dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 16-bit Digital Signal Controllers (up to 16 KB Flash and up to 2 KB SRAM) with High-Speed PWM, ADC, and Comparators Operating Conditions Advanced Analog Features (Continued) * 3.0V to 3.6V, -40C to +150C, DC to 20 MIPS * 3.0V to 3.6V, -40C to +125C, DC to 40 MIPS * 3.0V to 3.6V, -40C to +85C, DC to 50 MIPS * Up to four High-Speed Comparators with direct connection to the PWM module: - Programmable references with 1024 voltage points Core: 16-bit dsPIC33F CPU Timers/Output Compare/Input Capture * * * * * * Three general purpose timers: - Three 16-bit and one 32-bit timer/counter * Two Output Compare (OC) modules * Two Input Capture (IC) modules * Peripheral Pin Select (PPS) to allow function remap Code-efficient (C and Assembly) architecture Two 40-bit wide accumulators Single-cycle (MAC/MPY) with dual data fetch Single-cycle mixed-sign MUL plus hardware divide 32-bit multiply support Clock Management * * * * * 2.0% internal oscillator Programmable PLLs and oscillator clock sources Fail-Safe Clock Monitor (FSCM) Independent Watchdog Timer (WDT) Fast wake-up and start-up Power Management * Low-power management modes (Sleep, Idle, Doze) * Integrated Power-on Reset and Brown-out Reset High-Speed PWM * * * * Up to four PWM pairs with independent timing Dead time for rising and falling edges 1.04 ns PWM resolution PWM support for: - DC/DC, AC/DC, Inverters, PFC, and Lighting * Programmable Fault inputs * Flexible trigger configurations for ADC conversions Advanced Analog Features * ADC module: - 10-bit resolution with up to 2 Successive Approximation Register (SAR) converters (4 Msps) and up to six Sample and Hold (S&H) circuits - Up to 12 input channels grouped into six conversion pairs plus two voltage reference monitoring inputs - Dedicated result buffer for each analog channel * Flexible and independent ADC trigger sources Communication Interfaces * UART module (12.5 Mbps) - With support for LIN 2.0 protocols and IrDA(R) * 4-wire SPI module * I2CTM module (up to 1 Mbaud) with SMBus support * PPS to allow function remap Input/Output * Sink/Source 18 mA on 8 pins, 10 mA on 10 pins, and 6 mA on 17 pins * 5V-tolerant pins * Selectable open drain and pull-ups * External interrupts on up to 30 I/O pins Qualification and Class B Support * AEC-Q100 REVG (Grade 1 -40C to +125C) * AEC-Q100 REVG (Grade 0 -40C to +150C) * Class B Safety Library, IEC 60730, VDE certified Debugger Development Support * * * * In-circuit and in-application programming Two breakpoints IEEE 1149.2-compatible (JTAG) boundary scan Trace and run-time watch Packages Type SOIC SPDIP Pin Count 18 28 28 I/O Pins 13 21 21 Contact Lead/Pitch 1.27 1.27 .100'' Dimensions 10.30x7.50x2.65 17.9x7.50x2.05 1.365x.240x.120" Note: All dimensions are in millimeters (mm) unless specified. (c) 2008-2012 Microchip Technology Inc. QFN-S 28 21 0.65 6x6x0.9 QFN 44 35 0.65 8x8x1 TQFP 44 35 0.80 10x10x1 VTLA 44 35 0.50 6x6x0.9 DS70318F-page 1 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 PRODUCT FAMILIES The device names, pin counts, memory sizes and peripheral availability of each device are listed below. The following pages show their pinout diagrams. Device Program Flash Memory (Kbytes) RAM (Bytes) Remappable Pins 16-bit Timer Input Capture Output Compare UART SPI PWM(2) dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CONTROLLER FAMILIES Pins TABLE 1: dsPIC33FJ06GS101 18 6 256 8 2 0 1 1 1 2x2(1) 0 3 0 1 1 3 6 13 SOIC dsPIC33FJ06GS102 28 6 256 16 2 0 1 1 1 2x2 0 3 0 1 1 3 6 21 SPDIP SOIC QFN-S dsPIC33FJ06GS202 28 6 1K 16 2 1 1 1 1 2x2 2 3 1 1 1 3 6 21 SPDIP SOIC QFN-S dsPIC33FJ16GS402 28 16 2K 16 3 2 2 1 1 3x2 0 3 0 1 1 4 8 21 SPDIP SOIC QFN-S dsPIC33FJ16GS404 44 16 2K 30 3 2 2 1 1 3x2 0 3 0 1 1 4 8 35 QFN TQFP VTLA dsPIC33FJ16GS502 28 16 2K 16 3 2 2 1 1 4x2(1) 4 3 1 1 2 6 8 21 SPDIP SOIC QFN-S dsPIC33FJ16GS504 44 16 2K 30 3 2 2 1 1 4x2(1) 4 3 1 1 2 6 12 35 QFN TQFP VTLA Note 1: 2: 3: Packages I/O Pins Analog-to-Digital Inputs Sample and Hold (S&H) Circuit SARs I2CTM DAC Output External Interrupts(3) ADC Analog Comparator Remappable Peripherals The PWM4H:PWM4L pins are remappable. The PWM Fault pins and PWM synchronization pins are remappable. Only two out of three interrupts are remappable. DS70318F-page 2 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams = Pins are up to 5V tolerant 18-Pin SOIC 1 2 AN1/RA1 3 AN2/RA2 4 AN3/RP0(1)/CN0/RB0 5 OSC1/CLKI/AN6/RP1(1)/CN1/RB1 6 OSC2/CLKO/AN7/RP2(1)/CN2/RB2 TCK/PGED2/INT0/RP3(1)/CN3/RB3 7 8 TMS/PGEC2/RP4(1)/CN4/RB4 9 dsPIC33FJ06GS101 MCLR AN0/RA0 18 VDD 17 VSS 16 PWM1L/RA3 15 PWM1H/RA4 14 VCAP 13 VSS PGEC1/SDA1/RP7(1)/CN7/RB7 12 11 10 dsPIC33FJ06GS102 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 dsPIC33FJ06GS202 Note AVDD AVSS PWM1L/RA3 PWM1H/RA4 PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 RP12(1)/CN12/RB12 RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 PGEC3/RP15(1)/CN15/RB15 = Pins are up to 5V tolerant 28-Pin SPDIP, SOIC MCLR AN0/CMP1A/RA0 AN1/CMP1B/RA1 AN2/CMP1C/CMP2A/RA2 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 AN4/CMP2C/RP9(1)/CN9/RB9 AN5/CMP2D/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/RP1(1)/CN1/RB1 OSC2/CLKO/RP2(1)/CN2/RB2 PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 PGEC2/EXTREF/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 TDO/RP5(1)/CN5/RB5 = Pins are up to 5V tolerant 28-Pin SOIC, SPDIP MCLR AN0/RA0 AN1/RA1 AN2/RA2 AN3/RP0(1)/CN0/RB0 AN4/RP9(1)/CN9/RB9 AN5/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/RP1(1)/CN1/RB1 (1) OSC2/CLKO/RP2 /CN2/RB2 TCK/PGED2/INT0/RP3(1)/CN3/RB3 TMS/PGEC2/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 PGED1/TDI/SCL1/RP6(1)/CN6/RB6 28 27 26 25 24 23 22 21 20 19 18 17 16 15 AVDD AVSS PWM1L/RA3 PWM1H/RA4 PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/RP12(1)/CN12/RB12 TMS/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 PGEC3/RP15(1)/CN15/RB15 The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals (c) 2008-2012 Microchip Technology Inc. DS70318F-page 3 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 28-Pin SPDIP, SOIC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 dsPIC33FJ16GS402 MCLR AN0/RA0 AN1/RA1 AN2/RA2 AN3/RP0(1)/CN0/RB0 AN4/RP9(1)/CN9/RB9 AN5/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/AN6/RP1(1)/CN1/RB1 OSC2/CLKO/AN7/RP2(1)/CN2/RB2 PGED2/INT0/RP3(1)/CN3/RB3 PGEC2/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 = Pins are up to 5V tolerant 28 27 26 25 24 23 22 21 20 19 18 17 16 15 = Pins are up to 5V tolerant 28-Pin SPDIP, SOIC Note 1: DS70318F-page 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 dsPIC33FJ16GS502 MCLR AN0/CMP1A/RA0 AN1/CMP1B/RA1 AN2/CMP1C/CMP2A/RA2 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9 AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1 OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2 PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 PGEC2/EXTREF/RP4(1)/CN4/RB4 VDD CN8/RB8/PGED3/RP8(1)/CN8/RB8 AVDD AVSS PWM1L/RA3 PWM1H/RA4 PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/PWM3L/RP12(1)/CN12/RB12 TMS/PWM3H/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 PGEC3/RP15/CN15/RB15 28 27 26 25 24 23 22 21 20 19 18 17 16 15 AVDD AVSS PWM1L/RA3 PWM1H/RA4 PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/PWM3L/RP12(1)/CN12/RB12 TMS/PWM3H/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 PGEC3/RP15(1)/CN15/RB15 The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 28-Pin QFN-S(2) 28 27 26 25 24 23 22 1 21 2 20 3 19 4 dsPIC33FJ06GS102 18 5 17 6 16 7 15 8 9 10 11 12 13 14 = Pins are up to 5V tolerant PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/RP12(1)/CN12/RB12 TMS/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 28-Pin QFN-S(2) 28 27 26 25 24 23 22 1 21 2 20 3 19 4 dsPIC33FJ06GS202 18 5 17 6 16 7 15 8 9 10 11 12 13 14 = Pins are up to 5V tolerant PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/RP12(1)/CN12/RB12 TMS/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 PGEC2/EXTREF/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 TDO/RP5(1)/CN5/RB5 PGED1/TDI/SCL/RP6(1)/CN6/RB6 AN2/CMP1C/CMP2A/RA2 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 AN4/CMP2C/RP9(1)/CN9/RB9 AN5/CMP2D/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/RP1(1)/CN1/RB1 OSC2/CLKO/RP2(1)/CN2/RB2 AN1/CMP1B/RA1 AN0/CMP1A/RA0 MCLR AVDD AVSS PWM1L/RA3 PWM1H/RA4 PGED2/INT0/RP3(1)/CN3/RB3 PGEC2/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 TDO/RP5(1)/CN5/RB5 PGED1/TDI/SCL/RP6(1)/CN6/RB6 AN2/RA2 AN3/RP0(1)/CN0/RB0 AN4/RP9(1)/CN9/RB9 AN5/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/RP1(1)/CN1/RB1 OSC2/CLKO/RP2(1)/CN2/RB2 AN1/RA1 AN0/RA0 MCLR AVDD AVSS PWM1L/RA3 PWM1H/RA4 Pin Diagrams (Continued) Note 1: The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals. 2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be connected to VSS externally. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 5 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 28-Pin QFN-S(2) 28 27 26 25 24 23 22 1 21 2 20 3 19 4 dsPIC33FJ16GS402 18 5 17 6 16 7 15 8 9 10 11 12 13 14 = Pins are up to 5V tolerant PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/PWM3L/RP12(1)/CN12/RB12 TMS/PWM3H/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 28-Pin QFN-S(2) 28 27 26 25 24 23 22 1 21 2 20 3 19 4 dsPIC33FJ16GS502 18 5 17 6 16 7 15 8 9 10 11 12 13 14 = Pins are up to 5V tolerant PWM2L/RP14(1)/CN14/RB14 PWM2H/RP13(1)/CN13/RB13 TCK/PWM3L/RP12(1)/CN12/RB12 TMS/PWM3H/RP11(1)/CN11/RB11 VCAP VSS PGEC1/SDA/RP7(1)/CN7/RB7 PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 PGEC2/EXTREF/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 TDO/RP5(1)/CN5/RB5 PGED1/TDI/SCL/RP6(1)/CN6/RB6 AN2/CMP1C/CMP2A/RA2 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9 AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1 OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2 AN1/CMP1B/RA1 AN0/CMP1A/RA0 MCLR AVDD AVSS PWM1L/RA3 PWM1H/RA4 PGED2/INT0/RP3(1)/CN3/RB3 PGEC2/RP4(1)/CN4/RB4 VDD PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 TDO/RP5(1)/CN5/RB5 PGED1/TDI/SCL/RP6(1)/CN6/RB6 AN2/RA2 AN3/RP0(1)/CN0/RB0 AN4/RP9(1)/CN9/RB9 AN5/RP10(1)/CN10/RB10 VSS OSC1/CLKIN/AN6/RP1(1)/CN1/RB1 OSC2/CLKO/AN7/RP2(1)/CN2/RB2 AN1/RA1 AN0/RA0 MCLR AVDD AVSS PWM1L/RA3 PWM1H/RA4 Pin Diagrams (Continued) Note 1: The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals. 2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be connected to VSS externally. DS70318F-page 6 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 44-Pin VTLA(2) PGED2/INT0/RP3(1)/CN3/RB3 PGEC2/RP4(1)/CN4/RB4 RP18(1)/CN18/RC2 RP23(1)/CN23/RC7 RP24(1)/CN24/RC8 VSS VDD PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 TDO/RP5(1)/CN5/RB5 PGED1/TDI/SCL/RP6(1)/CN6/RB6 = Pins are up to 5V tolerant 44 43 42 41 40 39 38 37 36 35 34 33 OSC2/CLKO/AN7/RP2(1)/CN2/RB2 1 32 OSC1/CLKI/AN6/RP1(1)/CN1/RB1 RP20(1)/CN20/RC4 2 31 RP17(1)/CN17/RC1 RP21(1)/CN21/RC5 3 30 VSS RP22(1)/CN22/RC6 4 29 VDD RP19(1)/CN19/RC3 5 28 RP26(1)/CN26/RC10 VSS 6 27 RP25(1)/CN25/RC9 VCAP 7 26 AN5/RP10(1)/CN10/RB10 TMS/PWM3H/RP11(1)/CN11/RB11 8 25 AN4/RP9(1)/CN9/RB9 TCK/PWM3L/RP12(1)/CN12/RB12 9 24 AN3/RP0(1)/CN0/RB0 PWM2H/RP13(1)/CN13/RB13 10 23 AN2/RA2 PWM2L/RP14(1)/CN14/RB14 11 12 13 14 15 16 17 18 19 20 21 22 Note AN0/RA0 RP28 /CN28/RC12 (1) RP27(1)/CN27/RC11 MCLR AVSS AVDD RP29(1)/CN29/RC13 RP16(1)/CN16/RC0 PWM1L/RA3 PWM1H/RA4 dsPIC33FJ16GS404 AN1/RA1 PGEC1/SDA/RP7(1)/CN7/RB7 1: The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals. 2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be connected to VSS externally. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 7 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 44-Pin VTLA(2) PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 PGEC2/RP4(1)/CN4/RB4 AN9/EXTREF/CMP4D/RP18(1)/CN18/RC2 RP23(1)/CN23/RC7 VSS RP24(1)/CN24/RC8 VDD PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 TDO/RP5(1)/CN5/RB5 PGED1/TDI/SCL/RP6(1)/CN6/RB6 = Pins are up to 5V tolerant 44 43 42 41 40 39 38 37 36 35 34 33 OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2 PGEC1/SDA/RP7 /CN7/RB7 1 32 OSC1/CLKI/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1 RP20(1)/CN20/RC4 2 31 AN8/CMP4C/RP17(1)/CN17/RC1 RP21(1)/CN21/RC5 3 30 VSS RP22(1)/RN22/RC6 4 29 VDD RP19(1)/CN19/RC3 5 28 AN10/RP26(1)/CN26/RC10 VSS 6 27 AN11/RP25(1)/CN25/RC9 (1) dsPIC33FJ16GS504 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 PWM2H/RP13 /CN13/RB13 10 23 AN2/CMP1C/CMP2A/RA2 PWM2L/RP14(1)/CN14/RB14 11 12 13 14 15 16 17 18 19 20 21 22 (1) PWM1H/RA4 Note AN1/CMP1B/RA1 24 AN0/CMP1A/RA0 9 (1) TCK/PWM3L/RP12 /CN12/RB12 RP28(1)/CN28/RC12 AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9 RP27(1)/CN27/RC11 25 MCLR 8 (1) AVSS TMS/PWM3H/RP11 /CN11/RB11 AVDD AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10 RP29(1)/CN29/RC13 26 RP16 /CN16/RC0 7 PWM1L/RA3 VCAP (1) 1: The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals. 2: The metal plane at the bottom of the device is not connected to any pins and is recommended to connect to VSS externally. DS70318F-page 8 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 44-Pin QFN(2) PGED2/INT0/RP3(1)/CN3/RB3 RP18(1)/CN18/RC2 PGEC2/RP4(1)/CN4/RB4 RP23(1)/CN23/RC7 VDD VSS RP24(1)/CN24/RC8 PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 = Pins are up to 5V tolerant 44 43 42 41 40 39 38 37 36 35 34 PGEC1/SDA/RP7(1)/CN7/RB7 RP20(1)/CN20/RC4 RP21(1)/CN21/RC5 RP22(1)/CN22/RC6 OSC2/CLKO/AN7/RP2(1)/CN2/RB2 OSC1/CLKI/AN6/RP1(1)/CN1/RB1 1 33 2 3 32 31 RP17(1)/CN17/RC1 RP19(1)/CN19/RC3 VSS VCAP 4 5 6 7 30 29 28 27 VSS VDD RP26(1)/CN26/RC10 RP25(1)/CN25/RC9 TMS/PWM3H/RP11(1)/CN11/RB11 TCK/PWM3L/RP12(1)/CN12/RB12 PWM2H/RP13(1)/CN13/RB13 8 9 10 26 25 24 AN5/RP10(1)/CN10/RB10 PWM2L/RP14(1)/CN14/RB14 11 23 dsPIC33FJ16GS404 AN4/RP9(1)/CN9/RB9 AN3/RP0(1)/CN0/RB0 AN2/RA2 Note AN1/RA1 MCLR RP27(1)/CN27/RC11 RP28(1)/CN28/RC12 AN0/RA0 AVSS AVDD PWM1L/RA3 RP16(1)/CN16/RC0 RP29(1)/CN29/RC13 PWM1H/RA4 12 13 14 15 16 17 18 19 20 21 22 1: The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals. 2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be connected to VSS externally. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 9 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 44-Pin QFN(2) PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 AN9/EXTREF/CMP4D/RP18(1)/CN18/RC2 PGEC2/RP4(1)/CN4/RB4 RP23(1)/CN23/RC7 VDD VSS RP24(1)/CN24/RC8 PGED3/RP8(1)/CN8/RB8 PGEC3/RP15(1)/CN15/RB15 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 = Pins are up to 5V tolerant 44 43 42 41 40 39 38 37 36 35 34 PGEC1/SDA/RP7(1)/CN7/RB7 RP20(1)/CN20/RC4 RP21(1)/CN21/RC5 RP22(1)/RN22/RC6 RP19(1)/CN19/RC3 VSS VCAP 1 2 3 4 5 6 33 32 31 30 29 28 dsPIC33FJ16GS504 TMS/PWM3H/RP11(1)/CN11/RB11 TCK/PWM3L/RP12(1)/CN12/RB12 PWM2H/RP13(1)/CN13/RB13 7 8 9 10 27 26 25 24 PWM2L/RP14(1)/CN14/RB14 11 23 OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2 OSC1/CLKI/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1 AN8/CMP4C/RP17(1)/CN17/RC1 VSS VDD AN10/RP26(1)/CN26/RC10 AN11/RP25(1)/CN25/RC9 AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10 AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 AN2/CMP1C/CMP2A/RA2 Note DS70318F-page 10 AN1/CMP1B/RA1 MCLR RP27(1)/CN27/RC11 RP28(1)/CN28/RC12 AN0/CMP1A/RA0 AVDD AVSS PWM1L/RA3 RP16(1)/CN16/RC0 RP29(1)/CN29/RC13 PWM1H/RA4 12 13 14 15 16 17 18 19 20 21 22 1: The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals. 2: The metal plane at the bottom of the device is not connected to any pins and is recommended to connect to VSS externally. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 44-Pin TQFP VDD VSS RP24(1)/CN24/RC8 RP23(1)/CN23/RC7 RP18(1)/CN18/RC2 PGEC2/RP4(1)/CN4/RB4 PGED2/INT0/RP3(1)/CN3/RB3 40 39 38 37 36 35 34 42 41 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 PGEC3/RP15(1)/CN15/RB15 PGED3/RP8(1)/CN8/RB8 43 44 VDD RP26(1)/CN26/RC10 RP25(1)/CN25/RC9 AN5/RP10(1)/CN10/RB10 AN4/RP9(1)/CN9/RB9 AN3/RP0(1)/CN0/RB0 AN2/RA2 RP28 /CN28/RC12 AN0/RA0 AN1/RA1 25 24 23 OSC2/CLKO/AN7/RP2(1)/CN2/RB2 OSC1/CLKI/AN6/RP1(1)/CN1/RB1 RP17(1)/CN17/RC1 VSS (1) MCLR RP27(1)/CN27/RC11 AVDD RP29(1)/CN29/RC13 AVSS PWM1L/RA3 22 21 20 RP16(1)/CN16/RC0 26 19 1: 33 32 31 30 29 28 27 18 17 16 15 14 Note dsPIC33FJ16GS404 13 12 RP19(1)/CN19/RC3 VSS VCAP TMS/PWM3H/RP11(1)/CN11/RB11 TCK/PWM3L/RP12(1)/CN12/RB12 PWM2H/RP13(1)/CN13/RB13 PWM2L/RP14(1)/CN14/RB14 1 2 3 4 5 6 7 8 9 10 11 PWM1H/RA4 PGEC1/SDA/RP7(1)/CN7/RB7 RP20(1)/CN20/RC4 RP21(1)/CN21/RC5 RP22(1)/CN22/RC6 = Pins are up to 5V tolerant The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals (c) 2008-2012 Microchip Technology Inc. DS70318F-page 11 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Pin Diagrams (Continued) 44-Pin TQFP VDD VSS RP24(1)/CN24/RC8 RP23(1)/CN23/RC7 AN9/EXTREF/CMP4D/RP18(1)/CN18/RC2 PGEC2/RP4(1)/CN4/RB4 PGED2/DACOUT/INT0/RP3(1)/CN3/RB3 40 39 38 37 36 35 34 42 41 43 PGED1/TDI/SCL/RP6(1)/CN6/RB6 TDO/RP5(1)/CN5/RB5 PGEC3/RP15(1)/CN15/RB15 PGED3/RP8(1)/CN8/RB8 44 VDD AN10/RP26(1)/CN26/RC10 AN11/RP25(1)/CN25/RC9 AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10 AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9 AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0 AN2/CMP1C/CMP2A/RA2 RP28 /CN28/RC12 AN0/CMP1A/RA0 AN1/CMP1B/RA1 25 24 23 OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2 OSC1/CLKI/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1 AN8/CMP4C/RP17(1)/CN17/RC1 VSS (1) MCLR RP27(1)/CN27/RC11 AVDD RP29(1)/CN29/RC13 AVSS PWM1L/RA3 22 21 20 RP16(1)/CN16/RC0 26 19 DS70318F-page 12 1: 33 32 31 30 29 28 27 18 17 16 15 14 Note dsPIC33FJ16GS504 13 12 RP19(1)/CN19/RC3 VSS VCAP TMS/PWM3H/RP11(1)/CN11/RB11 TCK/PWM3L/RP12(1)/CN12/RB12 PWM2H/RP13(1)/CN13/RB13 PWM2L/RP14(1)/CN14/RB14 1 2 3 4 5 6 7 8 9 10 11 PWM1H/RA4 PGEC1/SDA/RP7(1)/CN7/RB7 RP20(1)/CN20/RC4 RP21(1)/CN21/RC5 RP22(1)/CN22/RC6 = Pins are up to 5V tolerant The RPn pins can be used by any remappable peripheral. See the "TABLE 1: "dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Controller Families"" table for the list of available peripherals (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Table of Contents dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Product Families .......................................................................................... 2 1.0 Device Overview ........................................................................................................................................................................ 15 2.0 Guidelines for Getting Started with 16-bit Digital Signal Controllers .......................................................................................... 19 3.0 CPU............................................................................................................................................................................................ 29 4.0 Memory Organization ................................................................................................................................................................. 41 5.0 Flash Program Memory.............................................................................................................................................................. 81 6.0 Resets ....................................................................................................................................................................................... 87 7.0 Interrupt Controller ..................................................................................................................................................................... 95 8.0 Oscillator Configuration ......................................................................................................................................................... 133 9.0 Power-Saving Features............................................................................................................................................................ 145 10.0 I/O Ports ................................................................................................................................................................................... 153 11.0 Timer1 ...................................................................................................................................................................................... 181 12.0 Timer2/3 features .................................................................................................................................................................... 183 13.0 Input Capture............................................................................................................................................................................ 189 14.0 Output Compare....................................................................................................................................................................... 191 15.0 High-Speed PWM..................................................................................................................................................................... 195 16.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 217 17.0 Inter-Integrated Circuit (I2CTM) ................................................................................................................................................. 223 18.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 231 19.0 High-Speed 10-bit Analog-to-Digital Converter (ADC) ............................................................................................................. 237 20.0 High-Speed Analog Comparator .............................................................................................................................................. 261 21.0 Special Features ...................................................................................................................................................................... 265 22.0 Instruction Set Summary .......................................................................................................................................................... 273 23.0 Development Support............................................................................................................................................................... 281 24.0 Electrical Characteristics .......................................................................................................................................................... 285 25.0 High Temperature Electrical Characteristics ............................................................................................................................ 331 26.0 50 MIPS Electrical Characteristics ........................................................................................................................................... 339 27.0 DC and AC Device Characteristics Graphs.............................................................................................................................. 347 28.0 Packaging Information.............................................................................................................................................................. 351 The Microchip Web Site ..................................................................................................................................................................... 381 Customer Change Notification Service .............................................................................................................................................. 381 Customer Support .............................................................................................................................................................................. 381 Reader Response .............................................................................................................................................................................. 382 Product Identification System ............................................................................................................................................................ 383 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 13 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Referenced Sources This device data sheet is based on the following individual chapters of the "dsPIC33F/PIC24H Family Reference Manual". These documents should be considered as the primary reference for the operation of a particular module or device feature. Note: To access the documents listed below, browse to the documentation section of the dsPIC33FJ16GS504 product page of the Microchip web site (www.microchip.com). In addition to parameters, features, and other documentation, the resulting page provides links to the related family reference manual sections. * * * * * * * * * * * * * * * * * * * * * * * * Section 1. "Introduction" (DS70197) Section 2. "CPU" (DS70204) Section 3. "Data Memory" (DS70202) Section 4. "Program Memory" (DS70203) Section 5. "Flash Programming" (DS70191) Section 8. "Reset" (DS70192) Section 9. "Watchdog Timer and Power-Saving Modes" (DS70196) Section 10. "I/O Ports" (DS70193) Section 11. "Timers" (DS70205) Section 12. "Input Capture" (DS70198) Section 13. "Output Compare" (DS70209) Section 16. "Analog-to-Digital Converter (ADC)" Section 17. "UART" (DS70188) Section 18. "Serial Peripheral Interface (SPI)" (DS70206) Section 19. "Inter-Integrated CircuitTM (I2CTM)" (DS70195) Section 23. "CodeGuardTM Security (DS70199) Section 24. "Programming and Diagnostics" (DS70207) Section 25. "Device Configuration" (DS70194) Section 41. "Interrupts (Part IV)" (DS70300) Section 42. "Oscillator (Part IV)" (DS70307) Section 43. "High- Speed PWM" (DS70323) Section 44. "High-Speed 10-bit Analog-to-Digital Converter (ADC)" (DS70321) Section 45. "High-Speed Analog Comparator" (DS70296) Section 52. "Oscillator (Part VI)" (DS70644) DS70318F-page 14 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 1.0 DEVICE OVERVIEW Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the "dsPIC33F/PIC24H Family Reference Manual". Please see the Microchip web site (www.microchip.com) for the latest "dsPIC33F/PIC24H Family Reference Manual" sections. 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. This document contains device-specific information for the following dsPIC33F Digital Signal Controller (DSC) devices: * * * * * * * dsPIC33FJ06GS101 dsPIC33FJ06GS102 dsPIC33FJ06GS202 dsPIC33FJ16GS402 dsPIC33FJ16GS404 dsPIC33FJ16GS502 dsPIC33FJ16GS504 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices contain extensive Digital Signal Processor (DSP) functionality with a high-performance, 16-bit microcontroller (MCU) architecture. Figure 1-1 shows a general block diagram of the core and peripheral modules in the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices. Table 1-1 lists the functions of the various pins shown in the pinout diagrams. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 15 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 1-1: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 BLOCK DIAGRAM PSV & Table Data Access Control Block Y Data Bus X Data Bus Interrupt Controller PORTA 16 8 16 16 16 Data Latch Data Latch X RAM Y RAM Address Latch Address Latch 23 23 PCU PCH PCL Program Counter Loop Stack Control Control Logic Logic PORTB 16 23 16 16 PORTC Address Generator Units Address Latch Program Memory EA MUX Data Latch Pins ROM Latch 24 Instruction Reg Control Signals to Various Blocks Timing Generation FRC/LPRC Oscillators Literal Data 16 Instruction Decode & Control OSC2/CLKO OSC1/CLKI Voltage Regulator VCAP 16 16 DSP Engine Power-up Timer Divide Support 16 x 16 W Register Array 16 Oscillator Start-up Timer Power-on Reset 16-bit ALU Watchdog Timer 16 Brown-out Reset VDD, VSS MCLR Timers 1-3 Analog Comparators 1-4 Note: Remappable UART1 ADC1 OC1 OC2 PWM IC1,2 CNx I2C1 SPI1 4x2 Not all pins or features are implemented on all device pinout configurations. See pinout diagrams for the specific pins and features present on each device. DS70318F-page 16 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 1-1: Pin Name PINOUT I/O DESCRIPTIONS Pin Type Buffer Type PPS Capable Description AN0-AN11 I Analog No Analog input channels CLKI I ST/CMOS No CLKO O -- No External clock source input. Always associated with OSC1 pin function. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. Optionally functions as CLKO in RC and EC modes. Always associated with OSC2 pin function. OSC1 I ST/CMOS No OSC2 I/O -- No CN0-CN29 I ST No Change notification inputs. Can be software programmed for internal weak pull-ups on all inputs. IC1-IC2 I ST Yes Capture inputs 1/2 OCFA OC1-OC2 I O ST -- Yes Yes Compare Fault A input (for Compare Channels 1 and 2) Compare Outputs 1 through 2 INT0 INT1 INT2 I I I ST ST ST No Yes Yes External Interrupt 0 External Interrupt 1 External Interrupt 2 RA0-RA4 I/O ST No PORTA is a bidirectional I/O port RB0-RB15 I/O ST No PORTB is a bidirectional I/O port RC0-RC13 I/O ST No PORTC is a bidirectional I/O port RP0-RP29 Oscillator crystal input. ST buffer when configured in RC mode; CMOS otherwise. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. Optionally functions as CLKO in RC and EC modes. I/O ST No Remappable I/O pins T1CK T2CK T3CK I I I ST ST ST Yes Yes Yes Timer1 external clock input Timer2 external clock input Timer3 external clock input U1CTS U1RTS U1RX U1TX I O I O ST -- ST -- Yes Yes Yes Yes UART1 clear to send UART1 ready to send UART1 receive UART1 transmit SCK1 SDI1 SDO1 SS1 I/O I O I/O ST ST -- ST Yes Yes Yes Yes Synchronous serial clock input/output for SPI1 SPI1 data in SPI1 data out SPI1 slave synchronization or frame pulse I/O SCL1 SDA1 I/O I/O ST ST No No Synchronous serial clock input/output for I2C1 Synchronous serial data input/output for I2C1 TMS TCK TDI TDO I I I O TTL TTL TTL -- No No No No JTAG Test mode select pin JTAG test clock input pin JTAG test data input pin JTAG test data output pin Legend: CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels TTL = Transistor-Transistor Logic (c) 2008-2012 Microchip Technology Inc. Analog = Analog input P = Power PPS = Peripheral Pin Select I = Input O = Output DS70318F-page 17 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 1-1: PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Type Buffer Type PPS Capable CMP1A CMP1B CMP1C CMP1D CMP2A CMP2B CMP2C CMP2D CMP3A CMP3B CMP3C CMP3D CMP4A CMP4B CMP4C CMP4D I I I I I I I I I I I I I I I I Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog No No No No No No No No No No No No No No No No DACOUT O -- No DAC output voltage ACMP1-ACMP4 O -- Yes DAC trigger to PWM module EXTREF I Analog No External voltage reference input for the reference DACs REFCLKO O -- Yes REFCLKO output signal is a postscaled derivative of the system clock FLT1-FLT8 SYNCI1-SYNCI2 SYNCO1 PWM1L PWM1H PWM2L PWM2H PWM3L PWM3H PWM4L PWM4H I I O O O O O O O O O ST ST -- -- -- -- -- -- -- -- -- Yes Yes Yes No No No No No No Yes Yes Fault Inputs to PWM module External synchronization signal to PWM Master Time Base PWM master time base for external device synchronization PWM1 low output PWM1 high output PWM2 low output PWM2 high output PWM3 low output PWM3 high output PWM4 low output PWM4 high output PGED1 PGEC1 I/O I ST ST No No PGED2 PGEC2 I/O I ST ST No No PGED3 PGEC3 I/O I ST ST No No Data I/O pin for programming/debugging communication Channel 1 Clock input pin for programming/debugging communication Channel 1 Data I/O pin for programming/debugging communication Channel 2 Clock input pin for programming/debugging communication Channel 2 Data I/O pin for programming/debugging communication Channel 3 Clock input pin for programming/debugging communication Channel 3 MCLR I/P ST No Master Clear (Reset) input. This pin is an active-low Reset to the device. AVDD P P No Positive supply for analog modules. This pin must be connected at all times. AVDD is connected to VDD. AVSS P P No Ground reference for analog modules. AVSS is connected to VSS. VDD P -- No Positive supply for peripheral logic and I/O pins. VCAP P -- No CPU logic filter capacitor connection. VSS P -- No Ground reference for logic and I/O pins. Pin Name Description Comparator 1 Channel A Comparator 1 Channel B Comparator 1 Channel C Comparator 1 Channel D Comparator 2 Channel A Comparator 2 Channel B Comparator 2 Channel C Comparator 2 Channel D Comparator 3 Channel A Comparator 3 Channel B Comparator 3 Channel C Comparator 3 Channel D Comparator 4 Channel A Comparator 4 Channel B Comparator 4 Channel C Comparator 4 Channel D Legend: CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels TTL = Transistor-Transistor Logic DS70318F-page 18 Analog = Analog input P = Power PPS = Peripheral Pin Select I = Input O = Output (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 2.0 GUIDELINES FOR GETTING STARTED WITH 16-BIT DIGITAL SIGNAL CONTROLLERS Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the dsPIC33F/PIC24H Family Reference Manual, which is available from the Microchip website (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. 2.1 Basic Connection Requirements Getting started with the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 family of 16-bit Digital Signal Controllers (DSC) requires attention to a minimal set of device pin connections before proceeding with development. The following is a list of pin names, which must always be connected: * All VDD and VSS pins (see Section 2.2 "Decoupling Capacitors") * All AVDD and AVSS pins (regardless if ADC module is not used) (see Section 2.2 "Decoupling Capacitors") * VCAP (see Section 2.3 "Capacitor on Internal Voltage Regulator (VCAP)") * MCLR pin (see Section 2.4 "Master Clear (MCLR) Pin") * PGECx/PGEDx pins used for In-Circuit Serial ProgrammingTM (ICSPTM) and debugging purposes (see Section 2.5 "ICSPTM Pins") * OSC1 and OSC2 pins when external oscillator source is used (see Section 2.6 "External Oscillator Pins") (c) 2008-2012 Microchip Technology Inc. 2.2 Decoupling Capacitors The use of decoupling capacitors on every pair of power supply pins, such as VDD, VSS, AVDD and AVSS is required. Consider the following criteria when using decoupling capacitors: * Value and type of capacitor: Recommendation of 0.1 F (100 nF), 10-20V. This capacitor should be a low-ESR and have resonance frequency in the range of 20 MHz and higher. It is recommended that ceramic capacitors be used. * Placement on the printed circuit board: The decoupling capacitors should be placed as close to the pins as possible. It is recommended to place the capacitors on the same side of the board as the device. If space is constricted, the capacitor can be placed on another layer on the PCB using a via; however, ensure that the trace length from the pin to the capacitor is within one-quarter inch (6 mm) in length. * Handling high frequency noise: If the board is experiencing high frequency noise, upward of tens of MHz, add a second ceramic-type capacitor in parallel to the above described decoupling capacitor. The value of the second capacitor can be in the range of 0.01 F to 0.001 F. Place this second capacitor next to the primary decoupling capacitor. In high-speed circuit designs, consider implementing a decade pair of capacitances as close to the power and ground pins as possible. For example, 0.1 F in parallel with 0.001 F. * Maximizing performance: On the board layout from the power supply circuit, run the power and return traces to the decoupling capacitors first, and then to the device pins. This ensures that the decoupling capacitors are first in the power chain. Equally important is to keep the trace length between the capacitor and the power pins to a minimum thereby reducing PCB track inductance. DS70318F-page 19 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 2-1: RECOMMENDED MINIMUM CONNECTION 0.1 F Ceramic 10 F Tantalum R R1 VSS VDD 2.4 VCAP VDD dsPIC33F VSS VDD VSS VDD AVSS VDD AVDD VSS 0.1 F Ceramic 0.1 F Ceramic 0.1 F Ceramic L1(1) 1: As an option, instead of a hard-wired connection, an inductor (L1) can be substituted between VDD and AVDD to improve ADC noise rejection. The inductor impedance should be less than 1 and the inductor capacity greater than 10 mA. Where: F CNV f = -------------2 1 f = ----------------------( 2 LC ) (i.e., ADC conversion rate/2) 1 L = ---------------------- ( 2f C ) pin provides two specific device * Device Reset * Device programming and debugging. C Note Master Clear (MCLR) Pin The MCLR functions: MCLR 0.1 F Ceramic The placement of this capacitor should be close to the VCAP. It is recommended that the trace length not exceed one-quarter inch (6 mm). Refer to Section 21.2 "On-Chip Voltage Regulator" for details. During device programming and debugging, the resistance and capacitance that can be added to the pin must be considered. Device programmers and debuggers drive the MCLR pin. Consequently, specific voltage levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values of R and C will need to be adjusted based on the application and PCB requirements. For example, as shown in Figure 2-2, it is recommended that the capacitor C, be isolated from the MCLR pin during programming and debugging operations. Place the components shown in Figure 2-2 within one-quarter inch (6 mm) from the MCLR pin. FIGURE 2-2: EXAMPLE OF MCLR PIN CONNECTIONS VDD 2 R R1 MCLR 2.2.1 TANK CAPACITORS On boards with power traces running longer than six inches in length, it is suggested to use a tank capacitor for integrated circuits including DSCs to supply a local power source. The value of the tank capacitor should be determined based on the trace resistance that connects the power supply source to the device, and the maximum current drawn by the device in the application. In other words, select the tank capacitor so that it meets the acceptable voltage sag at the device. Typical values range from 4.7 F to 47 F. 2.3 Capacitor on Internal Voltage Regulator (VCAP) JP dsPIC33F C Note 1: R 10 k is recommended. A suggested starting value is 10 k. Ensure that the MCLR pin VIH and VIL specifications are met. 2: R1 470 will limit any current flowing into MCLR from the external capacitor C, in the event of MCLR pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Ensure that the MCLR pin VIH and VIL specifications are met. A low-ESR (< 5 Ohms) capacitor is required on the VCAP pin, which is used to stabilize the voltage regulator output voltage. The VCAP pin must not be connected to VDD, and must have a capacitor between 4.7 F and 10 F, 16V connected to ground. The type can be ceramic or tantalum. Refer to Section 24.0 "Electrical Characteristics" for additional information. DS70318F-page 20 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 2.5 ICSPTM Pins FIGURE 2-3: The PGECx and PGEDx pins are used for In-Circuit Serial ProgrammingTM (ICSPTM) and debugging purposes. It is recommended to keep the trace length between the ICSP connector and the ICSP pins on the device as short as possible. If the ICSP connector is expected to experience an ESD event, a series resistor is recommended, with the value in the range of a few tens of Ohms, not to exceed 100 Ohms. Pull-up resistors, series diodes, and capacitors on the PGECx and PGEDx pins are not recommended as they will interfere with the programmer/debugger communications to the device. If such discrete components are an application requirement, they should be removed from the circuit during programming and debugging. Alternatively, refer to the AC/DC characteristics and timing requirements information in the respective device Flash programming specification for information on capacitive loading limits and pin input voltage high (VIH) and input low (VIL) requirements. Ensure that the "Communication Channel Select" (i.e., PGECx/PGEDx pins) programmed into the device matches the physical connections for the ICSP to MPLAB(R) ICD 3 or MPLAB(R) REAL ICETM. For more information on ICD 3 and REAL ICE connection requirements, refer to the following documents that are available on the Microchip website. * "Using MPLAB(R) ICD 3" (poster) DS51765 * "MPLAB(R) ICD 3 Design Advisory" DS51764 * "MPLAB(R) REAL ICETM In-Circuit Debugger User's Guide" DS51616 * "Using MPLAB(R) REAL ICETM" (poster) DS51749 2.6 External Oscillator Pins SUGGESTED PLACEMENT OF THE OSCILLATOR CIRCUIT Main Oscillator 13 Guard Ring 14 15 Guard Trace Secondary Oscillator 16 17 18 19 20 2.7 Oscillator Value Conditions on Device Start-up If the PLL of the target device is enabled and configured for the device start-up oscillator, the maximum oscillator source frequency must be limited to 4 MHz < FIN < 8 MHz to comply with device PLL start-up conditions. This means that if the external oscillator frequency is outside this range, the application must start up in the FRC mode first. The default PLL settings after a POR with an oscillator frequency outside this range will violate the device operating speed. Once the device powers up, the application firmware can initialize the PLL SFRs, CLKDIV, and PLLDBF to a suitable value, and then perform a clock switch to the Oscillator + PLL clock source. Note that clock switching must be enabled in the device Configuration word. Many DSCs have options for at least two oscillators: a high-frequency primary oscillator and a low-frequency secondary oscillator (refer to Section 8.0 "Oscillator Configuration" for details). The oscillator circuit should be placed on the same side of the board as the device. Also, place the oscillator circuit close to the respective oscillator pins, not exceeding one-half inch (12 mm) distance between them. The load capacitors should be placed next to the oscillator itself, on the same side of the board. Use a grounded copper pour around the oscillator circuit to isolate them from surrounding circuits. The grounded copper pour should be routed directly to the MCU ground. Do not run any signal traces or power traces inside the ground pour. Also, if using a two-sided board, avoid any traces on the other side of the board where the crystal is placed. A suggested layout is shown in Figure 2-3. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 21 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 2.8 Configuration of Analog and Digital Pins During ICSP Operations If MPLAB ICD 2, ICD 3 or REAL ICE is selected as a debugger, it automatically initializes all of the A/D input pins (ANx) as "digital" pins, by setting all bits in the ADPCFG register. The bits in the registers that correspond to the A/D pins that are initialized by MPLAB ICD 2, ICD 3, or REAL ICE, must not be cleared by the user application firmware; otherwise, communication errors will result between the debugger and the device. If your application needs to use certain A/D pins as analog input pins during the debug session, the user application must clear the corresponding bits in the ADPCFG register during initialization of the ADC module. When MPLAB ICD 2, ICD 3, or REAL ICE is used as a programmer, the user application firmware must correctly configure the ADPCFG register. Automatic initialization of these registers is only done during debugger operation. Failure to correctly configure the register(s) will result in all A/D pins being recognized as analog input pins, resulting in the port value being read as a logic '0', which may affect user application functionality. 2.9 Unused I/Os Unused I/O pins should be configured as outputs and driven to a logic-low state. Alternatively, connect a 1k to 10k resistor between VSS and unused pins and drive the output to logic low. 2.10 Typical Application Connection Examples Examples of typical application connections are shown in Figure 2-4 through Figure 2-11. DS70318F-page 22 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 2-4: DIGITAL PFC IPFC VHV_BUS |VAC| k1 k3 VAC k2 ADC Channel FET Driver ADC Channel PWM Output ADC Channel dsPIC33FJ06GS101 FIGURE 2-5: BOOST CONVERTER IMPLEMENTATION IPFC VINPUT VOUTPUT k1 k3 ADC Channel k2 FET Driver ADC Channel PWM Output ADC Channel dsPIC33FJ06GS101 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 23 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 2-6: SINGLE-PHASE SYNCHRONOUS BUCK CONVERTER 12V Input 5V Output I5V FET Driver k1 PWM PWM k7 ADC Channel Analog Comp. k2 ADC Channel dsPIC33FJ06GS202 FIGURE 2-7: MULTI-PHASE SYNCHRONOUS BUCK CONVERTER 3.3V Output 12V Input k6 dsPIC33FJ06GS502 PWM FET Driver PWM ADC Channel FET Driver PWM PWM k7 PWM PWM FET Driver Analog Comparator k3 Analog Comparator k4 Analog Comparator k5 ADC Channel DS70318F-page 24 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 2-8: OFF-LINE UPS VDC Push-Pull Converter Full-Bridge Inverter VOUT+ VBAT + VOUTGND GND FET Driver FET Driver PWM PWM k2 k1 ADC ADC or Analog Comp. k3 FET Driver FET Driver FET Driver FET Driver PWM PWM PWM PWM dsPIC33FJ16GS504 ADC k4 k5 ADC ADC ADC PWM FET Driver k6 + Battery Charger (c) 2008-2012 Microchip Technology Inc. DS70318F-page 25 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 2-9: INTERLEAVED PFC VOUT+ |VAC| k4 VAC k3 k1 k2 VOUTFET Driver ADC Channel ADC Channel DS70318F-page 26 PWM FET Driver ADC Channel PWM ADC Channel ADC Channel dsPIC33FJ06GS202 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 2-10: PHASE-SHIFTED FULL-BRIDGE CONVERTER VIN+ Gate 6 Gate 3 Gate 1 VOUT+ S1 S3 VOUT- Gate 2 Gate 4 Gate 5 Gate 6 Gate 5 VIN- FET Driver k2 PWM ADC Channel k1 Analog Ground Gate 1 S1 FET Driver PWM Gate 3 S3 FET Driver ADC Channel dsPIC33FJ06GS202 PWM Gate 2 Gate 4 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 27 AC-TO-DC POWER SUPPLY WITH PFC AND THREE OUTPUTS (12V, 5V, AND 3.3V) ZVT with Current Doubler Synchronous Rectifier VHV_BUS Isolation Barrier VOUT IZVT 3.3V Multi-Phase Buck Stage 3.3V Output 12V Input I3.3V_1 FET Driver FET Driver k4 FET Driver 5V Output 5V Buck Stage I3.3V_2 ADC ADC Channel Channel FET Driver ADC Ch. ADC Ch. PWM Output PWM ADC Ch. k5 FET Driver k6 k7 ADC Channel Analog Comp. ADC Channel UART RX Secondary Controller dsPIC33FJ16GS504 PFC Stage k2 UART TX FET Driver FET Driver I3.3V_3 PWM PWM Primary Controller dsPIC33FJ16GS504 PWM PWM PWM PWM PWM PWM PWM PWM PWM I5V PWM PWM Analog Comparator k8 Analog Comparator k9 Analog Comparator k10 ADC Channel (c) 2008-2012 Microchip Technology Inc. VAC k3 k1 |VAC| VHV_BUS IPFC FET Driver k11 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 28 FIGURE 2-11: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 3.0 CPU Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 2. "CPU" (DS70204) in the "dsPIC33F/PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The CPU module has a 16-bit (data) modified Harvard architecture with an enhanced instruction set, including significant support for DSP. The CPU has a 24-bit instruction word with a variable length opcode field. The Program Counter (PC) is 23 bits wide and addresses up to 4M x 24 bits of user program memory space. The actual amount of program memory implemented varies from device to device. A singlecycle instruction prefetch mechanism is used to help maintain throughput and provides predictable execution. All instructions execute in a single cycle, with the exception of instructions that change the program flow, the double-word move (MOV.D) instruction and the table instructions. Overhead-free program loop constructs are supported using the DO and REPEAT instructions, both of which are interruptible at any point. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices have sixteen, 16-bit working registers in the programmer's model. Each of the working registers can serve as a data, address or address offset register. The sixteenth working register (W15) operates as a software Stack Pointer (SP) for interrupts and calls. There are two classes of instruction in the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices: MCU and DSP. These two instruction classes are seamlessly integrated into a single CPU. The instruction set includes many addressing modes and is designed for optimum C compiler efficiency. For most instructions, the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 is capable of executing a data (or program data) memory read, a working register (data) read, a data memory write and a program (instruction) memory read per instruction cycle. As a result, three parameter instructions can be supported, allowing A + B = C operations to be executed in a single cycle. (c) 2008-2012 Microchip Technology Inc. A block diagram of the CPU is shown in Figure 3-1, and the programmer's model is shown in Figure 3-2. 3.1 Data Addressing Overview The data space can be addressed as 32K words or 64 Kbytes and is split into two blocks, referred to as X and Y data memory. Each memory block has its own independent Address Generation Unit (AGU). The MCU class of instructions operates solely through the X memory AGU, which accesses the entire memory map as one linear data space. Certain DSP instructions operate through the X and Y AGUs to support dual operand reads, which splits the data address space into two parts. The X and Y data space boundary is device-specific. Overhead-free circular buffers (Modulo Addressing mode) are supported in both X and Y address spaces. The Modulo Addressing removes the software boundary checking overhead for DSP algorithms. Furthermore, the X AGU circular addressing can be used with any of the MCU class of instructions. The X AGU also supports Bit-Reversed Addressing to greatly simplify input or output data reordering for radix-2 FFT algorithms. The upper 32 Kbytes of the data space memory map can optionally be mapped into program space at any 16K program word boundary defined by the 8-bit Program Space Visibility Page (PSVPAG) register. The program-to-data space mapping feature allows any instruction access program space as if it were data space. 3.2 DSP Engine Overview The DSP engine features a high-speed, 17-bit by 17-bit multiplier, a 40-bit ALU, two 40-bit saturating accumulators and a 40-bit bidirectional barrel shifter. The barrel shifter is capable of shifting a 40-bit value up to 16 bits, right or left, in a single cycle. The DSP instructions operate seamlessly with all other instructions and have been designed for optimal realtime performance. The MAC instruction and other associated instructions can concurrently fetch two data operands from memory while multiplying two W registers and accumulating and optionally saturating the result in the same cycle. This instruction functionality requires that the RAM data space be split for these instructions and linear for all others. Data space partitioning is achieved in a transparent and flexible manner through dedicating certain working registers to each address space. DS70318F-page 29 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 3.3 Special MCU Features The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices support 16/16 and 32/16 divide operations, both fractional and integer. All divide instructions are iterative operations. They must be executed within a REPEAT loop, resulting in a total execution time of 19 instruction cycles. The divide operation can be interrupted during any of those 19 cycles without loss of data. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices feature a 17-bit by 17-bit single-cycle multiplier that is shared by both the MCU ALU and DSP engine. The multiplier can perform signed, unsigned and mixed sign multiplication. Using a 17-bit by 17-bit multiplier for 16-bit by 16-bit multiplication not only allows you to perform mixed sign multiplication, it also achieves accurate results for special operations, such as (-1.0) x (1.0). FIGURE 3-1: A 40-bit barrel shifter is used to perform up to a 16-bit left or right shift in a single cycle. The barrel shifter can be used by both MCU and DSP instructions. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CPU CORE BLOCK DIAGRAM PSV & Table Data Access Control Block Y Data Bus X Data Bus Interrupt Controller 8 16 16 16 16 Data Latch Data Latch X RAM Y RAM Address Latch Address Latch 23 23 PCU PCH PCL Program Counter Loop Stack Control Control Logic Logic 16 23 16 16 Address Generator Units Address Latch Program Memory EA MUX Data Latch ROM Latch 24 Instruction Reg 16 Literal Data Instruction Decode & Control 16 16 Control Signals to Various Blocks DSP Engine Divide Support 16 x 16 W Register Array 16 16-bit ALU 16 To Peripheral Modules DS70318F-page 30 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 3-2: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 PROGRAMMER'S MODEL D15 D0 W0/WREG PUSH.S Shadow W1 DO Shadow W2 W3 Legend W4 DSP Operand Registers W5 W6 W7 Working Registers W8 W9 DSP Address Registers W10 W11 W12/DSP Offset W13/DSP Write Back W14/Frame Pointer W15/Stack Pointer Stack Pointer Limit Register SPLIM AD39 AD15 AD31 AD0 ACCA DSP Accumulators ACCB PC22 PC0 Program Counter 0 0 7 TBLPAG Data Table Page Address 7 0 PSVPAG Program Space Visibility Page Address 15 0 RCOUNT REPEAT Loop Counter 15 0 DCOUNT DO Loop Counter 22 0 DOSTART DO Loop Start Address DOEND DO Loop End Address 22 15 0 Core Configuration Register CORCON OA OB SA SB OAB SAB DA SRH (c) 2008-2012 Microchip Technology Inc. DC IPL2 IPL1 IPL0 RA N OV Z C STATUS Register SRL DS70318F-page 31 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 3.4 CPU Control Registers REGISTER 3-1: R-0 OA SR: CPU STATUS REGISTER R-0 R/C-0 R/C-0 OB SA(1) (1) SB R-0 OAB R/C-0 (1,4) SAB R -0 R/W-0 DA DC bit 15 bit 8 R/W-0(2) R/W-0(3) R/W-0(3) (2) IPL<2:0> R-0 R/W-0 R/W-0 R/W-0 R/W-0 RA N OV Z C bit 7 bit 0 Legend: C = Clearable bit R = Readable bit U = Unimplemented bit, read as `0' S = Settable bit W = Writable bit -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 OA: Accumulator A Overflow Status bit 1 = Accumulator A overflowed 0 = Accumulator A has not overflowed bit 14 OB: Accumulator B Overflow Status bit 1 = Accumulator B overflowed 0 = Accumulator B has not overflowed bit 13 SA: Accumulator A Saturation `Sticky' Status bit(1) 1 = Accumulator A is saturated or has been saturated at some time 0 = Accumulator A is not saturated bit 12 SB: Accumulator B Saturation `Sticky' Status bit(1) 1 = Accumulator B is saturated or has been saturated at some time 0 = Accumulator B is not saturated bit 11 OAB: OA || OB Combined Accumulator Overflow Status bit 1 = Accumulators A or B have overflowed 0 = Neither Accumulators A or B have overflowed bit 10 SAB: SA || SB Combined Accumulator `Sticky' Status bit(1,4) 1 = Accumulators A or B are saturated or have been saturated at some time in the past 0 = Neither Accumulator A or B are saturated bit 9 DA: DO Loop Active bit 1 = DO loop in progress 0 = DO loop not in progress bit 8 DC: MCU ALU Half Carry/Borrow bit 1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred 0 = No carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred Note 1: 2: 3: 4: This bit can be read or cleared (not set). The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority Level (IPL). The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when IPL<3> = 1. The IPL<2:0> Status bits are read-only when NSTDIS = 1 (INTCON1<15>). Clearing this bit will clear SA and SB. DS70318F-page 32 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 3-1: SR: CPU STATUS REGISTER (CONTINUED) bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2) 111 = CPU Interrupt Priority Level is 7 (15), user interrupts disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 4 RA: REPEAT Loop Active bit 1 = REPEAT loop in progress 0 = REPEAT loop not in progress bit 3 N: MCU ALU Negative bit 1 = Result was negative 0 = Result was non-negative (zero or positive) bit 2 OV: MCU ALU Overflow bit This bit is used for signed arithmetic (2's complement). It indicates an overflow of a magnitude that causes the sign bit to change state. 1 = Overflow occurred for signed arithmetic (in this arithmetic operation) 0 = No overflow occurred bit 1 Z: MCU ALU Zero bit 1 = An operation that affects the Z bit has set it at some time in the past 0 = The most recent operation that affects the Z bit has cleared it (i.e., a non-zero result) bit 0 C: MCU ALU Carry/Borrow bit 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: 2: 3: 4: This bit can be read or cleared (not set). The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority Level (IPL). The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when IPL<3> = 1. The IPL<2:0> Status bits are read-only when NSTDIS = 1 (INTCON1<15>). Clearing this bit will clear SA and SB. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 33 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 3-2: U-0 -- bit 15 U-0 -- R/W-0 SATB Legend: R = Readable bit 0' = Bit is cleared bit 11 bit 10-8 U-0 -- R/W-0 US R/W-0 EDT(1) R-0 R-0 DL<2:0> R-0 bit 8 R/W-0 SATA bit 7 bit 15-13 bit 12 CORCON: CORE CONTROL REGISTER R/W-1 SATDW R/W-0 ACCSAT C = Clearable bit W = Writable bit `x = Bit is unknown R/C-0 IPL3(2) R/W-0 PSV R/W-0 RND R/W-0 IF bit 0 -n = Value at POR `1' = Bit is set U = Unimplemented bit, read as `0' Unimplemented: Read as `0' US: DSP Multiply Unsigned/Signed Control bit 1 = DSP engine multiplies are unsigned 0 = DSP engine multiplies are signed EDT: Early DO Loop Termination Control bit(1) 1 = Terminate executing DO loop at end of current loop iteration 0 = No effect DL<2:0>: DO Loop Nesting Level Status bits 111 = 7 DO loops active * * * bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Note 1: 2: 001 = 1 DO loop active 000 = 0 DO loops active SATA: ACCA Saturation Enable bit 1 = Accumulator A saturation enabled 0 = Accumulator A saturation disabled SATB: ACCB Saturation Enable bit 1 = Accumulator B saturation enabled 0 = Accumulator B saturation disabled SATDW: Data Space Write from DSP Engine Saturation Enable bit 1 = Data space write saturation enabled 0 = Data space write saturation disabled ACCSAT: Accumulator Saturation Mode Select bit 1 = 9.31 saturation (super saturation) 0 = 1.31 saturation (normal saturation) IPL3: CPU Interrupt Priority Level Status bit 3(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less PSV: Program Space Visibility in Data Space Enable bit 1 = Program space visible in data space 0 = Program space not visible in data space RND: Rounding Mode Select bit 1 = Biased (conventional) rounding enabled 0 = Unbiased (convergent) rounding enabled IF: Integer or Fractional Multiplier Mode Select bit 1 = Integer mode enabled for DSP multiply ops 0 = Fractional mode enabled for DSP multiply ops This bit will always read as `0'. The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level. DS70318F-page 34 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 3.5 Arithmetic Logic Unit (ALU) 3.6 DSP Engine The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 ALU is 16 bits wide and is capable of addition, subtraction, bit shifts and logic operations. Unless otherwise mentioned, arithmetic operations are 2's complement in nature. Depending on the operation, the ALU can affect the values of the Carry (C), Zero (Z), Negative (N), Overflow (OV) and Digit Carry (DC) Status bits in the SR register. The C and DC Status bits operate as Borrow and Digit Borrow bits, respectively, for subtraction operations. The DSP engine consists of a high-speed, 17-bit x 17-bit multiplier, a barrel shifter and a 40-bit adder/ subtracter (with two target accumulators, round and saturation logic). The ALU can perform 8-bit or 16-bit operations, depending on the mode of the instruction that is used. Data for the ALU operation can come from the W register array or data memory, depending on the addressing mode of the instruction. Likewise, output data from the ALU can be written to the W register array or a data memory location. The DSP engine can also perform inherent accumulator-to-accumulator operations that require no additional data. These instructions are ADD, SUB and NEG. Refer to the "16-bit MCU and DSC Programmer's Reference Manual" (DS70157) for information on the SR bits affected by each instruction. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 CPU incorporates hardware support for both multiplication and division. This includes a dedicated hardware multiplier and support hardware for 16-bit-divisor division. 3.5.1 MULTIPLIER Using the high-speed, 17-bit x 17-bit multiplier of the DSP engine, the ALU supports unsigned, signed or mixed sign operation in several MCU multiplication modes: * * * * * * * 16-bit x 16-bit signed 16-bit x 16-bit unsigned 16-bit signed x 5-bit (literal) unsigned 16-bit unsigned x 16-bit unsigned 16-bit unsigned x 5-bit (literal) unsigned 16-bit unsigned x 16-bit signed 8-bit unsigned x 8-bit unsigned 3.5.2 DIVIDER The divide block supports 32-bit/16-bit and 16-bit/16-bit signed and unsigned integer divide operations with the following data sizes: * * * * 32-bit signed/16-bit signed divide 32-bit unsigned/16-bit unsigned divide 16-bit signed/16-bit signed divide 16-bit unsigned/16-bit unsigned divide The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 is a single-cycle instruction flow architecture; therefore, concurrent operation of the DSP engine with MCU instruction flow is not possible. However, some MCU ALU and DSP engine resources can be used concurrently by the same instruction (for example, ED, EDAC). The DSP engine has options selected through bits in the CPU Core Control register (CORCON), as listed below: * * * * * * Fractional or integer DSP multiply (IF) Signed or unsigned DSP multiply (US) Conventional or convergent rounding (RND) Automatic saturation on/off for ACCA (SATA) Automatic saturation on/off for ACCB (SATB) Automatic saturation on/off for writes to data memory (SATDW) * Accumulator Saturation mode selection (ACCSAT) A block diagram of the DSP engine is shown in Figure 3-3. TABLE 3-1: Instruction DSP INSTRUCTIONS SUMMARY Algebraic Operation CLR A=0 ED EDAC MAC MAC MOVSAC MPY MPY MPY.N MSC A = (x - y)2 A = A + (x - y)2 A = A + (x * y) A = A + x2 No change in A A=x*y A=x2 A=-x*y A=A-x*y ACC Write Back Yes No No Yes No Yes No No No Yes The quotient for all divide instructions ends up in W0 and the remainder in W1. 16-bit signed and unsigned DIV instructions can specify any W register for both the 16-bit divisor (Wn) and any W register (aligned) pair (W(m + 1):Wm) for the 32-bit dividend. The divide algorithm takes one cycle per bit of divisor, so both 32-bit/ 16-bit and 16-bit/16-bit instructions take the same number of cycles to execute. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 35 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 3-3: DSP ENGINE BLOCK DIAGRAM 40 S a 40 Round t 16 u Logic r a t e 40-bit Accumulator A 40-bit Accumulator B Carry/Borrow Out Saturate Carry/Borrow In Adder Negate 40 40 40 16 X Data Bus Barrel Shifter 40 Y Data Bus Sign-Extend 32 16 Zero Backfill 32 33 17-bit Multiplier/Scaler 16 16 To/From W Array DS70318F-page 36 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 3.6.1 MULTIPLIER The 17-bit x 17-bit multiplier is capable of signed or unsigned operation and can multiplex its output using a scaler to support either 1.31 fractional (Q31) or 32-bit integer results. Unsigned operands are zero-extended into the 17th bit of the multiplier input value. Signed operands are sign-extended into the 17th bit of the multiplier input value. The output of the 17-bit x 17-bit multiplier/scaler is a 33-bit value that is sign-extended to 40 bits. Integer data is inherently represented as a signed 2's complement value, where the Most Significant bit (MSb) is defined as a sign bit. The range of an N-bit 2's complement integer is -2N-1 to 2N-1 - 1. * For a 16-bit integer, the data range is -32768 (0x8000) to 32767 (0x7FFF) including 0. * For a 32-bit integer, the data range is -2,147,483,648 (0x8000 0000) to 2,147,483,647 (0x7FFF FFFF). When the multiplier is configured for fractional multiplication, the data is represented as a 2's complement fraction, where the MSb is defined as a sign bit and the radix point is implied to lie just after the sign bit (QX format). The range of an N-bit 2's complement fraction with this implied radix point is -1.0 to (1 - 21-N). For a 16-bit fraction, the Q15 data range is -1.0 (0x8000) to 0.999969482 (0x7FFF) including 0 and has a precision of 3.01518x10-5. In Fractional mode, the 16 x 16 multiply operation generates a 1.31 product that has a precision of 4.65661 x 10-10. The same multiplier is used to support the MCU multiply instructions, which include integer 16-bit signed, unsigned and mixed sign multiply operations. The MUL instruction can be directed to use byte or word-sized operands. Byte operands will direct a 16-bit result, and word operands will direct a 32-bit result to the specified register(s) in the W array. 3.6.2 DATA ACCUMULATORS AND ADDER/SUBTRACTER The data accumulator consists of a 40-bit adder/ subtracter with automatic sign extension logic. It can select one of two accumulators (A or B) as its preaccumulation source and post-accumulation destination. For the ADD and LAC instructions, the data to be accumulated or loaded can be optionally scaled using the barrel shifter prior to accumulation. (c) 2008-2012 Microchip Technology Inc. 3.6.2.1 Adder/Subtracter, Overflow and Saturation The adder/subtracter is a 40-bit adder with an optional zero input into one side, and either true or complement data into the other input. * In the case of addition, the Carry/Borrow input is active-high and the other input is true data (not complemented). * In the case of subtraction, the Carry/Borrow input is active-low and the other input is complemented. The adder/subtracter generates Overflow Status bits, SA/SB and OA/OB, which are latched and reflected in the STATUS register: * Overflow from bit 39: this is a catastrophic overflow in which the sign of the accumulator is destroyed. * Overflow into guard bits, 32 through 39: this is a recoverable overflow. This bit is set whenever all the guard bits are not identical to each other. The adder has an additional saturation block that controls accumulator data saturation, if selected. It uses the result of the adder, the Overflow Status bits described previously and the SAT (CORCON<7:6>) and ACCSAT (CORCON<4>) mode control bits to determine when and to what value to saturate. Six STATUS register bits support saturation and overflow: * OA: ACCA overflowed into guard bits * OB: ACCB overflowed into guard bits * SA: ACCA saturated (bit 31 overflow and saturation) or ACCA overflowed into guard bits and saturated (bit 39 overflow and saturation) * SB: ACCB saturated (bit 31 overflow and saturation) or ACCB overflowed into guard bits and saturated (bit 39 overflow and saturation) * OAB: Logical OR of OA and OB * SAB: Logical OR of SA and SB The OA and OB bits are modified each time data passes through the adder/subtracter. When set, they indicate that the most recent operation has overflowed into the accumulator guard bits (bits 32 through 39). The OA and OB bits can also optionally generate an arithmetic warning trap when set and the corresponding Overflow Trap Flag Enable bits (OVATE, OVBTE) in the INTCON1 register are set (refer to Section 7.0 "Interrupt Controller"). This allows the user application to take immediate action, for example, to correct system gain. DS70318F-page 37 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 The SA and SB bits are modified each time data passes through the adder/subtracter, but can only be cleared by the user application. When set, they indicate that the accumulator has overflowed its maximum range (bit 31 for 32-bit saturation or bit 39 for 40-bit saturation) and will be saturated (if saturation is enabled). When saturation is not enabled, SA and SB default to bit 39 overflow and thus, indicate that a catastrophic overflow has occurred. If the COVTE bit in the INTCON1 register is set, SA and SB bits will generate an arithmetic warning trap when saturation is disabled. * W13, Register Direct: The rounded contents of the non-target accumulator are written into W13 as a 1.15 fraction. * [W13] + = 2, Register Indirect with Post-Increment: The rounded contents of the non-target accumulator are written into the address pointed to by W13 as a 1.15 fraction. W13 is then incremented by 2 (for a word write). The Overflow and Saturation Status bits can optionally be viewed in the STATUS Register (SR) as the logical OR of OA and OB (in bit OAB) and the logical OR of SA and SB (in bit SAB). Programmers can check one bit in the STATUS register to determine if either accumulator has overflowed, or one bit to determine if either accumulator has saturated. This is useful for complex number arithmetic, which typically uses both accumulators. The round logic is a combinational block that performs a conventional (biased) or convergent (unbiased) round function during an accumulator write (store). The Round mode is determined by the state of the RND bit in the CORCON register. It generates a 16-bit, 1.15 data value that is passed to the data space write saturation logic. If rounding is not indicated by the instruction, a truncated 1.15 data value is stored and the least significant word is simply discarded. The device supports three Saturation and Overflow modes: * Bit 39 Overflow and Saturation: When bit 39 overflow and saturation occurs, the saturation logic loads the maximally positive 9.31 (0x7FFFFFFFFF) or maximally negative 9.31 value (0x8000000000) into the target accumulator. The SA or SB bit is set and remains set until cleared by the user application. This condition is referred to as `super saturation' and provides protection against erroneous data or unexpected algorithm problems (such as gain calculations). * Bit 31 Overflow and Saturation: When bit 31 overflow and saturation occurs, the saturation logic then loads the maximally positive 1.31 value (0x007FFFFFFF) or maximally negative 1.31 value (0x0080000000) into the target accumulator. The SA or SB bit is set and remains set until cleared by the user application. When this Saturation mode is in effect, the guard bits are not used, so the OA, OB or OAB bits are never set. * Bit 39 Catastrophic Overflow: The bit 39 Overflow Status bit from the adder is used to set the SA or SB bit, which remains set until cleared by the user application. No saturation operation is performed, and the accumulator is allowed to overflow, destroying its sign. If the COVTE bit in the INTCON1 register is set, a catastrophic overflow can initiate a trap exception. 3.6.3 ACCUMULATOR `WRITE BACK' The MAC class of instructions (with the exception of MPY, MPY.N, ED and EDAC) can optionally write a rounded version of the high word (bits 31 through 16) of the accumulator that is not targeted by the instruction into data space memory. The write is performed across the X bus into combined X and Y address space. The following addressing modes are supported: DS70318F-page 38 3.6.3.1 Round Logic Conventional rounding zero-extends bit 15 of the accumulator and adds it to the ACCxH word (bits 16 through 31 of the accumulator). * If the ACCxL word (bits 0 through 15 of the accumulator) is between 0x8000 and 0xFFFF (0x8000 included), ACCxH is incremented. * If ACCxL is between 0x0000 and 0x7FFF, ACCxH is left unchanged. A consequence of this algorithm is that over a succession of random rounding operations, the value tends to be biased slightly positive. Convergent (or unbiased) rounding operates in the same manner as conventional rounding, except when ACCxL equals 0x8000. In this case, the Least Significant bit (bit 16 of the accumulator) of ACCxH is examined: * If it is `1', ACCxH is incremented. * If it is `0', ACCxH is not modified. Assuming that bit 16 is effectively random in nature, this scheme removes any rounding bias that may accumulate. The SAC and SAC.R instructions store either a truncated (SAC), or rounded (SAC.R) version of the contents of the target accumulator to data memory via the X bus, subject to data saturation (see Section 3.6.3.2 "Data Space Write Saturation"). For the MAC class of instructions, the accumulator writeback operation functions in the same manner, addressing combined MCU (X and Y) data space though the X bus. For this class of instructions, the data is always subject to rounding. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 3.6.3.2 Data Space Write Saturation 3.6.4 BARREL SHIFTER In addition to adder/subtracter saturation, writes to data space can also be saturated, but without affecting the contents of the source accumulator. The data space write saturation logic block accepts a 16-bit, 1.15 fractional value from the round logic block as its input, together with overflow status from the original source (accumulator) and the 16-bit round adder. These inputs are combined and used to select the appropriate 1.15 fractional value as output to write to data space memory. The barrel shifter can perform up to 16-bit arithmetic or logic right shifts, or up to 16-bit left shifts in a single cycle. The source can be either of the two DSP accumulators or the X bus (to support multi-bit shifts of register or memory data). If the SATDW bit in the CORCON register is set, data (after rounding or truncation) is tested for overflow and adjusted accordingly: The barrel shifter is 40 bits wide, thereby obtaining a 40-bit result for DSP shift operations and a 16-bit result for MCU shift operations. Data from the X bus is presented to the barrel shifter between bit positions 16 and 31 for right shifts, and between bit positions 0 and 16 for left shifts. * For input data greater than 0x007FFF, data written to memory is forced to the maximum positive 1.15 value, 0x7FFF. * For input data less than 0xFF8000, data written to memory is forced to the maximum negative 1.15 value, 0x8000. The shifter requires a signed binary value to determine both the magnitude (number of bits) and direction of the shift operation. A positive value shifts the operand right. A negative value shifts the operand left. A value of `0' does not modify the operand. The Most Significant bit of the source (bit 39) is used to determine the sign of the operand being tested. If the SATDW bit in the CORCON register is not set, the input data is always passed through unmodified under all conditions. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 39 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 40 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.0 Note: MEMORY ORGANIZATION This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 4. "Program Memory" (DS70202) in the "dsPIC33F/ PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 architecture features separate program and data memory spaces and buses. This architecture also allows the direct access to program memory from the data space during code execution. FIGURE 4-1: 4.1 Program Address Space The program address memory space of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices is 4M instructions. The space is addressable by a 24-bit value derived either from the 23-bit Program Counter (PC) during program execution, or from table operation or data space remapping as described in Section 4.6 "Interfacing Program and Data Memory Spaces". User application access to the program memory space is restricted to the lower half of the address range (0x000000 to 0x7FFFFF). The exception is the use of TBLRD/TBLWT operations, which use TBLPAG<7> to permit access to the Configuration bits and Device ID sections of the configuration memory space. The memory maps for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices are shown in Figure 4-1. PROGRAM MEMORY MAPS FOR dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DEVICES GOTO Instruction Reset Address 0x000000 0x000002 0x000004 Interrupt Vector Table 0x0000FE 0x000100 0x000104 0x0001FE 0x000200 Reserved User Memory Space Alternate Vector Table User Program Flash Memory (1792 instructions) 0x000FFE 0x001000 Unimplemented (Read `0's) User Memory Space dsPIC33FJ06GS101/102/202 dsPIC33FJ16GS402/404/502/504 0x000000 GOTO Instruction 0x000002 Reset Address 0x000004 Interrupt Vector Table 0x0000FE 0x000100 Reserved 0x000104 Alternate Vector Table 0x0001FE 0x000200 User Program Flash Memory (5376 instructions) 0x002BFE 0x002C00 Unimplemented (Read `0's) 0x7FFFFE 0x800000 0x7FFFFE 0x800000 Device Configuration Registers Reserved 0xF7FFFE 0xF80000 0xF80017 0xF80018 Reserved DEVID (2) Reserved (c) 2008-2012 Microchip Technology Inc. 0xFEFFFE 0xFF0000 0xFF0002 0xFFFFFE Configuration Memory Space Configuration Memory Space Reserved Device Configuration Registers 0xF7FFFE 0xF80000 0xF80017 0xF80018 Reserved 0xFEFFFE DEVID (2) Reserved 0xFF0000 0xFF0002 0xFFFFFE DS70318F-page 41 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.1.1 PROGRAM MEMORY ORGANIZATION 4.1.2 All dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices reserve the addresses between 0x00000 and 0x000200 for hard-coded program execution vectors. A hardware Reset vector is provided to redirect code execution from the default value of the PC on device Reset to the actual start of code. A GOTO instruction is programmed by the user application at 0x000000, with the actual address for the start of code at 0x000002. The program memory space is organized in wordaddressable blocks. Although it is treated as 24 bits wide, it is more appropriate consider each address of the program memory as a lower and upper word, with the upper byte of the upper word being unimplemented. The lower word always has an even address, while the upper word has an odd address (see Figure 4-2). The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices also have two interrupt vector tables, located from 0x000004 to 0x0000FF and 0x000100 to 0x0001FF. These vector tables allow each of the device interrupt sources to be handled by separate Interrupt Service Routines (ISRs). A more detailed discussion of the interrupt vector tables is provided in Section 7.1 "Interrupt Vector Table". Program memory addresses are always word-aligned on the lower word, and addresses are incremented or decremented by two during the code execution. This arrangement provides compatibility with data memory space addressing and makes data in the program memory space accessible. FIGURE 4-2: msw Address PROGRAM MEMORY ORGANIZATION 16 8 PC Address (lsw Address) 0 0x000000 0x000002 0x000004 0x000006 00000000 00000000 00000000 00000000 Program Memory `Phantom' Byte (read as `0') DS70318F-page 42 least significant word most significant word 23 0x000001 0x000003 0x000005 0x000007 INTERRUPT AND TRAP VECTORS Instruction Width (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.2 Data Address Space The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CPU has a separate, 16-bitwide data memory space. The data space is accessed using separate Address Generation Units (AGUs) for read and write operations. The data memory maps is shown in Figure 4-3. All Effective Addresses (EAs) in the data memory space are 16 bits wide and point to bytes within the data space. This arrangement gives a data space address range of 64 Kbytes or 32K words. The lower half of the data memory space (that is, when EA<15> = 0) is used for implemented memory addresses, while the upper half (EA<15> = 1) is reserved for the Program Space Visibility area (see Section 4.6.3 "Reading Data from Program Memory Using Program Space Visibility"). All word accesses must be aligned to an even address. Misaligned word data fetches are not supported, so care must be taken when mixing byte and word operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error trap is generated. If the error occurred on a read, the instruction underway is completed. If the error occurred on a write, the instruction is executed but the write does not occur. In either case, a trap is then executed, allowing the system and/or user application to examine the machine state prior to execution of the address Fault. All byte loads into any W register are loaded into the Least Significant Byte. The Most Significant Byte is not modified. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices implement up to 2 Kbytes of data memory. Should an EA point to a location outside of this area, an all-zero word or byte will be returned. A sign-extend instruction (SE) is provided to allow user applications to translate 8-bit signed data to 16-bit signed values. Alternatively, for 16-bit unsigned data, user applications can clear the MSB of any W register by executing a zero-extend (ZE) instruction on the appropriate address. 4.2.1 4.2.3 DATA SPACE WIDTH The data memory space is organized in byte addressable, 16-bit wide blocks. Data is aligned in data memory and registers as 16-bit words, but all data space EAs resolve to bytes. The Least Significant Bytes (LSBs) of each word have even addresses, while the Most Significant Bytes (MSBs) have odd addresses. 4.2.2 DATA MEMORY ORGANIZATION AND ALIGNMENT To maintain backward compatibility with PIC(R) MCU devices and improve data space memory usage efficiency, the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 instruction set supports both word and byte operations. As a consequence of byte accessibility, all effective address calculations are internally scaled to step through word-aligned memory. For example, the core recognizes that Post-Modified Register Indirect Addressing mode [Ws++] that results in a value of Ws + 1 for byte operations and Ws + 2 for word operations. Data byte reads will read the complete word that contains the byte, using the LSB of any EA to determine which byte to select. The selected byte is placed onto the LSB of the data path. That is, data memory and registers are organized as two parallel byte-wide entities with shared (word) address decode but separate write lines. Data byte writes only write to the corresponding side of the array or register that matches the byte address. (c) 2008-2012 Microchip Technology Inc. SFR SPACE The first 2 Kbytes of the near data space, from 0x0000 to 0x07FF, is primarily occupied by Special Function Registers (SFRs). These are used by the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 core and peripheral modules for controlling the operation of the device. SFRs are distributed among the modules that they control, and are generally grouped together by module. Much of the SFR space contains unused addresses; these are read as `0'. Note: 4.2.4 The actual set of peripheral features and interrupts varies by the device. Refer to the corresponding device tables and pinout diagrams for device-specific information. NEAR DATA SPACE The 8-Kbyte area between 0x0000 and 0x1FFF is referred to as the near data space. Locations in this space are directly addressable via a 13-bit absolute address field within all memory direct instructions. Additionally, the whole data space is addressable using MOV instructions, which support Memory Direct Addressing mode with a 16-bit address field, or by using Indirect Addressing mode using a working register as an Address Pointer. DS70318F-page 43 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 4-3: DATA MEMORY MAP FOR dsPIC33FJ06GS101/102 DEVICES WITH 256 BYTES OF RAM MSB Address MSb 2-Kbyte SFR Space 256 bytes SRAM Space LSb 0x0000 0x0001 SFR Space 0x07FF 0x0801 0x087F 0x0881 0x07FE 0x0800 X Data RAM (X) Y Data RAM (Y) 0x087E 0x0880 0x08FF 0x0901 0x08FE 0x0900 0x1FFF 0x2001 0x1FFE 0x8001 0x8000 8-Kbyte Near Data Space 0x2000 X Data Unimplemented (X) Optionally Mapped into Program Memory 0xFFFF DS70318F-page 44 LSB Address 16 bits 0xFFFE (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 4-4: DATA MEMORY MAP FOR dsPIC33FJ06GS202 DEVICE WITH 1 KB RAM MSB Address MSb 2-Kbyte SFR Space 1-Kbyte SRAM Space LSB Address 16 bits LSb 0x0000 0x0001 SFR Space 0x07FF 0x0801 0x09FF 0x0A01 0x07FE 0x0800 X Data RAM (X) Y Data RAM (Y) 0x09FE 0x0A00 0x0BFF 0x0C01 0x0BFE 0x0C00 0x1FFF 0x2001 0x1FFE 0x8001 0x8000 8-Kbyte Near Data Space 0x2000 X Data Unimplemented (X) Optionally Mapped into Program Memory 0xFFFF (c) 2008-2012 Microchip Technology Inc. 0xFFFE DS70318F-page 45 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 4-5: DATA MEMORY MAP FOR dsPIC33FJ16GS402/404/502/504 DEVICES WITH 2 KB RAM MSB Address MSb 2-Kbyte SFR Space 2-Kbyte SRAM Space LSb 0x0000 0x0001 SFR Space 0x07FF 0x0801 0x0BFF 0x0C01 0x07FE 0x0800 X Data RAM (X) Y Data RAM (Y) 0x0BFE 0x0C00 0x0FFF 0x1001 0x0FFE 0x1000 0x1FFF 0x2001 0x1FFE 0x8001 0x8000 8-Kbyte Near Data Space 0x2000 X Data Unimplemented (X) Optionally Mapped into Program Memory 0xFFFF DS70318F-page 46 LSB Address 16 bits 0xFFFE (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.2.5 X AND Y DATA SPACES The core has two data spaces, X and Y. These data spaces can be considered either separate (for some DSP instructions), or as one unified linear address range (for MCU instructions). The data spaces are accessed using two Address Generation Units (AGUs) and separate data paths. This feature allows certain instructions to concurrently fetch two words from RAM, thereby enabling efficient execution of DSP algorithms, such as Finite Impulse Response (FIR) filtering and Fast Fourier Transform (FFT). The X data space is used by all instructions and supports all addressing modes. X data space has separate read and write data buses. The X read data bus is the read data path for all instructions that view data space as combined X and Y address space. It is also the X data prefetch path for the dual operand DSP instructions (MAC class). (c) 2008-2012 Microchip Technology Inc. The Y data space is used in concert with the X data space by the MAC class of instructions (CLR, ED, EDAC, MAC, MOVSAC, MPY, MPY.N and MSC) to provide two concurrent data read paths. Both the X and Y data spaces support Modulo Addressing mode for all instructions, subject to addressing mode restrictions. Bit-Reversed Addressing mode is only supported for writes to X data space. All data memory writes, including in DSP instructions, view data space as combined X and Y address space. The boundary between the X and Y data spaces is device-dependent and is not user-programmable. All effective addresses are 16 bits wide and point to bytes within the data space. Therefore, the data space address range is 64 Kbytes, or 32K words, though the implemented memory locations vary by device. DS70318F-page 47 SFR Name SFR Addr CPU CORE REGISTER MAP Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets WREG0 0000 Working Register 0 0000 WREG1 0002 Working Register 1 0000 WREG2 0004 Working Register 2 0000 WREG3 0006 Working Register 3 0000 WREG4 0008 Working Register 4 0000 WREG5 000A Working Register 5 0000 WREG6 000C Working Register 6 0000 WREG7 000E Working Register 7 0000 WREG8 0010 Working Register 8 0000 WREG9 0012 Working Register 9 0000 WREG10 0014 Working Register 10 0000 WREG11 0016 Working Register 11 0000 WREG12 0018 Working Register 12 0000 WREG13 001A Working Register 13 0000 WREG14 001C Working Register 14 0000 WREG15 001E Working Register 15 0800 SPLIM 0020 Stack Pointer Limit Register xxxx ACCAL 0022 ACCAL xxxx ACCAH 0024 ACCAH xxxx ACCAU 0026 ACCBL 0028 ACCA<39> ACCBL xxxx ACCBH 002A ACCBH xxxx ACCB<39> ACCA<39> ACCA<39> ACCB<39> ACCB<39> ACCA<39> ACCA<39> ACCB<39> ACCB<39> ACCA<39> ACCB<39> ACCA<39> ACCA<39> ACCAU ACCB<39> ACCB<39> xxxx (c) 2008-2012 Microchip Technology Inc. ACCBU 002C PCL 002E PCH 0030 -- -- -- -- -- -- -- -- Program Counter High Byte Register 0000 TBLPAG 0032 -- -- -- -- -- -- -- -- Table Page Address Pointer Register 0000 PSVPAG 0034 -- -- -- -- -- -- -- -- Program Memory Visibility Page Address Pointer Register RCOUNT 0036 DCOUNT 0038 003A DOSTARTH 003C DOENDL 003E DOENDH 0040 -- -- -- -- -- -- -- -- SR 0042 OA OB SA SB OAB SAB DA DC CORCON 0044 -- -- -- US EDT 0046 XMODEN YMODEN -- -- MODCON xxxx 0000 0000 Repeat Loop Counter Register DOSTARTL Legend: ACCBU Program Counter Low Word Register xxxx DCOUNT<15:0> xxxx DOSTARTL<15:1> -- -- -- -- -- -- -- -- -- -- DL<2:0> BWM<3:0> x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- 0 xxxx 00xx DOENDH IPL<2:0> SATA xxxx DOSTARTH<5:0> DOENDL<15:1> -- 0 SATB SATDW YWM<3:0> 00xx RA N OV Z C 0000 ACCSAT IPL3 PSV RND IF 0020 XWM<3:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 48 TABLE 4-1: SFR Name CPU CORE REGISTER MAP (CONTINUED) SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets XMODSRT 0048 XS<15:1> 0 xxxx XMODEND 004A XE<15:1> 1 xxxx YMODSRT 004C YS<15:1> 0 xxxx YMODEND 004E YE<15:1> 1 xxxx XBREV 0050 BREN DISICNT 0052 -- Legend: XB<14:0> -- xxxx Disable Interrupts Counter Register xxxx x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJ06GS101 TABLE 4-2: SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 CNEN1 0060 -- -- -- -- -- -- -- -- CN7IE CN6IE CN5IE CN4IE CN3IE CN2IE CNPU1 0068 -- -- -- -- -- -- -- -- CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE File Name Legend: Bit 6 Bit 5 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 CNEN1 0060 CN15IE CN14IE CN13IE CN12IE CN11IE CN10IE CN9IE CN8IE CN7IE CN6IE CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE Bit 2 Bit 0 All Resets CN1IE CN0IE 0000 CN1PUE CN0PUE 0000 Bit 1 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 CN5IE CN4IE CN3IE CN2IE CN1IE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE Bit 2 Bit 1 Bit 0 CN0IE All Resets 0000 CN0PUE 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-4: File Name Bit 3 CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJ06GS102, dsPIC33FJ06GS202, dsPIC33FJ16GS402 AND dsPIC33FJ16GS502 SFR Addr Legend: Bit 4 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-3: File Name Bit 7 SFR Addr CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJ16GS404 AND dsPIC33FJ16GS504 Bit 15 DS70318F-page 49 Bit 13 Bit 12 CN14IE CN13IE CN12IE CN11IE CN10IE CN9IE CN8IE CN7IE CN6IE CN5IE CN4IE CN3IE CN2IE CN1IE CN0IE 0000 -- CN29IE CN28IE CN27IE CN26IE CN25IE CN24IE CN23IE CN22IE CN21IE CN20IE CN19IE CN18IE CN17IE CN16IE 0000 CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE 0000 CNPU2 006A CNEN1 0060 CN15IE CNEN2 0062 Legend: -- -- -- Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 0 All Resets Bit 14 CN29PUE CN28PUE CN27PUE CN26PUE CN25PUE CN24PUE CN23PUE CN22PUE CN21PUE CN20PUE CN19PUE CN18PUE CN17PUE CN16PUE 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-1: File Name INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ06GS101 DEVICES ONLY SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets INTCON1 0080 NSTDIS OVAERR STKERR OSCFAIL -- 0000 INTCON2 0082 ALTIVT DISI -- -- -- -- -- -- -- -- -- -- -- INT2EP INT1EP INT0EP 0000 IFS0 0084 -- -- ADIF U1TXIF U1RXIF SPI1IF SPI1EIF -- T2IF -- -- -- T1IF OC1IF -- INT0IF 0000 IFS1 0086 -- -- INT2IF -- -- -- -- -- -- -- -- INT1IF CNIF -- MI2C1IF SI2C1IF 0000 IFS3 008A -- -- -- -- -- -- PSEMIF -- -- -- -- -- -- -- -- -- 0000 IFS4 008C -- -- -- -- -- -- -- -- -- -- -- -- -- -- U1EIF -- 0000 IFS5 008E -- PWM1IF -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 IFS6 0090 ADCP1IF ADCP0IF -- -- -- -- -- -- -- -- -- -- -- -- PWM4IF -- 0000 IFS7 0092 -- -- -- -- -- -- -- -- -- -- -- -- -- -- ADCP3IF -- 0000 IEC0 0094 -- -- ADIE U1TXIE U1RXIE SPI1IE SPI1EIE -- T2IE -- -- -- T1IE OC1IE -- INT0IE 0000 IEC1 0096 -- -- INT2IE -- -- -- -- -- -- -- -- INT1IE CNIE -- MI2C1IE IEC2 0098 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 IEC3 009A -- -- -- -- -- -- PSEMIE -- -- -- -- -- -- -- -- -- 0000 IEC4 009C -- -- -- -- -- -- -- -- -- -- -- -- -- -- U1EIE -- 0000 IEC5 009E -- PWM1IE -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 ADCP0IE -- -- -- -- -- -- -- -- -- -- -- -- PWM4IE -- 0000 -- -- -- -- -- -- -- -- -- -- -- -- -- ADCP3IE -- 0000 -- -- -- -- -- -- -- -- -- -- -- -- -- OVBERR COVAERR COVBERR OVATE (c) 2008-2012 Microchip Technology Inc. IEC6 00A0 ADCP1IE IEC7 00A2 -- IPC0 00A4 -- T1IP<2:0> -- IPC1 00A6 -- T2IP<2:0> -- IPC2 00A8 -- IPC3 00AA -- IPC4 00AC -- IPC5 00AE -- -- -- IPC7 00B2 -- -- IPC14 00C0 -- -- IPC16 00C4 -- IPC23 00D2 IPC24 IPC27 IPC28 00DC -- -- -- -- INTTREG 00E0 -- -- -- -- Legend: U1RXIP<2:0> OVBTE COVTE SFTACERR DIV0ERR OC1IP<2:0> -- SI2C1IE 0000 INT0IP<2:0> 4404 -- -- 4000 -- -- 4440 -- SPI1EIP<2:0> -- -- -- -- --- ADIP<2:0> -- U1TXIP<2:0> 0044 -- -- -- -- -- MI2C1IP<2:0> -- SI2C1IP<2:0> 4044 -- -- -- -- -- -- -- INT1IP<2:0> 0004 -- -- -- -- -- -- -- INT2IP<2:0> -- -- -- -- 0040 -- -- -- -- -- -- -- PSEMIP<2:0> -- -- -- -- 0040 -- -- -- -- -- -- -- -- U1EIP<2:0> -- -- -- -- 0400 -- -- -- -- -- -- -- -- -- 0040 00D4 -- -- -- -- -- -- -- -- -- 4400 00DA -- -- -- -- -- 0040 -- -- -- -- 0000 -- -- CNIP<2:0> ADCP1IP<2:0> SPI1IP<2:0> MATHERR ADDRERR -- -- -- -- -- PWM1IP<2:0> -- -- -- -- -- -- ADCP0IP<2:0> -- -- ILR<3:0> x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- -- -- -- -- -- -- -- -- -- -- PWM4IP<2:0> -- -- ADCP3IP<2:0> -- VECNUM<6:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 50 TABLE 4-5: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ06GS102 DEVICES ONLY File Name SFR Addr. Bit 15 Bit 14 INTCON1 0080 NSTDIS OVAERR INTCON2 0082 ALTIVT DISI -- -- -- -- -- -- -- -- -- -- IFS0 0084 -- -- ADIF U1TXIF U1RXIF SPI1IF SPI1EIF -- T2IF -- -- -- IFS1 0086 -- -- INT2IF -- -- -- -- -- -- -- -- INT1IF IFS3 008A -- -- -- -- -- -- PSEMIF -- -- -- -- IFS4 008C -- -- -- -- -- -- -- -- -- -- IFS5 008E PWM2IF PWM1IF -- -- -- -- -- -- -- -- IFS6 0090 ADCP1IF ADCP0IF -- -- -- -- -- -- -- IFS7 0092 -- -- -- -- -- -- -- -- IEC0 0094 -- -- ADIE U1TXIE U1RXIE SPI1IE SPI1EIE IEC1 0096 -- -- INT2IE -- -- -- -- IEC3 009A -- -- -- -- -- -- IEC4 009C -- -- -- -- -- -- Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 OVBERR COVAERR COVBERR OVATE Bit 7 Bit 6 Bit 1 Bit 0 STKERR OSCFAIL -- 0000 -- INT2EP INT1EP INT0EP 0000 T1IF OC1IF -- INT0IF 0000 CNIF -- MI2C1IF SI2C1IF 0000 -- -- -- -- -- 0000 -- -- -- -- U1EIF -- 0000 -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- T2IE -- -- -- T1IE OC1IE -- -- -- -- -- INT1IE CNIE -- MI2C1IE PSEMIE -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- U1EIE -- 0000 COVTE SFTACERR DIV0ERR Bit 5 -- Bit 4 Bit 3 All Resets Bit 2 OVBTE Bit 8 MATHERR ADDRERR ADCP2IF 0000 INT0IE 0000 SI2C1IE 0000 DS70318F-page 51 IEC5 009E PWM2IE PWM1IE -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 IEC6 00A0 ADCP1IE ADCP0IE -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 IEC7 00A2 -- -- -- -- -- -- -- -- -- -- -- -- -- -- IPC0 00A4 -- -- -- -- -- -- IPC1 00A6 -- -- -- -- IPC2 00A8 IPC3 00AA -- IPC4 00AC -- IPC5 00AE -- -- -- IPC7 00B2 -- -- -- IPC14 00C0 -- -- IPC16 00C4 -- -- IPC23 00D2 -- PWM2IP<2:0> -- PWM1IP<2:0> -- -- -- IPC27 00DA -- ADCP1IP<2:0> -- ADCP0IP<2:0> -- -- -- IPC28 00DC -- -- -- -- -- -- -- INTTREG 00E0 -- -- -- -- Legend: -- T1IP<2:0> -- -- T2IP<2:0> -- -- U1RXIP<2:0> -- -- -- -- OC1IP<2:0> -- -- -- SPI1IP<2:0> ADCP2IE 0000 INT0IP<2:0> 4404 -- -- -- -- 4000 -- SPI1EIP<2:0> -- -- -- -- 4440 -- -- -- -- --- ADIP<2:0> -- U1TXIP<2:0> 0044 -- -- -- -- -- MI2C1IP<2:0> -- SI2C1IP<2:0> 4044 -- -- -- -- -- -- -- -- -- -- -- -- INT2IP<2:0> -- -- -- -- 0040 -- -- -- -- -- -- -- PSEMIP<2:0> -- -- -- -- 0040 -- -- -- -- -- -- -- U1EIP<2:0> -- -- -- -- 0040 -- -- -- -- -- 4400 -- -- -- -- -- 4400 -- -- CNIP<2:0> -- -- ILR<3:0> -- -- -- x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- -- -- -- VECNUM<6:0> INT1IP<2:0> ADCP2IP<2:0> 0004 0004 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-6: File Name INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ06G202 DEVICES ONLY SFR Addr. Bit 15 Bit 14 Bit 13 INTCON1 0080 NSTDIS OVAERR OVBERR INTCON2 0082 ALTIVT DISI -- -- -- IFS0 0084 -- -- ADIF U1TXIF IFS1 0086 -- -- INT2IF IFS3 008A -- -- -- IFS4 008C -- -- IFS5 008E PWM2IF (c) 2008-2012 Microchip Technology Inc. Bit 9 Bit 8 OVATE OVBTE COVTE -- -- -- -- -- -- -- -- U1RXIF SPI1IF SPI1EIF -- T2IF -- -- -- -- -- -- -- -- -- -- -- -- -- -- PSEMIF -- -- -- -- -- -- -- -- -- -- -- -- PWM1IF -- -- -- -- -- -- -- IFS6 0090 ADCP1IF ADCP0IF -- -- -- -- -- -- IFS7 0092 -- -- -- -- -- -- -- -- IEC0 0094 -- -- ADIE U1TXIE U1RXIE SPI1IE SPI1EIE IEC1 0096 -- -- INT2IE -- -- -- -- IEC3 009A -- -- -- -- -- -- IEC4 009C -- -- -- -- -- -- IEC5 009E PWM2IE PWM1IE -- -- -- IEC6 00A0 ADCP1IE ADCP0IE -- -- IEC7 00A2 -- -- -- IPC0 00A4 -- T1IP<2:0> -- IPC1 00A6 -- T2IP<2:0> -- IPC2 00A8 -- U1RXIP<2:0> -- IPC3 00AA -- IPC4 00AC -- IPC5 00AE -- -- -- -- -- -- -- -- -- IPC7 00B2 -- -- -- -- -- -- -- -- -- INT2IP<2:0> -- -- -- -- 0040 IPC14 00C0 -- -- -- -- -- -- -- -- -- PSEMIP<2:0> -- -- -- -- 0040 IPC16 00C4 -- -- -- -- -- -- -- -- -- U1EIP<2:0> -- -- -- -- 0040 IPC23 00D2 -- PWM2IP<2:0> -- IPC25 00D6 -- AC2IP<2:0> -- IPC27 00DA -- IPC28 00DC -- -- -- -- -- -- -- -- IPC29 00DE -- -- -- -- -- -- -- -- INTTREG 00E0 -- -- -- -- Legend: -- Bit 11 Bit 2 Bit 1 STKERR OSCFAIL -- 0000 INT2EP INT1EP INT0EP 0000 T1IF OC1IF IC1IF INT0IF 0000 INT1IF CNIF AC1IF MI2C1IF SI2C1IF 0000 -- -- -- -- -- 0000 -- -- -- -- U1EIF -- 0000 -- -- -- -- -- -- -- 0000 AC2IF -- -- -- -- -- -- -- 0000 -- -- -- ADCP6IF -- -- -- -- T2IE -- -- -- T1IE OC1IE IC1IE -- -- -- -- INT1IE CNIE AC1IE MI2C1IE PSEMIE -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- U1EIE -- 0000 -- -- -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- AC2IE -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- ADCP6IE -- -- COVAERR COVBERR -- -- CNIP<2:0> -- -- -- -- -- SPI1IP<2:0> -- -- -- PWM1IP<2:0> -- -- Bit 5 -- -- ADCP0IP<2:0> ILR<3:0> x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- Bit 4 -- Bit 3 MATHERR ADDRERR IC1IP<2:0> INT0IE 0000 SI2C1IE 0000 ADCP2IE 0000 INT0IP<2:0> 4444 -- -- 4000 SPI1EIP<2:0> -- -- -- -- 4440 --- ADIP<2:0> -- U1TXIP<2:0> 0044 -- MI2C1IP<2:0> -- SI2C1IP<2:0> 4444 -- INT1IP<2:0> -- -- -- ADCP2IF 0000 -- -- -- -- Bit 0 -- -- AC1IP<2:0> -- Bit 6 SFTACERR DIV0ERR OC1IP<2:0> -- ADCP1IP<2:0> Bit 7 All Resets Bit 10 -- Bit 12 -- 0004 -- -- -- -- -- -- -- -- 4400 -- -- -- -- -- -- -- -- 4000 -- -- -- -- -- -- -- -- 4400 -- -- -- -- -- ADCP2IP<2:0> 0004 -- -- -- -- -- ADCP6IP<2:0> 0004 -- VECNUM<6:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 52 TABLE 4-7: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ16GS402/404 DEVICES ONLY DS70318F-page 53 File Name SFR Addr. Bit 15 Bit 14 INTCON1 0080 NSTDIS OVAERR INTCON2 0082 ALTIVT DISI -- -- -- IFS0 0084 -- -- ADIF U1TXIF U1RXIF IFS1 0086 -- -- INT2IF -- -- -- IFS3 008A -- -- -- -- -- IFS4 008C -- -- -- -- IFS5 008E PWM2IF PWM1IF -- -- IFS6 0090 ADCP1IF ADCP0IF -- IFS7 0092 -- -- IEC0 0094 -- IEC1 0096 -- IEC3 009A IEC4 009C IEC5 009E IEC6 IEC7 00A2 -- IPC0 00A4 -- IPC1 00A6 IPC2 00A8 IPC3 00AA -- IPC4 00AC -- IPC5 00AE -- -- -- IPC7 00B2 -- -- -- IPC14 00C0 -- -- IPC16 00C4 -- -- IPC23 00D2 -- IPC24 00D4 -- IPC27 00DA -- IPC28 00DC -- -- -- -- INTTREG 00E0 -- -- -- -- Legend: Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 OVBERR COVAERR COVBERR OVATE OVBTE Bit 7 Bit 6 Bit 5 COVTE SFTACERR DIV0ERR Bit 3 MATHERR ADDRERR All Resets Bit 2 Bit 1 Bit 0 STKERR OSCFAIL -- 0000 -- -- -- -- -- -- INT2EP INT1EP INT0EP 0000 T2IF OC2IF IC2IF -- T1IF OC1IF IC1IF INT0IF 0000 -- -- -- -- -- INT1IF CNIF -- MI2C1IF SI2C1IF 0000 -- PSEMIF -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- -- -- U1EIF -- 0000 -- -- -- -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- -- -- -- -- PWM3IF 0000 -- -- -- -- -- -- -- -- -- -- -- -- ADCP3IF ADCP2IF 0000 -- ADIE U1TXIE U1RXIE T3IE T2IE OC2IE IC2IE -- T1IE OC1IE IC1IE -- INT2IE -- -- -- -- -- -- -- -- INT1IE CNIE -- MI2C1IE -- -- -- -- -- -- PSEMIE -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- -- -- -- -- -- -- U1EIE -- 0000 PWM2IE PWM1IE -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 00A0 ADCP1IE ADCP0IE -- -- -- -- -- -- -- -- -- -- -- -- -- PWM3IE 0000 -- -- -- -- -- -- -- -- -- -- -- -- ADCP3IE ADCP2IE 0000 T1IP<2:0> -- -- T2IP<2:0> -- U1RXIP<2:0> -- -- -- SPI1IF SPI1EIF SPI1IE SPI1EIE OC1IP<2:0> -- -- OC2IP<2:0> -- SPI1IP<2:0> INT0IE 0000 SI2C1IE 0000 IC1IP<2:0> -- INT0IP<2:0> -- IC2IP<2:0> -- -- SPI1EIP<2:0> -- T3IP<2:0> 4444 -- -- 4444 -- 4440 -- -- -- -- --- ADIP<2:0> -- U1TXIP<2:0> 0044 -- -- -- -- -- MI2C1IP<2:0> -- SI2C1IP<2:0> 4044 -- -- -- -- -- -- -- -- -- -- -- -- INT2IP<2:0> -- -- -- -- 0040 -- -- -- -- -- -- -- PSEMIP<2:0> -- -- -- -- 0040 -- -- -- -- -- -- -- U1EIP<2:0> -- -- -- -- 0040 -- -- -- -- 4400 CNIP<2:0> PWM2IP<2:0> -- -- -- Bit 4 T3IF -- -- Bit 8 -- -- -- ADCP1IP<2:0> -- PWM1IP<2:0> -- -- -- -- --- -- ADCP0IP<2:0> -- ILR<3:0> -- -- -- -- -- -- -- -- -- -- -- -- --- -- -- -- ADCP3IP<2:0> -- -- x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. INT1IP<2:0> VECNUM<6:0> 0004 PWM3IP<2:0> -- -- ADCP2IP<2:0> 0004 -- 4400 0044 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-8: File Name INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ16GS502 DEVICES ONLY (c) 2008-2012 Microchip Technology Inc. SFR Addr. Bit 15 Bit 14 INTCON1 0080 NSTDIS OVAERR INTCON2 0082 ALTIVT DISI -- -- -- -- -- -- -- -- -- -- -- IFS0 0084 -- -- ADIF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF -- IFS1 0086 -- -- INT2IF -- -- -- -- -- -- -- -- IFS3 008A -- -- -- -- -- -- PSEMIF -- -- -- IFS4 008C -- -- -- -- -- -- -- -- -- IFS5 008E PWM2IF PWM1IF -- -- -- -- -- -- IFS6 0090 ADCP1IF ADCP0IF -- -- -- -- AC4IF AC3IF IFS7 0092 -- -- -- -- -- -- -- -- -- IEC0 0094 -- -- ADIE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE IEC1 0096 -- -- INT2IE -- -- -- -- -- -- IEC3 009A -- -- -- -- -- -- PSEMIE -- IEC4 009C -- -- -- -- -- -- -- -- IEC5 009E PWM2IE PWM1IE -- -- -- -- -- IEC6 00A0 ADCP1IE ADCP0IE -- -- -- -- IEC7 00A2 -- -- -- -- -- IPC0 00A4 -- T1IP<2:0> -- OC1IP<2:0> -- IC1IP<2:0> -- IPC1 00A6 -- T2IP<2:0> -- OC2IP<2:0> -- IC2IP<2:0> --- IPC2 00A8 -- U1RXIP<2:0> -- SPI1IP<2:0> -- SPI1EIP<2:0> -- T3IP<2:0> 4444 IPC3 00AA -- --- -- --- ADIP<2:0> -- U1TXIP<2:0> 0044 IPC4 00AC -- -- AC1IP<2:0> -- MI2C1IP<2:0> -- SI2C1IP<2:0> 4444 IPC5 00AE -- -- -- -- -- -- -- -- -- -- INT1IP<2:0> IPC7 00B2 -- -- -- -- -- -- -- -- -- INT2IP<2:0> -- -- -- -- 0040 IPC14 00C0 -- -- -- -- -- -- -- -- -- PSEMIP<2:0> -- -- -- -- 0040 IPC16 00C4 -- -- -- -- -- -- -- -- -- U1EIP<2:0> -- -- -- -- 0040 IPC23 00D2 -- -- -- -- -- 4400 IPC24 00D4 -- IPC25 00D6 -- IPC26 00D8 -- IPC27 00DA -- IPC28 00DC -- -- -- -- -- -- -- IPC29 00DE -- -- -- -- -- -- -- INTTREG 00E0 -- -- -- -- Legend: -- -- Bit 13 Bit 12 -- -- PWM2IP<2:0> -- -- -- AC2IP<2:0> -- Bit 10 Bit 9 OVBERR COVAERR COVBERR OVATE CNIP<2:0> -- Bit 11 -- -- ADCP1IP<2:0> Bit 8 Bit 7 Bit 6 Bit 5 Bit 1 STKERR OSCFAIL -- 0000 INT2EP INT1EP INT0EP 0000 T1IF OC1IF IC1IF INT0IF 0000 INT1IF CNIF AC1IF MI2C1IF SI2C1IF 0000 -- -- -- -- -- -- 0000 -- -- -- -- -- U1EIF -- 0000 -- -- -- -- -- -- -- -- 0000 AC2IF -- -- -- -- -- PWM4IF PWM3IF 0000 -- -- ADCP6IF -- -- ADCP3IF ADCP2IF 0000 OC2IE IC2IE -- T1IE OC1IE IC1IE -- -- INT1IE CNIE AC1IE MI2C1IE -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- U1EIE -- 0000 -- -- -- -- -- -- -- -- -- 0000 AC4IE AC3IE AC2IE -- -- -- -- -- PWM4IE PWM3IE 0000 -- -- -- -- -- ADCP6IE -- -- ADCP3IE ADCP2IE 0000 PWM1IP<2:0> -- -- -- -- Bit 3 MATHERR ADDRERR -- -- -- -- INT0IE INT0IP<2:0> -- -- 4444 -- 4440 0004 -- -- -- -- -- -- -- -- -- -- -- -- -- -- AC4IP<2:0> -- --- -- -- -- -- ADCP3IP<2:0> -- ADCP2IP<2:0> 0044 -- -- -- ADCP6IP<2:0> 0004 ADCP0IP<2:0> ILR<3:0> -- x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- -- -- -- -- 0000 SI2C1IE 0000 -- -- PWM4IP<2:0> Bit 0 All Resets Bit 2 OVBTE COVTE SFTACERR DIV0ERR Bit 4 -- -- -- VECNUM<6:0> PWM3IP<2:0> -- -- 0044 -- AC3IP<2:0> -- -- 4000 0044 -- 4400 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 54 TABLE 4-9: File Name INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ16GS504 DEVICES ONLY SFR Addr. Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets DS70318F-page 55 INTCON1 0080 NSTDIS OVAERR OVATE OVBTE STKERR OSCFAIL -- 0000 INTCON2 0082 ALTIVT DISI -- -- -- -- -- -- -- -- -- -- -- INT2EP INT1EP INT0EP 0000 IFS0 0084 -- -- ADIF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF T2IF OC2IF IC2IF -- T1IF OC1IF IC1IF INT0IF 0000 IFS1 0086 -- -- INT2IF -- -- -- -- -- -- -- -- INT1IF CNIF AC1IF MI2C1IF SI2C1IF 0000 IFS3 008A -- -- -- -- -- -- PSEMIF -- -- -- -- -- -- -- -- -- 0000 IFS4 008C -- -- -- -- -- -- -- -- -- -- -- -- -- -- U1EIF -- 0000 IFS5 008E PWM2IF PWM1IF -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 IFS6 0090 ADCP1IF ADCP0IF -- -- -- -- AC4IF AC3IF AC2IF -- -- -- -- -- PWM4IF PWM3IF 0000 IFS7 0092 -- -- -- -- -- -- -- -- -- -- -- ADCP6IF ADCP5IF ADCP4IF ADCP3IF ADCP2IF 0000 IEC0 0094 -- -- ADIE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE T2IE OC2IE IC2IE -- T1IE OC1IE IC1IE IEC1 0096 -- -- INT2IE -- -- -- -- -- -- -- -- INT1IE CNIE AC1IE MI2C1IE IEC3 009A -- -- -- -- -- -- PSEMIE -- -- -- -- -- -- -- -- -- 0000 IEC4 009C -- -- -- -- -- -- -- -- -- -- -- -- -- -- U1EIE -- 0000 IEC5 009E PWM2IE PWM1IE -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0000 IEC6 00A0 ADCP1IE ADCP0IE -- -- -- -- AC4IE AC3IE AC2IE -- -- -- -- -- PWM4IE PWM3IE 0000 IEC7 00A2 -- -- -- -- -- -- -- -- -- -- ADCP6IE ADCP5IE ADCP4IE ADCP3IE ADCP2IE 0000 IPC0 00A4 -- T1IP<2:0> -- OC1IP<2:0> -- IC1IP<2:0> -- IPC1 00A6 -- T2IP<2:0> -- OC2IP<2:0> -- IC2IP<2:0> -- IPC2 00A8 -- U1RXIP<2:0> -- SPI1IP<2:0> -- SPI1EIP<2:0> -- T3IP<2:0> 4444 IPC3 00AA -- --- ADIP<2:0> -- U1TXIP<2:0> 0044 IPC4 00AC -- -- MI2C1IP<2:0> -- SI2C1IP<2:0> 4444 IPC5 00AE -- -- -- -- -- -- -- -- -- -- INT1IP<2:0> IPC7 00B2 -- -- -- -- -- -- -- -- -- INT2IP<2:0> -- -- -- -- 0040 IPC14 00C0 -- -- -- -- -- -- -- -- -- PSEMIP<2:0> -- -- -- -- 0040 IPC16 00C4 -- -- -- -- -- -- -- -- -- U1EIP<2:0> -- -- -- -- 0040 IPC23 00D2 -- -- -- -- -- 4400 IPC24 00D4 -- IPC25 00D6 -- IPC26 00D8 -- IPC27 00DA -- ADCP1IP<2:0> -- ADCP0IP<2:0> -- IPC28 00DC -- ADCP5IP<2:0> -- ADCP4IP<2:0> -- IPC29 00DE -- -- -- -- INTTREG 00E0 -- -- -- -- Legend: -- -- OVBERR COVAERR COVBERR -- -- CNIP<2:0> -- -- -- -- -- -- AC1IP<2:0> -- AC2IP<2:0> -- -- -- PWM2IP<2:0> -- -- COVTE SFTACERR DIV0ERR PWM1IP<2:0> -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ILR<3:0> x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- -- -- -- -- MATHERR ADDRERR -- -- -- -- PWM4IP<2:0> -- -- AC4IP<2:0> -- -- -- -- -- -- -- -- -- -- -- -- 4440 0004 0044 -- AC3IP<2:0> -- 0000 4444 -- PWM3IP<2:0> -- ADCP3IP<2:0> -- INT0IP<2:0> -- -- INT0IE SI2C1IE 0000 4000 0440 -- 4400 -- ADCP2IP<2:0> 4444 -- ADCP6IP<2:0> 0004 VECNUM<6:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-10: SFR Name TMR1 SFR Addr TIMER REGISTER MAP FOR dsPIC33FJ06GS101 AND dsPIC33FJ06GSX02 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0100 Timer1 Register 0000 PR1 0102 Period Register 1 FFFF T1CON 0104 TMR2 0106 Timer2 Register PR2 010C Period Register 2 TON -- TSIDL TSIDL -- -- -- -- -- -- -- -- -- -- -- -- T2CON 0110 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-12: SFR Name SFR Addr TON -- TGATE TCKPS<1:0> -- TSYNC TCS -- 0000 0000 FFFF TGATE TCKPS<1:0> -- -- TCS -- 0000 Bit 3 Bit 2 Bit 1 Bit 0 All Resets TIMER REGISTER MAP FOR dsPIC33FJ16GSX02 AND dsPIC33FJ16GSX04 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 TMR1 0100 Timer1 Register PR1 0102 Period Register 1 Bit 5 Bit 4 0000 FFFF (c) 2008-2012 Microchip Technology Inc. T1CON 0104 TMR2 0106 Timer2 Register 0000 TMR3HLD 0108 Timer3 Holding Register (for 32-bit timer operations only) xxxx TMR3 010A Timer3 Register 0000 PR2 010C Period Register 2 FFFF PR3 010E T2CON 0110 TON -- TSIDL -- -- -- -- -- -- TGATE TCKPS<1:0> T32 -- TCS -- 0000 T3CON 0112 TON -- TSIDL -- -- -- -- -- -- TGATE TCKPS<1:0> -- -- TCS -- 0000 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. Bit 0 All Resets TABLE 4-13: SFR Name SFR Addr IC1BUF 0140 IC1CON 0142 Legend: TON Bit 6 -- TSIDL -- -- -- -- -- -- TGATE TCKPS<1:0> -- TSYNC TCS -- Period Register 3 0000 FFFF INPUT CAPTURE REGISTER MAP FOR dsPIC33FJ06GS202 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 -- -- ICSIDL -- -- -- -- Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 ICOV ICBNE Bit 2 Bit 1 Input Capture 1 Register -- ICTMR x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. xxxx ICI<1:0> ICM<2:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 56 TABLE 4-11: SFR Name SFR Addr INPUT CAPTURE REGISTER MAP FOR dsPIC33FJ16GSX02 AND dsPIC33FJ16GSX04 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 -- -- ICSIDL -- -- -- -- Bit 8 Bit 7 IC1BUF 0140 IC1CON 0142 IC2BUF 0144 IC2CON 0146 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-15: SFR Name SFR Addr Bit 6 Bit 4 Bit 3 -- ICI<1:0> ICOV ICBNE ICM<2:0> ICI<1:0> ICOV ICBNE ICM<2:0> Bit 0 -- -- ICSIDL -- -- -- -- -- All Resets 0000 Input Capture 2 Register xxxx ICTMR 0000 OUTPUT COMPARE REGISTER MAP FOR dsPIC33FJ06GS101 AND dsPIC33FJ06GSX02 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 0180 Output Compare 1 Secondary Register 0182 Output Compare 1 Register OC1CON 0184 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. SFR Addr Bit 1 xxxx ICTMR OC1R SFR Name Bit 2 Input Capture 1 Register OC1RS TABLE 4-16: Bit 5 -- -- OCSIDL -- -- -- -- -- Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets xxxx xxxx -- -- -- OCFLT OCTSEL OCM<2:0> 0000 OUTPUT COMPARE REGISTER MAP FOR dsPIC33FJ16GSX02 AND dsPIC33FJ06GSX04 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets OC1RS 0180 Output Compare 1 Secondary Register OC1R 0182 Output Compare 1 Register OC1CON 0184 OC2RS 0186 Output Compare 2 Secondary Register xxxx OC2R 0188 Output Compare 2 Register xxxxx OC2CON 018A Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-17: -- -- -- -- OCSIDL OCSIDL -- -- -- -- -- -- -- -- -- xxxx -- -- xxxx -- -- -- -- -- Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 PTCON 0400 PTEN -- PTSIDL SESTAT SEIEN EIPU SYNCPOL SYNCOEN SYNCEN -- PTCON2 0402 -- -- -- -- -- -- -- -- -- -- PTPER 0404 SEVTCMP 0406 DS70318F-page 57 MDC Legend: 040A OCFLT OCTSEL OCM<2:0> OCTSEL 0000 OCM<2:0> 0000 HIGH-SPEED PWM REGISTER MAP Addr Offset File Name OCFLT Bit 5 Bit 4 Bit 3 SYNCSRC<1:0> -- -- Bit 2 Bit 1 Bit 0 SEVTPS<3:0> -- 0000 PCLKDIV<2:0> 0000 PTPER<15:0> SEVTCMP<15:3> FFF8 -- MDC<15:0> x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. All Resets -- -- 0000 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-14: HIGH-SPEED PWM GENERATOR 1 REGISTER MAP File Name Addr Offset Bit 15 PWMCON1 0420 FLTSTAT IOCON1 0422 PENH FCLCON1 0424 IFLTMOD PDC1 0426 PDC1<15:0> PHASE1 0428 PHASE1<15:0> DTR1 042A -- -- -- -- Bit 14 Bit 13 CLSTAT TRGSTAT PENL POLH Bit 12 Bit 11 Bit 10 FLTIEN CLIEN TRGIEN POLL PMOD<1:0> CLSRC<4:0> Bit 9 Bit 8 Bit 7 Bit 6 ITB MDCS DTC<1:0> OVRENH OVRENL OVRDAT<1:0> CLPOL CLMOD Bit 5 Bit 4 -- -- FLTDAT<1:0> All Resets XPRES IUE 0000 SWAP OSYNC 0000 Bit 2 Bit 1 -- CAM CLDAT<1:0> FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000 0000 0000 DTR1<13:0> 0000 ALTDTR1<13:0> 0000 ALTDTR1 042C SDC1 042E SDC1<15:0> SPHASE1 0430 SPHASE1<15:0> TRIG1 0432 0000 0000 TRGCMP<15:3> -- -- -- 0000 TRGCON1 0434 STRIG1 0436 STRGCMP<15:3> -- -- -- 0000 PWMCAP1 0438 PWMCAP1<15:3> -- -- -- 0000 LEBCON1 043A -- -- -- 0000 Legend: TRGDIV<3:0> Bit 0 Bit 3 PHR PHF PLR -- PLF FLTLEBEN -- -- -- DTM CLLEBEN -- TRGSTRT<5:0> LEB<6:0> 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-19: HIGH-SPEED PWM GENERATOR 2 REGISTER MAP FOR dsPIC33FJ06GS102/202 AND dsPIC33FJ16GSX02/X04 DEVICES ONLY (c) 2008-2012 Microchip Technology Inc. File Name Addr Offset Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 PWMCON2 0440 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN IOCON2 0442 PENH PENL POLH POLL FCLCON2 0444 IFLTMOD PDC2 0446 PDC2<15:0> PHASE2 0448 PHASE2<15:0> DTR2 044A -- -- -- -- PMOD<1:0> CLSRC<4:0> Bit 9 Bit 8 Bit 7 Bit 6 ITB MDCS DTC<1:0> OVRENH OVRENL OVRDAT<1:0> CLPOL CLMOD FLTSRC<4:0> XPRES IUE 0000 SWAP OSYNC 0000 Bit 1 -- CAM CLDAT<1:0> FLTPOL FLTMOD<1:0> 0000 0000 0000 0000 044E SDC2<15:0> SPHASE2 0450 SPHASE2<15:0> TRIG2 0452 0000 0000 -- TRGCMP<15:3> -- -- All Resets Bit 2 ALTDTR2<13:0> 044C -- -- FLTDAT<1:0> Bit 0 Bit 3 0000 ALTDTR2 -- Bit 4 DTR2<13:0> SDC2 -- DTM -- -- -- TRGSTRT<5:0> 0000 TRGCON2 0454 STRIG2 0456 STRGCMP<15:3> -- -- -- 0000 PWMCAP2 0458 PWMCAP2<15:3> -- -- -- 0000 LEBCON2 045A -- -- -- 0000 Legend: TRGDIV<3:0> Bit 5 PHR PHF PLR PLF FLTLEBEN CLLEBEN x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. LEB<6:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 58 TABLE 4-18: HIGH-SPEED PWM GENERATOR 3 REGISTER MAP FOR dsPIC33FJ16GSX02/X04 DEVICES ONLY File Name Addr Offset Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 PWMCON3 0460 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN IOCON3 0462 PENH PENL POLH POLL FCLCON3 0464 IFLTMOD PDC3 0466 PDC3<15:0> PHASE3 0468 PHASE3<15:0> DTR3 046C -- -- -- -- PMOD<1:0> CLSRC<4:0> Bit 9 Bit 8 Bit 7 Bit 6 ITB MDCS DTC<1:0> OVRENH OVRENL OVRDAT<1:0> CLPOL CLMOD Bit 5 Bit 4 -- -- FLTDAT<1:0> All Resets XPRES IUE 0000 SWAP OSYNC 0000 Bit 2 Bit 1 -- CAM CLDAT<1:0> FLTSRC<4:0> FLTPOL FLTMOD<1:0> 0000 0000 0000 DTR3<13:0> 0000 ALTDTR3<13:0> 0000 ALTDTR3 046C SDC3 046E SDC3<15:0> SPHASE3 0470 SPHASE3<15:0> TRIG3 0472 0000 0000 TRGCMP<15:3> -- -- -- 0000 TRGCON3 0474 STRIG3 0476 STRGCMP<15:3> -- -- -- 0000 PWMCAP3 0478 PWMCAP3<15:3> -- -- -- 0000 LEBCON3 047A -- -- -- 0000 Legend: TRGDIV<3:0> Bit 0 Bit 3 PHR PHF PLR -- PLF FLTLEBEN -- -- -- DTM CLLEBEN -- TRGSTRT<5:0> LEB<6:0> 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-21: HIGH-SPEED PWM GENERATOR 4 REGISTER MAP FOR dsPIC33FJ06GS101 AND dsPIC33FJ16GS50X DEVICES ONLY File Name Addr Offset Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 PWMCON4 0480 FLTSTAT CLSTAT TRGSTAT FLTIEN CLIEN TRGIEN IOCON4 0482 PENH PENL POLH POLL FCLCON4 0484 IFLTMOD PDC4 0486 PDC4<15:0> PHASE4 0488 PHASE4<15:0> DTR4 048A -- -- -- -- PMOD<1:0> CLSRC<4:0> Bit 9 Bit 8 Bit 7 Bit 6 ITB MDCS DTC<1:0> OVRENH OVRENL OVRDAT<1:0> CLPOL CLMOD Bit 4 -- -- FLTDAT<1:0> FLTSRC<4:0> Bit 0 All Resets XPRES IUE 0000 SWAP OSYNC 0000 Bit 3 Bit 2 Bit 1 -- CAM CLDAT<1:0> FLTPOL FLTMOD<1:0> 0000 0000 0000 DTR4<13:0> 0000 ALTDTR4<13:0> 0000 ALTDTR4 048A SDC4 048E SDC4<15:0> SPHASE4 0490 SPHASE4<15:0> TRIG4 0492 0000 0000 TRGCMP<15:3> -- -- -- 0000 DS70318F-page 59 TRGCON4 0494 STRIG4 0496 STRGCMP<15:3> -- -- -- 0000 PWMCAP4 0498 PWMCAP4<15:3> -- -- -- 0000 LEBCON4 049A -- -- -- 0000 Legend: TRGDIV<3:0> Bit 5 PHR PHF PLR -- PLF FLTLEBEN -- -- -- CLLEBEN x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. DTM -- LEB<6:0> TRGSTRT<5:0> 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-20: I2C1 REGISTER MAP SFR Name SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets I2C1RCV 0200 -- -- -- -- -- -- -- -- Receive Register 0000 I2C1TRN 0202 -- -- -- -- -- -- -- -- Transmit Register 00FF I2C1BRG 0204 -- -- -- -- -- -- -- I2C1CON 0206 I2CEN -- IPMIEN A10M DISSLW SMEN GCEN STREN GCSTAT ADD10 IWCOL I2COV 0000 ACKDT ACKEN RCEN PEN RSEN SEN D_A P S R_W RBF TBF 1000 I2C1STAT 0208 -- -- -- BCL I2C1ADD 020A -- -- -- -- -- -- Address Register 0000 I2C1MSK 020C -- -- -- -- -- -- AMSK<9:0> 0000 Legend: ACKSTAT TRSTAT I2CSIDL SCLREL Baud Rate Generator Register x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-23: SFR Name SFR Addr U1MODE 0220 U1STA 0222 UART1 REGISTER MAP Bit 15 Bit 14 Bit 13 Bit 12 UARTEN -- USIDL IREN RTSMD -- -- UTXBRK UTXE N UTXISEL1 UTXINV UTXISEL0 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 UEN1 UEN0 WAKE LPBACK UTXBF TRMT URXISEL<1:0> Bit 5 Bit 4 Bit 3 ABAUD URXINV BRGH ADDEN RIDLE PERR U1TXREG 0224 -- -- -- -- -- -- -- UART Transmit Register U1RXREG 0226 -- -- -- -- -- -- -- UART Receive Register U1BRG 0228 Legend: 0000 Bit 2 Bit 1 PDSEL<1:0> FERR OERR Bit 0 All Resets STSEL 0000 URXDA 0110 xxxx 0000 Baud Rate Generator Prescaler 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-24: SPI1 REGISTER MAP (c) 2008-2012 Microchip Technology Inc. SFR Name SFR Addr Bit 15 Bit 14 Bit 13 SPI1STAT 0240 SPIEN -- SPISIDL SPI1CON1 0242 -- -- -- SPI1CON2 0244 FRMEN SPIFSD FRMPOL Bit 12 Bit 11 -- -- DISSCK DISSDO -- -- Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 -- -- -- -- -- SPIROV -- MODE16 SMP CKE SSEN CKP MSTEN -- -- -- -- -- -- SPI1BUF 0248 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. SPI1 Transmit and Receive Buffer Register Bit 3 Bit 2 Bit 1 Bit 0 All Resets -- -- SPITBF SPIRBF 0000 SPRE<2:0> -- -- PPRE<1:0> -- FRMDLY -- 0000 0000 0000 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 60 TABLE 4-22: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ06GS101 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 ADCON 0300 ADON -- ADSIDL SLOWCLK -- GSWTRG -- FORM ADPCFG 0302 -- -- -- -- -- -- -- -- ADSTAT 0306 -- -- -- -- -- -- -- ADBASE 0308 ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC1<4:0> IRQEN0 PEND0 SWTRG0 ADCPC1 030C IRQEN3 PEND3 SWTRG3 TRGSRC3<4:0> -- -- -- ADCBUF0 0320 ADC Data Buffer 0 xxxx ADCBUF1 0322 ADC Data Buffer 1 xxxx ADCBUF2 0324 ADC Data Buffer 2 xxxx ADCBUF3 0326 ADC Data Buffer 3 xxxx ADCBUF6 032C ADC Data Buffer 6 xxxx ADCBUF7 032E ADC Data Buffer 7 xxxx Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. SFR Name TABLE 4-26: -- Bit 7 EIE PCFG7 -- Bit 6 ORDER Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SEQSAMP ASYNCSAMP -- PCFG6 -- -- PCFG3 PCFG2 ADCS<2:0> PCFG1 PCFG0 -- -- -- P3RDY -- P1RDY P0RDY ADBASE<15:1> 0003 -- -- 0000 0000 -- 0000 0000 -- HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ06GS102 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 ADCON 0300 ADON -- ADSIDL SLOWCLK -- GSWTRG -- FORM EIE ORDER ADPCFG 0302 -- -- -- -- -- -- -- -- -- -- PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 ADSTAT 0306 -- -- -- -- -- -- -- -- -- -- -- -- -- P2RDY P1RDY P0RDY ADBASE 0308 SFR Name 0000 -- TRGSRC0<4:0> -- All Resets Bit 5 Bit 4 SEQSAMP ASYNCSAMP Bit 3 -- Bit 2 Bit 1 ADCS<2:0> ADBASE<15:1> TRGSRC1<4:0> Bit 0 All Resets 0003 -- 0000 0000 0000 ADCPC0 030A IRQEN1 PEND1 SWTRG1 ADCPC1 030C -- -- -- ADCBUF0 0320 ADC Data Buffer 0 xxxx ADCBUF1 0322 ADC Data Buffer 1 xxxx ADCBUF2 0324 ADC Data Buffer 2 xxxx ADCBUF3 0326 ADC Data Buffer 3 xxxx ADCBUF4 0328 ADC Data Buffer 4 xxxx ADCBUF5 032A ADC Data Buffer 5 xxxx Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- -- -- -- -- IRQEN0 PEND0 SWTRG0 TRGSRC0<4:0> 0000 IRQEN2 PEND2 SWTRG2 TRGSRC2<4:0> 0000 DS70318F-page 61 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-25: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ06GS202 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 ADCON 0300 ADON -- ADSIDL SLOWCLK -- GSWTRG -- FORM EIE ORDER ADPCFG 0302 -- -- -- -- -- -- -- -- -- -- PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 ADSTAT 0306 -- -- -- -- -- -- -- -- -- P6RDY -- -- -- P2RDY P1RDY P0RDY ADBASE 0308 SFR Name Bit 5 Bit 4 SEQSAMP ASYNCSAMP Bit 3 Bit 2 Bit 1 -- ADCS<2:0> ADBASE<15:1> All Resets 0003 -- 0000 0000 0000 ADCPC0 030A IRQEN1 PEND1 SWTRG1 IRQEN0 PEND0 SWTRG0 TRGSRC0<4:0> 0000 ADCPC1 030C -- -- -- -- -- -- -- -- IRQEN2 PEND2 SWTRG2 TRGSRC2<4:0> 0000 ADCPC3 0310 -- -- -- -- -- -- -- -- IRQEN6 PEND6 SWTRG6 TRGSRC6<4:0> 0000 ADCBUF0 0320 ADC Data Buffer 0 xxxx ADCBUF1 0322 ADC Data Buffer 1 xxxx ADCBUF2 0324 ADC Data Buffer 2 xxxx ADCBUF3 0326 ADC Data Buffer 3 xxxx ADCBUF4 0328 ADC Data Buffer 4 xxxx ADCBUF5 032A ADC Data Buffer 5 xxxx ADCBUF12 0338 ADC Data Buffer 12 xxxx ADCBUF13 033A ADC Data Buffer13 xxxx Legend: TRGSRC1<4:0> Bit 0 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-28: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ16GS402/404 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 ADCON 0300 ADON -- ADSIDL SLOWCLK -- GSWTRG -- ADPCFG 0302 -- -- -- -- -- -- -- ADSTAT 0306 -- -- -- -- -- -- -- ADBASE 0308 SFR Name Bit 7 Bit 6 Bit 5 Bit 4 FORM EIE ORDER -- PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 -- -- -- -- -- P3RDY P2RDY P1RDY P0RDY SEQSAMP ASYNCSAMP Bit 3 -- Bit 2 Bit 1 Bit 0 ADCS<2:0> ADBASE<15:1> All Resets 0003 -- 0000 0000 0000 (c) 2008-2012 Microchip Technology Inc. ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC1<4:0> IRQEN0 PEND0 SWTRG0 TRGSRC0<4:0> 0000 ADCPC1 030C IRQEN3 PEND3 SWTRG3 TRGSRC3<4:0> IRQEN2 PEND2 SWTRG2 TRGSRC2<4:0> 0000 ADCBUF0 0320 ADC Data Buffer 0 xxxx ADCBUF1 0322 ADC Data Buffer 1 xxxx ADCBUF2 0324 ADC Data Buffer 2 xxxx ADCBUF3 0326 ADC Data Buffer 3 xxxx ADCBUF4 0328 ADC Data Buffer 4 xxxx ADCBUF5 032A ADC Data Buffer 5 xxxx ADCBUF6 032C ADC Data Buffer 6 xxxx ADCBUF7 032E ADC Data Buffer 7 xxxx Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 62 TABLE 4-27: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ16GS502 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 ADCON 0300 ADON -- ADSIDL SLOWCLK -- GSWTRG -- ADPCFG 0302 -- -- -- -- -- -- -- ADSTAT 0306 -- -- -- -- -- -- -- ADBASE 0308 SFR Name Bit 7 Bit 6 Bit 5 Bit 4 FORM EIE ORDER -- PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 -- -- P6RDY -- -- P3RDY P2RDY P1RDY P0RDY SEQSAMP ASYNCSAMP Bit 3 -- Bit 2 Bit 1 Bit 0 ADCS<2:0> ADBASE<15:1> All Resets 0003 -- 0000 0000 0000 ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC1<4:0> IRQEN0 PEND0 SWTRG0 TRGSRC0<4:0> ADCPC1 030C IRQEN3 PEND3 SWTRG3 TRGSRC3<4:0> IRQEN2 PEND2 SWTRG2 TRGSRC2<4:0> 0000 ADCPC3 0310 -- -- IRQEN6 PEND6 SWTRG6 TRGSRC6<4:0> 0000 ADCBUF0 0320 ADC Data Buffer 0 xxxx ADCBUF1 0322 ADC Data Buffer 1 xxxx ADCBUF2 0324 ADC Data Buffer 2 xxxx ADCBUF3 0326 ADC Data Buffer 3 xxxx ADCBUF4 0328 ADC Data Buffer 4 xxxx ADCBUF5 032A ADC Data Buffer 5 xxxx ADCBUF6 032C ADC Data Buffer 6 xxxx ADCBUF7 032E ADC Data Buffer 7 xxxx ADCBUF12 0338 ADC Data Buffer 12 xxxx ADCBUF13 033A ADC Data Buffer 13 xxxx Legend: -- -- -- -- -- -- x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. 0000 DS70318F-page 63 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-29: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ16GS504 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 ADCON 0300 ADON -- ADSIDL ADPCFG 0302 -- -- -- ADSTAT 0306 -- -- -- SFR Name Bit 11 Bit 10 SLOWCLK -- GSWTRG -- PCFG11 PCFG10 -- -- -- Bit 9 Bit 8 -- FORM PCFG9 PCFG8 -- -- Bit 7 Bit 6 Bit 5 Bit 4 SEQSAMP ASYNCSAMP Bit 3 -- Bit 2 Bit 1 Bit 0 ADCS<2:0> All Resets EIE ORDER PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 0000 -- P6RDY P5RDY P4RDY P3RDY P2RDY P1RDY P0RDY 0000 ADBASE 0308 ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC1<4:0> IRQEN0 PEND0 SWTRG0 TRGSRC0<4:0> 0000 ADCPC1 030C IRQEN3 PEND3 SWTRG3 TRGSRC3<4:0> IRQEN2 PEND2 SWTRG2 TRGSRC2<4:0> 0000 ADCPC2 030E IRQEN5 PEND5 SWTRG5 TRGSRC5<4:0> IRQEN4 PEND4 SWTRG4 TRGSRC4<4:0> 0000 ADCPC3 0310 -- -- -- IRQEN6 PEND6 SWTRG6 TRGSRC6<4:0> 0000 ADCBUF0 0320 ADC Data Buffer 0 xxxx ADCBUF1 0322 ADC Data Buffer 1 xxxx ADCBUF2 0324 ADC Data Buffer 2 xxxx ADCBUF3 0326 ADC Data Buffer 3 xxxx ADCBUF4 0328 ADC Data Buffer 4 xxxx ADCBUF5 032A ADC Data Buffer 5 xxxx ADCBUF6 032C ADC Data Buffer 6 xxxx ADCBUF7 032E ADC Data Buffer 7 xxxx ADCBUF8 0330 ADC Data Buffer 8 xxxx ADCBUF9 0332 ADC Data Buffer 9 xxxx ADCBUF10 0334 ADC Data Buffer 10 xxxx ADCBUF11 0336 ADC Data Buffer 11 xxxx ADCBUF12 0338 ADC Data Buffer 12 xxxx ADCBUF13 033A ADC Data Buffer 13 xxxx Legend: ADBASE<15:1> 0003 -- -- -- -- -- x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. -- 0000 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 64 TABLE 4-30: File Name ANALOG COMPARATOR CONTROL REGISTER MAP FOR dsPIC33FJ06GS202 DEVICES ONLY ADR Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 CMPCON1 0540 CMPON -- CMPSIDL -- -- -- -- DACOE CMPDAC1 0542 -- -- -- -- -- -- CMPCON2 0544 CMPON -- CMPSIDL -- -- -- CMPDAC2 0546 -- -- -- -- -- -- TABLE 4-32: Bit 7 Bit 6 INSEL<1:0> Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 EXTREF -- CMPSTAT -- CMPPOL RANGE CMREF<9:0> -- DACOE INSEL<1:0> EXTREF -- All Resets 0000 0000 CMPSTAT -- CMPPOL RANGE CMREF<9:0> 0000 0000 ANALOG COMPARATOR CONTROL REGISTER MAP dsPIC33FJ16GS502/504 DEVICES ONLY File Name ADR Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 CMPCON1 0540 CMPON -- CMPSIDL -- -- -- -- DACOE CMPDAC1 0542 -- -- -- -- -- -- CMPCON2 0544 CMPON -- CMPSIDL -- -- -- CMPDAC2 0546 -- -- -- -- -- -- CMPCON3 0548 CMPON -- CMPSIDL -- -- -- CMPDAC3 054A -- -- -- -- -- -- CMPCON4 054C CMPON -- CMPSIDL -- -- -- CMPDAC4 054E -- -- -- -- -- -- Bit 7 Bit 6 INSEL<1:0> Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 EXTREF -- CMPSTAT -- CMPPOL RANGE CMREF<9:0> -- DACOE INSEL<1:0> EXTREF -- DACOE INSEL<1:0> EXTREF -- CMPSTAT -- CMPPOL RANGE DACOE INSEL<1:0> EXTREF -- CMREF<9:0> 0000 0000 CMPSTAT -- CMPPOL RANGE CMREF<9:0> -- 0000 0000 CMREF<9:0> -- All Resets 0000 0000 CMPSTAT -- CMPPOL RANGE 0000 0000 DS70318F-page 65 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-31: PERIPHERAL PIN SELECT INPUT REGISTER MAP SFR Name SFR Addr Bit 15 Bit 14 RPINR0 0680 -- -- RPINR1 0682 -- -- RPINR2 0684 -- -- RPINR3 0686 -- RPINR7 068E -- RPINR11 0696 -- -- RPINR18 06A4 -- -- RPINR20 06A8 -- -- RPINR21 06AA -- -- RPINR29 06BA -- -- RPINR30 06BC -- RPINR31 06BE -- RPINR32 06C0 RPINR33 RPINR34 Legend: Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets -- -- -- -- -- -- -- -- 3F00 -- -- T1CKR<5:0> -- -- -- -- 0000 -- T3CKR<5:0> -- -- T2CKR<5:0> 3F3F -- IC2R<5:0> -- -- IC1R<5:0> 3F3F -- -- OCFAR<5:0> 3F3F U1CTSR<5:0> -- -- U1RXR<5:0> 003F SCK1R<5:0> -- -- SDI1R<5:0> 3F3F -- -- SS1R<5:0> FLT1R<5:0> -- -- -- FLT3R<5:0> -- -- FLT2R<5:0> 3F3F -- FLT5R<5:0> -- -- FLT4R<5:0> 3F3F -- -- FLT7R<5:0> -- -- FLT6R<5:0> 3F3F 06C2 -- -- SYNCI1R<5:0> -- -- FLT8R<5:0> 3F3F 06C4 -- -- -- -- SYNCI2R<5:0> 3F3F -- -- Bit 11 Bit 10 Bit 9 Bit 8 -- -- INT1R<5:0> -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- INT2R<5:0> -- -- -- -- -- -- -- -- 003F 0000 -- -- 3F00 PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33FJ06GS101 (c) 2008-2012 Microchip Technology Inc. Addr Bit 15 Bit 14 RPOR0 06D0 -- -- RPOR1 06D2 -- -- RPOR2 06D4 -- RPOR3 06D6 -- RPOR16 06F0 RPOR17 06F2 Legend: Bit 12 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-34: File Name Bit 13 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 6 RP1R<5:0> -- -- RP0R<5:0> 0000 RP3R<5:0> -- -- RP2R<5:0> 0000 -- RP5R<5:0> -- -- RP4R<5:0> 0000 -- RP7R<5:0> -- -- RP6R<5:0> 0000 -- -- RP33<5:0> -- -- RP32<5:0> 0000 -- -- RP35<5:0> -- -- RP34<5:0> 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets Bit 7 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 66 TABLE 4-33: File Name PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33FJ06GS102, dsPIC33FJ06GS202, dsPIC33FJ16GS402 AND dsPIC33FJ16GS502 Addr Bit 15 Bit 14 RPOR0 06D0 -- -- RPOR1 06D2 -- -- RPOR2 06D4 -- RPOR3 06D6 -- RPOR4 06D8 RPOR5 Bit 6 RP1R<5:0> -- -- RP0R<5:0> 0000 RP3R<5:0> -- -- RP2R<5:0> 0000 -- RP5R<5:0> -- -- RP4R<5:0> 0000 -- RP7R<5:0> -- -- RP6R<5:0> 0000 -- -- RP9R<5:0> -- -- RP8R<5:0> 0000 06DA -- -- RP11R<5:0> -- -- RP10R<5:0> 0000 RPOR6 06DC -- -- RP13R<5:0> -- -- RP12R<5:0> 0000 RPOR7 06DE -- -- RP15R<5:0> -- -- RP14R<5:0> 0000 RPOR16 06F0 -- -- RP33<5:0> -- -- RP32<5:0> 0000 RPOR17 06F2 -- -- RP35<5:0> -- -- RP34<5:0> 0000 Bit 11 Bit 10 Bit 9 Bit 8 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-36: File Name Bit 12 All Resets Bit 7 Legend: Bit 13 PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33FJ16GS404 AND dsPIC33FJ16GS504 Addr Bit 15 Bit 14 RPOR0 06D0 -- -- RPOR1 06D2 -- -- RPOR2 06D4 -- RPOR3 06D6 -- RPOR4 06D8 RPOR5 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets DS70318F-page 67 Bit 7 Bit 6 RP1R<5:0> -- -- RP0R<5:0> 0000 RP3R<5:0> -- -- RP2R<5:0> 0000 -- RP5R<5:0> -- -- RP4R<5:0> 0000 -- RP7R<5:0> -- -- RP6R<5:0> 0000 -- -- RP9R<5:0> -- -- RP8R<5:0> 0000 06DA -- -- RP11R<5:0> -- -- RP10R<5:0> 0000 RPOR6 06DC -- -- RP13R<5:0> -- -- RP12R<5:0> 0000 RPOR7 06DE -- -- RP15R<5:0> -- -- RP14R<5:0> 0000 RPOR8 06E0 -- -- RP17R<5:0> -- -- RP16R<5:0> 0000 RPOR9 06E2 -- -- RP19R<5:0> -- -- RP18R<5:0> 0000 RPOR10 06E4 -- -- RP21R<5:0> -- -- RP20R<5:0> 0000 RPOR11 06E6 -- -- RP23R<5:0> -- -- RP22R<5:0> 0000 RPOR12 06E8 -- -- RP25R<5:0> -- -- RP24R<5:0> 0000 RPOR13 06EA -- -- RP27R<5:0> -- -- RP26R<5:0> 0000 RPOR14 06EC -- -- RP29R<5:0> -- -- RP28R<5:0> 0000 RPOR16 06F0 -- -- RP33<5:0> -- -- RP32<5:0> 0000 RPOR17 06F2 -- -- RP35<5:0> -- -- RP34<5:0> 0000 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-35: SFR Name PORTA REGISTER MAP SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets TRISA 02C0 -- -- -- -- -- -- -- -- -- -- -- TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 001F PORTA 02C2 -- -- -- -- -- -- -- -- -- -- -- RA4 RA3 RA2 RA1 RA0 xxxx LATA 02C4 -- -- -- -- -- -- -- -- -- -- -- LATA4 LATA3 LATA2 LATA1 LATA0 0000 ODCA 02C6 -- -- -- -- -- -- -- -- -- -- -- ODCA4 ODCA3 -- -- -- 0000 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-38: SFR Name PORTB REGISTER MAP FOR dsPIC33FJ06GS101 SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets TRISB 02C8 -- -- -- -- -- -- -- -- TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 00FF PORTB 02CA -- -- -- -- -- -- -- -- RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx LATB 02CC -- -- -- -- -- -- -- -- LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 0000 ODCB 02CE -- -- -- -- -- -- -- -- ODCB7 ODCB6 -- ODCB4 -- -- -- -- 0000 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-39: SFR Name PORTB REGISTER MAP FOR dsPIC33FJ06GS102, dsPIC33FJ06GS202, dsPIC33FJ16GS402, dsPIC33FJ16GS404, dsPIC33FJ16GS502 AND dsPIC33FJ16GS504 (c) 2008-2012 Microchip Technology Inc. SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets TRISB 02C8 TRISB15 TRISB14 TRISB13 TRISB12 TRISB11 TRISB10 TRISB9 TRISB8 TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 FFFF PORTB 02CA RB15 RB14 RB13 RB12 RB11 RB10 RB9 RB8 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx LATB 02CC LATB15 LATB14 LATB13 LATB12 LATB11 LATB10 LATB9 LATB8 LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 0000 ODCB 02CE ODCB15 ODCB14 ODCB13 ODCB12 ODCB11 -- -- ODCB8 ODCB7 ODCB6 -- ODCB4(1) -- -- -- -- 0000 Bit 3 Bit 2 Bit 1 Bit 0 All Resets Legend: Note 1: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. This bit is not available on dsPIC33FJ06GS202/502 devices. TABLE 4-40: SFR Name PORTC REGISTER MAP FOR dsPIC33FJ16GS404 AND dsPIC33FJ16GS504 SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 TRISC 02D0 -- -- TRISC13 TRISC12 TRISC11 TRISC10 TRISC9 TRISC8 TRISC7 TRISC6 TRISC3 TRISC2 TRISC1 TRISC0 3FFF PORTC 02D2 -- -- RC13 RC12 RC11 RC10 RC9 RC8 RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 xxxx LATC 02D4 -- -- LATC13 LATC12 LATC11 LATC10 LATC9 LATC8 LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0 0000 ODCC 02D6 -- -- ODCC13 ODCC12 ODCC11 -- -- ODCC8 ODCC7 ODCC6 ODCC5 ODCC4 ODCC3 -- -- ODCC0 0000 Legend: x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TRISC5 Bit 4 TRISC4 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 68 TABLE 4-37: SYSTEM CONTROL REGISTER MAP SFR Name SFR Addr Bit 15 Bit 14 IOPUWR RCON 0740 TRAPR OSCCON 0742 -- Bit 13 Bit 12 Bit 11 Bit 10 -- -- -- -- COSC<2:0> -- CLKDIV 0744 ROI PLLFBD 0746 -- -- -- -- REFOCON 074E ROON -- ROSSLP ROSEL OSCTUN 0748 -- -- -- -- -- 0750 ENAPLL APLLCK SELACLK -- -- ACLKCON Legend: Note 1: 2: Bit 8 CM VREGS NOSC<2:0> DOZEN FRCDIV<2:0> -- -- Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 EXTR SWR SWDTEN WDTO SLEEP IDLE BOR POR xxxx(1) CLKLOCK IOLOCK LOCK -- CF -- -- OSWEN 0300(2) PLLPOST<1:0> -- PLLPRE<4:0> -- -- -- APSTSCLR<2:0> -- -- -- -- ASRCSEL FRCSEL -- -- -- -- Bit 4 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 NVMCON 0760 WR WREN WRERR -- -- -- -- -- -- ERASE -- NVMKEY 0766 -- -- -- -- -- -- -- -- -- 0000 0000 -- -- -- Bit 3 Bit 2 Bit 1 -- -- Bit 0 2300 All Resets 0000(1) NVMOP<3:0> NVMKEY<7:0> 0000 PMD REGISTER MAP FOR dsPIC33FJ06GS101 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 PMD1 0770 -- -- -- T2MD T1MD -- PWMMD -- PMD2 0772 -- -- -- -- -- -- IC2MD IC1MD PMD3 0774 -- -- -- -- -- CMPMD -- PMD4 0776 -- -- -- -- -- -- PMD6 077A -- -- -- -- PWM4MD -- Bit 8 Bit 7 DS70318F-page 69 Bit 1 Bit 0 All Resets -- -- ADCMD 0000 -- OC2MD OC1MD 0000 -- -- -- -- 0000 -- REFOMD -- -- -- 0000 -- -- -- -- -- 0000 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 Bit 6 Bit 5 Bit 4 Bit 3 I2C1MD -- U1MD -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PWM1MD -- -- -- Bit 6 SPI1MD Bit 2 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-44: SFR Name -- x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. Reset value shown is for POR only. Value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset. TABLE 4-43: Legend: -- NVM REGISTER MAP Bit 15 SFR Name 0030 -- TUN<5:0> Addr Legend: Note 1: 3040 PLLDIV<8:0> RODIV<3:0> -- Bit 0 All Resets Bit 6 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. The RCON register Reset values are dependent on type of Reset. The OSCCON register Reset values are dependent on the FOSC Configuration bits and on type of Reset. TABLE 4-42: File Name DOZE<2:0> Bit 9 PMD REGISTER MAP FOR dsPIC33FJ06GS102 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 PMD1 0770 -- -- -- T2MD T1MD -- PWMMD -- I2C1MD -- U1MD -- -- -- ADCMD PMD2 0772 -- -- -- -- -- -- IC2MD IC1MD -- -- -- -- -- -- OC2MD OC1MD 0000 PMD3 0774 -- -- -- -- -- CMPMD -- -- -- -- -- -- -- -- -- -- 0000 PMD4 0776 -- -- -- -- -- -- -- -- -- -- -- -- REFOMD -- -- -- 0000 PMD6 077A -- -- -- -- -- -- PWM2MD PWM1MD -- -- -- -- -- -- -- -- 0000 Legend: Bit 8 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. Bit 7 SPI1MD dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. TABLE 4-41: SFR Name PMD REGISTER MAP FOR dsPIC33FJ06GS202 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 PMD1 0770 -- -- -- T2MD T1MD -- PMD2 0772 -- -- -- -- -- -- PMD3 0774 -- -- -- -- -- CMPMD PMD4 0776 -- -- -- -- -- -- PMD6 077A -- -- -- -- -- -- PMD7 077C -- -- -- -- -- -- CMP2MD Legend: -- -- ADCMD 0000 -- -- OC1MD 0000 -- -- -- -- 0000 -- REFOMD -- -- -- 0000 -- -- -- -- -- 0000 -- -- -- -- -- 0000 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 Bit 4 PWMMD -- I2C1MD -- U1MD -- -- IC1MD -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PWM2MD PWM1MD -- -- -- CMP1MD -- -- -- Bit 3 SPI1MD PMD REGISTER MAP FOR dsPIC33FJ16GS402 AND dsPIC33FJ16GS404 DEVICES ONLY Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 PMD1 0770 -- -- T3MD T2MD T1MD -- PMD2 0772 -- -- -- -- -- -- PMD3 0774 -- -- -- -- -- -- PMD4 0776 -- -- -- -- -- -- PMD6 077A -- -- -- -- -- PWM3MD PMD7 077C -- -- -- -- -- -- -- (c) 2008-2012 Microchip Technology Inc. Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 PWMMD -- I2C1MD -- U1MD -- -- -- ADCMD IC2MD IC1MD -- -- -- -- -- -- OC2MD OC1MD 0000 -- -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- REFOMD -- -- -- 0000 PWM2MD PWM1MD -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- -- -- -- 0000 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 SPI1MD x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-47: PMD REGISTER MAP FOR dsPIC33FJ16GS502 AND dsPIC33FJ16GS504 DEVICES ONLY SFR Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 PMD1 0770 -- -- T3MD T2MD T1MD -- PMD2 0772 -- -- -- -- -- -- PMD3 0774 -- -- -- -- -- CMPMD PMD4 0776 -- -- -- -- -- -- PMD6 077A -- -- -- -- PWM4MD PWM3MD PMD7 077C -- -- -- -- CMP4MD CMP3MD CMP2MD Legend: All Resets Bit 5 Bit 15 SFR Name Bit 0 Bit 6 SFR Addr Legend: Bit 1 Bit 7 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. TABLE 4-46: SFR Name Bit 2 Bit 8 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 PWMMD -- I2C1MD -- U1MD -- -- -- ADCMD IC2MD IC1MD -- -- -- -- -- -- OC2MD OC1MD 0000 -- -- -- -- -- -- -- -- -- -- 0000 -- -- -- -- -- -- REFOMD -- -- -- 0000 PWM2MD PWM1MD -- -- -- -- -- -- -- -- 0000 CMP1MD -- -- -- -- -- -- -- -- 0000 x = unknown value on Reset, -- = unimplemented, read as `0'. Reset values are shown in hexadecimal. SPI1MD dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 70 TABLE 4-45: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.2.6 4.3 SOFTWARE STACK In addition to its use as a working register, the W15 register in the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices is also used as a software Stack Pointer. The Stack Pointer always points to the first available free word and grows from lower to higher addresses. It predecrements for stack pops and post-increments for stack pushes, as shown in Figure 4-6. For a PC push during any CALL instruction, the MSb of the PC is zero-extended before the push, ensuring that the MSb is always clear. Note: A PC push during exception processing concatenates the SRL register to the MSb of the PC prior to the push. The Stack Pointer Limit register (SPLIM) associated with the Stack Pointer sets an upper address boundary for the stack. SPLIM is uninitialized at Reset. As is the case for the Stack Pointer, SPLIM<0> is forced to `0' because all stack operations must be word-aligned. Whenever an EA is generated using W15 as a source or destination pointer, the resulting address is compared with the value in SPLIM. If the contents of the Stack Pointer (W15) and the SPLIM register are equal and a push operation is performed, a stack error trap will not occur. The stack error trap will occur on a subsequent push operation. For example, to cause a stack error trap when the stack grows beyond address 0x1000 in RAM, initialize the SPLIM with the value 0x0FFE. Similarly, a Stack Pointer underflow (stack error) trap is generated when the Stack Pointer address is found to be less than 0x0800. This prevents the stack from interfering with the Special Function Register (SFR) space. A write to the SPLIM register should not be immediately followed by an indirect read operation using W15. FIGURE 4-6: Stack Grows Toward Higher Address 0x0000 15 CALL STACK FRAME Instruction Addressing Modes The addressing modes shown in Table 4-48 form the basis of the addressing modes optimized to support the specific features of individual instructions. The addressing modes provided in the MAC class of instructions differ from those in the other instruction types. 4.3.1 FILE REGISTER INSTRUCTIONS Most file register instructions use a 13-bit address field (f) to directly address data present in the first 8192 bytes of data memory (near data space). Most file register instructions employ a working register, W0, which is denoted as WREG in these instructions. The destination is typically either the same file register or WREG (with the exception of the MUL instruction), which writes the result to a register or register pair. The MOV instruction allows additional flexibility and can access the entire data space. 4.3.2 MCU INSTRUCTIONS The three-operand MCU instructions are of the form: Operand 3 = Operand 1 Operand 2 where, Operand 1 is always a working register (that is, the addressing mode can only be register direct), which is referred to as Wb. Operand 2 can be a W register, fetched from data memory, or a 5-bit literal. The result location can be either a W register or a data memory location. The following addressing modes are supported by MCU instructions: * * * * * Register Direct Register Indirect Register Indirect Post-Modified Register Indirect Pre-Modified 5-bit or 10-bit Literal Note: Not all instructions support all the addressing modes given above. Individual instructions can support different subsets of these addressing modes. 0 PC<15:0> 000000000 PC<22:16> W15 (before CALL) W15 (after CALL) POP : [--W15] PUSH : [W15++] (c) 2008-2012 Microchip Technology Inc. DS70318F-page 71 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 4-48: FUNDAMENTAL ADDRESSING MODES SUPPORTED Addressing Mode Description File Register Direct The address of the file register is specified explicitly. Register Direct The contents of a register are accessed directly. Register Indirect The contents of Wn forms the Effective Address (EA). Register Indirect Post-Modified The contents of Wn forms the EA. Wn is post-modified (incremented or decremented) by a constant value. Register Indirect Pre-Modified Wn is pre-modified (incremented or decremented) by a signed constant value to form the EA. Register Indirect with Register Offset The sum of Wn and Wb forms the EA. (Register Indexed) Register Indirect with Literal Offset 4.3.3 The sum of Wn and a literal forms the EA. MOVE AND ACCUMULATOR INSTRUCTIONS Move instructions and the DSP accumulator class of instructions to provide a greater addressing flexibility than other instructions. In addition to the addressing modes supported by most MCU instructions, move and accumulator instructions also support Register Indirect with Register Offset Addressing mode, also referred to as Register Indexed mode. Note: For the MOV instructions, the addressing mode specified in the instruction can differ for the source and destination EA. However, the 4-bit Wb (register offset) field is shared by both source and destination (but typically only used by one). 4.3.4 The dual source operand DSP instructions (CLR, ED, EDAC, MAC, MPY, MPY.N, MOVSAC and MSC), also referred to as MAC instructions, use a simplified set of addressing modes to allow the user application to effectively manipulate the data pointers through register indirect tables. The two-source operand prefetch registers must be members of the set {W8, W9, W10, W11}. For data reads, W8 and W9 are always directed to the X RAGU, and W10 and W11 are always directed to the Y AGU. The effective addresses generated (before and after modification) must, therefore, be valid addresses within X data space for W8 and W9 and Y data space for W10 and W11. Note: In summary, the following addressing modes are supported by move and accumulator instructions: * * * * * * * * Register Direct Register Indirect Register Indirect Post-modified Register Indirect Pre-modified Register Indirect with Register Offset (Indexed) Register Indirect with Literal Offset 8-bit Literal 16-bit Literal Note: Not all instructions support all the addressing modes given above. Individual instructions may support different subsets of these addressing modes. DS70318F-page 72 MAC INSTRUCTIONS Register Indirect with Register Offset Addressing mode is available only for W9 (in X space) and W11 (in Y space). In summary, the following addressing modes are supported by the MAC class of instructions: * * * * * Register Indirect Register Indirect Post-Modified by 2 Register Indirect Post-Modified by 4 Register Indirect Post-Modified by 6 Register Indirect with Register Offset (Indexed) 4.3.5 OTHER INSTRUCTIONS Besides the addressing modes outlined previously, some instructions use literal constants of various sizes. For example, BRA (branch) instructions use 16-bit signed literals to specify the branch destination directly, whereas the DISI instruction uses a 14-bit unsigned literal field. In some instructions, such as ADD Acc, the source of an operand or result is implied by the opcode itself. Certain operations, such as NOP, do not have any operands. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.4 Modulo Addressing Note: Modulo Addressing mode is a method used to provide an automated means to support circular data buffers using hardware. The objective is to remove the need for software to perform data address boundary checks when executing tightly looped code, as is typical in many DSP algorithms. Modulo Addressing can operate in either data or program space (since the data pointer mechanism is essentially the same for both). One circular buffer can be supported in each of the X (which also provides the pointers into program space) and Y data spaces. Modulo Addressing can operate on any W register pointer. However, it is not advisable to use W14 or W15 for Modulo Addressing since these two registers are used as the Stack Frame Pointer and Stack Pointer, respectively. In general, any particular circular buffer can be configured to operate in only one direction as there are certain restrictions on the buffer start address (for incrementing buffers), or end address (for decrementing buffers), based upon the direction of the buffer. The only exception to the usage restrictions is for buffers that have a power-of-two length. As these buffers satisfy the start and end address criteria, they can operate in a bidirectional mode (that is, address boundary checks are performed on both the lower and upper address boundaries). 4.4.1 START AND END ADDRESS The Modulo Addressing scheme requires that a starting and ending address be specified and loaded into the 16-bit Modulo Buffer Address registers: XMODSRT, XMODEND, YMODSRT and YMODEND (see Table 4-1). FIGURE 4-7: Y space Modulo Addressing EA calculations assume word-sized data (LSb of every EA is always clear). The length of a circular buffer is not directly specified. It is determined by the difference between the corresponding start and end addresses. The maximum possible length of the circular buffer is 32K words (64 Kbytes). 4.4.2 W ADDRESS REGISTER SELECTION The Modulo and Bit-Reversed Addressing Control register, MODCON<15:0>, contains enable flags as well as a W register field to specify the W Address registers. The XWM and YWM fields select the registers that will operate with Modulo Addressing: * If XWM = 15, X RAGU and X WAGU Modulo Addressing is disabled. * If YWM = 15, Y AGU Modulo Addressing is disabled. The X Address Space Pointer W register (XWM), to which Modulo Addressing is to be applied, is stored in MODCON<3:0> (see Table 4-1). Modulo Addressing is enabled for X data space when XWM is set to any value other than `15' and the XMODEN bit is set at MODCON<15>. The Y Address Space Pointer W register (YWM) to which Modulo Addressing is to be applied is stored in MODCON<7:4>. Modulo Addressing is enabled for Y data space when YWM is set to any value other than `15' and the YMODEN bit is set at MODCON<14>. MODULO ADDRESSING OPERATION EXAMPLE Byte Address 0x1100 0x1163 MOV MOV MOV MOV MOV MOV #0x1100, W0 W0, XMODSRT #0x1163, W0 W0, MODEND #0x8001, W0 W0, MODCON MOV #0x0000, W0 ;W0 holds buffer fill value MOV #0x1110, W1 ;point W1 to buffer DO AGAIN, #0x31 MOV W0, [W1++] AGAIN: INC W0, W0 ;set modulo start address ;set modulo end address ;enable W1, X AGU for modulo ;fill the 50 buffer locations ;fill the next location ;increment the fill value Start Addr = 0x1100 End Addr = 0x1163 Length = 0x0032 words (c) 2008-2012 Microchip Technology Inc. DS70318F-page 73 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.4.3 MODULO ADDRESSING APPLICABILITY Modulo Addressing can be applied to the Effective Address (EA) calculation associated with any W register. Address boundaries check for addresses equal to: * The upper boundary addresses for incrementing buffers * The lower boundary addresses for decrementing buffers The address boundaries check for addresses less than or greater than the upper (for incrementing buffers) and lower (for decrementing buffers) boundary addresses (not just equal to). Address changes can, therefore, jump beyond boundaries and still be adjusted correctly. Note: The modulo corrected effective address is written back to the register only when PreModify or Post-Modify Addressing mode is used to compute the effective address. When an address offset (such as [W7 + W2]) is used, Modulo Addressing correction is performed but the contents of the register remain unchanged. If the length of a bit-reversed buffer is M = 2N bytes, the last `N' bits of the data buffer start address must be zeros. XB<14:0> is the Bit-Reversed Address modifier, or `pivot point,' which is typically a constant. In the case of an FFT computation, its value is equal to half of the FFT data buffer size. Note: When enabled, Bit-Reversed Addressing is executed only for Register Indirect with Pre-Increment or PostIncrement Addressing and word-sized data writes. It will not function for any other addressing mode or for byte-sized data, and normal addresses are generated instead. When Bit-Reversed Addressing is active, the W Address Pointer is always added to the address modifier (XB), and the offset associated with the Register Indirect Addressing mode is ignored. In addition, as word-sized data is a requirement, the LSb of the EA is ignored (and always clear). Note: 4.5 Bit-Reversed Addressing Bit-Reversed Addressing mode is intended to simplify data re-ordering for radix-2 FFT algorithms. It is supported by the X AGU for data writes only. The modifier, which can be a constant value or register contents, is regarded as having its bit order reversed. The address source and destination are kept in normal order. Thus, the only operand requiring reversal is the modifier. 4.5.1 BIT-REVERSED ADDRESSING IMPLEMENTATION All bit-reversed EA calculations assume word-sized data (LSb of every EA is always clear). The XB value is scaled accordingly to generate compatible (byte) addresses. Modulo Addressing and Bit-Reversed Addressing should not be enabled together. If an application attempts to do so, Bit-Reversed Addressing will assume priority when active for the X WAGU and X WAGU; Modulo Addressing will be disabled. However, Modulo Addressing will continue to function in the X RAGU. If Bit-Reversed Addressing has already been enabled by setting the BREN (XBREV<15>) bit, a write to the XBREV register should not be immediately followed by an indirect read operation using the W register that has been designated as the Bit-Reversed Pointer. Bit-Reversed Addressing mode is enabled in any of these situations: * BWM bits (W register selection) in the MODCON register are any value other than 15 (the stack cannot be accessed using Bit-Reversed Addressing) * The BREN bit is set in the XBREV register * The addressing mode used is Register Indirect with Pre-Increment or Post-Increment DS70318F-page 74 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 4-8: BIT-REVERSED ADDRESS EXAMPLE Sequential Address b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 0 Bit Locations Swapped Left-to-Right Around Center of Binary Value b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b1 b2 b3 b4 0 Bit-Reversed Address Pivot Point XB = 0x0008 for a 16-Word Bit-Reversed Buffer TABLE 4-49: BIT-REVERSED ADDRESS SEQUENCE (16-ENTRY) Normal Address Bit-Reversed Address A3 A2 A1 A0 Decimal A3 A2 A1 A0 Decimal 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 8 0 0 1 0 2 0 1 0 0 4 0 0 1 1 3 1 1 0 0 12 0 1 0 0 4 0 0 1 0 2 0 1 0 1 5 1 0 1 0 10 0 1 1 0 6 0 1 1 0 6 0 1 1 1 7 1 1 1 0 14 1 0 0 0 8 0 0 0 1 1 1 0 0 1 9 1 0 0 1 9 1 0 1 0 10 0 1 0 1 5 1 0 1 1 11 1 1 0 1 13 1 1 0 0 12 0 0 1 1 3 1 1 0 1 13 1 0 1 1 11 1 1 1 0 14 0 1 1 1 7 1 1 1 1 15 1 1 1 1 15 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 75 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.6 Interfacing Program and Data Memory Spaces 4.6.1 The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 architecture uses a 24-bit-wide program space and a 16-bit-wide data space. The architecture is also a modified Harvard scheme, meaning that data can also be present in the program space. To use this data successfully, it must be accessed in a way that preserves the alignment of information in both spaces. For table operations, the 8-bit Table Page register (TBLPAG) is used to define a 32K word region within the program space. This is concatenated with a 16-bit EA to arrive at a full 24-bit program space address. In this format, the Most Significant bit of TBLPAG is used to determine if the operation occurs in the user memory (TBLPAG<7> = 0) or the configuration memory (TBLPAG<7> = 1). Aside from normal execution, the dsPIC33FJ06GS101/ X02 and dsPIC33FJ16GSX02/X04 architecture provides two methods by which program space can be accessed during operation: * Using table instructions to access individual bytes or words anywhere in the program space * Remapping a portion of the program space into the data space (Program Space Visibility) For remapping operations, the 8-bit Program Space Visibility Register (PSVPAG) is used to define a 16K word page in the program space. When the Most Significant bit of the EA is `1', PSVPAG is concatenated with the lower 15 bits of the EA to form a 23-bit program space address. Unlike table operations, this limits remapping operations strictly to the user memory area. Table instructions allow an application to read or write to small areas of the program memory. This capability makes the method ideal for accessing data tables that need to be updated periodically. It also allows access to all bytes of the program word. The remapping method allows an application to access a large block of data on a read-only basis, which is ideal for look ups from a large table of static data. The application can only access the least significant word of the program word. TABLE 4-50: Table 4-50 and Figure 4-9 show how the program EA is created for table operations and remapping accesses from the data EA. Here, P<23:0> refers to a program space word, and D<15:0> refers to a data space word. PROGRAM SPACE ADDRESS CONSTRUCTION Access Space Access Type Instruction Access (Code Execution) User TBLRD/TBLWT (Byte/Word Read/Write) User Program Space Address <23> Program Space Visibility (Block Remap/Read) <22:16> <15> <14:1> PC<22:1> 0 <0> 0 0xx xxxx xxxx xxxx xxxx xxx0 TBLPAG<7:0> 0xxx xxxx Configuration Note 1: ADDRESSING PROGRAM SPACE Since the address ranges for the data and program spaces are 16 and 24 bits, respectively, a method is needed to create a 23-bit or 24-bit program address from 16-bit data registers. The solution depends on the interface method to be used. User Data EA<15:0> xxxx xxxx xxxx xxxx TBLPAG<7:0> Data EA<15:0> 1xxx xxxx xxxx xxxx xxxx xxxx 0 PSVPAG<7:0> 0 xxxx xxxx Data EA<14:0>(1) xxx xxxx xxxx xxxx Data EA<15> is always `1' in this case, but is not used in calculating the program space address. Bit 15 of the address is PSVPAG<0>. DS70318F-page 76 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 4-9: DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION Program Counter(1) Program Counter 0 0 23 bits EA Table Operations(2) 1/0 1/0 TBLPAG 8 bits 16 bits 24 bits Select Program Space Visibility(1) (Remapping) 0 EA 1 0 PSVPAG 8 bits 15 bits 23 bits User/Configuration Space Select Byte Select Note 1: The Least Significant bit (LSb) of program space addresses is always fixed as `0' to maintain word alignment of data in the program and data spaces. 2: Table operations are not required to be word-aligned. Table read operations are permitted in the configuration memory space. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 77 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.6.2 DATA ACCESS FROM PROGRAM MEMORY USING TABLE INSTRUCTIONS The TBLRDL and TBLWTL instructions offer a direct method of reading or writing the lower word of any address within the program space without going through data space. The TBLRDH and TBLWTH instructions are the only method to read or write the upper 8 bits of a program space word as data. The PC is incremented by two for each successive 24-bit program word. This allows program memory addresses to directly map to data space addresses. Program memory can thus be regarded as two 16-bit wide word address spaces, residing side by side, each with the same address range. TBLRDL and TBLWTL access the space that contains the least significant data word. TBLRDH and TBLWTH access the space that contains the upper data byte. Two table instructions are provided to move byte or word-sized (16-bit) data to and from program space. Both function as either byte or word operations. * TBLRDL (Table Read Low): - In Word mode, this instruction maps the lower word of the program space location (P<15:0>) to a data address (D<15:0>). FIGURE 4-10: - In Byte mode, either the upper or lower byte of the lower program word is mapped to the lower byte of a data address. The upper byte is selected when byte select is `1'; the lower byte is selected when it is `0'. * TBLRDH (Table Read High): - In Word mode, this instruction maps the entire upper word of a program address (P<23:16>) to a data address. Note that D<15:8>, the `phantom byte', will always be `0'. - In Byte mode, this instruction maps the upper or lower byte of the program word to D<7:0> of the data address, in the TBLRDL instruction. The data is always `0' when the upper `phantom' byte is selected (Byte Select = 1). Similarly, two table instructions, TBLWTH and TBLWTL, are used to write individual bytes or words to a program space address. The details of their operation are explained in Section 5.0 "Flash Program Memory". For all table operations, the area of program memory space to be accessed is determined by the Table Page register (TBLPAG). TBLPAG covers the entire program memory space of the device, including user and configuration spaces. When TBLPAG<7> = 0, the table page is located in the user memory space. When TBLPAG<7> = 1, the page is located in configuration space. ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS Program Space TBLPAG 02 23 15 0 0x000000 23 16 8 0 00000000 00000000 0x020000 00000000 0x030000 00000000 `Phantom' Byte TBLRDH.B (Wn<0> = 0) TBLRDL.B (Wn<0> = 1) TBLRDL.B (Wn<0> = 0) TBLRDL.W 0x800000 DS70318F-page 78 The address for the table operation is determined by the data EA within the page defined by the TBLPAG register. Only read operations are shown; write operations are also valid in the user memory area. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 4.6.3 READING DATA FROM PROGRAM MEMORY USING PROGRAM SPACE VISIBILITY The upper 32 Kbytes of data space may optionally be mapped into any 16K word page of the program space. This option provides transparent access to stored constant data from the data space without the need to use special instructions (such as TBLRDL/H). Program space access through the data space occurs if the Most Significant bit of the data space EA is `1' and program space visibility is enabled by setting the PSV bit in the Core Control register (CORCON<2>). The location of the program memory space to be mapped into the data space is determined by the Program Space Visibility Page register (PSVPAG). This 8-bit register defines any one of 256 possible pages of 16K words in program space. In effect, PSVPAG functions as the upper 8 bits of the program memory address, with the 15 bits of the EA functioning as the lower bits. By incrementing the PC by 2 for each program memory word, the lower 15 bits of data space addresses directly map to the lower 15 bits in the corresponding program space addresses. Data reads to this area add a cycle to the instruction being executed, since two program memory fetches are required. Although each data space address 8000h and higher maps directly into a corresponding program memory address (see Figure 4-11), only the lower 16 bits of the FIGURE 4-11: 24-bit program word are used to contain the data. The upper 8 bits of any program space location used as data should be programmed with `1111 1111' or `0000 0000' to force a NOP. This prevents possible issues should the area of code ever be accidentally executed. Note: PSV access is temporarily disabled during table reads/writes. For operations that use PSV and are executed outside a REPEAT loop, the MOV and MOV.D instructions require one instruction cycle in addition to the specified execution time. All other instructions require two instruction cycles in addition to the specified execution time. For operations that use PSV, and are executed inside a REPEAT loop, these instances require two instruction cycles in addition to the specified execution time of the instruction: * Execution in the first iteration * Execution in the last iteration * Execution prior to exiting the loop due to an interrupt * Execution upon re-entering the loop after an interrupt is serviced Any other iteration of the REPEAT loop will allow the instruction using PSV to access data, to execute in a single cycle. PROGRAM SPACE VISIBILITY OPERATION When CORCON<2> = 1 and EA<15> = 1: Program Space PSVPAG 02 23 15 Data Space 0 0x000000 0x0000 Data EA<14:0> 0x010000 0x018000 The data in the page designated by PSVPAG is mapped into the upper half of the data memory space... 0x8000 PSV Area 0x800000 (c) 2008-2012 Microchip Technology Inc. ...while the lower 15 bits of the EA specify an exact address within 0xFFFF the PSV area. This corresponds exactly to the same lower 15 bits of the actual program space address. DS70318F-page 79 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 80 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 5.0 FLASH PROGRAM MEMORY power (VDD), ground (VSS) and Master Clear (MCLR). This allows customers to manufacture boards with unprogrammed devices and then program the digital signal controller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 5. "Flash Programming" (DS70191) in the "dsPIC33F/PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). RTSP is accomplished using TBLRD (table read) and TBLWT (table write) instructions. With RTSP, the user application can write program memory data, either in blocks or `rows' of 64 instructions (192 bytes) at a time, or a single program memory word, and erase program memory in blocks or `pages' of 512 instructions (1536 bytes) at a time. 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. 5.1 The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices contain internal Flash program memory for storing and executing application code. The memory is readable, writable and erasable during normal operation over the entire VDD range. Flash memory can be programmed in two ways: Regardless of the method used, all programming of Flash memory is done with the table read and table write instructions. These allow direct read and write access to the program memory space from the data memory while the device is in normal operating mode. The 24-bit target address in the program memory is formed using bits<7:0> of the TBLPAG register and the Effective Address (EA) from a W register specified in the table instruction, as shown in Figure 5-1. The TBLRDL and the TBLWTL instructions are used to read or write to bits<15:0> of program memory. TBLRDL and TBLWTL can access program memory in both Word and Byte modes. * In-Circuit Serial ProgrammingTM (ICSPTM) programming capability * Run-Time Self-Programming (RTSP) ICSP allows a dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 device to be serially programmed while in the end application circuit. This is done with two lines for programming clock and programming data (one of the alternate programming pin pairs: PGECx/PGEDx, and three other lines for FIGURE 5-1: Table Instructions and Flash Programming The TBLRDH and TBLWTH instructions are used to read or write to bits<23:16> of program memory. TBLRDH and TBLWTH can also access program memory in Word or Byte mode. ADDRESSING FOR TABLE REGISTERS 24 bits Using Program Counter Program Counter 0 0 Working Reg EA Using Table Instruction 1/0 TBLPAG Reg 8 bits User/Configuration Space Select (c) 2008-2012 Microchip Technology Inc. 16 bits 24-bit EA Byte Select DS70318F-page 81 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 5.2 RTSP Operation The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 Flash program memory array is organized into rows of 64 instructions or 192 bytes. RTSP allows the user application to erase a page of memory, which consists of eight rows (512 instructions) at a time, and to program one row or one word at a time. Table 24-12 shows typical erase and programming times. The 8-row erase pages and single row write rows are edge-aligned from the beginning of program memory, on boundaries of 1536 bytes and 192 bytes, respectively. The program memory implements holding buffers that can contain 64 instructions of programming data. Prior to the actual programming operation, the write data must be loaded into the buffers sequentially. The instruction words loaded must always be from a group of 64 boundary. The basic sequence for RTSP programming is to set up a Table Pointer, then do a series of TBLWT instructions to load the buffers. Programming is performed by setting the control bits in the NVMCON register. A total of 64 TBLWTL and TBLWTH instructions are required to load the instructions. All of the table write operations are single-word writes (two instruction cycles) because only the buffers are written. A programming cycle is required for programming each row. 5.3 Programming Operations A complete programming sequence is necessary for programming or erasing the internal Flash in RTSP mode. The processor stalls (waits) until the programming operation is finished. The programming time depends on the FRC accuracy (see Table 24-20) and the value of the FRC Oscillator Tuning register (see Register 8-4). Use the following formula to calculate the minimum and maximum values for the Row Write Time, Page Erase Time, and Word Write Cycle Time parameters (see Table 24-12). EQUATION 5-1: PROGRAMMING TIME T ------------------------------------------------------------------------------------------------------------------------7.37 MHz x ( FRC Accuracy )% x ( FRC Tuning )% For example, if the device is operating at +125C, the FRC accuracy will be 5%. If the TUN<5:0> bits (see Register 8-4) are set to `b111111, the minimum row write time is equal to Equation 5-2. EQUATION 5-2: MINIMUM ROW WRITE TIME 11064 Cycles T RW = ---------------------------------------------------------------------------------------------- = 1.435ms 7.37 MHz x ( 1 + 0.05 ) x ( 1 - 0.00375 ) The maximum row write time is equal to Equation 5-3. EQUATION 5-3: MAXIMUM ROW WRITE TIME 11064 Cycles T RW = ---------------------------------------------------------------------------------------------- = 1.586ms 7.37 MHz x ( 1 - 0.05 ) x ( 1 - 0.00375 ) Setting the WR bit (NVMCON<15>) starts the operation, and the WR bit is automatically cleared when the operation is finished. 5.4 Control Registers Two SFRs are used to read and write the program Flash memory: NVMCON and NVMKEY. The NVMCON register (Register 5-1) controls which blocks are to be erased, which memory type is to be programmed and the start of the programming cycle. NVMKEY is a write-only register that is used for write protection. To start a programming or erase sequence, the user application must consecutively write 0x55 and 0xAA to the NVMKEY register. Refer to Section 5.3 "Programming Operations" for further details. DS70318F-page 82 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 5-1: NVMCON: FLASH MEMORY CONTROL REGISTER R/SO-0(1) R/W-0(1) R/W-0(1) U-0 U-0 U-0 U-0 U-0 WR WREN WRERR -- -- -- -- -- bit 15 bit 8 R/W-0(1) U-0 -- U-0 ERASE -- R/W-0(1) U-0 R/W-0(1) R/W-0(1) R/W-0(1) (2) -- NVMOP<3:0> bit 7 bit 0 Legend: SO = Settable Only bit R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 WR: Write Control bit 1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is cleared by hardware once operation is complete. 0 = Program or erase operation is complete and inactive bit 14 WREN: Write Enable bit 1 = Enable Flash program/erase operations 0 = Inhibit Flash program/erase operations bit 13 WRERR: Write Sequence Error Flag bit 1 = An improper program or erase sequence attempt or termination has occurred (bit is set automatically on any set attempt of the WR bit) 0 = The program or erase operation completed normally bit 12-7 Unimplemented: Read as `0' bit 6 ERASE: Erase/Program Enable bit 1 = Perform the erase operation specified by NVMOP<3:0> on the next WR command 0 = Perform the program operation specified by NVMOP<3:0> on the next WR command bit 5-4 Unimplemented: Read as `0' bit 3-0 NVMOP<3:0>: NVM Operation Select bits(2) If ERASE = 1: 1111 = Memory bulk erase operation 1101 = Erase general segment 0011 = No operation 0010 = Memory page erase operation 0001 = No operation 0000 = Erase a single Configuration register byte If ERASE = 0: 1111 = No operation 1101 = No operation 0011 = Memory word program operation 0010 = No operation 0001 = Memory row program operation 0000 = Program a single Configuration register byte Note 1: 2: These bits can only be Reset on POR. All other combinations of NVMOP<3:0> are unimplemented. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 83 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 5-2: NVMKEY: NONVOLATILE MEMORY KEY REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 W-0 W-0 W-0 W-0 W-0 W-0 W-0 W-0 NVMKEY<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-8 Unimplemented: Read as `0' bit 7-0 NVMKEY<7:0>: Key Register bits (write-only) DS70318F-page 84 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 5.4.1 PROGRAMMING ALGORITHM FOR FLASH PROGRAM MEMORY 4. 5. One row of program Flash memory can be programmed at a time. To achieve this, it is necessary to erase the 8-row erase page that contains the desired row. The general process is: 1. 2. 3. Read eight rows of program memory (512 instructions) and store in data RAM. Update the program data in RAM with the desired new data. Erase the block (see Example 5-1): a) Set the NVMOP<3:0> bits (NVMCON<3:0>) to `0010' to configure for block erase. Set the ERASE (NVMCON<6>) and WREN (NVMCON<14>) bits. b) Write the starting address of the page to be erased into the TBLPAG and W registers. c) Write 0x55 to NVMKEY. d) Write 0xAA to NVMKEY. e) Set the WR bit (NVMCON<15>). The erase cycle begins and the CPU stalls for the duration of the erase cycle. When the erase is done, the WR bit is cleared automatically. EXAMPLE 5-1: For protection against accidental operations, the write initiate sequence for the NVMKEY register must be used to allow any erase or program operation to proceed. After the programming command has been executed, the user application must wait for the programming time until programming is complete. The two instructions following the start of the programming sequence should be NOPs, as shown in Example 5-3. ERASING A PROGRAM MEMORY PAGE ; Set up NVMCON for block erase operation MOV #0x4042, W0 MOV W0, NVMCON ; Init pointer to row to be ERASED MOV #tblpage(PROG_ADDR), W0 MOV W0, TBLPAG MOV #tbloffset(PROG_ADDR), W0 TBLWTL W0, [W0] DISI #5 MOV MOV MOV MOV BSET NOP NOP 6. Write the first 64 instructions from data RAM into the program memory buffers (see Example 5-2). Write the program block to Flash memory: a) Set the NVMOP<3:0> bits to `0001' to configure for row programming. Clear the ERASE bit and set the WREN bit. b) Write 0x55 to the NVMKEY register. c) Write 0xAA to the NVMKEY register. d) Set the WR bit. The programming cycle begins and the CPU stalls for the duration of the write cycle. When the write to Flash memory is done, the WR bit is cleared automatically. Repeat steps 4 and 5, using the next available 64 instructions from the block in data RAM by incrementing the value in the TBLPAG register, until all 512 instructions are written back to Flash memory. #0x55, W0 W0, NVMKEY #0xAA, W1 W1, NVMKEY NVMCON, #WR (c) 2008-2012 Microchip Technology Inc. ; ; Initialize NVMCON ; ; ; ; ; ; ; ; ; ; ; ; Initialize PM Page Boundary SFR Initialize in-page EA[15:0] pointer Set base address of erase block Block all interrupts with priority <7 for next 5 instructions Write the 55 key Write the AA key Start the erase sequence Insert two NOPs after the erase command is asserted DS70318F-page 85 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 EXAMPLE 5-2: LOADING THE WRITE BUFFERS ; Set up NVMCON for row programming operations MOV #0x4001, W0 ; MOV W0, NVMCON ; Initialize NVMCON ; Set up a pointer to the first program memory location to be written ; program memory selected, and writes enabled MOV #0x0000, W0 ; MOV W0, TBLPAG ; Initialize PM Page Boundary SFR MOV #0x6000, W0 ; An example program memory address ; Perform the TBLWT instructions to write the latches ; 0th_program_word MOV #LOW_WORD_0, W2 ; MOV #HIGH_BYTE_0, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 1st_program_word MOV #LOW_WORD_1, W2 ; MOV #HIGH_BYTE_1, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 2nd_program_word MOV #LOW_WORD_2, W2 ; MOV #HIGH_BYTE_2, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch * * * ; 63rd_program_word MOV #LOW_WORD_31, W2 ; MOV #HIGH_BYTE_31, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch EXAMPLE 5-3: INITIATING A PROGRAMMING SEQUENCE DISI #5 MOV MOV MOV MOV BSET NOP NOP #0x55, W0 W0, NVMKEY #0xAA, W1 W1, NVMKEY NVMCON, #WR DS70318F-page 86 ; Block all interrupts with priority <7 ; for next 5 instructions ; ; ; ; ; ; Write the 55 key Write the AA key Start the erase sequence Insert two NOPs after the erase command is asserted (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 6.0 RESETS A simplified block diagram of the Reset module is shown in Figure 6-1. Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 8. "Reset" (DS70192) in the "dsPIC33F/PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The Reset module combines all Reset sources and controls the device Master Reset Signal, SYSRST. The following is a list of device Reset sources: * * * * * * * * POR: Power-on Reset BOR: Brown-out Reset MCLR: Master Clear Pin Reset SWR: Software RESET Instruction WDTO: Watchdog Timer Reset CM: Configuration Mismatch Reset TRAPR: Trap Conflict Reset IOPUWR: Illegal Condition Device Reset - Illegal Opcode Reset - Uninitialized W Register Reset - Security Reset FIGURE 6-1: Any active source of reset will make the SYSRST signal active. On system Reset, some of the registers associated with the CPU and peripherals are forced to a known Reset state and some are unaffected. Note: Refer to the specific peripheral section or Section 3.0 "CPU" of this data sheet for register Reset states. All types of device Reset sets a corresponding status bit in the RCON register to indicate the type of Reset (see Register 6-1). A POR clears all the bits, except for the POR bit (RCON<0>), that are set. The user application can set or clear any bit at any time during code execution. The RCON bits only serve as status bits. Setting a particular Reset status bit in software does not cause a device Reset to occur. The RCON register also has other bits associated with the Watchdog Timer and device power-saving states. The function of these bits is discussed in other sections of this manual. Note: The status bits in the RCON register should be cleared after they are read so that the next RCON register value after a device Reset is meaningful. RESET SYSTEM BLOCK DIAGRAM RESET Instruction Glitch Filter MCLR WDT Module Sleep or Idle BOR Internal Regulator SYSRST VDD VDD Rise Detect POR Trap Conflict Illegal Opcode Uninitialized W Register Configuration Mismatch (c) 2008-2012 Microchip Technology Inc. DS70318F-page 87 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 RCON: RESET CONTROL REGISTER(1) REGISTER 6-1: R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 TRAPR IOPUWR -- -- -- -- CM VREGS bit 15 bit 8 R/W-0 EXTR R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 SWR SWDTEN(2) WDTO SLEEP IDLE BOR POR bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred bit 14 IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit 1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an Address Pointer caused a Reset 0 = An illegal opcode or uninitialized W Reset has not occurred bit 13-10 Unimplemented: Read as `0' bit 9 CM: Configuration Mismatch Flag bit 1 = A Configuration Mismatch Reset has occurred 0 = A Configuration Mismatch Reset has NOT occurred bit 8 VREGS: Voltage Regulator Standby During Sleep bit 1 = Voltage regulator is active during Sleep 0 = Voltage regulator goes into Standby mode during Sleep bit 7 EXTR: External Reset Pin (MCLR) bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 6 SWR: Software Reset Flag (Instruction) bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed bit 5 SWDTEN: Software Enable/Disable of WDT bit(2) 1 = WDT is enabled 0 = WDT is disabled bit 4 WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred bit 3 SLEEP: Wake-up from Sleep Flag bit 1 = Device has been in Sleep mode 0 = Device has not been in Sleep mode bit 2 IDLE: Wake-up from Idle Flag bit 1 = Device was in Idle mode 0 = Device was not in Idle mode Note 1: 2: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset. If the FWDTEN Configuration bit is `1' (unprogrammed), the WDT is always enabled, regardless of the SWDTEN bit setting. DS70318F-page 88 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 6-1: RCON: RESET CONTROL REGISTER(1) (CONTINUED) bit 1 BOR: Brown-out Reset Flag bit 1 = A Brown-out Reset has occurred 0 = A Brown-out Reset has not occurred bit 0 POR: Power-on Reset Flag bit 1 = A Power-up Reset has occurred 0 = A Power-up Reset has not occurred Note 1: 2: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not cause a device Reset. If the FWDTEN Configuration bit is `1' (unprogrammed), the WDT is always enabled, regardless of the SWDTEN bit setting. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 89 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 6.1 System Reset * Cold Reset * Warm Reset A warm Reset is the result of all the other Reset sources, including the RESET instruction. On warm Reset, the device will continue to operate from the current clock source as indicated by the Current Oscillator Selection (COSC<2:0>) bits in the Oscillator Control (OSCCON<14:12>) register. A cold Reset is the result of a Power-on Reset (POR) or a Brown-out Reset (BOR). On a cold Reset, the FNOSC Configuration bits in the FOSC Configuration register select the device clock source. The device is kept in a Reset state until the system power supplies have stabilized at appropriate levels and the oscillator clock is ready. The sequence in which this occurs is detailed in Figure 6-2. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 families of devices have two types of Reset: TABLE 6-1: OSCILLATOR DELAY Oscillator Mode Oscillator Startup Delay Oscillator Startup Timer PLL Lock Time Total Delay FRC, FRCDIV16, FRCDIVN TOSCD(1) -- -- TOSCD(1) FRCPLL TOSCD(1) -- TLOCK(3) TOSCD + TLOCK(1,3) XT TOSCD(1) -- TOSCD + TOST(1,2) HS TOSCD(1) TOST(2) TOST(2) -- TOSCD + TOST(1,2) EC -- -- -- -- XTPLL TOSCD(1) TOST(2) TLOCK(3) TOSCD + TOST + TLOCK(1,2,3) HSPLL TOSCD(1) TOST(2) TLOCK(3) TOSCD + TOST + TLOCK(1,2,3) ECPLL -- -- TLOCK(3) TLOCK(3) LPRC TOSCD(1) -- -- TOSCD(1) Note 1: 2: 3: TOSCD = Oscillator start-up delay (1.1 s max for FRC, 70 s max for LPRC). Crystal oscillator start-up times vary with crystal characteristics, load capacitance, etc. TOST = Oscillator start-up timer delay (1024 oscillator clock period). For example, TOST = 102.4 s for a 10 MHz crystal and TOST = 32 ms for a 32 kHz crystal. TLOCK = PLL lock time (1.5 ms nominal) if PLL is enabled. DS70318F-page 90 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 6-2: SYSTEM RESET TIMING VBOR VPOR VDD TPOR 1 POR Reset TBOR 2 BOR Reset 3 TPWRT SYSRST 4 Oscillator Clock TOSCD TOST TLOCK 6 TFSCM FSCM 5 Reset Device Status Run Time Note 1: POR Reset: A POR circuit holds the device in Reset when the power supply is turned on. The POR circuit is active until VDD crosses the VPOR threshold and the delay, TPOR, has elapsed. 2: BOR Reset: The on-chip voltage regulator has a BOR circuit that keeps the device in Reset until VDD crosses the VBOR threshold and the delay, TBOR, has elapsed. The delay, TBOR, ensures the voltage regulator output becomes stable. 3: PWRT Timer: The programmable power-up timer continues to hold the processor in Reset for a specific period of time (TPWRT) after a BOR. The delay, TPWRT, ensures that the system power supplies have stabilized at the appropriate level for full-speed operation. After the delay, TPWRT has elapsed and the SYSRST becomes inactive, which in turn, enables the selected oscillator to start generating clock cycles. 4: Oscillator Delay: The total delay for the clock to be ready for various clock source selections is given in Table 6-1. Refer to Section 8.0 "Oscillator Configuration" for more information. 5: When the oscillator clock is ready, the processor begins execution from location 0x000000. The user application programs a GOTO instruction at the Reset address, which redirects program execution to the appropriate start-up routine. 6: If the Fail-Safe Clock Monitor (FSCM) is enabled, it begins to monitor the system clock when the system clock is ready and the delay, TFSCM, has elapsed. TABLE 6-2: Symbol OSCILLATOR DELAY Parameter Value VPOR POR threshold 1.8V nominal TPOR POR extension time 30 s maximum VBOR BOR threshold 2.5V nominal TBOR BOR extension time 100 s maximum TPWRT Programmable power-up time delay 0-128 ms nominal TFSCM Fail-Safe Clock Monitor 900 s maximum delay (c) 2008-2012 Microchip Technology Inc. Note: When the device exits the Reset condition (begins normal operation), the device operating parameters (voltage, frequency, temperature, etc.) must be within their operating ranges; otherwise, the device may not function correctly. The user application must ensure that the delay between the time power is first applied, and the time SYSRST becomes inactive, is long enough to get all operating parameters within specification. DS70318F-page 91 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 6.2 Power-on Reset (POR) A Power-on Reset (POR) circuit ensures the device is reset from power-on. The POR circuit is active until VDD crosses the VPOR threshold and the delay, TPOR, has elapsed. The delay, TPOR, ensures the internal device bias circuits become stable. The device supply voltage characteristics must meet the specified starting voltage and rise rate requirements to generate the POR. Refer to Section 24.0 "Electrical Characteristics" for details. The POR status (POR) bit in the Reset Control (RCON<0>) register is set to indicate the Power-on Reset. 6.2.1 Brown-out Reset (BOR) and Power-up Timer (PWRT) The on-chip regulator has a Brown-out Reset (BOR) circuit that resets the device when the VDD is too low (VDD < VBOR) for proper device operation. The BOR circuit keeps the device in Reset until VDD crosses the FIGURE 6-3: VBOR threshold and the delay, TBOR, has elapsed. The delay, TBOR, ensures the voltage regulator output becomes stable. The BOR status (BOR) bit in the Reset Control (RCON<1>) register is set to indicate the Brown-out Reset. The device will not run at full speed after a BOR as the VDD should rise to acceptable levels for full-speed operation. The PWRT provides power-up time delay (TPWRT) to ensure that the system power supplies have stabilized at the appropriate levels for full-speed operation before the SYSRST is released. The power-up timer delay (TPWRT) is programmed by the Power-on Reset Timer Value Select (FPWRT<2:0>) bits in the POR Configuration (FPOR<2:0>) register, which provides eight settings (from 0 ms to 128 ms). Refer to Section 21.0 "Special Features" for further details. Figure 6-3 shows the typical brown-out scenarios. The reset delay (TBOR + TPWRT) is initiated each time VDD rises above the VBOR trip point. BROWN-OUT SITUATIONS VDD VBOR TBOR + TPWRT SYSRST VDD VBOR TBOR + TPWRT SYSRST VDD dips before PWRT expires VDD VBOR TBOR + TPWRT SYSRST DS70318F-page 92 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 6.3 External Reset (EXTR) The external Reset is generated by driving the MCLR pin low. The MCLR pin is a Schmitt trigger input with an additional glitch filter. Reset pulses that are longer than the minimum pulse width will generate a Reset. Refer to Section 24.0 "Electrical Characteristics" for minimum pulse width specifications. The external Reset (MCLR) pin (EXTR) bit in the Reset Control (RCON) register is set to indicate the MCLR Reset. 6.3.0.1 EXTERNAL SUPERVISORY CIRCUIT Many systems have external supervisory circuits that generate Reset signals to reset multiple devices in the system. This external Reset signal can be directly connected to the MCLR pin to reset the device when the rest of system is reset. 6.3.0.2 INTERNAL SUPERVISORY CIRCUIT When using the internal power supervisory circuit to reset the device, the external Reset pin (MCLR) should be tied directly or resistively to VDD. In this case, the MCLR pin will not be used to generate a Reset. The external Reset pin (MCLR) does not have an internal pull-up and must not be left unconnected. 6.4 Software RESET Instruction (SWR) Whenever the RESET instruction is executed, the device will assert SYSRST, placing the device in a special Reset state. This Reset state will not re-initialize the clock. The clock source in effect prior to the RESET instruction will remain. SYSRST is released at the next instruction cycle and the Reset vector fetch will commence. The Software Reset (SWR) flag (instruction) in the Reset Control (RCON<6>) register is set to indicate the software Reset. 6.5 Watchdog Time-out Reset (WDTO) Whenever a Watchdog time-out occurs, the device will asynchronously assert SYSRST. The clock source will remain unchanged. A WDT time-out during Sleep or Idle mode will wake-up the processor, but will not reset the processor. The Watchdog Timer Time-out (WDTO) flag in the Reset Control (RCON<4>) register is set to indicate the Watchdog Reset. Refer to Section 21.4 "Watchdog Timer (WDT)" for more information on Watchdog Reset. (c) 2008-2012 Microchip Technology Inc. 6.6 Trap Conflict Reset If a lower priority hard trap occurs while a higher priority trap is being processed, a hard Trap Conflict Reset occurs. The hard traps include exceptions of priority level 13 through level 15, inclusive. The address error (level 13) and oscillator error (level 14) traps fall into this category. The Trap Reset (TRAPR) flag in the Reset Control (RCON<15>) register is set to indicate the Trap Conflict Reset. Refer to Section 7.0 "Interrupt Controller" for more information on Trap Conflict Resets. 6.7 Configuration Mismatch Reset To maintain the integrity of the Peripheral Pin Select Control registers, they are constantly monitored with shadow registers in hardware. If an unexpected change in any of the registers occur (such as cell disturbances caused by ESD or other external events), a Configuration Mismatch Reset occurs. The Configuration Mismatch (CM) flag in the Reset Control (RCON<9>) register is set to indicate the Configuration Mismatch Reset. Refer to Section 10.0 "I/O Ports" for more information on the Configuration Mismatch Reset. Note: 6.8 The Configuration Mismatch Reset feature and associated Reset flag are not available on all devices. Illegal Condition Device Reset An illegal condition device Reset occurs due to the following sources: * Illegal Opcode Reset * Uninitialized W Register Reset * Security Reset The Illegal Opcode or Uninitialized W Access Reset (IOPUWR) flag in the Reset Control (RCON<14>) register is set to indicate the illegal condition device Reset. 6.8.1 ILLEGAL OPCODE RESET A device Reset is generated if the device attempts to execute an illegal opcode value that is fetched from program memory. The Illegal Opcode Reset function can prevent the device from executing program memory sections that are used to store constant data. To take advantage of the Illegal Opcode Reset, use only the lower 16 bits of each program memory section to store the data values. The upper 8 bits should be programmed with 3Fh, which is an illegal opcode value. DS70318F-page 93 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 6.8.2 UNINITIALIZED W REGISTER RESET The VFC occurs when the program counter is reloaded with an interrupt or trap vector. Any attempt to use the uninitialized W register as an Address Pointer will Reset the device. The W register array (with the exception of W15) is cleared during all Resets and is considered uninitialized until written to. 6.8.3 6.9 SECURITY RESET If a Program Flow Change (PFC) or Vector Flow Change (VFC) targets a restricted location in a protected segment (boot and secure segment), that operation will cause a Security Reset. The PFC occurs when the program counter is reloaded as a result of a call, jump, computed jump, return, return from subroutine or other form of branch instruction. TABLE 6-3: Refer to Section 21.8 "Code Protection and CodeGuardTM Security" for more information on Security Reset. Using the RCON Status Bits The user application can read the Reset Control (RCON) register after any device Reset to determine the cause of the Reset. Note: The status bits in the RCON register should be cleared after they are read so that the next RCON register value after a device Reset will be meaningful. Table 6-3 provides a summary of the Reset flag bit operation. RESET FLAG BIT OPERATION Flag Bit Set by: Cleared by: TRAPR (RCON<15>) Trap conflict event POR,BOR IOPWR (RCON<14>) Illegal opcode or uninitialized W register access or Security Reset POR,BOR CM (RCON<9>) Configuration Mismatch POR,BOR EXTR (RCON<7>) MCLR Reset POR SWR (RCON<6>) RESET instruction POR,BOR WDTO (RCON<4>) WDT time-out PWRSAV instruction, CLRWDT instruction, POR,BOR SLEEP (RCON<3>) PWRSAV #SLEEP instruction POR,BOR IDLE (RCON<2>) PWRSAV #IDLE instruction POR,BOR BOR (RCON<1>) POR, BOR -- POR (RCON<0>) POR -- Note: All Reset flag bits can be set or cleared by user software. DS70318F-page 94 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 7.0 INTERRUPT CONTROLLER Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 41. "Interrupts (Part IV)" (DS70300) in the "dsPIC33F/ PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 interrupt controller reduces the numerous peripheral interrupt request signals to a single interrupt request signal to the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CPU. It has the following features: * Up to eight processor exceptions and software traps * Seven user-selectable priority levels * Interrupt Vector Table (IVT) with up to 118 vectors * A unique vector for each interrupt or exception source * Fixed priority within a specified user priority level * Alternate Interrupt Vector Table (AIVT) for debug support * Fixed interrupt entry and return latencies 7.1 Interrupt Vector Table The Interrupt Vector Table (IVT) is shown in Figure 7-1. The IVT resides in program memory, starting at location 000004h. The IVT contains 126 vectors, consisting of eight nonmaskable trap vectors, plus up to 118 sources of interrupt. In general, each interrupt source has its own vector. Each interrupt vector contains a 24-bit-wide address. The value programmed into each interrupt vector location is the starting address of the associated Interrupt Service Routine (ISR). (c) 2008-2012 Microchip Technology Inc. Interrupt vectors are prioritized in terms of their natural priority. This priority is linked to their position in the vector table. Lower addresses generally have a higher natural priority. For example, the interrupt associated with vector 0 will take priority over interrupts at any other vector address. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices implement up to 35 unique interrupts and 4 non-maskable traps. These are summarized in Table 7-1. 7.1.1 ALTERNATE INTERRUPT VECTOR TABLE The Alternate Interrupt Vector Table (AIVT) is located after the IVT, as shown in Figure 7-1. Access to the AIVT is provided by the ALTIVT control bit (INTCON2<15>). If the ALTIVT bit is set, all interrupt and exception processes use the alternate vectors instead of the default vectors. The alternate vectors are organized in the same manner as the default vectors. The AIVT supports debugging by providing a means to switch between an application and a support environment without requiring the interrupt vectors to be reprogrammed. This feature also enables switching between applications for evaluation of different software algorithms at run time. If the AIVT is not needed, the AIVT should be programmed with the same addresses used in the IVT. 7.2 Reset Sequence A device Reset is not a true exception because the interrupt controller is not involved in the Reset process. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 device clears its registers in response to a Reset, which forces the PC to zero. The digital signal controller then begins program execution at location 0x000000. A GOTO instruction at the Reset address can redirect program execution to the appropriate start-up routine. Note: Any unimplemented or unused vector locations in the IVT and AIVT should be programmed with the address of a default interrupt handler routine that contains a RESET instruction. DS70318F-page 95 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Decreasing Natural Order Priority FIGURE 7-1: Note 1: DS70318F-page 96 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 INTERRUPT VECTOR TABLE Reset - GOTO Instruction Reset - GOTO Address Reserved Oscillator Fail Trap Vector Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 Interrupt Vector 1 ~ ~ ~ Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 ~ ~ ~ Interrupt Vector 116 Interrupt Vector 117 Reserved Reserved Reserved Oscillator Fail Trap Vector Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 Interrupt Vector 1 ~ ~ ~ Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 ~ ~ ~ Interrupt Vector 116 Interrupt Vector 117 Start of Code 0x000000 0x000002 0x000004 0x000014 0x00007C 0x00007E 0x000080 Interrupt Vector Table (IVT)(1) 0x0000FC 0x0000FE 0x000100 0x000102 0x000114 Alternate Interrupt Vector Table (AIVT)(1) 0x00017C 0x00017E 0x000180 0x0001FE 0x000200 See Table 7-1 for the list of implemented interrupt vectors. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 7-1: INTERRUPT VECTORS Vector Number Interrupt Request (IQR) 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22-23 24 25 26 27 28 29-36 37 38-64 65 66-72 73 74-101 102 103 104 105 106-110 111 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14-15 16 17 18 19 20 21-28 29 30-56 57 58-64 65 66-93 94 95 96 97 98-102 103 112 113 114-117 118 119 120 121 122 123 124 125 104 105 106-109 110 111 112 113 114 115 116 117 IVT Address AIVT Address Interrupt Source Highest Natural Order Priority 0x000014 0x000114 INT0 - External Interrupt 0 0x000016 0x000116 IC1 - Input Capture 1 0x000018 0x000118 OC1 - Output Compare 1 0x00001A 0x00011A T1 - Timer1 0x00001C 0x00011C Reserved 0x00001E 0x00011E IC2 - Input Capture 2 0x000020 0x000120 OC2 - Output Compare 2 0x000022 0x000122 T2 - Timer2 0x000024 0x000124 T3 - Timer3 0x000026 0x000126 SPI1E - SPI1 Fault 0x000028 0x000128 SPI1 - SPI1 Transfer Done 0x00002A 0x00012A U1RX - UART1 Receiver 0x00002C 0x00012C U1TX - UART1 Transmitter 0x00002E 0x00012E ADC - ADC Group Convert Done 0x000030-0x000032 0x000130-0x000132 Reserved 0x000034 0x000134 SI2C1 - I2C1 Slave Event 0x000036 0x000136 MI2C1 - I2C1 Master Event 0x000038 0x000138 CMP1 - Analog Comparator 1 Interrupt 0x00003A 0x00013A CN - Input Change Notification Interrupt 0x00003C 0x00013C INT1 - External Interrupt 1 0x00003E-0x00004C 0x00013E-0x00014C Reserved 0x00004E 0x00014E INT2 - External Interrupt 2 0x000050-0x000084 0x000150-0x000184 Reserved 0x000086 0x000186 PWM PSEM Special Event Match 0x000088-0x000094 0x000188-0x000194 Reserved 0x000096 0x000196 U1E - UART1 Error Interrupt 0x000098-0x0000CE 0x000198-0x0001CE Reserved 0x0000D0 0x0001D0 PWM1 - PWM1 Interrupt 0x0000D2 0x0001D2 PWM2 - PWM2 Interrupt 0x0000D4 0x0001D4 PWM3 - PWM3 Interrupt 0x0000D6 0x0001D6 PWM4 - PWM4 Interrupt 0x0000D8-0x0000E0 0x0001D8-0x0001E0 Reserved 0x0000E2 0x00001E2 CMP2 - Analog Comparator 2 0x0000E4 0x0001E4 0x0000E6 0x0001E6 0x0000E8-0x0000EE 0x0001E8-0x0001EE 0x0000F0 0x0001F0 0x0000F2 0x0001F2 0x0000F4 0x0001F4 0x0000F6 0x0001F6 0x0000F8 0x0001F8 0x0000FA 0x0001FA 0x0000FC 0x0001FC 0x0000FE 0x0001FE Lowest Natural Order Priority (c) 2008-2012 Microchip Technology Inc. CMP3 - Analog Comparator 3 CMP4 - Analog Comparator 4 Reserved ADC Pair 0 Convert Done ADC Pair 1 Convert Done ADC Pair 2 Convert Done ADC Pair 3 Convert Done ADC Pair 4 Convert Done ADC Pair 5 Convert Done ADC Pair 6 Convert Done Reserved DS70318F-page 97 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 7.3 Interrupt Control and Status Registers The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices implement 27 registers for the interrupt controller: * * * * * * INTCON1 INTCON2 IFSx IECx IPCx INTTREG 7.3.1 INTCON1 AND INTCON2 Global interrupt control functions are controlled from INTCON1 and INTCON2. INTCON1 contains the Interrupt Nesting Disable (NSTDIS) bit as well as the control and status flags for the processor trap sources. The INTCON2 register controls the external interrupt request signal behavior and the use of the Alternate Interrupt Vector Table. 7.3.2 IFSx The IFSx registers maintain all of the interrupt request flags. Each source of interrupt has a status bit, which is set by the respective peripherals or external signal and is cleared via software. 7.3.3 IECx The IECx registers maintain all of the interrupt enable bits. These control bits are used to individually enable interrupts from the peripherals or external signals. 7.3.4 7.3.5 INTTREG The INTTREG register contains the associated interrupt vector number and the new CPU Interrupt priority Level, which are latched into the Vector Number (VECNUM<6:0>) and Interrupt Level (ILR<3:0>) bit fields in the INTTREG register. The new Interrupt Priority Level is the priority of the pending interrupt. The interrupt sources are assigned to the IFSx, IECx and IPCx registers in the same sequence that they are listed in Table 7-1. For example, the INT0 (External Interrupt 0) is shown as having vector number 8 and a natural order priority of 0. Thus, the INT0IF bit is found in IFS0<0>, the INT0IE bit is found in IEC0<0> and the INT0IP bits are found in the first position of IPC0 (IPC0<2:0>). 7.3.6 STATUS/CONTROL REGISTERS Although they are not specifically part of the interrupt control hardware, two of the CPU Control registers contain bits that control interrupt functionality. * The CPU STATUS register, SR, contains the IPL<2:0> bits (SR<7:5>). These bits indicate the current CPU interrupt Priority Level. The user can change the current CPU priority level by writing to the IPL bits. * The CORCON register contains the IPL3 bit, which together with IPL<2:0>, indicates the current CPU priority level. IPL3 is a read-only bit so that trap events cannot be masked by the user software. All Interrupt registers are described in Register 7-1 through Register 7-35 in the following pages. IPCx The IPCx registers are used to set the Interrupt Priority Level for each source of interrupt. Each user interrupt source can be assigned to one of eight priority levels. DS70318F-page 98 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-1: SR: CPU STATUS REGISTER(1) R-0 R-0 R/C-0 R/C-0 R-0 R/C-0 R -0 R/W-0 OA OB SA SB OAB SAB DA DC bit 15 bit 8 R/W-0(3) R/W-0(3) R/W-0(3) IPL<2:0>(2) R-0 R/W-0 R/W-0 R/W-0 R/W-0 RA N OV Z C bit 7 bit 0 Legend: C = Clearable bit R = Readable bit U = Unimplemented bit, read as `0' S = Settable bit W = Writable bit -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown IPL<2:0>: CPU Interrupt Priority Level Status bits(2) 111 = CPU Interrupt Priority Level is 7 (15), user interrupts disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 7-5 Note 1: 2: 3: For complete register details, see Register 3-1. The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when IPL<3> = 1. The IPL<2:0> status bits are read-only when NSTDIS (INTCON1<15>) = 1. REGISTER 7-2: U-0 -- bit 15 U-0 -- R/W-0 SATB Legend: R = Readable bit 0' = Bit is cleared Note 1: 2: U-0 -- U-0 US R/W-0 EDT R-0 R-0 DL<2:0> R-0 bit 8 R/W-0 SATA bit 7 bit 3 CORCON: CORE CONTROL REGISTER(1) R/W-1 SATDW R/W-0 ACCSAT C = Clearable bit W = Writable bit `x = Bit is unknown R/C-0 IPL3(2) R/W-0 PSV R/W-0 RND R/W-0 IF bit 0 -n = Value at POR `1' = Bit is set U = Unimplemented bit, read as `0' IPL3: CPU Interrupt Priority Level Status bit 3(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less For complete register details, see Register 3-2. The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 99 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-3: INTCON1: INTERRUPT CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE OVBTE COVTE bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 SFTACERR DIV0ERR -- MATHERR ADDRERR STKERR OSCFAIL -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 NSTDIS: Interrupt Nesting Disable bit 1 = Interrupt nesting is disabled 0 = Interrupt nesting is enabled bit 14 OVAERR: Accumulator A Overflow Trap Flag bit 1 = Trap was caused by overflow of Accumulator A 0 = Trap was not caused by overflow of Accumulator A bit 13 OVBERR: Accumulator B Overflow Trap Flag bit 1 = Trap was caused by overflow of Accumulator B 0 = Trap was not caused by overflow of Accumulator B bit 12 COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit 1 = Trap was caused by catastrophic overflow of Accumulator A 0 = Trap was not caused by catastrophic overflow of Accumulator A bit 11 COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit 1 = Trap was caused by catastrophic overflow of Accumulator B 0 = Trap was not caused by catastrophic overflow of Accumulator B bit 10 OVATE: Accumulator A Overflow Trap Enable bit 1 = Trap overflow of Accumulator A 0 = Trap disabled bit 9 OVBTE: Accumulator B Overflow Trap Enable bit 1 = Trap overflow of Accumulator B 0 = Trap disabled bit 8 COVTE: Catastrophic Overflow Trap Enable bit 1 = Trap on catastrophic overflow of Accumulator A or B enabled 0 = Trap disabled bit 7 SFTACERR: Shift Accumulator Error Status bit 1 = Math error trap was caused by an invalid accumulator shift 0 = Math error trap was not caused by an invalid accumulator shift bit 6 DIV0ERR: Arithmetic Error Status bit 1 = Math error trap was caused by a divide by zero 0 = Math error trap was not caused by a divide by zero bit 5 Unimplemented: Read as `0' bit 4 MATHERR: Arithmetic Error Status bit 1 = Math error trap has occurred 0 = Math error trap has not occurred bit 3 ADDRERR: Address Error Trap Status bit 1 = Address error trap has occurred 0 = Address error trap has not occurred DS70318F-page 100 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-3: INTCON1: INTERRUPT CONTROL REGISTER 1 (CONTINUED) bit 2 STKERR: Stack Error Trap Status bit 1 = Stack error trap has occurred 0 = Stack error trap has not occurred bit 1 OSCFAIL: Oscillator Failure Trap Status bit 1 = Oscillator failure trap has occurred 0 = Oscillator failure trap has not occurred bit 0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. DS70318F-page 101 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-4: INTCON2: INTERRUPT CONTROL REGISTER 2 R/W-0 R-0 U-0 U-0 U-0 U-0 U-0 U-0 ALTIVT DISI -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 -- -- -- -- -- INT2EP INT1EP INT0EP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 ALTIVT: Enable Alternate Interrupt Vector Table bit 1 = Use alternate vector table 0 = Use standard (default) vector table bit 14 DISI: DISI Instruction Status bit 1 = DISI instruction is active 0 = DISI instruction is not active bit 13-3 Unimplemented: Read as `0' bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge DS70318F-page 102 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-5: IFS0: INTERRUPT FLAG STATUS REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- ADIF U1TXIF U1RXIF SPI1IF SPI1EIF T3IF bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 T2IF OC2IF IC2IF -- T1IF OC1IF IC1IF INT0IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-14 Unimplemented: Read as `0' bit 13 ADIF: ADC Group Conversion Complete Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 U1TXIF: UART1 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 U1RXIF: UART1 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 SPI1IF: SPI1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 9 SPI1EIF: SPI1 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 T3IF: Timer3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7 T2IF: Timer2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6 OC2IF: Output Compare Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 5 IC2IF: Input Capture Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4 Unimplemented: Read as `0' bit 3 T1IF: Timer1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 OC1IF: Output Compare Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 103 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-5: IFS0: INTERRUPT FLAG STATUS REGISTER 0 (CONTINUED) bit 1 IC1IF: Input Capture Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 INT0IF: External Interrupt 0 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS70318F-page 104 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-6: IFS1: INTERRUPT FLAG STATUS REGISTER 1 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 -- -- INT2IF -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- INT1IF CNIF AC1IF MI2C1IF SI2C1IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-14 Unimplemented: Read as `0' bit 13 INT2IF: External Interrupt 2 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12-5 Unimplemented: Read as `0' bit 4 INT1IF: External Interrupt 1 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 3 CNIF: Input Change Notification Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 AC1IF: Analog Comparator 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 MI2C1IF: I2C1 Master Events Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 SI2C1IF: I2C1 Slave Events Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 105 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-7: IFS3: INTERRUPT FLAG STATUS REGISTER 3 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 -- -- -- -- -- -- PSEMIF -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-10 Unimplemented: Read as `0' bit 9 PSEMIF: PWM Special Event Match Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8-0 Unimplemented: Read as `0' REGISTER 7-8: x = Bit is unknown IFS4: INTERRUPT FLAG STATUS REGISTER 4 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 -- -- -- -- -- -- U1EIF -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-2 Unimplemented: Read as `0' bit 1 U1EIF: UART1 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 Unimplemented: Read as `0' DS70318F-page 106 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-9: IFS5: INTERRUPT FLAG STATUS REGISTER 5 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 PWM2IF PWM1IF -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 PWM2IF: PWM2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 14 PWM1IF: PWM1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 13-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 107 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-10: IFS6: INTERRUPT FLAG STATUS REGISTER 6 R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 ADCP1IF ADCP0IF -- -- -- -- AC4IF AC3IF bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 AC2IF -- -- -- -- -- PWM4IF PWM3IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 ADCP1IF: ADC Pair 1 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 14 ADCP0IF: ADC Pair 0 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 13-10 Unimplemented: Read as `0' bit 9 AC4IF: Analog Comparator 4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 AC3IF: Analog Comparator 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7 AC2IF: Analog Comparator 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6-2 Unimplemented: Read as `0' bit 1 PWM4IF: PWM4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 PWM3IF: PWM3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS70318F-page 108 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-11: IFS7: INTERRUPT FLAG STATUS REGISTER 7 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- ADCP6IF ADCP5IF ADCP4IF ADCP3IF ADCP2IF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-5 Unimplemented: Read as `0' bit 4 ADCP6IF: ADC Pair 6 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 3 ADCP5IF: ADC Pair 5 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 ADCP4IF: ADC Pair 4 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 ADCP3IF: ADC Pair 3 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 ADCP2IF: ADC Pair 2 Conversion Done Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 109 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-12: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- ADIE U1TXIE U1RXIE SPI1IE SPI1EIE T3IE bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 T2IE OC2IE IC2IE -- T1IE OC1IE IC1IE INT0IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-14 Unimplemented: Read as `0' bit 13 ADIE: ADC1 Conversion Complete Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12 U1TXIE: UART1 Transmitter Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 11 U1RXIE: UART1 Receiver Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 10 SPI1IE: SPI1 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 9 SPI1EIE: SPI1 Event Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 8 T3IE: Timer3 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 7 T2IE: Timer2 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 6 OC2IE: Output Compare Channel 2 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 5 IC2IE: Input Capture Channel 2 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 4 Unimplemented: Read as `0' bit 3 T1IE: Timer1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 2 OC1IE: Output Compare Channel 1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled DS70318F-page 110 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-12: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 (CONTINUED) bit 1 IC1IE: Input Capture Channel 1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 INT0IE: External Interrupt 0 Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled (c) 2008-2012 Microchip Technology Inc. DS70318F-page 111 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-13: IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 -- -- INT2IE -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- INT1IE CNIE AC1IE MI2C1IE SI2C1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-14 Unimplemented: Read as `0' bit 13 INT2IE: External Interrupt 2 Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 12-5 Unimplemented: Read as `0' bit 4 INT1IE: External Interrupt 1 Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 3 CNIE: Input Change Notification Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 2 AC1IE: Analog Comparator 1 Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 1 MI2C1IE: I2C1 Master Events Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 SI2C1IE: I2C1 Slave Events Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled DS70318F-page 112 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-14: IEC3: INTERRUPT ENABLE CONTROL REGISTER 3 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 -- -- -- -- -- -- PSEMIE -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-10 Unimplemented: Read as `0' bit 9 PSEMIE: PWM Special Event Match Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 8-0 Unimplemented: Read as `0' REGISTER 7-15: x = Bit is unknown IEC4: INTERRUPT ENABLE CONTROL REGISTER 4 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 -- -- -- -- -- -- U1EIE -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-2 Unimplemented: Read as `0' bit 1 U1EIE: UART1 Error Interrupt Enable bit 1 = Interrupt request enabled 0 = Interrupt request not enabled bit 0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 113 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-16: IEC5: INTERRUPT ENABLE CONTROL REGISTER 5 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 PWM2IE PWM1IE -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 PWM2IE: PWM2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 14 PWM1IE: PWM1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 13-0 Unimplemented: Read as `0' DS70318F-page 114 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-17: IEC6: INTERRUPT ENABLE CONTROL REGISTER 6 R/W-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 ADCP1IE ADCP0IE -- -- -- -- AC4IE AC3IE bit 15 bit 8 R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 AC2IE -- -- -- -- -- PWM4IE PWM3IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 ADCP1IE: ADC Pair 1 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 14 ADCP0IE: ADC Pair 0 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 13-10 Unimplemented: Read as `0 bit 9 AC4IE: Analog Comparator 4 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 8 AC3IE: Analog Comparator 3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 7 AC2IE: Analog Comparator 2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 6-2 Unimplemented: Read as `0' bit 1 PWM4IE: PWM4 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 PWM3IE: PWM3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 115 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-18: IEC7: INTERRUPT ENABLE CONTROL REGISTER 7 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- ADCP6IE ADCP5IE ADCP4IE ADCP3IE ADCP2IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-5 Unimplemented: Read as `0' bit 4 ADCP6IE: ADC Pair 6 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 3 ADCP5IE: ADC Pair 5 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 2 ADCP4IE: ADC Pair 4 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 1 ADCP3IE: ADC Pair 3 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 ADCP2IE: ADC Pair 2 Conversion Done Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled DS70318F-page 116 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-19: U-0 IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0 R/W-1 -- R/W-0 R/W-0 T1IP<2:0> U-0 R/W-1 -- R/W-0 R/W-0 OC1IP<2:0> bit 15 bit 8 U-0 R/W-1 -- R/W-0 IC1IP<2:0> R/W-0 U-0 R/W-1 -- R/W-0 R/W-0 INT0IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 T1IP<2:0>: Timer1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 OC1IP<2:0>: Output Compare Channel 1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as `0' bit 6-4 IC1IP<2:0>: Input Capture Channel 1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 INT0IP<2:0>: External Interrupt 0 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 117 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-20: U-0 IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1 R/W-1 -- R/W-0 R/W-0 T2IP<2:0> U-0 R/W-1 -- R/W-0 R/W-0 OC2IP<2:0> bit 15 bit 8 U-0 R/W-1 -- R/W-0 IC2IP<2:0> R/W-0 U-0 U-0 U-0 U-0 -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 T2IP<2:0>: Timer2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 OC2IP<2:0>: Output Compare Channel 2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as `0' bit 6-4 IC2IP<2:0>: Input Capture Channel 2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as `0' DS70318F-page 118 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-21: U-0 IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2 R/W-1 -- R/W-0 R/W-0 U1RXIP<2:0> U-0 R/W-1 -- R/W-0 R/W-0 SPI1IP<2:0> bit 15 bit 8 U-0 R/W-1 -- R/W-0 SPI1EIP<2:0> R/W-0 U-0 -- R/W-1 R/W-0 R/W-0 T3IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 SPI1IP<2:0>: SPI1 Event Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as `0' bit 6-4 SPI1EIP<2:0>: SPI1 Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 T3IP<2:0>: Timer3 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 119 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-22: IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/W-1 -- R/W-0 ADIP<2:0> R/W-0 U-0 R/W-1 -- R/W-0 R/W-0 U1TXIP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-7 Unimplemented: Read as `0' bit 6-4 ADIP<2:0>: ADC1 Conversion Complete Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS70318F-page 120 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-23: U-0 IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4 R/W-1 -- R/W-0 R/W-0 CNIP<2:0> U-0 R/W-1 -- R/W-0 R/W-0 AC1IP<2:0> bit 15 bit 8 U-0 R/W-1 -- R/W-0 MI2C1IP<2:0> R/W-0 U-0 -- R/W-1 R/W-0 R/W-0 SI2C1IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 CNIP<2:0>: Change Notification Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 AC1IP<2:0>: Analog Comparator 1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as `0' bit 6-4 MI2C1IP<2:0>: I2C1 Master Events Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 SI2C1IP<2:0>: I2C1 Slave Events Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 121 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-24: IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- R/W-1 R/W-0 R/W-0 INT1IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-3 Unimplemented: Read as `0' bit 2-0 INT1IP<2:0>: External Interrupt 1 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled REGISTER 7-25: x = Bit is unknown IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7 U-0 U-1 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/W-1 -- R/W-0 INT2IP<2:0> R/W-0 U-0 U-0 U-0 U-0 -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-7 Unimplemented: Read as `0' bit 6-4 INT2IP<2:0>: External Interrupt 2 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as `0' DS70318F-page 122 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-26: IPC14: INTERRUPT PRIORITY CONTROL REGISTER 14 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/W-1 -- R/W-0 R/W-0 PSEMIP<2:0> U-0 U-0 U-0 U-0 -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as `0' bit 6-4 PSEMIP<2:0>: PWM Special Event Match Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as `0' REGISTER 7-27: IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/W-1 -- R/W-0 U1EIP<2:0> R/W-0 U-0 U-0 U-0 U-0 -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-7 Unimplemented: Read as `0' bit 6-4 U1EIP<2:0>: UART1 Error Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 123 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-28: U-0 IPC23: INTERRUPT PRIORITY CONTROL REGISTER 23 R/W-1 -- R/W-0 R/W-0 U-0 PWM2IP R/W-1 -- R/W-0 R/W-0 PWM1IP<2:0> bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 PWM2IP<2:0>: PWM2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 PWM1IP<2:0>: PWM1 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7-0 Unimplemented: Read as `0' DS70318F-page 124 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-29: IPC24: INTERRUPT PRIORITY CONTROL REGISTER 24 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/W-1 -- R/W-0 R/W-0 U-0 PWM4IP -- R/W-1 R/W-0 R/W-0 PWM3IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-7 Unimplemented: Read as `0' bit 6-4 PWM4IP<2:0>: PWM4 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 PWM3IP<2:0>: PWM3 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 125 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-30: U-0 IPC25: INTERRUPT PRIORITY CONTROL REGISTER 25 R/W-1 -- R/W-0 R/W-0 AC2IP<2:0> U-0 U-0 U-0 U-0 -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 AC2IP<2:0>: Analog Comparator 2 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11-01 Unimplemented: Read as `0' DS70318F-page 126 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-31: IPC26: INTERRUPT PRIORITY CONTROL REGISTER 26 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/W-1 -- R/W-0 AC4IP<2:0> R/W-0 U-0 -- R/W-1 R/W-0 R/W-0 AC3IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-7 Unimplemented: Read as `0' bit 6-4 AC4IP<2:0>: Analog Comparator 4 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 AC3IP<2:0>: Analog Comparator 3 Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 127 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-32: U-0 IPC27: INTERRUPT PRIORITY CONTROL REGISTER 27 R/W-1 -- R/W-0 R/W-0 ADCP1IP<2:0> U-0 R/W-1 -- R/W-0 R/W-0 ADCP0IP<2:0> bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as `0' bit 14-12 ADCP1IP<2:0>: ADC Pair 1 Conversion Done Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 ADCP0IP<2:0>: ADC Pair 0 Conversion Done Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7-0 Unimplemented: Read as `0' DS70318F-page 128 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-33: U-0 IPC28: INTERRUPT PRIORITY CONTROL REGISTER 28 R/W-1 -- R/W-0 R/W-0 ADCP5IP<2:0> U-0 R/W-1 -- R/W-0 R/W-0 ADCP4IP<2:0> bit 15 bit 8 U-0 R/W-1 -- R/W-0 ADCP3IP<2:0> R/W-0 U-0 R/W-1 -- R/W-0 R/W-0 ADCP2IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 Unimplemented: Read as `0' bit 14-12 ADCP5IP<2:0>: ADC Pair 5 Conversion Done Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as `0' bit 10-8 ADCP4IP<2:0>: ADC Pair 4 Conversion Done Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as `0' bit 6-4 ADCP3IP<2:0>: ADC Pair 3 Conversion Done Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as `0' bit 2-0 ADCP2IP<2:0>: ADC Pair 2 Conversion Done Interrupt Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 129 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-34: IPC29: INTERRUPT PRIORITY CONTROL REGISTER 29 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- R/W-1 R/W-0 R/W-0 ADCP6IP<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as `0' bit 2-0 ADCP6IP<2:0>: ADC Pair 6 Conversion Done Interrupt 1 Priority bits 111 = Interrupt is priority 7 (highest priority interrupt) * * * 001 = Interrupt is priority 1 000 = Interrupt source is disabled DS70318F-page 130 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 7-35: INTTREG: INTERRUPT CONTROL AND STATUS REGISTER U-0 U-0 U-0 U-0 -- -- -- -- R-0 R-0 R-0 R-0 ILR<3:0> bit 15 bit 8 U-0 R-0 R-0 -- R-0 R-0 R-0 R-0 R-0 VECNUM<6:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-12 Unimplemented: Read as `0' bit 11-8 ILR<3:0>: New CPU Interrupt Priority Level bits 1111 = CPU Interrupt Priority Level is 15 * * * 0001 = CPU Interrupt Priority Level is 1 0000 = CPU Interrupt Priority Level is 0 bit 7 Unimplemented: Read as `0' bit 6-0 VECNUM<6:0>: Vector Number of Pending Interrupt bits 0111111 = Interrupt vector pending is number 135 * * * 0000001 = Interrupt vector pending is number 9 0000000 = Interrupt vector pending is number 8 (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 131 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 7.4 Interrupt Setup Procedures 7.4.1 7.4.3 INITIALIZATION Complete the following steps to configure an interrupt source at initialization: 1. 2. Set the NSTDIS bit (INTCON1<15>) if nested interrupts are not desired. Select the user-assigned priority level for the interrupt source by writing the control bits in the appropriate IPCx register. The priority level will depend on the specific application and type of interrupt source. If multiple priority levels are not desired, the IPCx register control bits for all enabled interrupt sources can be programmed to the same non-zero value. Note: 3. 4. At a device Reset, the IPCx registers are initialized such that all user interrupt sources are assigned to priority level 4. Clear the interrupt flag status bit associated with the peripheral in the associated IFSx register. Enable the interrupt source by setting the interrupt enable control bit associated with the source in the appropriate IECx register. 7.4.2 TRAP SERVICE ROUTINE A Trap Service Routine (TSR) is coded like an ISR, except that the appropriate trap status flag in the INTCON1 register must be cleared to avoid re-entry into the TSR. 7.4.4 INTERRUPT DISABLE The following steps outline the procedure to disable all user interrupts: 1. 2. Push the current SR value onto the software stack using the PUSH instruction. Force the CPU to priority level 7 by inclusive ORing the value 0xE0 with SRL. To enable user interrupts, the POP instruction can be used to restore the previous SR value. Note: Only user interrupts with a priority level of 7 or lower can be disabled. Trap sources (level 8-level 15) cannot be disabled. The DISI instruction provides a convenient way to disable interrupts of priority levels 1-6 for a fixed period of time. Level 7 interrupt sources are not disabled by the DISI instruction. INTERRUPT SERVICE ROUTINE The method used to declare an ISR and initialize IVT with the correct vector address depends on programming language (C or assembler) and language development toolsuite used to develop application. the the the the In general, the user application must clear the interrupt flag in the appropriate IFSx register for the source of interrupt that the ISR handles. Otherwise, program will re-enter the ISR immediately after exiting the routine. If the ISR is coded in assembly language, it must be terminated using a RETFIE instruction to unstack the saved PC value, SRL value and old CPU priority level. DS70318F-page 132 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 8.0 OSCILLATOR CONFIGURATION The oscillator system provides: * External and internal oscillator options as clock sources * An on-chip Phase-Locked Loop (PLL) to scale the internal operating frequency to the required system clock frequency * An internal FRC oscillator that can also be used with the PLL, thereby allowing full-speed operation without any external clock generation hardware * Clock switching between various clock sources * Programmable clock postscaler for system power savings * A Fail-Safe Clock Monitor (FSCM) that detects clock failure and takes fail-safe measures * A Clock Control register (OSCCON) * Nonvolatile Configuration bits for main oscillator selection. * Auxiliary PLL for ADC and PWM Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 42. "Oscillator (Part IV)" (DS70307) in the "dsPIC33F/ PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. A simplified diagram of the oscillator system is shown in Figure 8-1. FIGURE 8-1: OSCILLATOR SYSTEM DIAGRAM Primary Oscillator DOZE<2:0> POSCCLK S3 R(2) PLL(1) S1 XT, HS, EC XTPLL, HSPLL, ECPLL, FRCPLL FVCO S2 S1/S3 (1) FCY(3) DOZE OSC1 OSC2 POSCMD<1:0> FRC Oscillator FRCDIV FP(3) FRCCLK FRCDIVN S7 / 2 FOSC FRCDIV<2:0> TUN<5:0> FRCDIV16 / 16 FRC LPRC LPRC Oscillator S6 S0 S5 Reference Clock Generation POSCCLK / N FOSC Clock Fail REFCLKO Clock Switch Reset RPx NOSC<2:0> FNOSC<2:0> S7 ROSEL WDT, PWRT, FSCM RODIV<3:0> Auxiliary Clock Generation POSCCLK FRCCLK ASRCSEL Note 1: 2: 3: FVCO(1) APLL(1) x16 FRCSEL ACLK To PWM/ADC(1) / N ENAPLL SELACLK APSTSCLR<2:0> See Section 8.1.3 "PLL Configuration" and Section 8.2 "Auxiliary Clock Generation" for configuration restrictions. If the Oscillator is used with XT or HS modes, an external parallel resistor with the value of 1 M must be connected. The term FP refers to the clock source for all the peripherals, while FCY refers to the clock source for the CPU. Throughout this document, FCY and FP are used interchangeably, except in the case of Doze mode. FP and FCY will be different when Doze mode is used in any ratio other than 1:1, which is the default. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 133 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 8.1 CPU Clocking System The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices provide six system clock options: * * * * * * Fast RC (FRC) Oscillator FRC Oscillator with PLL Primary (XT, HS or EC) Oscillator Primary Oscillator with PLL Low-Power RC (LPRC) Oscillator FRC Oscillator with Postscaler 8.1.1 The FRC frequency depends on the FRC accuracy (see Table 24-20) and the value of the FRC Oscillator Tuning register (see Register 8-4). 8.1.2 SYSTEM CLOCK SOURCES The Fast RC (FRC) internal oscillator runs at a nominal frequency of 7.37 MHz. User software can tune the FRC frequency. User software can optionally specify a factor (ranging from 1:2 to 1:256) by which the FRC clock frequency is divided. This factor is selected using the FRCDIV<2:0> (CLKDIV<10:8>) bits. The primary oscillator can use one of the following as its clock source: SYSTEM CLOCK SELECTION The oscillator source used at a device Power-on Reset event is selected using Configuration bit settings. The oscillator Configuration bit settings are located in the Configuration registers in the program memory. (Refer to Section 21.1 "Configuration Bits" for further details.) The Initial Oscillator Selection Configuration bits, FNOSC<2:0> (FOSCSEL<2:0>), and the Primary Oscillator Mode Select Configuration bits, POSCMD<1:0> (FOSC<1:0>), select the oscillator source that is used at a Power-on Reset. The FRC primary oscillator is the default (unprogrammed) selection. The Configuration bits allow users to choose among 12 different clock modes, shown in Table 8-1. * XT (Crystal): Crystals and ceramic resonators in the range of 3 MHz to 10 MHz. The crystal is connected to the OSC1 and OSC2 pins. * HS (High-Speed Crystal): Crystals in the range of 10 MHz to 40 MHz. The crystal is connected to the OSC1 and OSC2 pins. * EC (External Clock): The external clock signal is directly applied to the OSC1 pin. The LPRC internal oscIllator runs at a nominal frequency of 32.768 kHz. It is also used as a reference clock by the Watchdog Timer (WDT) and Fail-Safe Clock Monitor (FSCM). The clock signals generated by the FRC and primary oscillators can be optionally applied to an on-chip Phase-Locked Loop (PLL) to provide a wide range of TABLE 8-1: output frequencies for device operation. PLL configuration is described in Section 8.1.3 "PLL Configuration". The output of the oscillator (or the output of the PLL if a PLL mode has been selected), FOSC, is divided by 2 to generate the device instruction clock (FCY) and the peripheral clock time base (FP). FCY defines the operating speed of the device and speeds up to 40 MHz are supported by the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 architecture. Instruction execution speed or device operating frequency, FCY, is given by Equation 8-1. EQUATION 8-1: DEVICE OPERATING FREQUENCY FCY = FOSC/2 CONFIGURATION BIT VALUES FOR CLOCK SELECTION Oscillator Mode Oscillator Source POSCMD<1:0> FNOSC<2:0> See Note Fast RC Oscillator with Divide-by-N (FRCDIVN) Internal xx 111 1, 2 Fast RC Oscillator with Divide-by-16 (FRCDIV16) Internal xx 110 1 Low-Power RC Oscillator (LPRC) Internal xx 101 1 Reserved Reserved xx 100 -- Primary Oscillator (HS) with PLL (HSPLL) Primary 10 011 -- Primary Oscillator (XT) with PLL (XTPLL) Primary 01 011 -- Primary Oscillator (EC) with PLL (ECPLL) Primary 00 011 1 Primary Oscillator (HS) Primary 10 010 -- Primary Oscillator (XT) Primary 01 010 -- Primary Oscillator (EC) Primary 00 010 1 Fast RC Oscillator with PLL (FRCPLL) Internal xx 001 1 Fast RC Oscillator (FRC) Internal xx 000 1 Note 1: 2: OSC2 pin function is determined by the OSCIOFNC Configuration bit. This is the default oscillator mode for an unprogrammed (erased) device. DS70318F-page 134 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 8.1.3 PLL CONFIGURATION The primary oscillator and internal FRC oscillator can optionally use an on-chip PLL to obtain higher speeds of operation. The PLL provides significant flexibility in selecting the device operating speed. A block diagram of the PLL is shown in Figure 8-2. The output of the primary oscillator or FRC, denoted as `FIN', is divided down by a prescale factor (N1) of 2, 3, ... or 33 before being provided to the PLL's Voltage Controlled Oscillator (VCO). The input to the VCO must be selected in the range of 0.8 MHz to 8 MHz. The prescale factor `N1' is selected using the PLLPRE<4:0> bits (CLKDIV<4:0>). The PLL Feedback Divisor, selected using the PLLDIV<8:0> bits (PLLFBD<8:0>), provides a factor, `M', by which the input to the VCO is multiplied. This factor must be selected such that the resulting VCO output frequency is in the range of 100 MHz to 200 MHz. The VCO output is further divided by a postscale factor, `N2'. This factor is selected using the PLLPOST<1:0> bits (CLKDIV<7:6>). `N2' can be either 2, 4, or 8, and must be selected such that the PLL output frequency (FOSC) is in the range of 12.5 MHz to 80 MHz, which generates device operating speeds of 6.25-40 MIPS. FIGURE 8-2: For a primary oscillator or FRC oscillator, output `FIN', the PLL output `FOSC' is given by Equation 8-2. EQUATION 8-2: FOSC CALCULATION FOSC = FIN * M ( N1*N2 ) For example, suppose a 10 MHz crystal is being used with the selected oscillator mode of XT with PLL (see Equation 8-3). * If PLLPRE<4:0> = 0, then N1 = 2. This yields a VCO input of 10/2 = 5 MHz, which is within the acceptable range of 0.8-8 MHz. * If PLLDIV<8:0> = 0x1E, then M = 32. This yields a VCO output of 5 x 32 = 160 MHz, which is within the 100-200 MHz ranged needed. * If PLLPOST<1:0> = 0, then N2 = 2. This provides a Fosc of 160/2 = 80 MHz. The resultant device operating speed is 80/2 = 40 MIPS. EQUATION 8-3: FCY = FOSC 2 = XT WITH PLL MODE EXAMPLE 1 10000000 * 32 ( ) = 40 MIPS 2 2*2 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 PLL BLOCK DIAGRAM FVCO 100-200 MHz Here(1) 0.8-8.0 MHz Here(1) Source (Crystal, External Clock or Internal RC) PLLPRE X VCO PLLDIV N1 Divide by 2-33 M Divide by 2-513 PLLPOST 12.5-80 MHz Here(1) FOSC N2 Divide by 2, 4, 8 Note 1: This frequency range must be satisfied at all times. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 135 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 8.2 Auxiliary Clock Generation The auxiliary clock generation is used for a peripherals that need to operate at a frequency unrelated to the system clock such as a PWM or ADC. The primary oscillator and internal FRC oscillator sources can be used with an auxiliary PLL to obtain the auxiliary clock. The auxiliary PLL has a fixed 16x multiplication factor. The auxiliary clock has the following configuration restrictions: * For proper PWM operation, auxiliary clock generation must be configured for 120 MHz (see parameter OS56 in Table 24-18 in Section 24.0 "Electrical Characteristics"). If a slower frequency is desired, the PWM Input Clock Prescaler (Divider) Select bits (PCLKDIV<2:0>) should be used. * To achieve 1.04 ns PWM resolution, the auxiliary clock must use the 16x auxiliary PLL (APLL). All other clock sources will have a minimum PWM resolution of 8 ns. * If the primary PLL is used as a source for the auxiliary clock, the primary PLL should be configured up to a maximum operation of 30 MIPS or less 8.3 Reference Clock Generation The reference clock output logic provides the user with the ability to output a clock signal based on the system clock or the crystal oscillator on a device pin. The user application can specify a wide range of clock scaling prior to outputting the reference clock. DS70318F-page 136 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 8.4 Oscillator Control Registers OSCCON: OSCILLATOR CONTROL REGISTER(1,2) REGISTER 8-1: U-0 R-0 -- R-0 R-0 COSC<2:0> U-0 R/W-y R/W-y R/W-y NOSC<2:0>(3) -- bit 15 bit 8 R/W-0 R/W-0 R-0 U-0 R/C-0 U-0 U-0 R/W-0 CLKLOCK IOLOCK LOCK -- CF -- -- OSWEN bit 7 bit 0 Legend: y = Value set from Configuration bits on POR R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as `0' bit 14-12 COSC<2:0>: Current Oscillator Selection bits (read-only) 111 = Fast RC oscillator (FRC) with divide-by-n 110 = Fast RC oscillator (FRC) with divide-by-16 101 = Low-Power RC oscillator (LPRC) 100 = Reserved 011 = Primary oscillator (XT, HS, EC) with PLL 010 = Primary oscillator (XT, HS, EC) 001 = Fast RC oscillator (FRC) with PLL 000 = Fast RC oscillator (FRC) bit 11 Unimplemented: Read as `0' bit 10-8 NOSC<2:0>: New Oscillator Selection bits(3) 111 = Fast RC oscillator (FRC) with divide-by-n 110 = Fast RC oscillator (FRC) with divide-by-16 101 = Low-Power RC oscillator (LPRC) 100 = Reserved 011 = Primary oscillator (XT, HS, EC) with PLL 010 = Primary oscillator (XT, HS, EC) 001 = Fast RC oscillator (FRC) with PLL 000 = Fast RC oscillator (FRC) bit 7 CLKLOCK: Clock Lock Enable bit If clock switching is enabled and FSCM is disabled, (FOSC = 0b01): 1 = Clock switching is disabled, system clock source is locked 0 = Clock switching is enabled, system clock source can be modified by clock switching bit 6 IOLOCK: Peripheral Pin Select Lock bit 1 = Peripherial pin select is locked, write to Peripheral Pin Select registers not allowed 0 = Peripherial pin select is not locked, write to Peripheral Pin Select registers allowed bit 5 LOCK: PLL Lock Status bit (read-only) 1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied 0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled bit 4 Unimplemented: Read as `0' Note 1: 2: 3: Writes to this register require an unlock sequence. Refer to Section 42. "Oscillator (Part IV)" (DS70307) in the "dsPIC33F/PIC24H Family Reference Manual" (available from the Microchip website) for details. This register is reset only on a Power-on Reset (POR). Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transition clock source between the two PLL modes. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 137 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 8-1: OSCCON: OSCILLATOR CONTROL REGISTER(1,2) (CONTINUED) bit 3 CF: Clock Fail Detect bit (read/clear by application) 1 = FSCM has detected clock failure 0 = FSCM has not detected clock failure bit 2-1 Unimplemented: Read as `0' bit 0 OSWEN: Oscillator Switch Enable bit 1 = Request oscillator switch to selection specified by NOSC<2:0> bits 0 = Oscillator switch is complete Note 1: 2: 3: Writes to this register require an unlock sequence. Refer to Section 42. "Oscillator (Part IV)" (DS70307) in the "dsPIC33F/PIC24H Family Reference Manual" (available from the Microchip website) for details. This register is reset only on a Power-on Reset (POR). Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transition clock source between the two PLL modes. DS70318F-page 138 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 8-2: R/W-0 ROI bit 15 CLKDIV: CLOCK DIVISOR REGISTER(1) R/W-0 R/W-1 DOZE<2:0> Legend: R = Readable bit -n = Value at POR bit 14-12 bit 11 bit 10-8 bit 7-6 bit 5 bit 4-0 Note 1: 2: R/W-0 DOZEN(2) R/W-0 R/W-0 FRCDIV<2:0> R/W-0 bit 8 R/W-0 R/W-1 PLLPOST<1:0> bit 7 bit 15 R/W-1 U-0 -- R/W-0 R/W-0 R/W-0 PLLPRE<4:0> R/W-0 R/W-0 bit 0 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown ROI: Recover on Interrupt bit 1 = Interrupts will clear the DOZEN bit and the processor clock/peripheral clock ratio is set to 1:1 0 = Interrupts have no effect on the DOZEN bit DOZE<2:0>: Processor Clock Reduction Select bits 111 = FCY/128 110 = FCY/64 101 = FCY/32 100 = FCY/16 011 = FCY/8 (default) 010 = FCY/4 001 = FCY/2 000 = FCY/1 DOZEN: Doze Mode Enable bit(2) 1 = DOZE<2:0> field specifies the ratio between the peripheral clocks and the processor clocks 0 = Processor clock/peripheral clock ratio forced to 1:1 FRCDIV<2:0>: Internal Fast RC Oscillator Postscaler bits 111 = FRC divide by 256 110 = FRC divide by 64 101 = FRC divide by 32 100 = FRC divide by 16 011 = FRC divide by 8 010 = FRC divide by 4 001 = FRC divide by 2 000 = FRC divide by 1 (default) PLLPOST<1:0>: PLL VCO Output Divider Select bits (also denoted as `N2', PLL postscaler) 11 = Output/8 10 = Reserved 01 = Output/4 (default) 00 = Output/2 Unimplemented: Read as `0' PLLPRE<4:0>: PLL Phase Detector Input Divider bits (also denoted as `N1', PLL prescaler) 11111 = Input/33 * * * 00001 = Input/3 00000 = Input/2 (default) This register is reset only on a Power-on Reset (POR). This bit is cleared when the ROI bit is set and an interrupt occurs. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 139 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 8-3: PLLFBD: PLL FEEDBACK DIVISOR REGISTER(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 -- -- -- -- -- -- -- PLLDIV<8> bit 15 bit 8 R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-0 PLLDIV<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as `0' bit 8-0 PLLDIV<8:0>: PLL Feedback Divisor bits (also denoted as `M', PLL multiplier) 111111111 = 513 * * * 000110000 = 50 (default) * * * 000000010 = 4 000000001 = 3 000000000 = 2 Note 1: This register is reset only on a Power-on Reset (POR). DS70318F-page 140 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 8-4: OSCTUN: FRC OSCILLATOR TUNING REGISTER(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TUN<5:0>(2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-6 Unimplemented: Read as `0' bit 5-0 TUN<5:0>: FRC Oscillator Tuning bits(2) 011111 = Center frequency + 11.625% (8.23 MHz) 011110 = Center frequency + 11.25% (8.20 MHz) * * * 000001 = Center frequency + 0.375% (7.40 MHz) 000000 = Center frequency (7.37 MHz nominal) 111111 = Center frequency -0.375% (7.345 MHz) * * * 100001 = Center frequency -11.625% (6.52 MHz) 100000 = Center frequency -12% (6.49 MHz) Note 1: 2: x = Bit is unknown This register is reset only on a Power-on Reset (POR). OSCTUN functionality has been provided to help customers compensate for temperature effects on the FRC frequency over a wide range of temperatures. The tuning step size is an approximation and is neither characterized nor tested. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 141 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 ACLKCON: AUXILIARY CLOCK DIVISOR CONTROL REGISTER(1) REGISTER 8-5: R/W-0 R-0 R/W-1 U-0 U-0 ENAPLL APLLCK SELACLK -- -- R/W-1 R/W-1 R/W-1 APSTSCLR<2:0> bit 15 bit 0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 ASRCSEL FRCSEL -- -- -- -- -- -- bit 7 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 ENAPLL: Auxiliary PLL Enable bit 1 = APLL is enabled 0 = APLL is disabled bit 14 APLLCK: APLL Locked Status bit (read-only) 1 = Indicates that auxiliary PLL is in lock 0 = Indicates that auxiliary PLL is not in lock bit 13 SELACLK: Select Auxiliary Clock Source for Auxiliary Clock Divider bit 1 = Auxiliary Oscillators provides the source clock for auxiliary clock divider 0 = Primary PLL (FVCO) provides the source clock for auxiliary clock divider bit 12-11 Unimplemented: Read as `0' bit 10-8 APSTSCLR<2:0>: Auxiliary Clock Output Divider bits 111 = Divided by 1 110 = Divided by 2 101 = Divided by 4 100 = Divided by 8 011 = Divided by 16 010 = Divided by 32 001 = Divided by 64 000 = Divided by 256 bit 7 ASRCSEL: Select Reference Clock Source for Auxiliary Clock bit 1 = Primary oscillator is the clock source 0 = No clock input is selected bit 6 FRCSEL: Select Reference Clock Source for Auxiliary PLL bit 1 = Select FRC clock for auxiliary PLL 0 = Input clock source is determined by ASRCSEL bit setting bit 5-0 Unimplemented: Read as `0' Note 1: This register is reset only on a Power-on Reset (POR). DS70318F-page 142 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 8-6: REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 ROON -- ROSSLP ROSEL R/W-0 R/W-0 R/W-0 R/W-0 RODIV<3:0>(1) bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 ROON: Reference Oscillator Output Enable bit 1 = Reference oscillator output enabled on REFCLK0(2) pin 0 = Reference oscillator output disabled bit 14 Unimplemented: Read as `0' bit 13 ROSSLP: Reference Oscillator Run in Sleep bit 1 = Reference oscillator output continues to run in Sleep 0 = Reference oscillator output is disabled in Sleep bit 12 ROSEL: Reference Oscillator Source Select bit 1 = Oscillator crystal used as the reference clock 0 = System clock used as the reference clock bit 11-8 RODIV<3:0>: Reference Oscillator Divider bits(1) 1111 = Reference clock divided by 32,768 1110 = Reference clock divided by 16,384 1101 = Reference clock divided by 8,192 1100 = Reference clock divided by 4,096 1011 = Reference clock divided by 2,048 1010 = Reference clock divided by 1,024 1001 = Reference clock divided by 512 1000 = Reference clock divided by 256 0111 = Reference clock divided by 128 0110 = Reference clock divided by 64 0101 = Reference clock divided by 32 0100 = Reference clock divided by 16 0011 = Reference clock divided by 8 0010 = Reference clock divided by 4 0001 = Reference clock divided by 2 0000 = Reference clock bit 7-0 Unimplemented: Read as `0' Note 1: 2: x = Bit is unknown The reference oscillator output must be disabled (ROON = 0) before writing to these bits. This pin is remappable. Refer to Section 10.6 "Peripheral Pin Select" for more information. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 143 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 8.5 Clock Switching Operation Users can switch applications among any of the four clock sources (primary, LP, FRC and LPRC) under software control at any time. To limit the possible side effects of this flexibility, dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices have a safeguard lock built into the switch process. Note: 8.5.1 Primary oscillator mode has three different submodes (XT, HS and EC), which are determined by the POSCMD<1:0> Configuration bits. While an application can switch to and from primary oscillator mode in software, it cannot switch among the different primary submodes without reprogramming the device. ENABLING CLOCK SWITCHING To enable clock switching, the FCKSM1 Configuration bit in the Configuration register must be programmed to `0'. (Refer to Section 21.1 "Configuration Bits" for further details.) If the FCKSM1 Configuration bit is unprogrammed (`1'), the clock switching function and Fail-Safe Clock Monitor function are disabled. This is the default setting. 2. If a valid clock switch has been initiated, the LOCK (OSCCON<5>) and the CF (OSCCON<3>) status bits are cleared. The new oscillator is turned on by the hardware if it is not currently running. If a crystal oscillator must be turned on, the hardware waits until the Oscillator Start-up Timer (OST) expires. If the new source is using the PLL, the hardware waits until a PLL lock is detected (LOCK = 1). The hardware waits for 10 clock cycles from the new clock source and then performs the clock switch. The hardware clears the OSWEN bit to indicate a successful clock transition. In addition, the NOSC<2:0> bit values are transferred to the COSC<2:0> status bits. The old clock source is turned off at this time, with the exception of LPRC (if WDT or FSCM are enabled). 3. 4. 5. 6. Note 1: The processor continues to execute code throughout the clock switching sequence. Timing-sensitive code should not be executed during this time. 2: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transition clock source between the two PLL modes. 3: Refer to Section 42. "Oscillator (Part IV)" (DS70307) in the "dsPIC33F/PIC24H Family Reference Manual" for details. The NOSC<2:0> control bits (OSCCON<10:8>) do not control the clock selection when clock switching is disabled. However, the COSC<2:0> bits (OSCCON<14:12>) reflect the clock source selected by the FNOSC Configuration bits. The OSWEN control bit (OSCCON<0>) has no effect when clock switching is disabled. It is held at `0' at all times. 8.5.2 OSCILLATOR SWITCHING SEQUENCE To perform a clock switch, the following basic sequence is required: 1. 2. 3. 4. 5. If required, read the COSC<2:0> bits to determine the current oscillator source. Perform the unlock sequence to allow a write to the OSCCON register high byte. Write the appropriate value to the NOSC<2:0> control bits for the new oscillator source. Perform the unlock sequence to allow a write to the OSCCON register low byte. Set the OSWEN bit to initiate the oscillator switch. After the basic sequence is completed, the system clock hardware responds as follows: 1. The clock switching hardware compares the COSC<2:0> status bits with the new value of the NOSC<2:0> control bits. If they are the same, the clock switch is a redundant operation. In this case, the OSWEN bit is cleared automatically and the clock switch is aborted. DS70318F-page 144 8.6 Fail-Safe Clock Monitor (FSCM) The Fail-Safe Clock Monitor (FSCM) allows the device to continue to operate even in the event of an oscillator failure. The FSCM function is enabled by programming. If the FSCM function is enabled, the LPRC internal oscillator runs at all times (except during Sleep mode) and is not subject to control by the Watchdog Timer. During an oscillator failure, the FSCM generates a clock failure trap event and switches the system clock over to the FRC oscillator. Then, the application program can either attempt to restart the oscillator or execute a controlled shutdown. The trap can be treated as a warm Reset by simply loading the Reset address into the oscillator fail trap vector. If the PLL multiplier is used to scale the system clock, the internal FRC is also multiplied by the same factor on clock failure. Essentially, the device switches to FRC with PLL on a clock failure. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 9.0 POWER-SAVING FEATURES Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 9. "Watchdog Timer and Power-Saving Modes" (DS70196) in the "dsPIC33F/PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. 9.2 Instruction-Based Power-Saving Modes The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices have two special power-saving modes that are entered through the execution of a special PWRSAV instruction. Sleep mode stops clock operation and halts all code execution. Idle mode halts the CPU and code execution, but allows peripheral modules to continue operation. The assembler syntax of the PWRSAV instruction is shown in Example 9-1. Note: SLEEP_MODE and IDLE_MODE are constants defined in the assembler include file for the selected device. Sleep and Idle modes can be exited as a result of an enabled interrupt, WDT time-out or a device Reset. When the device exits these modes, it is said to wake-up. 9.2.1 SLEEP MODE The following occur in Sleep mode: The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices provide the ability to manage power consumption by selectively managing clocking to the CPU and the peripherals. In general, a lower clock frequency and a reduction in the number of circuits being clocked constitutes lower consumed power. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices can manage power consumption in four different ways: * * * * Clock Frequency Instruction-Based Sleep and Idle modes Software-Controlled Doze mode Selective Peripheral Control in Software Combinations of these methods can be used to selectively tailor an application's power consumption while still maintaining critical application features, such as timing-sensitive communications. 9.1 Clock Frequency and Clock Switching The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices allow a wide range of clock frequencies to be selected under application control. If the system clock configuration is not locked, users can choose low-power or high-precision oscillators by simply changing the NOSC<2:0> bits (OSCCON<10:8>). The process of changing a system clock during operation, as well as limitations to the process, are discussed in more detail in Section 8.0 "Oscillator Configuration". EXAMPLE 9-1: * The system clock source is shut down. If an on-chip oscillator is used, it is turned off * The device current consumption is reduced to a minimum, provided that no I/O pin is sourcing current * The Fail-Safe Clock Monitor does not operate, since the system clock source is disabled * The LPRC clock continues to run in Sleep mode if the WDT is enabled * The WDT, if enabled, is automatically cleared prior to entering Sleep mode * Some device features or peripherals may continue to operate. This includes the items such as the input change notification on the I/O ports or peripherals that use an external clock input. * Any peripheral that requires the system clock source for its operation is disabled The device will wake-up from Sleep mode on any of these events: * Any interrupt source that is individually enabled * Any form of device Reset * A WDT time-out On wake-up from Sleep mode, the processor restarts with the same clock source that was active when Sleep mode was entered. PWRSAV INSTRUCTION SYNTAX PWRSAV #SLEEP_MODE PWRSAV #IDLE_MODE ; Put the device into SLEEP mode ; Put the device into IDLE mode (c) 2008-2012 Microchip Technology Inc. DS70318F-page 145 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 9.2.2 IDLE MODE The following occur in Idle mode: * The CPU stops executing instructions * The WDT is automatically cleared * The system clock source remains active. By default, all peripheral modules continue to operate normally from the system clock source, but can also be selectively disabled (see Section 9.4 "Peripheral Module Disable"). * If the WDT or FSCM is enabled, the LPRC also remains active The device will wake-up from Idle mode on any of these events: * Any interrupt that is individually enabled * Any device Reset * A WDT time-out On wake-up from Idle mode, the clock is reapplied to the CPU and instruction execution will begin (2-4 clock cycles later), starting with the instruction following the PWRSAV instruction, or the first instruction in the ISR. 9.2.3 INTERRUPTS COINCIDENT WITH POWER SAVE INSTRUCTIONS Any interrupt that coincides with the execution of a PWRSAV instruction is held off until entry into Sleep or Idle mode has completed. The device then wakes up from Sleep or Idle mode. 9.3 Doze Mode The preferred strategies for reducing power consumption are changing clock speed and invoking one of the power-saving modes. In some circumstances, this may not be practical. For example, it may be necessary for an application to maintain uninterrupted synchronous communication, even while it is doing nothing else. Reducing system clock speed can introduce communication errors, while using a power-saving mode can stop communications completely. Doze mode is a simple and effective alternative method to reduce power consumption while the device is still executing code. In this mode, the system clock continues to operate from the same source and at the same speed. Peripheral modules continue to be clocked at the same speed, while the CPU clock speed is reduced. Synchronization between the two clock domains is maintained, allowing the peripherals to access the SFRs while the CPU executes code at a slower rate. DS70318F-page 146 Doze mode is enabled by setting the DOZEN bit (CLKDIV<11>). The ratio between peripheral and core clock speed is determined by the DOZE<2:0> bits (CLKDIV<14:12>). There are eight possible configurations, from 1:1 to 1:128, with 1:1 being the default setting. Programs can use Doze mode to selectively reduce power consumption in event-driven applications. This allows clock-sensitive functions, such as synchronous communications, to continue without interruption while the CPU idles, waiting for something to invoke an interrupt routine. An automatic return to full-speed CPU operation on interrupts can be enabled by setting the ROI bit (CLKDIV<15>). By default, interrupt events have no effect on Doze mode operation. For example, suppose the device is operating at 20 MIPS and the CAN module has been configured for 500 kbps based on this device operating speed. If the device is placed in Doze mode with a clock frequency ratio of 1:4, the CAN module continues to communicate at the required bit rate of 500 kbps, but the CPU now starts executing instructions at a frequency of 5 MIPS. 9.4 Peripheral Module Disable The Peripheral Module Disable (PMD) registers provide a method to disable a peripheral module by stopping all clock sources supplied to that module. When a peripheral is disabled using the appropriate PMD control bit, the peripheral is in a minimum power consumption state. The control and status registers associated with the peripheral are also disabled, so writes to those registers will have no effect and read values will be invalid. A peripheral module is enabled only if both the associated bit in the PMD register is cleared and the peripheral is supported by the specific dsPIC(R) DSC variant. If the peripheral is present in the device, it is enabled in the PMD register by default. Note: If a PMD bit is set, the corresponding module is disabled after a delay of one instruction cycle. Similarly, if a PMD bit is cleared, the corresponding module is enabled after a delay of one instruction cycle (assuming the module control registers are already configured to enable module operation). (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 9-1: U-0 PMD1: PERIPHERAL MODULE DISABLE CONTROL REGISTER 1 U-0 -- -- R/W-0 T3MD R/W-0 T2MD R/W-0 T1MD U-0 -- R/W-0 U-0 (1) PWMMD -- bit 15 bit 8 R/W-0 U-0 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 I2C1MD -- U1MD -- SPI1MD -- -- ADCMD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-14 Unimplemented: Read as `0' bit 13 T3MD: Timer3 Module Disable bit 1 = Timer3 module is disabled 0 = Timer3 module is enabled bit 12 T2MD: Timer2 Module Disable bit 1 = Timer2 module is disabled 0 = Timer2 module is enabled bit 11 T1MD: Timer1 Module Disable bit 1 = Timer1 module is disabled 0 = Timer1 module is enabled bit 10 Unimplemented: Read as `0' bit 9 PWMMD: PWM Module Disable bit(1) 1 = PWM module is disabled 0 = PWM module is enabled bit 8 Unimplemented: Read as `0' bit 7 I2C1MD: I2C1 Module Disable bit 1 = I2C1 module is disabled 0 = I2C1 module is enabled bit 6 Unimplemented: Read as `0' bit 5 U1MD: UART1 Module Disable bit 1 = UART1 module is disabled 0 = UART1 module is enabled bit 4 Unimplemented: Read as `0' bit 3 SPI1MD: SPI1 Module Disable bit 1 = SPI1 module is disabled 0 = SPI1 module is enabled bit 2-1 Unimplemented: Read as `0' bit 0 ADCMD: ADC Module Disable bit 1 = ADC module is disabled 0 = ADC module is enabled Note 1: x = Bit is unknown Once the PWM module is re-enabled (PWMMD is set to `1' and then set to `0'), all PWM registers must be reinitialized. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 147 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 9-2: PMD2: PERIPHERAL MODULE DISABLE CONTROL REGISTER 2 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 -- -- -- -- -- -- IC2MD IC1MD bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 -- -- -- -- -- -- OC2MD OC1MD bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-10 Unimplemented: Read as `0' bit 9 IC2MD: Input Capture 2 Module Disable bit 1 = Input Capture 2 module is disabled 0 = Input Capture 2 module is enabled bit 8 IC1MD: Input Capture 1 Module Disable bit 1 = Input Capture 1 module is disabled 0 = Input Capture 1 module is enabled bit 7-2 Unimplemented: Read as `0' bit 1 OC2MD: Output Compare 2 Module Disable bit 1 = Output Compare 2 module is disabled 0 = Output Compare 2 module is enabled bit 0 OC1MD: Output Compare 1 Module Disable bit 1 = Output Compare 1 module is disabled 0 = Output Compare 1 module is enabled DS70318F-page 148 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 9-3: PMD3: PERIPHERAL MODULE DISABLE CONTROL REGISTER 3 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 -- -- -- -- -- CMPMD -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-11 Unimplemented: Read as `0' bit 10 CMPMD: Analog Comparator Module Disable bit 1 = Analog comparator module is disabled 0 = Analog comparator module is enabled bit 9-0 Unimplemented: Read as `0' REGISTER 9-4: x = Bit is unknown PMD4: PERIPHERAL MODULE DISABLE CONTROL REGISTER 4 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 -- -- -- -- REFOMD -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-4 Unimplemented: Read as `0' bit 3 REFOMD: Reference Clock Generator Module Disable bit 1 = Reference clock generator module is disabled 0 = Reference clock generator module is enabled bit 2-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 149 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 9-5: PMD6: PERIPHERAL MODULE DISABLE CONTROL REGISTER 6 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- -- PWM4MD PWM3MD PWM2MD PWM1MD bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-12 Unimplemented: Read as `0' bit 11 PWM4MD: PWM Generator 4 Module Disable bit 1 = PWM Generator 4 module is disabled 0 = PWM Generator 4 module is enabled bit 10 PWM3MD: PWM Generator 3 Module Disable bit 1 = PWM Generator 3 module is disabled 0 = PWM Generator 3 module is enabled bit 9 PWM2MD: PWM Generator 2 Module Disable bit 1 = PWM Generator 2 module is disabled 0 = PWM Generator 2 module is enabled bit 8 PWM1MD: PWM Generator 1 Module Disable bit 1 = PWM Generator 1 module is disabled 0 = PWM Generator 1 module is enabled bit 7-0 Unimplemented: Read as `0' DS70318F-page 150 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 9-6: PMD7: PERIPHERAL MODULE DISABLE CONTROL REGISTER 7 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- -- CMP4MD CMP3MD CMP2MD CMP1MD bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-12 Unimplemented: Read as `0' bit 11 CMP4MD: Analog Comparator 4 Module Disable bit 1 = Analog Comparator 4 module is disabled 0 = Analog Comparator 4 module is enabled bit 10 CMP3MD: Analog Comparator 3 Module Disable bit 1 = Analog Comparator 3 module is disabled 0 = Analog Comparator 3 module is enabled bit 9 CMP2MD: Analog Comparator 2 Module Disable bit 1 = Analog Comparator 2 module is disabled 0 = Analog Comparator 2 module is enabled bit 8 CMP1MD: Analog Comparator 1 Module Disable bit 1 = Analog Comparator 1 module is disabled 0 = Analog Comparator 1 module is enabled bit 7-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. x = Bit is unknown DS70318F-page 151 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 152 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 10.0 I/O PORTS Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 10. "I/O Ports" (DS70193) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. All of the device pins (except VDD, VSS, MCLR and OSC1/CLKI) are shared among the peripherals and the parallel I/O ports. All I/O input ports feature Schmitt Trigger inputs for improved noise immunity. 10.1 Parallel I/O (PIO) Ports Generally a parallel I/O port that shares a pin with a peripheral is subservient to the peripheral. The peripheral's output buffer data and control signals are provided to a pair of multiplexers. The multiplexers select whether the peripheral or the associated port FIGURE 10-1: has ownership of the output data and control signals of the I/O pin. The logic also prevents "loop through", in which a port's digital output can drive the input of a peripheral that shares the same pin. Figure 10-1 shows how ports are shared with other peripherals and the associated I/O pin to which they are connected. When a peripheral is enabled and the peripheral is actively driving an associated pin, the use of the pin as a general purpose output pin is disabled. The I/O pin can be read, but the output driver for the parallel port bit is disabled. If a peripheral is enabled, but the peripheral is not actively driving a pin, that pin can be driven by a port. All port pins have three registers directly associated with their operation as digital I/O. The data direction register (TRISx) determines whether the pin is an input or an output. If the data direction bit is `1', then the pin is an input. All port pins are defined as inputs after a Reset. Reads from the latch (LATx) read the latch. Writes to the latch write the latch. Reads from the port (PORTx) read the port pins, while writes to the port pins write the latch. Any bit and its associated data and control registers that are not valid for a particular device will be disabled. That means the corresponding LATx and TRISx registers and the port pin will read as zeros. When a pin is shared with another peripheral or function that is defined as an input only, it is nevertheless regarded as a dedicated port because there is no other competing source of outputs. BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE Peripheral Module Output Multiplexers Peripheral Input Data Peripheral Module Enable I/O Peripheral Output Enable 1 Peripheral Output Data 0 PIO Module WR TRIS Output Data 0 Read TRIS Data Bus 1 Output Enable D Q I/O Pin CK TRIS Latch D WR LAT + WR PORT Q CK Data Latch Read LAT Input Data Read PORT (c) 2008-2012 Microchip Technology Inc. DS70318F-page 153 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 10.2 Open-Drain Configuration In addition to the PORT, LAT and TRIS registers for data control, some digital-only port pins can also be individually configured for either digital or open-drain output. This is controlled by the Open-Drain Control register, ODCx, associated with each port. Setting any of the bits configures the corresponding pin to act as an open-drain output. The open-drain feature allows the generation of outputs higher than VDD (for example, 5V) on any desired 5V tolerant pins by using external pull-up resistors. The maximum open-drain voltage allowed is the same as the maximum VIH specification. Refer to "Pin Diagrams" for the available pins and their functionality. 10.3 Configuring Analog Port Pins The ADPCFG and TRIS registers control the operation of the Analog-to-Digital (A/D) port pins. The port pins that are to function as analog inputs must have their corresponding TRIS bit set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The ADPCFG register has a default value of 0x0000; therefore, all pins that share ANx functions are analog (not digital) by default. When the PORT register is read, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs will not convert an analog input. Analog levels on any pin defined as a digital input (including the ANx pins) can cause the input buffer to consume current that exceeds the device specifications. EQUATION 10-1: MOV MOV NOP BTSS 0xFF00, W0 W0, TRISBB PORTB, #13 DS70318F-page 154 10.4 I/O Port Write/Read Timing One instruction cycle is required between a port direction change or port write operation and a read operation of the same port. Typically, this instruction would be a NOP. An example is shown in Example 10-1. 10.5 Input Change Notification The input change notification function of the I/O ports allows the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices to generate interrupt requests to the processor in response to a Change-Of-State (COS) on selected input pins. This feature can detect input Change-Of-States even in Sleep mode, when the clocks are disabled. Depending on the device pin count, up to 30 external signals (CNx pin) can be selected (enabled) for generating an interrupt request on a Change-Of-State. Four control registers are associated with the CN module. The CNEN1 and CNEN2 registers contain the interrupt enable control bits for each of the CN input pins. Setting any of these bits enables a CN interrupt for the corresponding pins. Each CN pin also has a weak pull-up connected to it. The pull-ups act as a current source connected to the pin, and eliminate the need for external resistors when the push button or keypad devices are connected. The pull-ups are enabled separately using the CNPU1 and CNPU2 registers, which contain the control bits for each of the CN pins. Setting any of the control bits enables the weak pull-ups for the corresponding pins. Note: Pull-ups on change notification pins should always be disabled when the port pin is configured as a digital output. PORT WRITE/READ EXAMPLE ; ; ; ; Configure PORTB<15:8> as inputs and PORTB<7:0> as outputs Delay 1 cycle Next Instruction (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 10.6 Peripheral Pin Select Peripheral pin select configuration enables peripheral set selection and placement on a wide range of I/O pins. By increasing the pinout options available on a particular device, programmers can better tailor the microcontroller to their entire application, rather than trimming the application to fit the device. The peripheral pin select configuration feature operates over a fixed subset of digital I/O pins. Programmers can independently map the input and/or output of most digital peripherals to any one of these I/O pins. Peripheral pin select is performed in software, and generally does not require the device to be reprogrammed. Hardware safeguards are included that prevent accidental or spurious changes to the peripheral mapping, once it has been established. 10.6.1 AVAILABLE PINS The peripheral pin select feature is used with a range of up to 30 pins. The number of available pins depends on the particular device and its pin count. Pins that support the peripheral pin select feature include the designation "RPn" in their full pin designation, where "RP" designates a remappable peripheral and "n" is the remappable pin number. 10.6.2 10.6.2.1 The inputs of the peripheral pin select options are mapped on the basis of the peripheral. A control register associated with a peripheral dictates the pin it will be mapped to. The RPINRx registers are used to configure peripheral input mapping (see Register 10-1 through Register 10-14). Each register contains sets of 6-bit fields, with each set associated with one of the remappable peripherals. Programming a given peripheral's bit field with an appropriate 6-bit value maps the RPn pin with that value to that peripheral. For any given device, the valid range of values for any bit field corresponds to the maximum number of peripheral pin selections supported by the device. Figure 10-2 Illustrates remappable pin selection for U1RX input. Note: The association of a peripheral to a peripheral selectable pin is handled in two different ways, depending on whether an input or output is being mapped. For input mapping only, the Peripheral Pin Select (PPS) functionality does not have priority over the TRISx settings. Therefore, when configuring the RPx pin for input, the corresponding bit in the TRISx register must also be configured for input (i.e., set to `1'). FIGURE 10-2: CONTROLLING PERIPHERAL PIN SELECT Peripheral pin select features are controlled through two sets of Special Function Registers: one to map peripheral inputs and another one to map outputs. Because they are separately controlled, a particular peripheral's input and output (if the peripheral has both) can be placed on any selectable function pin without constraint. Input Mapping REMAPPABLE MUX INPUT FOR U1RX U1RXR<5:0> 0 RP0 1 RP1 2 U1RX Input to Peripheral RP2 33 RP33 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 155 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 10-1: SELECTABLE INPUT SOURCES (MAPS INPUT TO Function) Function Name Register Configuration Bits INT1 RPINR0 INT1R<5:0> External Interrupt 2 INT2 RPINR1 INT2R<5:0> Timer1 External Clock T1CK RPINR2 T1CKR<5:0> Timer2 External Clock T2CK RPINR3 T2CKR<5:0> Timer3 External Clock T3CK RPINR3 T3CKR<5:0> Input Capture 1 IC1 RPINR7 IC1R<5:0> Input Capture 2 IC2 RPINR7 IC2R<5:0> Input Name External Interrupt 1 Output Compare Fault A OCFA RPINR11 OCFAR<5:0> UART1 Receive U1RX RPINR18 U1RXR<5:0> UART1 Clear To Send U1CTS RPINR18 U1CTSR<5:0> SPI Data Input 1 SDI1 RPINR20 SDI1R<5:0> SPI Clock Input 1 SCK1 RPINR20 SCK1R<5:0> SPI Slave Select Input 1 SS1 RPINR21 SS1R<5:0> PWM Fault Input PWM1 FLT1 RPINR29 FLT1R<5:0> PWM Fault Input PWM2 FLT2 RPINR30 FLT2R<5:0> PWM Fault Input PWM3 FLT3 RPINR30 FLT3R<5:0> PWM Fault Input PWM4 FLT4 RPINR31 FLT4R<5:0> PWM Fault Input PWM5 FLT5 RPINR31 FLT5R<5:0> PWM Fault Input PWM6 FLT6 RPINR32 FLT6R<5:0> PWM Fault Input PWM7 FLT7 RPINR32 FLT7R<5:0> PWM Fault Input PWM8 FLT8 RPINR33 FLT8R<5:0> External Synchronization signal to PWM Master Time Base SYNCI1 RPINR33 SYNCI1R<5:0> External Synchronization signal to PWM Master Time Base SYNCI2 RPINR34 SYNCI2R<5:0> DS70318F-page 156 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 10.6.2.2 Output Mapping FIGURE 10-3: In contrast to inputs, the outputs of the peripheral pin select options are mapped on the basis of the pin. In this case, a control register associated with a particular pin dictates the peripheral output to be mapped. The RPORx registers are used to control output mapping. Like the RPINRx registers, each register contains sets of 6-bit fields, with each set associated with one RPn pin (see Register 10-15 through Register 10-31). The value of the bit field corresponds to one of the peripherals, and that peripheral's output is mapped to the pin (see Table 10-2 and Figure 10-3). The list of peripherals for output mapping also includes a null value of `00000' because of the mapping technique. This permits any given pin to remain unconnected from the output of any of the pin selectable peripherals. MULTIPLEXING OF REMAPPABLE OUTPUT FOR RPn RPORn<5:0> Default 0 U1TX Output Enable 3 U1RTS Output Enable 4 Output Enable OC2 Output Enable PWM4L Output Enable Default U1TX Output U1RTS Output 19 45 0 3 4 Output Data OC2 Output PWM4L Output TABLE 10-2: Function RPn 19 45 OUTPUT SELECTION FOR REMAPPABLE PIN (RPn) RPORn<5:0> Output Name NULL 000000 RPn tied to default port pin U1TX 000011 RPn tied to UART1 transmit U1RTS 000100 RPn tied to UART1 ready to send SDO1 000111 RPn tied to SPI1 data output SCK1 001000 RPn tied to SPI1 clock output SS1 001001 RPn tied to SPI1 slave select output OC1 010010 RPn tied to Output Compare 1 OC2 010011 RPn tied to Output Compare 2 SYNCO1 100101 RPn tied to external device synchronization signal via PWM master time base REFCLKO 100110 REFCLK output signal ACMP1 100111 RPn tied to Analog Comparator Output 1 ACMP2 101000 RPn tied to Analog Comparator Output 2 ACMP3 101001 RPn tied to Analog Comparator Output 3 ACMP4 101010 RPn tied to Analog Comparator Output 4 PWM4H 101100 RPn tied to PWM output pins associated with PWM Generator 4 PWM4L 101101 RPn tied to PWM output pins associated with PWM Generator 4 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 157 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 10.6.2.3 Virtual Pins dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices support four virtual RPn pins (RP32, RP33, RP34 and RP35), which are identical in functionality to all other RPn pins, with the exception of pinouts. These four pins are internal to the devices and are not connected to a physical device pin. These pins provide a simple way for inter-peripheral connection without utilizing a physical pin. For example, the output of the analog comparator can be connected to RP32 and the PWM Fault input can be configured for RP32 as well. This configuration allows the analog comparator to trigger PWM Faults without the use of an actual physical pin on the device. 10.6.3 CONTROLLING CONFIGURATION CHANGES Because peripheral remapping can be changed during run time, some restrictions on peripheral remapping are needed to prevent accidental configuration changes. dsPIC33F devices include three features to prevent alterations to the peripheral map: * Control register lock sequence * Continuous state monitoring * Configuration bit pin select lock 10.6.3.1 Control Register Lock Under normal operation, writes to the RPINRx and RPORx registers are not allowed. Attempted writes appear to execute normally, but the contents of the registers remain unchanged. To change these registers, they must be unlocked in hardware. The register lock is controlled by the IOLOCK bit (OSCCON<6>). Setting IOLOCK prevents writes to the control registers; clearing IOLOCK allows writes. Unlike the similar sequence with the oscillator's LOCK bit, IOLOCK remains in one state until changed. This allows all of the peripheral pin selects to be configured with a single unlock sequence followed by an update to all control registers, then locked with a second lock sequence. 10.6.3.2 Continuous State Monitoring In addition to being protected from direct writes, the contents of the RPINRx and RPORx registers are constantly monitored in hardware by shadow registers. If an unexpected change in any of the registers occurs (such as cell disturbances caused by ESD or other external events), a Configuration Mismatch Reset will be triggered. 10.6.3.3 Configuration Bit Pin Select Lock As an additional level of safety, the device can be configured to prevent many write session to the RPINRx and RPORx registers. The IOL1WAY (FOSC<5>) Configuration bit blocks the IOLOCK bit from being cleared after it has been set once. If IOLOCK remains set, the register unlock procedure will not execute and the Peripheral Pin Select Control registers cannot be written to. The only way to clear the bit and re-enable peripheral remapping is to perform a device Reset. In the default (unprogrammed) state, IOL1WAY is set, restricting users to one write session. Programming IOL1WAY allows user applications unlimited access (with the proper use of the unlock sequence) to the Peripheral Pin Select registers. To set or clear IOLOCK, a specific command sequence must be executed: 1. 2. 3. Write 0x46 to OSCCON<7:0>. Write 0x57 to OSCCON<7:0>. Clear (or set) IOLOCK as a single operation. Note: MPLAB(R) C30 provides built-in C language functions for unlocking the OSCCON register: __builtin_write_OSCCONL(value) __builtin_write_OSCCONH(value) See the MPLAB C30 Help files for more information. DS70318F-page 158 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 10.7 Peripheral Pin Select Registers The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices implement 34 registers for remappable peripheral configuration: Not all output remappable peripheral registers are implemented on all devices. See the specific register description for further details. * 15 Input Remappable Peripheral Registers * 19 Output Remappable Peripheral Registers Note: Input and output register values can only be changed if OSCCON = 0. See Section 10.6.3.1 "Control Register Lock" for a specific command sequence. REGISTER 10-1: RPINR0: PERIPHERAL PIN SELECT INPUT REGISTER 0 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 INT1R<5:0> bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 INT1R<5:0>: Assign External Interrupt 1 (INTR1) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. DS70318F-page 159 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-2: RPINR1: PERIPHERAL PIN SELECT INPUT REGISTER 1 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 INT2R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as `0' bit 5-0 INT2R<5:0>: Assign External Interrupt 2 (INTR2) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 DS70318F-page 160 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-3: RPINR3: PERIPHERAL PIN SELECT INPUT REGISTER 3 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 T3CKR<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 T2CKR<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 T3CKR<5:0>: Assign Timer3 External Clock (T3CK) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 T2CKR<5:0>: Assign Timer2 External Clock (T2CK) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 161 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-4: RPINR7: PERIPHERAL PIN SELECT INPUT REGISTER 7 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 IC2R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 IC1R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 IC2R<5:0>: Assign Input Capture 2 (IC2) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 IC1R<5:0>: Assign Input Capture 1 (IC1) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 DS70318F-page 162 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-5: RPINR11: PERIPHERAL PIN SELECT INPUT REGISTER 11 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 OCFAR<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as `0' bit 5-0 OCFAR<5:0>: Assign Output Capture A (OCFA) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 163 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-6: RPINR18: PERIPHERAL PIN SELECT INPUT REGISTER 18 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 U1CTSR<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 U1RXR<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 U1CTSR<5:0>: Assign UART1 Clear to Send (U1CTS) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 U1RXR<5:0>: Assign UART1 Receive (U1RX) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 DS70318F-page 164 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-7: RPINR20: PERIPHERAL PIN SELECT INPUT REGISTER 20 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 SCK1R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 SDI1R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 SCK1R<5:0>: Assign SPI1 Clock Input (SCK1IN) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 SDI1R<5:0>: Assign SPI1 Data Input (SDI1) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 165 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-8: RPINR21: PERIPHERAL PIN SELECT INPUT REGISTER 21 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 SS1R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as `0' bit 5-0 SS1R<5:0>: Assign SPI1 Slave Select Input (SS1IN) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 DS70318F-page 166 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-9: RPINR29: PERIPHERAL PIN SELECT INPUT REGISTER 29 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT1R<5:0> bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 FLT1R<5:0>: Assign PWM Fault Input 1 (FLT1) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. DS70318F-page 167 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-10: RPINR30: PERIPHERAL PIN SELECT INPUT REGISTER 30 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT3R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT2R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 FLT3R<5:0>: Assign PWM Fault Input 3 (FLT3) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 FLT2R<5:0>: Assign PWM Fault Input 2 (FLT2) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 DS70318F-page 168 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-11: RPINR31: PERIPHERAL PIN SELECT INPUT REGISTER 31 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT5R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT4R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 FLT5R<5:0>: Assign PWM Fault Input 5 (FLT5) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 FLT4R<5:0>: Assign PWM Fault Input 4 (FLT4) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 169 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-12: RPINR32: PERIPHERAL PIN SELECT INPUT REGISTER 32 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT7R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT6R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 FLT7R<5:0>: Assign PWM Fault Input 7 (FLT7) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 FLT6R<5:0>: Assign PWM Fault Input 6 (FLT6) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 DS70318F-page 170 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-13: RPINR33: PERIPHERAL PIN SELECT INPUT REGISTER 33 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 SYNCI1R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 FLT8R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 SYNCI1R<5:0>: Assign PWM Master Time Base External Synchronization Signal to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 bit 7-6 Unimplemented: Read as `0' bit 5-0 FLT8R<5:0>: Assign PWM Fault Input 8 (FLT8) to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 171 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-14: RPINR34: PERIPHERAL PIN SELECT INPUT REGISTER 34 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 -- -- R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 SYNCI2R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as `0' bit 5-0 SYNCI2R<5:0>: Assign PWM Master Time Base External Synchronization Signal to the Corresponding RPn Pin bits 111111 = Input tied to VSS 100011 = Input tied to RP35 100010 = Input tied to RP34 100001 = Input tied to RP33 100000 = Input tied to RP32 * * * 00000 = Input tied to RP0 REGISTER 10-15: RPOR0: PERIPHERAL PIN SELECT OUTPUT REGISTER 0 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP1R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP0R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP1R<5:0>: Peripheral Output Function is Assigned to RP1 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP0R<5:0>: Peripheral Output Function is Assigned to RP0 Output Pin bits (see Table 10-2 for peripheral function numbers) DS70318F-page 172 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-16: RPOR1: PERIPHERAL PIN SELECT OUTPUT REGISTER 1 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP3R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP2R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP3R<5:0>: Peripheral Output Function is Assigned to RP3 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP2R<5:0>: Peripheral Output Function is Assigned to RP2 Output Pin bits (see Table 10-2 for peripheral function numbers) REGISTER 10-17: RPOR2: PERIPHERAL PIN SELECT OUTPUT REGISTER 2 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP5R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP4R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP5R<5:0>: Peripheral Output Function is Assigned to RP5 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP4R<5:0>: Peripheral Output Function is Assigned to RP4 Output Pin bits (see Table 10-2 for peripheral function numbers) (c) 2008-2012 Microchip Technology Inc. DS70318F-page 173 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-18: RPOR3: PERIPHERAL PIN SELECT OUTPUT REGISTER 3 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP7R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP6R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP7R<5:0>: Peripheral Output Function is Assigned to RP7 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP6R<5:0>: Peripheral Output Function is Assigned to RP6 Output Pin bits (see Table 10-2 for peripheral function numbers) REGISTER 10-19: RPOR4: PERIPHERAL PIN SELECT OUTPUT REGISTER 4 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP9R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP8R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP9R<5:0>: Peripheral Output Function is Assigned to RP9 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP8R<5:0>: Peripheral Output Function is Assigned to RP8 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is not implemented in the dsPIC33FJ06GS101 device. DS70318F-page 174 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-20: RPOR5: PERIPHERAL PIN SELECT OUTPUT REGISTER 5 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP11R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP10R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP11R<5:0>: Peripheral Output Function is Assigned to RP11 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP10R<5:0>: Peripheral Output Function is Assigned to RP10 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is not implemented in the dsPIC33FJ06GS101 device. REGISTER 10-21: RPOR6: PERIPHERAL PIN SELECT OUTPUT REGISTER 6 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP13R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP12R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP13R<5:0>: Peripheral Output Function is Assigned to RP13 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP12R<5:0>: Peripheral Output Function is Assigned to RP12 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is not implemented in the dsPIC33FJ06GS101 device. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 175 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-22: RPOR7: PERIPHERAL PIN SELECT OUTPUT REGISTER 7 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP15R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP14R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP15R<5:0>: Peripheral Output Function is Assigned to RP15 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP14R<5:0>: Peripheral Output Function is Assigned to RP14 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is not implemented in the dsPIC33FJ06GS101 device. REGISTER 10-23: RPOR8: PERIPHERAL PIN SELECT OUTPUT REGISTER 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP17R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP16R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP17R<5:0>: Peripheral Output Function is Assigned to RP17 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP16R<5:0>: Peripheral Output Function is Assigned to RP16 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. DS70318F-page 176 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-24: RPOR9: PERIPHERAL PIN SELECT OUTPUT REGISTER 9 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP19R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP18R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP19R<5:0>: Peripheral Output Function is Assigned to RP19 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP18R<5:0>: Peripheral Output Function is Assigned to RP18 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. REGISTER 10-25: RPOR10: PERIPHERAL PIN SELECT OUTPUT REGISTER 10 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP21R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP20R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP21R<5:0>: Peripheral Output Function is Assigned to RP21 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP20R<5:0>: Peripheral Output Function is Assigned to RP20 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 177 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-26: RPOR11: PERIPHERAL PIN SELECT OUTPUT REGISTER 11 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP23R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP22R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP23R<5:0>: Peripheral Output Function is Assigned to RP23 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP22R<5:0>: Peripheral Output Function is Assigned to RP22 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. REGISTER 10-27: RPOR12: PERIPHERAL PIN SELECT OUTPUT REGISTER 12 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP25R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP24R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP25R<5:0>: Peripheral Output Function is Assigned to RP25 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP24R<5:0>: Peripheral Output Function is Assigned to RP24 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. DS70318F-page 178 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-28: RPOR13: PERIPHERAL PIN SELECT OUTPUT REGISTER 13 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP27R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP26R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP27R<5:0>: Peripheral Output Function is Assigned to RP27 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP26R<5:0>: Peripheral Output Function is Assigned to RP26 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. REGISTER 10-29: RPOR14: PERIPHERAL PIN SELECT OUTPUT REGISTER 14 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP29R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP28R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP29R<5:0>: Peripheral Output Function is Assigned to RP29 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP28R<5:0>: Peripheral Output Function is Assigned to RP28 Output Pin bits (see Table 10-2 for peripheral function numbers) Note 1: This register is implemented in dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 179 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 10-30: RPOR16: PERIPHERAL PIN SELECT OUTPUT REGISTER 16 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP33R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP32R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP33R<5:0>: Peripheral Output Function is Assigned to RP33 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP32R<5:0>: Peripheral Output Function is Assigned to RP32 Output Pin bits (see Table 10-2 for peripheral function numbers) REGISTER 10-31: RPOR17: PERIPHERAL PIN SELECT OUTPUT REGISTER 17 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP35R<5:0> bit 15 bit 8 U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RP34R<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-8 RP35R<5:0>: Peripheral Output Function is Assigned to RP35 Output Pin bits (see Table 10-2 for peripheral function numbers) bit 7-6 Unimplemented: Read as `0' bit 5-0 RP34R<5:0>: Peripheral Output Function is Assigned to RP34 Output Pin bits (see Table 10-2 for peripheral function numbers) DS70318F-page 180 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 11.0 TIMER1 The unique features of Timer1 allow it to be used for Real-Time Clock (RTC) applications. A block diagram of Timer1 is shown in Figure 11-1. Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 11. "Timers" (DS70205) in the "dsPIC33F/PIC24H Family Reference Manual", which is available from the Microchip web site (www.microchip.com). The Timer1 module can operate in one of the following modes: * * * * In Timer and Gated Timer modes, the input clock is derived from the internal instruction cycle clock (FCY). In Synchronous and Asynchronous Counter modes, the input clock is derived from the external clock input at the T1CK pin. 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The Timer modes are determined by the following bits: * Timer Clock Source Control bit (TCS): T1CON<1> * Timer Synchronization Control bit (TSYNC): T1CON<2> * Timer Gate Control bit (TGATE): T1CON<6> The Timer1 module is a 16-bit timer, which can serve as a time counter for the Real-Time Clock (RTC), or operate as a free-running interval timer/counter. The timer control bit settings for different operating modes are given in the Table 11-1. The Timer1 module has the following unique features over other timers: TABLE 11-1: * Can be operated from the low-power 32 kHz crystal oscillator available on the device * Can be operated in Asynchronous Counter mode from an external clock source * Optionally, the external clock input (T1CK) can be synchronized to the internal device clock and the clock synchronization is performed after the prescaler FIGURE 11-1: Timer mode Gated Timer mode Synchronous Counter mode Asynchronous Counter mode TIMER MODE SETTINGS Mode TCS TGATE TSYNC Timer 0 0 x Gated Timer 0 1 x Synchronous Counter 1 x 1 Asynchronous Counter 1 x 0 16-BIT TIMER1 MODULE BLOCK DIAGRAM Falling Edge Detect Gate Sync 1 Set T1IF Flag 0 FCY Prescaler (/n) 10 TCKPS<1:0> 00 TMR1 Reset TGATE 0 x1 T1CK Prescaler (/n) Sync TSYNC TCKPS<1:0> (c) 2008-2012 Microchip Technology Inc. Equal Comparator 1 TGATE TCS PR1 DS70318F-page 181 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 11-1: T1CON: TIMER1 CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON -- TSIDL -- -- -- -- -- bit 15 bit 8 U-0 R/W-0 -- TGATE R/W-0 R/W-0 TCKPS<1:0> U-0 R/W-0 R/W-0 U-0 -- TSYNC TCS -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 TON: Timer1 On bit 1 = Starts 16-bit Timer1 0 = Stops 16-bit Timer1 bit 14 Unimplemented: Read as `0' bit 13 TSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-7 Unimplemented: Read as `0' bit 6 TGATE: Timer1 Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation enabled 0 = Gated time accumulation disabled bit 5-4 TCKPS<1:0> Timer1 Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3 Unimplemented: Read as `0' bit 2 TSYNC: Timer1 External Clock Input Synchronization Select bit When TCS = 1: 1 = Synchronize external clock input 0 = Do not synchronize external clock input When TCS = 0: This bit is ignored. bit 1 TCS: Timer1 Clock Source Select bit 1 = External clock from T1CK pin (on the rising edge) 0 = Internal clock (FCY) bit 0 Unimplemented: Read as `0' DS70318F-page 182 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 12.0 TIMER2/3 FEATURES Timer2 is a Type B timer that offers the following major features: Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 11. "Timers" (DS70205) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). * A Type B timer can be concatenated with a Type C timer to form a 32-bit timer * External clock input (TxCK) is always synchronized to the internal device clock and the clock synchronization is performed after the prescaler. Figure 12-1 shows a block diagram of the Type B timer. Timer3 is a Type C timer that offers the following major features: * A Type C timer can be concatenated with a Type B timer to form a 32-bit timer * The external clock input (TxCK) is always synchronized to the internal device clock and the clock synchronization is performed before the prescaler 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. A block diagram of the Type C timer is shown in Figure 12-2. Note: FIGURE 12-1: Timer3 is not available on all devices. TYPE B TIMER BLOCK DIAGRAM (x = 2) Gate Sync FCY Falling Edge Detect 1 00 TCKPS<1:0> Prescaler (/n) 0 10 Prescaler (/n) Sync TMRx x1 Comparator TxCK TCKPS<1:0> Set TxIF Flag Reset TGATE Equal TGATE TCS PRx FIGURE 12-2: TYPE C TIMER BLOCK DIAGRAM (x = 3) Gate Sync Falling Edge Detect Prescaler (/n) FCY 00 Prescaler (/n) TMRx Comparator TGATE Equal TGATE TCS (c) 2008-2012 Microchip Technology Inc. Reset x1 TxCK TCKPS<1:0> Set TxIF Flag 0 10 TCKPS<1:0> Sync 1 PRx DS70318F-page 183 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 The Timer2/3 module can operate in one of the following modes: * Timer mode * Gated Timer mode * Synchronous Counter mode In Timer and Gated Timer modes, the input clock is derived from the internal instruction cycle clock (FCY). In Synchronous Counter mode, the input clock is derived from the external clock input at the TxCK pin. The timer modes are determined by the following bits: * TCS (TxCON<1>): Timer Clock Source Control bit * TGATE (TxCON<6>): Timer Gate Control bit When configured for 32-bit operation, only the Type B Timer Control (TxCON) register bits are required for setup and control while the Type C Timer Control register bits are ignored (except the TSIDL bit). For interrupt control, the combined 32-bit timer uses the interrupt enable, interrupt flag and interrupt priority control bits of the Type C timer. The interrupt control and status bits for the Type B timer are ignored during 32-bit timer operation. The Timer2 and Timer 3 that can be combined to form a 32-bit timer are listed in Table 12-2. TABLE 12-2: Timer control bit settings for different operating modes are given in the Table 12-1. TABLE 12-1: TIMER MODE SETTINGS Mode TCS TGATE Timer 0 0 Gated Timer 0 1 Synchronous Counter 1 x 12.1 16-bit Operation 1. 2. 3. 4. 5. 6. 12.2 32-bit Operation A 32-bit timer module can be formed by combining a Type B and a Type C 16-bit timer module. For 32-bit timer operation, the T32 control bit in the Type B Timer Control (TxCON<3>) register must be set. The Type C timer holds the most significant word (msw) and the Type B timer holds the least significant word (lsw) for 32-bit operation. DS70318F-page 184 Type C Timer (msw) Timer2 Timer3 To configure the features of Timer2/3 for 32-bit operation: 1. 2. 3. Type B Timer (lsw) A block diagram representation of the 32-bit timer module is shown in Figure 12-3. The 32-timer module can operate in one of the following modes: * Timer mode * Gated Timer mode * Synchronous Counter mode To configure any of the timers for individual 16-bit operation: Clear the T32 bit corresponding to that timer. Select the timer prescaler ratio using the TCKPS<1:0> bits. Set the Clock and Gating modes using the TCS and TGATE bits. Load the timer period value into the PRx register. If interrupts are required, set the interrupt enable bit, TxIE. Use the priority bits, TxIP<2:0>, to set the interrupt priority. Set the TON bit. 32-BIT TIMER 4. 5. 6. Set the T32 control bit. Select the prescaler ratio for Timer2 using the TCKPS<1:0> bits. Set the Clock and Gating modes using the corresponding TCS and TGATE bits. Load the timer period value. PR3 contains the most significant word of the value, while PR2 contains the least significant word. If interrupts are required, set the interrupt enable bit, T3IE. Use the priority bits, T3IP<2:0>, to set the interrupt priority. While Timer2 controls the timer, the interrupt appears as a Timer3 interrupt. Set the corresponding TON bit. The timer value at any point is stored in the register pair, TMR3:TMR2, which always contains the most significant word of the count, while TMR2 contains the least significant word. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 12-3: 32-BIT TIMER BLOCK DIAGRAM Gate Sync Falling Edge Detect 1 Set TyIF Flag PRy PRx 0 Equal Comparator FCY Prescaler (/n) lsw 00 TCKPS<1:0> Prescaler (/n) TGATE 10 Sync TMRx(1) msw TMRy(2) Reset x1 TxCK TCKPS<1:0> TGATE TMRyHLD TCS Data Bus <15:0> Note 1: Timerx is a Type B Timer (x = 2). 2: Timery is a Type C Timer (y = 3). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 185 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 12-1: TxCON: TIMER CONTROL REGISTER (x = 2) R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON -- TSIDL -- -- -- -- -- bit 15 bit 8 U-0 R/W-0 -- TGATE R/W-0 R/W-0 TCKPS<1:0> R/W-0 U-0 R/W-0 U-0 T32 -- TCS -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 TON: Timerx On bit When T32 = 1 (in 32-bit Timer mode): 1 = Starts 32-bit TMRx:TMRy timer pair 0 = Stops 32-bit TMRx:TMRy timer pair When T32 = 0 (in 16-bit Timer mode): 1 = Starts 16-bit timer 0 = Stops 16-bit timer bit 14 Unimplemented: Read as `0' bit 13 TSIDL: Stop in Idle Mode bit 1 = Discontinue timer operation when device enters Idle mode 0 = Continue timer operation in Idle mode bit 12-7 Unimplemented: Read as `0' bit 6 TGATE: Timerx Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation enabled 0 = Gated time accumulation disabled bit 5-4 TCKPS<1:0>: Timerx Input Clock Prescale Select bits 11 = 1:256 prescale value 10 = 1:64 prescale value 01 = 1:8 prescale value 00 = 1:1 prescale value bit 3 T32: 32-bit Timerx Mode Select bit 1 = TMRx and TMRy form a 32-bit timer 0 = TMRx and TMRy form separate 16-bit timer bit 2 Unimplemented: Read as `0' bit 1 TCS: Timerx Clock Source Select bit 1 = External clock from TxCK pin 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as `0' DS70318F-page 186 x = Bit is unknown (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 12-2: R/W-0 TyCON: TIMER CONTROL REGISTER (y = 3) U-0 TON(2) -- R/W-0 (1) TSIDL U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- bit 15 bit 8 U-0 R/W-0 -- TGATE(2) R/W-0 R/W-0 TCKPS<1:0>(2) U-0 -- U-0 R/W-0 U-0 -- TCS(2) -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15 TON: Timery On bit(2) 1 = Starts 16-bit Timery 0 = Stops 16-bit Timery bit 14 Unimplemented: Read as `0' bit 13 TSIDL: Stop in Idle Mode bit(1) 1 = Discontinue timer operation when device enters Idle mode 0 = Continue timer operation in Idle mode bit 12-7 Unimplemented: Read as `0' bit 6 TGATE: Timery Gated Time Accumulation Enable bit(2) When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation enabled 0 = Gated time accumulation disabled bit 5-4 TCKPS<1:0>: Timery Input Clock Prescale Select bits(2) 11 = 1:256 prescale value 10 = 1:64 prescale value 01 = 1:8 prescale value 00 = 1:1 prescale value bit 3-2 Unimplemented: Read as `0' bit 1 TCS: Timery Clock Source Select bit(2) 1 = External clock from TxCK pin 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as `0' Note 1: 2: x = Bit is unknown When 32-bit timer operation is enabled (T32 = 1) in the Timer Control register (TxCON<3>), the TSIDL bit must be cleared to operate the 32-bit timer in Idle mode. When the 32-bit timer operation is enabled (T32 = 1) in the Timer Control (TxCON<3>) register, these bits have no effect. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 187 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 188 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 13.0 INPUT CAPTURE Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 12. "Input Capture" (DS70198) in the "dsPIC33F/ PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The input capture module is useful in applications requiring frequency (period) and pulse measurement. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices support up to two input capture channels. FIGURE 13-1: The input capture module captures the 16-bit value of the selected Time Base register when an event occurs at the ICx pin. The events that cause a capture event are listed below in three categories: * Simple Capture Event modes: - Capture timer value on every falling edge of input at ICx pin - Capture timer value on every rising edge of input at ICx pin * Capture timer value on every edge (rising and falling) * Prescaler Capture Event modes: - Capture timer value on every 4th rising edge of input at ICx pin - Capture timer value on every 16th rising edge of input at ICx pin Each input capture channel can select one of the two 16-bit timers (Timer2 or Timer3) for the time base. The selected timer can use either an internal or external clock. Other operational features include: * Device wake-up from capture pin during CPU Sleep and Idle modes * Interrupt on input capture event * 4-word FIFO buffer for capture values - Interrupt optionally generated after 1, 2, 3 or 4 buffer locations are filled * Use of input capture to provide additional sources of external interrupts INPUT CAPTURE BLOCK DIAGRAM From 16-bit Timers TMR2 TMR3 16 16 1 Edge Detection Logic and Clock Synchronizer Prescaler Counter (1, 4, 16) ICx Pin ICM<2:0> (ICxCON<2:0>) Mode Select ICTMR (ICxCON<7>) FIFO 3 0 FIFO R/W Logic ICOV, ICBNE (ICxCON<4:3>) ICxBUF ICxI<1:0> ICxCON Interrupt Logic System Bus Set Flag ICxIF (in IFSx Register) Note 1: An `x' in a signal, register or bit name denotes the number of the capture channel. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 189 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 13.1 Input Capture Register REGISTER 13-1: ICxCON: INPUT CAPTURE x CONTROL REGISTER (x = 1, 2) U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 -- -- ICSIDL -- -- -- -- -- bit 15 bit 8 R/W-0 R/W-0 ICTMR R/W-0 ICI<1:0> R-0, HC R-0, HC ICOV ICBNE R/W-0 R/W-0 R/W-0 ICM<2:0> bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13 ICSIDL: Input Capture Module Stop in Idle Control bit 1 = Input capture module halts in CPU Idle mode 0 = Input capture module continues to operate in CPU Idle mode bit 12-8 Unimplemented: Read as `0' bit 7 ICTMR: Input Capture Timer Select bits 1 = TMR2 contents are captured on capture event 0 = TMR3 contents are captured on capture event bit 6-5 ICI<1:0>: Select Number of Captures per Interrupt bits 11 = Interrupt on every fourth capture event 10 = Interrupt on every third capture event 01 = Interrupt on every second capture event 00 = Interrupt on every capture event bit 4 ICOV: Input Capture Overflow Status Flag bit (read-only) 1 = Input capture overflow occurred 0 = No input capture overflow occurred bit 3 ICBNE: Input Capture Buffer Empty Status bit (read-only) 1 = Input capture buffer is not empty, at least one more capture value can be read 0 = Input capture buffer is empty bit 2-0 ICM<2:0>: Input Capture Mode Select bits 111 = Input capture functions as interrupt pin only when device is in Sleep or Idle mode. Rising edge detect-only, all other control bits are not applicable. 110 = Unused (module disabled) 101 = Capture mode, every 16th rising edge 100 = Capture mode, every 4th rising edge 011 = Capture mode, every rising edge 010 = Capture mode, every falling edge 001 = Capture mode, every edge (rising and falling). ICI<1:0> bits do not control interrupt generation for this mode. 000 = Input capture module turned off DS70318F-page 190 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 14.0 OUTPUT COMPARE Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 13. "Output Compare" (DS70209) in the "dsPIC33F/ PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. FIGURE 14-1: The output compare module can select either Timer2 or Timer3 for its time base. The module compares the value of the timer with the value of one or two Compare registers depending on the operating mode selected. The state of the output pin changes when the timer value matches the Compare register value. The output compare module generates either a single output pulse, or a sequence of output pulses, by changing the state of the output pin on the compare match events. The output compare module can also generate interrupts on compare match events. The output compare module has multiple operating modes: * * * * * * * Active-Low One-Shot mode Active-High One-Shot mode Toggle mode Delayed One-Shot mode Continuous Pulse mode PWM mode without Fault Protection PWM mode with Fault Protection OUTPUT COMPARE MODULE BLOCK DIAGRAM Set Flag bit OCxIF OCxRS Output Logic OCxR 3 16 1 OCx Output Enable OCM<2:0> Mode Select Comparator 0 S Q R OCTSEL 0 1 TMR2 Rollover TMR3 Rollover OCFA 16 TMR2 TMR3 Note: An `x' in a signal, register or bit name denotes the number of the output compare channels. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 191 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 14.1 Output Compare Modes application must disable the associated timer when writing to the Output Compare Control registers to avoid malfunctions. Configure the Output Compare modes by setting the appropriate Output Compare Mode (OCM<2:0>) bits in the Output Compare Control (OCxCON<2:0>) register. Table 14-1 lists the different bit settings for the Output Compare modes. Figure 14-2 illustrates the output compare operation for various modes. The user TABLE 14-1: Note: Refer to Section 13. "Output Compare" (DS70209) in the "dsPIC33F/PIC24H Family Reference Manual" for OCxR and OCxRS register restrictions. OUTPUT COMPARE MODES OCM<2:0> Mode OCx Pin Initial State 111 PWM with Fault Protection 110 PWM without Fault Protection 101 100 011 010 001 Continuous Pulse Delayed One-Shot Toggle Active-High One-Shot Active-Low One-Shot `0', if OCxR is zero `1', if OCxR is non-zero `0', if OCxR is zero `1', if OCxR is non-zero 0 0 Current output is maintained 1 0 000 Module Disabled Controlled by GPIO register FIGURE 14-2: OCx Interrupt Generation OCFA falling edge for OC1 to OC4 No interrupt OCx falling edge OCx falling edge OCx rising and falling edge OCx falling edge OCx rising edge -- OUTPUT COMPARE OPERATION Output Compare Mode Enabled Timer is Reset on Period Match OCxRS TMRy OCxR Active-Low One-Shot (OCM = 001) Active-High One-Shot (OCM = 010) Toggle (OCM = 011) Delayed One-Shot (OCM = 100) Continuous Pulse (OCM = 101) PWM (OCM = 110 or 111) DS70318F-page 192 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 14-1: OCxCON: OUTPUT COMPARE x CONTROL REGISTER (x = 1, 2) U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 -- -- OCSIDL -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 R-0, HC R/W-0 -- -- -- OCFLT OCTSEL R/W-0 R/W-0 R/W-0 OCM<2:0> bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-14 Unimplemented: Read as `0' bit 13 OCSIDL: Stop Output Compare in Idle Mode Control bit 1 = Output Compare x halts in CPU Idle mode 0 = Output Compare x continues to operate in CPU Idle mode x = Bit is unknown bit 12-5 Unimplemented: Read as `0' bit 4 OCFLT: PWM Fault Condition Status bit 1 = PWM Fault condition has occurred (cleared in hardware only) 0 = No PWM Fault condition has occurred (this bit is only used when OCM<2:0> = 111) bit 3 OCTSEL: Output Compare Timer Select bit 1 = Timer3 is the clock source for Compare x 0 = Timer2 is the clock source for Compare x bit 2-0 OCM<2:0>: Output Compare Mode Select bits 111 = PWM mode on OCx, Fault pin enabled 110 = PWM mode on OCx, Fault pin disabled 101 = Initialize OCx pin low, generate continuous output pulses on OCx pin 100 = Initialize OCx pin low, generate single output pulse on OCx pin 011 = Compare event toggles OCx pin 010 = Initialize OCx pin high, compare event forces OCx pin low 001 = Initialize OCx pin low, compare event forces OCx pin high 000 = Output compare channel is disabled (c) 2008-2012 Microchip Technology Inc. DS70318F-page 193 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 194 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 15.0 HIGH-SPEED PWM Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 43. "High- Speed PWM" (DS70323) in the "dsPIC33F/ PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The high-speed PWM module on the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 devices supports a wide variety of PWM modes and output formats. This PWM module is ideal for power conversion applications, such as: * * * * * * * AC/DC Converters DC/DC Converters Power Factor Correction (PFC) Uninterruptible Power Supply (UPS) Inverters Battery Chargers Digital Lighting 15.1 Features Overview The high-speed PWM module incorporates the following features: * 2-4 PWM generators with 4-8 outputs * Individual time base and duty cycle for each of the eight PWM outputs * Dead time for rising and falling edges: * Duty cycle resolution of 1.04 ns * Dead-time resolution of 1.04 ns * Phase shift resolution of 1.04 ns (c) 2008-2012 Microchip Technology Inc. * Frequency resolution of 1.04 ns * PWM modes supported: - Standard Edge-Aligned - True Independent Output - Complementary - Center-Aligned - Push-Pull - Multiphase - Variable Phase - Fixed Off-Time - Current Reset - Current-Limit * Independent Fault/Current-Limit inputs for each of the eight PWM outputs * Output override control * Special Event Trigger * PWM capture feature * Prescaler for input clock * Dual trigger from PWM to ADC * PWMxH, PWMxL output pin swapping * PWM4H, PWM4L pins remappable * On-the-fly PWM frequency, duty cycle and phase shift changes * Disabling of Individual PWM generators to reduce power consumption * Leading-Edge Blanking (LEB) functionality Note: Duty cycle, dead-time, phase shift and frequency resolution is 8.32 ns in Center-Aligned PWM mode. Figure 15-1 conceptualizes the PWM module in a simplified block diagram. Figure 15-2 illustrates how the module hardware is partitioned for each PWM output pair for the Complementary PWM mode. Each functional unit of the PWM module is discussed in subsequent sections. The PWM module contains four PWM generators. The module has up to eight PWM output pins: PWM1H, PWM1L, PWM2H, PWM2L, PWM3H, PWM3L, PWM4H and PWM4L. For complementary outputs, these eight I/O pins are grouped into H/L pairs. DS70318F-page 195 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 15.2 Feature Description The PWM module is designed for applications that require: * High-resolution at high PWM frequencies * The ability to drive Standard, Edge-Aligned, Center-Aligned Complementary mode, and Push-Pull mode outputs * The ability to create multiphase PWM outputs For Center-Aligned mode, the duty cycle, period phase and dead-time resolutions will be 8.32 ns. Two common, medium power converter topologies are push-pull and half-bridge. These designs require the PWM output signal to be switched between alternate pins, as provided by the Push-Pull PWM mode. Phase-shifted PWM describes the situation where each PWM generator provides outputs, but the phase relationship between the generator outputs is specifiable and changeable. Multiphase PWM is often used to improve DC/DC converter load transient response, and reduce the size of output filter capacitors and inductors. Multiple DC/ DC converters are often operated in parallel, but phase-shifted in time. A single PWM output operating at 250 kHz has a period of 4 s, but an array of four PWM channels, staggered by 1 s each, yields an effective switching frequency of 1 MHz. Multiphase PWM applications typically use a fixed-phase relationship. Variable phase PWM is useful in Zero Voltage Transition (ZVT) power converters. Here, the PWM duty cycle is always 50%, and the power flow is controlled by varying the relative phase shift between the two PWM generators. DS70318F-page 196 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 15-1: SIMPLIFIED CONCEPTUAL BLOCK DIAGRAM OF HIGH-SPEED PWM PWMCONx Pin and Mode Control LEBCONx Control for Blanking External Input Signals TRGCONx ADC Trigger Control Dead-Time Control ALTDTRx, DTRx PWM Enable and Mode Control PTCON MDC Master Duty Cycle Register PDC1 MUX Latch PWM GEN 1 Comparator Channel 1 Dead-Time Generator PWM1H Channel 2 Dead-Time Generator PWM2H PWM1L Timer Phase 16-bit Data Bus Latch PWM GEN 2 Comparator Timer Phase PDC3 MUX Latch PWM GEN 3 Comparator Timer Phase PWM2L Fault CLMT Override Logic MUX PWM User, Current-Limit and Fault Override and Routing Logic PDC2 Channel 3 Dead-Time Generator PWM3H PWM3L PDC4 MUX PWM GEN 4 Latch PWM4H(1) Channel 4 Dead-Time Generator Comparator PWM4L(1) Timer Phase PTPER Timer Period Special Event Postscaler Comparator IOCONx FLTX(1) SYNCO(1) SYNCIX(1) External Time Base Synchronization PTMR SEVTCMP Fault Control Logic Master Time Base Special Event Trigger Special Event Comparison Value Pin Override Control FCLCONx Fault Mode and Pin Control Note 1: These pins are remappable. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 197 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 15-2: PARTITIONED OUTPUT PAIR, COMPLEMENTARY PWM MODE Phase Offset TMR < PDC PWM Dead-Time Timer/Counter Override Logic Logic M U X PWMXH M U X PWMXL Duty Cycle Comparator PWM Duty Cycle Register Channel Override Values Fault Override Values Fault Pin 15.3 Fault Pin Assignment Logic Fault Active Control Registers The following registers control the operation of the high-speed PWM module. * * * * * * * * * * * * * * * * * * * PTCON: PWM Time Base Control Register PTCON2: PWM Clock Divider Select Register PTPER: PWM Master Time Base Register SEVTCMP: PWM Special Event Compare Register MDC: PWM Master Duty Cycle Register PWMCONx: PWMx Control Register PDCx: PWMx Generator Duty Cycle Register PHASEx: PWMx Primary Phase Shift Register (provides the local time base period for PWMxH) DTRx: PWMx Dead-Time Register ALTDTRx: PWMx Alternate Dead-Time Register SDCx: PWMx Secondary Duty Cycle Register SPHASEx: PWMx Secondary Phase Shift Register (provides the local time base for PWMxL) TRGCONx: PWMx Trigger Control Register IOCONx: PWMx I/O Control Register FCLCONx: PWMx Fault Current-Limit Control Register TRIGx: PWMx Primary Trigger Compare Value Register STRIGx: PWMx Secondary Trigger Compare Value Register LEBCONx: Leading-Edge Blanking Control Register PWMCAPx: Primary PWMx Time Base Capture Register DS70318F-page 198 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-1: PTCON: PWM TIME BASE CONTROL REGISTER R/W-0 PTEN bit 15 U-0 -- R/W-0 PTSIDL HS/HC-0 SESTAT R/W-0 SEIEN R/W-0 EIPU(1) R/W-0 SYNCEN(1) bit 7 U-0 R/W-0 R/W-0 R/W-0 R/W-0 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7 bit 6 bit 5-4 bit 3-0 Note 1: R/W-0 R/W-0 SEVTPS<3:0>(1) bit 0 Legend: R = Readable bit -n = Value at POR bit 15 SYNCSRC<1:0>(1) -- R/W-0 R/W-0 (1) SYNCPOL SYNCOEN(1) bit 8 HC = Hardware Clearable bit W = Writable bit `1' = Bit is set HS = Hardware Settable bit U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown PTEN: PWM Module Enable bit 1 = PWM module is enabled 0 = PWM module is disabled Unimplemented: Read as `0' PTSIDL: PWM Time Base Stop in Idle Mode bit 1 = PWM time base halts in CPU Idle mode 0 = PWM time base runs in CPU Idle mode SESTAT: Special Event Interrupt Status bit 1 = Special event interrupt is pending 0 = Special event interrupt is not pending SEIEN: Special Event Interrupt Enable bit 1 = Special event interrupt is enabled 0 = Special event interrupt is disabled EIPU: Enable Immediate Period Updates bit(1) 1 = Active Period register is updated immediately 0 = Active Period register updates occur on PWM cycle boundaries SYNCPOL: Synchronization Input/Output Polarity bit(1) 1 = SYNCIx and SYNCO polarity is inverted (active-low) 0 = SYNCIx and SYNCO are active-high SYNCOEN: Primary Time Base Sync Enable bit(1) 1 = SYNCO output is enabled 0 = SYNCO output is disabled SYNCEN: External Time Base Synchronization Enable bit(1) 1 = External synchronization of primary time base is enabled 0 = External synchronization of primary time base is disabled Unimplemented: Read as `0' SYNCSRC<1:0>: Synchronous Source Selection bits(1) 11 = Reserved 10 = Reserved 01 = SYNCI2 00 = SYNCI1 SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits(1) 1111 = 1:16 Postscaler generates a Special Event Trigger trigger on every sixteenth compare match event * * * 0001 = 1:2 Postscaler generates a Special Event Trigger on every second compare match event 0000 = 1:1 Postscaler generates a Special Event Trigger on every compare match event These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user application must program the period register with a value that is slightly larger than the expected period of the external synchronization input signal. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 199 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-2: PTCON2: PWM CLOCK DIVIDER SELECT REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 U-0 -- -- U-0 -- U-0 -- U-0 R/W-0 R/W-0 R/W-0 (1) -- PCLKDIV<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as `0' bit 2-0 PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(1) 111 = Reserved 110 = Divide by 64, maximum PWM timing resolution 101 = Divide by 32, maximum PWM timing resolution 100 = Divide by 16, maximum PWM timing resolution 011 = Divide by 8, maximum PWM timing resolution 010 = Divide by 4, maximum PWM timing resolution 001 = Divide by 2, maximum PWM timing resolution 000 = Divide by 1, maximum PWM timing resolution (Power-on default) Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. REGISTER 15-3: R/W-1 PTPER: PWM MASTER TIME BASE REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PTPER <15:8> bit 15 bit 8 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 PTPER <7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-0 x = Bit is unknown PTPER<15:0>: PWM Master Time Base (PMTMR) Period Value bits Note 1: The minimum value that can be loaded into the PTPER register is 0x0010 and the maximum value is 0xFFF8. DS70318F-page 200 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-4: R/W-0 SEVTCMP: PWM SPECIAL EVENT COMPARE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SEVTCMP <12:5> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SEVTCMP <4:0> U-0 U-0 U-0 -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-3 SEVTCMP<12:0>: Special Event Compare Count Value bits bit 2-0 Unimplemented: Read as `0' REGISTER 15-5: R/W-0 x = Bit is unknown MDC: PWM MASTER DUTY CYCLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MDC<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 MDC<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-0 x = Bit is unknown MDC<15:0>: Master PWM Duty Cycle Value bits Note 1: The smallest pulse width that can be generated on the PWM output corresponds to a value of 0x0009, while the maximum pulse width generated corresponds to a value of Period - 0x0008. 2: As the duty cycle gets closer to 0% or 100% of the PWM period (0 ns-40 ns, depending on the mode of operation), the PWM duty cycle resolution will degrade from 1 LSB to 3 LSB. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 201 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-6: PWMCONx: PWMx CONTROL REGISTER HS/HC-0 HS/HC-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTSTAT(1) CLSTAT(1) TRGSTAT FLTIEN CLIEN TRGIEN ITB(3) MDCS(3) bit 15 bit 8 R/W-0 R/W-0 DTC<1:0> U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 -- -- -- CAM(2,3) XPRES(4) IUE bit 7 bit 0 Legend: HC = Hardware Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 FLTSTAT: Fault Interrupt Status bit(1) 1 = Fault interrupt is pending 0 = No Fault interrupt is pending. This bit is cleared by setting FLTIEN = 0. bit 14 CLSTAT: Current-Limit Interrupt Status bit(1) 1 = Current-limit interrupt is pending 0 = No current-limit interrupt is pending. This bit is cleared by setting CLIEN = 0. bit 13 TRGSTAT: Trigger Interrupt Status bit 1 = Trigger interrupt is pending 0 = No trigger interrupt is pending. This bit is cleared by setting TRGIEN = 0. bit 12 FLTIEN: Fault Interrupt Enable bit 1 = Fault interrupt is enabled 0 = Fault interrupt is disabled and the FLTSTAT bit is cleared bit 11 CLIEN: Current-Limit Interrupt Enable bit 1 = Current-limit interrupt enabled 0 = Current-limit interrupt disabled and the CLSTAT bit is cleared bit 10 TRGIEN: Trigger Interrupt Enable bit 1 = A trigger event generates an interrupt request 0 = Trigger event interrupts are disabled and the TRGSTAT bit is cleared bit 9 ITB: Independent Time Base Mode bit(3) 1 = PHASEx/SPHASEx register provides time base period for this PWM generator 0 = PTPER register provides timing for this PWM generator bit 8 MDCS: Master Duty Cycle Register Select bit(3) 1 = MDC register provides duty cycle information for this PWM generator 0 = PDCx/SDCx register provides duty cycle information for this PWM generator bit 7-6 DTC<1:0>: Dead-Time Control bits 11 = Reserved 10 = Dead-time function is disabled 01 = Negative dead time actively applied for all output modes 00 = Positive dead time actively applied for all output modes bit 5-3 Unimplemented: Read as `0' Note 1: 2: 3: 4: Software must clear the interrupt status here and the corresponding IFS bit in the interrupt controller. The Independent Time Base mode (ITB = 1) must be enabled to use Center-Aligned mode. If ITB = 0, the CAM bit is ignored. These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. To operate in External Period Reset mode, configure FCLCONx = 0 and PWMCONx = 1. DS70318F-page 202 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-6: PWMCONx: PWMx CONTROL REGISTER (CONTINUED) bit 2 CAM: Center-Aligned Mode Enable bit(2,3) 1 = Center-Aligned mode is enabled 0 = Center-Aligned mode is disabled bit 1 XPRES: External PWM Reset Control bit(4) 1 = Current-limit source resets time base for this PWM generator if it is in Independent Time Base mode 0 = External pins do not affect PWM time base bit 0 IUE: Immediate Update Enable bit 1 = Updates to the active MDC/PDCx/SDCx registers are immediate 0 = Updates to the active MDC/PDCx/SDCx registers are synchronized to the PWM time base Note 1: 2: 3: 4: Software must clear the interrupt status here and the corresponding IFS bit in the interrupt controller. The Independent Time Base mode (ITB = 1) must be enabled to use Center-Aligned mode. If ITB = 0, the CAM bit is ignored. These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. To operate in External Period Reset mode, configure FCLCONx = 0 and PWMCONx = 1. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 203 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-7: R/W-0 PDCx: PWMx GENERATOR DUTY CYCLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PDCx<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PDCx<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-0 x = Bit is unknown PDCx<15:0>: PWM Generator # Duty Cycle Value bits Note 1: In Independent PWM mode, the PDCx register controls the PWMxH duty cycle only. In Complementary, Redundant and Push-Pull PWM modes, the PDCx register controls the duty cycle of both the PWMxH and PWMxL. The smallest pulse width that can be generated on the PWM output corresponds to a value of 0x0009, while the maximum pulse width generated corresponds to a value of Period-0x0008. 2: As the duty cycle gets closer to 0% or 100% of the PWM period (0 ns-40 ns, depending on the mode of operation), the PWM duty cycle resolution will degrade from 1 LSB to 3 LSB. REGISTER 15-8: R/W-0 SDCx: PWMx SECONDARY DUTY CYCLE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SDCx<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SDCx<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-0 x = Bit is unknown SDCx<15:0>: Secondary Duty Cycle for PWMxL Output Pin bits Note 1: The SDCx register is used in Independent PWM mode only. When used in Independent PWM mode, the SDCx register controls the PWMxL duty cycle. The smallest pulse width that can be generated on the PWM output corresponds to a value of 0x0009, while the maximum pulse width generated corresponds to a value of Period-0x0008. 2: As the duty cycle gets closer to 0% or 100% of the PWM period (0 ns-40 ns, depending on the mode of operation), the PWM duty cycle resolution will degrade from 1 LSB to 3 LSB. DS70318F-page 204 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-9: R/W-0 PHASEx: PWMx PRIMARY PHASE SHIFT REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PHASEx<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PHASEx<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-0 x = Bit is unknown PHASEx<15:0>: PWM Phase Shift Value or Independent Time Base Period for this PWM Generator bits Note 1: If PWMCONx = 0, the following applies based on the mode of operation: * Complementary, Redundant and Push-Pull Output mode (IOCONx = 00, 01, or 10) PHASEx<15:0> = Phase shift value for PWMxH and PWMxL outputs * True Independent Output mode (IOCONx = 11) PHASEx<15:0> = Phase shift value for PWMxL only 2: If PWMCONx = 1, the following applies based on the mode of operation: * Complementary, Redundant, and Push-Pull Output mode (IOCONx = 00, 01, or 10) PHASEx<15:0> = Independent time base period value for PWMxH and PWMxL * True Independent Output mode (IOCONx = 11) PHASEx<15:0> = Independent time base period value for PWMxL only * The smallest pulse width that can be generated on the PWM output corresponds to a value of 0x0008, while the maximum pulse width generated corresponds to a value of Period - 0x0008. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 205 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-10: SPHASEx: PWMx SECONDARY PHASE SHIFT REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SPHASEx<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SPHASEx<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 15-0 x = Bit is unknown SPHASEx<15:0>: Secondary Phase Offset for PWMxL Output Pin bits (used in Independent PWM mode only) Note 1: If PWMCONx = 0, the following applies based on the mode of operation: * Complementary, Redundant and Push-Pull Output mode (IOCONx = 00, 01, or 10) SPHASEx<15:0> = Not used * True Independent Output mode (IOCONx = 11) PHASEx<15:0> = Phase shift value for PWMxL only 2: If PWMCONx = 1, the following applies based on the mode of operation: * Complementary, Redundant and Push-Pull Output mode (IOCONx = 00, 01, or 10) SPHASEx<15:0> = Not used * True Independent Output mode (IOCONx = 11) PHASEx<15:0> = Independent time base period value for PWMxL only DS70318F-page 206 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 . REGISTER 15-11: DTRx: PWMx DEAD-TIME REGISTER U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTRx<13:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTRx<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-0 DTRx<13:0>: Unsigned 14-bit Dead-Time Value for PWMx Dead-Time Unit bits REGISTER 15-12: ALTDTRx: PWMx ALTERNATE DEAD-TIME REGISTER U-0 U-0 -- -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ALTDTRx<13:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ALTDTR <7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as `0' bit 13-0 ALTDTRx<13:0>: Unsigned 14-bit Dead-Time Value for PWMx Dead-Time Unit bits (c) 2008-2012 Microchip Technology Inc. DS70318F-page 207 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-13: TRGCONx: PWMx TRIGGER CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 TRGDIV<3:0> U-0 U-0 U-0 U-0 -- -- -- -- bit 15 bit 8 R/W-0 U-0 DTM(1) -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSTRT<5:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-12 TRGDIV<3:0>: Trigger # Output Divider bits 1111 = Trigger output for every 16th trigger event 1110 = Trigger output for every 15th trigger event 1101 = Trigger output for every 14th trigger event 1100 = Trigger output for every 13th trigger event 1011 = Trigger output for every 12th trigger event 1010 = Trigger output for every 11th trigger event 1001 = Trigger output for every 10th trigger event 1000 = Trigger output for every 9th trigger event 0111 = Trigger output for every 8th trigger event 0110 = Trigger output for every 7th trigger event 0101 = Trigger output for every 6th trigger event 0100 = Trigger output for every 5th trigger event 0011 = Trigger output for every 4th trigger event 0010 = Trigger output for every 3rd trigger event 0001 = Trigger output for every 2nd trigger event 0000 = Trigger output for every trigger event bit 11-8 Unimplemented: Read as `0' bit 7 DTM: Dual Trigger Mode bit(1) 1 = Secondary trigger event is combined with the primary trigger event to create the PWM trigger. 0 = Secondary trigger event is not combined with the primary trigger event to create the PWM trigger. Two separate PWM triggers are generated. bit 6 Unimplemented: Read as `0' bit 5-0 TRGSTRT<5:0>: Trigger Postscaler Start Enable Select bits 111111 = Wait 63 PWM cycles before generating the first trigger event after the module is enabled * * * 000010 = Wait 1 PWM cycles before generating the first trigger event after the module is enabled 000001 = Wait 1 PWM cycles before generating the first trigger event after the module is enabled 000000 = Wait 0 PWM cycles before generating the first trigger event after the module is enabled Note 1: The secondary generator cannot generate PWM trigger interrupts. DS70318F-page 208 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-14: IOCONx: PWMx I/O CONTROL REGISTER R/W-0 R/W-0 PENH PENL R/W-0 POLH R/W-0 POLL R/W-0 R/W-0 PMOD<1:0>(1) R/W-0 R/W-0 OVRENH OVRENL bit 15 bit 8 R/W-0 R/W-0 R/W-0 OVRDAT<1:0> R/W-0 FLTDAT<1:0> R/W-0 R/W-0 CLDAT<1:0> R/W-0 R/W-0 SWAP OSYNC bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 PENH: PWMH Output Pin Ownership bit 1 = PWM module controls PWMxH pin 0 = GPIO module controls PWMxH pin bit 14 PENL: PWML Output Pin Ownership bit 1 = PWM module controls PWMxL pin 0 = GPIO module controls PWMxL pin bit 13 POLH: PWMH Output Pin Polarity bit 1 = PWMxH pin is active-low 0 = PWMxH pin is active-high bit 12 POLL: PWML Output Pin Polarity bit 1 = PWMxL pin is active-low 0 = PWMxL pin is active-high bit 11-10 PMOD<1:0>: PWM # I/O Pin Mode bits(1) 11 = PWM I/O pin pair is in the True Independent Output mode 10 = PWM I/O pin pair is in the Push-Pull Output mode 01 = PWM I/O pin pair is in the Redundant Output mode 00 = PWM I/O pin pair is in the Complementary Output mode bit 9 OVRENH: Override Enable for PWMxH Pin bit 1 = OVRDAT<1> provides data for output on PWMxH pin 0 = PWM generator provides data for PWMxH pin bit 8 OVRENL: Override Enable for PWMxL Pin bit 1 = OVRDAT<0> provides data for output on PWMxL pin 0 = PWM generator provides data for PWMxL pin bit 7-6 OVRDAT<1:0>: Data for PWMxH and PWMxL Pins if Override is Enabled bits If OVERENH = 1 then OVRDAT<1> provides data for PWMxH. If OVERENL = 1 then OVRDAT<0> provides data for PWMxL. bit 5-4 FLTDAT<1:0>: State(2) for PWMxH and PWMxL Pins if FLTMOD is Enabled bits FCLCONx = 0: Normal Fault mode: If Fault active, then FLTDAT<1> provides state for PWMxH. If Fault active, then FLTDAT<0> provides state for PWMxL. FCLCONx = 1: Independent Fault mode: If current-limit active, then FLTDAT<1> provides data for PWMxH. If Fault active, then FLTDAT<0> provides state for PWMxL. Note 1: 2: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. State represents the active/inactive state of the PWM module depending on the POLH and POLL bit settings. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 209 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-14: IOCONx: PWMx I/O CONTROL REGISTER (CONTINUED) bit 3-2 CLDAT<1:0>: State(2) for PWMxH and PWMxL Pins if CLMODE is Enabled bits FCLCONx = 0: Normal Fault mode: If current-limit active, then CLDAT<1> provides state for PWMxH. If current-limit active, then CLDAT<0> provides state for PWMxL. FCLCONx = 1: Independent Fault mode: CLDAT<1:0> is ignored. bit 1 SWAP<1:0>: SWAP PWMxH and PWMxL pins 1 = PWMxH output signal is connected to PWMxL pin and PWMxL signal is connected to PWMxH pins 0 = PWMxH and PWMxL pins are mapped to their respective pins bit 0 OSYNC: Output Override Synchronization bit 1 = Output overrides via the OVRDAT<1:0> bits are synchronized to the PWM time base 0 = Output overrides via the OVDDAT<1:0> bits occur on next CPU clock boundary Note 1: 2: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. State represents the active/inactive state of the PWM module depending on the POLH and POLL bit settings. DS70318F-page 210 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-15: FCLCONx: PWMx FAULT CURRENT-LIMIT CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CLSRC<4:0>(2,3) IFLTMOD R/W-0 R/W-0 CLPOL(1) CLMOD bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 FLTSRC<4:0>(2,3) R/W-0 R/W-0 (1) FLTPOL R/W-0 FLTMOD<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 IFLTMOD: Independent Fault Mode Enable bit 1 = Independent Fault mode: Current-limit input maps FLTDAT<1> to PWMxH output and Fault input maps FLTDAT<0> to PWMxL output. The CLDAT<1:0> bits are not used for override functions. 0 = Normal Fault mode: Current-limit feature maps CLDAT<1:0> bits to the PWMxH and PWMxL outputs. The PWM Fault feature maps FLTDAT<1:0> to the PWMxH and PWMxL outputs. bit 14-10 CLSRC<4:0>: Current-Limit Control Signal Source Select for PWM # Generator bits(2,3) 11111 = Reserved * * * 01000 = Reserved 00111 = Fault 8 00110 = Fault 7 00101 = Fault 6 00100 = Fault 5 00011 = Fault 4 00010 = Fault 3 00001 = Fault 2 00000 = Fault 1 bit 9 CLPOL: Current-Limit Polarity for PWM Generator # bit(1) 1 = The selected current-limit source is active-low 0 = The selected current-limit source is active-high bit 8 CLMOD: Current-Limit Mode Enable bit for PWM Generator # bit 1 = Current-limit function is enabled 0 = Current-limit function is disabled Note 1: 2: 3: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. When Independent Fault mode is enabled (IFLTMOD = 1), and Fault 1 is used for Current-Limit mode (CLSRC<4:0> = b0000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused Fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs. When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode (FLTSRC<4:0> = b0000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an unused current-limit source to prevent the current-limit source from disabling both the PWMxH and PWMxL outputs. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 211 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-15: FCLCONx: PWMx FAULT CURRENT-LIMIT CONTROL REGISTER (CONTINUED) bit 7-3 FLTSRC<4:0>: Fault Control Signal Source Select for PWM Generator # bits(2,3) 11111 = Reserved * * * 01000 = Reserved 00111 = Fault 8 00110 = Fault 7 00101 = Fault 6 00100 = Fault 5 00011 = Fault 4 00010 = Fault 3 00001 = Fault 2 00000 = Fault 1 bit 2 FLTPOL: Fault Polarity for PWM Generator # bit(1) 1 = The selected Fault source is active-low 0 = The selected Fault source is active-high bit 1-0 FLTMOD<1:0>: Fault Mode for PWM Generator # bits 11 = Fault input is disabled 10 = Reserved 01 = The selected Fault source forces PWMxH, PWMxL pins to FLTDAT values (cycle) 00 = The selected Fault source forces PWMxH, PWMxL pins to FLTDAT values (latched condition) Note 1: 2: 3: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will yield unpredictable results. When Independent Fault mode is enabled (IFLTMOD = 1), and Fault 1 is used for Current-Limit mode (CLSRC<4:0> = b0000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused Fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs. When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode (FLTSRC<4:0> = b0000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an unused current-limit source to prevent the current-limit source from disabling both the PWMxH and PWMxL outputs. DS70318F-page 212 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-16: TRIGx: PWMx PRIMARY TRIGGER COMPARE VALUE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGCMP<12:5> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGCMP<4:0> U-0 U-0 U-0 -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-3 TRGCMP<12:0>: Trigger Control Value bits When primary PWM functions in local time base, this register contains the compare values that can trigger the ADC module. bit 2-0 Unimplemented: Read as `0' REGISTER 15-17: STRIGx: PWMx SECONDARY TRIGGER COMPARE VALUE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STRGCMP<12:5> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STRGCMP<4:0> U-0 U-0 U-0 -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-3 STRGCMP<12:0>: Secondary Trigger Control Value bits When secondary PWM functions in local time base, this register contains the compare values that can trigger the ADC module. bit 2-0 Unimplemented: Read as `0' (c) 2008-2012 Microchip Technology Inc. DS70318F-page 213 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-18: LEBCONx: LEADING-EDGE BLANKING CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PHR PHF PLR PLF FLTLEBEN CLLEBEN R/W-0 R/W-0 LEB<6:5> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LEB<4:0> U-0 U-0 U-0 -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 PHR: PWMxH Rising Edge Trigger Enable bit 1 = Rising edge of PWMxH will trigger LEB counter 0 = LEB ignores rising edge of PWMxH bit 14 PHF: PWMH Falling Edge Trigger Enable bit 1 = Falling edge of PWMxH will trigger LEB counter 0 = LEB ignores falling edge of PWMxH bit 13 PLR: PWML Rising Edge Trigger Enable bit 1 = Rising edge of PWMxL will trigger LEB counter 0 = LEB ignores rising edge of PWMxL bit 12 PLF: PWML Falling Edge Trigger Enable bit 1 = Falling edge of PWMxL will trigger LEB counter 0 = LEB ignores falling edge of PWMxL bit 11 FLTLEBEN: Fault Input LEB Enable bit 1 = Leading-edge blanking is applied to selected Fault input 0 = Leading-edge blanking is not applied to selected Fault input bit 10 CLLEBEN: Current-Limit LEB Enable bit 1 = Leading-edge blanking is applied to selected current-limit input 0 = Leading-edge blanking is not applied to selected current-limit input bit 9-3 LEB<6:0>: Leading-Edge Blanking for Current-Limit and Fault Inputs bits Value is 8.32 nsec increments. bit 2-0 Unimplemented: Read as `0' DS70318F-page 214 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 15-19: PWMCAPx: PRIMARY PWMx TIME BASE CAPTURE REGISTER R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 PWMCAP<12:5>(1,2) bit 15 bit 8 R-0 R-0 R-0 R-0 R-0 PWMCAP<4:0>(1,2) U-0 U-0 U-0 -- -- -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-3 PWMCAP<12:0>: Captured PWM Time Base Value bits(1,2) The value in this register represents the captured PWM time base value when a leading edge is detected on the current-limit input. bit 2-0 Unimplemented: Read as `0' Note 1: 2: The capture feature is only available on primary output (PWMxH). This feature is active only after LEB processing on the current-limit input signal is complete. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 215 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 216 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 16.0 SERIAL PERIPHERAL INTERFACE (SPI) Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 18. "Serial Peripheral Interface (SPI)" (DS70206) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. FIGURE 16-1: The Serial Peripheral Interface (SPI) module is a synchronous serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices can be serial EEPROMs, shift registers, display drivers, analog-to-digital converters and so on. The SPI module is compatible with SPI and SIOP from Motorola(R). The SPI module consists of a 16-bit shift register, SPIxSR (where x = 1), used for shifting data in and out, and a buffer register, SPIxBUF. A control register, SPIxCON, configures the module. Additionally, a status register, SPIxSTAT, indicates status conditions. The serial interface consists of the following four pins: * * * * SDIx (Serial Data Input) SDOx (Serial Data Output) SCKx (Shift Clock Input Or Output) SSx (Active-Low Slave Select). In Master mode operation, SCK is a clock output; in Slave mode, it is a clock input. SPI MODULE BLOCK DIAGRAM SCKx 1:1 to 1:8 Secondary Prescaler 1:1/4/16/64 Primary Prescaler FCY SSx Sync Control Select Edge Control Clock SPIxCON1<1:0> Shift Control SPIxCON1<4:2> SDOx Enable Master Clock bit 0 SDIx SPIxSR Transfer Transfer SPIxRXB SPIxTXB SPIxBUF Read SPIxBUF Write SPIxBUF 16 Internal Data Bus (c) 2008-2012 Microchip Technology Inc. DS70318F-page 217 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 16-1: SPIxSTAT: SPIx STATUS AND CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 SPIEN -- SPISIDL -- -- -- -- -- bit 15 bit 8 U-0 R/C-0 U-0 U-0 U-0 U-0 R-0 R-0 -- SPIROV -- -- -- -- SPITBF SPIRBF bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 SPIEN: SPIx Enable bit 1 = Enables module and configures SCKx, SDOx, SDIx and SSx as serial port pins 0 = Disables module bit 14 Unimplemented: Read as `0' bit 13 SPISIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12-7 Unimplemented: Read as `0' bit 6 SPIROV: Receive Overflow Flag bit 1 = A new byte/word is completely received and discarded. The user software has not read the previous data in the SPIxBUF register. 0 = No overflow has occurred bit 5-2 Unimplemented: Read as `0' bit 1 SPITBF: SPIx Transmit Buffer Full Status bit 1 = Transmit not yet started, SPIxTXB is full 0 = Transmit started, SPIxTXB is empty. Automatically set in hardware when CPU writes SPIxBUF location, loading SPIxTXB. Automatically cleared in hardware when SPIx module transfers data from SPIxTXB to SPIxSR. bit 0 SPIRBF: SPIx Receive Buffer Full Status bit 1 = Receive complete, SPIxRXB is full 0 = Receive is not complete, SPIxRXB is empty. Automatically set in hardware when SPIx transfers data from SPIxSR to SPIxRXB. Automatically cleared in hardware when core reads SPIxBUF location, reading SPIxRXB. DS70318F-page 218 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 16-2: SPIXCON1: SPIx CONTROL REGISTER 1 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- DISSCK DISSDO MODE16 SMP CKE(1) bit 15 bit 8 R/W-0 R/W-0 SSEN(3) CKP R/W-0 R/W-0 MSTEN R/W-0 R/W-0 R/W-0 (2) R/W-0 PPRE<1:0>(2) SPRE<2:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as `0' bit 12 DISSCK: Disable SCKx pin bit (SPI Master modes only) 1 = Internal SPI clock is disabled; pin functions as I/O 0 = Internal SPI clock is enabled bit 11 DISSDO: Disable SDOx pin bit 1 = SDOx pin is not used by module; pin functions as I/O 0 = SDOx pin is controlled by the module bit 10 MODE16: Word/Byte Communication Select bit 1 = Communication is word-wide (16 bits) 0 = Communication is byte-wide (8 bits) bit 9 SMP: SPIx Data Input Sample Phase bit Master mode: 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time Slave mode: SMP must be cleared when SPIx is used in Slave mode. bit 8 CKE: SPIx Clock Edge Select bit(1) 1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6) 0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6) bit 7 SSEN: Slave Select Enable bit (Slave mode)(3) 1 = SSx pin used for Slave mode 0 = SSx pin not used by module; pin controlled by port function bit 6 CKP: Clock Polarity Select bit 1 = Idle state for clock is a high level; active state is a low level 0 = Idle state for clock is a low level; active state is a high level bit 5 MSTEN: Master Mode Enable bit 1 = Master mode 0 = Slave mode Note 1: 2: 3: The CKE bit is not used in the Framed SPI modes. Program this bit to `0' for the Framed SPI modes (FRMEN = 1). Do not set both primary and secondary prescalers to a value of 1:1. This bit must be cleared when FRMEN = 1. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 219 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 16-2: SPIXCON1: SPIx CONTROL REGISTER 1 (CONTINUED) bit 4-2 SPRE<2:0>: Secondary Prescale bits (Master mode)(2) 111 = Secondary prescale 1:1 110 = Secondary prescale 2:1 * * * 000 = Secondary prescale 8:1 bit 1-0 PPRE<1:0>: Primary Prescale bits (Master mode)(2) 11 = Primary prescale 1:1 10 = Primary prescale 4:1 01 = Primary prescale 16:1 00 = Primary prescale 64:1 Note 1: 2: 3: The CKE bit is not used in the Framed SPI modes. Program this bit to `0' for the Framed SPI modes (FRMEN = 1). Do not set both primary and secondary prescalers to a value of 1:1. This bit must be cleared when FRMEN = 1. DS70318F-page 220 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 16-3: SPIxCON2: SPIx CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 FRMEN SPIFSD FRMPOL -- -- -- -- -- bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 U-0 -- -- -- -- -- -- FRMDLY -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 FRMEN: Framed SPIx Support bit 1 = Framed SPIx support enabled (SSx pin used as frame sync pulse input/output) 0 = Framed SPIx support disabled bit 14 SPIFSD: Frame Sync Pulse Direction Control bit 1 = Frame sync pulse input (slave) 0 = Frame sync pulse output (master) bit 13 FRMPOL: Frame Sync Pulse Polarity bit 1 = Frame sync pulse is active-high 0 = Frame sync pulse is active-low bit 12-2 Unimplemented: Read as `0' bit 1 FRMDLY: Frame Sync Pulse Edge Select bit 1 = Frame sync pulse coincides with first bit clock 0 = Frame sync pulse precedes first bit clock bit 0 Unimplemented: This bit must not be set to `1' by the user application (c) 2008-2012 Microchip Technology Inc. DS70318F-page 221 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 222 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 17.0 INTER-INTEGRATED CIRCUIT (I2CTM) Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 19. "Inter-Integrated Circuit (I2CTM)" (DS70195) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. (I2C) The Inter-Integrated Circuit module provides complete hardware support for both Slave and Multi-Master modes of the I2C serial communication standard with a 16-bit interface. The I2C module has a 2-pin interface, where: * The SCLx pin is clock * The SDAx pin is data The I2C module offers the following key features: * I2C interface supporting both Master and Slave modes of operation * I2C Slave mode supports 7-bit and 10-bit addressing * I2C Master mode supports 7-bit and 10-bit addressing * I2C port allows bidirectional transfers between master and slaves * Serial clock synchronization for I2C port can be used as a handshake mechanism to suspend and resume serial transfer (SCLREL control) * I2C supports multi-master operation, detects bus collision and arbitrates accordingly 17.1 Operating Modes The hardware fully implements all the master and slave functions of the I2C Standard and Fast mode specifications, as well as 7-bit and 10-bit addressing. The I2C module can operate either as a slave or a master on an I2C bus. The following types of I2C operation are supported: * * * (c) 2008-2012 Microchip Technology Inc. I2C slave operation with 7-bit addressing I2C slave operation with 10-bit addressing I2C master operation with 7-bit or 10-bit addressing DS70318F-page 223 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 17-1: I2CTM BLOCK DIAGRAM (X = 1) Internal Data Bus I2CxRCV Read SCLx Shift Clock I2CxRSR LSb SDAx Address Match Match Detect Write I2CxMSK Write Read I2CxADD Read Start and Stop Bit Detect Write Start and Stop Bit Generation Control Logic I2CxSTAT Collision Detect Read Write I2CxCON Acknowledge Generation Read Clock Stretching Write I2CxTRN LSb Read Shift Clock Reload Control BRG Down Counter Write I2CxBRG Read TCY/2 DS70318F-page 224 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 17.2 I2C Registers I2CxCON and I2CxSTAT are control and status registers. The I2CxCON register is readable and writable. The lower six bits of I2CxSTAT are read-only. The remaining bits of the I2CxSTAT are read/write: * I2CxRSR is the shift register used for shifting data internal to the module and the user application has no access to it * I2CxRCV is the receive buffer and the register to which data bytes are written, or from which data bytes are read * I2CxTRN is the transmit register to which bytes are written during a transmit operation * The I2CxADD register holds the slave address * A status bit, ADD10, indicates 10-bit Address mode * The I2CxBRG acts as the Baud Rate Generator (BRG) reload value In receive operations, I2CxRSR and I2CxRCV together form a double-buffered receiver. When I2CxRSR receives a complete byte, it is transferred to I2CxRCV, and an interrupt pulse is generated. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 225 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 17-1: I2CxCON: I2Cx CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-1, HC R/W-0 R/W-0 R/W-0 R/W-0 I2CEN -- I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN bit 7 bit 0 Legend: U = Unimplemented bit, read as `0' R = Readable bit W = Writable bit HS = Hardware Settable bit HC = Hardware Clearable bit -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 I2CEN: I2Cx Enable bit 1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins 0 = Disables the I2Cx module. All I2C pins are controlled by port functions. bit 14 Unimplemented: Read as `0' bit 13 I2CSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters an Idle mode 0 = Continue module operation in Idle mode bit 12 SCLREL: SCLx Release Control bit (when operating as I2C slave) 1 = Release SCLx clock 0 = Hold SCLx clock low (clock stretch) If STREN = 1: Bit is R/W (i.e., software can write `0' to initiate stretch and write `1' to release clock). Hardware clear at beginning of slave transmission. Hardware clear at end of slave reception. If STREN = 0: Bit is R/S (i.e., software can only write `1' to release clock). Hardware clear at beginning of slave transmission. bit 11 IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit 1 = IPMI mode is enabled; all addresses acknowledged 0 = IPMI mode disabled bit 10 A10M: 10-bit Slave Address bit 1 = I2CxADD is a 10-bit slave address 0 = I2CxADD is a 7-bit slave address bit 9 DISSLW: Disable Slew Rate Control bit 1 = Slew rate control disabled 0 = Slew rate control enabled bit 8 SMEN: SMbus Input Levels bit 1 = Enable I/O pin thresholds compliant with SMbus specification 0 = Disable SMbus input thresholds bit 7 GCEN: General Call Enable bit (when operating as I2C slave) 1 = Enable interrupt when a general call address is received in the I2CxRSR (module is enabled for reception) 0 = General call address disabled bit 6 STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave) Used in conjunction with SCLREL bit. 1 = Enable software or receive clock stretching 0 = Disable software or receive clock stretching DS70318F-page 226 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 17-1: I2CxCON: I2Cx CONTROL REGISTER (CONTINUED) bit 5 ACKDT: Acknowledge Data bit (when operating as I2C master, applicable during master receive) Value that is transmitted when the software initiates an Acknowledge sequence. 1 = Send NACK during Acknowledge 0 = Send ACK during Acknowledge bit 4 ACKEN: Acknowledge Sequence Enable bit (when operating as I2C master, applicable during master receive) 1 = Initiate Acknowledge sequence on SDAx and SCLx pins and transmit ACKDT data bit. Hardware clear at end of master Acknowledge sequence. 0 = Acknowledge sequence not in progress bit 3 RCEN: Receive Enable bit (when operating as I2C master) 1 = Enables Receive mode for I2C. Hardware clear at end of eighth bit of master receive data byte. 0 = Receive sequence not in progress bit 2 PEN: Stop Condition Enable bit (when operating as I2C master) 1 = Initiate Stop condition on SDAx and SCLx pins. Hardware clear at end of master Stop sequence. 0 = Stop condition not in progress bit 1 RSEN: Repeated Start Condition Enable bit (when operating as I2C master) 1 = Initiate Repeated Start condition on SDAx and SCLx pins. Hardware clear at end of master Repeated Start sequence. 0 = Repeated Start condition not in progress bit 0 SEN: Start Condition Enable bit (when operating as I2C master) 1 = Initiate Start condition on SDAx and SCLx pins. Hardware clear at end of master Start sequence. 0 = Start condition not in progress (c) 2008-2012 Microchip Technology Inc. DS70318F-page 227 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 17-2: I2CxSTAT: I2Cx STATUS REGISTER R-0, HSC R-0, HSC U-0 U-0 U-0 R/C-0, HSC R-0, HSC R-0, HSC ACKSTAT TRSTAT -- -- -- BCL GCSTAT ADD10 bit 15 bit 8 R/C-0, HS R/C-0, HS R-0, HSC IWCOL I2COV D_A R/C-0, HSC R/C-0, HSC P R-0, HSC R-0, HSC R-0, HSC R_W RBF TBF S bit 7 bit 0 Legend: U = Unimplemented bit, read as `0' R = Readable bit W = Writable bit HS = Hardware Settable bit HSC = Hardware Settable/Clearable -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 ACKSTAT: Acknowledge Status bit (when operating as I2C master, applicable to master transmit operation) 1 = NACK received from slave 0 = ACK received from slave Hardware set or clear at end of slave Acknowledge. bit 14 TRSTAT: Transmit Status bit (when operating as I2C master, applicable to master transmit operation) 1 = Master transmit is in progress (8 bits + ACK) 0 = Master transmit is not in progress Hardware set at beginning of master transmission. Hardware clear at end of slave Acknowledge. bit 13-11 Unimplemented: Read as `0' bit 10 BCL: Master Bus Collision Detect bit 1 = A bus collision has been detected during a master operation 0 = No collision Hardware set at detection of bus collision. bit 9 GCSTAT: General Call Status bit 1 = General call address was received 0 = General call address was not received Hardware set when address matches general call address. Hardware clear at Stop detection. bit 8 ADD10: 10-bit Address Status bit 1 = 10-bit address was matched 0 = 10-bit address was not matched Hardware set at match of 2nd byte of matched 10-bit address. Hardware clear at Stop detection. bit 7 IWCOL: Write Collision Detect bit 1 = An attempt to write the I2CxTRN register failed because the I2C module is busy 0 = No collision Hardware set at occurrence of write to I2CxTRN while busy (cleared by software). bit 6 I2COV: Receive Overflow Flag bit 1 = A byte was received while the I2CxRCV register is still holding the previous byte 0 = No overflow Hardware set at attempt to transfer I2CxRSR to I2CxRCV (cleared by software). bit 5 D_A: Data/Address bit (when operating as I2C slave) 1 = Indicates that the last byte received was data 0 = Indicates that the last byte received was device address Hardware clear at device address match. Hardware set by reception of slave byte. bit 4 P: Stop bit 1 = Indicates that a Stop bit has been detected last 0 = Stop bit was not detected last Hardware set or clear when Start, Repeated Start or Stop detected. DS70318F-page 228 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 17-2: I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED) bit 3 S: Start bit 1 = Indicates that a Start (or Repeated Start) bit has been detected last 0 = Start bit was not detected last Hardware set or clear when Start, Repeated Start or Stop detected. bit 2 R_W: Read/Write Information bit (when operating as I2C slave) 1 = Read - indicates data transfer is output from slave 0 = Write - indicates data transfer is input to slave Hardware set or clear after reception of I 2C device address byte. bit 1 RBF: Receive Buffer Full Status bit 1 = Receive complete, I2CxRCV is full 0 = Receive not complete, I2CxRCV is empty Hardware set when I2CxRCV is written with received byte. Hardware clear when software reads I2CxRCV. bit 0 TBF: Transmit Buffer Full Status bit 1 = Transmit in progress, I2CxTRN is full 0 = Transmit complete, I2CxTRN is empty Hardware set when software writes I2CxTRN. Hardware clear at completion of data transmission. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 229 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 17-3: I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- R/W-0 R/W-0 AMSK<9:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 AMSK<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as `0' bit 9-0 AMSK<9:0>: Mask for Address bit x Select bits 1 = Enable masking for bit x of incoming message address; bit match not required in this position 0 = Disable masking for bit x; bit match required in this position DS70318F-page 230 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 18.0 UNIVERSAL ASYNCHRONOUS RECEIVER TRANSMITTER (UART) Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 family of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 17. "UART" (DS70188) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The Universal Asynchronous Receiver Transmitter (UART) module is one of the serial I/O modules available in the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 device families. The UART is a full-duplex, asynchronous system that can communicate with peripheral devices, such as personal computers, LIN, RS-232 and RS-485 interfaces. The module also supports a hardware flow control option with the UxCTS and UxRTS pins and also includes an IrDA(R) encoder and decoder. FIGURE 1: The primary features of the UART module are: * Full-Duplex, 8-bit or 9-bit Data Transmission through the UxTX and UxRX pins * Even, Odd or No Parity Options (for 8-bit data) * One or Two Stop bits * Hardware Flow Control Option with UxCTS and UxRTS Pins * Fully Integrated Baud Rate Generator with 16-bit Prescaler * Baud Rates Ranging from 12.5 Mbps to 38 bps at 50 MIPS * 4-Deep First-In First-Out (FIFO) Transmit Data Buffer * 4-Deep FIFO Receive Data Buffer * Parity, Framing and Buffer Overrun Error Detection * Support for 9-bit mode with Address Detect (9th bit = 1) * Transmit and Receive Interrupts * A Separate Interrupt for all UART Error Conditions * Loopback mode for Diagnostic Support * Support for Sync and Break Characters * Support for Automatic Baud Rate Detection * IrDA Encoder and Decoder Logic * 16x Baud Clock Output for IrDA(R) Support A simplified block diagram of the UART module is shown in Figure 1. The UART module consists of these key hardware elements: * Baud Rate Generator * Asynchronous Transmitter * Asynchronous Receiver UART SIMPLIFIED BLOCK DIAGRAM Baud Rate Generator IrDA(R) Hardware Flow Control U1RTS/BCLK1 U1CTS UART Receiver U1RX UART Transmitter U1TX (c) 2008-2012 Microchip Technology Inc. DS70318F-page 231 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 18-1: R/W-0 UxMODE: UARTx MODE REGISTER U-0 UARTEN(1) -- R/W-0 USIDL R/W-0 IREN (2) R/W-0 U-0 RTSMD -- R/W-0 R/W-0 UEN<1:0> bit 15 bit 8 R/W-0 HC R/W-0 R/W-0, HC R/W-0 R/W-0 WAKE LPBACK ABAUD URXINV BRGH R/W-0 R/W-0 PDSEL<1:0> R/W-0 STSEL bit 7 bit 0 Legend: HC = Hardware Clearable R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 UARTEN: UARTx Enable bit(1) 1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0> 0 = UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption minimal bit 14 Unimplemented: Read as `0' bit 13 USIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12 IREN: IrDA(R) Encoder and Decoder Enable bit(2) 1 = IrDA(R) encoder and decoder enabled 0 = IrDA(R) encoder and decoder disabled bit 11 RTSMD: Mode Selection for UxRTS Pin bit 1 = UxRTS pin in Simplex mode 0 = UxRTS pin in Flow Control mode bit 10 Unimplemented: Read as `0' bit 9-8 UEN<1:0>: UARTx Enable bits 11 = UxTX, UxRX and BCLK pins are enabled and used; UxCTS pin controlled by port latches 10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used 01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin controlled by port latches 00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLK pins controlled by port latches bit 7 WAKE: Wake-up on Start bit Detect During Sleep Mode Enable bit 1 = UARTx will continue to sample the UxRX pin; interrupt generated on falling edge; bit cleared in hardware on following rising edge 0 = No wake-up enabled bit 6 LPBACK: UARTx Loopback Mode Select bit 1 = Enable Loopback mode 0 = Loopback mode is disabled bit 5 ABAUD: Auto-Baud Enable bit 1 = Enable baud rate measurement on the next character - requires reception of a Sync field (55h) before other data; cleared in hardware upon completion 0 = Baud rate measurement disabled or completed bit 4 URXINV: Receive Polarity Inversion bit 1 = UxRX Idle state is `0' 0 = UxRX Idle state is `1' Note 1: 2: Refer to Section 17. "UART" (DS70188) in the "dsPIC33F/PIC24H Family Reference Manual" for information on enabling the UART module for receive or transmit operation. This feature is only available for the 16x BRG mode (BRGH = 0). DS70318F-page 232 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 18-1: UxMODE: UARTx MODE REGISTER (CONTINUED) bit 3 BRGH: High Baud Rate Enable bit 1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode) 0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode) bit 2-1 PDSEL<1:0>: Parity and Data Selection bits 11 = 9-bit data, no parity 10 = 8-bit data, odd parity 01 = 8-bit data, even parity 00 = 8-bit data, no parity bit 0 STSEL: Stop Bit Selection bit 1 = Two Stop bits 0 = One Stop bit Note 1: 2: Refer to Section 17. "UART" (DS70188) in the "dsPIC33F/PIC24H Family Reference Manual" for information on enabling the UART module for receive or transmit operation. This feature is only available for the 16x BRG mode (BRGH = 0). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 233 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 18-2: R/W-0 UxSTA: UARTx STATUS AND CONTROL REGISTER R/W-0 UTXISEL1 UTXINV R/W-0 UTXISEL0 U-0 -- R/W-0, HC UTXBRK R/W-0 (1) UTXEN R-0 R-1 UTXBF TRMT bit 15 bit 8 R/W-0 R/W-0 URXISEL<1:0> R/W-0 R-1 R-0 R-0 R/C-0 R-0 ADDEN RIDLE PERR FERR OERR URXDA bit 7 bit 0 Legend: HC = Hardware Clearable bit C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15,13 UTXISEL<1:0>: Transmission Interrupt Mode Selection bits 11 = Reserved; do not use 10 = Interrupt when a character is transferred to the Transmit Shift register, and as a result, the transmit buffer becomes empty 01 = Interrupt when the last character is shifted out of the Transmit Shift register; all transmit operations are completed 00 = Interrupt when a character is transferred to the Transmit Shift register (this implies there is at least one character open in the transmit buffer) bit 14 UTXINV: Transmit Polarity Inversion bit If IREN = 0: 1 = UxTX Idle state is `0' 0 = UxTX Idle state is `1' If IREN = 1: 1 = IrDA(R) encoded UxTX Idle state is `1' 0 = IrDA(R) encoded UxTX Idle state is `0' bit 12 Unimplemented: Read as `0' bit 11 UTXBRK: Transmit Break bit 1 = Send Sync Break on next transmission - Start bit, followed by twelve `0' bits, followed by Stop bit; cleared by hardware upon completion 0 = Sync Break transmission disabled or completed bit 10 UTXEN: Transmit Enable bit(1) 1 = Transmit enabled, UxTX pin controlled by UARTx 0 = Transmit disabled, any pending transmission is aborted and buffer is reset; UxTX pin controlled by port bit 9 UTXBF: Transmit Buffer Full Status bit (read-only) 1 = Transmit buffer is full 0 = Transmit buffer is not full; at least one more character can be written bit 8 TRMT: Transmit Shift Register Empty bit (read-only) 1 = Transmit Shift register is empty and transmit buffer is empty (the last transmission has completed) 0 = Transmit Shift register is not empty, a transmission is in progress or queued bit 7-6 URXISEL<1:0>: Receive Interrupt Mode Selection bits 11 = Interrupt is set on UxRSR transfer making the receive buffer full (i.e., has 4 data characters) 10 = Interrupt is set on UxRSR transfer making the receive buffer 3/4 full (i.e., has 3 data characters) 0x = Interrupt is set when any character is received and transferred from the UxRSR to the receive buffer; receive buffer has one or more characters Note 1: Refer to Section 17. "UART" (DS70188) in the "dsPIC33F/PIC24H Family Reference Manual" for information on enabling the UART module for transmit operation. DS70318F-page 234 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 18-2: UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED) bit 5 ADDEN: Address Character Detect bit (bit 8 of received data = 1) 1 = Address Detect mode enabled. If 9-bit mode is not selected, this does not take effect. 0 = Address Detect mode disabled bit 4 RIDLE: Receiver Idle bit (read-only) 1 = Receiver is Idle 0 = Receiver is active bit 3 PERR: Parity Error Status bit (read-only) 1 = Parity error has been detected for the current character (character at the top of the receive FIFO) 0 = Parity error has not been detected bit 2 FERR: Framing Error Status bit (read-only) 1 = Framing error has been detected for the current character (character at the top of the receive FIFO) 0 = Framing error has not been detected bit 1 OERR: Receive Buffer Overrun Error Status bit (clear/read-only) 1 = Receive buffer has overflowed 0 = Receive buffer has not overflowed. Clearing a previously set OERR bit (1 0 transition) will reset the receiver buffer and the UxRSR to the empty state. bit 0 URXDA: Receive Buffer Data Available bit (read-only) 1 = Receive buffer has data, at least one more character can be read 0 = Receive buffer is empty Note 1: Refer to Section 17. "UART" (DS70188) in the "dsPIC33F/PIC24H Family Reference Manual" for information on enabling the UART module for transmit operation. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 235 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 236 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 19.0 HIGH-SPEED 10-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 44. "High-Speed 10-bit Analog-to-Digital Converter (ADC)" (DS70321) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices provide high-speed successive approximation analog to digital conversions to support applications such as AC/DC and DC/DC power converters. 19.1 Features Overview The ADC module comprises the following features: * 10-bit resolution * Unipolar inputs * Up to two Successive Approximation Registers (SARs) * Up to 12 external input channels * Up to two internal analog inputs * Dedicated result register for each analog input * 1 LSB accuracy at 3.3V * Single supply operation * 4 Msps conversion rate at 3.3V (devices with two SARs) * 2 Msps conversion rate at 3.3V (devices with one SAR) * Low-power CMOS technology 19.2 Module Description This ADC module is designed for applications that require low latency between the request for conversion and the resultant output data. Typical applications include: * AC/DC power supplies * DC/DC converters * Power Factor Correction (PFC) (c) 2008-2012 Microchip Technology Inc. This ADC works with the high-speed PWM module in power control applications that require high-frequency control loops. This module can sample and convert two analog inputs in a 0.5 microsecond when two SARs are used. This small conversion delay reduces the "phase lag" between measurement and control system response. Up to five inputs may be sampled at a time (four inputs from the dedicated sample and hold circuits and one from the shared sample and hold circuit). If multiple inputs request conversion, the ADC will convert them in a sequential manner, starting with the lowest order input. This ADC design provides each pair of analog inputs (AN1,AN0), (AN3,AN2),..., the ability to specify its own trigger source out of a maximum of sixteen different trigger sources. This capability allows this ADC to sample and convert analog inputs that are associated with PWM generators operating on independent time bases. The user application typically requires synchronization between analog data sampling and PWM output to the application circuit. The very high-speed operation of this ADC module allows "data on demand". In addition, several hardware features have been added to the peripheral interface to improve real-time performance in a typical DSP-based application. * * * * Result alignment options Automated sampling External conversion start control Two internal inputs to monitor INTREF internal reference and EXTREF input signal 19.3 Module Functionality The high-speed 10-bit ADC module is designed to support power conversion applications when used with the High-Speed PWM module. The ADC may have one or two SAR modules, depending on the device variant. If two SARs are present on a device, two conversions can be processed at a time, yielding 4 Msps conversion rate. If only one SAR is present on a device, only one conversion can be processed at a time, yielding 2 Msps conversion rate. The high-speed 10-bit ADC produces two 10-bit conversion results in a 0.5 microsecond. The ADC module supports up to 12 external analog inputs and two internal analog inputs. To monitor reference voltage, two internal inputs, AN12 and AN13, are connected to the EXTREF and INTREF voltages, respectively. The analog reference voltage is defined as the device supply voltage (AVDD/AVSS). Block diagrams of the ADC module are shown in Figure 19-1 through Figure 19-6. DS70318F-page 237 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 19-1: ADC BLOCK DIAGRAM FOR dsPIC33FJ06GS101 DEVICES WITH ONE SAR Even Numbered Inputs with Dedicated Sample and Hold (S&H) Circuits AN0 Eight 16-bit Registers Bus Interface SAR Core Data Format AN2 AN1 Shared Sample and Hold AN3 AN6 AN7 DS70318F-page 238 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 19-2: ADC BLOCK DIAGRAM FOR dsPIC33FJ06GS102 DEVICES WITH ONE SAR Even Numbered Inputs with Dedicated Sample and Hold (S&H) Circuits AN0 Eight 16-bit Registers Bus Interface SAR Core Data Format AN2 AN1 Shared Sample and Hold AN3 AN4 AN5 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 239 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 19-3: ADC BLOCK DIAGRAM FOR dsPIC33FJ06GS202 DEVICES WITH ONE SAR Even Numbered Inputs with Dedicated Sample and Hold (S&H) Circuits AN0 AN12(1) (EXTREF) Eight 16-bit Registers Bus Interface SAR Core Data Format AN2 AN1 Shared Sample and Hold AN3 AN4 AN5 AN13(2) (INTREF) Note 1: AN12 (EXTREF) is an internal analog input. To measure the voltage at AN12 (EXTREF), an analog comparator must be enabled and EXTREF must be selected as the comparator reference. 2: AN13 (INTREF) is an internal analog input and is not available on a pin. DS70318F-page 240 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 19-4: ADC BLOCK DIAGRAM FOR dsPIC33FJ16GS402/404 DEVICES WITH ONE SAR Even Numbered Inputs with Dedicated Sample and Hold (S&H) Circuits AN0 AN2 Ten 16-bit Registers Bus Interface SAR Core Data Format AN4 AN1 AN3 Shared Sample and Hold AN5 AN6 AN7 (c) 2008-2012 Microchip Technology Inc. DS70318F-page 241 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 19-5: ADC BLOCK DIAGRAM FOR dsPIC33FJ16GS502 DEVICES WITH TWO SARS Even Numbered Inputs with Dedicated Sample and Hold (S&H) Circuits AN0 Data Format SAR Core Five 16-bit Registers Data Format AN2 Five 16-bit Registers AN4 AN6 Bus Interface Even numbered inputs with shared S&H AN12(1) (EXTREF) AN1 Odd Numbered Inputs with Shared S&H AN3 AN5 SAR AN7 Core AN13(2) (INTREF) Note 1: AN12 (EXTREF) is an internal analog input. To measure the voltage at AN12 (EXTREF), an analog comparator must be enabled and EXTREF must be selected as the comparator reference. 2: AN13 (INTREF) is an internal analog input and is not available on a pin. DS70318F-page 242 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 19-6: ADC BLOCK DIAGRAM FOR dsPIC33FJ16GS504 DEVICES WITH TWO SARS Even Numbered Inputs with Dedicated Sample and Hold (S&H) Circuits AN0 Data Format SAR Core Seven 16-bit Registers Data Format AN2 Seven 16-bit Registers AN4 AN6 AN8 Bus Interface Even Numbered Inputs with Shared S&H AN10 AN12(1) (EXTREF) AN1 Odd Numbered Inputs with Shared S&H SAR AN3 Core AN5 AN7 AN9 AN11 AN13(2) (INTREF) Note 1: AN12 (EXTREF) is an internal analog input. To measure the voltage at AN12 (EXTREF), an analog comparator must be enabled and EXTREF must be selected as the comparator reference. 2: AN13 (INTREF) is an internal analog input and is not available on a pin. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 243 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 19.4 ADC Control Registers The ADC module uses the following control and status registers: * * * * * * * * ADCON: Analog-to-Digital Control Register ADSTAT: Analog-to-Digital Status Register ADBASE: Analog-to-Digital Base Register ADPCFG: Analog-to-Digital Port Configuration Register ADCPC0: Analog-to-Digital Convert Pair Control Register 0 ADCPC1: Analog-to-Digital Convert Pair Control Register 1 ADCPC2: Analog-to-Digital Convert Pair Control Register 2 ADCPC3: Analog-to-Digital Convert Pair Control Register 3(1) The ADCON register controls the operation of the ADC module. The ADSTAT register displays the status of the conversion processes. The ADPCFG registers configure the port pins as analog inputs or as digital I/O. The ADCPCx registers control the triggering of the ADC conversions. See Register 19-1 through Register 19-8 for detailed bit configurations. Note: A unique feature of the ADC module is its ability to sample inputs in an asynchronous manner. Individual sample and hold circuits can be triggered independently of each other. DS70318F-page 244 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-1: R/W-0 ADCON: ANALOG-TO-DIGITAL CONTROL REGISTER U-0 ADON -- R/W-0 ADSIDL R/W-0 SLOWCLK (1) U-0 R/W-0 U-0 R/W-0 -- GSWTRG -- FORM(1) bit 15 bit 8 R/W-0 EIE(1) R/W-0 R/W-0 R/W-0 U-0 ORDER(1,2) SEQSAMP(1,2) ASYNCSAMP(1) R/W-0 -- R/W-1 R/W-1 ADCS<2:0>(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 ADON: Analog-to-Digital Operating Mode bit 1 = Analog-to-Digital Converter (ADC) module is operating 0 = ADC converter is off bit 14 Unimplemented: Read as `0' bit 13 ADSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode bit 12 SLOWCLK: Enable The Slow Clock Divider bit(1) 1 = ADC is clocked by the auxiliary PLL (ACLK) 0 = ADC is clock by the primary PLL (FVCO) bit 11 Unimplemented: Read as `0' bit 10 GSWTRG: Global Software Trigger bit When this bit is set by the user, it will trigger conversions if selected by the TRGSRC<4:0> bits in the ADCPCx registers. This bit must be cleared by the user prior to initiating another global trigger (i.e., this bit is not auto-clearing). bit 9 Unimplemented: Read as `0' bit 8 FORM: Data Output Format bit(1) 1 = Fractional (DOUT = dddd dddd dd00 0000) 0 = Integer (DOUT = 0000 00dd dddd dddd) bit 7 EIE: Early Interrupt Enable bit(1) 1 = Interrupt is generated after first conversion is completed 0 = Interrupt is generated after second conversion is completed bit 6 ORDER: Conversion Order bit(1,2) 1 = Odd numbered analog input is converted first, followed by conversion of even numbered input 0 = Even numbered analog input is converted first, followed by conversion of odd numbered input bit 5 SEQSAMP: Sequential Sample Enable bit(1,2) 1 = Shared Sample and Hold (S&H) circuit is sampled at the start of the second conversion if ORDER = 0. If ORDER = 1, then the shared S&H is sampled at the start of the first conversion. 0 = Shared S&H is sampled at the same time the dedicated S&H is sampled if the shared S&H is not currently busy with an existing conversion process. If the shared S&H is busy at the time the dedicated S&H is sampled, then the shared S&H will sample at the start of the new conversion cycle. bit 4 ASYNCSAMP: Asynchronous Dedicated S&H Sampling Enable bit(1) 1 = The dedicated S&H is constantly sampling and then terminates sampling as soon as the trigger pulse is detected. 0 = The dedicated S&H starts sampling when the trigger event is detected and completes the sampling process in two ADC clock cycles. Note 1: This control bit can only be changed while ADC is disabled (ADON = 0). 2: This bit is only available on devices with one SAR. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 245 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-1: ADCON: ANALOG-TO-DIGITAL CONTROL REGISTER (CONTINUED) bit 3 Unimplemented: Read as `0' bit 2-0 ADCS<2:0>: Analog-to-Digital Conversion Clock Divider Select bits(1) 111 = FADC/8 110 = FADC/7 101 = FADC/6 100 = FADC/5 011 = FADC/4 (default) 010 = FADC/3 001 = FADC/2 000 = FADC/1 Note 1: This control bit can only be changed while ADC is disabled (ADON = 0). 2: This bit is only available on devices with one SAR. DS70318F-page 246 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-2: ADSTAT: ANALOG-TO-DIGITAL STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 U-0 R/C-0, HS R/C-0, HS R/C-0, HS R/C-0, HS R/C-0, HS R/C-0, HS R/C-0, HS -- P6RDY P5RDY P4RDY P3RDY P2RDY P1RDY P0RDY bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR C = Clearable bit `1' = Bit is set HS = Hardware Settable bit `0' = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as `0' bit 6 P6RDY: Conversion Data for Pair 6 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. bit 5 P5RDY: Conversion Data for Pair 5 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. bit 4 P4RDY: Conversion Data for Pair 4 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. bit 3 P3RDY: Conversion Data for Pair 3 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. bit 2 P2RDY: Conversion Data for Pair 2 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. bit 1 P1RDY: Conversion Data for Pair 1 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. bit 0 P0RDY: Conversion Data for Pair 0 Ready bit Bit is set when data is ready in buffer, cleared when a `0' is written to this bit. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 247 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-3: R/W-0 ADBASE: ANALOG-TO-DIGITAL BASE REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADBASE<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 ADBASE<7:1> -- bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-1 ADBASE<15:1>: This register contains the base address of the user's ADC Interrupt Service Routine jump table. This register, when read, contains the sum of the ADBASE register contents and the encoded value of the PxRDY status bits. The encoder logic provides the bit number of the highest priority PxRDY bits where P0RDY is the highest priority, and P6RDY is the lowest priority. bit 0 Unimplemented: Read as `0' Note 1: The encoding results are shifted left two bits so bits 1-0 of the result are always zero. 2: As an alternative to using the ADBASE Register, the ADCP0-6 ADC Pair Conversion Complete Interrupts can be used to invoke A to D conversion completion routines for individual ADC input pairs. REGISTER 19-4: ADPCFG: ANALOG-TO-DIGITAL PORT CONFIGURATION REGISTER U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- -- -- PCFG11 PCFG10 PCFG9 PCFG8 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PCFG7 PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-12 Unimplemented: Read as `0' bit 11-0 PCFG11:PCFG0: Analog-to-Digital Port Configuration Control bits(1) 1 = Port pin in Digital mode, port read input enabled, Analog-to-Digital input multiplexor connected to AVSS 0 = Port pin in Analog mode, port read input disabled, Analog-to-Digital samples pin voltage Note 1: Not all PCFGx bits are available on all devices. See Figure 19-1 through Figure 19-6 for the available analog pins (PCFGx = ANx, where x = 0-11). DS70318F-page 248 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-5: ADCPC0: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 0 R/W-0 R/W-0 R/W-0 IRQEN1 PEND1 SWTRG1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC1<4:0> bit 15 bit 8 R/W-0 R/W-0 R/W-0 IRQEN0 PEND0 SWTRG0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC0<4:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 IRQEN1: Interrupt Request Enable 1 bit 1 = Enable IRQ generation when requested conversion of channels AN3 and AN2 is completed 0 = IRQ is not generated bit 14 PEND1: Pending Conversion Status 1 bit 1 = Conversion of channels AN3 and AN2 is pending. Set when selected trigger is asserted 0 = Conversion is complete bit 13 SWTRG1: Software Trigger 1 bit 1 = Start conversion of AN3 and AN2 (if selected in TRGSRC bits)(1) This bit is automatically cleared by hardware when the PEND1 bit is set. 0 = Conversion is not started Note 1: The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 249 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-5: ADCPC0: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 0 (CONTINUED) bit 12-8 TRGSRC1<4:0>: Trigger 1 Source Selection bits Selects trigger source for conversion of analog channels AN3 and AN2. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled bit 7 IRQEN0: Interrupt Request Enable 0 bit 1 = Enable IRQ generation when requested conversion of channels AN1 and AN0 is completed 0 = IRQ is not generated bit 6 PEND0: Pending Conversion Status 0 bit 1 = Conversion of channels AN1 and AN0 is pending; set when selected trigger is asserted 0 = Conversion is complete bit 5 SWTRG0: Software Trigger 0 bit 1 = Start conversion of AN1 and AN0 (if selected by TRGSRC bits)(1) This bit is automatically cleared by hardware when the PEND0 bit is set. 0 = Conversion is not started Note 1: The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. DS70318F-page 250 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-5: bit 4-0 Note 1: ADCPC0: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 0 (CONTINUED) TRGSRC0<4:0>: Trigger 0 Source Selection bits Selects trigger source for conversion of analog channels AN1 and AN0. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 251 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-6: ADCPC1: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 IRQEN3(1) PEND3(1) SWTRG3(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC3<4:0>(1) bit 15 bit 8 R/W-0 R/W-0 IRQEN2(2) PEND2 (2) R/W-0 R/W-0 (2) SWTRG2 R/W-0 R/W-0 TRGSRC2<4:0> R/W-0 R/W-0 (2) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 IRQEN3: Interrupt Request Enable 3 bit(1) 1 = Enable IRQ generation when requested conversion of channels AN7 and AN6 is completed 0 = IRQ is not generated bit 14 PEND3: Pending Conversion Status 3 bit(1) 1 = Conversion of channels AN7 and AN6 is pending. Set when selected trigger is asserted 0 = Conversion is complete bit 13 SWTRG3: Software Trigger 3 bit(1) 1 = Start conversion of AN7 and AN6 (if selected in TRGSRC bits)(3) This bit is automatically cleared by hardware when the PEND3 bit is set. 0 = Conversion is not started Note 1: 2: 3: These bits are available in the dsPIC33FJ16GS402/404, dsPIC33FJ16GS504, dsPIC33FJ16GS502 and dsPIC33FJ06GS101 devices only. These bits are available in the dsPIC33FJ16GS502, dsPIC33FJ16GS504, dsPIC33FJ06GS102, dsPIC33FJ06GS202 and dsPIC33FJ16GS402/404 devices only. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. DS70318F-page 252 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-6: ADCPC1: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 1 (CONTINUED) bit 12-8 TRGSRC3<4:0>: Trigger 3 Source Selection bits(1) Selects trigger source for conversion of analog channels AN7 and AN6. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled bit 7 IRQEN2: Interrupt Request Enable 2 bit(2) 1 = Enable IRQ generation when requested conversion of channels AN5 and AN4 is completed 0 = IRQ is not generated bit 6 PEND2: Pending Conversion Status 2 bit(2) 1 = Conversion of channels AN5 and AN4 is pending; set when selected trigger is asserted. 0 = Conversion is complete bit 5 SWTRG2: Software Trigger 2 bit(2) 1 = Start conversion of AN5 and AN4 (if selected by TRGSRC bits)(3) This bit is automatically cleared by hardware when the PEND2 bit is set. 0 = Conversion is not started Note 1: 2: 3: These bits are available in the dsPIC33FJ16GS402/404, dsPIC33FJ16GS504, dsPIC33FJ16GS502 and dsPIC33FJ06GS101 devices only. These bits are available in the dsPIC33FJ16GS502, dsPIC33FJ16GS504, dsPIC33FJ06GS102, dsPIC33FJ06GS202 and dsPIC33FJ16GS402/404 devices only. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 253 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-6: bit 4-0 ADCPC1: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 1 (CONTINUED) TRGSRC2<4:0>: Trigger 2 Source Selection bits Selects trigger source for conversion of analog channels AN5 and AN4. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled Note 1: 2: 3: These bits are available in the dsPIC33FJ16GS402/404, dsPIC33FJ16GS504, dsPIC33FJ16GS502 and dsPIC33FJ06GS101 devices only. These bits are available in the dsPIC33FJ16GS502, dsPIC33FJ16GS504, dsPIC33FJ06GS102, dsPIC33FJ06GS202 and dsPIC33FJ16GS402/404 devices only. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. DS70318F-page 254 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-7: ADCPC2: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 IRQEN5 PEND5 SWTRG5 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC5<4:0> bit 15 bit 8 R/W-0 R/W-0 R/W-0 IRQEN4 PEND4 SWTRG4 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC4<4:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 IRQEN5: Interrupt Request Enable 5 bit 1 = Enable IRQ generation when requested conversion of channels AN11 and AN10 is completed 0 = IRQ is not generated bit 14 PEND5: Pending Conversion Status 5 bit 1 = Conversion of channels AN11 and AN10 is pending; set when selected trigger is asserted 0 = Conversion is complete bit 13 SWTRG5: Software Trigger 5 bit 1 = Start conversion of AN11 and AN10 (if selected in TRGSRC bits)(2) This bit is automatically cleared by hardware when the PEND5 bit is set. 0 = Conversion is not started Note 1: 2: This register is only implemented on the dsPIC33FJ16GS504 devices. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 255 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-7: ADCPC2: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 2 (CONTINUED) bit 12-8 TRGSRC5<4:0>: Trigger 5 Source Selection bits Selects trigger source for conversion of analog channels AN11 and AN10. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled bit 7 IRQEN4: Interrupt Request Enable 4 bit 1 = Enable IRQ generation when requested conversion of channels AN9 and AN8 is completed 0 = IRQ is not generated bit 6 PEND4: Pending Conversion Status 4 bit 1 = Conversion of channels AN9 and AN8 is pending; set when selected trigger is asserted 0 = Conversion is complete bit 5 SWTRG4: Software Trigger4 bit 1 = Start conversion of AN9 and AN8 (if selected by TRGSRC bits)(2) This bit is automatically cleared by hardware when the PEND4 bit is set. 0 = Conversion is not started Note 1: 2: This register is only implemented on the dsPIC33FJ16GS504 devices. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. DS70318F-page 256 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-7: bit 4-0 Note 1: 2: ADCPC2: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 2 (CONTINUED) TRGSRC4<4:0>: Trigger 4 Source Selection bits Selects trigger source for conversion of analog channels AN9 and AN8. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled This register is only implemented on the dsPIC33FJ16GS504 devices. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, then conversion will be performed when the conversion resources are available. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 257 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-8: ADCPC3: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 3(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- -- -- bit 15 bit 8 R/W-0 R/W-0 R/W-0 IRQEN6 PEND6 SWTRG6 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TRGSRC6<4:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as `0' bit 7 IRQEN6: Interrupt Request Enable 6 bit 1 = Enable IRQ generation when requested conversion of channels AN13 and AN12 is completed 0 = IRQ is not generated bit 6 PEND6: Pending Conversion Status 6 bit 1 = Conversion of channels AN13 and AN 12 is pending; set when selected trigger is asserted 0 = Conversion is complete bit 5 SWTRG6: Software Trigger 6 bit 1 = Start conversion of AN13 (INTREF) and AN12 (EXTREF) (if selected by TRGSRC bits)(2) This bit is automatically cleared by hardware when the PEND6 bit is set. 0 = Conversion is not started Note 1: 2: This register is only implemented on the dsPIC33FJ16GS502 and dsPIC33FJ16GS504 devices. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, conversion will be performed when the conversion resources are available. DS70318F-page 258 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 19-8: bit 4-0 Note 1: 2: ADCPC3: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 3(1) (CONTINUED) TRGSRC6<4:0>: Trigger 6 Source Selection bits Selects trigger source for conversion of analog channels AN13 and AN12. 11111 = Timer2 period match * * * 11011 = Reserved 11010 = PWM Generator 4 current-limit ADC trigger 11001 = PWM Generator 3 current-limit ADC trigger 11000 = PWM Generator 2 current-limit ADC trigger 10111 = PWM Generator 1 current-limit ADC trigger 10110 = Reserved * * * 10010 = Reserved 10001 = PWM Generator 4 secondary trigger selected 10000 = PWM Generator 3 secondary trigger selected 01111 = PWM Generator 2 secondary trigger selected 01110 = PWM Generator 1 secondary trigger selected 01101 = Reserved 01100 = Timer1 period match * * * 01000 = Reserved 00111 = PWM Generator 4 primary trigger selected 00110 = PWM Generator 3 primary trigger selected 00101 = PWM Generator 2 primary trigger selected 00100 = PWM Generator 1 primary trigger selected 00011 = PWM Special Event Trigger selected 00010 = Global software trigger selected 00001 = Individual software trigger selected 00000 = No conversion enabled This register is only implemented on the dsPIC33FJ16GS502 and dsPIC33FJ16GS504 devices. The trigger source must be set as global software trigger prior to setting this bit to `1'. If other conversions are in progress, conversion will be performed when the conversion resources are available. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 259 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 260 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 20.0 HIGH-SPEED ANALOG COMPARATOR * * * * Programmable output polarity Interrupt generation capability DACOUT pin to provide DAC output DAC has three ranges of operation: - AVDD/2 - Internal Reference (INTREF) - External Reference (EXTREF) * ADC sample and convert trigger capability * Disable capability reduces power consumption * Functional support for PWM module: - PWM duty cycle control - PWM period control - PWM Fault detect Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families of devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to Section 45. "High-Speed Analog Comparator" (DS70296) in the "dsPIC33F/PIC24H Family Reference Manual", which is available on the Microchip web site (www.microchip.com). 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. 20.2 Figure 20-1 shows a functional block diagram of one analog comparator from the SMPS comparator module. The analog comparator provides high-speed operation with a typical delay of 20 ns. The comparator has a typical offset voltage of 5 mV. The negative input of the comparator is always connected to the DAC circuit. The positive input of the comparator is connected to an analog multiplexer that selects the desired source pin. The dsPIC33F SMPS Comparator module monitors current and/or voltage transients that may be too fast for the CPU and ADC to capture. 20.1 Features Overview The analog comparator input pins are typically shared with pins used by the Analog-to-Digital Converter (ADC) module. Both the comparator and the ADC can use the same pins at the same time. This capability enables a user to measure an input voltage with the ADC and detect voltage transients with the comparator. The SMPS comparator module contains the following major features: * 16 selectable comparator inputs * Up to four analog comparators * 10-bit DAC for each analog comparator FIGURE 20-1: COMPARATOR MODULE BLOCK DIAGRAM INSEL<1:0> ACMPx (Trigger to PWM)(1) CMPxA(1) Status CMPxB(1) M U X (1) CMPxC CMPx(1) CMPxD 1 RANGE AVDD/2 0 Glitch Filter (1) INTREF(2) Module Description M U X CMPPOL DACOUT DAC AVSS Pulse Generator Interrupt Request 10 CMREF DACOE EXTREF(2) Note 1: 2: x = 1, 2, 3, and 4. For the INTREF and EXTREF values, refer to the DAC Module Specifications (Table 24-43) in Section 24.0 "Electrical Characteristics". (c) 2008-2012 Microchip Technology Inc. DS70318F-page 261 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 20.3 Module Applications 20.5 Interaction with I/O Buffers This module provides a means for the SMPS dsPIC DSC devices to monitor voltage and currents in a power conversion application. The ability to detect transient conditions and stimulate the dsPIC DSC processor and/or peripherals, without requiring the processor and ADC to constantly monitor voltages or currents, frees the dsPIC DSC to perform other tasks. If the comparator module is enabled and a pin has been selected as the source for the comparator, then the chosen I/O pad must disable the digital input buffer associated with the pad to prevent excessive currents in the digital buffer due to analog input voltages. The comparator module has a high-speed comparator and an associated 10-bit DAC that provides a programmable reference voltage to the inverting input of the comparator. The polarity of the comparator output is user-programmable. The output of the module can be used in the following modes: The CMPCONx register (see Register 20-1) provides the control logic that configures the comparator module. The digital logic provides a glitch filter for the comparator output to mask transient signals in less than two instruction cycles. In Sleep or Idle mode, the glitch filter is bypassed to enable an asynchronous path from the comparator to the interrupt controller. This asynchronous path can be used to wake-up the processor from Sleep or Idle mode. * * * * * Generate an Interrupt Trigger an ADC Sample and Convert Process Truncate the PWM Signal (current limit) Truncate the PWM Period (current minimum) Disable the PWM Outputs (Fault latch) The output of the comparator module may be used in multiple modes at the same time, such as: 1) generate an interrupt, 2) have the ADC take a sample and convert it, and 3) truncate the PWM output in response to a voltage being detected beyond its expected value. The comparator module can also be used to wake-up the system from Sleep or Idle mode when the analog input voltage exceeds the programmed threshold voltage. 20.4 DAC The range of the DAC is controlled through an analog multiplexer that selects either AVDD/2, an internal reference source, INTREF, or an external reference source, EXTREF. The full range of the DAC (AVDD/2) will typically be used when the chosen input source pin is shared with the ADC. The reduced range option (INTREF) will likely be used when monitoring current levels using a current sense resistor. Usually, the measured voltages in such applications are small (<1.25V); therefore the option of using a reduced reference range for the comparator extends the available DAC resolution in these applications. The use of an external reference enables the user to connect to a reference that better suits their application. DACOUT, shown in Figure 20-1, can only be associated with a single comparator at a given time. Note: It should be ensured in software that multiple DACOE bits are not set. The output on the DACOUT pin will be indeterminate if multiple comparators enable the DAC output. 20.6 Digital Logic The comparator can be disabled while in Idle mode if the CMPSIDL bit is set. If a device has multiple comparators, if any CMPSIDL bit is set, then the entire group of comparators will be disabled while in Idle mode. This behavior reduces complexity in the design of the clock control logic for this module. The digital logic also provides a one TCY width pulse generator for triggering the ADC and generating interrupt requests. The CMPDACx (see Register 20-2) register provides the digital input value to the reference DAC. If the module is disabled, the DAC and comparator are disabled to reduce power consumption. 20.7 Comparator Input Range The comparator has a limitation for the input Common Mode Range (CMR) of (AVDD - 1.5V), typical. This means that both inputs should not exceed this range. As long as one of the inputs is within the Common Mode Range, the comparator output will be correct. However, any input exceeding the CMR limitation will cause the comparator input to be saturated. If both inputs exceed the CMR, the comparator output will be indeterminate. 20.8 DAC Output Range The DAC has a limitation for the maximum reference voltage input of (AVDD - 1.6) volts. An external reference voltage input should not exceed this value or the reference DAC output will become indeterminate. 20.9 Comparator Registers The comparator module is controlled by the following registers: * CMPCONx: Comparator Control Register * CMPDACx: Comparator DAC Control Register DS70318F-page 262 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 20-1: CMPCONx: COMPARATOR CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 CMPON -- CMPSIDL -- -- -- -- DACOE bit 15 bit 8 R/W-0 R/W-0 INSEL<1:0> R/W-0 U-0 R/W-0 U-0 R/W-0 R/W-0 EXTREF -- CMPSTAT -- CMPPOL RANGE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15 CMPON: Comparator Operating Mode bit 1 = Comparator module is enabled 0 = Comparator module is disabled (reduces power consumption) bit 14 Unimplemented: Read as `0' bit 13 CMPSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode. 0 = Continue module operation in Idle mode If a device has multiple comparators, any CMPSIDL bit set to `1' disables ALL comparators while in Idle mode. bit 12-9 Reserved: Read as `0' bit 8 DACOE: DAC Output Enable 1 = DAC analog voltage is output to DACOUT pin(1) 0 = DAC analog voltage is not connected to DACOUT pin bit 7-6 INSEL<1:0>: Input Source Select for Comparator bits 00 = Select CMPxA input pin 01 = Select CMPxB input pin 10 = Select CMPxC input pin 11 = Select CMPxD input pin bit 5 EXTREF: Enable External Reference bit 1 = External source provides reference to DAC (maximum DAC voltage determined by external voltage source) 0 = Internal reference sources provide reference to DAC (maximum DAC voltage determined by RANGE bit setting) bit 4 Reserved: Read as `0' bit 3 CMPSTAT: Current State of Comparator Output Including CMPPOL Selection bit bit 2 Reserved: Read as `0' bit 1 CMPPOL: Comparator Output Polarity Control bit 1 = Output is inverted 0 = Output is non-inverted bit 0 RANGE: Selects DAC Output Voltage Range bit 1 = High Range: Max DAC Value = AVDD/2, 1.65V at 3.3V AVDD 0 = Low Range: Max DAC Value = INTREF(2) Note 1: 2: DACOUT can be associated only with a single comparator at any given time. The software must ensure that multiple comparators do not enable the DAC output by setting their respective DACOE bit. Refer to the DAC Module Specifications (Table 24-43) in Section 24.0 "Electrical Characteristics" for the INTREF value. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 263 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 REGISTER 20-2: CMPDACx: COMPARATOR DAC CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 -- -- -- -- -- -- R/W-0 R/W-0 CMREF<9:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CMREF<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown bit 15-10 Reserved: Read as `0' bit 9-0 CMREF<9:0>: Comparator Reference Voltage Select bits 1111111111 = (CMREF * INTREF/1024) or (CMREF * (AVDD/2)/1024) volts depending on RANGE bit or (CMREF * EXTREF/1024) if EXTREF is set * * * 0000000000 = 0.0 volts DS70318F-page 264 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 21.0 SPECIAL FEATURES 21.1 Note 1: This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the "dsPIC33F/PIC24H Family Reference Manual". Please see the Microchip web site (www.microchip.com) for the latest "dsPIC33F/PIC24H Family Reference Manual" sections. 2: Some registers and associated bits described in this section may not be available on all devices. Refer to Section 4.0 "Memory Organization" in this data sheet for device-specific register and bit information. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices include several features intended to maximize application flexibility and reliability, and minimize cost through elimination of external components. These are: * * * * * * * Configuration Bits The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices provide non-volatile memory implementations for device Configuration bits. Refer to Section 25. "Device Configuration" (DS70194) in the "dsPIC33F/PIC24H Family Reference Manual" for more information on this implementation. The Configuration bits can be programmed (read as `0'), or left unprogrammed (read as `1'), to select various device configurations. These bits are mapped starting at program memory location 0xF80000. The individual Configuration bit descriptions for the Configuration registers are shown in Table 21-2. Note that address, 0xF80000, is beyond the user program memory space. It belongs to the configuration memory space (0x800000-0xFFFFFF), which can only be accessed using table reads and table writes. The device Configuration register map is shown in Table 21-1. Flexible Configuration Watchdog Timer (WDT) Code Protection and CodeGuardTM Security JTAG Boundary Scan Interface In-Circuit Serial ProgrammingTM (ICSPTM) In-Circuit Emulation Brown-out Reset (BOR) TABLE 21-1: Address DEVICE CONFIGURATION REGISTER MAP Name Bit 7 Bit 6 Bit 5 Bit 4 0xF80000 FBS -- -- -- -- 0xF80002 Reserved -- -- -- -- -- -- -- -- IESO -- -- 0xF80004 FGS 0xF80006 FOSCSEL Bit 3 -- FCKSM<1:0> IOL1WAY -- -- WDTPRE -- -- Reserved(2) JTAGEN -- -- 0xF8000E FICD -- -- GSS<1:0> -- GWRP FNOSC<2:0> FWDTEN WINDIS Reserved(1) Bit 0 BWRP -- -- 0xF80008 FOSC -- Bit 1 BSS<2:0> -- 0xF8000A FWDT 0xF8000C FPOR Bit 2 -- OSCIOFNC POSCMD<1:0> WDTPOST<3:0> 0xF80010 FUID0 User Unit ID Byte 0 0xF80012 FUID1 User Unit ID Byte 1 FPWRT<2:0> -- ICS<1:0> Legend: -- = unimplemented bit, read as `0'. Note 1: These bits are reserved for use by development tools and must be programmed to `1'. 2: This bit reads the current programmed value. a 2008-2012 Microchip Technology Inc. DS70318F-page 265 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 21-2: dsPIC33F CONFIGURATION BITS DESCRIPTION Bit Field Register RTSP Effect Description BWRP FBS Immediate Boot Segment Program Flash Write Protection bit 1 = Boot segment can be written 0 = Boot segment is write-protected BSS<2:0> FBS Immediate Boot Segment Program Flash Code Protection Size bits x11 = No boot program Flash segment Boot space is 256 instruction words (except interrupt vectors) 110 = Standard security; boot program Flash segment ends at 0x0003FE 010 = High security; boot program Flash segment ends at 0x0003FE Boot space is 768 instruction words (except interrupt vectors) 101 = Standard security; boot program Flash segment ends at 0x0007FE 001 = High security; boot program Flash segment ends at 0x0007FE Boot space is 1792 instruction words (except interrupt vectors) 100 = Standard security; boot program Flash segment ends at 0x000FFE 000 = High security; boot program Flash segment ends at 0x000FFE GSS<1:0> FGS Immediate General Segment Code-Protect bits 11 = User program memory is not code-protected 10 = Standard security 0x = High security GWRP FGS Immediate General Segment Write-Protect bit 1 = User program memory is not write-protected 0 = User program memory is write-protected IESO FOSCSEL Immediate Two-speed Oscillator Start-up Enable bit 1 = Start-up device with FRC, then automatically switch to the user-selected oscillator source when ready 0 = Start-up device with user-selected oscillator source FNOSC<2:0> FOSCSEL If clock switch is enabled, RTSP effect is on any device Reset; otherwise, Immediate FCKSM<1:0> FOSC Immediate Clock Switching Mode bits 1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled IOL1WAY FOSC Immediate Peripheral Pin Select Configuration bit 1 = Allow only one reconfiguration 0 = Allow multiple reconfigurations OSCIOFNC FOSC Immediate OSC2 Pin Function bit (except in XT and HS modes) 1 = OSC2 is clock output 0 = OSC2 is general purpose digital I/O pin DS70318F-page 266 Initial Oscillator Source Selection bits 111 = Internal Fast RC (FRC) oscillator with postscaler 110 = Internal Fast RC (FRC) oscillator with divide-by-16 101 = LPRC oscillator 100 = Reserved 011 = Primary (XT, HS, EC) oscillator with PLL 010 = Primary (XT, HS, EC) oscillator 001 = Internal Fast RC (FRC) oscillator with PLL 000 = FRC oscillator (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 21-2: Bit Field dsPIC33F CONFIGURATION BITS DESCRIPTION (CONTINUED) Register RTSP Effect POSCMD<1:0> FOSC Immediate Primary Oscillator Mode Select bits 11 = Primary oscillator disabled 10 = HS Crystal Oscillator mode 01 = XT Crystal Oscillator mode 00 = EC (External Clock) mode FWDTEN FWDT Immediate Watchdog Timer Enable bit 1 = Watchdog Timer always enabled (LPRC oscillator cannot be disabled; clearing the SWDTEN bit in the RCON register will have no effect) 0 = Watchdog Timer enabled/disabled by user software (LPRC can be disabled by clearing the SWDTEN bit in the RCON register) WINDIS FWDT Immediate Watchdog Timer Window Enable bit 1 = Watchdog Timer in Non-Window mode 0 = Watchdog Timer in Window mode WDTPRE FWDT Immediate Watchdog Timer Prescaler bit 1 = 1:128 0 = 1:32 WDTPOST<3:0> FWDT Immediate Watchdog Timer Postscaler bits 1111 = 1:32,768 1110 = 1:16,384 * * * 0001 = 1:2 0000 = 1:1 FPWRT<2:0> FPOR Immediate Power-on Reset Timer Value Select bits 111 = PWRT = 128 ms 110 = PWRT = 64 ms 101 = PWRT = 32 ms 100 = PWRT = 16 ms 011 = PWRT = 8 ms 010 = PWRT = 4 ms 001 = PWRT = 2 ms 000 = PWRT = Disabled JTAGEN FICD Immediate JTAG Enable bit 1 = JTAG is enabled 0 = JTAG is disabled ICS<1:0> FICD Immediate ICD Communication Channel Select Enable bits 11 = Communicate on PGEC1 and PGED1 10 = Communicate on PGEC2 and PGED2 01 = Communicate on PGEC3 and PGED3 00 = Reserved, do not use. (c) 2008-2012 Microchip Technology Inc. Description DS70318F-page 267 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 21.2 On-Chip Voltage Regulator 21.3 BOR: Brown-Out Reset The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices power their core digital logic at a nominal 2.5V. This can create a conflict for designs that are required to operate at a higher typical voltage, such as 3.3V. To simplify system design, all devices in the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 families incorporate an on-chip regulator that allows the device to run its core logic from VDD. The Brown-out Reset (BOR) module is based on an internal voltage reference circuit. The main purpose of the BOR module is to generate a device Reset when a brown-out condition occurs. Brown-out conditions are generally caused by glitches on the AC mains (for example, missing portions of the AC cycle waveform due to bad power transmission lines, or voltage sags due to excessive current draw when a large inductive load is turned on). The regulator provides power to the core from the other VDD pins. When the regulator is enabled, a low-ESR (less than 5 ohms) capacitor (such as tantalum or ceramic) must be connected to the VCAP pin (Figure 21-1). This helps to maintain the stability of the regulator. The recommended value for the filter capacitor is provided in Table 24-13 located in Section 24.1 "DC Characteristics". A BOR generates a Reset pulse, which resets the device. The BOR selects the clock source, based on the device Configuration bit values (FNOSC<2:0> and POSCMD<1:0>). Note: It is important for the low-ESR capacitor to be placed as close as possible to the VCAP pin. On a POR, it takes approximately 20 s for the on-chip voltage regulator to generate an output voltage. During this time, designated as TSTARTUP, code execution is disabled. TSTARTUP is applied every time the device resumes operation after any power-down. FIGURE 21-1: CONNECTIONS FOR THE ON-CHIP VOLTAGE REGULATOR(1,2,3) If an oscillator mode is selected, the BOR activates the Oscillator Start-up Timer (OST). The system clock is held until OST expires. If the PLL is used, the clock is held until the LOCK bit (OSCCON<5>) is `1'. Concurrently, the PWRT time-out (TPWRT) is applied before the internal Reset is released. If TPWRT = 0 and a crystal oscillator is being used, then a nominal delay of TFSCM = 100 is applied. The total delay in this case is TFSCM. The BOR Status bit (RCON<1>) is set to indicate that a BOR has occurred. The BOR circuit continues to operate while in Sleep or Idle modes and resets the device should VDD fall below the BOR threshold voltage. 3.3V dsPIC33F VDD VCAP CEFC 10 F Tantalum Note 1: 2: 3: VSS These are typical operating voltages. Refer to Table 24-13 located in Section 24.1 "DC Characteristics" for the full operating ranges of VDD. It is important for the low-ESR capacitor to be placed as close as possible to the VCAP pin. Typical VCAP pin voltage = 2.5V when VDD VDDMIN. DS70318F-page 268 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 21.4 Watchdog Timer (WDT) 21.4.2 For dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices, the WDT is driven by the LPRC oscillator. When the WDT is enabled, the clock source is also enabled. 21.4.1 PRESCALER/POSTSCALER The nominal WDT clock source from LPRC is 32 kHz. This feeds a prescaler than can be configured for either 5-bit (divide-by-32) or 7-bit (divide-by-128) operation. The prescaler is set by the WDTPRE Configuration bit. With a 32 kHz input, the prescaler yields a nominal WDT time-out period (TWDT) of 1 ms in 5-bit mode, or 4 ms in 7-bit mode. A variable postscaler divides down the WDT prescaler output and allows for a wide range of time-out periods. The postscaler is controlled by the WDTPOST<3:0> Configuration bits (FWDT<3:0>) which allow the selection of 16 settings, from 1:1 to 1:32,768. Using the prescaler and postscaler, time-out periods ranging from 1 ms to 131 seconds can be achieved. The WDT, prescaler and postscaler are reset: * On any device Reset * On the completion of a clock switch, whether invoked by software (i.e., setting the OSWEN bit after changing the NOSC<2:0> bits) or by hardware (i.e., Fail-Safe Clock Monitor) * When a PWRSAV instruction is executed (i.e., Sleep or Idle mode is entered) * When the device exits Sleep or Idle mode to resume normal operation * By a CLRWDT instruction during normal execution Note: SLEEP AND IDLE MODES If the WDT is enabled, it will continue to run during Sleep or Idle modes. When the WDT time-out occurs, the device will wake the device and code execution will continue from where the PWRSAV instruction was executed. The corresponding SLEEP bit (RCON<3>) or IDLE bit (RCON<2>) will need to be cleared in software after the device wakes up. 21.4.3 ENABLING WDT The WDT is enabled or disabled by the FWDTEN Configuration bit in the FWDT Configuration register. When the FWDTEN Configuration bit is set, the WDT is always enabled. The WDT can be optionally controlled in software when the FWDTEN Configuration bit has been programmed to `0'. The WDT is enabled in software by setting the SWDTEN control bit (RCON<5>). The SWDTEN control bit is cleared on any device Reset. The software WDT option allows the user application to enable the WDT for critical code segments and disable the WDT during non-critical segments for maximum power savings. Note: If the WINDIS bit (FWDT<6>) is cleared, the CLRWDT instruction should be executed by the application software only during the last 1/4 of the WDT period. This CLRWDT window can be determined by using a timer. If a CLRWDT instruction is executed before this window, a WDT Reset occurs. The WDT flag bit, WDTO (RCON<4>), is not automatically cleared following a WDT time-out. To detect subsequent WDT events, the flag must be cleared in software. The CLRWDT and PWRSAV instructions clear the prescaler and postscaler counts when executed. FIGURE 21-2: WDT BLOCK DIAGRAM All Device Resets Transition to New Clock Source Exit Sleep or Idle Mode PWRSAV Instruction CLRWDT Instruction Watchdog Timer Sleep/Idle WDTPRE WDTPOST<3:0> WDT Wake-up SWDTEN FWDTEN RS Prescaler (Divide by N1) LPRC Clock 1 RS Postscaler (Divide by N2) 0 WINDIS WDT Reset WDT Window Select CLRWDT Instruction (c) 2008-2012 Microchip Technology Inc. DS70318F-page 269 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 21.5 JTAG Interface The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices implement a JTAG interface, which supports boundary scan device testing, as well as in-circuit programming. Detailed information on this interface will be provided in future revisions of the document. 21.6 In-Circuit Serial Programming The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 family of digital signal controllers can be serially programmed while in the end application circuit. This is done with two lines for clock and data and three other lines for power, ground and the programming sequence. Serial programming allows customers to manufacture boards with unprogrammed devices and then program the digital signal controller just before shipping the product. Serial programming also allows the most recent firmware or a custom firmware to be programmed. Refer to the "dsPIC33F/PIC24H Flash Programming Specification" (DS70152) for details about In-Circuit Serial Programming (ICSP). 21.7 In-Circuit Debugger The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices provide simple debugging functionality through the PGECx (Emulation/Debug Clock) and PGEDx (Emulation/Debug Data) pin functions. Any of the three pairs of debugging clock/data pins can be used: * PGEC1 and PGED1 * PGEC2 and PGED2 * PGEC3 and PGED3 To use the in-circuit debugger function of the device, the design must implement ICSP connections to MCLR, VDD, VSS, and the PGECx/PGEDx pin pair. In addition, when the feature is enabled, some of the resources are not available for general use. These resources include the first 80 bytes of data RAM and two I/O pins. Any of the three pairs of programming clock/data pins can be used: * PGEC1 and PGED1 * PGEC2 and PGED2 * PGEC3 and PGED3 DS70318F-page 270 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 21.8 Code Protection and CodeGuardTM Security The code protection features are controlled by the Configuration registers: FBS and FGS. The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices offer the intermediate implementation of CodeGuardTM Security. CodeGuard Security enables multiple parties to securely share resources (memory, interrupts and peripherals) on a single chip. This feature helps protect individual Intellectual Property (IP) in collaborative system designs. Secure segment and RAM protection is not implemented in dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices. Note: Refer to Section 23. "CodeGuardTM Security" (DS70199) for further information on CodeGuard Security usage, configuration and operation. When coupled with software encryption libraries, CodeGuardTM Security can be used to securely update Flash even when multiple IPs reside on a single chip. TABLE 21-3: CODE FLASH SECURITY SEGMENT SIZES FOR 6-Kbyte DEVICES Configuration Bits CODE FLASH SECURITY SEGMENT SIZES FOR 16-Kbyte DEVICES Configuration Bits VS = 256 IW BSS<2:0> = x11 0K TABLE 21-4: GS = 1792 IW 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h VS = 256 IW BSS<2:0> = x11 0K GS = 5376 IW 002BFEh VS = 256 IW BS = 256 IW BSS<2:0> = x10 GS = 1536 IW 256 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h 002BFEh VS = 256 IW BS = 256 IW BSS<2:0> = x10 256 GS = 5120 IW 002BFEh VS = 256 IW BSS<2:0> = x01 BS = 768 IW 768 GS = 1024 IW 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h VS = 256 IW BSS<2:0> = x01 BSS<2:0> = x00 BS = 1792 IW 1792 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h 002BFEh (c) 2008-2012 Microchip Technology Inc. BS = 768 IW 768 GS = 4608 IW 002BFEh VS = 256 IW 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h VS = 256 IW BSS<2:0> = x00 BS = 1792 IW 1792 GS = 3584 IW 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h 002BFEh 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h 002BFEh 000000h 0001FEh 000200h 0003FEh 000400h 0007FEh 000800h 000FFEh 001000h 002BFEh DS70318F-page 271 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 272 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 22.0 Note: INSTRUCTION SET SUMMARY This data sheet summarizes the features of the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 devices. It is not intended to be a comprehensive reference source. To complement the information in this data sheet, refer to the latest sections in the "dsPIC33F/PIC24H Family Reference Manual", which are available on the Microchip web site (www.microchip.com). The dsPIC33F instruction set is identical to that of the dsPIC30F. Most instructions are a single program memory word (24 bits). Only three instructions require two program memory locations. Each single-word instruction is a 24-bit word, divided into an 8-bit opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The instruction set is highly orthogonal and is grouped into five basic categories: * * * * * Word or byte-oriented operations Bit-oriented operations Literal operations DSP operations Control operations Table 22-1 shows the general symbols used in describing the instructions. The dsPIC33F instruction set summary in Table 22-2 lists all the instructions, along with the status flags affected by each instruction. Most word or byte-oriented W register instructions (including barrel shift instructions) have three operands: * The first source operand, which is typically a register `Wb' without any address modifier * The second source operand, which is typically a register `Ws' with or without an address modifier * The destination of the result, which is typically a register `Wd' with or without an address modifier However, word or byte-oriented file register instructions have two operands: * The file register specified by the value, `f' * The destination, which could be either the file register, `f', or the W0 register, which is denoted as `WREG' (c) 2008-2012 Microchip Technology Inc. Most bit-oriented instructions (including rotate/shift instructions) have two operands: simple * The W register (with or without an address modifier) or file register (specified by the value of `Ws' or `f') * The bit in the W register or file register (specified by a literal value or indirectly by the contents of register `Wb') The literal instructions that involve data movement can use some of the following operands: * A literal value to be loaded into a W register or file register (specified by `k') * The W register or file register where the literal value is to be loaded (specified by `Wb' or `f') However, literal instructions that involve arithmetic or logical operations use some of the following operands: * The first source operand, which is a register `Wb' without any address modifier * The second source operand, which is a literal value * The destination of the result (only if not the same as the first source operand), which is typically a register `Wd' with or without an address modifier The MAC class of DSP instructions can use some of the following operands: * The accumulator (A or B) to be used (required operand) * The W registers to be used as the two operands * The X and Y address space prefetch operations * The X and Y address space prefetch destinations * The accumulator write-back destination The other DSP instructions do not involve any multiplication and can include: * The accumulator to be used (required) * The source or destination operand (designated as Wso or Wdo, respectively) with or without an address modifier * The amount of shift specified by a W register, `Wn', or a literal value The control instructions can use some of the following operands: * A program memory address * The mode of the table read and table write instructions DS70318F-page 273 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Most instructions are a single word. Certain double-word instructions are designed to provide all the required information in these 48 bits. In the second word, the 8 MSbs are `0's. If this second word is executed as an instruction (by itself), it will execute as a NOP. The double-word instructions execute in two instruction cycles. Most single-word instructions are executed in a single instruction cycle, unless a conditional test is true, or the program counter is changed as a result of the instruction. In these cases, the execution takes two instruction cycles with the additional instruction cycle(s) executed as a NOP. Notable exceptions are the BRA TABLE 22-1: (unconditional/computed branch), indirect CALL/GOTO, all table reads and writes and RETURN/RETFIE instructions, which are single-word instructions but take two or three cycles. Certain instructions that involve skipping over the subsequent instruction require either two or three cycles if the skip is performed, depending on whether the instruction being skipped is a single-word or two-word instruction. Moreover, double-word moves require two cycles. Note: For more details on the instruction set, refer to the "16-bit MCU and DSC Programmer's Reference Manual" (DS70157). SYMBOLS USED IN OPCODE DESCRIPTIONS Field #text Description Means literal defined by "text" (text) Means "content of text" [text] Means "the location addressed by text" { } Optional field or operation Register bit field .b Byte mode selection .d Double-Word mode selection .S Shadow register select .w Word mode selection (default) Acc One of two accumulators {A, B} AWB Accumulator Write-Back Destination Address register {W13, [W13]+ = 2} bit4 4-bit bit selection field (used in word-addressed instructions) {0...15} C, DC, N, OV, Z MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero Expr Absolute address, label or expression (resolved by the linker) f File register address {0x0000...0x1FFF} lit1 1-bit unsigned literal {0,1} lit4 4-bit unsigned literal {0...15} lit5 5-bit unsigned literal {0...31} lit8 8-bit unsigned literal {0...255} lit10 10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode lit14 14-bit unsigned literal {0...16384} lit16 16-bit unsigned literal {0...65535} lit23 23-bit unsigned literal {0...8388608}; LSb must be `0' None Field does not require an entry, can be blank OA, OB, SA, SB DSP Status bits: ACCA Overflow, ACCB Overflow, ACCA Saturate, ACCB Saturate PC Program Counter Slit10 10-bit signed literal {-512...511} Slit16 16-bit signed literal {-32768...32767} Slit6 6-bit signed literal {-16...16} Wb Base W register {W0..W15} Wd Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] } Wdo Destination W register { Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] } Wm,Wn Dividend, Divisor Working register pair (Direct Addressing) DS70318F-page 274 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 22-1: SYMBOLS USED IN OPCODE DESCRIPTIONS (CONTINUED) Field Description Wm*Wm Multiplicand and Multiplier Working register pair for Square instructions {W4 * W4,W5 * W5,W6 * W6,W7 * W7} Wm*Wn Multiplicand and Multiplier Working register pair for DSP instructions {W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7} Wn One of 16 Working registers {W0..W15} Wnd One of 16 Destination Working registers {W0...W15} Wns One of 16 Source Working registers {W0...W15} WREG W0 (Working register used in file register instructions) Ws Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] } Wso Source W register { Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] } Wx X Data Space Prefetch Address register for DSP instructions {[W8] + = 6, [W8] + = 4, [W8] + = 2, [W8], [W8] - = 6, [W8] - = 4, [W8] - = 2, [W9] + = 6, [W9] + = 4, [W9] + = 2, [W9], [W9] - = 6, [W9] - = 4, [W9] - = 2, [W9 + W12], none} Wxd X Data Space Prefetch Destination register for DSP instructions {W4...W7} Wy Y Data Space Prefetch Address register for DSP instructions {[W10] + = 6, [W10] + = 4, [W10] + = 2, [W10], [W10] - = 6, [W10] - = 4, [W10] - = 2, [W11] + = 6, [W11] + = 4, [W11] + = 2, [W11], [W11] - = 6, [W11] - = 4, [W11] - = 2, [W11 + W12], none} Wyd Y Data Space Prefetch Destination register for DSP instructions {W4...W7} (c) 2008-2012 Microchip Technology Inc. DS70318F-page 275 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 22-2: Base Instr # 1 2 3 4 INSTRUCTION SET OVERVIEW Assembly Mnemonic ADD ADDC AND ASR Assembly Syntax # of # of Words Cycles Description Status Flags Affected ADD Acc Add Accumulators 1 1 ADD f f = f + WREG 1 1 OA,OB,SA,SB C,DC,N,OV,Z ADD f,WREG WREG = f + WREG 1 1 C,DC,N,OV,Z ADD #lit10,Wn Wd = lit10 + Wd 1 1 C,DC,N,OV,Z ADD Wb,Ws,Wd Wd = Wb + Ws 1 1 C,DC,N,OV,Z ADD Wb,#lit5,Wd Wd = Wb + lit5 1 1 C,DC,N,OV,Z OA,OB,SA,SB ADD Wso,#Slit4,Acc 16-bit Signed Add to Accumulator 1 1 ADDC f f = f + WREG + (C) 1 1 C,DC,N,OV,Z ADDC f,WREG WREG = f + WREG + (C) 1 1 C,DC,N,OV,Z ADDC #lit10,Wn Wd = lit10 + Wd + (C) 1 1 C,DC,N,OV,Z ADDC Wb,Ws,Wd Wd = Wb + Ws + (C) 1 1 C,DC,N,OV,Z ADDC Wb,#lit5,Wd Wd = Wb + lit5 + (C) 1 1 C,DC,N,OV,Z AND f f = f .AND. WREG 1 1 N,Z AND f,WREG WREG = f .AND. WREG 1 1 N,Z AND #lit10,Wn Wd = lit10 .AND. Wd 1 1 N,Z AND Wb,Ws,Wd Wd = Wb .AND. Ws 1 1 N,Z AND Wb,#lit5,Wd Wd = Wb .AND. lit5 1 1 N,Z ASR f f = Arithmetic Right Shift f 1 1 C,N,OV,Z ASR f,WREG WREG = Arithmetic Right Shift f 1 1 C,N,OV,Z ASR Ws,Wd Wd = Arithmetic Right Shift Ws 1 1 C,N,OV,Z ASR Wb,Wns,Wnd Wnd = Arithmetic Right Shift Wb by Wns 1 1 N,Z ASR Wb,#lit5,Wnd Wnd = Arithmetic Right Shift Wb by lit5 1 1 N,Z 1 None 5 BCLR BCLR f,#bit4 Bit Clear f 1 BCLR Ws,#bit4 Bit Clear Ws 1 1 None 6 BRA BRA C,Expr Branch if Carry 1 1 (2) None BRA GE,Expr Branch if Greater Than or Equal 1 1 (2) None BRA GEU,Expr Branch if Unsigned Greater Than or Equal 1 1 (2) None BRA GT,Expr Branch if Greater Than 1 1 (2) None BRA GTU,Expr Branch if Unsigned Greater Than 1 1 (2) None BRA LE,Expr Branch if Less Than or Equal 1 1 (2) None BRA LEU,Expr Branch if Unsigned Less Than or Equal 1 1 (2) None BRA LT,Expr Branch if Less Than 1 1 (2) None BRA LTU,Expr Branch if Unsigned Less Than 1 1 (2) None BRA N,Expr Branch if Negative 1 1 (2) None BRA NC,Expr Branch if Not Carry 1 1 (2) None BRA NN,Expr Branch if Not Negative 1 1 (2) None BRA NOV,Expr Branch if Not Overflow 1 1 (2) None BRA NZ,Expr Branch if Not Zero 1 1 (2) None BRA OA,Expr Branch if Accumulator A Overflow 1 1 (2) None BRA OB,Expr Branch if Accumulator B Overflow 1 1 (2) None BRA OV,Expr Branch if Overflow 1 1 (2) None None 7 8 9 BSET BSW BTG BRA SA,Expr Branch if Accumulator A Saturated 1 1 (2) BRA SB,Expr Branch if Accumulator B Saturated 1 1 (2) None BRA Expr Branch Unconditionally 1 2 None BRA Z,Expr Branch if Zero 1 1 (2) None BRA Wn Computed Branch 1 2 None BSET f,#bit4 Bit Set f 1 1 None BSET Ws,#bit4 Bit Set Ws 1 1 None BSW.C Ws,Wb Write C bit to Ws 1 1 None BSW.Z Ws,Wb Write Z bit to Ws 1 1 None BTG f,#bit4 Bit Toggle f 1 1 None BTG Ws,#bit4 Bit Toggle Ws 1 1 None DS70318F-page 276 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 22-2: Base Instr # 10 11 12 13 INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Mnemonic BTSC BTSS BTST BTSTS Assembly Syntax Description # of # of Words Cycles Status Flags Affected BTSC f,#bit4 Bit Test f, Skip if Clear 1 1 (2 or 3) None BTSC Ws,#bit4 Bit Test Ws, Skip if Clear 1 1 (2 or 3) None BTSS f,#bit4 Bit Test f, Skip if Set 1 1 (2 or 3) None BTSS Ws,#bit4 Bit Test Ws, Skip if Set 1 1 (2 or 3) None BTST f,#bit4 Bit Test f 1 1 Z BTST.C Ws,#bit4 Bit Test Ws to C 1 1 C BTST.Z Ws,#bit4 Bit Test Ws to Z 1 1 Z BTST.C Ws,Wb Bit Test Ws to C 1 1 C Z BTST.Z Ws,Wb Bit Test Ws to Z 1 1 BTSTS f,#bit4 Bit Test then Set f 1 1 Z BTSTS.C Ws,#bit4 Bit Test Ws to C, then Set 1 1 C BTSTS.Z Ws,#bit4 Bit Test Ws to Z, then Set 1 1 Z 14 CALL CALL lit23 Call Subroutine 2 2 None CALL Wn Call Indirect Subroutine 1 2 None 15 CLR CLR f f = 0x0000 1 1 None CLR WREG WREG = 0x0000 1 1 None CLR Ws Ws = 0x0000 1 1 None CLR Acc,Wx,Wxd,Wy,Wyd,AWB Clear Accumulator 1 1 OA,OB,SA,SB Clear Watchdog Timer 1 1 WDTO,Sleep 16 CLRWDT 17 COM 18 19 20 CP CP0 CPB CLRWDT COM f f=f 1 1 N,Z COM f,WREG WREG = f 1 1 N,Z COM Ws,Wd Wd = Ws 1 1 N,Z CP f Compare f with WREG 1 1 C,DC,N,OV,Z CP Wb,#lit5 Compare Wb with lit5 1 1 C,DC,N,OV,Z CP Wb,Ws Compare Wb with Ws (Wb - Ws) 1 1 C,DC,N,OV,Z CP0 f Compare f with 0x0000 1 1 C,DC,N,OV,Z CP0 Ws Compare Ws with 0x0000 1 1 C,DC,N,OV,Z CPB f Compare f with WREG, with Borrow 1 1 C,DC,N,OV,Z CPB Wb,#lit5 Compare Wb with lit5, with Borrow 1 1 C,DC,N,OV,Z CPB Wb,Ws Compare Wb with Ws, with Borrow (Wb - Ws - C) 1 1 C,DC,N,OV,Z 21 CPSEQ CPSEQ Wb, Wn Compare Wb with Wn, Skip if = 1 1 (2 or 3) None 22 CPSGT CPSGT Wb, Wn Compare Wb with Wn, Skip if > 1 1 (2 or 3) None 23 CPSLT CPSLT Wb, Wn Compare Wb with Wn, Skip if < 1 1 (2 or 3) None 24 CPSNE CPSNE Wb, Wn Compare Wb with Wn, Skip if 1 1 (2 or 3) None 25 DAW DAW Wn Wn = Decimal Adjust Wn 1 1 C 26 DEC DEC f f=f-1 1 1 C,DC,N,OV,Z DEC f,WREG WREG = f - 1 1 1 C,DC,N,OV,Z DEC Ws,Wd Wd = Ws - 1 1 1 C,DC,N,OV,Z DEC2 f f=f-2 1 1 C,DC,N,OV,Z DEC2 f,WREG WREG = f - 2 1 1 C,DC,N,OV,Z DEC2 Ws,Wd Wd = Ws - 2 1 1 C,DC,N,OV,Z DISI #lit14 Disable Interrupts for k Instruction Cycles 1 1 None 27 28 DEC2 DISI (c) 2008-2012 Microchip Technology Inc. DS70318F-page 277 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 22-2: Base Instr # 29 INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Mnemonic DIV Assembly Syntax # of # of Words Cycles Description Status Flags Affected DIV.S Wm,Wn Signed 16/16-bit Integer Divide 1 18 N,Z,C,OV DIV.SD Wm,Wn Signed 32/16-bit Integer Divide 1 18 N,Z,C,OV DIV.U Wm,Wn Unsigned 16/16-bit Integer Divide 1 18 N,Z,C,OV DIV.UD Wm,Wn Unsigned 32/16-bit Integer Divide 1 18 N,Z,C,OV Signed 16/16-bit Fractional Divide 1 18 N,Z,C,OV None 30 DIVF DIVF 31 DO DO #lit14,Expr Do code to PC + Expr, lit14 + 1 times 2 2 DO Wn,Expr Do code to PC + Expr, (Wn) + 1 times 2 2 None Wm,Wn 32 ED ED Wm*Wm,Acc,Wx,Wy,Wxd Euclidean Distance (no accumulate) 1 1 OA,OB,OAB, SA,SB,SAB 33 EDAC EDAC Wm*Wm,Acc,Wx,Wy,Wxd Euclidean Distance 1 1 OA,OB,OAB, SA,SB,SAB 34 EXCH EXCH Wns,Wnd Swap Wns with Wnd 1 1 None 35 FBCL FBCL Ws,Wnd Find Bit Change from Left (MSb) Side 1 1 C 36 FF1L FF1L Ws,Wnd Find First One from Left (MSb) Side 1 1 C 37 FF1R FF1R Ws,Wnd Find First One from Right (LSb) Side 1 1 C 38 GOTO GOTO Expr Go to Address 2 2 None GOTO Wn Go to Indirect 1 2 None INC f f=f+1 1 1 C,DC,N,OV,Z INC f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z C,DC,N,OV,Z 39 40 41 INC INC2 IOR INC Ws,Wd Wd = Ws + 1 1 1 INC2 f f=f+2 1 1 C,DC,N,OV,Z INC2 f,WREG WREG = f + 2 1 1 C,DC,N,OV,Z INC2 Ws,Wd Wd = Ws + 2 1 1 C,DC,N,OV,Z IOR f f = f .IOR. WREG 1 1 N,Z IOR f,WREG WREG = f .IOR. WREG 1 1 N,Z IOR #lit10,Wn Wd = lit10 .IOR. Wd 1 1 N,Z IOR Wb,Ws,Wd Wd = Wb .IOR. Ws 1 1 N,Z IOR Wb,#lit5,Wd Wd = Wb .IOR. lit5 1 1 N,Z OA,OB,OAB, SA,SB,SAB 42 LAC LAC Wso,#Slit4,Acc Load Accumulator 1 1 43 LNK LNK #lit14 Link Frame Pointer 1 1 None 44 LSR LSR f f = Logical Right Shift f 1 1 C,N,OV,Z LSR f,WREG WREG = Logical Right Shift f 1 1 C,N,OV,Z LSR Ws,Wd Wd = Logical Right Shift Ws 1 1 C,N,OV,Z LSR Wb,Wns,Wnd Wnd = Logical Right Shift Wb by Wns 1 1 N,Z LSR Wb,#lit5,Wnd Wnd = Logical Right Shift Wb by lit5 1 1 N,Z MAC Wm*Wn,Acc,Wx,Wxd,Wy,Wyd , AWB Multiply and Accumulate 1 1 OA,OB,OAB, SA,SB,SAB MAC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Square and Accumulate 1 1 OA,OB,OAB, SA,SB,SAB MOV f,Wn Move f to Wn 1 1 None MOV f Move f to f 1 1 N,Z MOV f,WREG Move f to WREG 1 1 None 45 46 47 MAC MOV MOVSAC MOV #lit16,Wn Move 16-bit Literal to Wn 1 1 None MOV.b #lit8,Wn Move 8-bit Literal to Wn 1 1 None MOV Wn,f Move Wn to f 1 1 None MOV Wso,Wdo Move Ws to Wd 1 1 None MOV WREG,f None Move WREG to f 1 1 MOV.D Wns,Wd Move Double from W(ns):W(ns + 1) to Wd 1 2 None MOV.D Ws,Wnd Move Double from Ws to W(nd + 1):W(nd) 1 2 None Prefetch and Store Accumulator 1 1 None MOVSAC DS70318F-page 278 Acc,Wx,Wxd,Wy,Wyd,AWB (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 22-2: Base Instr # 48 INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Mnemonic MPY Assembly Syntax Description # of # of Words Cycles Status Flags Affected MPY Wm*Wn,Acc,Wx,Wxd,Wy,Wyd Multiply Wm by Wn to Accumulator 1 1 OA,OB,OAB, SA,SB,SAB MPY Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Square Wm to Accumulator 1 1 OA,OB,OAB, SA,SB,SAB 49 MPY.N MPY.N Wm*Wn,Acc,Wx,Wxd,Wy,Wyd -(Multiply Wm by Wn) to Accumulator 1 1 None 50 MSC MSC Wm*Wm,Acc,Wx,Wxd,Wy,Wyd , AWB Multiply and Subtract from Accumulator 1 1 OA,OB,OAB, SA,SB,SAB 51 MUL MUL.SS Wb,Ws,Wnd {Wnd + 1, Wnd} = signed(Wb) * signed(Ws) 1 1 None MUL.SU Wb,Ws,Wnd {Wnd + 1, Wnd} = signed(Wb) * unsigned(Ws) 1 1 None MUL.US Wb,Ws,Wnd {Wnd + 1, Wnd} = unsigned(Wb) * signed(Ws) 1 1 None MUL.UU Wb,Ws,Wnd {Wnd + 1, Wnd} = unsigned(Wb) * unsigned(Ws) 1 1 None MUL.SU Wb,#lit5,Wnd {Wnd + 1, Wnd} = signed(Wb) * unsigned(lit5) 1 1 None MUL.UU Wb,#lit5,Wnd {Wnd + 1, Wnd} = unsigned(Wb) * unsigned(lit5) 1 1 None MUL f W3:W2 = f * WREG 1 1 None NEG Acc Negate Accumulator 1 1 OA,OB,OAB, SA,SB,SAB C,DC,N,OV,Z 52 53 54 NEG NOP POP NEG f f=f+1 1 1 NEG f,WREG WREG = f + 1 1 1 C,DC,N,OV,Z NEG Ws,Wd Wd = Ws + 1 1 1 C,DC,N,OV,Z NOP No Operation 1 1 None NOPR No Operation 1 1 None POP f Pop f from Top-of-Stack (TOS) 1 1 None POP Wdo Pop from Top-of-Stack (TOS) to Wdo 1 1 None POP.D Wnd Pop from Top-of-Stack (TOS) to W(nd):W(nd + 1) 1 2 None Pop Shadow Registers 1 1 All f Push f to Top-of-Stack (TOS) 1 1 None PUSH Wso Push Wso to Top-of-Stack (TOS) 1 1 None PUSH.D Wns Push W(ns):W(ns + 1) to Top-of-Stack (TOS) 1 2 None POP.S 55 PUSH PUSH Push Shadow Registers 1 1 None Go into Sleep or Idle mode 1 1 WDTO,Sleep Expr Relative Call 1 2 None Wn Computed Call 1 2 None REPEAT #lit14 Repeat Next Instruction lit14 + 1 times 1 1 None REPEAT Wn Repeat Next Instruction (Wn) + 1 times 1 1 None PUSH.S 56 PWRSAV PWRSAV 57 RCALL RCALL RCALL 58 REPEAT #lit1 59 RESET RESET Software Device Reset 1 1 None 60 RETFIE RETFIE Return from interrupt 1 3 (2) None 61 RETLW RETLW Return with Literal in Wn 1 3 (2) None 62 RETURN RETURN Return from Subroutine 1 3 (2) None 63 RLC RLC f f = Rotate Left through Carry f 1 1 C,N,Z RLC f,WREG WREG = Rotate Left through Carry f 1 1 C,N,Z RLC Ws,Wd Wd = Rotate Left through Carry Ws 1 1 C,N,Z RLNC f f = Rotate Left (No Carry) f 1 1 N,Z RLNC f,WREG WREG = Rotate Left (No Carry) f 1 1 N,Z RLNC Ws,Wd Wd = Rotate Left (No Carry) Ws 1 1 N,Z RRC f f = Rotate Right through Carry f 1 1 C,N,Z RRC f,WREG WREG = Rotate Right through Carry f 1 1 C,N,Z RRC Ws,Wd Wd = Rotate Right through Carry Ws 1 1 C,N,Z 64 65 RLNC RRC #lit10,Wn (c) 2008-2012 Microchip Technology Inc. DS70318F-page 279 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 22-2: Base Instr # 66 67 INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Mnemonic RRNC SAC Assembly Syntax # of # of Words Cycles Description Status Flags Affected RRNC f f = Rotate Right (No Carry) f 1 1 RRNC f,WREG WREG = Rotate Right (No Carry) f 1 1 N,Z N,Z RRNC Ws,Wd Wd = Rotate Right (No Carry) Ws 1 1 N,Z SAC Acc,#Slit4,Wdo Store Accumulator 1 1 None SAC.R Acc,#Slit4,Wdo Store Rounded Accumulator 1 1 None Ws,Wnd Wnd = Sign-Extended Ws 1 1 C,N,Z None 68 SE SE 69 SETM SETM f f = 0xFFFF 1 1 SETM WREG WREG = 0xFFFF 1 1 None SETM Ws Ws = 0xFFFF 1 1 None SFTAC Acc,Wn Arithmetic Shift Accumulator by (Wn) 1 1 OA,OB,OAB, SA,SB,SAB SFTAC Acc,#Slit6 Arithmetic Shift Accumulator by Slit6 1 1 OA,OB,OAB, SA,SB,SAB SL f f = Left Shift f 1 1 C,N,OV,Z SL f,WREG WREG = Left Shift f 1 1 C,N,OV,Z SL Ws,Wd Wd = Left Shift Ws 1 1 C,N,OV,Z SL Wb,Wns,Wnd Wnd = Left Shift Wb by Wns 1 1 N,Z SL Wb,#lit5,Wnd Wnd = Left Shift Wb by lit5 1 1 N,Z SUB Acc Subtract Accumulators 1 1 OA,OB,OAB, SA,SB,SAB SUB f f = f - WREG 1 1 C,DC,N,OV,Z SUB f,WREG WREG = f - WREG 1 1 C,DC,N,OV,Z SUB #lit10,Wn Wn = Wn - lit10 1 1 C,DC,N,OV,Z SUB Wb,Ws,Wd Wd = Wb - Ws 1 1 C,DC,N,OV,Z SUB Wb,#lit5,Wd Wd = Wb - lit5 1 1 C,DC,N,OV,Z SUBB f f = f - WREG - (C) 1 1 C,DC,N,OV,Z SUBB f,WREG WREG = f - WREG - (C) 1 1 C,DC,N,OV,Z SUBB #lit10,Wn Wn = Wn - lit10 - (C) 1 1 C,DC,N,OV,Z SUBB Wb,Ws,Wd Wd = Wb - Ws - (C) 1 1 C,DC,N,OV,Z SUBB Wb,#lit5,Wd Wd = Wb - lit5 - (C) 1 1 SUBR f f = WREG - f 1 1 SUBR f,WREG WREG = WREG - f 1 1 C,DC,N,OV,Z SUBR Wb,Ws,Wd Wd = Ws - Wb 1 1 C,DC,N,OV,Z SUBR Wb,#lit5,Wd Wd = lit5 - Wb 1 1 C,DC,N,OV,Z SUBBR f f = WREG - f - (C) 1 1 C,DC,N,OV,Z SUBBR f,WREG WREG = WREG - f - (C) 1 1 C,DC,N,OV,Z SUBBR Wb,Ws,Wd Wd = Ws - Wb - (C) 1 1 C,DC,N,OV,Z C,DC,N,OV,Z 70 71 72 73 74 75 76 SFTAC SL SUB SUBB SUBR SUBBR SWAP C,DC,N,OV,Z C,DC,N,OV,Z SUBBR Wb,#lit5,Wd Wd = lit5 - Wb - (C) 1 1 SWAP.b Wn Wn = Nibble Swap Wn 1 1 None SWAP Wn Wn = Byte Swap Wn 1 1 None 77 TBLRDH TBLRDH Ws,Wd Read Prog<23:16> to Wd<7:0> 1 2 None 78 TBLRDL TBLRDL Ws,Wd Read Prog<15:0> to Wd 1 2 None 79 TBLWTH TBLWTH Ws,Wd Write Ws<7:0> to Prog<23:16> 1 2 None 80 TBLWTL TBLWTL Ws,Wd Write Ws to Prog<15:0> 1 2 None 81 ULNK ULNK Unlink Frame Pointer 1 1 None 82 XOR XOR f f = f .XOR. WREG 1 1 N,Z XOR f,WREG WREG = f .XOR. WREG 1 1 N,Z XOR #lit10,Wn Wd = lit10 .XOR. Wd 1 1 N,Z XOR Wb,Ws,Wd Wd = Wb .XOR. Ws 1 1 N,Z XOR Wb,#lit5,Wd Wd = Wb .XOR. lit5 1 1 N,Z ZE Ws,Wnd Wnd = Zero-Extend Ws 1 1 C,Z,N 83 ZE DS70318F-page 280 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 23.0 DEVELOPMENT SUPPORT (R) (R) The PIC microcontrollers and dsPIC digital signal controllers are supported with a full range of software and hardware development tools: * Integrated Development Environment - MPLAB(R) IDE Software * Compilers/Assemblers/Linkers - MPLAB C Compiler for Various Device Families - HI-TECH C(R) for Various Device Families - MPASMTM Assembler - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB Assembler/Linker/Librarian for Various Device Families * Simulators - MPLAB SIM Software Simulator * Emulators - MPLAB REAL ICETM In-Circuit Emulator * In-Circuit Debuggers - MPLAB ICD 3 - PICkitTM 3 Debug Express * Device Programmers - PICkitTM 2 Programmer - MPLAB PM3 Device Programmer * Low-Cost Demonstration/Development Boards, Evaluation Kits, and Starter Kits 23.1 MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16/32-bit microcontroller market. The MPLAB IDE is a Windows(R) operating system-based application that contains: * A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - In-Circuit Emulator (sold separately) - In-Circuit Debugger (sold separately) * A full-featured editor with color-coded context * A multiple project manager * Customizable data windows with direct edit of contents * High-level source code debugging * Mouse over variable inspection * Drag and drop variables from source to watch windows * Extensive on-line help * Integration of select third party tools, such as IAR C Compilers The MPLAB IDE allows you to: * Edit your source files (either C or assembly) * One-touch compile or assemble, and download to emulator and simulator tools (automatically updates all project information) * Debug using: - Source files (C or assembly) - Mixed C and assembly - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 281 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 23.2 MPLAB C Compilers for Various Device Families The MPLAB C Compiler code development systems are complete ANSI C compilers for Microchip's PIC18, PIC24 and PIC32 families of microcontrollers and the dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 23.3 HI-TECH C for Various Device Families The HI-TECH C Compiler code development systems are complete ANSI C compilers for Microchip's PIC family of microcontrollers and the dsPIC family of digital signal controllers. These compilers provide powerful integration capabilities, omniscient code generation and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple platforms. 23.4 MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for PIC10/12/16/18 MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel(R) standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: 23.5 MPLINK Object Linker/ MPLIB Object Librarian The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: * Efficient linking of single libraries instead of many smaller files * Enhanced code maintainability by grouping related modules together * Flexible creation of libraries with easy module listing, replacement, deletion and extraction 23.6 MPLAB Assembler, Linker and Librarian for Various Device Families MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, PIC32 and dsPIC devices. MPLAB C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: * * * * * * Support for the entire device instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility * Integration into MPLAB IDE projects * User-defined macros to streamline assembly code * Conditional assembly for multi-purpose source files * Directives that allow complete control over the assembly process DS70318F-page 282 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 23.7 MPLAB SIM Software Simulator The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC(R) DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C Compilers, and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. 23.8 MPLAB REAL ICE In-Circuit Emulator System MPLAB REAL ICE In-Circuit Emulator System is Microchip's next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC(R) Flash MCUs and dsPIC(R) Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The emulator is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal (LVDS) interconnection (CAT5). The emulator is field upgradable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables. (c) 2008-2012 Microchip Technology Inc. 23.9 MPLAB ICD 3 In-Circuit Debugger System MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost effective high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices. It debugs and programs PIC(R) Flash microcontrollers and dsPIC(R) DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated Development Environment (IDE). The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with a connector compatible with the MPLAB ICD 2 or MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 supports all MPLAB ICD 2 headers. 23.10 PICkit 3 In-Circuit Debugger/ Programmer and PICkit 3 Debug Express The MPLAB PICkit 3 allows debugging and programming of PIC(R) and dsPIC(R) Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial ProgrammingTM. The PICkit 3 Debug Express include the PICkit 3, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software. DS70318F-page 283 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 23.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express 23.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits The PICkitTM 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip's Flash families of microcontrollers. The full featured Windows(R) programming interface supports baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip's powerful MPLAB Integrated Development Environment (IDE) the PICkitTM 2 enables in-circuit debugging on most PIC(R) microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified. A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. The PICkit 2 Debug Express include the PICkit 2, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software. 23.12 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSPTM cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an MMC card for file storage and data applications. DS70318F-page 284 The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEMTM and dsPICDEMTM demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ(R) security ICs, CAN, IrDA(R), PowerSmart battery management, SEEVAL(R) evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 24.0 ELECTRICAL CHARACTERISTICS This section provides an overview of dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 electrical characteristics. Additional information will be provided in future revisions of this document as it becomes available. Absolute maximum ratings for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 family are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability. Functional operation of the device at these or any other conditions above the parameters indicated in the operation listings of this specification is not implied. Absolute Maximum Ratings(1) Ambient temperature under bias.............................................................................................................-40C to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V Voltage on any pin that is not 5V tolerant, with respect to VSS(3) ................................................... -0.3V to (VDD + 0.3V) Voltage on any 5V tolerant pin with respect to VSS, when VDD 3.0V(3) ................................................. -0.3V to +5.6V Voltage on any 5V tolerant pin with respect to Vss, when VDD < 3.0V(3) ........................................ -0.3V to (VDD + 0.3V) Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin(2) ...........................................................................................................................250 mA Maximum current sourced/sunk by any 4x I/O pin ..................................................................................................15 mA Maximum current sourced/sunk by any 8x I/O pin ..................................................................................................25 mA Maximum current sourced/sunk by any 16x I/O pin ................................................................................................45 mA Maximum current sunk by all ports .......................................................................................................................200 mA Maximum current sourced by all ports(2) ...............................................................................................................200 mA Note 1: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2: Maximum allowable current is a function of device maximum power dissipation (see Table 24-2). 3: See the "Pin Diagrams" section for 5V tolerant pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 285 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 24.1 DC Characteristics TABLE 24-1: OPERATING MIPS VS. VOLTAGE Max MIPS Characteristic VDD Range (in Volts) -- 3.0-3.6V(1) -40C to +85C 40 -- 3.0-3.6V(1) -40C to +125C 40 Note 1: Temp Range (in C) dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer to BO10 in Table 24-11 for BOR values. TABLE 24-2: THERMAL OPERATING CONDITIONS Rating Symbol Min Typ Max Unit Operating Junction Temperature Range TJ -40 -- +125 C Operating Ambient Temperature Range TA -40 -- +85 C Operating Junction Temperature Range TJ -40 -- +140 C Operating Ambient Temperature Range TA -40 -- +125 C Industrial Temperature Devices Extended Temperature Devices Power Dissipation: Internal chip power dissipation: PINT = VDD x (IDD - IOH) PD PINT + PI/O W PDMAX (TJ - TA)/JA W I/O Pin Power Dissipation: I/O = ({VDD - VOH} x IOH) + (VOL x IOL) Maximum Allowed Power Dissipation TABLE 24-3: THERMAL PACKAGING CHARACTERISTICS Characteristic Symbol Typ Max Unit Notes Package Thermal Resistance, 44-Pin QFN JA 28 -- C/W 1 Package Thermal Resistance, 44-Pin TFQP JA 39 -- C/W 1 Package Thermal Resistance, 28-Pin SPDIP JA 42 -- C/W 1 Package Thermal Resistance, 28-Pin SOIC JA 47 -- C/W 1 Package Thermal Resistance, 28-Pin QFN-S JA 34 -- C/W 1 Package Thermal Resistance, 18-Pin SOIC JA 57 -- C/W 1 Package Thermal Resistance, 44-Pin VTLA JA 25 -- C/W 1 Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations. DS70318F-page 286 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-4: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Param Symbol No. Characteristic Min Typ(1) Max Units Conditions Operating Voltage DC10 VDD Supply Voltage(4) 3.0 -- 3.6 V DC12 VDR RAM Data Retention Voltage(2) 1.8 -- -- V -- DC16 VPOR VDD Start Voltage to Ensure Internal Power-on Reset Signal -- -- VSS V -- DC17 SVDD VDD Rise Rate(3) to Ensure Internal Power-on Reset Signal 0.03 -- -- Note 1: 2: 3: Note 1: Industrial and Extended V/ms 0V-3.0V in 0.1 seconds Data in "Typ" column is at 3.3V, +25C unless otherwise stated. This is the limit to which VDD may be lowered without losing RAM data. These parameters are characterized but not tested in manufacturing. Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer to BO10 in Table 24-11 for BOR values. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 287 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Parameter Typical(1) No. Max Units Conditions Operating Current (IDD)(2) DC20d 55 70 mA -40C DC20a 55 70 mA +25C 10 MIPS 3.3V See Note 2 DC20b 55 70 mA +85C DC20c 55 70 mA +125C DC21d 68 85 mA -40C DC21a 68 85 mA +25C 16 MIPS 3.3V See Note 2 and Note 3 DC21b 68 85 mA +85C DC21c 68 85 mA +125C DC22d 78 95 mA -40C DC22a 78 95 mA +25C 20 MIPS 3.3V See Note 2 and Note 3 DC22b 78 95 mA +85C DC22c 78 95 mA +125C DC23d 88 110 mA -40C DC23a 88 110 mA +25C 30 MIPS 3.3V See Note 2 and Note 3 DC23b 88 110 mA +85C DC23c 88 110 mA +125C DC24d 98 120 mA -40C DC24a 98 120 mA +25C 40 MIPS 3.3V See Note 2 DC24b 98 120 mA +85C DC24c 98 120 mA +125C DC25d 128 160 mA -40C 40 MIPS DC25a 125 150 mA +25C See Note 2, except PWM is 3.3V operating at maximum speed DC25b 121 150 mA +85C (PTCON2 = 0x0000) DC25c 119 150 mA +125C DC26d 115 140 mA -40C 40 MIPS DC26a 112 140 mA +25C See Note 2, except PWM is 3.3V operating at 1/2 speed DC26b 110 140 mA +85C (PTCON2 = 0x0001) DC26c 108 140 mA +125C Note 1: Data in "Typical" column is at 3.3V, +25C unless otherwise stated. 2: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: * Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * CPU, SRAM, program memory and data memory are operational * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * CPU executing while(1) statement * JTAG disabled 3: These parameters are characterized but not tested in manufacturing. DS70318F-page 288 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (CONTINUED) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Parameter Typical(1) No. Max Units Conditions Operating Current (IDD)(2) DC27d 111 140 mA -40C 40 MIPS DC27a 108 130 mA +25C See Note 2, except PWM is 3.3V operating at 1/4 speed DC27b 105 130 mA +85C (PTCON2 = 0x0002) DC27c 103 130 mA +125C DC28d 102 130 mA -40C 40 MIPS DC28a 100 120 mA +25C See Note 2, except PWM is 3.3V operating at 1/8 speed DC28b 100 120 mA +85C (PTCON2 = 0x0003) DC28c 100 120 mA +125C Note 1: Data in "Typical" column is at 3.3V, +25C unless otherwise stated. 2: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: * Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * CPU, SRAM, program memory and data memory are operational * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * CPU executing while(1) statement * JTAG disabled 3: These parameters are characterized but not tested in manufacturing. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 289 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-6: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Parameter No. Typical(1) Max Units Conditions Idle Current (IIDLE): Core Off Clock On Base Current(2) DC40d 45 100 mA -40C DC40a 45 100 mA +25C DC40b 45 100 mA +85C DC40c 45 100 mA +125C DC41d 47 100 mA -40C DC41a 47 100 mA +25C DC41b 47 100 mA +85C DC41c 47 100 mA +125C DC42d 50 100 mA -40C DC42a 50 100 mA +25C DC42b 50 100 mA +85C DC42c 50 100 mA +125C DC43d 55 105 mA -40C DC43a 55 105 mA +25C DC43b 55 105 mA +85C DC43c 55 105 mA +125C DC44d 60 105 mA -40C DC44a 60 105 mA +25C DC44b 60 105 mA +85C DC44c 60 105 mA +125C Note 1: 2: 3: 3.3V 10 MIPS 3.3V 16 MIPS(3) 3.3V 20 MIPS(3) 3.3V 30 MIPS(3) 3.3V 40 MIPS Data in "Typical" column is at 3.3V, +25C unless otherwise stated. Base Idle current (IIDLE) is measured as follows: * CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * JTAG disabled These parameters are characterized but not tested in manufacturing. DS70318F-page 290 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-7: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Parameter No. Typical(1) Max Units 500 A Conditions Power-Down Current (IPD)(2,4) DC60d 125 -40C DC60a 135 500 A +25C DC60b 235 500 A +85C DC60c 565 950 A +125C DC61d 40 50 A -40C DC61a 40 50 A +25C DC61b 40 50 A +85C 80 90 A +125C DC61c Note 1: 2: 3: 4: 3.3V Base Power-Down Current 3.3V Watchdog Timer Current: IWDT(3) Data in the Typical column is at 3.3V, +25C unless otherwise stated. IPD (Sleep) current is measured as follows: * CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * All peripheral modules are disabled (PMDx bits are all ones) * The VREGS bit (RCON<8>) = 0 (i.e., core regulator is set to stand-by while the device is in Sleep mode) * JTAG disabled The current is the additional current consumed when the WDT module is enabled. This current should be added to the base IPD current. These currents are measured on the device containing the most memory in this family. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 291 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-8: DC CHARACTERISTICS: DOZE CURRENT (IDOZE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Typical(1) Max Doze Ratio Units DC73a 75 105 1:2 mA DC73f 60 105 1:64 mA DC73g 60 105 1:128 mA DC70a 75 105 1:2 mA DC70f 60 105 1:64 mA DC70g 60 105 1:128 mA DC71a 75 105 1:2 mA DC71f 60 105 1:64 mA DC71g 60 105 1:128 mA Parameter No. DC72a 75 105 1:2 mA DC72f 60 105 1:64 mA 60 105 1:128 mA DC72g Note 1: 2: Conditions -40C 3.3V 40 MIPS +25C 3.3V 40 MIPS +85C 3.3V 40 MIPS +125C 3.3V 40 MIPS Data in the Typical column is at 3.3V, +25C unless otherwise stated. IDOZE is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDOZE measurements are as follows: * Oscillator is configured in EC mode and external clock active, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * CPU, SRAM, program memory and data memory are operational * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * CPU executing while(1) statement * JTAG disabled DS70318F-page 292 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Param Symbol No. VIL Characteristic Min Typ(1) Max Units Conditions Input Low Voltage DI10 I/O Pins VSS -- 0.2 VDD V -- DI15 MCLR VSS -- 0.2 VDD V -- DI16 I/O Pins with OSC1 VSS -- 0.2 VDD V DI18 I/O Pins with SDAx, SCLx VSS -- 0.3 VDD V SMbus disabled I/O Pins with SDAx, SCLx VSS -- 0.8 V SMbus enabled DI19 VIH -- Input High Voltage DI20 DI21 I/O Pins Not 5V Tolerant(4) I/O Pins 5V Tolerant(4) 0.7 VDD 0.7 VDD -- -- VDD 5.5 V V DI28 DI29 SDA1, SCL1 SDA1, SCL1 0.7 VDD 2.1 -- -- 5.5 5.5 V V SMbus disabled SMbus enabled -- 250 -- A VDD = 3.3V, VPIN = VSS -- -- 2 A VSS VPIN VDD, Pin at high-impedance 8x Driver Pins - RC0, RC3-RC8, RC11-RC13 -- -- 4 A VSS VPIN VDD, Pin at high-impedance 16x Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 -- -- 8 A VSS VPIN VDD, Pin at high-impedance ICNPU CNx Pull-up Current IIL Input Leakage Current(2,3,4) DI30 DI50 I/O Pins with: 4x Driver Pins - RA0-RA2, RB0RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 DI55 MCLR -- -- 2 A VSS VPIN VDD DI56 OSC1 -- -- 2 A VSS VPIN VDD, XT and HS modes Note 1: 2: 3: 4: 5: 6: 7: 8: 9: Data in "Typ" column is at 3.3V, +25C unless otherwise stated. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. See "Pin Diagrams" for the list of 5V tolerant I/O pins. VIL source < (VSS - 0.3). Characterized but not tested. Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not tested. Digital 5V tolerant pins cannot tolerate any "positive" input injection current from input sources > 5.5V. Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts. Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted provided the mathematical "absolute instantaneous" sum of the input injection currents from all pins do not exceed the specified limit. Characterized but not tested. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 293 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Param Symbol No. IICL Characteristic DI60c 3: 4: 5: 6: 7: 8: 9: Units Conditions 0 -- -5(5,8) mA All pins except VDD, VSS, AVDD, AVSS, MCLR, VCAP, and RB5 0 -- +5(6,7,8) mA All pins except VDD, VSS, AVDD, AVSS, MCLR, VCAP, RB5, and digital 5V-tolerant designated pins -20(9) -- +20(9) mA Absolute instantaneous sum of all input injection currents from all I/O pins ( | IICL + | IICH | ) IICT Total Input Injection Current (sum of all I/O and control pins) Note 1: 2: Max Input High Injection Current DI60b IICT Typ(1) Input Low Injection Current DI60a IICH Min Data in "Typ" column is at 3.3V, +25C unless otherwise stated. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. See "Pin Diagrams" for the list of 5V tolerant I/O pins. VIL source < (VSS - 0.3). Characterized but not tested. Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not tested. Digital 5V tolerant pins cannot tolerate any "positive" input injection current from input sources > 5.5V. Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts. Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted provided the mathematical "absolute instantaneous" sum of the input injection currents from all pins do not exceed the specified limit. Characterized but not tested. DS70318F-page 294 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Param. Symbol DO10 DO20 VOL VOH Characteristic Min. Typ. Max. Units Conditions Output Low Voltage I/O Pins: 4x Sink Driver Pins - RA0-RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 -- -- 0.4 V IOL 6 mA, VDD = 3.3V See Note 1 Output Low Voltage I/O Pins: 8x Sink Driver Pins - RC0, RC3RC8, RC11-RC13 -- -- 0.4 V IOL 10 mA, VDD = 3.3V See Note 1 Output Low Voltage I/O Pins: 16x Sink Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 -- -- 0.4 V IOL 18 mA, VDD = 3.3V See Note 1 Output High Voltage I/O Pins: 4x Source Driver Pins - RA0RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 2.4 -- -- V IOH -6 mA, VDD = 3.3V See Note 1 Output High Voltage I/O Pins: 8x Source Driver Pins - RC0, RC3-RC8, RC11-RC13 2.4 -- -- V IOH -10 mA, VDD = 3.3V See Note 1 Output High Voltage I/O Pins: 16x Source Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 2.4 -- -- V IOH -18 mA, VDD = 3.3V See Note 1 1.5 -- -- 2.0 -- -- 3.0 -- -- IOH -3 mA, VDD = 3.3V See Note 1 1.5 -- -- IOH -16 mA, VDD = 3.3V See Note 1 2.0 -- -- 3.0 -- -- IOH -4 mA, VDD = 3.3V See Note 1 1.5 -- -- IOH -30 mA, VDD = 3.3V See Note 1 2.0 -- -- 3.0 -- -- Output High Voltage I/O Pins: 4x Source Driver Pins - RA0RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 Output High Voltage 8x Source Driver Pins - RC0, RC3-RC8, RC11-RC13 DO20A VOH1 Output High Voltage I/O Pins: 16x Source Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 Note 1: IOH -12 mA, VDD = 3.3V See Note 1 V V V IOH -11 mA, VDD = 3.3V See Note 1 IOH -12 mA, VDD = 3.3V See Note 1 IOH -25 mA, VDD = 3.3V See Note 1 IOH -8 mA, VDD = 3.3V See Note 1 Parameters are characterized, but not tested. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 295 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-11: ELECTRICAL CHARACTERISTICS: BOR DC CHARACTERISTICS Param No. Symbol Standard Operating Conditions (see Note 3): 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Characteristic Min(1) Typ Max Units 2.55 -- 2.79 V Conditions See Note 2 BO10 VBOR Note 1: 2: 3: Parameters are for design guidance only and are not tested in manufacturing. The device will operate as normal until the VDDMIN threshold is reached. Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. DS70318F-page 296 BOR Event on VDD Transition High-to-Low BOR Event is Tied to VDD Core Voltage Decrease (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-12: DC CHARACTERISTICS: PROGRAM MEMORY Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended DC CHARACTERISTICS Param Symbol No. Characteristic Min Typ(1) Max 10,000 -- -- Units Conditions Program Flash Memory D130 EP Cell Endurance D131 VPR VDD for Read VMIN -- 3.6 V VMIN = Minimum operating voltage D132B VPEW VDD for Self-Timed Write VMIN -- 3.6 V VMIN = Minimum operating voltage D134 TRETD Characteristic Retention 20 -- -- Year Provided no other specifications are violated, -40C to +125C D135 IDDP Supply Current during Programming -- 10 -- mA D136a TRW Row Write Time 1.32 -- 1.74 ms TRW = 11064 FRC cycles, TA = +85C, See Note 2 D136b TRW Row Write Time 1.28 -- 1.79 ms TRW = 11064 FRC cycles, TA = +125C, See Note 2 D137a TPE Page Erase Time 20.1 -- 26.5 ms TPE = 168517 FRC cycles, TA = +85C, See Note 2 D137b TPE Page Erase Time 19.5 -- 27.3 ms TPE = 168517 FRC cycles, TA = +125C, See Note 2 D138a TWW Word Write Cycle Time 42.3 -- 55.9 s TWW = 355 FRC cycles, TA = +85C, See Note 2 D138b TWW Word Write Cycle Time 41.1 -- 57.6 s TWW = 355 FRC cycles, TA = +125C, See Note 2 Note 1: 2: E/W -40C to +125C -- Data in "Typ" column is at 3.3V, +25C unless otherwise stated. Other conditions: FRC = 7.37 MHz, TUN<5:0> = b'011111 (for Min), TUN<5:0> = b'100000 (for Max). This parameter depends on the FRC accuracy (see Table 24-20) and the value of the FRC Oscillator Tuning register (see Register 9-4). For complete details on calculating the Minimum and Maximum time see Section 5.3 "Programming Operations". TABLE 24-13: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS Operating Conditions: Param No. -- Note 1: Symbol CEFC -40C TA +85C for Industrial -40C TA +125C for Extended Characteristics External Filter Capacitor Value(1) Min Typ Max Units 4.7 10 -- F Comments Capacitor must be low series resistance (< 5 ohms) Typical VCAP voltage = 2.5 volts when VDD VDDMIN. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 297 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 24.2 AC Characteristics and Timing Parameters This section defines dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 AC characteristics and timing parameters. TABLE 24-14: TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Operating voltage VDD range as described in Table 24-1. AC CHARACTERISTICS FIGURE 24-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 - for all pins except OSC2 Load Condition 2 - for OSC2 VDD/2 CL Pin RL VSS CL Pin RL = 464 CL = 50 pF for all pins except OSC2 15 pF for OSC2 output VSS TABLE 24-15: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS Param Symbol No. Characteristic Min Typ Max Units Conditions DO50 COSCO OSC2 Pin -- -- 15 pF In XT and HS modes when external clock is used to drive OSC1 DO56 CIO All I/O Pins and OSC2 -- -- 50 pF EC mode DO58 CB SCLx, SDAx -- -- 400 pF In I2CTM mode DS70318F-page 298 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-2: EXTERNAL CLOCK TIMING Q1 Q2 Q3 Q4 Q1 Q2 OS30 OS30 Q3 Q4 OSC1 OS20 OS31 OS31 OS25 CLKO OS41 OS40 TABLE 24-16: EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. OS10 Symb FIN Min Typ(1) Max Units External CLKI Frequency (External clocks allowed only in EC and ECPLL modes) DC -- 40 MHz EC Oscillator Crystal Frequency 3.5 10 -- -- 10 40 MHz MHz XT HS Characteristic Conditions OS20 TOSC TOSC = 1/FOSC 12.5 -- DC ns -- OS25 TCY Instruction Cycle Time(2) 25 -- DC ns -- OS30 TosL, TosH External Clock in (OSC1) High or Low Time 0.375 x TOSC -- 0.625 x TOSC ns EC OS31 TosR, TosF External Clock in (OSC1) Rise or Fall Time -- -- 20 ns EC OS40 TckR CLKO Rise Time(3) -- 5.2 -- ns -- 5.2 -- ns 14 16 18 mA/V Time(3) OS41 TckF CLKO Fall OS42 GM External Oscillator Transconductance(4) Note 1: 2: 3: 4: -- -- VDD = 3.3V TA = +25C Data in "Typ" column is at 3.3V, +25C unless otherwise stated. Instruction cycle period (TCY) equals two times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the "max." cycle time limit is "DC" (no clock) for all devices. Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin. Data for this parameter is Preliminary. This parameter is characterized, but not tested in manufacturing. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 299 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-17: PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V) AC CHARACTERISTICS Param No. Symbol Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Characteristic Min Typ(1) Max Units OS50 FPLLI PLL Voltage Controlled Oscillator (VCO) Input Frequency Range 0.8 -- 8 MHz OS51 FSYS On-Chip VCO System Frequency 100 -- 200 MHz OS52 TLOCK PLL Start-up Time (Lock Time) 0.9 1.5 3.1 mS OS53 DCLK CLKO Stability (Jitter)(2) -3 0.5 3 % Note 1: 2: Conditions ECPLL, XTPLL modes -- -- Measured over 100 ms period Data in "Typ" column is at 3.3V, +25C unless otherwise stated. Parameters are for design guidance only and are not tested in manufacturing. These parameters are characterized by similarity, but are not tested in manufacturing. This specification is based on clock cycle by clock cycle measurements. To calculate the effective jitter for individual time bases or communication clocks use this formula: D CLK Peripheral Clock Jitter = -----------------------------------------------------------------------F OSC ------------------------------------------------------------- Peripheral Bit Rate Clock For example: Fosc = 32 MHz, DCLK = 3%, SPI bit rate clock, (i.e., SCK) is 2 MHz. 3% 3% D CLK SPI SCK Jitter = ------------------------------ = ---------- = -------- = 0.75% 4 16 MHz- 32 ------------------ 2 MHz TABLE 24-18: AUXILIARY PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V) AC CHARACTERISTICS Param No. Symbol Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Characteristic Min Typ(1) Max Units Conditions OS56 FHPOUT 0n-Chip 16x PLL CCO Frequency 112 118 120 MHz -- OS57 FHPIN On-Chip 16x PLL Phase Detector Input Frequency 7.0 7.37 7.5 MHz -- OS58 TSU Frequency Generator Lock Time -- -- 10 s -- Note 1: Data in "Typ" column is at 3.3V, +25C unless otherwise stated. Parameters are for design guidance only and are not tested in manufacturing. DS70318F-page 300 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-19: AC CHARACTERISTICS: INTERNAL FRC ACCURACY AC CHARACTERISTICS Param No. Characteristic Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for Extended Min Typ Max Units Conditions Internal FRC Accuracy @ FRC Frequency = 7.37 MHz(1) F20a FRC -2 -- +2 % -40C TA +85C VDD = 3.0-3.6V F20b FRC -5 -- +5 % -40C TA +125C VDD = 3.0-3.6V Note 1: Frequency calibrated at +25C and 3.3V. TUN bits can be used to compensate for temperature drift. TABLE 24-20: AC CHARACTERISTICS: INTERNAL LPRC ACCURACY AC CHARACTERISTICS Param No. Characteristic Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Min Typ Max Units Conditions LPRC @ 32.768 kHz(1) F21a LPRC -20 6 +20 % -40C TA +85C VDD = 3.0-3.6V F21b LPRC -70 -- +70 % -40C TA +125C VDD = 3.0-3.6V Note 1: Change of LPRC frequency as VDD changes. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 301 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-3: I/O TIMING CHARACTERISTICS I/O Pin (Input) DI35 DI40 I/O Pin (Output) New Value Old Value DO31 DO32 Note: Refer to Figure 24-1 for load conditions. TABLE 24-21: I/O TIMING REQUIREMENTS AC CHARACTERISTICS Param No. Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Min Typ(1) Max Units -- 10 25 ns 8x Source Driver Pins - RC0, RC3RC8, RC11-RC13 -- 8 20 ns 16x Source Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 -- 6 15 ns 4x Source Driver Pins - RA0-RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 -- 10 25 ns 8x Source Driver Pins - RC0, RC3RC8, RC11-RC13 -- 8 20 ns 16x Source Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 -- 6 15 ns TINP INTx Pin High or Low Time (input) 20 -- -- ns -- DI40 TRBP CNx High or Low Time (input) 2 -- -- TCY -- Note 1: Data in "Typ" column is at 3.3V, +25C unless otherwise stated. DO31 Symbol TIOR Characteristic Port Output Rise Time: 4x Source Driver Pins - RA0-RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 DO32 DI35 TIOF DS70318F-page 302 Conditions Refer to Figure 24-1 for test conditions Port Output Fall Time: Refer to Figure 24-1 for test conditions (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-4: VDD RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING CHARACTERISTICS SY12 MCLR SY10 Internal POR SY11 PWRT Time-out OSC Time-out SY30 Internal Reset Watchdog Timer Reset SY13 SY20 SY13 I/O Pins SY35 FSCM Delay Note: Refer to Figure 24-1 for load conditions. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 303 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-22: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param Symbol No. Characteristic(1) Min Typ(2) Max Units Conditions SY10 TMCL MCLR Pulse Width (low) 2 -- -- s -40C to +85C SY11 TPWRT Power-up Timer Period -- 2 4 8 16 32 64 128 -- ms -40C to +85C User programmable SY12 TPOR Power-on Reset Delay 3 10 30 s -40C to +85C SY13 TIOZ I/O High-Impedance from MCLR Low or Watchdog Timer Reset 0.68 0.72 1.2 s -- SY20 TWDT1 Watchdog Timer Time-out Period -- -- -- ms See Section 21.4 "Watchdog Timer (WDT)" and LPRC parameter F21a (Table 24-20). SY30 TOST Oscillator Start-up Time -- 1024 TOSC -- -- TOSC = OSC1 period Note 1: 2: These parameters are characterized but not tested in manufacturing. Data in "Typ" column is at 3.3V, +25C unless otherwise stated. DS70318F-page 304 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-5: TIMER1, 2 AND 3 EXTERNAL CLOCK TIMING CHARACTERISTICS TxCK Tx11 Tx10 Tx15 OS60 Tx20 TMRx Note: Refer to Figure 24-1 for load conditions. TABLE 24-23: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. TA10 TA11 TA15 Symbol TTXH TTXL TTXP Characteristic TxCK High Time TxCK Low Time TxCK Input Period Min. Typ. Max. Units Conditions Synchronous, no prescaler TCY + 20 -- -- ns Synchronous, with prescaler (TCY + 20)/N -- -- ns Asynchronous 20 -- -- ns Must also meet parameter TA15 N = prescale value (1, 8, 64, 256) Synchronous, no prescaler TCY + 20 -- -- ns Synchronous, with prescaler (TCY + 20)/N -- -- ns Asynchronous 20 -- -- ns Synchronous, no prescaler 2 TCY + 40 -- -- ns -- Synchronous, with prescaler Greater of: 40 ns or (2 TCY + 40)/N -- -- -- N = prescale value (1, 8, 64, 256) Asynchronous 40 -- -- ns -- DC -- 50 kHz -- 1.75 TCY + 40 -- -- OS60 FT1 TA20 TCKEXTMRL Delay from External TxCK Clock Edge to Timer Increment Note 1: T1CK Oscillator Input Frequency Range (oscillator enabled by setting bit, TCS (T1CON<1>)) 0.75 TCY + 40 Must also meet parameter TA15 N = prescale value (1, 8, 64, 256) Timer1 is a Type A timer. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 305 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-24: TIMER2 EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic Min. Typ. Max. Units Conditions TB10 TTXH TxCK High Synchronous Time Greater of: 20 ns or (TCY + 20)/N -- -- ns Must also meet parameter TB15 N = prescale value (1, 8, 64, 256) TB11 TTXL TxCK Low Time Greater of: 20 ns or (TCY + 20)/N -- -- ns Must also meet parameter TB15 N = prescale value (1, 8, 64, 256) TB15 TTXP TxCK Input Synchronous Period Greater of: 40 ns or (2 TCY + 40)/N -- -- ns N = prescale value (1, 8, 64, 256) TB20 TCKEXTMRL Delay from External TxCK Clock Edge to Timer Increment 0.75 TCY + 40 -- 1.75 TCY + 40 ns Synchronous -- TABLE 24-25: TIMER3 EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic Min Typ Max Units Conditions TC10 TTXH TxCK High Time Synchronous TCY + 20 -- -- ns Must also meet parameter TC15 TC11 TTXL TxCK Low Time Synchronous TCY + 20 -- -- ns Must also meet parameter TC15 TC15 TTXP TxCK Input Period Synchronous, with prescaler 2 TCY + 40 -- -- ns -- TC20 TCKEXTMRL Delay from External TxCK Clock Edge to Timer Increment 0.75 TCY + 40 -- 1.75 TCY + 40 -- -- DS70318F-page 306 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-6: INPUT CAPTURE (CAPx) TIMING CHARACTERISTICS ICx IC10 IC11 IC15 Note: Refer to Figure 24-1 for load conditions. TABLE 24-26: INPUT CAPTURE TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol IC10 TccL Characteristic(1) ICx Input Low Time Min No prescaler TccH ICx Input High Time No prescaler Note 1: TccP ICx Input Period Conditions -- -- ns 10 -- ns 0.5 TCY + 20 -- ns 10 -- ns (TCY + 40)/N -- ns With prescaler IC15 Units 0.5 TCY + 20 With prescaler IC11 Max -- N = prescale value (1, 4, 16) These parameters are characterized but not tested in manufacturing. FIGURE 24-7: OUTPUT COMPARE MODULE (OCx) TIMING CHARACTERISTICS OCx (Output Compare or PWM Mode) OC10 OC11 Note: Refer to Figure 24-1 for load conditions. TABLE 24-27: OUTPUT COMPARE MODULE TIMING REQUIREMENTS AC CHARACTERISTICS Param Symbol No. Characteristic(1) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended Min Typ Max Units Conditions OC10 TccF OCx Output Fall Time -- -- -- ns See parameter DO32 OC11 TccR OCx Output Rise Time -- -- -- ns See parameter DO31 Note 1: These parameters are characterized but not tested in manufacturing. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 307 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-8: OC/PWM MODULE TIMING CHARACTERISTICS OC20 OCFA OC15 Active OCx Tri-state TABLE 24-28: SIMPLE OC/PWM MODE TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ Max Units Conditions OC15 TFD Fault Input to PWM I/O Change -- -- TCY + 20 ns -- OC20 TFLT Fault Input Pulse Width TCY + 20 -- -- ns -- Note 1: These parameters are characterized but not tested in manufacturing. DS70318F-page 308 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-9: HIGH-SPEED PWM MODULE FAULT TIMING CHARACTERISTICS MP30 FLTx MP20 PWMx FIGURE 24-10: HIGH-SPEED PWM MODULE TIMING CHARACTERISTICS MP11 MP10 PWMx Note: Refer to Figure 24-1 for load conditions. TABLE 24-29: HIGH-SPEED PWM MODULE TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ Max Units Conditions -- 2.5 -- ns -- MP10 TFPWM PWM Output Fall Time MP11 TRPWM PWM Output Rise Time -- 2.5 -- ns -- TFD Fault Input to PWM I/O Change -- -- 15 ns -- TFH Minimum PWM Fault Pulse Width 8 -- -- ns DTC<10> = 10 MP31 TPDLY Tap Delay 1.04 -- -- ns MP32 ACLK PWM Input Clock -- -- 120 MHz MP20 MP30 Note 1: 2: ACLK = 120 MHz See Note 2 These parameters are characterized but not tested in manufacturing. This parameter is a maximum allowed input clock for the PWM module. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 309 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-30: SPIx MAXIMUM DATA/CLOCK RATE SUMMARY Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Maximum Data Rate Master Transmit Only (Half-Duplex) Master Transmit/Receive (Full-Duplex) Slave Transmit/Receive (Full-Duplex) CKE CKP SMP 15 Mhz Table 24-31 -- -- 0,1 0,1 0,1 9 Mhz -- Table 24-32 -- 1 0,1 1 9 Mhz -- Table 24-33 -- 0 0,1 1 15 Mhz -- -- Table 24-34 1 0 0 11 Mhz -- -- Table 24-35 1 1 0 15 Mhz -- -- Table 24-36 0 1 0 11 Mhz -- -- Table 24-37 0 0 0 FIGURE 24-11: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 0) TIMING CHARACTERISTICS SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 Bit 14 - - - - - -1 MSb SDOx SP30, SP31 LSb SP30, SP31 Note: Refer to Figure 24-1 for load conditions. FIGURE 24-12: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY CKE = 1) TIMING CHARACTERISTICS SP36 SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 SDOx MSb Bit 14 - - - - - -1 LSb SP30, SP31 Note: Refer to Figure 24-1 for load conditions. DS70318F-page 310 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-31: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions See Note 3 SP10 TscP Maximum SCK Frequency -- -- 15 MHz SP20 TscF SCKx Output Fall Time -- -- -- ns See parameter DO32 and Note 4 SP21 TscR SCKx Output Rise Time -- -- -- ns See parameter DO31 and Note 4 SP30 TdoF SDOx Data Output Fall Time -- -- -- ns See parameter DO32 and Note 4 SP31 TdoR SDOx Data Output Rise Time -- -- -- ns See parameter DO31 and Note 4 SP35 TscH2doV, TscL2doV SDOx Data Output Valid after SCKx Edge -- 6 20 ns -- SP36 TdiV2scH, TdiV2scL SDOx Data Output Setup to First SCKx Edge 30 -- -- ns -- Note 1: 2: 3: 4: These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not violate this specification. Assumes 50 pF load on all SPIx pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 311 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-13: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = X, SMP = 1) TIMING CHARACTERISTICS SP36 SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 Bit 14 - - - - - -1 MSb SDOx SP30, SP31 SP40 SDIx LSb MSb In LSb In Bit 14 - - - -1 SP41 Note: Refer to Figure 24-1 for load conditions. TABLE 24-32: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions See Note 3 SP10 SP20 TscP TscF Maximum SCK Frequency SCKx Output Fall Time -- -- -- -- 9 -- MHz ns SP21 TscR SCKx Output Rise Time -- -- -- ns SP30 TdoF SDOx Data Output Fall Time -- -- -- ns SP31 TdoR SDOx Data Output Rise Time -- -- -- ns SP35 TscH2doV, SDOx Data Output Valid after -- 6 20 ns TscL2doV SCKx Edge TdoV2sc, SDOx Data Output Setup to 30 -- -- ns -- TdoV2scL First SCKx Edge TdiV2scH, Setup Time of SDIx Data 30 -- -- ns -- TdiV2scL Input to SCKx Edge TscH2diL, Hold Time of SDIx Data Input 30 -- -- ns -- TscL2diL to SCKx Edge These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this specification. Assumes 50 pF load on all SPIx pins. SP36 SP40 SP41 Note 1: 2: 3: 4: DS70318F-page 312 See parameter DO32 and Note 4 See parameter DO31 and Note 4 See parameter DO32 and Note 4 See parameter DO31 and Note 4 -- (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-14: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = X, SMP = 1) TIMING CHARACTERISTICS SCKx (CKP = 0) SP10 SP21 SP20 SP20 SP21 SCKx (CKP = 1) SP35 MSb SDOx Bit 14 - - - - - -1 SP30, SP31 SDIx MSb In LSb SP30, SP31 LSb In Bit 14 - - - -1 SP40 SP41 Note: Refer to Figure 24-1 for load conditions. TABLE 24-33: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions -40C to +125C and see Note 3 See parameter DO32 and Note 4 See parameter DO31 and Note 4 See parameter DO32 and Note 4 See parameter DO31 and Note 4 -- SP10 TscP Maximum SCK Frequency -- -- 9 MHz SP20 TscF SCKx Output Fall Time -- -- -- ns SP21 TscR SCKx Output Rise Time -- -- -- ns SP30 TdoF SDOx Data Output Fall Time -- -- -- ns SP31 TdoR SDOx Data Output Rise Time -- -- -- ns SP35 TscH2doV, SDOx Data Output Valid after -- 6 20 ns TscL2doV SCKx Edge TdoV2scH, SDOx Data Output Setup to 30 -- -- ns -- TdoV2scL First SCKx Edge TdiV2scH, Setup Time of SDIx Data 30 -- -- ns -- TdiV2scL Input to SCKx Edge TscH2diL, Hold Time of SDIx Data Input 30 -- -- ns -- TscL2diL to SCKx Edge These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this specification. Assumes 50 pF load on all SPIx pins. SP36 SP40 SP41 Note 1: 2: 3: 4: (c) 2008-2012 Microchip Technology Inc. DS70318F-page 313 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-15: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING CHARACTERISTICS SP60 SSx SP52 SP50 SCKx (CKP = 0) SP70 SP73 SP72 SP72 SP73 SCKx (CKP = 1) SP35 MSb SDOx Bit 14 - - - - - -1 LSb SP30,SP31 SDIx SDI MSb In Bit 14 - - - -1 SP51 LSb In SP41 SP40 Note: Refer to Figure 24-1 for load conditions. DS70318F-page 314 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-34: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions See Note 3 SP70 SP72 TscP TscF Maximum SCK Input Frequency SCKx Input Fall Time -- -- -- -- 15 -- MHz ns SP73 TscR SCKx Input Rise Time -- -- -- ns SP30 TdoF SDOx Data Output Fall Time -- -- -- ns SP31 TdoR SDOx Data Output Rise Time -- -- -- ns SP35 TscH2doV, TscL2doV TdoV2scH, TdoV2scL TdiV2scH, TdiV2scL SDOx Data Output Valid after SCKx Edge SDOx Data Output Setup to First SCKx Edge Setup Time of SDIx Data Input to SCKx Edge -- 6 20 ns See parameter DO32 and Note 4 See parameter DO31 and Note 4 See parameter DO32 and Note 4 See parameter DO31 and Note 4 -- 30 -- -- ns -- 30 -- -- ns -- SP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP50 TssL2scH, TssL2scL SSx to SCKx or SCKx Input 120 -- -- ns -- SP51 TssH2doZ SSx to SDOx Output High-Impedance(4) 10 -- 50 ns -- SP52 TscH2ssH SSx after SCKx Edge TscL2ssH 1.5 TCY + 40 -- -- ns See Note 4 SP60 TssL2doV SDOx Data Output Valid after -- -- 50 ns -- SSx Edge These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must not violate this specification. Assumes 50 pF load on all SPIx pins. SP36 SP40 Note 1: 2: 3: 4: (c) 2008-2012 Microchip Technology Inc. DS70318F-page 315 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-16: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING CHARACTERISTICS SP60 SSx SP52 SP50 SCKx (CKP = 0) SP70 SP73 SP72 SP72 SP73 SCKx (CKP = 1) SP35 SP52 MSb SDOx Bit 14 - - - - - -1 LSb SP30,SP31 SDIx SDI MSb In Bit 14 - - - -1 SP51 LSb In SP41 SP40 Note: Refer to Figure 24-1 for load conditions. DS70318F-page 316 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-35: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions See Note 3 SP70 TscP Maximum SCK Input Frequency -- -- 11 MHz SP72 TscF SCKx Input Fall Time -- -- -- ns See parameter DO32 and Note 4 SP73 TscR SCKx Input Rise Time -- -- -- ns See parameter DO31 and Note 4 SP30 TdoF SDOx Data Output Fall Time -- -- -- ns See parameter DO32 and Note 4 SP31 TdoR SDOx Data Output Rise Time -- -- -- ns See parameter DO31 and Note 4 SP35 TscH2doV, SDOx Data Output Valid after TscL2doV SCKx Edge -- 6 20 ns -- SP36 TdoV2scH, SDOx Data Output Setup to TdoV2scL First SCKx Edge 30 -- -- ns -- SP40 TdiV2scH, TdiV2scL Setup Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP50 TssL2scH, TssL2scL SSx to SCKx or SCKx Input 120 -- -- ns -- SP51 TssH2doZ SSx to SDOx Output High-Impedance(4) 10 -- 50 ns -- SP52 TscH2ssH SSx after SCKx Edge TscL2ssH 1.5 TCY + 40 -- -- ns See Note 4 SP60 TssL2doV SDOx Data Output Valid after SSx Edge -- -- 50 ns -- Note 1: 2: 3: 4: These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not violate this specification. Assumes 50 pF load on all SPIx pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 317 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-17: SPIx SLAVE MODE (FULL-DUPLEX CKE = 0, CKP = 1, SMP = 0) TIMING CHARACTERISTICS SSX SP52 SP50 SCKX (CKP = 0) SP70 SP73 SP72 SP72 SP73 SCKX (CKP = 1) SP35 MSb SDOX Bit 14 - - - - - -1 LSb SP51 SP30,SP31 SDIX MSb In Bit 14 - - - -1 LSb In SP41 SP40 Note: Refer to Figure 24-1 for load conditions. DS70318F-page 318 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-36: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions See Note 3 SP70 TscP Maximum SCK Input Frequency -- -- 15 MHz SP72 TscF SCKx Input Fall Time -- -- -- ns See parameter DO32 and Note 4 SP73 TscR SCKx Input Rise Time -- -- -- ns See parameter DO31 and Note 4 SP30 TdoF SDOx Data Output Fall Time -- -- -- ns See parameter DO32 and Note 4 SP31 TdoR SDOx Data Output Rise Time -- -- -- ns See parameter DO31 and Note 4 SP35 TscH2doV, SDOx Data Output Valid after TscL2doV SCKx Edge -- 6 20 ns -- SP36 TdoV2scH, SDOx Data Output Setup to TdoV2scL First SCKx Edge 30 -- -- ns -- SP40 TdiV2scH, TdiV2scL Setup Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP50 TssL2scH, TssL2scL SSx to SCKx or SCKx Input 120 -- -- ns -- SP51 TssH2doZ SSx to SDOx Output High-Impedance(4) 10 -- 50 ns -- SP52 TscH2ssH SSx after SCKx Edge TscL2ssH 1.5 TCY + 40 -- -- ns See Note 4 Note 1: 2: 3: 4: These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 66.7 ns. Therefore, the SCK clock generated by the Master must not violate this specification. Assumes 50 pF load on all SPIx pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 319 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-18: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING CHARACTERISTICS SSX SP52 SP50 SCKX (CKP = 0) SP70 SP73 SP72 SP72 SP73 SCKX (CKP = 1) SP35 MSb SDOX Bit 14 - - - - - -1 LSb SP51 SP30,SP31 SDIX MSb In Bit 14 - - - -1 LSb In SP41 SP40 Note: Refer to Figure 24-1 for load conditions. DS70318F-page 320 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-37: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ(2) Max Units Conditions See Note 3 SP70 TscP Maximum SCK Input Frequency -- -- 11 MHz SP72 TscF SCKx Input Fall Time -- -- -- ns See parameter DO32 and Note 4 SP73 TscR SCKx Input Rise Time -- -- -- ns See parameter DO31 and Note 4 SP30 TdoF SDOx Data Output Fall Time -- -- -- ns See parameter DO32 and Note 4 SP31 TdoR SDOx Data Output Rise Time -- -- -- ns See parameter DO31 and Note 4 SP35 TscH2doV, SDOx Data Output Valid after TscL2doV SCKx Edge -- 6 20 ns -- SP36 TdoV2scH, SDOx Data Output Setup to TdoV2scL First SCKx Edge 30 -- -- ns -- SP40 TdiV2scH, TdiV2scL Setup Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 30 -- -- ns -- SP50 TssL2scH, TssL2scL SSx to SCKx or SCKx Input 120 -- -- ns -- SP51 TssH2doZ SSx to SDOx Output High-Impedance(4) 10 -- 50 ns -- SP52 TscH2ssH SSx after SCKx Edge TscL2ssH 1.5 TCY + 40 -- -- ns See Note 4 Note 1: 2: 3: 4: These parameters are characterized, but are not tested in manufacturing. Data in "Typ" column is at 3.3V, 25C unless otherwise stated. The minimum clock period for SCKx is 91 ns. Therefore, the SCK clock generated by the Master must not violate this specification. Assumes 50 pF load on all SPIx pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 321 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-19: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE) SCLx IM31 IM34 IM30 IM33 SDAx Stop Condition Start Condition Note: Refer to Figure 24-1 for load conditions. FIGURE 24-20: I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE) IM20 IM21 IM11 IM10 SCLx IM11 IM26 IM10 IM25 IM33 SDAx In IM40 IM40 IM45 SDAx Out Note: Refer to Figure 24-1 for load conditions. DS70318F-page 322 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-38: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param Symbol No. IM10 IM11 IM20 IM21 Min(1) Max Units TLO:SCL Clock Low Time 100 kHz mode 400 kHz mode 1 MHz mode(2) THI:SCL Clock High Time 100 kHz mode 400 kHz mode 1 MHz mode(2) TF:SCL SDAx and SCLx 100 kHz mode Fall Time 400 kHz mode 1 MHz mode(2) TR:SCL SDAx and SCLx 100 kHz mode Rise Time 400 kHz mode TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) -- 20 + 0.1 CB -- -- 20 + 0.1 CB -- -- -- -- -- -- 300 300 100 1000 s s s s s s ns ns ns ns 1 MHz mode(2) 100 kHz mode 400 kHz mode 1 MHz mode(2) 100 kHz mode 400 kHz mode 1 MHz mode(2) 100 kHz mode 400 kHz mode 1 MHz mode(2) 100 kHz mode 400 kHz mode 1 MHz mode(2) 100 kHz mode 400 kHz mode 1 MHz mode(2) -- 250 100 40 0 0 0.2 TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) TCY/2 (BRG + 1) 300 300 -- -- -- -- 0.9 -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns s s s s s s s s s s s s Characteristic IM25 TSU:DAT Data Input Setup Time IM26 THD:DAT Data Input Hold Time IM30 TSU:STA IM31 THD:STA Start Condition Hold Time IM33 TSU:STO Stop Condition Setup Time IM34 THD:STO Stop Condition Hold Time IM40 IM45 IM50 IM51 Note Start Condition Setup Time Conditions -- -- -- -- -- -- CB is specified to be from 10 pF to 400 pF CB is specified to be from 10 pF to 400 pF -- -- -- -- -- -- Only relevant for Repeated Start condition After this period the first clock pulse is generated -- -- -- 100 kHz mode TCY/2 (BRG + 1) -- ns -- 400 kHz mode TCY/2 (BRG + 1) -- ns -- -- ns -- 1 MHz mode(2) TCY/2 (BRG + 1) TAA:SCL Output Valid 100 kHz mode -- 3500 ns -- From Clock 400 kHz mode -- 1000 ns -- 1 MHz mode(2) -- 400 ns -- TBF:SDA Bus Free Time 100 kHz mode 4.7 -- s Time the bus must be free before a new 400 kHz mode 1.3 -- s transmission can start 1 MHz mode(2) 0.5 -- s Bus Capacitive Loading -- 400 pF -- CB TPGD Pulse Gobbler Delay 65 390 ns See Note 3 1: BRG is the value of the I2CTM Baud Rate Generator. Refer to Section 19. "Inter-Integrated Circuit (I2CTM)" (DS70195) in the "dsPIC33F/PIC24H Family Reference Manual". 2: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only). 3: Typical value for this parameter is 130 ns. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 323 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 FIGURE 24-21: I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE) SCLx IS34 IS31 IS30 IS33 SDAx Stop Condition Start Condition FIGURE 24-22: I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE) IS20 IS21 IS11 IS10 SCLx IS30 IS26 IS31 IS25 IS33 SDAx In IS40 IS40 IS45 SDAx Out DS70318F-page 324 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-39: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param. Symbol IS10 IS11 IS20 IS21 IS25 TLO:SCL THI:SCL TF:SCL TR:SCL TSU:DAT Characteristic Clock Low Time Clock High Time SDAx and SCLx Fall Time SDAx and SCLx Rise Time Data Input Setup Time Min Max Units 100 kHz mode 4.7 -- s Device must operate at a minimum of 1.5 MHz 400 kHz mode 1.3 -- s Device must operate at a minimum of 10 MHz 1 MHz mode(1) 0.5 -- s 100 kHz mode 4.0 -- s Device must operate at a minimum of 1.5 MHz 400 kHz mode 0.6 -- s Device must operate at a minimum of 10 MHz 1 MHz mode(1) 0.5 -- s 100 kHz mode -- 300 ns 400 kHz mode 20 + 0.1 CB 300 ns 1 MHz mode(1) -- 100 ns 100 kHz mode -- 1000 ns IS30 IS31 IS33 IS34 IS40 IS45 IS50 Note 1: THD:DAT Data Input Hold Time TSU:STA Start Condition Setup Time THD:STA Start Condition Hold Time TSU:STO Stop Condition Setup Time THD:STO Stop Condition Hold Time TAA:SCL Output Valid From Clock TBF:SDA Bus Free Time CB -- -- CB is specified to be from 10 pF to 400 pF CB is specified to be from 10 pF to 400 pF 400 kHz mode 20 + 0.1 CB 300 ns 1 MHz mode(1) -- 300 ns 100 kHz mode 250 -- ns -- 400 kHz mode 100 -- ns -- mode(1) 1 MHz IS26 Conditions 100 -- ns -- 100 kHz mode 0 -- s -- 400 kHz mode 0 0.9 s -- 1 MHz mode(1) 0 0.3 s -- 100 kHz mode 4.7 -- s s Only relevant for Repeated Start condition 400 kHz mode 0.6 -- 1 MHz mode(1) 0.25 -- s 100 kHz mode 4.0 -- s After this period, the first clock pulse is generated 400 kHz mode 0.6 -- s 1 MHz mode(1) 0.25 -- s 100 kHz mode 4.7 -- s -- -- 400 kHz mode 0.6 -- s 1 MHz mode(1) 0.6 -- s -- 100 kHz mode 4000 -- ns -- 400 kHz mode 600 -- ns -- 1 MHz mode(1) 250 -- ns -- 100 kHz mode 0 3500 ns -- 400 kHz mode 0 1000 ns -- 1 MHz mode(1) 0 350 ns 100 kHz mode 4.7 -- s 400 kHz mode 1.3 -- s 1 MHz mode(1) 0.5 -- s -- 400 pF Bus Capacitive Loading -- Time the bus must be free before a new transmission can start -- Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 325 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 = TABLE 24-40: 10-BIT HIGH-SPEED ADC MODULE SPECIFICATIONS Standard Operating Conditions (see Note2): 3.0V and 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param Symbol No. Characteristic AD01 AVDD Module VDD Supply AD02 AVSS Module VSS Supply AD10 AD11 AD12 AD13 VINH-VINL VIN IAD -- Full-Scale Input Span Absolute Input Voltage Operating Current Leakage Current Min. Typ. Device Supply -- -- -- -- Analog Input VSS -- AVSS -- -- 8 -- 0.6 Max. Units Conditions -- -- -- -- AVDD is internally connected to VDD. See parameter (DC10) in Table 24-4 AVSS is internally connected to VSS VDD AVDD -- -- V V mA A -- -- -- VINL = AVSS = 0V, AVDD = 3.3V Source Impedance = 100 -- Recommended Impedance -- -- 100 Of Analog Voltage Source DC Accuracy @ 1.5 MSPS AD20A Nr Resolution 10 data bits -- AD21A INL Integral Nonlinearity -0.5 -0.3/+0.5 +1.2 LSb -- AD22A DNL Differential Nonlinearity -0.9 0.6 +0.9 LSb -- Gain Error 13 15 22 LSb -- AD23A GERR Offset Error 6 7 8 LSb -- AD24A EOFF AD25A -- Monotonicity(1) -- -- -- -- Guaranteed DC Accuracy @ 1.7 MSPS AD20B Nr Resolution 10 data bits -- AD21B INL Integral Nonlinearity -0.5 -0.4/+1.1 +1.8 LSb -- AD22B DNL Differential Nonlinearity -1.0 1.0 +1.5 LSb -- Gain Error 13 15 22 LSb -- AD23B GERR AD24B EOFF Offset Error 6 7 8 LSb -- -- -- -- -- Guaranteed AD25B -- Monotonicity(1) DC Accuracy @ 2.0 MSPS AD20C Nr Resolution 10 data bits -- AD21C INL Integral Nonlinearity -0.8 -0.5/+1.8 +2.8 LSb -- AD22C DNL Differential Nonlinearity -1.0 -1.0/+1.8 +2.8 LSb -- Gain Error 14 16 23 LSb -- AD23C GERR Offset Error 6 7 8 LSb -- AD24C EOFF -- -- -- -- Guaranteed AD25C -- Monotonicity(1) Dynamic Performance AD30 THD Total Harmonic Distortion -- -73 -- dB -- AD31 SINAD Signal to Noise and Distortion -- 58 -- dB -- AD32 SFDR Spurious Free Dynamic Range -- -73 -- dB -- Input Signal Bandwidth -- -- 1 MHz -- AD33 FNYQ AD34 ENOB Effective Number of Bits -- 9.4 -- bits -- Note 1: The analog-to-digital conversion result never decreases with an increase in input voltage, and has no missing codes. 2: Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is tested but not characterized. AD17 RIN DS70318F-page 326 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-41: 10-BIT HIGH-SPEED ADC MODULE TIMING REQUIREMENTS Standard Operating Conditions (see Note 2): 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial -40C TA +125C for Extended AC CHARACTERISTICS Param Symbol No. Characteristic Min. Typ(1) Max. Units Conditions -- ns -- Clock Parameters AD50b TAD ADC Clock Period AD55b tCONV Conversion Time AD56b FCNV Throughput Rate 35.8 -- Conversion Rate Devices with Single SAR Devices with Dual SARs -- 14 TAD -- -- -- -- -- 2.0 Msps -- -- -- 4.0 Msps -- 10 s -- Timing Parameters AD63b tDPU Note 1: 2: Time to Stabilize Analog Stage from ADC Off to ADC On(1) 1.0 -- These parameters are characterized but not tested in manufacturing. Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is tested but not characterized. FIGURE 24-23: ANALOG-TO-DIGITAL CONVERSION TIMING PER INPUT Tconv Trigger Pulse TAD ADC Clock ADC Data ADBUFxx 9 Old Data 8 2 1 0 New Data CONV (c) 2008-2012 Microchip Technology Inc. DS70318F-page 327 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-42: COMPARATOR MODULE SPECIFICATIONS DC CHARACTERISTICS Standard Operating Conditions (see Note 2): 3.0V to 3.6V Operating temperature: -40C TA +85C for Industrial -40C TA +125C for Extended Param. Symbol Characteristic No. Min Typ Max Units Comments CM10 VIOFF Input Offset Voltage -58 +14/-40 66 mV -- CM11 VICM Input Common Mode Voltage Range(1) 0 -- AVDD - 1.5 V -- CM12 VGAIN Open Loop Gain(1) 90 -- -- db -- CM13 CMRR Common Mode Rejection Ratio(1) 70 -- -- db -- CM14 TRESP Large Signal Response 21 30 49 ns V+ input step of 100 mv while V- input held at AVDD/2. Delay measured from analog input pin to PWM output pin. Note 1: 2: Parameters are for design guidance only and are not tested in manufacturing. Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is tested but not characterized. TABLE 24-43: DAC MODULE SPECIFICATIONS Standard Operating Conditions (see Note 2): 3.0V to 3.6V Operating temperature: -40C TA +85C for Industrial -40C TA +125C for Extended AC and DC CHARACTERISTICS Param. No. Symbol Characteristic DA01 EXTREF External Voltage Reference(1) Min (1) Typ 0 Max Units Comments AVDD - 1.6 V -- V -- Bits -- DA08 INTREF Internal Voltage Reference DA02 CVRES Resolution DA03 INL Integral Nonlinearity Error -7 -1 +7 LSB DA04 DNL Differential Nonlinearity Error -5 -0.5 +5 LSB DA05 EOFF Offset Error 0.4 -0.8 2.6 % -- DA06 EG Gain Error 0.4 -1.8 5.2 % -- DA07 TSET Settling Time(1) 711 1551 2100 nsec Measured when range = 1 (high range), and CMREF<9:0> transitions from 0x1FF to 0x300. Note 1: 2: 1.25 1.32 1.41 10 AVDD = 3.3V, DACREF = (AVDD/2)V -- Parameters are for design guidance only and are not tested in manufacturing. Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is tested but not characterized. DS70318F-page 328 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 24-44: DAC OUTPUT BUFFER DC SPECIFICATIONS DC CHARACTERISTICS Standard Operating Conditions (see Note 1): 3.0V to 3.6V Operating temperature: -40C TA +85C for Industrial -40C TA +125C for Extended Param. Symbol Characteristic No. Min Typ Max Units Comments DA10 RLOAD Resistive Output Load Impedance 3K -- -- -- DA11 CLOAD Output Load Capacitance -- 20 35 pF -- DA12 IOUT Output Current Drive Strength -1740 1400 +1770 A DA13 VRANGE Full Output Drive Strength Voltage Range AVSS + 250 mV -- AVDD - 900 mV V -- DA14 VLRANGE Output Drive Voltage Range at Reduced Current Drive of 50 A AVSS + 50 mV -- AVDD - 500 mV V -- DA15 IDD Current Consumed when Module is Enabled, High-Power Mode 369 626 948 A Module will always consume this current even if no load is connected to the output DA16 ROUTON Output Impedance when Module is Enabled -- 1200 -- -- Note 1: Sink and source Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is tested but not characterized. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 329 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 330 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 25.0 HIGH TEMPERATURE ELECTRICAL CHARACTERISTICS This section provides an overview of dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 electrical characteristics for devices operating in an ambient temperature range of -40C to +150C. Note: Programming of the Flash memory is not allowed above 125C. The specifications between -40C to +150C are identical to those shown in Section 24.0 "Electrical Characteristics" for operation between -40C to +125C, with the exception of the parameters listed in this section. Parameters in this section begin with an H, which denotes High temperature. For example, parameter DC10 in Section 24.0 "Electrical Characteristics" is the Industrial and Extended temperature equivalent of HDC10. Absolute maximum ratings for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 high temperature devices are listed below. Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional operation of the device at these or any other conditions above the parameters indicated in the operation listings of this specification is not implied. Absolute Maximum Ratings(1) Ambient temperature under bias(3) .........................................................................................................-40C to +150C Storage temperature .............................................................................................................................. -65C to +160C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V Voltage on any pin that is not 5V tolerant with respect to VSS(4) .................................................... -0.3V to (VDD + 0.3V) Voltage on any 5V tolerant pin with respect to VSS when VDD < 3.0V(4) ....................................... -0.3V to (VDD + 0.3V) Voltage on any 5V tolerant pin with respect to VSS when VDD 3.0V(4) .................................................... -0.3V to 5.6V Maximum current out of VSS pin .............................................................................................................................60 mA Maximum current into VDD pin(2) .............................................................................................................................60 mA Maximum junction temperature............................................................................................................................. +155C Maximum current sourced/sunk by any 4x I/O pin ....................................................................................................4 mA Maximum current sourced/sunk by any 8x I/O pin ....................................................................................................8 mA Maximum current sourced/sunk by any 16x I/O pin ................................................................................................16 mA Maximum current sunk by all ports combined ......................................................................................................180 mA Maximum current sourced by all ports combined(2) ..............................................................................................180 mA Note 1: Stresses above those listed under "Absolute Maximum Ratings" can cause permanent damage to the device. This is a stress rating only, and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods can affect device reliability. 2: Maximum allowable current is a function of device maximum power dissipation (see Table 25-2). 3: AEC-Q100 reliability testing for devices intended to operate at 150C is 1,000 hours. Any design in which the total operating time from 125C to 150C will be greater than 1,000 hours is not warranted without prior written approval from Microchip Technology Inc. 4: Refer to the "Pin Diagrams" section for 5V tolerant pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 331 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 25.1 High Temperature DC Characteristics TABLE 25-1: OPERATING MIPS VS. VOLTAGE Max MIPS Characteristic VDD Range (in Volts) Temperature Range (in C) -- 3.0V to 3.6V(1) -40C to +150C Note 1: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 20 Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer to BO10 in Table 24-11 for BOR values. TABLE 25-2: THERMAL OPERATING CONDITIONS Rating Symbol Min Typ Max Unit Operating Junction Temperature Range TJ -40 -- +155 C Operating Ambient Temperature Range TA -40 -- +150 C High Temperature Devices Power Dissipation: Internal chip power dissipation: PINT = VDD x (IDD - IOH) PD PINT + PI/O W PDMAX (TJ - TA)/JA W I/O Pin Power Dissipation: I/O = ({VDD - VOH} x IOH) + (VOL x IOL) Maximum Allowed Power Dissipation TABLE 25-3: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +150C for High Temperature DC CHARACTERISTICS Parameter No. Symbol Characteristic Min Typ Max Units 3.0 3.3 3.6 V Conditions Operating Voltage HDC10 Supply Voltage VDD DS70318F-page 332 -- -40C to +150C (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 25-4: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +150C for High Temperature DC CHARACTERISTICS Parameter No. Typical(1) Max Units Conditions Power-Down Current (IPD)(2,4) HDC60e 1000 2000 A +150C 3.3V Base Power-Down Current HDC61c 100 110 A +150C 3.3V Watchdog Timer Current: IWDT(3) Note 1: 2: 3: 4: Data in the Typical column is at 3.3V, +25C unless otherwise stated. IPD (Sleep) current is measured as follows: * CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * All peripheral modules are disabled (PMDx bits are all ones) * The VREGS bit (RCON<8>) = 0 (i.e., core regulator is set to stand-by while the device is in Sleep mode) * JTAG disabled The current is the additional current consumed when the WDT module is enabled. This current should be added to the base IPD current. These currents are measured on the device containing the most memory in this family. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 333 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 25-5: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +150C for High Temperature DC CHARACTERISTICS Param. Symbol DO10 DO20 VOL VOH Characteristic Min. Typ. Max. Units Conditions Output Low Voltage I/O Pins: 4x Sink Driver Pins - RA0-RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 -- -- 0.4 V IOL 3.6 mA, VDD = 3.3V See Note 1 Output Low Voltage I/O Pins: 8x Sink Driver Pins - RC0, RC3RC8, RC11-RC13 -- -- 0.4 V IOL 6 mA, VDD = 3.3V See Note 1 Output Low Voltage I/O Pins: 16x Sink Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 -- -- 0.4 V IOL 12 mA, VDD = 3.3V See Note 1 Output High Voltage I/O Pins: 4x Source Driver Pins - RA0RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 2.4 -- -- V IOL -4 mA, VDD = 3.3V See Note 1 Output High Voltage I/O Pins: 8x Source Driver Pins - RC0, RC3-RC8, RC11-RC13 2.4 -- -- V IOL -8 mA, VDD = 3.3V See Note 1 Output High Voltage I/O Pins: 16x Source Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 2.4 -- -- V IOL -16 mA, VDD = 3.3V See Note 1 1.5 -- -- 2.0 -- -- 3.0 -- -- IOH -2 mA, VDD = 3.3V See Note 1 1.5 -- -- IOH -7.5 mA, VDD = 3.3V See Note 1 2.0 -- -- 3.0 -- -- IOH -3 mA, VDD = 3.3V See Note 1 1.5 -- -- IOH -15 mA, VDD = 3.3V See Note 1 2.0 -- -- 3.0 -- -- Output High Voltage I/O Pins: 4x Source Driver Pins - RA0RA2, RB0-RB2, RB5-RB10, RB15, RC1, RC2, RC9, RC10 Output High Voltage 8x Source Driver Pins - RC0, RC3-RC8, RC11-RC13 DO20A VOH1 Output High Voltage I/O Pins: 16x Source Driver Pins - RA3, RA4, RB3, RB4, RB11-RB14 Note 1: IOH -3.9 mA, VDD = 3.3V See Note 1 V V V IOH -3.7 mA, VDD = 3.3V See Note 1 IOH -6.8 mA, VDD = 3.3V See Note 1 IOH -14 mA, VDD = 3.3V See Note 1 IOH -7 mA, VDD = 3.3V See Note 1 Parameters are characterized, but not tested. DS70318F-page 334 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 25-6: DC CHARACTERISTICS: PROGRAM MEMORY DC CHARACTERISTICS Param Symbol No. Characteristic(1) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +150C for High Temperature Min Typ Max Units Conditions 10,000 -- -- E/W -40C to +150C(2) 20 -- -- Year 1000 E/W cycles or less and no other specifications are violated Program Flash Memory HD130 EP Cell Endurance HD134 TRETD Characteristic Retention Note 1: 2: These parameters are assured by design, but are not characterized or tested in manufacturing. Programming of the Flash memory is not allowed above 125C. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 335 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 25.2 AC Characteristics and Timing Parameters The information contained in this section defines dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/ X04 AC characteristics and timing parameters for high temperature devices. However, all AC timing specifications in this section are the same as those in Section 31.2 "AC Characteristics and Timing Parameters", with the exception of the parameters listed in this section. Parameters in this section begin with an H, which denotes High temperature. For example, parameter OS53 in Section 31.2 "AC Characteristics and Timing Parameters" is the Industrial and Extended temperature equivalent of HOS53. TABLE 25-7: TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC AC CHARACTERISTICS FIGURE 25-1: Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +150C for High Temperature Operating voltage VDD range as described in Table 25-1. LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 - for all pins except OSC2 Load Condition 2 - for OSC2 VDD/2 CL Pin RL VSS CL Pin RL = 464 CL = 50 pF for all pins except OSC2 15 pF for OSC2 output VSS TABLE 25-8: PLL CLOCK TIMING SPECIFICATIONS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40C TA +150C for High Temperature Param No. Symbol Characteristic CLKO Stability (Jitter)(1) Min Typ Max Units -5 0.5 5 % HOS53 DCLK Note 1: These parameters are characterized, but are not tested in manufacturing. DS70318F-page 336 Conditions Measured over 100 ms period (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 25-9: SPIx MASTER MODE (CKE = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40C TA +150C for High Temperature Param No. Symbol Characteristic(1) Min Typ Max Units Conditions HSP35 TscH2doV, SDOx Data Output Valid after TscL2doV SCKx Edge -- 10 25 ns -- HSP40 TdiV2scH, Setup Time of SDIx Data Input TdiV2scL to SCKx Edge 28 -- -- ns -- HSP41 TscH2diL, TscL2diL 35 -- -- ns -- Note 1: These parameters are characterized but not tested in manufacturing. Hold Time of SDIx Data Input to SCKx Edge TABLE 25-10: SPIx MODULE MASTER MODE (CKE = 1) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40C TA +150C for High Temperature Param No. Symbol Characteristic(1) Min Typ Max Units Conditions HSP35 TscH2doV, SDOx Data Output Valid after TscL2doV SCKx Edge -- 10 25 ns -- HSP36 TdoV2sc, TdoV2scL 35 -- -- ns -- HSP40 TdiV2scH, Setup Time of SDIx Data Input TdiV2scL to SCKx Edge 28 -- -- ns -- HSP41 TscH2diL, TscL2diL 35 -- -- ns -- Note 1: SDOx Data Output Setup to First SCKx Edge Hold Time of SDIx Data Input to SCKx Edge These parameters are characterized but not tested in manufacturing. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 337 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 25-11: SPIx MODULE SLAVE MODE (CKE = 0) TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40C TA +150C for High Temperature Param No. Symbol Characteristic(1) Min Typ Max Units Conditions HSP35 TscH2doV, TscL2doV SDOx Data Output Valid after SCKx Edge -- -- 35 ns -- HSP40 TdiV2scH, TdiV2scL Setup Time of SDIx Data Input to SCKx Edge 25 -- -- ns -- HSP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 25 -- -- ns -- HSP51 TssH2doZ SSx to SDOx Output High-Impedance 15 -- 55 ns Note 1: 2: See Note 2 These parameters are characterized but not tested in manufacturing. Assumes 50 pF load on all SPIx pins. TABLE 25-12: SPIx MODULE SLAVE MODE (CKE = 1) TIMING REQUIREMENTS AC CHARACTERISTICS Param No. Symbol Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +150C for High Temperature Characteristic(1) Min Typ Max Units Conditions HSP35 TscH2doV, SDOx Data Output Valid after TscL2doV SCKx Edge -- -- 35 ns -- HSP40 TdiV2scH, Setup Time of SDIx Data Input TdiV2scL to SCKx Edge 25 -- -- ns -- HSP41 TscH2diL, TscL2diL Hold Time of SDIx Data Input to SCKx Edge 25 -- -- ns -- HSP51 TssH2doZ SSx to SDOX Output High-Impedance 15 -- 55 ns HSP60 TssL2doV SDOx Data Output Valid after SSx Edge -- -- 55 ns Note 1: 2: These parameters are characterized but not tested in manufacturing. Assumes 50 pF load on all SPIx pins. DS70318F-page 338 See Note 2 -- (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 26.0 50 MIPS ELECTRICAL CHARACTERISTICS This section provides an overview of dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 electrical characteristics for devices operating at 50 MIPS. The specifications for 50 MIPS are identical to those shown in Section 24.0 "Electrical Characteristics", with the exception of the parameters listed in this section. Parameters in this section begin with the letter "M", which denotes 50 MIPS operation. For example, parameter DC29a in Section 24.0 "Electrical Characteristics", is the up to 40 MIPS operation equivalent of MDC29a. Absolute maximum ratings for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 50 MIPS devices are listed below. Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional operation of the device at these or any other conditions above the parameters indicated in the operation listings of this specification is not implied. Absolute Maximum Ratings(1) Ambient temperature under bias.............................................................................................................. .-40C to +85C Storage temperature .............................................................................................................................. -65C to +150C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V Voltage on any pin that is not 5V tolerant, with respect to VSS(3) ................................................... -0.3V to (VDD + 0.3V) Voltage on any 5V tolerant pin with respect to VSS, when Vdd 3.0V(3) ................................................. -0.3V to +5.6V Voltage on any 5V tolerant pin with respect to Vss, when VDD < 3.0V(3) ........................................ -0.3V to (VDD + 0.3V) Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin(2) ...........................................................................................................................250 mA Maximum current sourced/sunk by any 4x I/O pin ..................................................................................................15 mA Maximum current sourced/sunk by any 8x I/O pin ..................................................................................................25 mA Maximum current sourced/sunk by any 16x I/O pin ................................................................................................45 mA Maximum current sunk by all ports .......................................................................................................................200 mA Maximum current sourced by all ports(2) ...............................................................................................................200 mA Note 1: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2: Maximum allowable current is a function of device maximum power dissipation (see Table 24-2). 3: See the "Pin Diagrams" section for 5V tolerant pins. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 339 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 26.1 DC Characteristics TABLE 26-1: OPERATING MIPS VS. VOLTAGE Max MIPS Characteristic VDD Range (in Volts) Temp Range (in C) -- 3.0-3.6V(1) -40C to +85C Note 1: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 50 Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer to BO10 in Table 24-11 for BOR values. TABLE 26-2: DC CHARACTERISTICS: OPERATING CURRENT (IDD) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial DC CHARACTERISTICS Parameter No. Typical Max Units Conditions Operating Current (IDD)(1) MDC29d 105 125 mA -40C 50 MIPS MDC29a 105 125 mA +25C 3.3V See Note 1 MDC29b 105 125 mA +85C Note 1: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements are as follows: * Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * CPU, SRAM, program memory and data memory are operational * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * CPU executing while(1) statement * JTAG disabled DS70318F-page 340 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 26-3: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial DC CHARACTERISTICS Parameter No. Typical Max Units Conditions Idle Current (IIDLE): Core Off Clock On Base Current(1) MDC45d 64 105 mA -40C MDC45a 64 105 mA +25C MDC45b 64 105 mA +85C Note 1: 3.3V 50 MIPS Base Idle current (IIDLE) is measured as follows: * CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * The NVMSIDL bit (NVMCON<12>) = 1 (i.e., Flash regulator is set to stand-by while the device is in Idle mode) * JTAG disabled (c) 2008-2012 Microchip Technology Inc. DS70318F-page 341 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 26-4: DC CHARACTERISTICS: DOZE CURRENT (IDOZE) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial DC CHARACTERISTICS Parameter No. Typical Max Doze Ratio Units MDC74a 80 105 1:2 mA MDC74f 65 105 1:64 mA MDC74g 65 105 1:128 mA MDC75a 81 105 1:2 mA MDC75f 65 105 1:64 mA MDC75g 65 105 1:128 mA MDC76a 81 105 1:2 mA MDC76f 65 105 1:64 mA 65 105 1:128 mA MDC76g Note 1: Conditions -40C 3.3V 50 MIPS +25C 3.3V 50 MIPS +85C 3.3V 50 MIPS primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDOZE measurements are as follows: * Oscillator is configured in EC mode and external clock active, OSC1 is driven with external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required) * CLKO is configured as an I/O input pin in the Configuration word * All I/O pins are configured as inputs and pulled to VSS * MCLR = VDD, WDT and FSCM are disabled * CPU, SRAM, program memory and data memory are operational * No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are zeroed) * CPU executing while(1) statement * JTAG disabled DS70318F-page 342 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 26.2 AC Characteristics and Timing Parameters This section defines dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 AC characteristics and timing parameters for 50 MIPS devices. TABLE 26-5: EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial AC CHARACTERISTICS Param No. MOS10 MOS20 MOS25 Note 1: 2: Symb FIN TOSC TCY Min Typ(1) Max Units External CLKI Frequency (External clocks allowed only in EC and ECPLL modes) DC -- 50 MHz EC Oscillator Crystal Frequency 3.5 10 -- -- 10 50 MHz MHz XT HS TOSC = 1/FOSC 10 -- DC ns -- 20 -- DC ns -- Characteristic Instruction Cycle Time(2) Conditions Data in "Typ" column is at 3.3V, +25C unless otherwise stated. Instruction cycle period (TCY) equals two times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the "max." cycle time limit is "DC" (no clock) for all devices. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 343 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 26-6: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1) Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial AC CHARACTERISTICS Param No. MTA10 Symbol TTXH Characteristic Min Typ Max Units Conditions TxCK High Synchronous, Time no prescaler TCY + 15 -- -- ns (TCY + 15)/N -- -- ns Asynchronous 15 -- -- ns Must also meet parameter TA15. N = prescale value (1, 8, 64, 256) Synchronous, no prescaler (TCY + 15) -- -- ns Synchronous, with prescaler (TCY + 10)/N -- -- ns Synchronous, with prescaler MTA11 TTXL TxCK Low Time Asynchronous MTA15 TTXP MOS60 Ft1 MTA20 Note 1: Must also meet parameter TA15. N = prescale value (1, 8, 64, 256) 15 -- -- ns 2 TCY + 30 -- -- ns Synchronous, with prescaler Greater of: 40 ns or (2 TCY + 30)/N -- -- -- Asynchronous 30 -- -- ns -- DC -- 50 kHz -- 0.75 TCY + 30 -- 1.75 TCY + 30 -- -- TxCK Input Synchronous, Period no prescaler SOSCI/T1CK Oscillator Input frequency Range (oscillator enabled by setting bit TCS (T1CON<1>)) TCKEXTMRL Delay from External TxCK Clock Edge to Timer Increment -- N = prescale value (1, 8, 64, 256) Timer1 is a Type A. DS70318F-page 344 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 26-7: TIMER2 EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial AC CHARACTERISTICS Param No. Characteristic(1) Min Typ Max Units Conditions MTB10 TtxH TxCK High Synchronous mode Time Greater of: 15 or (TCY + 15)/N -- -- ns Must also meet parameter TB15 N = prescale value (1, 8, 64, 256) MTB11 TtxL TxCK Low Synchronous Time mode Greater of: 15 or (TCY + 15)/N -- -- ns Must also meet parameter TB15 N = prescale value (1, 8, 64, 256) MTB15 TtxP TxCK Input Period Synchronous mode Greater of: 40 or (2 TCY + 30)/N -- -- ns N = prescale value (1, 8, 64, 256) MTB20 TCKEXTMRL Delay from External TxCK Clock Edge to Timer Increment 0.75 TCY + 30 -- 1.75 TCY + 30 ns Note 1: Symbol These parameters are characterized, but are not tested in manufacturing. TABLE 26-8: TIMER3 EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial AC CHARACTERISTICS Param No. -- Symbol Characteristic(1) Min Typ Max Units Conditions MTC10 TtxH TxCK High Time Synchronous TCY + 10 -- -- ns Must also meet parameter TC15 MTC11 TtxL TxCK Low Time Synchronous TCY + 10 -- -- ns Must also meet parameter TC15 MTC15 TtxP TxCK Input Period Synchronous, with prescaler 2 TCY + 20 -- -- ns -- 0.75 TCY + 20 -- 1.75 TCY + 20 ns -- MTC20 TCKEXTMRL Delay from External TxCK Clock Edge to Timer Increment Note 1: These parameters are characterized, but are not tested in manufacturing. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 345 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE 26-9: SIMPLE OC/PWM MODE TIMING REQUIREMENTS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40C TA +85C for Industrial AC CHARACTERISTICS Param No. Symbol Characteristic(1) Min Typ Max Units Conditions MOC15 TFD Fault Input to PWM I/O Change -- -- TCY + 10 ns -- MOC20 TFLT Fault Input Pulse Width TCY + 10 -- -- ns -- Note 1: These parameters are characterized but not tested in manufacturing. DS70318F-page 346 (c) 2008-2012 Microchip Technology Inc. DC AND AC DEVICE CHARACTERISTICS GRAPHS Note: The graphs provided following this note are a statistical summary based on a limited number of samples and are provided for design guidance purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore, outside the warranted range. FIGURE 27-1: VOH - 4x DRIVER PINS -0.080 -0.030 3.6V -0.070 -0.025 IOH (A) IOH (A) 3V -0.015 Absolute Maximum -0.010 3.3V -0.050 Absolute Maximum -0.040 3V -0.030 -0.020 -0.005 -0.010 0.000 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 FIGURE 27-2: VOH - 8x DRIVER PINS -0.040 3.6V -0.030 3.3V -0.025 Absolute Maximum 3V -0.020 -0.015 DS70318F-page 347 -0.010 -0.005 0.000 0.00 1.00 2.00 VOH (V) 0.000 0.00 1.00 2.00 VOH (V) VOH (V) IOH (A) 3.6V -0.060 3.3V -0.020 -0.035 VOH - 16x DRIVER PINS FIGURE 27-3: 3.00 4.00 3.00 4.00 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. 27.0 FIGURE 27-6: VOL - 4x DRIVER PINS 0.120 0.040 0.035 3.6V 0.030 3.6V 0.100 3.3V 0.025 3.3V 0.080 3V IOL (A) IOL (A) VOL - 16x DRIVER PINS 0.020 0.015 Absolute Maximum 3V 0.060 Absolute Maximum 0.040 0.010 0.020 0.005 0.000 0.00 1.00 2.00 3.00 4.00 VOL (V) FIGURE 27-5: 0.060 3.6V 0.050 3.3V IOL (A) (c) 2008-2012 Microchip Technology Inc. 3V 0.030 Absolute Maximum 0.020 0.010 0.000 0.00 1.00 2.00 VOL (V) 1.00 2.00 VOL (V) VOL - 8x DRIVER PINS 0.040 0.000 0.00 3.00 4.00 3.00 4.00 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 348 FIGURE 27-4: FIGURE 27-9: TYPICAL IPD CURRENT @ VDD = 3.3V 1220 118 108 1020 98 IDO OZE Current (mA) IPD Current (A) TYPICAL IDOZE CURRENT @ VDD = 3.3V 820 620 420 88 78 68 50 MIPS 58 40 MIPS 48 38 220 28 20 -40 25 65 85 125 18 150 1:1 Temperature (Celsius) FIGURE 27-8: 1:2 1:64 1:128 Doze Ratio TYPICAL IDD CURRENT @ VDD = 3.3V FIGURE 27-10: 120 TYPICAL IIDLE CURRENT @ VDD = 3.3V 70 110 65 90 Average (mA) Average (mA) 100 80 70 60 55 50 60 DS70318F-page 349 45 50 40 10 20 30 MIPS 40 50 40 10 20 30 MIPS 40 50 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 (c) 2008-2012 Microchip Technology Inc. FIGURE 27-7: TYPICAL FRC FREQUENCY @ VDD = 3.3V FIGURE 27-13: 7.45 1.36 1.35 7.35 1.34 7.3 INTREF (V) FRC Frequency (MHz) 7.4 7.25 7.2 7.15 1.33 1.32 1.31 7.1 71 1.3 7.05 7 1.29 -40 25 85 125 150 FIGURE 27-12: TYPICAL LPRC FREQUENCY @ VDD = 3.3V 34 32 30 (c) 2008-2012 Microchip Technology Inc. 28 26 24 22 20 18 -40 25 85 Temperature (Celsius) -40 25 85 Temperature (Celsius) Temperature (Celsius) LPRC Frequency (kHz) TYPICAL INTREF @ VDD = 3.3V 125 150 125 150 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 DS70318F-page 350 FIGURE 27-11: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 28.0 PACKAGING INFORMATION 28.1 Package Marking Information 18-Lead SOIC (.300") Example XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX dsPIC33FJ06 GS101-I/SO YYWWNNN 0830235 e3 28-Lead SOIC Example XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX YYWWNNN 28-Lead SPDIP e3 * Note: 0830235 Example XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN Legend: XX...X Y YY WW NNN dsPIC33FJ06GS 202-E/SO e3 dsPIC33FJ06GS 202-E/SP e3 0830235 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. If the full Microchip part number cannot be marked on one line, it is carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 351 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 28.1 Package Marking Information (Continued) 28-Lead QFN-S XXXXXXXX XXXXXXXX YYWWNNN 44-Lead QFN XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN 44-Lead TQFP XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN 33FJ06GS 202EMM e3 0830235 Example dsPIC33FJ16 GS504-E/ML e3 0830235 Example dsPIC33FJ 16GS504 -E/PT e3 0830235 44-Lead VTLA (TLA) Example XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN dsPIC33FJ 16GS504 e3 -E/TL Legend: XX...X Y YY WW NNN e3 * Note: Example 0830235 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. If the full Microchip part number cannot be marked on one line, it is carried over to the next line, thus limiting the number of available characters for customer-specific information. DS70318F-page 352 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 28.2 Package Details /HDG3ODVWLF6PDOO2XWOLQH 62 :LGHPP%RG\>62,&@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 3 e b h h c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c) 2008-2012 Microchip Technology Inc. DS70318F-page 353 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF6PDOO2XWOLQH 62 :LGHPP%RG\>62,&@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 3 e b h A2 A h c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page 354 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG6NLQQ\3ODVWLF'XDO,Q/LQH 63 PLO%RG\>63',3@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ N NOTE 1 E1 1 2 3 D E A2 A L c b1 A1 b e e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c) 2008-2012 Microchip Technology Inc. DS70318F-page 355 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 00 [[PP%RG\>4)16@ ZLWKPP&RQWDFW/HQJWK 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D D2 EXPOSED PAD e E2 E b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page 356 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 00 [[PP%RG\>4)16@ ZLWKPP&RQWDFW/HQJWK 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ (c) 2008-2012 Microchip Technology Inc. DS70318F-page 357 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 0/ [PP%RG\>4)1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D D2 EXPOSED PAD e E E2 b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page 358 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF4XDG)ODW1R/HDG3DFNDJH 0/ [PP%RG\>4)1@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ (c) 2008-2012 Microchip Technology Inc. DS70318F-page 359 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF7KLQ4XDG)ODWSDFN 37 [[PP%RG\PP>74)3@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D D1 E e E1 N b NOTE 1 1 2 3 NOTE 2 A c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page 360 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 /HDG3ODVWLF7KLQ4XDG)ODWSDFN 37 [[PP%RG\PP>74)3@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ (c) 2008-2012 Microchip Technology Inc. DS70318F-page 361 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS70318F-page 362 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2008-2012 Microchip Technology Inc. DS70318F-page 363 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 364 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 APPENDIX A: REVISION HISTORY Revision A (January 2008) This is the initial revision of this document. Revision B (June 2008) This revision includes minor typographical and formatting changes throughout the data sheet text. In addition, redundant information was removed that is now available in the respective chapters of the dsPIC33F/PIC24H Family Reference Manual, which can be obtained from the Microchip website (www.microchip.com). The major changes are referenced by their respective section in the following table. TABLE A-1: MAJOR SECTION UPDATES Section Name Update Description "High-Performance, 16-bit Digital Signal Controllers" Moved location of Note 1 (RPn pin) references (see "Pin Diagrams"). Section 3.0 "Memory Organization" Updated CPU Core Register map SFR reset value for CORCON (see Table 3-1). Removed Interrupt Controller Register Map SFR IPC29 and updated reset values for IPC0, IPC1, IPC14, IPC16, IPC23, IPC24, IPC27, and IPC28 (see Table 3-5). Removed Interrupt Controller Register Map SFR IPC24 and IPC29 and updated reset values for IPC0, IPC1, IPC2, IPC14, IPC16, IPC23, IPC27, and IPC28 (see Table 3-6). Removed Interrupt Controller Register Map SFR IPC24 and updated reset values for IPC1, IPC2, IPC4, IPC14, IPC16, IPC23, IPC24, IPC27, and IPC28 (see Table 3-7). Updated Interrupt Controller Register Map SFR reset values for IPC1, IPC14, IPC16, IPC23, IPC24, IPC27, and IPC28 (see Table 3-8). Updated Interrupt Controller Register Map SFR reset values for IPC1, IPC14, IPC16, IPC23, IPC24, IPC25, IPC26, IPC27, IPC28, and IPC29 (see Table 3-9). Updated Interrupt Controller Register Map SFR reset values for IPC1, IPC4, IPC14, IPC16, IPC23, IPC24, IPC25, IPC26, IPC27, IPC28, and IPC29 (see Table 3-10). Added SFR definitions for RPOR16 and RPOR17 (see Table 3-34, Table 3-35, and Table 3-36). Updated bit definitions for PORTA, PORTB, and PORTC SFRs (ODCA, ODCB, and ODCC) (see Table 3-37, Table 3-38, Table 3-39, and Table 3-40). Updated bit definitions and reset value for System Control Register map SFR CLKDIV (see Table 3-41). Added device-specific information to title of PMD Register Map (see Table 3-47). Added device-specific PMD Register Maps (see Table 3-46, Table 3-45, and Table 3-43). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 365 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-1: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 7.0 "Oscillator Configuration" Update Description Removed the first sentence of the third clock source item (External Clock) in Section 7.1.1 "System Clock sources" Updated the default bit values for DOZE and FRCDIV in the Clock Divisor Register (see Register 7-2). Section 8.0 "Power-Saving Features" Added the following six registers: * "PMD1: Peripheral Module Disable Control Register 1" * "PMD2: Peripheral Module Disable Control Register 2" * "PMD3: Peripheral Module Disable Control Register 3" * "PMD4: Peripheral Module Disable Control Register 4" * "PMD6: Peripheral Module Disable Control Register 6" * "PMD7: Peripheral Module Disable Control Register 7" Section 9.0 "I/O Ports" Added paragraph and Table 9-1 to Section 9.1.1 "Open-Drain Configuration", which provides details on I/O pins and their functionality. Removed 9.1.2 "5V Tolerance". Updated MUX range and removed virtual pin details in Figure 9-2. Updated PWM Input Name descriptions in Table 9-1. Added Section 9.4.2.3 "Virtual Pins". Updated bit values in all Peripheral Pin Select Input Registers (see Register 9-1 through Register 9-14). Updated bit name information for Peripheral Pin Select Output Registers RPOR16 and RPOR17 (see Register 9-30 and Register 9-31). Added the following two registers: * "RPOR16: Peripheral Pin Select Output Register 16" * "RPOR17: Peripheral Pin Select Output Register 17" Removed the following sections: * 9.4.2 "Available Peripherals" * 9.4.3.2 "Virtual Input Pins" * 9.4.3.4 "Peripheral Mapping" * 9.4.5 "Considerations for Peripheral Pin Selection" (and all subsections) Section 14.0 "High-Speed PWM" Added Note 1 (remappable pin reference) to Figure 14-1. Added Note 2 (Duty Cycle resolution) to PWM Master Duty Cycle Register (Register 14-5), PWM Generator Duty Cycle Register (Register 14-7), and PWM Secondary Duty Cycle Register (Register 14-8). Added Note 2 and Note 3 and updated bit information for CLSRC and FLTSRC in the PWM Fault Current-Limit Control Register (Register 14-15). Section 15.0 "Serial Peripheral Interface (SPI)" DS70318F-page 366 Removed the following sections, which are now available in the related section of the dsPIC33F/PIC24H Family Reference Manual: * 15.1 "Interrupts" * 15.2 "Receive Operations" * 15.3 "Transmit Operations" * 15.4 "SPI Setup" (retained Figure 15-1: SPI Module Block Diagram) (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-1: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 16.0 "Inter-Integrated Circuit (I2CTM)" Update Description Removed the following sections, which are now available in the related section of the dsPIC33F/PIC24H Family Reference Manual: * 16.3 "I2C Interrupts" * 16.4 "Baud Rate Generator" (retained Figure 16-1: I2C Block Diagram) * 16.5 "I2C Module Addresses * 16.6 "Slave Address Masking" * 16.7 "IPMI Support" * 16.8 "General Call Address Support" * 16.9 "Automatic Clock Stretch" * 16.10 "Software Controlled Clock Stretching (STREN = 1)" * 16.11 "Slope Control" * 16.12 "Clock Arbitration" * 16.13 "Multi-Master Communication, Bus Collision, and Bus Arbitration Section 17.0 "Universal Removed the following sections, which are now available in the related Asynchronous Receiver Transmitter section of the dsPIC33F/PIC24H Family Reference Manual: (UART)" * 17.1 "UART Baud Rate Generator" * 17.2 "Transmitting in 8-bit Data Mode * 17.3 "Transmitting in 9-bit Data Mode * 17.4 "Break and Sync Transmit Sequence" * 17.5 "Receiving in 8-bit or 9-bit Data Mode" * 17.6 "Flow Control Using UxCTS and UxRTS Pins" * 17.7 "Infrared Support" Removed IrDA references and Note 1, and updated the bit and bit value descriptions for UTXINV (UxSTA<14>) in the UARTx Status and Control Register (see Register 17-2). Section 18.0 "High-Speed 10-bit Analog-to-Digital Converter (ADC)" Updated bit value information for Analog-to-Digital Control Register (see Register 18-1). Updated TRGSRC6 bit value for Timer1 period match in the Analog-toDigital Convert Pair Control Register 3 (see Register 18-8). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 367 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-1: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 23.0 "Electrical Characteristics" Update Description Updated Typ values for Thermal Packaging Characteristics (Table 23-3). Removed Typ value for DC Temperature and Voltage Specifications parameter DC12 (Table 23-4). Updated all Typ values and conditions for DC Characteristics: Operating Current (IDD), updated last sentence in Note 2 (Table 23-5). Updated all Typ values for DC Characteristics: Idle Current (IIDLE) (see Table 23-6). Updated all Typ values for DC Characteristics: Power Down Current (IPD) (see Table 23-7). Updated all Typ values for DC Characteristics: Doze Current (IDOZE) (see Table 23-8). Added Note 4 (reference to new table containing digital-only and analog pin information, as well as Current Sink/Source capabilities) in the I/O Pin Input Specifications (Table 23-9). Updated Max value for BOR electrical characteristics parameter BO10 (see Table 23-11). Swapped Min and Typ values for Program Memory parameters D136 and D137 (Table 23-12). Updated Typ values for Internal RC Accuracy parameter F20 and added Extended temperature range to table heading (see Table 23-19). Removed all values for Reset, Watchdog Timer, Oscillator Start-up Timer, and Power-up Timer parameter SY20 and updated conditions, which now refers to Section 20.4 "Watchdog Timer (WDT)" and LPRC parameter F21a (see Table 23-22). Added specifications to High-Speed PWM Module Timing Requirements for Tap Delay (Table 23-29). Updated Min and Max values for 10-bit High-Speed Analog-to-Digital Module parameters AD01 and AD11 (see Table 23-36). Updated Max value and unit of measure for DAC AC Specification (see Table 23-40). DS70318F-page 368 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Revision C and D (March 2009) This revision includes minor typographical and formatting changes throughout the data sheet text. Global changes include: * Changed all instances of OSCI to OSC1 and OSCO to OSC2 * Changed all instances of PGCx/EMUCx and PGDx/EMUDx (where x = 1, 2, or 3) to PGECx and PGEDx * Changed all instances of VDDCORE and VDDCORE/ VCAP to VCAP/VDDCORE Other major changes are referenced by their respective section in the following table. TABLE A-2: MAJOR SECTION UPDATES Section Name "High-Performance, 16-bit Digital Signal Controllers" Update Description Added "Application Examples" to list of features Updated all pin diagrams to denote the pin voltage tolerance (see "Pin Diagrams"). Added Note 2 to the 28-Pin QFN-S and 44-Pin QFN pin diagrams, which references pin connections to VSS. Section 1.0 "Device Overview" Added ACMP1-ACMP4 pin names and Peripheral Pin Select capability column to Pinout I/O Descriptions (see Table 1-1). Section 2.0 "Guidelines for Getting Started with 16-bit Digital Signal Controllers" Added new section to the data sheet that provides guidelines on getting started with 16-bit Digital Signal Controllers. Section 3.0 "CPU" Updated CPU Core Block Diagram with a connection from the DSP Engine to the Y Data Bus (see Figure 3-1). Vertically extended the X and Y Data Bus lines in the DSP Engine Block Diagram (see Figure 3-3). Section 4.0 "Memory Organization" Updated Reset value for ADCON in Table 4-25. Removed reference to dsPIC33FJ06GS102 devices in the PMD Register Map and updated bit definitions for PMD1 and PMD6, and removed PMD7 (see Table 4-43). Added a new PMD Register Map, which references dsPIC33FJ06GS102 devices (see Table 4-44). Updated RAM stack address and SPLIM values in the third paragraph of Section 4.2.6 "Software Stack" Removed Section 4.2.7 "Data Ram Protection Feature". Section 5.0 "Flash Program Memory" (c) 2008-2012 Microchip Technology Inc. Updated Section 5.3 "Programming Operations" with programming time formula. DS70318F-page 369 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-2: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 8.0 "Oscillator Configuration" Update Description Added Note 2 to the Oscillator System Diagram (see Figure 8-1). Added a paragraph regarding FRC accuracy at the end of Section 8.1.1 "System Clock Sources". Added Note 1 and Note 2 to the OSCON register (see Register ). Added Note 1 to the OSCTUN register (see Register 8-4). Added Note 3 to Section 8.4.2 "Oscillator Switching Sequence". Section 10.0 "I/O Ports" Removed Table 9-1 and added reference to pin diagrams for I/O pin availability and functionality. Added paragraph on ADPCFG register default values to Section 10.3 "Configuring Analog Port Pins". Added Note box regarding PPS functionality with input mapping to Section 10.6.2.1 "Input Mapping". Section 15.0 "High-Speed PWM" Updated Note 2 in the PTCON register (see Register 15-1). Added Note 4 to the PWMCONx register (see Register 15-6). Updated Notes for the PHASEx and SPHASEx registers (see Register 15-9 and Register 15-10, respectively). Section 16.0 "Serial Peripheral Interface (SPI)" Added Note 2 and Note 3 to the SPIxCON1 register (see Register 16-2). Updated the Notes in the UxMode register (see Register 18-1). Section 18.0 "Universal Asynchronous Receiver Transmitter Updated the UTXINV bit settings in the UxSTA register and added Note 1 (UART)" (see Register 18-2). Section 19.0 "High-Speed 10-bit Analog-to-Digital Converter (ADC)" Updated the SLOWCLK and ADCS<2:0> bit settings and updated Note 1in the ADCON register (see Register 19-1). Removed all notes in the ADPCFG register and replaced them with a single note (see Register 19-4). Updated the SWTRGx bit settings in the ADCPCx registers (see Register 19-5, Register 19-6, Register 19-7, and Register 19-8). DS70318F-page 370 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-2: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 24.0 "Electrical Characteristics" Update Description Updated Typical values for Thermal Packaging Characteristics (see Table 24-3). Updated Min and Max values for parameter DC12 (RAM Data Retention Voltage) and added Note 4 (see Table 24-4). Updated Characteristics for I/O Pin Input Specifications (see Table 24-9). Added ISOURCE to I/O Pin Output Specifications (see Table 24-10). Updated Program Memory values for parameters 136, 137, and 138 (renamed to 136a, 137a, and 138a), added parameters 136b, 137b, and 138b, and added Note 2 (see Table 24-12). Added parameter OS42 (GM) to the External Clock Timing Requirements (see Table 24-16). Updated Conditions for symbol TPDLY (Tap Delay) and added symbol ACLK (PWM Input Clock) to the High-Speed PWM Module Timing Requirements (see Table 24-29). Updated parameters AD01 and AD02 in the 10-bit High-Speed Analog-toDigital Module Specifications (see Table 24-36). Updated parameters AD50b, AD55b, and AD56b, and removed parameters AD57b and AD60b from the 10-bit High-Speed Analog-to-Digital Module Timing Requirements (see Table 24-37). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 371 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Revision E (December 2009) The revision includes the following global update: * Added Note 2 to the shaded table that appears at the beginning of each chapter. This new note provides information regarding the availability of registers and their associated bits This revision also includes minor typographical and formatting changes throughout the data sheet text. All other major changes are referenced by their respective section in the following table. TABLE A-3: MAJOR SECTION UPDATES Section Name Update Description "16-bit Microcontrollers and Digital Signal Controllers (up to 16 KB Flash and up to 2 KB SRAM) with HighSpeed PWM, ADC and Comparators" Changed CN6 to CN5 on pin 16 of dsPIC33FJ16GS502 28-pin SPDIP, SOIC pin diagram. Section 2.0 "Guidelines for Getting Started with 16-bit Digital Signal Controllers" Removed the 10 Ohm resistor from Figure 2-1. Section 4.0 "Memory Organization" Renamed bit 13 of the REFOCON SFR in the System Control Register Map from ROSIDL to ROSSLP and changed the All Resets value from `0000' to `2300' for the ACLKCON SFR (see 4-41). Section 8.0 "Oscillator Configuration" Updated the default reset values from R/W-0 to R/W-1 for the SELACLK and APSTSCLR<2:0> bits in the ACLKCON register (see Register 8-5). Renamed the ROSIDL bit to ROSSLP in the REFOCON register (see Register 8-6). Section 9.0 "Power-Saving Features" Updated the last paragraph of Section 9.2.2 "Idle Mode" to clarify when instruction execution begins. Added Note 1 to the PMD1 register (see Register 9-1). Section 10.0 "I/O Ports" Changed the reference to digital-only pins to 5V tolerant pins in the second paragraph of Section 10.2 "Open-Drain Configuration". Section 15.0 "High-Speed PWM" Updated the smallest pulse width value from 0x0008 to 0x0009 in Note 1 of the shaded note that follows the MDC register (see Register 15-5). Updated the smallest pulse width value from 0x0008 to 0x0009 and the maximum pulse width value from 0x0FFEF to 0x0008 in Note 2 of the shaded note that follows the PDCx and SDCx registers (see Register 15-7 and Register 15-8). Added Note 2 and updated the FLTDAT<1:0> and CLDAT<1:0> bits, changing the word `data' to `state' in the IOCONx register (see Register 15-14). Section 18.0 "Universal Asynchronous Receiver Transmitter (UART)" Updated the two baud rate range features to: 10 Mbps to 38 bps at 40 MIPS. Section 19.0 "High-Speed 10-bit Analog-to-Digital Converter (ADC)" Updated Note 1 in the ADCPC0 register (see Register 19-5). Updated Note 3 in the ADCPC1 register (see Register 19-6). Updated Note 2 in the ADCPC2 and ADCPC3 registers (see Register 197 and Register 19-8). DS70318F-page 372 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-3: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 21.0 "Special Features" Update Description Updated the second paragraph and removed the fourth paragraph in Section 21.1 "Configuration Bits". Updated the Device Configuration Register Map (see Table 21-1). Section 24.0 "Electrical Characteristics" Updated the Absolute Maximum Ratings for high temperature and added Note 4. Updated Idle Current (IIDLE) Typical values in Table 24-6. Updated the Typ and Max values for parameter DI50 in the I/O Pin Input Specifications table (see Table 24-9). Updated the Typ and Max values for parameter DO10 and DO27 and the Min and Typ values for parameter DO20 in the I/O Pin Output Specifications (see Table 24-10). Added parameter numbers to the Auxiliary PLL Clock Timing Specifications (see Table 24-18). Added parameters numbers and updated the Internal RC Accuracy Min, Typ, and Max values (see Table 24-19 and Table 24-20). Added parameter numbers, Note 2, updated the Min and Typ parameter values for MP31 and MP32, and removed the conditions for MP10 and MP11 in the High-Speed PWM Module Timing Requirements (see Table 24-29). Updated the SPIx Module Slave Mode (CKE = 1) Timing Characteristics (see Table 24-14). Added parameter IM51 to the I2Cx Bus Data Timing Requirements (Master Mode) (see Table 24-34). Updated the Max value for parameter AD33 in the 10-bit High-Speed Analog-to-Digital Module Specifications (see Table 24-36). Updated the titles and added parameter numbers to the Comparator and DAC Module Specifications (see Table 24-38 and Table 24-39) and the DAC Output Buffer Specifications (see Table 24-40). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 373 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Revision F (January 2012) All occurrences of VDDCORE have been removed throughout the document. This revision also includes minor typographical and formatting changes throughout the data sheet text. All other major changes are referenced by their respective section in the following table. TABLE A-4: MAJOR SECTION UPDATES Section Name Update Description "16-bit Digital Signal Controllers (up Added the VTLA package to the dsPIC33FJ16GS404 and to 16 KB Flash and up to 2 KB dsPIC33FJ16GS504 devices (see TABLE 1: "dsPIC33FJ06GS101/X02 SRAM) with High-Speed PWM, ADC, and dsPIC33FJ16GSX02/X04 Controller Families"). and Comparators" Added the "Referenced Sources" section. The following updates were made to the "Pin Diagrams" section: * Added 5V tolerant pin shading to pins 24-26 in the 28-pin SPDIP, SOIC package for the dsPIC33FJ16GS402 * Updated pin 31 of the 44-pin QFN package for the dsPIC33FJ16GS404 * Added VTLA pin diagrams for the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices Section 1.0 "Device Overview" Removed the Precision Band Gap Reference from the device block diagram (see Figure 1-1). Updated the Pinout I/O Descriptions for AVDD, and AVSS (see Table 1-1). Section 2.0 "Guidelines for Getting Started with 16-bit Digital Signal Controllers" Updated the Minimum Recommended Connection (see Figure 2-1). Section 8.0 "Oscillator Configuration" Updated the Oscillator System Diagram (see Figure 8-1). Added auxiliary clock configuration restrictions in Section 8.2 "Auxiliary Clock Generation". Updated or added notes regarding register reset on a POR (see Register 8-1 through Register 8-5). Section 19.0 "High-Speed 10-bit Analog-to-Digital Converter (ADC)" Added Note 2 to ADCON: Analog-to-Digital Control Register (see Register 19-1). Removed all notes from ADSTAT: Analog-to-Digital Status Register (see Register 19-2). Section 20.0 "High-Speed Analog Comparator" Updated the Comparator Module Block Diagram (see Figure 20-1). Section 21.0 "Special Features" Add a new paragraph at the beginning of Section 21.1 "Configuration Bits". Added the RTSP Effect column to the dsPIC33F Configuration Bits Description table (see Table 21-2). Updated the Connections for the On-chip Voltage Regulator diagram (see Figure 21-1). Updated the first paragraph of Section 21.7 "In-Circuit Debugger". DS70318F-page 374 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-4: MAJOR SECTION UPDATES (CONTINUED) Section Name Section 24.0 "Electrical Characteristics" Update Description Updated the Absolute Maximum Ratings. Updated the Operating MIPS vs. Voltage (see Table 24-1). Updated parameter DC10 and Note 4, and removed parameter DC18 from the DC Temperature and Voltage Specifications (see Table 24-4). Updated Note 2 in the IDD Operating Current specification (see Table 24-5). Updated all Typical values and Note 2 in the IIDLE Operating Current specification (see Table 24-6). Updated Typical values for parameters DC60d, DC60a, DC60b, and DC60c, and Note 2 in the IPD Operating Current specification (see Table 24-7). Added all Typical values and Note 2 in the IDOZE Operating Current specification (see Table 24-8). Updated parameter DI19 and DI50, added parameters DI128, DI129, DI60a, DI60b, and DI60c, and removed parameter DI57 in the I/O Pin Input Specifications (see Table 24-9). Revised all I/O Pinout Output Specifications (see Table 24-10). Added Notes 2 and 3 to the BOR Electrical Characteristics (see Table 2411). Added Note 1 to Internal Voltage Regulator Specifications (see Table 24-13). Updated the External Clock Timing diagram (see Figure 24-2). Added Note 2 to the PLL Clock Timing Specifications (see Table 24-17). Removed Note 2 from the Internal FRC Accuracy (see Table 24-19). Updated parameter DO31 and DO32 in the I/O Timing Requirements (see Table 24-21). Updated the External Clock Timing Requirements for Timer1, Timer2, and Timer3 (see Table 24-23, Table 24-24, and Table 24-25, respectively). Updated parameters OC15 and OC20 in the Simple OC/PWM Mode Timing Requirements (see Table 24-28). Revised all SPIx Module Timing Characteristics diagrams and all Timing Requirements (see Figure 24-11 through Figure 24-18 and Table 24-30 through Table 24-37, respectively). Added Note 2 to the 10-bit High-Speed ADC Module Specifications (see Table 24-40). Added Note 2 to the 10-bit High-Speed ADC Module Timing Requirements (see Table 24-41). Added Note 2 to the Comparator Module Specifications (see Table 24-42). Added parameter DA08 and Note 2 in the DAC Module Specifications (see Table 24-43). Updated parameter DA16 and Note 2 in the DAC Output Buffer DC Specifications (see Table 24-44). (c) 2008-2012 Microchip Technology Inc. DS70318F-page 375 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 TABLE A-4: MAJOR SECTION UPDATES (CONTINUED) Section Name Update Description Section 26.0 "50 MIPS Electrical Characteristics" Added new chapter in support of 50 MIPS devices. Section 27.0 "DC and AC Device Characteristics Graphs" Added new chapter. Section 28.0 "Packaging Information" Added 44-pin VTLA package marking information and diagrams (see Section 28.1 "Package Marking Information" and Section 28.2 "Package Details", respectively). "Product Identification System" Added the TL package definition. DS70318F-page 376 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 INDEX A AC Characteristics ............................................ 298, 336, 343 Internal RC Accuracy ................................................ 301 Load Conditions ................................................ 298, 336 Alternate Vector Table (AIVT) ............................................. 95 Arithmetic Logic Unit (ALU)................................................. 35 Assembler MPASM Assembler................................................... 282 B Barrel Shifter ....................................................................... 39 Bit-Reversed Addressing .................................................... 74 Example ...................................................................... 75 Implementation ........................................................... 74 Sequence Table (16-Entry)......................................... 75 Block Diagrams 16-bit Timer1 Module ................................................ 181 Comparator ............................................................... 261 Connections for On-Chip Voltage Regulator............. 268 DSP Engine ................................................................ 36 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 16 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CPU Core ........................................................... 30 I2C............................................................................. 224 Input Capture ............................................................ 189 Oscillator System ...................................................... 133 Output Compare ....................................................... 191 PLL............................................................................ 135 Reset System.............................................................. 87 Shared Port Structure ............................................... 153 Simplified Conceptual High-Speed PWM ................. 197 SPI ............................................................................ 217 Timer2/3 (32-bit) ....................................................... 185 Type B Timer ............................................................ 183 Type C Timer ............................................................ 183 UART ........................................................................ 231 Watchdog Timer (WDT) ............................................ 269 Brown-out Reset (BOR) .................................................... 265 C C Compilers MPLAB C18 .............................................................. 282 Clock Switching................................................................. 144 Enabling .................................................................... 144 Sequence.................................................................. 144 Code Examples Erasing a Program Memory Page............................... 85 Initiating a Programming Sequence............................ 86 Loading Write Buffers ................................................. 86 Port Write/Read ........................................................ 154 PWRSAV Instruction Syntax..................................... 145 Code Protection ........................................................ 265, 271 CodeGuard Security ......................................................... 265 Configuration Bits.............................................................. 265 Configuration Register Map .............................................. 265 Configuring Analog Port Pins ............................................ 154 CPU Control Registers ........................................................ 32 CPU Clocking System....................................................... 134 PLL Configuration ..................................................... 135 Selection ................................................................... 134 Sources..................................................................... 134 (c) 2008-2012 Microchip Technology Inc. Customer Change Notification Service............................. 381 Customer Notification Service .......................................... 381 Customer Support............................................................. 381 D DAC .................................................................................. 262 Output Range ........................................................... 262 Data Accumulators and Adder/Subtracter .......................... 37 Data Space Write Saturation ...................................... 39 Overflow and Saturation ............................................. 37 Round Logic ............................................................... 38 Write Back .................................................................. 38 Data Address Space........................................................... 43 Alignment.................................................................... 43 Memory Map for dsPIC33FJ06GS101/102 Devices with 256 Bytes of RAM............................................... 44 Memory Map for dsPIC33FJ06GS202 Device with 1 KB RAM ................................................................... 45 Memory Map for dsPIC33FJ16GS402/404/502/504 Devices with 2 KB RAM .......................................... 46 Near Data Space ........................................................ 43 Software Stack ........................................................... 71 Width .......................................................................... 43 DC and AC Characteristics Graphs and Tables ................................................... 347 DC Characteristics.................................................... 286, 340 Doze Current (IDOZE)........................................ 292, 342 High Temperature..................................................... 332 I/O Pin Input Specifications ...................................... 293 I/O Pin Output Specifications............................ 295, 334 Idle Current (IIDLE) ............................................ 290, 341 Operating Current (IDD) .................................... 288, 340 Operating MIPS vs. Voltage ..................................... 332 Power-Down Current (IPD)........................................ 291 Power-down Current (IPD) ........................................ 333 Program Memory.............................................. 297, 335 Temperature and Voltage......................................... 332 Temperature and Voltage Specifications.................. 287 Thermal Operating Conditions.................................. 332 Development Support ....................................................... 281 Doze Mode ....................................................................... 146 DSP Engine ........................................................................ 35 Multiplier ..................................................................... 37 E EBCONx (Leading-Edge Blanking Control) ...................... 214 Electrical Characteristics .......................................... 285, 339 AC............................................................................. 336 AC Characteristics and Timing Parameters ..... 298, 343 BOR.......................................................................... 296 Equations Device Operating Frequency.................................... 134 FOSC Calculation ...................................................... 135 XT with PLL Mode Example ..................................... 135 Errata .................................................................................. 13 F Fail-Safe Clock Monitor (FSCM)....................................... 144 Flash Program Memory ...................................................... 81 Control Registers........................................................ 82 Operations .................................................................. 82 Programming Algorithm.............................................. 85 RTSP Operation ......................................................... 82 Table Instructions ....................................................... 81 DS70318F-page 377 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Flexible Configuration ....................................................... 265 H High Temperature Electrical Characteristics..................... 331 High-Speed 10-bit Analog-to-Digital Converter (ADC)...... 237 High-Speed Analog Comparator ....................................... 261 High-Speed PWM ............................................................. 195 I I/O Ports ............................................................................ 153 Parallel I/O (PIO)....................................................... 153 Write/Read Timing .................................................... 154 I2 C Operating Modes ...................................................... 223 Registers ................................................................... 225 In-Circuit Debugger ........................................................... 270 In-Circuit Emulation........................................................... 265 In-Circuit Serial Programming (ICSP) ....................... 265, 270 Input Capture .................................................................... 189 Registers ................................................................... 190 Input Change Notification.................................................. 154 Instruction Addressing Modes............................................. 71 File Register Instructions ............................................ 71 Fundamental Modes Supported.................................. 72 MAC Instructions......................................................... 72 MCU Instructions ........................................................ 71 Move and Accumulator Instructions ............................ 72 Other Instructions........................................................ 72 Instruction Set Overview ................................................................... 276 Summary................................................................... 273 Instruction-Based Power-Saving Modes ........................... 145 Idle ............................................................................ 146 Sleep ......................................................................... 145 Interfacing Program and Data Memory Spaces .................. 76 Internal RC Oscillator Use with WDT ........................................................... 269 Internet Address................................................................ 381 Interrupt Control and Status Registers................................ 98 IECx ............................................................................ 98 IFSx............................................................................. 98 INTCON1 .................................................................... 98 INTCON2 .................................................................... 98 INTTREG .................................................................... 98 IPCx ............................................................................ 98 Interrupt Setup Procedures ............................................... 132 Initialization ............................................................... 132 Interrupt Disable........................................................ 132 Interrupt Service Routine .......................................... 132 Trap Service Routine ................................................ 132 Interrupt Vector Table (IVT) ................................................ 95 Interrupts Coincident with Power Save Instructions.......... 146 J JTAG Boundary Scan Interface ........................................ 265 JTAG Interface .................................................................. 270 M Memory Organization.......................................................... 41 Microchip Internet Web Site .............................................. 381 Modulo Addressing ............................................................. 73 Applicability ................................................................. 74 Operation Example ..................................................... 73 Start and End Address ................................................ 73 W Address Register Selection .................................... 73 MPLAB ASM30 Assembler, Linker, Librarian ................... 282 DS70318F-page 378 MPLAB Integrated Development Environment Software.. 281 MPLAB PM3 Device Programmer .................................... 284 MPLAB REAL ICE In-Circuit Emulator System ................ 283 MPLINK Object Linker/MPLIB Object Librarian ................ 282 O Open-Drain Configuration................................................. 154 Oscillator Configuration .................................................... 133 Output Compare ............................................................... 191 P Packaging ......................................................................... 351 Details....................................................................... 353 Marking ..................................................................... 351 Peripheral Module Disable (PMD) .................................... 146 Pinout I/O Descriptions (table)............................................ 17 Power-on Reset (POR)....................................................... 92 Power-Saving Features .................................................... 145 Clock Frequency and Switching ............................... 145 Program Address Space..................................................... 41 Construction ............................................................... 76 Data Access from Program Memory Using Program Space Visibility ................................................... 79 Data Access from Program Memory Using Table Instructions .................................................................... 78 Data Access from, Address Generation ..................... 77 Memory Maps ............................................................. 41 Table Read Instructions TBLRDH ............................................................. 78 TBLRDL.............................................................. 78 Visibility Operation ...................................................... 79 Program Memory Interrupt Vector ........................................................... 42 Organization ............................................................... 42 Reset Vector ............................................................... 42 R Reader Response............................................................. 382 Registers .................................................................................. 214 ACLKCON (Auxiliary Clock Divisor Control)............. 142 ALTDTRx (PWM Alternate Dead-Time).................... 207 Analog-to-Digital Base Register (ADBASE).............. 248 Analog-to-Digital Control Register (ADCON)............ 245 Analog-to-Digital Convert Pair Control Register 0 (ADCPC0)......................................................... 249 Analog-to-Digital Convert Pair Control Register 1 (ADCPC1)......................................................... 252 Analog-to-Digital Convert Pair Control Register 2 (ADCPC2)......................................................... 255 Analog-to-Digital Convert Pair Control Register 3 (ADCPC3)......................................................... 258 Analog-to-Digital Port Configuration Register (ADPCFG) 248 Analog-to-Digital Status Register (ADSTAT) ............ 247 CLKDIV (Clock Divisor) ............................................ 139 CMPCPNx (Comparator Control) ............................. 263 CMPDACx (Comparator DAC Control)..................... 264 CORCON (Core Control) ...................................... 34, 99 DTRx (PWMx Dead-Time)........................................ 207 FCLCONx (PWMx Fault Current-Limit Control)........ 211 I2CxCON (I2Cx Control) ........................................... 226 I2CxMSK (I2Cx Slave Mode Address Mask) ............ 230 I2CxSTAT (I2Cx Status) ........................................... 228 ICxCON (Input Capture x Control)............................ 190 IEC0 (Interrupt Enable Control 0) ............................. 110 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 IEC1 (Interrupt Enable Control 1) ............................. 112 IEC3 (Interrupt Enable Control 3) ............................. 113 IEC4 (Interrupt Enable Control 4) ............................. 113 IEC5 (Interrupt Enable Control 5) ............................. 114 IFS0 (Interrupt Flag Status 0) ................................... 103 IFS1 (Interrupt Flag Status 1) ................................... 105 IFS3 (Interrupt Flag Status 3) ................................... 106 IFS4 (Interrupt Flag Status 4) ................................... 106 IFS5 (Interrupt Flag Status 5) ................................... 107 IFS6 (Interrupt Flag Status 6) ........................... 108, 115 IFS7 (Interrupt Flag Status 7) ........................... 109, 116 INTCON1 (Interrupt Control 1).................................. 100 INTTREG Interrupt Control and Status ..................... 131 IOCONx (PWMx I/O Control) .................................... 209 IPC0 (Interrupt Priority Control 0) ............................. 117 IPC1 (Interrupt Priority Control 1) ............................. 118 IPC14 (Interrupt Priority Control 14) ......................... 123 IPC16 (Interrupt Priority Control 16) ......................... 123 IPC2 (Interrupt Priority Control 2) ............................. 119 IPC23 (Interrupt Priority Control 23) ......................... 124 IPC24 (Interrupt Priority Control 24) ......................... 125 IPC25 (Interrupt Priority Control 25) ......................... 126 IPC26 (Interrupt Priority Control 26) ......................... 127 IPC27 (Interrupt Priority Control 27) ......................... 128 IPC28 (Interrupt Priority Control 28) ......................... 129 IPC29 (Interrupt Priority Control 29) ......................... 130 IPC3 (Interrupt Priority Control 3) ............................. 120 IPC4 (Interrupt Priority Control 4) ............................. 121 IPC5 (Interrupt Priority Control 5) ............................. 122 IPC7 (Interrupt Priority Control 7) ............................. 122 MDC (PWM Master Duty Cycle) ............................... 201 NVMCON (Flash Memory Control) ............................. 83 NVMKEY (Nonvolatile Memory Key) .......................... 84 OCxCON (Output Compare x Control) ..................... 193 OSCCON (Oscillator Control) ................................... 137 OSCTUN (Oscillator Tuning) .................................... 141 PLLFBD (PLL Feedback Divisor).............................. 140 PMD1 (Peripheral Module Disable Control 1)........... 147 PMD2 (Peripheral Module Disable Control 2)........... 148 PMD3 (Peripheral Module Disable Control 3)........... 149 PMD4 (Peripheral Module Disable Control 4)........... 149 PMD6 (Peripheral Module Disable Control 6)........... 150 PMD7 (Peripheral Module Disable Control 7)........... 151 PTCON (PWM Time Base Control) .......................... 199 PWMCAPx (Primary PWMx Time Base Capture)..... 215 PWMCONx (PWMx Control)..................................... 202 RCON (Reset Control) ................................................ 88 REFOCON (Reference Oscillator Control) ............... 143 RPINR0 (Peripheral Pin Select Input 0).................... 159 RPINR1 (Peripheral Pin Select Input 1).................... 160 RPINR11 (Peripheral Pin Select Input 11)................ 163 RPINR18 (Peripheral Pin Select Input 18)................ 164 RPINR20 (Peripheral Pin Select Input 20)................ 165 RPINR21 (Peripheral Pin Select Input 21)................ 166 RPINR29 (Peripheral Pin Select Input 29)................ 167 RPINR3 (Peripheral Pin Select Input 3).................... 161 RPINR30 (Peripheral Pin Select Input 30)................ 168 RPINR31 (Peripheral Pin Select Input 31)................ 169 RPINR32 (Peripheral Pin Select Input 32)................ 170 RPINR33 (Peripheral Pin Select Input 33)................ 171 RPINR34 (Peripheral Pin Select Input 34)................ 172 RPINR7 (Peripheral Pin Select Input 7).................... 162 RPOR0 (Peripheral Pin Select Output 0).................. 172 RPOR1 (Peripheral Pin Select Output 1).................. 173 RPOR10 (Peripheral Pin Select Output 10).............. 177 (c) 2008-2012 Microchip Technology Inc. RPOR11 (Peripheral Pin Select Output 11) ............. 178 RPOR12 (Peripheral Pin Select Output 12) ............. 178 RPOR13 (Peripheral Pin Select Output 13) ............. 179 RPOR14 (Peripheral Pin Select Output 14) ............. 179 RPOR16 (Peripheral Pin Select Output 16) ............. 180 RPOR17 (Peripheral Pin Select Output 17) ............. 180 RPOR2 (Peripheral Pin Select Output 2) ................. 173 RPOR3 (Peripheral Pin Select Output 3) ................. 174 RPOR4 (Peripheral Pin Select Output 4) ................. 174 RPOR5 (Peripheral Pin Select Output 5) ................. 175 RPOR6 (Peripheral Pin Select Output 6) ................. 175 RPOR7 (Peripheral Pin Select Output 7) ................. 176 RPOR8 (Peripheral Pin Select Output 8) ................. 176 RPOR9 (Peripheral Pin Select Output 9) ................. 177 SEVTCMP (PWM Special Event Compare) ............. 201 SPIxCON1 (SPIx Control 1) ..................................... 219 SPIxCON2 (SPIx Control 2) ..................................... 221 SPIxSTAT (SPIx Status and Control) ....................... 218 SR (CPU STATUS) .................................................... 99 SR (CPU Status) ........................................................ 32 STRIGx (PWMx Secondary Trigger Compare Value) .... 213 T1CON (Timer1 Control) .......................................... 182 TRGCONx (PWMx Trigger Control) ......................... 208 TRIGx (PWMx Primary Trigger Compare Value) ..... 213 TxCON (Timer Control, x = 2)................................... 186 TyCON (Timer Control, y = 3)................................... 187 UxMODE (UARTx Mode) ......................................... 232 UxSTA (UARTx Status and Control) ........................ 234 Reset Configuration Mismatch.............................................. 93 Illegal Opcode....................................................... 87, 93 Trap Conflict ............................................................... 93 Uninitialized W Register ................................. 87, 93, 94 Reset Sequence ................................................................. 95 Resets ................................................................................ 87 Resources Required for Digital PFC............................. 23, 26 Resources Required for Digital Phase-Shift ZVT Converter28 Revision History................................................................ 365 S Serial Peripheral Interface (SPI) ....................................... 217 Software RESET Instruction (SWR) ................................... 93 Software Simulator (MPLAB SIM) .................................... 283 Software Stack Pointer, Frame Pointer CALL Stack Frame ..................................................... 71 Special Features of the CPU ............................................ 265 Symbols Used in Opcode Descriptions ............................ 274 T Temperature and Voltage Specifications AC..................................................................... 298, 336 Timer1 .............................................................................. 181 Timer2/3 ........................................................................... 183 Timing Diagrams Analog-to-Digital Conversion per Input..................... 327 Brown-out Situations .................................................. 92 External Clock .......................................................... 299 High-Speed PWM..................................................... 309 High-Speed PWM Fault............................................ 309 I/O............................................................................. 302 I2Cx Bus Data (Master Mode) .................................. 322 I2Cx Bus Data (Slave Mode) .................................... 324 I2Cx Bus Start/Stop Bits (Master Mode)................... 322 I2Cx Bus Start/Stop Bits (Slave Mode)..................... 324 Input Capture (CAPx) ............................................... 307 DS70318F-page 379 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 OC/PWM ................................................................... 308 Output Compare (OCx) ............................................. 307 Reset, Watchdog Timer, Oscillator Start-up Timer and Power-up Timer ................................................ 303 Timer1, 2, 3 External Clock....................................... 305 Timing Requirements External Clock ................................................... 299, 343 I/O ............................................................................. 302 Input Capture ............................................................ 307 SPIx Master Mode (CKE = 0).................................... 337 SPIx Module Master Mode (CKE = 1)....................... 337 SPIx Module Slave Mode (CKE = 0)......................... 338 SPIx Module Slave Mode (CKE = 1)......................... 338 Timing Specifications 10-bit Analog-to-Digital Conversion Requirements ... 327 High-Speed PWM Requirements .............................. 309 I2Cx Bus Data Requirements (Master Mode) ........... 323 I2Cx Bus Data Requirements (Slave Mode) ............. 325 Output Compare Requirements ................................ 307 PLL Clock.......................................................... 300, 336 Reset, Watchdog Timer, Oscillator Start-up Timer, DS70318F-page 380 Power-up Timer and Brown-out Reset Requirements ................................................... 304 Simple OC/PWM Mode Requirements ............. 308, 346 Timer1 External Clock Requirements ............... 305, 344 Timer2 External Clock Requirements ............... 306, 345 Timer3 External Clock Requirements ............... 306, 345 U Universal Asynchronous Receiver Transmitter (UART) ... 231 Using the RCON Status Bits............................................... 94 V Voltage Regulator (On-Chip) ............................................ 268 W Watchdog Time-out Reset (WDTO).................................... 93 Watchdog Timer (WDT)............................................ 265, 269 Programming Considerations ................................... 269 WWW Address ................................................................. 381 WWW, On-Line Support ..................................................... 13 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives * * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://microchip.com/support CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under "Support", click on "Customer Change Notification" and follow the registration instructions. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 381 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. TO: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Literature Number: DS70318F Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS70318F-page 382 (c) 2008-2012 Microchip Technology Inc. dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. dsPIC 33 FJ 06 GS1 02 T - 50 E / SP - XXX Examples: a) dsPIC33FJ06GS102-E/SP: SMPS dsPIC33, 6-Kbyte program memory, 28-pin, Extended temperature, SPDIP package. Microchip Trademark Architecture Flash Memory Family Program Memory Size (KB) Product Group Pin Count Tape and Reel Flag (if applicable) Speed (if applicable) Temperature Range Package Pattern Architecture: 33 = 16-bit Digital Signal Controller Flash Memory Family: FJ = Flash program memory, 3.3V Product Group: GS1 GS2 GS4 GS5 = = = = Switch Mode Power Supply (SMPS) family Switch Mode Power Supply (SMPS) family Switch Mode Power Supply (SMPS) family Switch Mode Power Supply (SMPS) family Pin Count: 01 02 04 = = = 18-pin 28-pin 44-pin Speed 50 = 50 MIPS Temperature Range: I E H = = = -40C to+85C (Industrial) -40C to+125C (Extended) -40C to+150C (High) Package: PT ML MM SO SP TL = = = = = = Plastic Thin Quad Flatpack - 10x10x1 mm body (TQFP) Plastic Quad Flat, No Lead Package - 8x8 mm body (QFN) Plastic Quad Flat, No Lead Package - 6x6x0.9 mm body (QFN-S) Plastic Small Outline - Wide - 7.50 mm body (SOIC) Skinny Plastic Dual In-Line - 300 mil body (SPDIP) Very Thin Leadless Array - 6x6 mm body (VTLA) (c) 2008-2012 Microchip Technology Inc. DS70318F-page 383 dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 NOTES: DS70318F-page 384 (c) 2008-2012 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2008-2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-61341-970-0 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2008-2012 Microchip Technology Inc. DS70318F-page 385 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-66-152-7160 Fax: 81-66-152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS70318F-page 386 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 11/29/11 (c) 2008-2012 Microchip Technology Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: dsPIC33FJ16GS504-E/ML dsPIC33FJ16GS504-I/PT dsPIC33FJ16GS502-E/MM dsPIC33FJ16GS504-E/PT dsPIC33FJ16GS402-E/SP dsPIC33FJ16GS402-I/SP dsPIC33FJ16GS402-I/MM dsPIC33FJ16GS404-I/ML dsPIC33FJ16GS404T-I/ML dsPIC33FJ16GS502-E/SP dsPIC33FJ16GS502T-I/SO dsPIC33FJ16GS402-E/SO dsPIC33FJ16GS502-E/SO dsPIC33FJ16GS402-E/MM dsPIC33FJ16GS504-I/ML dsPIC33FJ16GS402T-I/SO dsPIC33FJ16GS502-I/SP dsPIC33FJ16GS504T-I/ML dsPIC33FJ16GS502-I/MM dsPIC33FJ16GS404-E/ML dsPIC33FJ16GS404-E/PT dsPIC33FJ16GS402T-I/MM dsPIC33FJ16GS502T-I/MM dsPIC33FJ16GS502-I/SO dsPIC33FJ16GS404T-I/PT dsPIC33FJ16GS504T-I/PT dsPIC33FJ16GS504T-E/TL dsPIC33FJ16GS504T-I/TL dsPIC33FJ16GS404T-E/TL dsPIC33FJ16GS404T-I/TL dsPIC33FJ16GS404-E/TL dsPIC33FJ16GS404-I/TL dsPIC33FJ16GS504-E/TL dsPIC33FJ16GS504-I/TL dsPIC33FJ16GS402-50I/MM dsPIC33FJ16GS402-50I/SO dsPIC33FJ16GS402-50I/SP dsPIC33FJ16GS402-H/MM dsPIC33FJ16GS402-H/SO dsPIC33FJ16GS402-H/SP dsPIC33FJ16GS402T-50I/MM dsPIC33FJ16GS402T-50I/SO dsPIC33FJ16GS404-50I/ML dsPIC33FJ16GS404-50I/TL dsPIC33FJ16GS404-H/ML dsPIC33FJ16GS404-H/PT dsPIC33FJ16GS404-H/TL dsPIC33FJ16GS404T-50I/ML dsPIC33FJ16GS404T-50I/TL dsPIC33FJ16GS502-50I/MM dsPIC33FJ16GS502-50I/SO dsPIC33FJ16GS502-50I/SP dsPIC33FJ16GS502-H/MM dsPIC33FJ16GS502-H/SO dsPIC33FJ16GS502-H/SP dsPIC33FJ16GS502T-50I/MM dsPIC33FJ16GS502T-50I/SO dsPIC33FJ16GS504-50I/ML dsPIC33FJ16GS504-50I/TL dsPIC33FJ16GS504-H/ML dsPIC33FJ16GS504-H/PT dsPIC33FJ16GS504-H/TL dsPIC33FJ16GS504T-50I/ML dsPIC33FJ16GS504T-50I/TL dsPIC33FJ16GS404-50I/PT dsPIC33FJ16GS404T-50I/PT dsPIC33FJ16GS504-50I/PT dsPIC33FJ16GS504T-50I/PT dsPIC33FJ06GS202A-I/SS dsPIC33FJ06GS101A-I/P dsPIC33FJ06GS102A-I/TL dsPIC33FJ06GS102A-I/SS dsPIC33FJ06GS202A-I/SP dsPIC33FJ06GS102A-I/MM dsPIC33FJ06GS202A-I/TL dsPIC33FJ06GS102A-I/SP dsPIC33FJ06GS101A-I/SO dsPIC33FJ06GS202A-I/SO dsPIC33FJ06GS102A-I/SO dsPIC33FJ06GS202A-I/MM dsPIC33FJ06GS101A-I/SS dsPIC33FJ06GS101A-E/SO dsPIC33FJ06GS102A-E/SS dsPIC33FJ06GS102AT-I/SS dsPIC33FJ06GS101A-E/P dsPIC33FJ06GS202A-E/SP dsPIC33FJ06GS102A-E/SP dsPIC33FJ06GS202AT-I/TL dsPIC33FJ06GS102AT-E/SS dsPIC33FJ06GS202AT-I/MM dsPIC33FJ06GS202A-E/SO dsPIC33FJ06GS101AT-I/SS dsPIC33FJ06GS101AT-I/SO dsPIC33FJ06GS102AT-E/SO dsPIC33FJ06GS202AT-E/TL dsPIC33FJ06GS102AT-I/SO dsPIC33FJ06GS202AT-E/MM dsPIC33FJ06GS102AT-I/TL dsPIC33FJ06GS101AT-E/SS dsPIC33FJ06GS102A-E/TL