XWD24059 - Power-One - Datasheet.Directory

REV. NOV 03, 2003

XWD DC-DC Series Data Sheet

Dual-Output, 180 Watts

Page 1 of 3

XWD dual-output DC-DC converters are high powered converters that cover a wide range of applications. Available

input voltages include 12V, 24V, 40V, and 48V. Output voltages are available from 5V to 15V. The XWD features

remote sense leads for accurate point of load regulation. For single and triple-output high power

solutions, see the XWS and XWT Series of converters.

• High power package

• Wide input range

• Trim and enable

• Remote Sense Pins

• 500V Isolation

Description

Features

Output

Setpoint Accuracy ±1%

Line Regulation VinMin. - VinMax., IoutRated ±1% Vout

Load Regulation IoutMin. - IoutMax., VinNom. ±1% Vout

Minimum Output Current 10 %

Dynamic Regulation, Loadstep 25% Iout

Pk Deviation 4% Vout

Settling Time 500 µs

Voltage Trim Range ±10%

Turn-On Time 10 ms

Remote Shutdown Positive Logic

Switching Frequency 200 kHz

Isolation

Input - Output 500 VDC

Temperature Coefficient ±0.02%/°C

Case Temperature

Operating Range -25 To +85°C††

Storage Range -40 To +125°C

Thermal Shutdown Range 105 - 115°C

Humidity Max., Non-Condensing 95%

Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz

MTBF†(Bellcore TR-NWT-000332) Consult Factory

Safety Consult Factory

Weight (Approx.) 15.4 oz

General

Technical Specifications

Voltage Range

12 VDC Nominal 10 - 20 VDC

24 VDC Nominal 18 - 36 VDC

48 VDC Nominal 36 - 72 VDC

40 VDC Nominal (Wide Input) 20 - 60 VDC

Input Ripple Current 20% Iin Max.

Reverse Input Current 100% Iin Max.

Input

XWD2405

10 20 30 40 50 60 70 80 90 100

LOAD %

EFFICIENCY %

(18v)

(24v)

(36v)

Efficiency vs. Load (24V Input)

10 20 30 40 50 60 70 80 90 100

LOAD %

EFFICIENCY %

XWD4812

XWD4815

Efficiency vs. Load (48V Input)

Notes

† MTBF predictions may vary slightly from model to model.

†† Industrial temp range of -40 to +85°C available.

Specifications typically at 25°C, normal line, and full load, unless otherwise

stated.

Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with

commercial wave-soldering equipment.

Safety: Fusing Recommended.

+ See following two pages for Terminal Strip Option

MODEL INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL

(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS) pk-pk (mV) EFFICIENCY**

XWD1205 12 10-20 14.0 ±5 ±10 50 79%

XWD1212TS 12 10-20 16.9 ±12 ±5.2 120 81%

XWD1215 12 10-20 16.7 ±15 ±4.15 150 82%

XWD2405 24 18-36 11.3 ±5 ±15 50 82%

XWD2412 24 18-36 13.3 ±12 ±7.5 120 83%

XWD2415 24 18-36 13.3 ±15 ±6 150 83%

XWD4805 48 36-72 5.5 ±5 ±15 50 84%

XWD4812 48 36-72 6.5 ±12 ±7.5 120 85%

XWD4815 48 36-72 6.5 ±15 ±6 150 85%

XWD6005 40 20-60 10.3 ±5 ±15 50 80%

XWD6012 40 20-60 12.2 ±12 ±7.5 120 81%

XWD6015 40 20-60 12.2 ±15 ±6 150 81%

NOTES:

* Maximum input current at minimum input voltage, maximum rated output power.

** At nominal Vin, rated output.

REV. NOV 03, 2003

Dual-Output, 180 Watts

Page 2 of 3

XWD DC-DC Series Data Sheet

Mechanical Drawing

Pin Function

1 No Pin

2-V

3-V

4+V

5+V

6 Enable

7 Case

8 -V1 Sense

9 -V1out

10 +V1out

11 +V1 Sense1

12 - V2out

13 Trim

14 + V2out

Tolerances

Inches: (Millimeters)

.XX ± 0.040 .X ± 1.0

.XXX ± 0.010 .XX ± 0.25

Pin:

± 0.002 ± 0.05

(Dimensions as listed unless otherwise

specified.)

#4-40 THREADED INSERTS 4PLS.

5.50"

(139.7mm)

1.875"(47.6mm)

2.250"(57.2mm)

2.625"(66.7mm)

0.750"(19.1mm)

1.125"(28.6mm)

1.500"(38.1mm)

0.375"(9.5mm)

-0.375"(-9.5mm)

-0.625"(-15.9mm)

3.50"

(88.9mm)

BOTTOM VIEW

(23.4mm)

0.92"

(1.0mm)

DIA 0.040" 13PL.

-0.60"

(-15.2mm)

4.300"

(109.2mm)

Note:

Thermal impedance data is dependent on

many environmental factors. The exact

thermal performance should be validated

for specific application.

Thermal Impedance

Natural convection 2.5 °C/W

100 LFM 2.1 °C/W

200 LFM 1.7 °C/W

300 LFM 1.3 °C/W

400 LFM 1.1 °C/W

Model numbers highlighted in yellow or shaded are not recommended for new designs.

Model Selection

REV. NOV 03, 2003

OPTIONS

Page 3 of 3

This page is offered as a reference. Consult factory for actual availability of options. When ordering

equipment options, use the following suffix information. Select preferred option(s) and add the suffix to the

model number. Ordering option examples are located below the options table.

NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems,

equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president

of Power-One, Inc.

TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

OPTION SUFFIX APPLICABLE SERIES REMARKS

Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, TTL "Low" Turns Module ON

QBS, QES, QLS, TES, TQD TTL "High" Turns Module OFF

Lucent-Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES,

QLS

Trim 1 IAS, LES

Enable 2 IAD, IAS, LES, SMS

Trim and Enable 3 IAS, LES

Pin Length and Heat Sink Options Standard Pin Length is 0.180" (4.6mm)

0.110" (2.8mm) Pin Length 8 All Leaded Models

0.150" (3.8mm) Pin Length 9 All Leaded Models

0.24" (6.1mm) Horizontal Heat Sink 1H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad