HDSP-315x/316x/515x/516x Series
10 mm and 13 mm Slim Font Seven Segment Displays
Data Sheet
Features
• Excellent appearance
• Slim font design
• Mitered corners, evenly illuminated segments
• Gray face for optimum on/o contrast
• Choice of colors: DH AlGaAs red, High Eciency Red
(HER), yellow, and green
• Low current available, AlGaAs red and HER choice of
character size: 10 mm and 13 mm
• ±50° viewing angle
• Characterized for luminous intensity
Description
The HDSP-31xx-51xx Series of displays incorporates a new
slim font character design. This slim font features narrow
width, specially mitered segments to give a fuller appear-
ance to the illuminated character. Faces of these displays
are painted a neutral gray for enhanced on/o contrast.
All devices are available in either common anode or
common cathode conguration with right hand decimal
point. Low current versions are available in either AlGaAs
red or HER.
Devices
AlGaAs HER HER Yellow Green
Red Low Std. Low Std. Std.
Current Current Current Current Current Package
HDSP- HDSP- HDSP- HDSP- HDSP- Description Drawing
315H 315E 315L 315Y 315G Common Anode, A
10 mm Display
316H 316E 316L 316Y 316G Common Cathode, B
10 mm Display
515H 515E 515L 515Y 515G Common Anode, A
13 mm Display
516H 516E 516L 516Y 516G Common Cathode, B
13 mm Display
2
Part Numbering System
Notes:
1. For codes not listed in the gure above, please refer to the respective datasheet or
contact your nearest Avago representative for details.
2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically
restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet
for specic bin limit information.
5082 - X X X X - X X X X X
HDSP - X X X X - X X X X X
Mechanical Options[1]
00: No Mechanical Option
Color Bin Options[1,2]
0: No Color Bin Limitation
Maximum Intensity Bin[1,2]
0: No Maximum Intensity Bin Limitation
Minimum Intensity Bin[1,2]
0: No Minimum Intensity Bin Limitation
Device Conguration/Color[1]
H: AlGaAs Red
E: High Eciency Red
G: Green
Y: Yellow
Device Specic Conguration[1]
Refer to Respective Datasheet
Package[1]
Refer to Respective Datasheet
3
HDSP-315x/316x Series
HDSP-515x/516x Series
Notes:
1. Package dimensions in millimeters.
2. Untoleranced dimensions are for reference only.
3. For yellow and green devices only.
10
9.7 ± 0.1
0.3 ± 0.05
7.62
± 0.38
DIA. 1.2
10°
0.9
12.8
± 0.2
6
2.54 ± 0.38
0.53
± 0.05
4 x 2.54
6.4
± 0.1
7
± 0.1
10.4 MIN.
1
2
3
4
5
6
7
8
9
10
g
f
Common A/C
e
d
DP
c
Common A/C
b
a
1
2
3
4
5
10
9
8
7
6
DP
a
b
g
c
d
e
f
HDSP-315X pkg dimen. (A)
HDSP-XXXX
HP XYY ZW
COLOR BIN (NOTE 3)
LUMINOUS
INTENSITY
CATEGORY
DATE
CODE
PIN FUNCTION
13.0
12.25 ± 0.15
0.38 ± 0.08
2.54 ± 0.3 TYP.
DIA. 1.25
10°
1.25
17.50
7.40
2.54 ± 0.38
0.29 ± 0.08 TYP.
15.24 ± 0.3
6.40
± 0.1
7.00
± 0.1
3.60 ± 0.3
PIN FUNCTION
1
2
3
4
5
6
7
8
9
10
e
d
Common A/C
c
DP
b
a
Common A/C
f
g
HDSP-315X pkg dimen. (B)
HDSP-XXXX
HP XYY ZW
COLOR BIN (NOTE 3)
LUMINOUS
INTENSITY
CATEGORY
DATE
CODE
1.04 ± 0.3 TYP.
+ 0.3
– 0.1
1 2 3 4 5
10 9 8 7 6
5.08
DP
a
b
g
c
d
e
f
4
Absolute Maximum Ratings
AlGaAs HER
Red Low Low
Description Current HER Current Yellow Green Units
Average Power per 37 105 52 105 105 mW
Segment or DP
Peak Forward Current 45 90[2] 45 90[5] 90[7] mA
per Segment or DP
DC Forward Current 15[1] 30[3] 15[4] 30[6] 30[8] mA
per Segment or DP
Operating Temperature Range -20 to 100 -40 to +100 °C
Storage Temperature Range -40 to +100 °C
Reverse Voltage per 3.0 V
Segment or DP
Wavesoldering Temperature 250 °C
for 3 seconds 1.59 mm below body
Notes:
1. Derate above 91°C at 0.53 mA/°C.
2. See Figure 9 to establish pulsed conditions.
3. Derate above 53°C at 0.45 mA/°C.
4. Derate above 80°C at 0.38 mA/°C.
5. See Figure 10 to establish pulsed conditions.
6. Derate above 81°C at 0.52 mA/°C.
7. See Figure 11 to establish pulsed ocnditions.
8. Derate above 39°C at 0.37 mA/°C.
Electrical/Optical Characteristics at TA = 25°C
AlGaAs Red Low Current
Device Series Test
HDSP- Parameter Symbol Min. Typ. Max. Units Conditions
315/316H Luminous Intensity/Segment[1,2] IV 180 650 µcd IF = 1 mA
515/516H (Digit Average)
Forward Voltage/Segment or DP VF 1.8 2.2 V IF = 1 mA
Peak Wavelength λPEAK 645 nm
Dominant Wavelength[3] λd 637 nm
Reverse Voltage/Segment or DP[4] VR 3 15 V IR = 100 µA
Thermal Resistance LED RθJ-PIN 255 °C/W/Seg
Junction-to-Pin
HER
Device Series Test
HDSP- Parameter Symbol Min. Typ. Max. Units Conditions
315/316E Luminous Intensity/Segment[1,2] IV 450 2600 µcd IF = 10 mA
515/516E (Digit Average)
Forward Voltage/Segment or DP VF 1.9 2.5 V IF = 10 mA
Peak Wavelength λPEAK 635 nm
Dominant Wavelength[3] λd 626 nm
Reverse Voltage/Segment or DP[4] VR 3 30 V IR = 100 µA
Thermal Resistance LED RθJ-PIN 200 °C/W/Seg
Junction-to-Pin
5
HER Low Current
Device Series Test
HDSP- Parameter Symbol Min. Typ. Max. Units Conditions
315/316L Luminous Intensity/Segment[1,2] IV 180 370 µcd IF = 2 mA
515/516L (Digit Average)
Forward Voltage/Segment or DP VF 2.1 2.5 V IF = 2 mA
Peak Wavelength λPEAK 635 nm
Dominant Wavelength[3] λd 626 nm
Reverse Voltage/Segment or DP[4] VR 3 30 V IR = 100 µA
Thermal Resistance LED RθJ-PIN 200 °C/W/Seg
Junction-to-Pin
Yellow
Device Series Test
HDSP- Parameter Symbol Min. Typ. Max. Units Conditions
315/316Y Luminous Intensity/Segment[1,2] IV 450 1800 µcd IF = 10 mA
515/516Y (Digit Average)
Forward Voltage/Segment or DP VF 2.0 2.5 V IF = 10 mA
Peak Wavelength λPEAK 583 nm
Dominant Wavelength[3] λd 586 nm
Reverse Voltage/Segment or DP[4] VR 3 50 V IR = 100 µA
Thermal Resistance LED RθJ-PIN 200 °C/W/Seg
Junction-to-Pin
Green
Device Series Test
HDSP- Parameter Symbol Min. Typ. Max. Units Conditions
315/316G Luminous Intensity/Segment[1,2] IV 450 5000 µcd IF = 10 mA
515/516G (Digit Average)
Forward Voltage/Segment or DP VF 2.1 2.5 V IF = 10 mA
Peak Wavelength λPEAK 566 nm
Dominant Wavelength[3] λd 571 nm
Reverse Voltage/Segment or DP[4] VR 3 50 V IR = 100 µA
Thermal Resistance LED RθJ-PIN 200 °C/W/Seg
Junction-to-Pin
Notes:
1. Case temperature of device immediately prior to the intensity measurement is 25°C.
2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package.
3. The dominant wavelength, λ is derived from the CIE chromaticity diagram and is that single wavelength which denes the color of the device.
4. Typical specication for reference only. Do not exceed absolute maximum ratings.
6
16
0
2
4
6
8
10
12
14
20 10090807060504030
TA – AMBIENT TEMPERATURE – °C
I
F
AVE. MAX – MAXIMUM AVERAGE
FORWARD CURRENT PER SEGMENT – mA
120110
20
18 RθJ-A = 770°C/W
I
F
– FORWARD CURRENT
PER SEGMENT – mA
1.0 2.5
50.0
2.0
0.1
VF – FORWARD VOLTAGE - V
1.5 2.0
20.0
10.0
1.0
0.5
0.50
5.0
RELATICE LUMINOUS INTENSITY
(NORMALIZED TO 1AT 1ma)
0.5 20
20
2
0.1
IF – FORWARD CURRENT PER SEGMENT – mA
1 2 5 10
10
5
1
0.5
0.2
0.20.1
AlGaAs Low Current
Figure 1. Maximum allowable average or DC current vs. ambient temperature. Figure 2. Forward current vs. forward voltage.
Figure 3. Relative luminous intensity vs DC forward current.
7
RATIO OF MAXIMUM OPERATING
PEAK CURRENT TO TEMPERATURE
DERATED DC CURRENT
IFPEAK
IDC MAX
tp – PULSE DURATION – µs
10
1
100
10 1000010001001
OPERATION IN THIS
REGION REQUIRES
TEMPERATURE
DERATING OF IDC
MAXIMUM
DC OPERATION
3 KHz
10 KHZ
1 KHz
300 Hz
100 Hz
RATIO OF MAXIMUM OPERATING
PEAK CURRENT TO TEMPERATURE
DERATED DC CURRENT
IFPEAK
IDC MAX
tp – PULSE DURATION – µs
10
1
100
10 1000010001001
OPERATION IN THIS
REGION REQUIRES
TEMPERATURE
DERATING OF IDC
MAXIMUM
DC OPERATION
3 KHz
10 KHZ
1 KHz
300 Hz
100 Hz
RATIO OF MAXIMUM OPERATING
PEAK CURRENT TO TEMPERATURE
DERATED DC CURRENT
IFPEAK
IDC MAX
tp – PULSE DURATION – µs
10
1
100
10 1000010001001
OPERATION IN THIS
REGION REQUIRES
TEMPERATURE
DERATING OF IDC
MAXIMUM
DC OPERATION
3 KHz
10 KHZ
1 KHz
300 Hz
100 Hz
40
0
5
10
15
20
25
30
35
20 10090
807060504030
TA – AMBIENT TEMPERATURE – °C
IDC MAX – MAXIMUM DC CURRENT
PER SEGMENT – mA
120110
50
45
HER
YELLOW
GREEN
R¸J-A = 770°C/W
0
100
80
60
40
20
IF – FORWARD CURRENT PER SEGMENT – mA
2.0 4.03.01.0
VF – FORWARD VOLTAGE – V
0 5.0
YELLOW
GREEN
HER
RELATIVE LUMINOUS INTENSITY
(NORMALIZED TO 1 AT 5 mA FOR HER AND
YELLOW AND TO 1 AT 10 mA FOR GREEN)
15
0
10
8
6
4
2
205 3010 25
12
IF – FORWARD CURRENT PER SEGMENT – mA
0
YELLOW
GREEN
HER
HER, Yellow, and Green
Figure 4. Maximum tolerable peak current vs. pulse duration – HER. Figure 5. Maximum tolerable peak current vs. pulse duration – Yellow.
Figure 6. Allowable peak current vs. pulse duration – Green. Figure 7. Maximum allowable DC current per segment as a function of
ambient temperature.
Figure 8. Forward current vs. forward voltage characteristics. Figure 9. Relative luminous intensity vs. DC forward current.
8
16
0
2
4
6
8
10
12
14
20 10090807060504030
TA – AMBIENT TEMPERATURE – °C
120110
20
18
HER
RθJ-A = 770°C/W
IF – FORWARD CURRENT PER SEGMENT – mA
0 0.5 1.0 1.5 2.0 2.5 3.0
0
VF – FORWARD VOLTAGE - V
50
40
30
20
10
HER
RELATIVE LUMINOUS INTENSITY
(NORMALIZED TO 1 AT 2 mA FOR HER AND
TO 1 AT 4 mA FOR YELLOW AND GREEN
0 2 4 6 8 10 12 14 16
0
VF – FORWARD CURRENT PER SEGMENT – mA
16
12
10
6
2
14
8
4
HER
I
F
AVE. MAX – MAXIMUM AVERAGE
FORWARD CURRENT PER SEGMENT – mA
HER Low Current
Figure 10. Maximum allowable average or DC current vs. ambient
temperature.
Figure 11. Forward current vs. forward voltage.
Figure 12. Relative luminous intensity vs. DC forward current.
Intensity Bin Limits (mcd)
HER Low Current, AlGaAs Red Low Current
HDSP-31xL/H, HDSP-51xL/H
IV Bin Category Min. Max.
E 0.180 0.360
F 0.280 0.560
G 0.450 0.900
H 0.700 1.400
I 1.100 2.200
K 1.800 3.600
L 2.800 5.600
M 4.500 9.000
N 7.000 15.000
HER Std. Current, Green Std. Current, Yellow Std. Current
HDSP-31xE/G/Y, HDSP-51xE/G/Y
IV Bin Category Min. Max.
G 0.450 0.900
H 0.700 1.400
I 1.100 2.200
K 1.800 3.600
L 2.800 5.600
M 4.500 9.000
N 7.000 15.000
Color Categories
Dominant Wavelength (nm)
Color Bin Min. Max.
Yellow 1 581.50 585.00
3 584.00 587.50
2 586.50 590.00
4 589.00 592.50
Green 2 573.00 577.00
3 570.00 574.00
4 567.00 571.00
5 564.00 568.00
Note:
All categories are established for classication of products. Products
may not be available in all categories. Please contact your local Avago
representatives for further clarication/information.
Electrical/Optical
For more information on electrical/optical characteristics,
please see Application Note 1005.
Contrast Enhancement
For information on contrast enhancement, please see
Application Note 1015.
Soldering/Cleaning
Cleaning agents from the ketone family (acetone, methyl
ethyl ketone, etc.) and from the chlorinated hydrocarbon
family (methylene chloride, trichloro ethylene, carbon
tetrachloride, etc.) are not recommended for cleaning LED
parts. All of these various solvents attack or dissolve the
encapsulating epoxies used to form the package of plastic
LED parts.
For further information on soldering LEDs, please refer to
Application Note 1027.
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. Obsoletes 5989-2640EN
AV02-1769EN - March 28, 2011