LM317T NOPB - NATIONAL SEMICONDUCTOR

( )

OUT ADJ

V = 1.25 V I R

æ ö

+ +

ç ÷

è ø

LM317-N

Product

Folder

Order

Now

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

LM117, LM317-N Wide Temperature Three-Pin Adjustable Regulator

1 Features

1• For a newer drop-in alternative, see the LM317

• Typ. 0.1% load regulation

• Typ. 0.01%/V line regulation

• 1.5-A output current

• Adjustable output down to 1.25 V

• Current limit constant with temperature

• 80-dB ripple rejection

• Short-circuit protected output

•−55°C to 150°C operating temperature range

(LM117)

2 Applications

•Multifunction printers

•AC drive power stage modules

•Electricity meters

•Servo drive control modules

•Merchant network and server PSU

Typical Application

*Needed if device is more than 6 inches from filter

capacitors.

†Optional—improves transient response

††

3 Description

The LM117 and LM317-N series of adjustable 3-pin

positive voltage regulators are capable of supplying in

excess of 1.5 A over a 1.25-V to 37-V output range

and a wide temperature range. They are

exceptionally easy to use and require only two

external resistors to set the output voltage. Further,

both line and load regulation are better than standard

fixed regulators.

The LM117 and LM317-N offer full overload

protection such as current limit, thermal overload

protection and safe area protection. All overload

protection circuitry remains fully functional even if the

adjustment terminal is disconnected.

Typically, no capacitors are needed unless the device

is situated more than 6 inches from the input filter

capacitors, in which case an input bypass is needed.

An optional output capacitor can be added to improve

transient response. The adjustment terminal can be

bypassed to achieve very high ripple rejection ratios

that are difficult to achieve with standard 3-terminal

regulators.

Because the regulator is floating and detects only the

input-to-output differential voltage, supplies of several

hundred volts can be regulated as long as the

maximum input-to-output differential is not exceeded.

That is, avoid short-circuiting the output.

By connecting a fixed resistor between the

adjustment pin and output, the LM117 and LM317-N

can be also used as a precision current regulator.

Supplies with electronic shutdown can be achieved

by clamping the adjustment terminal to ground, which

programs the output to 1.25 V where most loads draw

little current.

For applications requiring greater output current, see

the LM150 series (3 A) and LM138 series (5 A) data

sheets. For the negative complement, see the LM137

series data sheet.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

LM117 TO-3 (2) 38.94 mm x 25.40 mm

TO (3) 8.255 mm × 8.255 mm

LM317-N

TO-3 (2) 38.94 mm x 25.40 mm

TO-220 (3) 14.986 mm × 10.16 mm

TO-263 (3) 10.18 mm × 8.41 mm

SOT-223 (4) 6.50 mm × 3.50 mm

TO (3) 8.255 mm × 8.255 mm

TO-252 (3) 6.58 mm × 6.10 mm

(1) For all available packages, see the orderable addendum at

the end of the data sheet.

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Device Comparison Table..................................... 3

6 Pin Configuration and Functions......................... 4

7 Specifications......................................................... 6

7.1 Absolute Maximum Ratings ...................................... 6

7.2 ESD Ratings.............................................................. 6

7.3 Recommended Operating Conditions....................... 6

7.4 Thermal Information, LM117..................................... 6

7.5 Thermal Information, LM317-N................................. 7

7.6 LM117 Electrical Characteristics............................... 7

7.7 LM317-N Electrical Characteristics........................... 8

7.8 Typical Characteristics.............................................. 9

8 Detailed Description............................................ 12

8.1 Overview................................................................. 12

8.2 Functional Block Diagram....................................... 13

8.3 Feature Description................................................. 14

8.4 Device Functional Modes........................................ 14

9 Application and Implementation ........................ 16

9.1 Application Information............................................ 16

9.2 Typical Applications ................................................ 16

10 Power Supply Recommendations ..................... 28

11 Layout................................................................... 28

11.1 Layout Guidelines ................................................. 28

11.2 Layout Examples................................................... 34

12 Device and Documentation Support................. 36

12.1 Documentation Support ........................................ 36

12.2 Related Links ........................................................ 36

12.3 Receiving Notification of Documentation Updates 36

12.4 Support Resources ............................................... 36

12.5 Trademarks........................................................... 36

12.6 Electrostatic Discharge Caution............................ 36

12.7 Glossary................................................................ 36

13 Mechanical, Packaging, and Orderable

Information........................................................... 37

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision P (October 2015) to Revision Q Page

• Added alternative device Features bullet ............................................................................................................................... 1

• Changed Applications section ............................................................................................................................................... 1

• Changed Device Comparison Table ...................................................................................................................................... 3

• Changed Related Documentation section............................................................................................................................ 36

Changes from Revision O (January 2014) to Revision P Page

• Added, updated, or renamed the following sections: Description;Pin Configuration and Functions;Specifications;

ESD Ratings table; Application and Implementation;Power Supply Recommendations;Layout;Mechanical,

Packaging, and Ordering Information .................................................................................................................................... 1

• Removed information regarding LM317A, formerly part of this data sheet. LM317A can now be found in the TI

catalog under literature number SNVSAC2 ........................................................................................................................... 1

Changes from Revision N (August 2013) to Revision O Page

• Deleted MDT Package (over Full Operating Temperature Range) ....................................................................................... 8

• Changed Current Limit MIN from 0.112 to 0.15 and TYP from 0.3 to 0.4 for (VIN – VOUT) = 40 V in the LM317A

and LM317-N Electrical Characteristics Section .................................................................................................................... 8

• Deleted MDT Package ........................................................................................................................................................... 8

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

5 Device Comparison Table

IOUT PARAMETER LM317 LM317-N LM317A LM317HV UNIT

1.5 A

Input voltage range 4.25 - 40 4.25 - 40 4.25 - 40 4.25 - 60 V

Load regulation accuracy 1.5 1.5 1 1.5 %

PSRR (120 Hz) 64 80 80 65 dB

Recommended operating temperature 0 to 125 0 to 125 –40 to 125 0 to 125 °C

TO-220 (NDE) TJA 23.5 23.2 23.3 23 °C/W

TO-200 (KCT) TJA 37.9 N/A N/A N/A °C/W

TO-252 TJA N/A 54 54 N/A °C/W

TO-263 TJA 38 41 N/A N/A °C/W

SOT-223 TJA 66.8 59.6 59.6 N/A °C/W

TO-92 TJA N/A 186 186 N/A °C/W

0.5 A

LM317M

Input voltage range 3.75 - 40 V

Load regulation accuracy 1.5 %

PSRR (120 Hz) 80 dB

Recommended operating temperature -40 - 125 °C

SOT-223 TJA 60.2 °C/W

TO-252 TJA 56.9 °C/W

0.1 A

LM317L LM317L-N

Input voltage range 3.75 - 40 4.25 - 40 V

Load regulation accuracy 1 1.5 %

PSRR (120 Hz) 62 80 dB

Recommended operating temperature –40 to 125 –40 to 125 °C

SOT-23 TJA 167.8 N/A °C/W

SO-8 TJA N/A 165 °C/W

DSBGA TJA N/A 290 °C/W

TO-92 TJA N/A 180 °C/W

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

6 Pin Configuration and Functions

NDS Metal Can Package

2-Pin TO-3

Bottom View

Case is Output

NDT Metal Can Package

3-Pin TO

Bottom View

Case is Output

Pin Functions, Metal Can Packages

PIN I/O DESCRIPTION

NAME TO-3 TO

ADJ 1 2 — Adjust pin

VOUT CASE 3, CASE O Output voltage pin for the regulator

VIN 2 1 I Input voltage pin for the regulator

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

KTT Surface-Mount Package

3-Pin DDPAK/TO-263

Top View

NDE Plastic Package

3-Pin TO-220

Front View

DCY Surface-Mount Package

4-Pin SOT-223

Top View

NDP Surface-Mount Package

3-Pin TO-252

Front View

Pin Functions

PIN I/O DESCRIPTION

NAME TO-263 TO-220 SOT-223 TO-252

ADJ 1 1 1 1 — Adjust pin

VOUT 2, TAB 2, TAB 2, 4 2, TAB O Output voltage pin for the regulator

VIN 3 3 3 3 I Input voltage pin for the regulator

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and

specifications.

7 Specifications

7.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)(2)

MIN MAX UNIT

Power dissipation Internally Limited

Input-output voltage differential −0.3 40 V

Storage temperature, Tstg −65 150 °C

(1) Manufacturing with less than 500-V HBM is possible with the necessary precautions. Pins listed as ±3000 V may actually have higher

performance.

7.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic

discharge Human-body model (HBM)(1) ±3000 V

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

Operating temperature (LM117) −55 150 °C

Operating temperature (LM317-N) 0 125 °C

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC package thermal metrics application

report.

(2) No heatsink.

7.4 Thermal Information, LM117

THERMAL METRIC(1)

LM117

UNIT

NDS

(TO-3) NDT

(TO)

2 PINS 3 PINS

RθJA Junction-to-ambient thermal resistance(2) 39 186 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 2 21 °C/W

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC package thermal metrics application

report.

(2) When surface mount packages are used (SOT-223, TO-252), the junction to ambient thermal resistance can be reduced by increasing

the PCB copper area that is thermally connected to the package. See Heatsink Requirements for heatsink techniques.

(3) No heatsink.

7.5 Thermal Information, LM317-N

THERMAL METRIC(1)(2)

LM317-N

UNIT

KTT

(TO-263) NDE

(TO-220) DCY

(SOT-223) NDT

(TO) NDP

(TO-252)

3 PINS 3 PINS 4 PINS 3 PINS 3 PINS

RθJA Junction-to-ambient thermal resistance 41.0 23.3 59.6 186(3) 54 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 43.6 16.2 39.3 21 51.3 °C/W

RθJB Junction-to-board thermal resistance 23.6 4.9 8.4 — 28.6 °C/W

ψJT Junction-to-top characterization parameter 10.4 2.7 1.8 — 3.9 °C/W

ψJB Junction-to-board characterization parameter 22.6 4.9 8.3 — 28.1 °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance 0.9 1.1 — — 0.9 °C/W

(1) IMAX = 1.5 A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0 A for the DCY (SOT-223) package.

IMAX = 0.5 A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA),

device maximum junction temperature (TJ), and package thermal resistance (RθJA). The maximum allowable power dissipation at any

temperature is : PD(MAX) = ((TJ(MAX) – TA) / RθJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL).

(2) Specifications and availability for military and space grades of LM117/883 can be found in the LM117QML data sheet. Specifications

and availability for military and space grades of LM117 can be found in the LM117JAN data sheet.

(3) Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to

heating effects are covered under the specifications for thermal regulation.

7.6 LM117 Electrical Characteristics

Some specifications apply over full Operating Temperature Range as noted. Unless otherwise specified, TJ= 25°C, VIN −

VOUT = 5 V, and IOUT = 10 mA.(1)(2)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Reference voltage 3 V ≤(VIN −VOUT)≤40 V,

10 mA ≤IOUT ≤IMAX(1) (over full operating temperature range) 1.2 1.25 1.3 V

Line regulation 3 V ≤(VIN −VOUT)≤40 V(3) TJ= 25°C 0.01 0.02 %/V

over full operating

temperature range 0.02 0.05

Load regulation 10 mA ≤IOUT ≤IMAX(1)(3) TJ= 25°C 0.1% 0.3%

over full operating

temperature range 0.3% 1%

Thermal regulation 20-ms pulse 0.03 0.07 %/W

Adjustment pin current over full operating temperature range 50 100 μA

Adjustment pin current change 10 mA ≤IOUT ≤IMAX(1)

3 V ≤(VIN −VOUT)≤40 V (over full operating temperature range) 0.2 5 μA

Temperature stability TMIN ≤TJ≤TMAX (over full operating temperature range) 1%

Minimum load current (VIN −VOUT) = 40 V (over full operating temperature range) 3.5 5 mA

Current limit (VIN −VOUT)≤15 V

TO-3 Package (over full

operating temperature range) 1.5 2.2 3.4 A

TO-39 Package (over full

operating temperature range) 0.5 0.8 1.8

(VIN −VOUT) = 40 V TO-3 package 0.3 0.4 A

TO-39 package 0.15 0.2

RMS output noise, % of VOUT 10 Hz ≤f≤10 kHz 0.003%

Ripple rejection ratio

VOUT = 10 V, f = 120 Hz, CADJ = 0 μF (over full operating

temperature range) 65 dB

VOUT = 10 V, f = 120 Hz, CADJ = 10 μF (over full operating

temperature range) 66 80 dB

Long-term stability TJ= 125°C, 1000 hrs 0.3% 1%

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

(1) IMAX = 1.5 A for the NDS (TO-3), NDE (TO-220), and KTT (TO-263) packages. IMAX = 1.0 A for the DCY (SOT-223) package.

IMAX = 0.5 A for the NDT (TO) and NDP (TO-252) packages. Device power dissipation (PD) is limited by ambient temperature (TA),

device maximum junction temperature (TJ), and package thermal resistance (RθJA). The maximum allowable power dissipation at any

temperature is : PD(MAX) = ((TJ(MAX) – TA) / RθJA). All Min. and Max. limits are ensured to TI's Average Outgoing Quality Level (AOQL).

(2) Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to

heating effects are covered under the specifications for thermal regulation.

7.7 LM317-N Electrical Characteristics(1)

Some specifications apply over full Operating Temperature Range as noted. Unless otherwise specified, TJ= 25°C, VIN −

VOUT = 5 V, and IOUT = 10 mA.

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Reference voltage

TJ= 25°C 1.25 V

3 V ≤(VIN −VOUT)≤40 V,

10 mA ≤IOUT ≤IMAX(1) (over Full Operating Temperature

Range) 1.2 1.25 1.3 V

Line regulation 3V ≤(VIN −VOUT)≤40 V(2) TJ= 25°C 0.01 0.04 %/V

(over full operating

temperature range) 0.02 0.07

Load regulation 10 mA ≤IOUT ≤IMAX(1)(2) TJ= 25°C 0.1% 0.5%

(over full operating

temperature range) 0.3% 1.5%

Thermal regulation 20-ms pulse 0.04 0.07 %/W

Adjustment pin current (over full operating temperature range) 50 100 μA

Adjustment pin current change 10 mA ≤IOUT ≤IMAX(1)

3V ≤(VIN −VOUT)≤40V (over full operating

temperature range) 0.2 5 μA

Temperature stability TMIN ≤TJ≤TMAX (over full operating

temperature range) 1%

Minimum load current (VIN −VOUT) = 40 V (over full operating

temperature range) 3.5 10 mA

Current limit

(VIN −VOUT)≤15 V

TO-3, TO-263 Packages

(over full operating

temperature range) 1.5 2.2 3.4

SOT-223, TO-220

Packages (over full

operating temperature

range) 1.5 2.2 3.4

TO, TO-252 Package (over

full operating temperature

range) 0.5 0.8 1.8

(VIN −VOUT) = 40 V TO-3, TO-263 packages 0.15 0.4 ASOT-223, TO-220 packages 0.15 0.4

TO, TO-252 package 0.075 0.2

RMS output noise, % of VOUT 10 Hz ≤f≤10 kHz 0.003%

Ripple rejection ratio

VOUT = 10 V, f = 120 Hz, CADJ = 0 μF (over full operating

temperature range) 65 dB

VOUT = 10V, f = 120 Hz, CADJ = 10 μF (over full operating

temperature range) 66 80 dB

Long-term stability TJ= 125°C, 1000 hrs 0.3% 1%

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

7.8 Typical Characteristics

output Capacitor = 0 μF (unless otherwise noted)

Figure 1. Load Regulation Figure 2. Current Limit

Figure 3. Adjustment Current Figure 4. Dropout Voltage

Figure 5. VOUT vs VIN, VOUT = VREF Figure 6. VOUT vs VIN, VOUT = 5 V

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Typical Characteristics (continued)

output Capacitor = 0 μF (unless otherwise noted)

Figure 7. Temperature Stability Figure 8. Minimum Operating Current

Figure 9. Ripple Rejection Figure 10. Ripple Rejection

Figure 11. Ripple Rejection Figure 12. Output Impedance

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Characteristics (continued)

output Capacitor = 0 μF (unless otherwise noted)

Figure 13. Line Transient Response Figure 14. Load Transient Response

LM317-N

( )

OUT ADJ

V = 1.25 V I R

æ ö

+ +

ç ÷

è ø

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

8 Detailed Description

8.1 Overview

In operation, the LM317-N develops a nominal 1.25-V reference voltage, VREF, between the output and

adjustment terminal. The reference voltage is impressed across program resistor R1 and, because the voltage is

constant, a constant current I1then flows through the output set resistor R2, giving an output voltage calculated

by Equation 1:

(1)

Figure 15. Setting the VOUT Voltage

Because the 100-μA current from the adjustment terminal represents an error term, the LM317-N was designed

to minimize IADJ and make it very constant with line and load changes. To do this, all quiescent operating current

is returned to the output establishing a minimum load current requirement. If there is insufficient load on the

output, the output will rise.

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

8.2 Functional Block Diagram

LM317-N

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

8.3 Feature Description

8.3.1 Load Regulation

The LM317-N is capable of providing extremely good load regulation but a few precautions are needed to obtain

maximum performance. The current set resistor, R1, must be connected near the output terminal of the regulator

rather than near the load. If R1 is placed too far from the output terminal, then the increased trace resistance, RS,

will cause an error voltage drop in the adjustment loop and degrade load regulation performance. Therefore, R1

must be placed as close as possible to the output terminal to minimize RSand maximize load regulation

performance.

Figure 16 shows the effect of the trace resistance, RS, when R1 is placed far from the output terminal of the

regulator. It is clear that RSwill cause an error voltage drop especially during higher current loads, so it is

important to minimize the RStrace resistance by keeping R1 close to the regulator output terminal.

Figure 16. Regulator With Line Resistance in Output Lead

With the TO-3 package, it is easy to minimize the resistance from the case to the set resistor, by using two

separate leads to the case. However, with the TO package, care must be taken to minimize the wire length of the

output lead. The ground of R2 can be returned near the ground of the load to provide remote ground sensing

and improve load regulation.

8.4 Device Functional Modes

8.4.1 External Capacitors

An input bypass capacitor is recommended. A 0.1-μF disc or 1-μF solid tantalum on the input is suitable input

bypassing for almost all applications. The device is more sensitive to the absence of input bypassing when

adjustment or output capacitors are used, but the above values will eliminate the possibility of problems.

The adjustment terminal can be bypassed to ground on the LM317-N to improve ripple rejection. This bypass

capacitor prevents ripple from being amplified as the output voltage is increased. With a 10-μF bypass capacitor,

80-dB ripple rejection is obtainable at any output level. Increases over 10 μF do not appreciably improve the

ripple rejection at frequencies above 120 Hz. If the bypass capacitor is used, it is sometimes necessary to

include protection diodes to prevent the capacitor from discharging through internal low current paths and

damaging the device.

In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance

even at high frequencies. Depending upon capacitor construction, it takes about 25 μF in aluminum electrolytic to

equal 1-μF solid tantalum at high frequencies. Ceramic capacitors are also good at high frequencies. However,

some types have a large decrease in capacitance at frequencies around 0.5 MHz. For this reason, 0.01-μF disc

may seem to work better than a 0.1-μF disc as a bypass.

Although the LM317-N is stable with no output capacitors, like any feedback circuit, certain values of external

capacitance can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1-μF solid

tantalum (or 25-μF aluminum electrolytic) on the output swamps this effect and insures stability. Any increase of

the load capacitance larger than 10 μF will merely improve the loop stability and output impedance.

( )

OUT ADJ

V = 1.25 V I R

æ ö

+ +

ç ÷

è ø

LM317-N

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Device Functional Modes (continued)

8.4.2 Protection Diodes

When external capacitors are used with any IC regulator, it is sometimes necessary to add protection diodes to

prevent the capacitors from discharging through low current points into the regulator. Most 10-μF capacitors have

low enough internal series resistance to deliver 20-A spikes when shorted. Although the surge is short, there is

enough energy to damage parts of the IC.

When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge

into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage

of the regulator, and the rate of decrease of VIN. In the LM317-N, this discharge path is through a large junction

that is able to sustain 15-A surge with no problem. This is not true of other types of positive regulators. For

output capacitors of 25 μF or less, there is no need to use diodes.

The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs

when either the input, or the output, is shorted. Internal to the LM317-N is a 50-Ωresistor which limits the peak

discharge current. No protection is needed for output voltages of 25 V or less and 10-μF capacitance. Figure 17

shows an LM317-N with protection diodes included for use with outputs greater than 25 V and high values of

output capacitance.

D1 protects against C1

D2 protects against C2

Figure 17. Regulator With Protection Diodes

LM317-N

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers must

validate and test their design implementation to confirm system functionality.

9.1 Application Information

The LM117 and LM317-N are versatile, high performance, linear regulators with high accuracy and a wide

temperature range. An output capacitor can be added to further improve transient response, and the ADJ pin can

be bypassed to achieve very high ripple-rejection ratios. Its functionality can be utilized in many different

applications that require high performance regulation, such as battery chargers, constant current regulators, and

microprocessor supplies.

9.2 Typical Applications

9.2.1 1.25-V to 25-V Adjustable Regulator

The LM117 can be used as a simple, low-dropout regulator to enable a variety of output voltages needed for

demanding applications. By using an adjustable R2 resistor, a variety of output voltages can be made possible

as shown in Figure 18.

NOTE: Full output current not available at high input-output voltages

*Needed if device is more than 6 inches from filter capacitors.

†Optional—improves transient response. Output capacitors in the range of 1 μF to 1000 μF of aluminum or tantalum

electrolytic are commonly used to provide improved output impedance and rejection of transients.

Figure 18. 1.25-V to 25-V Adjustable Regulator

9.2.1.1 Design Requirements

The device component count is very minimal, employing two resistors as part of a voltage divider circuit and an

output capacitor for load regulation. An input capacitor is needed if the device is more than 6 inches from filter

capacitors. An optional bypass capacitor across R2 can also be used to improve PSRR.

9.2.1.2 Detailed Design Procedure

The output voltage is set based on the selection of the two resistors, R1 and R2, as shown in Figure 18. For

details on capacitor selection, refer to External Capacitors.

LM317-N

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.1.3 Application Curve

As shown in Figure 19, VOUT will rise with VIN minus some dropout voltage. This dropout voltage during startup

will vary with ROUT.

Figure 19. VOUT vs VIN, VOUT = 5V

9.2.2 5-V Logic Regulator With Electronic Shutdown

Figure 20 shows a variation of the 5-V output regulator application uses the L117 along with an NPN transistor to

provide shutdown control. The NPN will either block or sink the current from the ADJ pin by responding to the

TTL pin logic. When TTL is pulled high, the NPN is on and pulls the ADJ pin to GND, and the LM117 outputs

about 1.25 V. When TTL is pulled low, the NPN is off and the regulator outputs according to the programmed

adjustable voltage.

NOTE: Min. output ≊1.2 V

Figure 20. 5-V Logic Regulator With Electronic Shutdown

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.3 Slow Turnon 15-V Regulator

An application of LM117 includes a PNP transistor with a capacitor to implement slow turnon functionality (see

Figure 21). As VIN rises, the PNP sinks current from the ADJ rail. The output voltage at start up is the addition of

the 1.25-V reference plus the drop across the base to emitter. While this is happening, the capacitor begins to

charge and eventually opens the PNP. At this point, the device functions normally, regulating the output at 15 V.

A diode is placed between C1 and VOUT to provide a path for the capacitor to discharge. Such controlled turnon

is useful for limiting the in-rush current.

Figure 21. Slow Turnon 15-V Regulator

267 

1.5 k

2 k

0.1 µF

LM329

VIN

15 V

VOUT

10 V

VIN VOUT

LM117

ADJ

LM317-N

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.4 Adjustable Regulator With Improved Ripple Rejection

To improve ripple rejection, a capacitor is used to bypass the ADJ pin to GND (see Figure 22). This is used to

smooth output ripple by cleaning the feedback path and stopping unnecessary noise from being fed back into the

device, propagating the noise.

NOTE: †Solid tantalum

*Discharges C1 if output is shorted to ground

Figure 22. Adjustable Regulator With Improved Ripple Rejection

9.2.5 High Stability 10-V Regulator

Using a high stability shunt voltage reference in the feedback path, such as the LM329, provides damping

necessary for a stable, low noise output (see Figure 23).

Figure 23. High Stability 10-V Regulator

three LM195 devices in parallel

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.6 High-Current Adjustable Regulator

Using the LM195 power transistor in parallel with the LM117 can increase the maximum possible output load

current (see Figure 24). Sense resistor R1 provides the 0.6 V across base to emitter to turn on the PNP. This on

switch allows current to flow, and the voltage drop across R3 drives three LM195 power transistors designed to

carry an excess of 1 A each.

NOTE

The selection of R1 determines a minimum load current for the PNP to turn on. The higher

the resistor value, the lower the load current must be before the transistors turn on.

NOTE: ‡Optional—improves ripple rejection

†Solid tantalum

*Minimum load current = 30 mA

Figure 24. High-Current Adjustable Regulator

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.7 Emitter-Follower Current Amplifier

The LM117 is used as a constant current source in the emitter follower circuit (see Figure 25). The LM195 power

transistor is being used as a current gain amplifier, boosting the INPUT current. The LM117 provides a stable

current bias than just using a resistor.

Figure 25. Emitter-Follower Current Amplifier

9.2.8 1-A Current Regulator

A simple, fixed current regulator can be made by placing a resistor between the VOUT and ADJ pins of the LM117

(see Figure 26). By regulating a constant 1.25 V between these two terminals, a constant current is delivered to

the load.

Figure 26. 1-A Current Regulator

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.9 Common-Emitter Amplifier

Sometimes it is necessary to use a power transistor for high current gain. In this case, the LM117 provides

constant current at the collector of the LM195 in this common emitter application (see Figure 27). The 1.25-V

reference between VOUT and ADJ is maintained across the 2.4-Ωresistor, providing about 500-mA constant bias

current into the collector of the LM195.

Figure 27. Common-Emitter Amplifier

LM317-N

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.10 Low-Cost 3-A Switching Regulator

The LM317-N can be used in a switching buck regulator application in cost sensitive applications that require

high efficiency. The switch node above D1 oscillates between ground and VIN, as the voltage across sense

resistor R1 drives the power transistor on and off. Figure 28 exhibits self-oscillating behavior by negative

feedback through R6 and C3 to the ADJ pin of the LM317-N.

NOTE: †Solid tantalum

*Core—Arnold A-254168-2 60 turns

Figure 28. Low-Cost 3-A Switching Regulator

LM117

Short circuit current is approximately , or 210 mA

600

LM317-N

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.11 Current-Limited Voltage Regulator

A maximum limit on output current can be set using the circuit shown in Figure 29. The load current travels

through R3 and R4. As the load current increases, the voltage drop across R3 increases until the NPN transistor

is driven, during which the ADJ pin is pulled down to ground and the output voltage is pulled down to the

reference voltage of 1.25 V.

(Compared to LM117's higher current limit)

—At 50 mA output only ¾ volt of drop occurs in R3and R4

Figure 29. Current-Limited Voltage Regulator

9.2.12 Adjusting Multiple On-Card Regulators With Single Control

Figure 30 shows how multiple LM117 regulators can be controlled by setting one resistor. Because each device

maintains the reference voltage of about 1.25 V between its VOUT and ADJ pins, we can connect each ADJ rail to

a single resistor, setting the same output voltage across all devices. This allows for independent outputs, each

responding to its corresponding input only. Designers must also consider that by the nature of the circuit,

changes to R1 and R2 will affect all regulators.

NOTE: *All outputs within ±100 mV

†Minimum load—10 mA

Figure 30. Adjusting Multiple On-Card Regulators With Single Control

LM317-N

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.13 AC Voltage Regulator

In Figure 31, the top regulator is +6 V above the bottom regulator. It is clear that when the input rises above +6 V

plus the dropout voltage, only the top LM317-N regulates +6 V at the output. When the input falls below –6 V

minus the dropout voltage, only the bottom LM317-N regulates –6 V at the output. For regions where the output

is not clipped, there is no regulation taking place, so the output follows the input.

Figure 31. AC Voltage Regulator

9.2.14 12-V Battery Charger

The LM317-N can be used in a battery charger application shown in Figure 32, where the device maintains either

constant voltage or constant current mode depending on the current charge of the battery. To do this, the part

senses the voltage drop across the battery and delivers the maximum charging current necessary to charge the

battery. When the battery charge is low, there exists a voltage drop across the sense resistor RS, providing

constant current to the battery at that instant. As the battery approaches full charge, the potential drop across RS

approaches zero, reducing the current and maintaining the fixed voltage of the battery.

Use of RSallows low charging rates with fully charged battery.

Figure 32. 12-V Battery Charger

LM317-N

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.15 Adjustable 4-A Regulator

Using three LM317-N devices in parallel increases load current capability (Figure 33). Output voltage is set by

the variable resistor tied to the non-inverting terminal of the operational amplifier, and reference current to the

transistor is developed across the 100 Ωresistor. When output voltage rises, the operational amplifier corrects by

drawing current from the base, closing the transistor. This effectively pulls ADJ down and lowers the output

voltage through negative feedback.

Figure 33. Adjustable 4-A Regulator

LM317-N

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Typical Applications (continued)

9.2.16 Current-Limited 6-V Charger

The current in a battery charger application is limited by switching between constant current and constant voltage

states (see Figure 34). When the battery pulls low current, the drop across the 1 Ωresistor is not substantial and

the NPN remains off. A constant voltage is seen across the battery, as regulated by the resistor divider. When

current through the battery rises past peak current, the 1 Ωprovides enough voltage to turn the transistor on,

pulling ADJ close to ground. This results in limiting the maximum current to the battery.

*Sets peak current (0.6A for 1Ω)

**The 1000-μF is recommended to filter out input transients

Figure 34. Current-Limited 6-V Charger

9.2.17 Digitally Selected Outputs

Figure 35 demonstrates a digitally selectable output voltage. In its default state, all transistors are off and the

output voltage is set based on R1 and R2. By driving certain transistors, the associated resistor is connected in

parallel to R2, modifying the output voltage of the regulator.

*Sets maximum VOUT

Figure 35. Digitally Selected Outputs

(2)

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

10 Power Supply Recommendations

The input supply to the LM117 and LM317-N must be kept at a voltage level such that its maximum input to

output differential voltage is not exceeded. The minimum dropout voltage must also be met with extra headroom

when possible to keep the LM117 and LM317-N in regulation. An input capacitor is recommended, especially

when the input pin is located more than 6 inches away from the power supply source. For more information

regarding capacitor selection, refer to External Capacitors.

11 Layout

11.1 Layout Guidelines

Some layout guidelines must be followed to ensure proper regulation of the output voltage with minimum noise.

Traces carrying the load current must be wide to reduce the amount of parasitic trace inductance and the

feedback loop from VOUT to ADJ must be kept as short as possible. To improve PSRR, a bypass capacitor can

be placed at the ADJ pin and must be located as close as possible to the IC. In cases when VIN shorts to ground,

an external diode must be placed from VOUT to VIN to divert the surge current from the output capacitor and

protect the IC. Similarly, in cases when a large bypass capacitor is placed at the ADJ pin and VOUT shorts to

ground, an external diode must be placed from ADJ to VOUT to provide a path for the bypass capacitor to

discharge. These diodes must be placed close to the corresponding IC pins to increase their effectiveness.

11.1.1 Thermal Considerations

11.1.1.1 Heatsink Requirements

The LM317-N regulators have internal thermal shutdown to protect the device from over-heating. Under all

operating conditions, the junction temperature of the LM317-N must not exceed the rated maximum junction

temperature (TJ) of 150°C for the LM117, or 125°C for the LM317-N. A heatsink may be required depending on

the maximum device power dissipation and the maximum ambient temperature of the application. To determine if

a heatsink is needed, the power dissipated by the regulator, PD, must be calculate with Equation 3:

PD= ((VIN −VOUT) × IL) + (VIN × IG) (3)

Figure 36 shows the voltage and currents which are present in the circuit.

The next parameter which must be calculated is the maximum allowable temperature rise, TR(MAX) in Equation 4:

TR(MAX) = TJ(MAX) −TA(MAX) (4)

where TJ(MAX) is the maximum allowable junction temperature (150°C for the LM117, or 125°C for the LM317-N),

and TA(MAX) is the maximum ambient temperature that will be encountered in the application.

Using the calculated values for TR(MAX) and PD, the maximum allowable value for the junction-to-ambient thermal

resistance (RθJA) can be calculated with Equation 5:

RθJA = (TR(MAX) / PD) (5)

Figure 36. Power Dissipation Diagram

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Layout Guidelines (continued)

If the calculated maximum allowable thermal resistance is higher than the actual package rating, then no

additional work is needed. If the calculated maximum allowable thermal resistance is lower than the actual

package rating either the power dissipation (PD) needs to be reduced, the maximum ambient temperature TA(MAX)

needs to be reduced, the thermal resistance (RθJA) must be lowered by adding a heatsink, or some combination

of these.

If a heatsink is needed, the value can be calculated from Equation 6:

θHA ≤(RθJA – (θCH + RθJC))

where

•θCH is the thermal resistance of the contact area between the device case and the heatsink surface

• RθJC is thermal resistance from the junction of the die to surface of the package case (6)

When a value for θHA is found using the equation shown, a heatsink must be selected that has a value that is

less than, or equal to, this number.

The θHA rating is specified numerically by the heatsink manufacturer in the catalog, or shown in a curve that plots

temperature rise vs power dissipation for the heatsink.

11.1.1.2 Heatsinking Surface Mount Packages

The TO-263 (KTT), SOT-223 (DCY) and TO-252 (NDP) packages use a copper plane on the PCB and the PCB

itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the package to

the plane.

11.1.1.2.1 Heatsinking the SOT-223 (DCY) Package

Figure 37 and Figure 38 show the information for the SOT-223 package. Figure 38 assumes a RθJA of 74°C/W

for 1-oz. copper and 59.6°C/W for 2-oz. copper and a maximum junction temperature of 125°C. See the AN-1028

Maximum Power Enhancement Techniques for Power Packages application note for thermal enhancement

techniques to be used with SOT-223 and TO-252 packages.

Figure 37. RθJA vs Copper (2-oz.) Area for the SOT-223

Package Figure 38. Maximum Power Dissipation vs TAMB for the

SOT-223 Package

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Layout Guidelines (continued)

11.1.1.2.2 Heatsinking the TO-263 (KTT) Package

Figure 39 shows for the TO-263 the measured values of RθJA for different copper area sizes using a typical PCB

with 1-oz. copper and no solder mask over the copper area used for heatsinking.

As shown in Figure 39, increasing the copper area beyond 1 square inch produces very little improvement. It

must also be observed that the minimum value of RθJA for the TO-263 package mounted to a PCB is 32°C/W.

Figure 39. RθJA vs Copper (1-oz.) Area for the TO-263 Package

As a design aid, Figure 40 shows the maximum allowable power dissipation compared to ambient temperature

for the TO-263 device (assuming RθJA is 35°C/W and the maximum junction temperature is 125°C).

Figure 40. Maximum Power Dissipation vs TAMB for the TO-263 Package

11.1.1.2.3 Heatsinking the TO-252 (NDP) Package

If the maximum allowable value for RθJA is found to be ≥54°C/W (typical rated value) for the TO-252 package, no

heatsink is needed because the package alone will dissipate enough heat to satisfy these requirements. If the

calculated value for RθJA falls below these limits, a heatsink is required.

As a design aid, Table 1 shows the value of the RθJA of NDP the package for different heatsink area. The copper

patterns that we used to measure these RθJAs are shown in Figure 45.Figure 41 reflects the same test results as

what are in Table 1.

Figure 42 shows the maximum allowable power dissipation versus ambient temperature for the TO-252 device.

Figure 43 shows the maximum allowable power dissipation versus copper area (in2) for the TO-252 device. See

the AN-1028 Maximum Power Enhancement Techniques for Power Packages application note for thermal

enhancement techniques to be used with SOT-223 and TO-252 packages.

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Layout Guidelines (continued)

(1) Tab of device attached to topside of copper.

Table 1. RθJA Different Heatsink Area

LAYOUT COPPER AREA THERMAL RESISTANCE

Top Side (in2)(1) Bottom Side (in2) (RθJA°C/W) TO-252

1 0.0123 0 103

2 0.066 0 87

3 0.3 0 60

4 0.53 0 54

5 0.76 0 52

6 1.0 0 47

7 0.066 0.2 84

8 0.066 0.4 70

9 0.066 0.6 63

10 0.066 0.8 57

11 0.066 1.0 57

12 0.066 0.066 89

13 0.175 0.175 72

14 0.284 0.284 61

15 0.392 0.392 55

16 0.5 0.5 53

Figure 41. RθJA vs 2-oz. Copper Area for TO-252 Figure 42. Maximum Allowable Power Dissipation vs

Ambient Temperature for TO-252

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

Figure 43. Maximum Allowable Power Dissipation vs 2-oz. Copper Area for TO-252

Figure 44. Top View of the Thermal Test Pattern in Actual Scale

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Figure 45. Bottom View of the Thermal Test Pattern in Actual Scale

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

11.2 Layout Examples

Figure 46. Layout Example (SOT-223)

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

Layout Examples (continued)

Figure 47. Layout Example (TO-220)

LM117

LM317-N

SNVS774Q –MAY 2004–REVISED JUNE 2020

www.ti.com

Product Folder Links: LM117 LM317-N

12 Device and Documentation Support

12.1 Documentation Support

12.1.1 Related Documentation

For related documentation see the following:

• Texas Instruments, LM150/LM350A/LM350 3-Amp Adjustable Regulators data sheet

• Texas Instruments, LM138 and LM338 5-Amp Adjustable Regulators data sheet

• Texas Instruments, LM137, LM337-N 3-Terminal Adjustable Negative Regulators data sheet

• Texas Instruments, LM117QML 3-Terminal Adjustable Regulator data sheet

• Texas Instruments, LM117JAN 3-Terminal Adjustable Regulator data sheet

• Texas Instruments, AN-1028 Maximum Power Enhancement Techniques for Power Packages application

note

12.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to order now.

Table 2. Related Links

PARTS PRODUCT FOLDER ORDER NOW TECHNICAL

DOCUMENTS TOOLS &

SOFTWARE SUPPORT &

COMMUNITY

LM117 Click here Click here Click here Click here Click here

LM317-N Click here Click here Click here Click here Click here

12.3 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper

right corner, click on Alert me to register and receive a weekly digest of any product information that has

changed. For change details, review the revision history included in any revised document.

12.4 Support Resources

TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight

from the experts. Search existing answers or ask your own question to get the quick design help you need.

Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do

not necessarily reflect TI's views; see TI's Terms of Use.

12.5 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.6 Electrostatic Discharge Caution

This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.

ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more

susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

12.7 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

LM117

LM317-N

www.ti.com

SNVS774Q –MAY 2004–REVISED JUNE 2020

Product Folder Links: LM117 LM317-N

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 9-Jun-2020

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM117H ACTIVE TO NDT 3 500 Green (RoHS

& no Sb/Br) AU Level-1-NA-UNLIM -55 to 150 ( LM117HP+, LM117H

P+)

LM117H/NOPB ACTIVE TO NDT 3 500 Green (RoHS

& no Sb/Br) AU Level-1-NA-UNLIM -55 to 150 ( LM117HP+, LM117H

P+)

LM117K ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI -55 to 125 LM117K

STEELP+

LM117K STEEL ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI -55 to 150 LM117K

STEELP+

LM117K STEEL/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS

& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 150 LM117K

STEELP+

LM317EMP NRND SOT-223 DCY 4 1000 TBD Call TI Call TI 0 to 125 N01A

LM317EMP/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM 0 to 125 N01A

LM317EMPX/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM 0 to 125 N01A

LM317H ACTIVE TO NDT 3 500 Green (RoHS

& no Sb/Br) AU Level-1-NA-UNLIM 0 to 0 ( LM317HP+, LM317H

P+)

LM317H/NOPB ACTIVE TO NDT 3 500 Green (RoHS

& no Sb/Br) AU Level-1-NA-UNLIM 0 to 0 ( LM317HP+, LM317H

P+)

LM317MDT/NOPB ACTIVE TO-252 NDP 3 75 Green (RoHS

& no Sb/Br) SN Level-2-260C-1 YEAR 0 to 125 LM317

MDT

LM317MDTX/NOPB ACTIVE TO-252 NDP 3 2500 Green (RoHS

& no Sb/Br) SN Level-2-260C-1 YEAR 0 to 125 LM317

MDT

LM317S/NOPB ACTIVE DDPAK/

TO-263 KTT 3 45 Green (RoHS

& no Sb/Br) SN Level-3-245C-168 HR 0 to 125 LM317S

P+

LM317SX/NOPB ACTIVE DDPAK/

TO-263 KTT 3 500 Green (RoHS

& no Sb/Br) SN Level-3-245C-168 HR 0 to 125 LM317S

P+

LM317T NRND TO-220 NDE 3 45 TBD Call TI Call TI LM317T P+

LM317T/LF01 ACTIVE TO-220 NDG 3 45 Green (RoHS

& no Sb/Br) SN Level-4-260C-72 HR LM317T P+

LM317T/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS

& no Sb/Br) SN Level-1-NA-UNLIM 0 to 125 LM317T P+

(1) The marketing status values are defined as follows:

PACKAGE OPTION ADDENDUM

www.ti.com 9-Jun-2020

Addendum-Page 2

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM317EMP SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LM317EMP/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LM317EMPX/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LM317MDTX/NOPB TO-252 NDP 3 2500 330.0 16.4 6.9 10.5 2.7 8.0 16.0 Q2

LM317SX/NOPB DDPAK/

TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

PACKAGE MATERIALS INFORMATION

www.ti.com 12-May-2020

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM317EMP SOT-223 DCY 4 1000 367.0 367.0 35.0

LM317EMP/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0

LM317EMPX/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0

LM317MDTX/NOPB TO-252 NDP 3 2500 367.0 367.0 38.0

LM317SX/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0

PACKAGE MATERIALS INFORMATION

www.ti.com 12-May-2020

Pack Materials-Page 2

MECHANICAL DATA

NDS0002A

www.ti.com

MECHANICAL DATA

MPDS094A – APRIL 2001 – REVISED JUNE 2002

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE

4202506/B 06/2002

6,30 (0.248)

6,70 (0.264)

2,90 (0.114)

3,10 (0.122)

6,70 (0.264)

7,30 (0.287) 3,70 (0.146)

3,30 (0.130)

0,02 (0.0008)

0,10 (0.0040)

1,50 (0.059)

1,70 (0.067)

0,23 (0.009)

0,35 (0.014)

1 2 3

0,66 (0.026)

0,84 (0.033)

1,80 (0.071) MAX

Seating Plane

0°–10°

Gauge Plane

0,75 (0.030) MIN

0,25 (0.010)

0,08 (0.003)

0,10 (0.004) M

2,30 (0.091)

4,60 (0.181) M

0,10 (0.004)

NOTES: A. All linear dimensions are in millimeters (inches).

B. This drawing is subject to change without notice.

C. Body dimensions do not include mold flash or protrusion.

D. Falls within JEDEC TO-261 Variation AA.

MECHANICAL DATA

NDG0003F

www.ti.com

T03F (Rev B)

www.ti.com

PACKAGE OUTLINE

10.42

9.40

6.73

6.35

6.22

5.97 1.27

0.88

5.46

4.96

2.285

4.57

1.02

0.64

3X 0.88

0.64

2.55 MAX

0.88

0.46

1.14

0.89

0.60

0.46

0.17

0.51 MIN

4.32 MIN

(2.345)

(2.5)

TO-252 - 2.55 mm max heightNDP0003B

TRANSISTOR OUTLINE

4219870/A 03/2018

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. Reference JEDEC registration TO-252.

0.25 C A B

TOP & BOTTOM

PKG

OPTIONAL

SEATING PLANE

SCALE 1.500

www.ti.com

EXAMPLE BOARD LAYOUT

0.07 MAX

ALL AROUND 0.07 MIN

ALL AROUND

(4.57)

2X (1.3) 2X (2.15) (5.7)

(5.5)

(2.285)(4.38)

(R0.05) TYP

TO-252 - 2.55 mm max heightNDP0003B

TRANSISTOR OUTLINE

4219870/A 03/2018

NOTES: (continued)

4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature numbers

SLMA002(www.ti.com/lit/slm002) and SLMA004 (www.ti.com/lit/slma004).

5. Vias are optional depending on application, refer to device data sheet. It is recommended that vias under paste be filled, plugged or tented.

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE: 8X

SYMM

PKG

SEE SOLDER MASK

DETAIL

EXPOSED

METAL

METAL EDGE

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

(PREFERRED) SOLDER MASK DETAIL

EXPOSED

METAL

METAL UNDER

SOLDER MASK

OPENING

SOLDER MASK DEFINED

www.ti.com

EXAMPLE STENCIL DESIGN

2X (2.15)

2X (1.3)

(4.57)

(4.38)

(1.32) TYP

(1.35) TYP

(0.26) (R0.05) TYP

16X (1.12)

16X (1.15)

TO-252 - 2.55 mm max heightNDP0003B

TRANSISTOR OUTLINE

4219870/A 03/2018

NOTES: (continued)

6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

7. Board assembly site may have different recommendations for stencil design.

PKG

SOLDER PASTE EXAMPLE

BASED ON 0.125 MM THICK STENCIL

SCALE: 8X

MECHANICAL DATA

NDT0003A

www.ti.com

H03A (Rev D)

MECHANICAL DATA

NDE0003B

www.ti.com

MECHANICAL DATA

KTT0003B

www.ti.com

BOTTOM SIDE OF PACKAGE

TS3B (Rev F)

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third

party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,

damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on

ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable

warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265