74ALVC164245 16-bit dual supply translating transceiver; 3-state Rev. 8 -- 15 March 2012 Product data sheet 1. General description The 74ALVC164245 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The 74ALVC164245 is a 16-bit (dual octal) dual supply translating transceiver featuring non-inverting 3-state bus compatible outputs in both send and receive directions. It is designed to interface between a 3 V and 5 V bus in a mixed 3 V and 5 V supply environment. This device can be used as two 8-bit transceivers or one 16-bit transceiver. The direction control inputs (1DIR and 2DIR) determine the direction of the data flow. nDIR (active HIGH) enables data from nAn ports to nBn ports. nDIR (active LOW) enables data from nBn ports to nAn ports. The output enable inputs (1OE and 2OE), when HIGH, disable both nAn and nBn ports by placing them in a high-impedance OFF-state. Pins nAn, nOE and nDIR are referenced to VCC(A) and pins nBn are referenced to VCC(B). In suspend mode, when one of the supply voltages is zero, there will be no current flow from the non-zero supply towards the zero supply. The nAn-outputs must be set 3-state and the voltage on the A-bus must be smaller than Vdiode (typical 0.7 V). VCC(B) VCC(A) (except in suspend mode). 2. Features and benefits 5 V tolerant inputs/outputs for interfacing with 5 V logic Wide supply voltage range: 3 V port (VCC(A)): 1.5 V to 3.6 V 5 V port (VCC(B)): 1.5 V to 5.5 V CMOS low power consumption Direct interface with TTL levels Control inputs voltage range from 2.7 V to 5.5 V Inputs accept voltages up to 5.5 V High-impedance outputs when VCC(A) or VCC(B) = 0 V Complies with JEDEC standard JESD8-B/JESD36 ESD protection: HBM JESD22-A114F exceeds 2000 V MM JESD22-A115-A exceeds 200 V Specified from 40 C to +85 C and 40 C to +125 C 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 3. Ordering information Table 1. Ordering information Type number Temperature range Package Name Description Version 40 C to +125 C SSOP48 plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1 74ALVC164245DGG 40 C to +125 C TSSOP48 plastic thin shrink small outline package; 48 leads; SOT362-1 body width 6.1 mm 40 C to +125 C HXQFN60 plastic compatible thermal enhanced extremely thin quad flat package; no leads; 60 terminals; body 4 6 0.5 mm 74ALVC164245DL 74ALVC164245BX SOT1134-2 4. Functional diagram 2DIR 1DIR 2OE 1OE 2A0 1A0 1B0 1A1 2B0 2A1 2B1 1B1 1A2 2A2 1B2 1A3 2B2 2A3 1B3 1A4 2B3 2A4 2B4 1B4 1A5 2A5 1B5 1A6 2B5 2A6 1B6 2B6 2A7 1A7 1B7 2B7 001aaa789 Fig 1. Logic symbol 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 2 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 1OE 1DIR 2OE 2DIR 1A0 G3 3EN1[BA] 3EN2[AB] G6 6EN1[BA] 6EN2[AB] 1B0 1 2 1A1 1B1 1A2 1B2 1A3 1B3 1A4 1B4 1A5 1B5 1A6 1B6 1A7 1B7 2A0 2B0 4 5 2A1 2B1 2A2 2B2 2A3 2B3 2A4 2B4 2A5 2B5 2A6 2B6 2A7 2B7 001aaa790 Fig 2. IEC logic symbol 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 3 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 5. Pinning information 5.1 Pinning 1DIR 1 48 1OE 1B0 2 47 1A0 1B1 3 46 1A1 GND 4 45 GND 1B2 5 44 1A2 1B3 6 43 1A3 VCC(B) 7 42 VCC(A) 1B4 8 41 1A4 1B5 9 40 1A5 GND 10 39 GND 1B6 11 38 1A6 1B7 12 2B0 13 37 1A7 74ALVC164245 36 2A0 2B1 14 35 2A1 GND 15 34 GND 2B2 16 33 2A2 2B3 17 32 2A3 VCC(B) 18 31 VCC(A) 2B4 19 30 2A4 2B5 20 29 2A5 GND 21 28 GND 2B6 22 27 2A6 2B7 23 26 2A7 2DIR 24 25 2OE 001aab037 Fig 3. Pin configuration SOT370-1 (SSOP48) and SOT362-1 (TSSOP48) 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 4 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state terminal 1 index area D1 A32 A1 D5 A31 A30 B20 A29 B19 A28 B18 A27 D4 D8 A26 A2 A25 B1 B17 B2 B16 A3 A24 A4 A23 B15 B3 A5 A22 74ALVC164245 B4 B14 A6 A21 B5 B13 B6 B12 A20 A7 A8 A19 B7 B11 GND(1) A9 A10 D6 D2 A11 B8 A12 B9 A13 A18 B10 A14 A15 D7 A17 A16 D3 001aai851 Transparent top view (1) This is not a supply pin, the substrate is attached to this pad using conductive die attach material. There is no electrical or mechanical requirement to solder this pad however if it is soldered the solder land should remain floating or be connected to GND. Fig 4. Pin configuration SOT1134-2 (HXQFN60) 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 5 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 5.2 Pin description Table 2. Pin description Symbol Pin Description SOT370-1 and SOT362-1 SOT1134-2 1DIR, 2DIR 1, 24 A30, A13 direction control input 1B0 to 1B7 2, 3, 5, 6, 8, 9, 11, 12 B20, A31, D5, D1, A2, B2, B3, A5 data input/output 2B0 to 2B7 13, 14, 16, 17, 19, 20, 22, 23 A6, B5, B6, A9, D2, D6, A12, B8 data input/output GND 4, 10, 15, 21, 28, 34, 39, 45 A32, A3, A8, A11, A16, A19, A24, A27 ground (0 V) VCC(B) 7, 18 A1, A10, supply voltage B (5 V bus) 1OE, 2OE 48, 25 A29, A14 output enable input (active LOW) 1A0 to 1A7 47, 46, 44, 43, 41, 40, 38, 37 B18, A28, D8, D4, A25, B16, B15, A22 data input/output 2A0 to 2A7 36, 35, 33, 32, 30, 29, 27, 26 A21, B13, B12, A18, D3, D7, A15, B10 data input/output VCC(A) 31, 42 A17, A26 supply voltage A (3 V bus) n.c. - A4, A7, A20, A23, B1, B4, B7, B9, B11, B14, B17, B19 not connected 6. Functional description Table 3. Function table[1] Inputs Outputs nOE nDIR nAn nBn L L nAn = nBn inputs L H inputs nBn = nAn H X Z Z [1] H = HIGH voltage level; L = LOW voltage level; X = don't care; Z = high-impedance OFF-state. 7. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). See [1]. Symbol Parameter Conditions Min Max Unit VCC(B) supply voltage B VCC(B) VCC(A) 0.5 +6.0 V VCC(A) supply voltage A VCC(B) VCC(A) 0.5 +4.6 V IIK input clamping current VI < 0 V 50 - mA 0.5 +6.0 V 0.5 VCC + 0.5 V - 50 mA output HIGH or LOW [2] 0.5 VCC + 0.5 V output 3-state [2] 0.5 +6.0 V - 50 mA - 100 mA VI input voltage VI/O input/output voltage IOK output clamping current VO output voltage IO(sink/source) output sink or source current ICC supply current 74ALVC164245 Product data sheet [2] VO > VCC or VO < 0 V VO = 0 V to VCC All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 6 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state Table 4. Limiting values ...continued In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). See [1]. Symbol Parameter IGND ground current Tstg storage temperature Ptot total power dissipation Conditions Min Max Unit 100 - mA 65 +150 C Tamb = 40 C to +125 C (T)SSOP48 package [3] - 500 mW HXQFN60 package [4] - 1000 mW [1] The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 C. [2] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [3] Above 60 C the value of Ptot derates linearly with 5.5 mW/K. [4] Above 70 C the value of Ptot derates linearly with 1.8 mW/K. 8. Recommended operating conditions Table 5. Recommended operating conditions Symbol Parameter Conditions VCC(B) supply voltage B VCC(B) VCC(A) VCC(A) supply voltage A Min Typ Max Unit maximum speed performance 2.7 - 5.5 V low-voltage applications 1.5 - 5.5 V maximum speed performance 2.7 - 3.6 V low-voltage applications 1.5 - 3.6 V VCC(B) VCC(A) VI input voltage control inputs: nOE and nDIR 0 - 5.5 V VI/O input/output voltage nAn port 0 - VCC(A) V nBn port 0 - VCC(B) V VO output voltage nAn port 0 - VCC(A) V nBn port 0 - VCC(B) V 40 - +125 C Tamb ambient temperature t/V input transition rise and fall rate 74ALVC164245 Product data sheet VCC(A) = 2.7 V to 3.0 V 0 - 20 ns/V VCC(A) = 3.0 V to 3.6 V 0 - 10 ns/V VCC(B) = 3.0 V to 4.5 V 0 - 20 ns/V VCC(B) = 4.5 V to 5.5 V 0 - 10 ns/V All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 7 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 9. Static characteristics Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VIH HIGH-level input voltage Tamb = 40 C to +85 C Conditions Tamb = 40 C to +125 C Unit Min Typ[1] Max Min Typ[1] Max 2.0 - - 2.0 - - V nBn port VCC(B) = 3.0 V to 5.5 V [2] nAn port, nOE and nDIR VCC(A) = 3.0 V to 3.6 V 2.0 - - 2.0 - - V [2] 1.7 - - 1.7 - - V VCC(B) = 4.5 V to 5.5 V [2] - - 0.8 - - 0.8 V VCC(B) = 3.0 V to 3.6 V [2] - - 0.7 - - 0.7 V - - 0.8 - - 0.8 V - - 0.7 - - 0.7 V HIGH-level nBn port; VI = VIH or VIL output voltage IO = 24 mA; VCC(B) = 4.5 V VCC(B) 0.8 - - VCC(B) 1.2 - - V IO = 12 mA; VCC(B) = 4.5 V VCC(B) 0.5 - - VCC(B) 0.8 - - V IO = 18 mA; VCC(B) = 3.0 V VCC(B) 0.8 - - VCC(B) 1.0 - - V IO = 100 A; VCC(B) = 3.0 V VCC(B) 0.2 VCC(B) - VCC(B) 0.3 VCC(B) - V IO = 24 mA; VCC(A) = 3.0 V VCC(A) 0.7 - - VCC(A) 1.0 - - V IO = 100 A; VCC(A) = 3.0 V VCC(A) 0.2 - - VCC(A) 0.3 - - V IO = 12 mA; VCC(A) = 2.7 V VCC(A) 0.5 - - VCC(A) 0.8 - - V IO = 8 mA; VCC(A) = 2.3 V VCC(A) 0.6 - - VCC(A) 0.6 - IO = 100 A; VCC(A) = 2.3 V VCC(A) 0.2 VCC(A) - VCC(A) 0.3 VCC(A) VCC(A) = 2.3 V to 2.7 V VIL LOW-level input voltage nBn port nAn port, nOE and nDIR VCC(A) = 3.0 V to 3.6 V VCC(A) = 2.3 V to 2.7 V VOH [2] nAn port; VI = VIH or VIL VOL - V - V LOW-level nBn port; VI = VIH or VIL output voltage IO = 24 mA; VCC(B) = 4.5 V - - 0.55 - - 0.60 V IO = 12 mA; VCC(B) = 4.5 V - - 0.40 - - 0.80 V IO = 100 A; VCC(B) = 4.5 V - - 0.20 - - 0.30 V IO = 18 mA; VCC(B) = 3.0 V - - 0.55 - - 0.80 V IO = 100 A; VCC(B) = 3.0 V - - 0.20 - - 0.30 V IO = 24 mA; VCC(A) = 3.0 V - - 0.55 - - 0.80 V IO = 100 A; VCC(A) = 3.0 V - - 0.20 - - 0.30 V IO = 12 mA; VCC(A) = 2.7 V - - 0.40 - - 0.60 V IO = 12 mA; VCC(A) = 2.3 V - - 0.60 - - 0.60 V IO = 100 A; VCC(A) = 2.3 V - - 0.20 - - 0.20 V - 0.1 5 - 0.1 10 A - 0.1 10 - 0.1 20 A nAn port; VI = VIH or VIL II input leakage current IOZ OFF-state VI = VIH or VIL; output current VO = VCC or GND 74ALVC164245 Product data sheet VI = 5.5 V or GND [3] All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 8 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state Table 6. Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter ICC Tamb = 40 C to +85 C Conditions additional per control pin; supply current VI = VCC 0.6 V; IO = 0 A CI input capacitance CI/O input/output capacitance [1] Min Max Min Typ[1] Max - 0.1 40 - 0.1 80 - 5 500 - 5 - 4.0 - - - - pF - 5.0 - - - - pF supply current VI = VCC or GND; IO = 0 A ICC Tamb = 40 C to +125 C Unit Typ[1] [4] nAn and nBn port A 5000 A All typical values are measured at VCC(B) = 5.0 V, VCC(A) = 3.3 V and Tamb = 25 C. [2] If VCC(A) < 2.7 V, the switching levels at all inputs are not TTL compatible. [3] For transceivers, the parameter IOZ includes the input leakage current. [4] VCC(A) = 2.7 V to 3.6 V: other inputs at VCC(A) or GND; VCC(B) = 4.5 V to 5.5 V: other inputs at VCC(B) or GND. 10. Dynamic characteristics Table 7. Dynamic characteristics GND = 0 V; tr = tf 2.5 ns; CL = 50 pF; for test circuit see Figure 7. Symbol Parameter tpd propagation delay Tamb = 40 C to +85 C Conditions Product data sheet Unit Typ[1] Max Min Max VCC(A) = 2.3 V to 2.7 V; VCC(B) = 3.0 V to 3.6 V 1.5 3.3 7.6 1.5 9.5 ns VCC(A) = 2.7 V; VCC(B) = 4.5 V to 5.5 V 1.0 3.0 5.9 1.0 7.5 ns VCC(A) = 3.0 V to 3.6 V; VCC(B) = 4.5 V to 5.5 V 1.0 2.9 5.8 1.0 7.5 ns VCC(A) = 2.3 V to 2.7 V; VCC(B) = 3.0 V to 3.6 V 1.0 3.0 7.6 1.0 9.5 ns VCC(A) = 2.7 V; VCC(B) = 4.5 V to 5.5 V 1.0 4.3 6.7 1.0 8.5 ns VCC(A) = 3.0 V to 3.6 V; VCC(B) = 4.5 V to 5.5 V 1.2 2.5 5.8 1.2 7.5 ns nAn to nBn; see Figure 5 nBn to nAn; see Figure 5 74ALVC164245 Tamb = 40 C to +125 C Min [2] [2] All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 9 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state Table 7. Dynamic characteristics ...continued GND = 0 V; tr = tf 2.5 ns; CL = 50 pF; for test circuit see Figure 7. Symbol Parameter ten enable time Tamb = 40 C to +85 C Conditions disable time Max Min Max VCC(A) = 2.3 V to 2.7 V; VCC(B) = 3.0 V to 3.6 V 1.5 4.1 11.5 1.5 14.5 ns VCC(A) = 2.7 V; VCC(B) = 4.5 V to 5.5 V 1.5 3.6 9.2 1.5 11.5 ns VCC(A) = 3.0 V to 3.6 V; VCC(B) = 4.5 V to 5.5 V 1.0 3.2 8.9 1.0 12.0 ns VCC(A) = 2.3 V to 2.7 V; VCC(B) = 3.0 V to 3.6 V 1.5 4.6 12.3 1.5 15.5 ns VCC(A) = 2.7 V; VCC(B) = 4.5 V to 5.5 V 1.5 4.3 9.3 1.5 12.0 ns VCC(A) = 3.0 V to 3.6 V; VCC(B) = 4.5 V to 5.5 V 1.0 3.2 8.9 1.0 11.5 ns VCC(A) = 2.3 V to 2.7 V; VCC(B) = 3.0 V to 3.6 V 2.0 2.7 10.5 2.0 13.5 ns VCC(A) = 2.7 V; VCC(B) = 4.5 V to 5.5 V 2.5 4.6 9.0 2.5 11.5 ns VCC(A) = 3.0 V to 3.6 V; VCC(B) = 4.5 V to 5.5 V 2.1 4.9 8.6 2.1 11.0 ns VCC(A) = 2.3 V to 2.7 V; VCC(B) = 3.0 V to 3.6 V 1.0 2.7 9.3 1.0 12.0 ns VCC(A) = 2.7 V; VCC(B) = 4.5 V to 5.5 V 1.5 3.5 9.0 1.5 11.5 ns VCC(A) = 3.0 V to 3.6 V; VCC(B) = 4.5 V to 5.5 V 2.0 3.2 8.6 2.0 11.0 ns nOE to nBn; see Figure 6 nOE to nBn; see Figure 6 nOE to nAn; see Figure 6 74ALVC164245 Product data sheet Unit Min nOE to nAn; see Figure 6 tdis Tamb = 40 C to +125 C Typ[1] [2] [2] [2] [2] All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 10 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state Table 7. Dynamic characteristics ...continued GND = 0 V; tr = tf 2.5 ns; CL = 50 pF; for test circuit see Figure 7. Symbol Parameter CPD power dissipation capacitance Tamb = 40 C to +85 C Conditions Min Max Min Max - 30 - - - pF - 15 - - - pF outputs enabled - 40 - - - pF outputs disabled - 5 - - - pF 5 V port: nAn to nBn; VCC(B) = 5 V; VCC(A) = 3.3 V outputs enabled 3 V port: nBn to nAn; VCC(B) = 5 V; VCC(A) = 3.3 V [2] Unit [3][4] outputs disabled [1] Tamb = 40 C to +125 C Typ[1] [3][4] All typical values are measured at nominal voltage for VCC(B) and VCC(A) and at Tamb = 25 C. tpd is the same as tPLH and tPHL. ten is the same as tPZL and tPZH. tdis is the same as tPLZ and tPHZ. [3] CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD VCC2 fi N + (CL VCC2 fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; (CL VCC2 fo) = sum of outputs. [4] The condition is VI = GND to VCC. 11. AC waveforms VI nAn, nBn input VM GND tPHL tPLH VOH nBn, nAn output VM VOL 001aaa792 Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with the output load. Fig 5. Input (nAn, nBn) to output (nBn, nAn) propagation delays 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 11 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state VI nOE input VM GND tPLZ tPZL VCC output LOW-to-OFF OFF-to-LOW VM VX VOL tPHZ VOH tPZH VY output HIGH-to-OFF OFF-to-HIGH GND VM outputs enabled outputs enabled outputs disabled mna362 Measurement points are given in Table 8. VOL and VOH are typical output voltage levels that occur with output load. Fig 6. Table 8. 3-state enable and disable times Measurement points Direction Supply voltage Input VCC(A) VI VM VCC(B) Output VM VX VY VOL(B) + 0.3 V VOH(B) 0.3 V nAn port to nBn port 2.3 V to 2.7 V 2.7 V to 3.6 V VCC(A) 0.5 VCC(A) 1.5 V nBn port to nAn port 2.3 V to 2.7 V 2.7 V to 3.6 V 2.7 V 1.5 V 0.5 VCC(A) VOL(A) + 0.15 V VOH(A) 0.15 V nAn port to nBn port 2.7 V to 3.6 V 4.5 V to 5.5 V 2.7 V 1.5 V 0.5 VCC(B) 0.2 VCC(B) 0.8 VCC(B) nBn port to nAn port 2.7 V to 3.6 V 4.5 V to 5.5 V 3.0 V 1.5 V 1.5 V VOH(A) 0.3 V 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 VOL(A) + 0.3 V (c) NXP B.V. 2012. All rights reserved. 12 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state VEXT VCC VI RL VO G DUT RT CL RL mna616 Test data is given in Table 9. Definitions for test circuit: RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. RL = Load resistance. Fig 7. Table 9. Test circuit for measuring switching times Test data Direction Supply voltage Load VEXT VCC(A) VCC(B) CL RL tPLH, tPHL tPZH, tPHZ tPZL, tPLZ nAn port to nBn port 2.3 V to 2.7 V 2.7 V to 3.6 V 50 pF 500 open GND 2 VCC nBn port to nAn port 2.3 V to 2.7 V 2.7 V to 3.6 V 50 pF 500 open GND 6.0 V nAn port to nBn port 2.7 V to 3.6 V 4.5 V to 5.5 V 50 pF 500 open GND 2 VCC nBn port to nAn port 2.7 V to 3.6 V 4.5 V to 5.5 V 50 pF 500 open GND 6.0 V 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 13 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 12. Package outline SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1 D E A X c y HE v M A Z 25 48 Q A2 A1 A (A 3) pin 1 index Lp L 24 1 detail X w M bp e 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 2.8 0.4 0.2 2.35 2.20 0.25 0.3 0.2 0.22 0.13 16.00 15.75 7.6 7.4 0.635 10.4 10.1 1.4 1.0 0.6 1.2 1.0 0.25 0.18 0.1 0.85 0.40 8o o 0 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT370-1 Fig 8. REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-118 Package outline SOT370-1 (SSOP48) 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 14 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 E D A X c HE y v M A Z 48 25 Q A2 (A 3) A1 pin 1 index A Lp L 1 detail X 24 w M bp e 2.5 0 5 mm scale DIMENSIONS (mm are the original dimensions). UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z mm 1.2 0.15 0.05 1.05 0.85 0.25 0.28 0.17 0.2 0.1 12.6 12.4 6.2 6.0 0.5 8.3 7.9 1 0.8 0.4 0.50 0.35 0.25 0.08 0.1 0.8 0.4 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT362-1 Fig 9. REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-153 Package outline SOT362-1 (TSSOP48) 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 15 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state HXQFN60: plastic compatible thermal enhanced extremely thin quad flat package; no leads; 60 terminals; body 4 x 6 x 0.5 mm A B D SOT1134-2 terminal 1 index area A A2 E A1 detail X e2 b e1 L1 L A11 B10 A17 A10 eR eT y y1 C D3 D7 A16 B8 C eT 1/2 e D2 D6 C A B C eR e C A B C v w v w e B11 B7 Eh e3 e4 1/2 e B17 B1 A1 terminal 1 index area A26 D5 D1 A32 B20 B18 A27 Dh D8 D4 eT eR X K eT eR 0 5 mm Dimensions Unit A A1 A2 b max 0.50 0.08 0.42 0.28 nom 0.05 0.40 0.23 min 0.02 0.38 0.18 mm D Dh E Eh e e1 e2 e3 e4 eR 4.1 4.0 3.9 1.95 1.85 1.75 6.1 6.0 5.9 3.95 3.85 3.75 0.5 1.0 2.5 3.0 4.5 0.5 eT K L L1 v w 0.25 0.28 0.195 0.49 0.20 0.23 0.145 0.1 0.15 0.18 0.095 y 0.05 0.08 y1 0.1 sot1134-2_po References Outline version IEC JEDEC JEITA SOT1134-2 --- --- --- European projection Issue date 11-08-15 Fig 10. Package outline SOT1134-2 (HXQFN60) 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 16 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 13. Abbreviations Table 10. Abbreviations Acronym Description CMOS Complementary Metal Oxide Semiconductor DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model TTL Transistor-Transistor Logic 14. Revision history Table 11. Revision history Document ID Release date Data sheet status Change notice Supersedes 74ALVC164245 v.8 20120315 Product data sheet - 74ALVC164245 v.7 Modifications: 74ALVC164245 v.7 Modifications: * For type number 74ALVC164245BX the sot code has changed to SOT1134-2. 20111117 * Product data sheet - 74ALVC164245 v.6 Legal pages updated. 74ALVC164245 v.6 20110616 Product data sheet - 74ALVC164245 v.5 74ALVC164245 v.5 20100413 Product data sheet - 74ALVC164245 v.4 74ALVC164245 v.4 20081111 Product data sheet - 74ALVC164245 v.3 74ALVC164245 v.3 20040914 Product data sheet - 74ALVC164245 v.2 74ALVC164245 v.2 20040601 Product data sheet - 74ALVC164245 v.1 74ALVC164245 v.1 19980826 Product specification - - 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 17 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 15. Legal information 15.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 15.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 15.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. 74ALVC164245 Product data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 18 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 15.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com 74ALVC164245 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 15 March 2012 (c) NXP B.V. 2012. All rights reserved. 19 of 20 74ALVC164245 NXP Semiconductors 16-bit dual supply translating transceiver; 3-state 17. Contents 1 2 3 4 5 5.1 5.2 6 7 8 9 10 11 12 13 14 15 15.1 15.2 15.3 15.4 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 Functional description . . . . . . . . . . . . . . . . . . . 6 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Recommended operating conditions. . . . . . . . 7 Static characteristics. . . . . . . . . . . . . . . . . . . . . 8 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Contact information. . . . . . . . . . . . . . . . . . . . . 19 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 15 March 2012 Document identifier: 74ALVC164245