LMG7520RPFC 320*240 Dots
FEATURES
♦ Black on White STN Type
♦ Transmissive Mode
♦ High Brightness Long Lifetime CFL Backlight
♦ Improved Contrast through Smaller Dot Gap
and New LC Material
MECHANICAL DATA
Item Value Unit
Module Dimensions 129.6*92.6*7.5 mm
Viewing Area 100*75.5 mm
Resolution 320*240 dots
Dot Size 0.285*0.285 mm
Dot Pitch 0.3*0.3 mm
Weight 110 g
OPTICAL DATA
Item Symbol Condition Min Typ Max Unit
Contrast Ratio K ¯=10¡,
Q=0¡,
Note 1
-20 - -
Brightness - T=25¡C,
IL=5mA,
Note 7
80.0 100.0 - cd/m2
Viewing
Direction
- 6 oÕclock
Viewing Angle ¯2 - ¯1 K=2,
Note 1
- 40 - degree
Response Time
(Rise)
tR¯=10¡,
Q=0¡,
Note 1
- 110 - ms
Response Time
(Fall)
tF¯=10¡,
Q=0¡,
Note 1
- 160 - ms
ABSOLUTE MAXIMUM RATINGS
Item Symbol Condition Min Max Unit
Supply Voltage
(Logic)
VDD
- VSS - 0 6.5 V
Supply Voltage
(LC Drive)
VDD - VEE - 0 27.5 V
Input Voltage VINote 2 -0.3 0.3+VDD V
Operating
Temperature
TOP Note 5,6 0 50 ¡C
Storage
Temperature
TST Note 5,6 -20 60 ¡C
DATA INTERFACE PIN ASSIGNMENT
Pin No Symbol Level Function
1 FRAME H First Line Marker
2 LOAD H->L Data latch
3 CP H->L Data shift
4 VDD - Power supply for logic
5 VSS - GND
6 VEE - Power supply for LC
7-10 D0-D3 H/L Display data
11 Not DISP OFF H/L High for ON / Low for OFF
12 NC - No connection
CFL INTERFACE PIN ASSIGNMENT
Pin No Symbol Level Function
1 HV - Power supply for CFL
2 NC - No connection
3 NC - No connection
4 GND - CFL Ground
Note1: Definition of optical data, see page 84
Note 2: Applied to NotDISP.OFF, FRAME, LOAD, CP, D0-D3
Note 3: fFRAME=75Hz, D0-D3=0.1.0.1...VDD-VEE=23.0V, T=25¡C
Note 4: Recommended LC driving voltage may fluctuate about +-1.0V by each module
ELECTRICAL CHARACTERISTICS
Item Symbol Condition Min Typ Max Unit
Supply Voltage
(Logic)
VDD
- VSS - 3.0 5.0 5.25 V
Supply Voltage
(LC Drive)
VEE - VSS - - -22.0 - V
Supply Current IDD Note 3 - 8.0 - mA
IEE Note 3 - 6.0 - mA
Input Voltage
(High Level)
VIH High Level,
Note 2
0.8*
VDD
- VDD V
Input Voltage
(Low Level)
VIL Low Level,
Note 2
0 - 0.2*
VDD
V
Frame
Frequency
fFLM Note 8 70 - (140) Hz
Duty Ratio - 1/240 -
Recommended
LC Drive
Voltage
VDD -VODuty=1/240
T=10¡,
¯=10¡,
Note 4
- 24.1 - V
Duty=1/240
T=25¡C,
¯=10¡,
Note 4
- 23.0 - V
Duty=1/240
T=40¡C,
¯=10¡,
Note 4
- 21.6 - V
Backlight Lamp
Voltage
VBL T=25¡C - 300 - Vrms
Backlight Lamp
Frequency
fBL T=25¡C - 70 85 kHz
Backlight Lamp
Current
IBL T=25¡C 4 5 6 mArms
Lamp Start
Voltage
VST=25¡C,
Note 9
(1000) - - V
TIMING CHARACTERISTICS
Item Symbol Min Typ Max Unit
Clock frequency fCP - - 6.5 MHz
Clock pulse width tW 63 - - ns
Rise, Fall time tr, tf - - 20 ns
Data set up time tDSU 50 - - ns
Data hold time tDHD 50 - - ns
LOAD set up time tLSU 80 - - ns
LOAD -> Clock time tLC 80 - - ns
FRAME set up time tsetup 100 - - ns
FRAME hold time thold 100 - - ns
LOAD pulse width twc 125 - - ns
INVERTER AND CONNECTORS
Recommended Inverter Starter Kit
HITACHI INVC304 START7520
Data Connector Data Housing Connector
MOLEX 52103-1217 510-1500
Lamp Connector Lamp Housing Connector
MITSUMI M63M83-04 M61M73-04, M60-04-30-114P or
M60-04-30-134P
Note 5: Background colour of the LCD changes depending on temperature. Between
40-50¡C optical characteristics of the LCD like contast and viewing angle
change but the display remains readable.
Note 6: Storage at -20¡C < 48 hr, at 60¡C < 168 hr
Note 7: Measurement after 10 minutes of CFL operating. Brightness control at 100%
Note 8: Need to make sure of flickering and rippling of display when setting the
FRAME Frequency in your set.
Note 9: Starting discharge voltage is increased when LCM is operating at lower
temperature. Please check the characteristics of inverter before applying.