HAC Series
• Load Voltage range 24 to 660 VAC
• Output rating up to 150 Arms
• AC or DC input control options
• Locking Input Connector
• Optional Transient Protection & installed Thermal Pad
• Zero Voltage or Instantaneous Turn-on options
AVAILABLE OPTIONS
OUTPUT SPECIFICATIONS (1)
HAC24x150
Operating Voltage (47-63Hz) [Vrms]24-280 48-660
Transient Overvoltage [Vpk] 600 1200
Minimum Load Current [Arms] 0.15 0.15
Maximum Surge Current [Apk] 1 Cycle 50/60 Hz 1670/1750 1670/1750
Maximum Off-State Leakage Current @ Rated Voltage [mA]
13950/12709 13950/12709
Maximum On-State Voltage Drop @ Rated Current [Vrms] 1.15 1.15
Thermal Resistance Juncti on to Case (Rjc) [°C/W] 0.15 0.15
0.5 0.5
Wire Size max (solid/stranded) [AWG/ IEC mm²] (3) 2/0 / 67.4 2/0 / 67.4
Output Terminal Nut Torque Range [in lb (Nm) 225-300 (25.4-33.9) 225-300 (25.4-33.9)
HAC60x150
Maximum Off-State dv/dt @ Maximum Rated Voltage [V/µSec]
Maximum Load Current [Arms](2)
Maximum I²t for fusing (10msec)/(8.33msec)[A²sec]
Minimum Power Factor (with Maximum load)
1 1
500 500
150 150
PRODUCT SELECTION
Control Voltage 150 A
3-32 VDC
90-140 VAC
150-270 VAC
HAC24D150 ,HAC60D150
HAC24B150 ,HAC60B150
HAC24A150 ,HAC60A150
Series
Operating Voltage
24: 24-280 VAC
60: 48-660 VAC
Control Voltage
A: 150-270 VAC
B: 90-140 VAC
D: 4-32 VDC
Rated Load Current
150: 150 Amps
A24 150
Thermal Pad
Blank: Not Included
H: Included
HAC
Overvoltage Protection
Blank: Not Included
P: Included (6)
P
Switching Type
Blank: Zero Voltage Turn-On
-10: Instantaneous Turn-On (5)
-10H
Required for valid part number
For options only and not required for valid part number
Description
HP Rating UL 508/IEC60957 [HP (KW)]: 240 VAC
HP Rating UL 508/IEC60947 [HP (KW)]: 480 VAC
10 (7.5)
N/A
N/A
25 (18.75)
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
INPUT SPECIFICATIONS (1)
HACxxD150
Control Voltage Range 4-32 VDC (10) 90-140 VAC
Minimum Turn-Off Voltage 4 VDC 90 VAC
Must Turn-Off Voltage 1 VDC 10 VAC
Minimum Input Current (for on-state) [mA] 9 7
Maximum Input Current [mA] 15
½ Cycle 20
GENERAL SPECIFICATIONS (1)
Dielectric Strength, Input/Output (50/60Hz) 3750 Vrms
2500 Vrms
10 pF
Weight (typical) lbs/grams 0.75/340.2
Housing Material PBT 30% GF, UL 94 V-0
SSR Mounting Torque Range [in lbs/Nm] 18-20 (2-2.2)
YES (Green)
Humidity 85% non-condensing
Detachable barrier strip
GENERAL NOTES
(1) All parameters at 25°C unless otherwise specified.
(2) Heat sinking required, see derating curves.
(3) TRM3/0 lug terminal must be used.
(4) Turn-on time for Instantaneous turn-on versions is 0.02 msec.
(5) Instantaneous turn-on version is not recommended for capacitive loads. Use zero turn-on only.
(6) Output will self-trigger (450-600Vpk for HAC24 and 900-1200Vpk for HAC60), not suitable for capacitive loads.
(7) Connector/Plug Not included. See Suggested Mating Connectors/Plugs
(8) Elective Overvoltage Protection, “P” option.
WIRING DIAGRAM
Nominal Input Impedance [Ohms]
Maximum Turn-On Time [msec] (4)
Maximum Turn-Off Time [msec]
HACxxA150 HACxxB150
Current RegulatedCurrent Regulated
½ Cycle
150-270 VAC
150 VAC
10 VAC
6
10
20
30
Current Regulated
12
30
Input Terminal (7)
LED Input Status Indicator (color)
Ambient Storage Temperature Range
Ambient Operating Temperature Range
Maximum Capacitance, Input/Output
Minimum Insulation Resistance (@ 500 V DC)
Dielectric Strength, Input/Output/Base (50/60Hz)
109 Ohm
-40 to 125 °C
-30 to 80 °C
(9) Load can be wired to either SSR output terminal 1 or 2.
(10) Increase minimum voltage by 1V for operations from -20 to -30
°C
Description
Description Parameters
Input Current vs Input Voltage
Standard Regulated “DC” Inputs
Input Current (mA)
25
20
15
10
5
0
0
5 10 15 20 25 30
DC Input Voltage
HAC60D150
4-32 VDC
INPUT
STATUS
L1
L2
LOAD SIDE
SOLID STATE CONTACTOR
AC
Load
V
(
-
/ ) (+ / )
L2 ( ) L1 ( )
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
MECHANICAL SPECIFICATIONS
SUGGESTED MATING
CONNECTORS/PLUGS (7)
FRONT WIRE ENTRY
Molex: 0395332002
Phoenix: MVSTBW 2,5/ 2 -ST-5,08
REAR WIRE ENTRY
Molex: 39533 -3002
Phoenix: MVSTBR 2,5/ 2 -ST-5,08
RIGHT ANGLE
Molex: 0395300002
Phoenix: MSTB 2,5/ 2 -ST-5,08
Tolerances: ±0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]
2.90
[73.7]
4.12 [104.6]
3.62 [92.0]
2.51 [63.7]
Standard Stud
0.375 [9.52] -24
Mounting
Hole/Slot
0.20 [5.0] DIA.
INPUT
STATUS
L1
LOAD SIDE
L2
1.70
[43.2]
Max 0.82
[20.8]
1.00
[25.4]
1.87
[47.6]
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
THERMAL DERATE INFORMATION (2)
SURGE CURRENT INFORMATION
Non repetitive peak surge current at Tj initial 40
°
C
0
200
400
800
600
1000
1200
1400
1800
1600
0.01 0.1 1 10
Surge Current (Amp)
Surge Duration (Secs)
150 A
100
125
150
75
50
25
20 30 40 50 60 70 80
0
Ambient Temperature (ºC)
Load Current (Amps)
HACxxA150
0.25ºC/W 0.36ºC/W 0.50ºC/W
100
125
150
75
50
25
20 30 40 50 60 70 80
0
Ambient Temperature (ºC)
Load Current (Amps)
HACxxB150,HACxxD150
0.25ºC/W 0.36ºC/W 0.50ºC/W
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
AGENCY APPROVALS
Designed in accordance with the requirements of IEC 62314
IEC 61000-4-2 : Electrostatic Discharge: Level 3
IEC 61000-4-4 : Electrically Fast Transients: Level 3
IEC 61000-4-5 : Electricsl Surges: Level 3
949611E
ACCESSORIES
EQUIVALENT CIRCUIT BLOCK DIAGRAM
AC
AC
AC
Trigger
Circuit
Current
Limiter
AC
AC/DC
Converter
Diagram: HAC AC control
(9)
(8)
L2
L1
+DC
-
DC
AC
Trigger
Circuit
Current
Limiter
AC
Diagram:
(8)
HAC DC control
(9)
L1
L2
Hardware Kit
Recommended Accessories
Thermal Resistance
[ºC/W]
Heat Sink
Part No.
0.5
0.36
0.25
HS053
HS033
HS023
HK1 TRM3/0
Thermal Pad
HSP-5
Lug Terminal
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Rev. 091316
Agency Approvals
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
•Disconnect all
power before
installing or
working with
this equipment.
•Verify all
connections
and replace all
covers before
turning on
power.
Failure to follow
these
instructions will
result in death
or serious injury.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
•Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
con este equipo.
•Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
el equipo.
El
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
RISQUE DE
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
•Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
•Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
Gerät Arbeiten
durchführen
•Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
Abdeckungen
ersetzen.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
Verletzungen
führen.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.
•Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa
apparecchiatura
•Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima
dell’accensione
L'omissione di
queste istruzioni
provocherà la
morte o
lesioni serie
存在电击、
爆炸或电弧
闪烁危险
•
在操作此设
备之前请先
关闭电源。
若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
Fremdkörper in das Produkt ein.
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。
材料损坏和高温外壳的危险性
• 产品的一侧面板可能很热，在其冷却前请
不要触碰。
• 遵照正确的安装说明，包括扭矩值。
• 请勿让液体及其他异物进入本产品。
ANNEX - ENVIROMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated
(Pb) (Hg) (Cd) Chromium
(Cr (VI))
biphenyls
(PBB)
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
有毒有害物质或元素件部
名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)
半导体芯片
焊接点
50
Datasheet
Panel Mount
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
