Model PD4859J5050S2HF Rev B Ultra Low Profile 0805 Power Divider 50 to 50 Description The PD4859J5050S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD4859J5050S2HF is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD4859J5050S2HF is matched to 50 and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: 802.11a, WiMax, and home cordless. The PD4859J5050S2HF does not include the resistive element and therefore, requires an external resistor for operation. The PD4859J5050S2HF is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25C) Features: 4800-5900 MHz 18 dB Isolation (output ports) Good Return Loss 0.5mm Height Profile 50 Ohm Input / 50 Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant External Resistor Required Halogen Free Parameter Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature Min. 4800 Typ. Max 5900 50 50 10.3 0.7 0.1 1 18 7.9 14 Unit MHz dB dB dB Degrees dB Watts C 1.0 0.3 4 2 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 C) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 2.040.10 0.460.05 1 3 2 2x 0.15 1.290.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 5 4 4x 0.65 6x 0.30 Designation GND Input GND Output 1 GND Output 2 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD4859J5050S2HF Rev B Typical Broadband Performance: 500 MHz. to 8.0 GHz. Insertion Loss 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 Amplitude Balance 1.5 15 1 10 0.5 5 Frequency [MHz] Isolation -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 -36 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 8000 7500 7000 6500 6000 5500 Frequency [MHz] 0 [dB] 8000 7500 7000 6500 6000 5500 5000 4500 5000 4500 4000 3500 3000 2500 2000 8000 7500 7000 6500 6000 5500 5000 4500 4000 -20 3500 -2 3000 -15 2500 -1.5 2000 -10 1500 -1 1500 0 -5 1000 0 -0.5 500 deg 20 1000 4000 Phase Balance 2 500 3500 Frequency [MHz] Frequency [MHz] [dB] 3000 2500 2000 0 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -36 3000 -33 -36 2500 -30 -33 2000 -27 -30 1500 -24 -27 1000 -21 -24 1500 -18 -21 1000 -18 500 [dB] -9 500 [dB] Return Loss - Input 0 Model PD4859J5050S2HF Rev B Typical Performance: 4700 MHz. to 6000 MHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 Frequency [MHz] 5900 6000 5900 6000 5500 5400 5300 5200 5100 5000 4900 6000 -20 5900 -2 5800 -15 5700 -1.5 5600 -10 5500 -1 4800 0 -5 4700 0 -0.5 5400 5800 5 5300 5700 0.5 5200 5800 10 5100 5700 1 5000 5600 15 deg 1.5 4900 5500 Phase Balance 20 4800 5600 Amplitude Balance 2 4700 5400 Frequency [MHz] Frequency [MHz] [dB] 5300 5200 5100 4700 6000 5900 5800 5700 5600 5500 5400 5300 -3.6 5200 -3.3 -36 5100 -3.0 -33 5000 -2.7 -30 4900 -2.4 -27 4800 -2.1 -24 5000 -1.8 -21 4900 -18 4800 [dB] 0.0 4700 [dB] Return Loss - Input 0 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 6000 5900 5800 5700 5600 5500 5400 5300 5200 5100 5000 4900 4800 -36 4700 [dB] -15 Frequency [MHz] Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD4859J5050S2HF Rev B Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD4859J5050S2HF is a Wilkinson power divider, an external 0603 100 resistor must be mounted in locations R1 as shown in the Figure below. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. Pad Footprint w/ 0603 Resistor Location Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) 3x Transmission lines Solder Resist 3x Plated thru holes to ground 6x .33 .04 6x .41 4x .25 .66 R1 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model PD4859J5050S2HF Rev B Packaging and Ordering Information Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Visit us at www.anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282