* /* /* /* /* /* compute the command byte for the CMDR register: in automode the 'transmit I frame' command must be used when it is an HDLC I frame. The 'transmit transparent frame' command must be used in all other cases if (pt->pt_op_mode == PT_MD_AUTO) { cmd = (pt->pt_tx_frame == PT_FR_I) ? CMDR_XIF : CMDR_XTF; Semiconductor Group 213 */ */ */ */ */ */ */ */ Low Level Controller if (inp (pt->pt_r_star) & CMDR_RNR) cmd |= CMDR_RNR; } else cmd = CMDR_XTF; /* When the frame fits completely /* into the XFIFO the XME command /* must be given */ */ */ /* now output the command byte to /* the CMDR register */ */ if (!pt->pt_tx_cnt) cmd |= CMDR_XME; outp (pt->pt_r_cmdr, cmd); /* UI frame sent while waiting for /* ackowledge in automode (an ID /* check response UI frame) /* The flag is checked by the /* interrupt service routine when /* handling the next XPR interrupt. if (inp(pt->pt_r_star2) & STAR2_WFA && pt->pt_op_mode == PT_MD_AUTO && frame_type == PT_FR_UI) pt->pt_state |= UI_SENT_WHILE_WAITING_FOR_ACK; */ */ */ */ */ */ return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: Loop_ICC () */ /* Parms : 'pei' */ /* 'on' 1 -> test-loop on */ /* 0 -> test-loop off */ /* purpose: switch testloop at the IOM interface on/off */ /* */ /***************************************************************************/ EXPORT int Loop_ICC (pei, on) BYTE pei; BOOLEAN on; { PEITAB *pt_dch; BYTE r_spcr; register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); pt_dch = GetPeitab_BASIC (0); if (on) { pt->pt_state |= PT_LOOP; /* Loop ON */ /* enable clocks in TE mode */ if (pt->pt_ModulMode == PT_MM_TE) Semiconductor Group 214 Low Level Controller { /* dummy value in the cixr register */ /* prevents a false interpretation of*/ /* the incoming (looped) C/I channel */ if (EnableClk_BASIC (pt_dch)) outp (pt_dch->pt_r_cixr, 0x6F); } r_spcr = inp (pt->pt_r_spcr); outp (pt->pt_r_spcr, r_spcr | SPCR_TPL); } else /* Loop OFF { r_spcr = inp (pt->pt_r_spcr) & ~SPCR_TPL; outp (pt->pt_r_spcr, r_spcr); */ pt->pt_state &= ~PT_LOOP; } return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: SwitchB_ICC () */ /* purpose : switch the B-channels in IOM1 configurations */ /* to the SSI or SLD interface or back to network */ /* */ /***************************************************************************/ EXPORT int SwitchB_ICC (pei, chan_ctrl, sip_act) BYTE pei, chan_ctrl; BOOLEAN sip_act; { register PEITAB *pt; BYTE r_spcr; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); if (chan_ctrl > 0x0F) return (ACK_WRONG_PARM); if (!(pt->pt_state & PT_IOM2)) { r_spcr = inp (pt->pt_r_spcr) & 0xF0; if (sip_act) r_spcr |= SPCR_SAC; else r_spcr &= ~SPCR_SAC; /* activate SIP ? /* yes: set SAC bit */ */ /* */ no: clear SAC bit outp (pt->pt_r_spcr, r_spcr | chan_ctrl); } return (ACK_DONE); } Semiconductor Group 215 Low Level Controller /* *** The interrupt service routines *** */ /************************************************************************/ /***************************************************************************/ /* */ /* Function: Int_ICC () */ /* Parms :'pt' pointer to the corresponding PEITAB-table element */ /* purpose : handle ICC (ISAC-S, ISAC-P) interrupts */ /* Int_ICC is called from IntServ_BASIC in basic_l2.c which */ /* is SIPB system specific. */ /* */ /***************************************************************************/ EXPORT void Int_ICC (pt) register PEITAB *pt; { WORD cnt; BYTE exir, cmd; register BYTE ista; if (!(ista = inp (pt->pt_r_ista))) return; exir = inp (pt->pt_r_exir); /* XPR interrupt /* ============= /* the XPR interrupt indicates /* that the XFIFO is ready for new /* data bytes. /* Reasons: /* - HDLC controller reset /* (CMDR:XRES) /* - data transmission finished if ((ista & ISTA_XPR) && !(ista & ISTA_TIN) && !(exir & EXIR_PCE)) { /* transmit byte count is 0 /* -----------------------if ((cnt = pt->pt_tx_cnt) == 0) { /* HDLC controller reset command /* given previously ? /* ----------------------------/* do nothing when it was a HDLC /* controller reset only the /* indicating flag must be cleared if (pt->pt_state & PT_HDLC_RESET) pt->pt_state &= ~PT_HDLC_RESET; else { /* XPR was generated because the /* last transmission is finished /* -----------------------------/* AUTOMODE operation ? Semiconductor Group 216 */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ */ Low Level Controller if (pt->pt_op_mode == PT_MD_AUTO) { /* UI frame sent while waiting for /* I frame acknowledge ? if (pt->pt_state & UI_SENT_WHILE_WAITING_FOR_ACK) { /* the UI frame was sent out if the /* XFIFO is empty (write enable) if (inp(pt->pt_r_star) & STAR_XFW) TX_ACKNOWLEDGE (pt->pt_pei, pt->pt_tx_frame); */ */ */ */ pt->pt_state &= ~UI_SENT_WHILE_WAITING_FOR_ACK; /* if we are in timer recovery /* status the TREC status check /* procedure is activated. The /* transmit acknowledge for the I /* frame must not be generated !!! if (inp (pt->pt_r_star2) & STAR2_TREC) ENABLE_TREC_STATUS_CHECK (); else TX_ACKNOWLEDGE (pt->pt_pei, (BYTE) PT_FR_I); */ */ */ */ */ } else { /* if we are in timer recovery /* status and the last frame was an /* I frame the TREC status check /* procedure is activated. /* If not an transmit acknowledge /* is generated if (pt->pt_tx_frame == PT_FR_I && (inp (pt->pt_r_star2) & STAR2_TREC)) ENABLE_TREC_STATUS_CHECK (); else TX_ACKNOWLEDGE (pt->pt_pei, pt->pt_tx_frame); */ */ */ */ */ */ /* In all other operating modes /* (non automode, transparent mode, /* ...) the transmit acknowledge /* can be generated at once. TX_ACKNOWLEDGE (pt->pt_pei, pt->pt_tx_frame); */ */ */ */ } } else /* /* /* /* /* transmit byte count and status flag are reset and any MMU buffer used for temporary transmit data storage is released if necessary pt->pt_tx_cnt = 0; pt->pt_state &= ~PT_TX_ACTIVE; if (pt->pt_state & PT_TX_MMU_FREE) { MMU_free (pt->pt_tx_start); Semiconductor Group 217 */ */ */ */ */ Low Level Controller pt->pt_state &= ~PT_TX_MMU_FREE; } } } else { /* transmit count is not 0 /* more data to be sent ! /* -----------------------if (pt->pt_op_mode == PT_MD_AUTO) cmd = (pt->pt_tx_frame ? CMDR_XTF : CMDR_XIF) | (inp(pt->pt_r_star) & CMDR_RNR); else cmd = CMDR_XTF; /* less than 32 bytes left ? */ */ */ */ if (pt->pt_tx_cnt <= 32) { /* shift all bytes into the XFIFO /* and give XME command STRING_OUT (pt->pt_tx_curr, pt->pt_r_fifo, cnt); pt->pt_tx_cnt = 0; outp (pt->pt_r_cmdr, cmd | CMDR_XME); } else { /* more than 32 bytes are left to /* be sent; write 32 into the XFIFO STRING_OUT (pt->pt_tx_curr, pt->pt_r_fifo, 32); outp (pt->pt_r_cmdr, cmd); /* give the transmit command, pt->pt_tx_curr += 32; /* update current buffer pointer pt->pt_tx_cnt -= 32; /* and counter of remaining bytes */ */ */ */ */ */ */ } } } if (ista & ISTA_TIN) { /* TIN interrupt /* ============= /* ResetHDLC_ICC (pt->pt_pei); */ */ */ /* /* /* /* /* */ */ */ */ */ DISABLE_TREC_STATUS_CHECK (); TIN_ERROR (pt->pt_pei); } HDLC receiver interrupt ? ========================= (receive pool full or receive message end and not PCE and not TIN) if ((ista & (ISTA_RPF | ISTA_RME)) && !(exir & EXIR_PCE) && !(ista & ISTA_TIN)) RX_ICC (ista & ISTA_RPF, pt); /* /* /* /* /* /* Semiconductor Group status change of the remote station's receiver (i.e. RR or RNR received). The status can be determined by reading the RRNR bit of register STAR 218 */ */ */ */ */ */ Low Level Controller if (ista & ISTA_RSC) { if (inp (pt->pt_r_star) & 0x10) PEER_REC_BUSY (pt->pt_pei); else PEER_REC_READY (pt->pt_pei); } /* peer receiver busy */ /* peer receiver ready */ /* B (2.x) versions of L1 device */ /* controllers can't prevent CIC bit*/ /* being set even when masked. */ /* CIC interrupt ? (layer 1 device */ /* status change) */ if ((ista & ISTA_CIC) && !interrupt_act) IntLay1_BASIC (pt); if (ista & ISTA_EXI) { /* Extended interrupt ? /* ================== /* transmit message repeat int. ? if ((exir & EXIR_XMR) && !(exir & EXIR_PCE) && !(ista & ISTA_TIN)) { XMR_ERROR (pt->pt_pei); FREE_TX_PATH (pt->pt_pei); } */ */ */ if (exir & EXIR_XDU) /* transmit data underrun ? { TX_DATA_UNDERRUN (pt->pt_pei); FREE_TX_PATH (pt->pt_pei); } */ if (exir & EXIR_PCE) { /* protocol error interrupt ? */ /* ResetHDLC_ICC (pt->pt_pei); */ /* receive frame overflow int. ? */ PROTOCOL_ERROR (pt->pt_pei); } if (exir & EXIR_RFO) { MMU_free (pt->pt_rx_start); pt->pt_rx_start pt->pt_state pt->pt_rx_frame pt->pt_rx_cnt = &= = = NULL_PTR; ~PT_REC_ACTIVE; 0; 0; REC_FRAME_OVERFLOW (pt->pt_pei); } if (exir & EXIR_MOR) if (interrupt_act) IntMon_MOFC (); else Wr_IntMon_MOFC (); Semiconductor Group /* MON channel interrupt ? 219 */ Low Level Controller } } /***************************************************************************/ /* */ /* Function: RX_ICC () */ /* Parms : 'pt' pointer to the assigned PEITAB array element */ /* 'rpf' = 1 if RPF interrupt */ /* purpose : handle interrupts generated by the receiver of an */ /* ICC (ISAC-S, ISAC-P) */ /* */ /***************************************************************************/ LOCAL void RX_ICC (rpf, pt) BOOLEAN rpf; register PEITAB *pt; { WORD RecCnt, ctrl; FPTR ptr; BYTE pei = pt->pt_pei; BYTE rsta, tei, sapi, frame_status = VALID; BOOLEAN Two, AutoM, CR_of_I_valid = TRUE; /* /* /* /* /* /* RPF interrupt: 32 bytes of a frame longer than 32 bytes have been received and are now available in the RFIFO. The message is not complete. */ */ */ */ */ */ /* /* /* /* /* /* RME interrupt: Receive message end. The RFIFO contains a complete frame (length <= 32 byte) or the last bytes or a frame (length > 32) ================================ */ */ */ */ */ */ if (rpf) RecCnt = 32; else { /* read byte count register(s) to /* get the number of currently /* received bytes /* please note that ICC / ISAC-S /* version Axx had only one byte /* count register !!! if (pt->pt_device == PT_ICC || pt->pt_device == PT_ISAC_S) RecCnt = (BYTE) inp (pt->pt_r_rfbc); else RecCnt = (WORD) inp (pt->pt_r_rbcl) | (WORD) (inp (pt->pt_r_rbch) & 0x0F) << 8; */ */ */ */ */ */ if (RecCnt && !(RecCnt &= 0x1F)) RecCnt = 32; } /* 'RecCnt' now contains the number */ /* of bytes actually received */ Semiconductor Group 220 Low Level Controller /* was receiver active before or is */ /* the RPF/RME for a new incoming */ /* frame ? */ if (!(pt->pt_state & PT_REC_ACTIVE)) { if (RecCnt > 0) { if (rpf) pt->pt_rx_curr = pt->pt_rx_start = MMU_req (266); else pt->pt_rx_curr = pt->pt_rx_start = MMU_req (38); if (pt->pt_rx_start == NULL_PTR) { MMU_ERROR (pei); pt->pt_rx_frame = PT_FR_NO_MEMORY; } } pt->pt_state |= PT_REC_ACTIVE; pt->pt_rx_cnt = RecCnt; } else /* if data has been already /* received only the receive byte /* counter must be updated */ */ */ pt->pt_rx_cnt += RecCnt; /* automode and frame greater /* 260 byte and automode link ? if (pt->pt_op_mode == PT_MD_AUTO && pt->pt_rx_cnt > 260 && ((inp (pt->pt_r_rsta) & 0x0D) == 9)) { pt->pt_rx_frame = PT_FR_OVERFLOW; /* /* /* /* /* ICC B4, ISAC-S B3 reset the receiver if incoming frame exceeds 528 byte I field length -> unbounded frame if (rpf && pt->pt_rx_cnt > 528) { outp (pt->pt_r_cmdr, CMDR_RHR); MMU_free (pt->pt_rx_start); pt->pt_rx_start pt->pt_state pt->pt_rx_frame pt->pt_rx_cnt = &= = = NULL_PTR; ~PT_REC_ACTIVE; 0x00; 0; N201_ERROR (pei); return; } Semiconductor Group 221 */ */ */ */ */ */ */ Low Level Controller } else if (pt->pt_rx_cnt > 266) pt->pt_rx_frame = PT_FR_OVERFLOW; /* read the bytes from the RFIFO /* if no error was detected if (pt->pt_rx_frame < PT_FR_ERROR) { if (RecCnt) { STRING_IN (pt->pt_rx_curr, pt->pt_r_fifo, RecCnt); pt->pt_rx_curr += RecCnt; /* update buffer pointer } /* it points to the next free /* location in the buffer } if (rpf) /* return when it was a RPF int. { outp (pt->pt_r_cmdr, CMDR_RMC | (inp (pt->pt_r_star) & CMDR_RNR)); return; } */ */ */ */ */ */ /* RME interrupt handling !!! /* ========================== */ */ /* the receive status byte is in /* register RSTA */ */ rsta = inp (pt->pt_r_rsta); /************************************************************************/ /* It follows a scanning section to get some information about the */ /* received data: */ /* - Performed address recognition */ /* - SAPI ('sapi'), TEI ('tei') and control field byte(s) ('ctrl') */ /* as well as the type of frame (HDLC U, UI, S or I frame) are */ /* determined. */ /* In addition the length of a frame is checked. */ /************************************************************************/ pei AutoM tei sapi ptr /* set 'pei' according to performed */ /* address recognition */ |= ((rsta & 0x0C) >> 1) | (rsta & 0x01); = FALSE; = 0; = rsta & 0x02; /* get the C/R bit value */ = pt->pt_rx_start; switch (pt->pt_op_mode) /* /* /* /* now get additional information (TEI, SAPI, control field) It depends on the selected operating mode */ */ */ */ { case PT_MD_CLEAR_EXT: Semiconductor Group /* no address recognition, /* no firmware interaction 222 */ */ Low Level Controller pt->pt_rx_frame = PT_FR_TR; ctrl = 0x00L; break; case PT_MD_EXT_TRANSP: /* no address recognition, SAPI /* and TEI are the first two bytes /* of data */ */ */ /* high byte address recognition, /* TEI is the first byte read */ */ /* read TEI and control field */ if (pt->pt_rx_cnt > 0) pt->pt_rx_cnt--; sapi = *ptr++; case PT_MD_TRANSP: if (pt->pt_rx_cnt < 2) frame_status = MUTILATED; else pt->pt_rx_cnt -= 2; tei ctrl = *ptr++; = (WORD) *ptr++; if (pt->pt_op_mode == PT_MD_TRANSP) pei |= 0x20; else pei |= 0x30; break; case PT_MD_AUTO: case PT_MD_NON_AUTO: /* full address recognition in /* AUTO/nonAUTOMODE read only the /* HDLC control field information if (pt->pt_op_mode == PT_MD_AUTO) /* AUTOMODE link ??? AutoM = ((rsta & 0x0D) == 0x09) ? TRUE : FALSE; */ */ */ */ if (!AutoM) pei |= 0x10; /* the (first byte of the) control /* field is in register RHCR ctrl = (WORD) inp (pt->pt_r_rhcr); break; */ */ } switch (ctrl & 0x03) { case 0x3: Two = FALSE; /* determine the frame type /* ======================== /* *** HDLC U frame ** */ */ */ /* one byte control field ! */ if (pt->pt_rx_cnt == 0) { pt->pt_rx_frame = PT_FR_U; break; Semiconductor Group 223 Low Level Controller } else /* pt->pt_rx_frame = PT_FR_UI;/* /* /* /* break; case 0x1: as can be seen here U frames with I field are always treated as UI frames regardless whether it's an real UI frame or an erroneous (= too long) U frame /* *** HDLC S-Frame ** /* two byte control field ? if ((Two = (pt->pt_state & PT_M128))) { ctrl <<= 8; ctrl |= (WORD) *ptr++; if (pt->pt_rx_cnt > 0) pt->pt_rx_cnt--; else /* Second byte of the two byte /* control field is missing ! frame_status = MUTILATED; */ */ */ */ */ */ */ */ */ } if (pt->pt_rx_cnt > 0) frame_status = TOO_LONG; /* S frame with I-field ! */ /* *** HDLC I frame ** */ pt->pt_rx_frame = PT_FR_S; break; case 0x2: case 0x0: /* no address recognition if (pt->pt_op_mode == PT_MD_CLEAR_EXT) { pt->pt_rx_frame = PT_FR_TR; break; } */ Two = (pt->pt_state & PT_M128); pt->pt_rx_frame = PT_FR_I; /* C/R bit of received I frame /* valid (=1) in TE configuration ? /* If 'CR_of_I_valid' is FALSE the /* automatic acknowledge of an /* I frame in Automode is /* prevented! A protocol software /* will receive the PROTOCOL_ERROR /* message and re-establish the /* link. if (AutoM && !(sapi & 0x02) && (pt->pt_ModulMode == PT_MM_TE)) CR_of_I_valid = FALSE; if (AutoM) break; Semiconductor Group 224 */ */ */ */ */ */ */ */ */ Low Level Controller if (Two) /* two byte control field ? { if (pt->pt_rx_cnt == 0) frame_status = MUTILATED; */ if (pt->pt_rx_cnt > 0) pt->pt_rx_cnt--; ctrl <<= 8; ctrl |= (WORD) *ptr++; } break; } if (pt->pt_rx_cnt > 260) /* I part greater than 260 ? */ { pt->pt_rx_frame = PT_FR_OVERFLOW; N201_ERROR(pei); /* must reset the controller */ outp (pt->pt_r_cmdr, CMDR_RMC | CMDR_RHR | CMDR_XRES); outp (pt->pt_r_timr, inp(pt->pt_r_timr)); pt->pt_state |= PT_HDLC_RESET; FREE_TX_PATH (pt->pt_pei); } else if (!CR_of_I_valid) /* C/R of I frame invalid in TE ? */ { /* prevent acknowledging S-frame */ /* beeing sent and create */ /* PROTOCOL_ERROR message. */ pt->pt_rx_frame = PT_FR_FAULT; PROTOCOL_ERROR (pt->pt_pei); /* must reset the controller */ outp (pt->pt_r_cmdr, CMDR_RMC | CMDR_RHR | CMDR_XRES); outp (pt->pt_r_timr, inp(pt->pt_r_timr)); pt->pt_state |= PT_HDLC_RESET; FREE_TX_PATH (pt->pt_pei); } else /* enter 'RMC' command if not */ outp (pt->pt_r_cmdr, CMDR_RMC | (inp (pt->pt_r_star) & CMDR_RNR)); /************************************************************************/ /* */ /* Now all information about the received frame is available: */ /* - performed address recognition or TEI and SAPI values. */ /* - HDLC control field */ /* - type of frame (HDLC U, UI, S, I frame). */ /* - info about the validity of the frame */ /* */ /************************************************************************/ if (rsta = (rsta & (RSTA_RDO | RSTA_CRC | RSTA_RAB)) ^RSTA_CRC) pt->pt_rx_frame = PT_FR_FAULT; switch (pt->pt_rx_frame) Semiconductor Group 225 Low Level Controller { case PT_FR_FAULT: if (rsta & RSTA_RDO) REC_DATA_OVERFLOW (pei); if (rsta & RSTA_RAB) REC_ABORTED (pei); if (rsta & RSTA_CRC) CRC_ERROR (pei); /* CRC has already been inverted */ break; case PT_FR_S: /* /* /* /* Decode_S_Frame_BASIC (pei, sapi, ((pt->pt_state MMU_free (pt->pt_rx_start); break; HDLC S frame ? */ ============== */ extra parameter for 1 byte */ address field set to FALSE */ tei, ctrl, frame_status, & PT_M128) ? 0x01 : 0x00), FALSE); case PT_FR_U: HDLC U frame ? ============== extra parameter for 1 byte address field set to FALSE tei, (BYTE) ctrl, FALSE); /* /* /* /* Decode_U_Frame_BASIC (pei, sapi, MMU_free (pt->pt_rx_start); break; case PT_FR_UI: case PT_FR_I: case PT_FR_TR: /* HDLC UI or I frame ? /* ==================== /* ==================== */ */ */ */ */ */ */ if (pt->pt_rx_frame < PT_FR_ERROR) { FRAME_PASS fp; fp.mmu_buff fp.start_of_i_data fp.i_data_cnt fp.Two_byte_cf fp.ctrl_field fp.pei fp.frame fp.sapi fp.tei = = = = = = = = = pt->pt_rx_start; ptr; pt->pt_rx_cnt; Two; ctrl; pei; pt->pt_rx_frame | frame_status; sapi; tei; /* transfer the frame to the 'long /* frame queue' */ */ PassLongFrame_BASIC (&fp); } break; } /* end of 'switch (pt->pt_rx_frame)' ------------------------------- */ Semiconductor Group 226 Low Level Controller /* release the data buffer if the /* frame reception or the frame /* were erroneous */ */ */ if (pt->pt_rx_frame >= PT_FR_ERROR) MMU_free (pt->pt_rx_start); pt->pt_rx_start pt->pt_state pt->pt_rx_frame pt->pt_rx_cnt = &= = = NULL_PTR; ~PT_REC_ACTIVE; 0x00; 0; } /***************************************************************************/ /* */ /* Function: Check_TREC_status_ICC () */ /* Parms : */ /* purpose : called periodically if timer recovery status was detected */ /* during previous XPR interrupt handing. A */ /* transmit-acknowledge for I frame is generated if the TREC */ /* status is left. */ /* */ /***************************************************************************/ EXPORT void Check_TREC_status_ICC () { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (0))) return; outp (pt->pt_r_mask, ~MASK_TIN); /* allow only TIN interrupts /* timer recovery status left ? if (!(inp(pt->pt_r_star2) & STAR2_TREC)) { if (inp(pt->pt_r_ista) & ISTA_TIN) { ResetHDLC_ICC (pt->pt_pei); TIN_ERROR (pt->pt_pei); } else /* generate a transmit acknowledge /* I frame if there was no TIN /* interrupt TX_ACKNOWLEDGE (pt->pt_pei, (BYTE) PT_FR_I); DISABLE_TREC_STATUS_CHECK (); } outp (pt->pt_r_mask, 0x00); } Semiconductor Group 227 */ */ */ */ */ Low Level Controller /***************************************************************************/ /* */ /* SIEMENS ISDN-Userboard (c) 1987-1993 */ /* ====================== */ /* */ /* Firmware: driver functions for SBC / L1 part of ISAC-S */ /* File : sbc.c */ /* */ /***************************************************************************/ /* Include Files /* ============= */ */ #include "def.h" #include "basic.h" #include "message.h" /* CI codes for SBC and ISAC-S PM */ /*********************************************************/ #define #define #define #define #define #define #define #define #define CI_PU CI_TIM CI_AI CI_AR CI_DIU CI_DID CI_DR CI_RS CI_EI (BYTE)0x1C (BYTE)0x00 (BYTE)0x30 (BYTE)0x20 (BYTE)0x3C (BYTE)0x3C (BYTE)0x00 (BYTE)0x04 (BYTE)0x18 /* /* /* /* /* /* /* /* /* 0111 0000 1100 1000 1111 1111 0000 0001 0110 /* Imported Functions /* ================== */ */ */ */ */ */ */ */ */ */ */ IMPORT IMPORT /* from WORD void IMPORT /* from basic00.c PEITAB *GetPeitab_BASIC (); crt0.asm ENTERNOINT (); LEAVENOINT (); */ /* Export Functions /* ================ */ */ */ EXPORT EXPORT EXPORT EXPORT EXPORT int int int int void InitL1_SBC (); ActL1_SBC (); ArlL1_SBC (); DeaL1_SBC (); IntL1_SBC (); EXPORT EXPORT int int ResL1_SBC (); EnaClk_SBC (); Semiconductor Group PU indication timing requested activation indication activation request deactivation ind. upstream deactivation ind. downst. deactivation request Reset Error indicate downstream 228 Low Level Controller /* Variables /* ========= */ */ /* Function Declaration /* ==================== */ */ /***************************************************************************/ /* */ /* Function: EnaClk_SBC () */ /* Parms : pointer to PEITAB table element */ /* purpose : enable clocks for TE configurations */ /* */ /***************************************************************************/ EXPORT int EnaClk_SBC (pt) register PEITAB *pt; { unsigned int count, i = 0; BYTE BitSet, spcr; /* Test to see if clocks are */ /* actually there. Because the SBC */ /* after reset does not deactivate */ /* its clocks immediately we will */ /* make pretty sure that the clocks */ /* are there before we leave this */ /* routine */ BitSet = inp (pt->pt_r_star) & STAR_BVS; count = 0; /* we test to see if 6 changes in */ /* the STAR:BVS bit indicating the */ /* reception of at least 3 frames */ /* (6 B channels). If at any time */ /* we fail to find a bit change */ /* and the counter i reaches its */ /* maximum then we assume that */ /* clocks are no longer present */ for (i = 0; i < 500; i++) if ((inp(pt->pt_r_star) & STAR_BVS) != BitSet) { /* Of course we have to reset our */ /* counter every time a bit change */ if (++count > 6) /* is observed to give the next */ return (FALSE); /* bit change the same amount of */ /* time in which to occur !!! */ i = 0; BitSet = inp (pt->pt_r_star) & STAR_BVS; } /* /* /* /* /* /* /* /* Semiconductor Group the Bx versions reqire one edge at FSC. Otherwise the setting of the SPU has no effect (result: no clock) The IOM direction control bit IDC in the ADF1 (SQXR) register is set before and reset after the system is clocking 229 */ */ */ */ */ */ */ */ Low Level Controller /* ICC Bx: IDC is in reg. ADF1 */ /* ISAC-S Bx: IDC is in reg. SQXR */ if (pt->pt_device == PT_ICC_B) outp (pt->pt_r_adfr, 0x10); if (pt->pt_device == PT_ISAC_S_B) outp (pt->pt_r_sqxr, 0x80); spcr = inp(pt->pt_r_spcr); outp (pt->pt_r_spcr, spcr | SPCR_SPU); if (pt->pt_state & PT_IOM2) outp (pt->pt_r_cixr, CIXR_TBC | CI_TIM | 0x03); else outp (pt->pt_r_cixr, CIXR_TBC | CI_TIM); /* wait for power up indication while ((inp(pt->pt_r_cixr) & CIR_MASK) != CI_PU) if (++i > 1000) break; /* time out */ */ outp (pt->pt_r_spcr, spcr); /* now reset the IDC bit */ /* ICC Bx: IDC is in reg. ADF1 */ /* ISAC-S Bx: IDC is in reg. SQXR */ if (pt->pt_device == PT_ICC_B) outp (pt->pt_r_adfr, 0x00); if (pt->pt_device == PT_ISAC_S_B) outp (pt->pt_r_sqxr, 0x00); return (TRUE); } /***************************************************************************/ /* */ /* Function: InitL1_SBC () */ /* Parms : PEI value, mode of operation */ /* purpose : initialize an SBC controlling ICC / L1 part of an ISAC-S */ /* reset L1 to come to default state */ /* */ /***************************************************************************/ EXPORT int InitL1_SBC (pei, mode_type) BYTE pei, mode_type; { register PEITAB *pt; BYTE r_mode; /* return if the addressed device /* is not operational or not used /* for LAYER 1 control if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); if (!(pt->pt_state & PT_L1_CTRL)) Semiconductor Group 230 */ */ */ Low Level Controller return (ACK_NOT_SUPPORTED); outp (pt->pt_r_mask, 0xFF); /* /* /* /* compare the requested initialization mode with detected hardware configuration ('pt_ModulMode') */ */ */ */ if (pt->pt_ModulMode != mode_type) { outp (pt->pt_r_mask, 0x00); return (ACK_WRONG_MODUL_MODE); } /* timing mode 0 is used on the /* SIPB for TE and NTS configu/* ration */ */ */ r_mode = inp (pt->pt_r_mode); if (mode_type == PT_MM_TE) outp (pt->pt_r_mode, (r_mode & ~(MODE_HMD2 | MODE_HMD1)) | MODE_HMD0); else outp (pt->pt_r_mode, r_mode & ~(MODE_HMD2 | MODE_HMD1 | MODE_HMD0)); if (pt->pt_state & PT_IOM2) { outp (pt->pt_r_adf2, 0x80); /* IOM 2 mode ? */ /* program IOM2 mode in ICC/ISAC-S */ /* Changed to be terminal mode /* timing rather than SPCR_SPM */ */ /* no terminal specific functions */ switch (mode_type) { case PT_MM_NT: outp (pt->pt_r_spcr, 0x00); outp (pt->pt_r_stcr, 0x00); outp (pt->pt_r_mode, (r_mode & ~(MODE_HMD2 | MODE_HMD0)) | MODE_HMD1); break; case PT_MM_TE: outp (pt->pt_r_spcr, 0x00); outp (pt->pt_r_stcr, 0x70); /* terminal mode /* TIC bus address '7' /* no watchdog timer */ */ */ break; } } else { outp (pt->pt_r_adf2, 0x00); outp (pt->pt_r_stcr, 0x70); } /* program IOM2 mode in ICC/ISAC-S /* program TIC bus address outp (pt->pt_r_mask, 0x00); Semiconductor Group 231 */ */ Low Level Controller if (!ResL1_SBC (pt)) return (ACK_ACCESS_FAULT); return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: ActL1_SBC () */ /* Parms : PEI value */ /* purpose : establish L1 link (= activation) */ /* */ /***************************************************************************/ EXPORT int ActL1_SBC (pei) BYTE pei; { register PEITAB *pt; /* return if the addressed device */ /* is not operational or not used */ /* for LAYER 1 control */ if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); if (!(pt->pt_state & PT_L1_CTRL)) return (ACK_NOT_SUPPORTED); /* the activation procedure is not /* done if the layer 1 link is /* already established. In that /* case only an activation /* indication message is generated if (((pt->pt_CI_rec = inp(pt->pt_r_cixr)) & CIR_MASK) != CI_AI) { if (pt->pt_ModulMode == PT_MM_TE) EnaClk_SBC (pt); */ */ */ */ */ if (pt->pt_state & PT_IOM2) outp (pt->pt_r_cixr, CIXR_TBC | CI_AR | 0x03); else outp (pt->pt_r_cixr, CIXR_TBC | CI_AR); return (ACK_DONE); } DECODE_L1_STATUS (pei, pt->pt_CI_rec); return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: ArlL1_SBC () */ /* Parms : PEI value */ /* purpose : activate local loop */ /* */ /***************************************************************************/ EXPORT int Semiconductor Group 232 Low Level Controller ArlL1_SBC (pei) BYTE pei; { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); if (pt->pt_ModulMode == PT_MM_TE) EnaClk_SBC (pt); if (pt->pt_state & PT_IOM2) outp (pt->pt_r_cixr, 0x6B); else outp (pt->pt_r_cixr, 0x68); return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: DeaL1_SBC */ /* Parms : PEI */ /* purpose : release L1 link */ /* */ /***************************************************************************/ EXPORT int DeaL1_SBC (pei) BYTE pei; { register PEITAB *pt; if (!(pt = GetPeitab_BASIC (pei))) return (ACK_NOT_SUPPORTED); if (!(pt->pt_state & PT_L1_CTRL)) return (ACK_NOT_SUPPORTED); if (pt->pt_ModulMode != PT_MM_NT && pt->pt_ModulMode != PT_MM_LT_S) return (ACK_WRONG_MODUL_MODE); if (((pt->pt_CI_rec = inp (pt->pt_r_cixr)) & CIR_MASK) != CI_DIU) { if (pt->pt_state & PT_IOM2) outp (pt->pt_r_cixr, CIXR_TBC | CI_DR | 0x03); else outp (pt->pt_r_cixr, CIXR_TBC | CI_DR); return (ACK_DONE); } DECODE_L1_STATUS (pei, pt->pt_CI_rec); return (ACK_DONE); } /***************************************************************************/ /* */ /* Function: IntL1_SBC () */ Semiconductor Group 233 Low Level Controller /* Parms : pointer to PEITAB table element of ICC / ISAC-S */ /* purpose : handle C/I interrupts */ /* */ /***************************************************************************/ EXPORT void IntL1_SBC (pt) register PEITAB *pt; { pt->pt_CI_rec = inp (pt->pt_r_cixr);/* read CIRR (CIR0) register */ if (pt->pt_ModulMode == PT_MM_NT) { /* in NT / LT-S configuration: */ /* send DID if SBC/ISAC-S is in the */ /* DIU state */ /* -> deactivation */ if ((pt->pt_CI_rec & CIR_MASK) == CI_DIU) { if (pt->pt_state & PT_IOM2) outp (pt->pt_r_cixr, CIXR_TBC | CI_DID | 0x03); else outp (pt->pt_r_cixr, CIXR_TBC | CI_DID); } } else { /* TE configuration: /* power down SBC/ISAC-S if it has /* changed from activated to /* pending mode if ((pt->pt_CI_rec & CIR_MASK) == CI_DR) { if (pt->pt_state & PT_IOM2) outp (pt->pt_r_cixr, CIXR_TBC | CI_DIU | 0x03); else outp (pt->pt_r_cixr, CIXR_TBC | CI_DIU); */ */ */ */ } /* /* /* /* /* /* activation confirmation in IOM2 configurations. The SBC (ISAC-S) must confirm an activation from network side. Only then it will be transparent for upstream B channel data */ */ */ */ */ */ if ((pt->pt_state & PT_IOM2) && ((pt->pt_CI_rec & CIR_MASK) == CI_AI)) outp (pt->pt_r_cixr, CIXR_TBC | CI_AR | 0x03); } DECODE_L1_STATUS (pt->pt_pei, pt->pt_CI_rec); } /***************************************************************************/ /* */ /* Function: ResL1_SBC () */ /* Parms : pointer to PEITAB table element of ICC / ISAC-S */ /* purpose : Reset SBC / L1 part of ISAC-S */ /* (also used for device test) */ Semiconductor Group 234 Low Level Controller /* */ /***************************************************************************/ EXPORT int ResL1_SBC (pt) register PEITAB *pt; { int i, state, failed = FALSE; BYTE ForceCommand, NewState, ReleaseCommand, Loop, r_spcr; switch (pt->pt_ModulMode) { case PT_MM_TE: ForceCommand = CI_RS; NewState = CI_EI; ReleaseCommand = CI_DIU; break; case PT_MM_NT: ForceCommand = CI_DR; NewState = CI_DIU; ReleaseCommand = CI_DID; /* /* /* /* send the RES (reset) code and wait for a change to the EI state, then send DIU */ */ */ */ /* /* /* /* /* send the deactivation request code and wait for DIU then send DID to deactivate the SBC */ */ */ */ */ break; default: if (pt->pt_Lay1id == SBC_LAY1) pt->pt_Lay1id = UNK_LAY1; return (FALSE); } if (pt->pt_state & PT_IOM2) { ReleaseCommand |= 0x03; ForceCommand |= 0x03; } state = ENTERNOINT (); /* disable all system interrupts */ /* if testloop mode was programmed /* switch it off to enable L1 /* status recognition */ */ */ r_spcr = inp (pt->pt_r_spcr); if (Loop = (r_spcr & SPCR_TPL)) outp (pt->pt_r_spcr, (r_spcr & ~SPCR_TPL)); outp (pt->pt_r_mask, ~ISTA_CIC); /* allow only C/I interrupts */ if (pt->pt_ModulMode == PT_MM_TE) EnaClk_SBC (pt); /* output the command code outp (pt->pt_r_cixr, (BYTE) (CIXR_TBC | ForceCommand)); Semiconductor Group 235 */ Low Level Controller i = 0; /* wait for the expected state while ((inp(pt->pt_r_cixr) & CIR_MASK) != NewState) if (i++ > 20000) { /* break if timeout failed = TRUE; break; } */ /* output the release command outp (pt->pt_r_cixr, (BYTE)(CIXR_TBC | ReleaseCommand)); */ if (pt->pt_ModulMode == PT_MM_TE) { */ */ */ */ */ */ /* /* /* /* /* /* TE mode ? Wait for DIU or AIU because it can cause problems for the enable clock routine if the clocks disappear mid routine due to an earlier reset */ for (i = 0; i < 20000; i++) { pt->pt_CI_rec = inp (pt->pt_r_cixr) & CIR_MASK; if ((pt->pt_CI_rec == CI_DIU) || (pt->pt_CI_rec == CI_AI)) break; } if ((pt->pt_state & PT_IOM2) && (pt->pt_CI_rec == CI_AI)) outp (pt->pt_r_cixr, CIXR_TBC | CI_AR | 0x03); } if (Loop) outp (pt->pt_r_spcr, r_spcr); /* restore original value of SPCR */ outp (pt->pt_r_mask, 0x00); LEAVENOINT (state); /* enable interrupts again */ if (failed) { if (pt->pt_Lay1id == SBC_LAY1) pt->pt_Lay1id = UNK_LAY1; return (FALSE); } else return (TRUE); } Semiconductor Group 236 Package Outlines 7 Package Outlines 2.54 1.5 max 0.45 +0.1 0.25 40x 40 ~~ 1.3 3.7 0.3 0.5 min 5.1 max P-DIP-40-2 (Plastic Dual-In-Line Package) 15.24 0.2 0.25 +0.1 14 -0.3 15.24 +1.2 21 1 20 50.9 -0.5 0.25 max GPD05055 Index Marking Dimensions in mm Semiconductor Group 237 Package Outlines GPL05102 Plastic Package, P-LCC-44-1 (SMD) (Plastic-Leaded Chip Carrier) Dimensions in mm Semiconductor Group 238 Package Outlines GPM05250 Plastic Package, P-MQFP-64-1 (SMD) (Plastic Metric Quad Flat Package) Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book "Package Information" Dimensions in mm SMD = Surface Mounted Device Semiconductor Group 239 PackageAppendix Outlines Transformers and Crystals Vendor List Crystals: Frischer Electronic Schleifmuhlstrae 2 D-91054 Erlangen, Germany KVG Waibstadter Strae 2-4 D-74924 Neckarbischofsheim 2, Germany Tel.: (...7263) 648-0 NDK 2-21-1 Chome Nishihara Shibuya-Ku Tokyo 151, Japan Tel.: (03)-460-2111 or Cupertino, CA, USA Tel.: (408) 255-0831 S+M Components Balanstrae 73 P.O. Box 801709 D-81617 Munich, Germany Tel.: (...89) 4144-8041 Fax.: (...89) 4144-8483 Siemens Oostcamp Belgium Schott Corporation Suite 108 1838 Elm Hill Pike, Nashville, TN 37210, USA Tel.: (615) 889-8800 TDK Christinenstrae 25 D-40880 Ratingen 1, Germany Tel.: (...2192) 487-0 Universal Microelectronics Saronix 4010 Transport at San Antonio Palo Alto, CA 94303, USA Tel.: (415) 856-6900 or via Arthur Behrens KG Schrammelweg 3 D-82544 Egling-Neufahrn, Germany Vacuumschmelze (VAC) Gruner Weg 37 Postfach 2253 D-63412 Hanau 1, Germany Tel.: (...6181) 380 or 186 Wood Avenue South Iselin, NJ OB830, USA Tel.: (908) 603 5905 Tele Quarz Landstrae 13 D-74924 Neckarbischofsheim 2, Germany Valor Steinstrae 68 D-81667 Munchen, Germany Tel.: (...89) 480 2823 Fax.: (...89) 484 743 Transformers: Advanced Power Components (APC) 47 Riverside Medway City Estate Strood County of Kent, GB Tel.: (044) 634-290 588 Vogt electronic AG Postfach 1001 D-94128 Obernzell, Germany Tel.: (...8591) 17-0 Fax.: (...8591) 17-240 Pulse Engineering P.O. Box 12235 San Diego, CA 92112, USA Tel.: (619) 268-2454 or 4, avenue du Quebec F-91940 Les Ulis, France or Dunmore Road Tuam County Galway, Ireland Tel.: (093) 24107 Semiconductor Group 240