[AK8817VQ] AK8817VQ NTSC/PAL Digital Video Encoder General Description The AK8817VQ is a Digital Video Encoder for Portable and Mobile application. ITU-R BT.601 level compatible Y, Cb,and Cr signals which correspond to 27MHz or square pixel are encoded into either NTSC or PAL compatible composite video signal. Interface is made in HSYNC-, VSYNC- synchronized slave-mode operation or ITU-R.Bt656. AK8817VQ has 75ohm driver with LPF. It is possible to encode the VBID(CGMS-A) and WSS signal on the output video signal. Host Control interface is I2C Bus I/F. Features * * * * * * * * * * * * * * * * * * * NTSC-M, PAL-B, D, G, H, I Composite Video encoding Y:Cb:Cr 4:2:2 H/V Slave Operation / ITU-R.BT656 Interface Y filtering: 2 x over-sampling C filtering: 4 x over-sampling 9bit DAC Setup VBID ( CGMS-A ) Compatible WSS Compatible Operation Clock rate : 27MHz or Square-pixel Clock rate(NTSC:24.5454MHz/PAL29.50MHz) Video Amp with LPF On-chip Color Bar Output Black Burst Output Power Supply (AVDD, DVDD) 2.7V - 3.6V I/F Power Supply (PVDD) 1.6V - DVDD Power Down mode Monolithic CMOS 48pin LQFP (Pb Free) Temperature Range: -40 ~ 105C MS1113-E-00 2009/08 -1- [AK8817VQ] Block Diagram CLKIN CLKINV RSTN PDN SCL SDA VREF CLK Generator u-p I/F Register Timing Controller D[7:0] Input Data Control HDI Synchronization Control VDI IREF VREF Generator (Macrovision &) CGMS SYNC Generator Y Y LPF Filter (x 2 Interpolator) Cb Cr Cb/Cr LPF Filter (x 2 Interpolator) SAG 6dB AMP LPF 9-bit DAC U Cos SubCarrier Generator Color Bar Gen B.B. Gen C Sin VOUT DACOUT Chroma LPF Filter (x 2 Interpolator) TEST LOGIC UD[4:0] V PVDD PVSS DVDD DVSS AVDD AVSS MS1113-E-00 TEST ATPG 2009/08 -2- [AK8817VQ] Ordering Guide AK8817VQ 48pin LQFP Pin Assignment NC NC TEST D1 D0 PVDD PVSS VDI HDI SDA SCL NC 36 35 34 3332 31 30 29 28 2726 25 ATPG PDN RSTN DVSS DVDD NC VOUT BVSS SAG AVSS DACOUT NC 24 23 22 21 20 19 18 17 16 15 14 13 37 38 39 40 41 42 43 44 45 46 47 48 NC D2 D3 D4 D5 D6 D7 DVDD DVSS CLKIN CLKINV NC 1 2 3 4 5 6 7 8 9 10 11 12 NC NC UD0 UD1 UD2 UD3 UD4 VREF IREF AVDD NC NC MS1113-E-00 2009/08 -3- [AK8817VQ] Pin Functional Description Pin# Pin Name I/O Functional Outline 1 N.C. - For normal operation, left open. 2 N.C. - For normal operation, left open. 3 AVDD P Analog power supply pin. 4 IREF O 5 VREF O 6 UD4 O Test output pin. For normal operation, left open. 7 UD3 O Test output pin. For normal operation, left open. 8 UD2 O Test output pin. For normal operation, left open. 9 UD1 O Test output pin. For normal operation, left open. 10 UD0 O Test output pin. For normal operation, left open. 11 N.C. - For normal operation, left open. 12 N.C. - For normal operation, left open. 13 N.C. - For normal operation, left open. 14 CLKINV I 15 CLKIN I 16 DVSS G 17 DVDD P IREF output pin. Connect this pin to Analog ground via a 12k ohm resistor ( better than +/- 1% accuracy ). On-chip VREF output pin. AVSS level is output on this pin at PDN = L. Connect this pin to Analog Ground via a 0.1 uF or larger capacitor. Internal clock is inverted (internal operation timing edge is inverted.) Connect to either DVDD or DGND. Clock input pin. Input a clock which is synchronized with data. When to input 601 data : 27 MHz. When to input square pixel data : 24.5454 MHz ( NTSC )/ 29.50 MHz ( PAL ) Digital ground pin (digital core ground). Digital power supply pin (digital core power supply). Data Video Signal input pin (MSB). Hi-Z input is acceptable to this pin at PDN = L. Data Video Signal input pin. Hi-Z input is acceptable to this pin at PDN = L. Data Video Signal input pin. Hi-Z input is acceptable to this pin at PDN = L. Data Video Signal input pin. Hi-Z input is acceptable to this pin at PDN = L. Data Video Signal input pin. Hi-Z input is acceptable to this pin at PDN = L. Data Video Signal input pin. Hi-Z input is acceptable to this pin at PDN = L. 18 D7 I 19 D6 I 20 D5 I 21 D4 I 22 D3 I 23 D2 I 24 N.C. - For normal operation, left open. 25 N.C. - For normal operation, left open. 26 N.C. - For normal operation, left open. 27 TEST I For normal operation, connect to ground. 28 D1 I 29 D0 I 30 PVDD P Data Video Signal input pin. Hi-Z input is acceptable to this pin at PDN = L. Data Video Signal input pin (LSB). Hi-Z input is acceptable to this pin at PDN = L. Power supply pin for chip pad. MS1113-E-00 2009/08 -4- [AK8817VQ] Pin# Pin Name I/O 31 PVSS G 32 VDI I Functional Outline Ground pin for PVDD. Vertical SYNC signal input pin. Hi-Z input is acceptable to this pin at PDN = L. Horizontal SYNC signal input pin. Hi-Z input is acceptable to this pin at PDN = L. I2C data pin. This pin is pulled-up to PVDD. Hi-Z input is possible when PDN is at low. SDA input is not accepted during the reset sequence operation. I2C clock input pin An input level of lower-than-PVDD should be input. Hi-Z input is possible when PDN is at low. SCL input is not accepted during the reset sequence operation. 33 HDI I 34 SDA I/O 35 SCL I 36 N.C. - For normal operation, left open. 37 ATPG I For normal operation, connect to ground. Power Down Pin. After returning from PD mode to normal operation, RESET Sequence should be done to AK8817VQ. "L "(GND level): Power-down "H ": normal operation Reset input pin. In order to initialize the device , an initialization must be made in accordance with the reset sequence. "L " : reset "H " : normal operation Hi-Z input is acceptable to this pin at PDN = L. 38 PDN I 39 RSTN I 40 DVSS G Digital ground pin (digital core ground). 41 DVDD P Digital power supply pin (digital core power supply). 42 N.C. - For normal operation, left open. 43 VOUT O Video output pin. 44 BVSS G Substrate ground pin. Connect this pin to Analog ground 45 SAG O SAG Compensation Input pin 46 AVSS G Analog ground pin. 47 DACOUT O 48 N.C. - For normal operation, left open. MODE / PIN name IREF VREF DACOUT VOUT PDNL PDN=HDAC=L VIDEOAMP=L PDN=HDAC=H VIDEOAMP=L PDN=HDAC=H VIDEOAMP=H Hi-Z Hi-Z Output Outpu Hi-Z Hi-Z DAC Power Down Hi-Z Hi-Z VIDEOAMP Power Down Output Output Output VIDEOAMP Power Down(1) Output Output Output Output DAC output pin. Connect this pin to Analog ground via a 390 ohm resistor ( better than +/- 1% accuracy ). Analog Output pin status DAC: Sub Address 0x00 bit7 0: L->DACOFF 1: H->DACON VIDEOAMP: Sub Address 0x01 bit3,4 00: L->VIDEOAMP_OFF 01,10: H-> VIDEOAMP_ON Note1) Video Amp becomes power down. Since DACOUT pin and VOUT pin are connected with RESISTOR in the LSI, DACOUT pin are not Hi-Z. In case of using only DAC, VOUT pin and SAG pin should be open states. MS1113-E-00 2009/08 -5- [AK8817VQ] Electrical Characteristics (1) Absolute Maximum Ratings Parameter Supply voltage DVDD, AVDD, PVDD Min Max Units -0.3 4.5 V Digital Input pin voltage (VinP) -0.3 PVDD +0.3 V Input pin current (Iin) -10 10 mA Note D[7:0], HDI, VDI, RSTN, PDN, CLKIN, CLKINV,SCL, SDA Exclude Power supply pin. -40 Storage temperature 125 C (Note1) Power supply voltages are values where each ground pin ( DVSS = AVSS = PVSS ) is at 0 V( voltage reference ). All power supply ground pins DVSS, AVSS and PVSS should be at same potential. (2) Recommended Operating Conditions Parameter Min Typ. Max Units Conditions Supply voltage * 3.3 3.6 V AVDD = DVDD 2.7 AVDD,DVDD Interface power supply 1.6 1.8 DVDD V PVDD Operating temperature -40 105 C (Ta) * Power supply voltages are values where each ground pin ( PVSS = AVSS = PVSS ) is at 0 V( voltage reference ). All power supply ground pins DVSS, AVSS and PVSS should be at same potential. (3) DC Characteristics < Operating voltage: DVDD 2.7V~3.6V / PVDD 1.6 V~DVDD, loading condition 15 pF, temperature -40~+105C > Parameter Symbol Min Typ Max Units Conditions 2.7VPVDDDVDD 0.7PVDD 0.7PVDD V Digital input H voltage (VIH) 1.6VPVDD2.7V 0.8PVDD 0.8PVDD 2.7VPVDDDVDD 0.3PVDD V Digital input L voltage (VIL) 1.6VPVDD2.7V 0.2PVDD Digital input leak current I2C (SDA) L output IL +/-10 uA VOLC 0.4 V IOLC = 3mA ( Note ) Digital output pins refer to D[7:0], HDI, VDI, PDN, RSTN, SCL, SDA,CLKIN and CLKINV pin outputs in general term. MS1113-E-00 2009/08 -6- [AK8817VQ] (4) Analog Characteristics < AVDD = 3.3 V, temperature 25 C > Max Units bit +/- 2.0 LSB +/- 1.0 LSB 1.18 1.38 V Note1) 5.0 mV Note2) 5.0 6.0 7.0 dB Amp Input Level 1Vpp 2.0 Vpp Note3) 100kHz 5.5MHz Note4) -45 -51 dB 100kHz 5.5MHz Note4) 54 dB 100kHz - 5.5MHz LPF Ripple -1 +/- 0.5 +1 dB 0dB = 100kHz input 27MHz LPF Stop Band Level 20 30 dB 0dB = 100kHz input LPF Group Delay 10 100 ns |GD3MHz - GD6MHz| On-chip reference voltage (VREF) 1.17 1.23 1.30 V Reference voltage drift -50 ppm/C Note1) Values are when a 390 ohm output load, a 12k ohm IREF pin resistor and on-chip VREF are used. Full scale output current is calculated as Iout = full scale output voltage ( typ. 1.28 V ) / 390 ohm = typ. 3.28 mA. Note2) A voltage referenced to VSS when a decimal zero voltage is input to DAC. Note3) VOUT Output Level Output Load Resistor: 150ohm, Load Capacitor: 15pF Internal Color Bar output Note4) Output signal from DAC to which Input data corresponded 1Vpp. This signal is input to AMP. Load resistor is 150ohm and Load capacitor is 15pF as shown bellow figure at (5) Current Consumption. Parameter DAC resolution DAC integral non-linearity ( error ) DAC differential non-linearity ( error ) DAC output full scale voltage DAC output offset voltage Video Amp Output Gain Video Amp Full scale Level Video Amp THD Video Amp S/N Symbol Min 9 +/- 0.6 +/- 0.4 1.28 MS1113-E-00 Typ 2009/08 -7- [AK8817VQ] (5) Current consumption < Operating voltage : DVDD = AVDD = PVDD = 3.3 V, Ta = +25 C > Parameter Symbol Min Typ Max Units Total power consumption 29 38 mA Note1) Power-down current 1 10 30 uA Note2) Digital part operating current 1 15 mA Note3) Analog part operating current 1 14 mA Note4) Analog part operating current 2 5.5 mA Note5) Analog part operating current 3 0.8 mA Note6) Note1) operation at 27 MHz, NTSC mode on-chip 75% color bar output is enabled and Video Amp output is " on " ( no external output loads are connected , other than those recommended, connecting-components ). AK8817 1uF AK8817 75ohm SAG 100uF 75ohm SAG 47uF VOUT 15pF 75ohm 15pF VOUT 15pF 75ohm 15pF SAG Compensation OFF SAG Compensation ON Note2) measuring conditions : input / output settings after power-down sequence are, PDN pin is at GND level, CLKOUT and SDO output are at high level ( power supply voltage ) with no external connection, input voltage on those input pins is 1/2 level of power supply which are set to accept Hi-Z input at power-down, and TEST = ATPG = GND ( or left open ). Power supplies are AVDD = DVSS = PVDD. Each ground pin ( DVSS, AVSS, PVSS ) is always 0 V ( voltage reference ). Note3) Operation at 27 MHz, NTSC mode on-chip 75% color bar output is enabled. Note4) DAC ON, Video Amp On SAG Compensation On Note5) DAC ON, Video Amp Off (SAG Compensation Off) Note6) DAC Off, Video Amp Off (SAG Compensation Off) MS1113-E-00 2009/08 -8- [AK8817VQ] AC Timing < DVDD 2.7 V ~ 3.6 V / PVDD 1.6 V ~ DVDD, Ta at -40 ~ +105 C > loading condition : CL = 15 pF (1) CLK fCLKI tCLKIL 1/2 PVD D tCLKIH VIH CLKIN VIL Parameter Symbol Min. Typ. Max Unit 24.5454 CLKIN fCLKI MHz 27 29.50 CLK duty ratio pCLKID 40 CLK Accuracy 60 % 100 ppm Conditions PIXRT=1 NTSC PIXRT=0 NTSC/PA PIXRT=1 PAL tCLKIL, tCLKIH : minimum pulse width 12 nS ( tr/tf10%-90%Level Rising/Falling time 2nS) (2) Pixel Data Input Timing VIH CLKIN VIL tDH tDS D[7:0] HDI VDI CLKINV = Low Parameter Symbol Min. Typ. Max Unit Data Setup Time tDS 5 nsec Data Hold Time tDH 8 nsec Conditions When CLKINV = High, similar tDS and tDH are specified at the falling edge of CLKOUT. MS1113-E-00 2009/08 -9- [AK8817VQ] (3) HSYNC pulse width pHSW HSYNC Parameter HDI Pulse Width Symbol pHSW Min. Typ. 15 116 15 128 Max Unit Conditions NTSC (24.5454MHz) CLKs 27MHz PAL (29.50MHz) * typical values are calculated by converting the HSYNC pulse width of Analog Video specification into number of system clock pulses. 15 139 (4) Reset (4-1) Reset Timing RSTN pRES 1 2 99 100 CLKIN Parameter RSTN Pulse Width Symbol Min. pRES 100 MS1113-E-00 Typ. Max Unit CLKs 2009/08 -10- [AK8817VQ] (4-2) Power Down Sequence / Reset Sequence Before PDN setting ( PDN to low ), Reset must be enabled for a duration of longer-than-100 clock time. After PDN release ( PDN to high ), Reset must be enabled for 10 mS or longer till analog part reference voltage & current are stabilized. (CLKOUT=H) CLKIN sRES hRES RSTN VIH VIL VIH PDN GND Parameter RSTN Pulse Width Symbol Min. sRES 100 Typ. Max Unit CLKs Time from PDN to high to RSTN to hRES 10 msec high At power-down, all control signals must be surely connected to either the selected power supply or ground level, and not to VIH / VIL levels. (4-3) Power Down Sequence/Power up sequence AVDD/DVDD PVDD PDN RSTN VREF 10mS(min) Recover from Power Down state MS1113-E-00 2009/08 -11- [AK8817VQ] (4-4) Power On Reset After Power up, It is necessary to make reset sequence until Analog Reference voltage(VREF) becomes stable. PVDD/DVDD/AVDD should be power up at same time or 1st PVDD power up and AVDD/DVDD makes up. 2.7V AVDD DVDD 1.6V PVDD 0.8PVDD PDN RSTN 0.2PVDD VREF 10mS(min) item RESETN Pulse width Symbol pRES_PON Min 10 Typ Max Unit msec Note Remark: Reset sequence requires clock input. MS1113-E-00 2009/08 -12- [AK8817VQ] (5) I2C Bus Input/Output Timing < Ta = -40 ~ +105 C > tBUF tHD:STA tR tSU:STO tF VSDAH SDA VSDAL tF tR VSDAH SCL VSDAL tSU:STA tLOW (5-1) Timing 1 VSDAH: 0.8PVDD VSDAL : 0.2PVDD Parameter Symbol Min. tBUF 1.3 usec tHD:STA 0.6 usec Clock Pulse Low Time tLOW 1.3 usec Input Signal Rise Time tR 300 nsec Input Signal Fall Time tF 300 nsec Bus Free Time Hold Time (Start Condition) Max. Unit Setup Time(Start Condition) tSU:STA 0.6 usec Setup Time(Stop Condition) tSU:STO 0.6 usec The above I2C bus related timing is specified by the I2C Bus Specification, and it is not limited by the device performance. For details, please refer to the I2C Bus Specification. (5-2) Timing 2 tHD:DAT VSDAH VSDAL SDA tHIGH VSDAH VSDAL SCL tSU:DAT VSDAH: 0.8PVDD VSDAL : 0.2PVDD Parameter Symbol Min. Data Setup Time tSU:DAT 100 (note1) Data Hold Time tHD:DAT 0.0 tHIGH 0.6 Clock Pulse High Time Max. Unit nsec 0.9 (note2) usec usec note 1 : when to use I2C Bus Standard mode, tSU:DAT >- 250 ns must be met. note 2 : when the AK8817VQ is used in such bus interface where tLOW is not extended ( at minimum specification of tLOW ), this condition must be met. MS1113-E-00 2009/08 -13- [AK8817VQ] Device Control Interface The AK8817VQ is controlled via I2C Bus Control Interface. [ I2C SLAVE Address ] 2C Slave Address is 0x40 [ I2C Control Sequence ] (1) Write Sequence When the Slave Address of the AK8817VQ Write mode is received at the first byte, Sub Address at the second byte and Data at the third and succeeding bytes are received. There are 2 operations in Write Sequence - a sequence to write at every single byte, and a sequential write operation to write multiple bytes successively. (a) 1 Byte Write Sequence Slave S w A Address 8-bits 1bit Sub Address 8-bits A Data A 1bit 8-bits 1bit Stp (b) Multiple Bytes ( m-bytes ) Write Sequence ( Sequential Write Operation ) Sub Slave Data(n+ S w A Address Data(n) A A Address 1) (n) 8-bits 1bit 8-bits 1bit 8-bits 1bit 8-bits A .... Data(n+m) A 8-bits 1bit 1bit stp (2) Read Sequence When the Slave Address of the AK8817VQ Read mode is received, Data at the second and succeeding bytes are transmitted. S Slave Address 8-bits w A Sub Address (n) A 1 8-bits 1 rS Slave Address 8-bits R A Data1 A Data2 A Data3 A 1 8-bits 1 8-bits 1 8-bits 1 ... Data n 8-bits 1 stp Abbreviated terms listed above mean : S, rS A Astp R/W : Start Condition : Acknowledge ( SDA Low ) : Not Acknowledge ( SDA High ) : Stop Condition 1 : Read 0 : Write : to be controlled by the Master Device. Micro-computer interface is output normally . : to be controlled by the Slave Device. To be output by the AK8817VQ. MS1113-E-00 2009/08 -14- [AK8817VQ] Video Encoder Functional Outline (1) Reset (1-1) Reset of Serial Interface part ( asynchronous reset ) Reset is made by setting RSTN pin to low. (1-2) Reset of other than Serial Interface blocks Reset is made by keeping RSTN pin low for a longer than 100 clock time, in normal operation. (1-3) at Power-On-Reset ( including power-down release case ) Follow the power-on-reset sequence. At the completion of each initialization, all internal registers are set to default values ( refer to Register Map ). Right after the reset, Video output of the AK8817VQ is put into Hi-Z condition. (2) Power-Down It is possible to put the device into power-down mode by setting the AK8817VQ power-down pin to GND. Transition to power-down mode should be followed by the power-down sequence. As for the recover from the power-down mode, it should be followed by the power-down release sequence. (3) Master Clock A following clock should be input as a Master clock. In Encoder Mode operation ( a synchronized clock with input data is required ) When ITU-R BT.601 data is input When Square Pixel data is input ( PIXRT-bit = 0 ) ( PIXRT-bit = 1 ) NTSC Encoder 27MHz 24.5454MHz PAL Encoder 27MHz 29.50MHz (4) Video Signal Interface Video input signal ( data ) should be synchronized in either of the following methods : * Slave mode operation where synchronization is made with HSYNC ( HDI ) / VSYNC ( VDI ). * ITU-R BT. 656 I / F ( EAV decode ) (only 27MHz operation) (5) Pixel Data Input data to the AK8817VQ is YCbCr ( 4:2:2 ). Data with Y : 16 ~ 235 and CbCr : 16 ~ 240 should be input. (6) Video Signal Conversion Video Re-Composition module converts the multiplexed data ( ITU-R BT.601 Level Y, Cb, Cr ) into interlaced NTSC-M and PAL-B, D, G, H, I data. Video encoding setting is done by "Control 1 Register ". MS1113-E-00 2009/08 -15- [AK8817VQ] (7) Luminance Signal Filter ( Luma Filter ) Luminance signal is output via LPF ( see x2 Luma Filter in the block diagram ). 10 0 0.0 1.0 2.0 Gain[dB] -10 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 -20 -30 -40 -50 frequency[MHz] (8) Chroma Signal Filter ( Chroma Filter ) Chroma input signal components ( Cb, Cr ) prior to the modulation go through a 1.3 MHz Band Limiting Filter ( see 4:2:2 to 4:4:4 x2 interpolator in the block diagram ). Chroma signal which is modulated by the sub-carrier is output via a low pass filter ( Chroma LPF in the block diagram ). Frequency response of each filter is shown below. 4:2:2 to 4:4:4 Interpolator Filter 10 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Gain[dB] -10 -20 -30 -40 -50 Frequency[MHz] x 2 Interpolator Filter 10 0 Gain[dB] -10 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 -20 -30 -40 -50 frequency[MHz] MS1113-E-00 2009/08 -16- [AK8817VQ] (9) Color Burst Signal Burst signal is generated by a 32 bit digital frequency synthesizer. Color Burst Frequency is selected by mode setting of NTSC / PAL. NTSC-M Subcarrier Freq (MHz) 3.57954545 PAL-B,D,G,H,I 4.43361875 Standerd Video Process 1 VMOD-bit 0 1 Burst Signal Table (10) Sub - Carrier Reset A function to reset sub-carrier by Color Frame sequence. Reset function can be turned "OFF " by setting SCR-bit of Control 1 Register. Default value is set to enable Sub-carrier reset. SCR NTSC PAL 0 1 Sub-carrier phase is reset in every 2 Frames ( 4 Fields ) Sub-carrier phase is reset inevery 4 Frames ( 8 Fields ) Sub-carrier reset is not done Sub-carrier reset is not done (11) Setup processing Setup processing can be performed on Video signal by Control 2 Register Setup-bit. Following processing is made on Luminance signal ( Y signal ) and Chroma signal ( C signal ) by the Setup processing. Y Setup = Y x 0.925 + 7.5 IRE where Y setup is the Luminance signal after Setup processing. C Setup = C x 0.925 where C Setup is the Chroma signal after Setup processing. (12) Video DAC The AK8817VQ has a 9 Bit resolution, current-drive DAC as a video DAC which runs at 29.5 / 24.5454 MHz or 27.00MHz clock frequency. This DAC is designed to output 1.28 V o-p at full scale under the following conditions loading resistance of 390 ohms, VREF at 1.23 V and IREF pin resistor of 12k ohms. [ VREF ] pin should be connected to ground via a 0.1 uF or larger capacitor. DAC output can be turned "ON" or "OFF" by register setting and current consumption can be lowered. When the output is turned off, it is put into high impedance condition. MS1113-E-00 2009/08 -17- [AK8817VQ] (13) Video Amp AK8817VQ has Video amp that can drive 150ohm with Low pass filter. It can also possible to compensate SAG distortion. To compensate SAG external capacitor is 47uF and 1uF as shown following figure. Recommendation voltage when SAG compensation circuit is used is 3V or more. VOUT pin and SAG pin should be shorten when SAG Compensation is not used. Output pin should make AC coupling. SAG Compensation circuit can be set on or off with setting register. In case of not using internal Video amp (Only DAC use case), Video Amp becomes power down. In this case SAG and VOUT should be Open. AK8817 1uF AK8817 75ohm SAG 100uF 75ohm SAG VOUT VOUT 47uF SAG Compensation ON SAG Compensation Off VAMPMD[1:0] 00 Operation Video Amp OFF + SAG Compensation OFF 01 Video AMP ON + SAG Compensation ON 10 Video Amp ON + No SAG Compensation 11 Reserved MS1113-E-00 Conditions Only DAC output Recommendation Voltage of DVDD/AVDD is 3v or more. SAG pin and VOUT should be shorten. 2009/08 -18- [AK8817VQ] (14) Video Data Interface Timing Data is captured by a clock which is fed on CLKIN pin. The Video Encoder receives a clock from a controller ( refer to the following diagram ). In Slave mode operation, Synchronization is made with HDI / VDI. In ITU-R BT.656 mode operation, HDI / VDI are not required. C L K IN (H D I) C o n t r o lle r (V D I) AK8817 D [7 :0 ] MS1113-E-00 2009/08 -19- [AK8817VQ] (14-2) Video Interface mode The AK8817VQ synchronizes with input signal by the following, 2 interface modes. (a) Slave-mode interface where synchronization is made with externally-fed synchronization signals HDI / VDI ( HDI / VDI interface ) (b) ITU-R BT.656 Interface mode ( 656 interface ) interface mode setting is controlled by [REC656]-bit of Control 2 Register. REC656-bit 0 1 Operation HDI / VDI Slave mode ITU-R BT.656 Interface mode (a-1) Timing signal ( HDI / VDI ) VS Data input relation Horizontal Synchronization ( in-line Pixel Sync ) is made with HDI synchronization timing signal. Vertical Synchronization ( in-line Frame Line Sync ) is made with VDI synchronization timing signal. Recognition of Video Field ( Odd Field or Even Field ) is made by VDI input signal which is referenced with HDI. In normal operation, the AK8817VQ checks changes of HDI and VDI at the clock edge ( CLK synchronization ) which becomes a data capture reference position. At a pixel position where HDI is judged to become " Low ", it is recognized as 0H (zero th position ). Cb0 data position depends on input data rate ( ITU-R BT.601 or Square Pixel data ). Cb0 Data NTSC Encoder PAL Encoder At ITU-R BT.601 Data input 244th data 264th data At Square Pixel data input 236th data 310th data Video Field is recognized by the VDI relation with HDI. Field recognition is made as follows : The AK8817VQ distinguishes at every Field if it is Odd Field ( 1st Field ) or not. Even Field Sync signal is not usually input. 1 ) Recognition timing of Odd Field is decided by those timing signal relations which are fed on HDI and VDI pins. When the VDI falling pulse is input on VDI input pin during the time from 3 clocks prior to the falling edge of HDI timing pulse which is fed on HDI input till 3 clocks prior to the rising edge of HDI timing pulse, the Line is recognized to be Line 4. Line4/Line1(NTSC/PAL) Line5/Line2(NTSC/PAL) Line6/Line3(NTSC/PAL) HDI 3CLK VDI 3CLK 2 ) Whenever Horizontal / Vertical SYNC signal inputs are not fed as expected in the Video Specifications, in term of timing and # of pulses ( kept at " High " level ), the AK8817VQ continues to self-run the operation which is based on the Sync signals, fed just before. But it is recommended to feed Sync signals as specified every time in order to prevent erroneous operation. 3 ) VD pulse input at other than Odd Field synchronization is ignored ( Synchronization is made with Odd Field only ). MS1113-E-00 2009/08 -20- [AK8817VQ] (a-2) Horizontal Synchronization ( Pixel Data synchronization within a Line ) (a-2-1) at ITU-R BT. 601 data input case (a-2-1-1) NTSC 1715 0 244 245 246 247 248 (0x10) (0x80) (0x10) (0x80) (0x10) Cb0 Y0 Cr0 Y1 Cb1 1683 1684 1713 1714 CLKIN (27.00MHz) DTI[7:0] Cr359 Y719 (0x80) (0x10) (0x10) (0x80) 0H HDI Active Video Area 244T 720 x 2 Clock * ) when D [7:0], HDI and CLKIN are in same phase relation as a timing example above, the AK8817VQ takes input data at the falling edge of each CLKIN if CLKEDGE-bit = 1.(CLKINV = 1.) * ) as an input data other than during active video period, Black level ( C / Y = 0x80 / 0x10 ) or other than 0x00 / 0xFF codes in non Hi-Z state should be input. (a-2-1-2) PAL 1727 0 264 265 266 267 268 (0x10) (0x80) (0x10) (0x80) (0x10) Cb0 Y0 Cr0 Y1 Cb1 1702 1703 1704 1725 1726 CLKIN (27.00MHz) DTI[7:0] Cr359 Y719 (0x80) (0x10) (0x10) (0x80) H0 HDI Active Video Area 264T 720 x 2 Clock *) when D [7:0], HDI and CLKIN are in same phase relation as a timing example above, the AK8817VQ takes input data at the falling edge of each CLKIN if CLKEDGE-bit = 1. .( CLKINV = 1.) * ) as an input data other than during active video period, Black level ( C / Y = 0x80 / 0x10 ) or other than 0x00 / 0xFF codes in non Hi-Z state should be input. MS1113-E-00 2009/08 -21- [AK8817VQ] (a-2-2) at Square Pixel Rate input case (a-2-2-1) NTSC 1559 0 TBD 236 237 238 239 240 Y0 Cr0 Y1 Cb1 1514 1515 1516 CLKIN (24.5454MHz) (0x10) (0x80) (0x10) (0x80) (0x10) Cb0 D[7:0] Cr319 Y639 (0x80) (0x10) H0 HDI Active Video Area 640 x 2 Clock * ) when D [7:0], HDI and CLKIN are in same phase relation as a timing example above, the AK8817VQ takes input data at the falling edge of each CLKIN if CLKINV = 1. * ) as an input data other than during active video period, Black level ( C / Y = 0x80 / 0x10 ) or other than 0x00 / 0xFF codes in non Hi-Z state should be input. (a-2-2-2) PAL 1887 0 TBD 310 311 312 313 314 Cb0 Y0 Cr0 Y1 Cb1 1844 1845 1846 CLKIN (29.5MHz) D[7:0] (0x10) (0x80) (0x10) (0x80) (0x10) Cr383 Y767 (0x80) (0x10) H0 HDI Active Video Area 768 x 2 Clock * ) when D [7:0], HDI and CLKIN are in same phase relation as a timing example above, the AK8817VQ takes input data at the falling edge of each CLKIN if CLKINV-bit = 1. .(CLKINV = 1.) * ) as an input data other than during active video period, Black level ( C / Y = 0x80 / 0x10 ) or other than 0x00 / 0xFF codes in non Hi-Z state should be input. MS1113-E-00 2009/08 -22- [AK8817VQ] ( a-3 ) HDI and VDI relation in each Frame ( a-3-1 ) NTSC ( Frame ) 525 Line 480 active lines The First Field ( ODD ) 263 lines 240 lines 525 1 2 3 4 5 6 7 22 23 261 262 263 264 525 1 2 HDI VDI * )VDI negative-going should be fed during the time from 3 clocks prior to negative-going of HDI at L4 till 3 clocks prior to positive-going of HDI. VDI positive-going can occurs at arbitrary location, but keep VDI low for 3 line duration time as a rough idea. The Second Field ( EVEN ) 262 lines 240 lines 263 264 265 266 267 268 269 270 285 286 524 HDI VDI High * ) VDI negative-going is not required for the Second Field. It is required for the First Field only ( VDI fed during the Second Field is ignored ). MS1113-E-00 2009/08 -23- [AK8817VQ] ( a-3-2 ) PAL ( Frame ) 625 Line 576 active lines The First Field ( ODD ) 313lines 288lines 625 1 2 3 4 5 22 23 24 310 311 312 313 314 HDI VDI * ) VDI negative-going should be fed during the time from 3 clocks prior to negative-going of HDI at L1 till 3 clocks prior to positive-going of HDI. VDI positive-going can occur at arbitrary location, but as a rough idea, keep VDI low for 2.5, or 2 or 3 line- duration time. Data fed at Line 23 is not output on Video output The Second Field (EVEN) 313lines 288lines 313 314 315 316 317 318 335 336 337 623 624 625 1 2 HDI VDI High *) VDI negative-going is not required for the Second Field. It is required for the First Field only ( VDI fed during the Second Field is ignored ). Data fed at Line 623 is not output. MS1113-E-00 2009/08 -24- [AK8817VQ] ( b-1 ) ITU-R BT.656 Interface mode The AK8817VQ makes a synchronization with an incoming signal by decoding EAV in the signal when ITU-R BT.656 encoded signal is input. EAV code is located at the following position in the Video stream ( this mode of operation is not supported in the Square Pixel clock operation ). Y/Cb/Cr Data# 525system Data# 625system Cb EAV Y Cr Y Cb Y Cr Y Cb Y Cr Y Cb SAV Y Cr Y Cb Y Cr Y Cb 360 720 360 721 361 722 361 723 368 736 368 855 428 856 428 857 0 0 0 1 1 360 720 360 721 361 722 361 723 366 732 366 861 431 862 431 863 0 0 0 1 1 CLKIN 33/ 25T(525/ 625) 243/ 263T(525/ 625) 276/ 288T(525/ 625) HDI MS1113-E-00 2009/08 -25- [AK8817VQ] ( 1 ) EAV Synchronization an EAV code which is encoded on input signal is decoded, and the device makes synchronization with its timing. EAV / SAV codes are as follows. Those codes succeeding 0xFF- 0x00- 0x00 which are fed as input data in 8-bit form become EAV / SAV codes. EAV / SAV codes have following meanings, starting with MSB. Bit Number WORD VALUE 0 0xFF 1 0x00 2 0x00 3 0xxx MSB 7 1 0 0 1 6 1 0 0 F 5 1 0 0 V 4 1 0 0 H 3 1 0 0 P3 2 1 0 0 P2 LSB 0 1 0 0 P0 1 1 0 0 P1 here, F = 0 : Field 1 = 1 : Field 2 V = 0 : other than Filed Blanking (V-Blanking) = 1 : Filed Blanking (V-Blanking) H = 0 : SAV = 1 : EAV P3, P2, P1, P0 : Protection Bit Protection Bit and F / V / H relation is shown in the following table. F V H P3 0 0 0 0 0 0 1 1 0 1 0 1 0 1 1 0 1 0 0 0 1 0 1 1 1 1 0 1 1 1 1 0 P2 0 1 0 1 1 0 1 0 P1 0 0 1 1 1 1 0 0 P0 0 1 1 0 1 0 0 1 At NTSC data input case Cb Y Cr Y 359 718 359 719 Cb 360 Y Cr 720 360 EAV Y 721 ...... Cb 428 Y Cr 856 428 SAV Y 857 Cb 0 Y 0 Cr 0 Y 1 At PAL data input case Cb Y Cr Y 359 718 359 719 Cb 360 Y Cr 720 360 EAV Y 721 ...... Cb 431 Y Cr 862 431 SAV Y 863 Cb 0 Y 0 Cr 0 Y 1 MS1113-E-00 2009/08 -26- [AK8817VQ] ( 1-1 ) EAV / SAV Code and Line Synchronization The AK8817VQ makes Vertical synchronization ( Line synchronization ) when F-bit in EAV makes transition from " 1 " to " 0 ". F-bit of EAV / SAV and Line relation is as follows F-bit NTSC PAL 0 Line4 - Line265 Line1 - Line312 Line266 - Line525 1 Line313 - Line625 Line1 - Line3 For reference, V-bit of EAV / SAV and Line relation is also shown below. Field V-bit NTSC PAL Start (V=1) Line1 - Line19 Line624 - Line625 - Line22 Field 1 End (V=0) Line20 - Line263 Line23 - Line310 Start (V=1) Line264 - Line282 Line311 - Line335 Field 2 End (V=0) Line283 - Line525 Line336 - Line623 Digital Line-No. 1 2 3 4 5 7 8 9 synchronization is made at this timing F-bit Digital Line-No. 6 263 264 265 266 267 268 269 270 271 272 F-bit Line Synchronization by EAV at NTSC input case Digital Line-No. 622 623 624 625 1 3 4 5 6 synchronization is made at this timing F-bit Digital Line-No. 2 310 311 312 313 314 315 316 317 318 319 F-bit Line Synchronization by EAV at PAL input MS1113-E-00 2009/08 -27- [AK8817VQ] (15) On-chip Color Bar The AK8817VQ can output Color Bar signal. Color Bar signal to be generated has 100 % amplitude and 75 % Saturation levels. Color Bar signal is output by setting register. When to output Color Bar signal, there are 2 modes of operation - one is external Sync timing mode for normal operation, and the other is internal self-operation mode. In internal self-operating mode, required timing is internally generated automatically. Namely, it is no need to input synchronization timing from outside of the chip. Operation mode setting is done by Control 1 Register . When BBG-bit is set, BBG-bit is prioritized ( Black Burst is output ). BLACK BLUE RED MAGENTA GREEN CYAN YELLOW WHITE 100%White Synctip Level Cb Y Cr WHITE 128 235 128 YELLOW 44 162 142 CYAN 156 131 44 GREEN 72 112 58 Blanking Level The following values are code for ITU-R. BT601 MAGENTA RED BLUE BLACK 184 100 212 128 84 65 35 16 198 212 114 128 (16) Black Burst Signal generation function The AK8817VQ can output Black Burst signal ( Black level output ). When to output Black Burst signal, there are 2 modes of operation - one is external Sync timing mode for normal operation , and the other is internal self-operation mode. In internal self-operation mode, required timing is internally generated automatically. Namely, it is no need to input synchronization timing from outside of the chip. When BBG-bit of [ Control 1 Register ] is set to "1", same operation is processed as in the case where fixed-16 Y signal and fixed-128 Cb / Cr signal outputs are input. Operation mode setting is done by Control 1 Register setting. MS1113-E-00 2009/08 -28- [AK8817VQ] (17) Video ID The AK8817VQ supports to encode the Video ID ( EIAJ CPR-1204 ) which distinguishes the aspect ratio etc.. This is also used as CGMS ( Copy Generation Management System ). Turning "ON/OFF" of this function is made by setting both VMOD-bit = 0 and VBID-bit = 1 of { Control 1 Register (0x00) }. And data to be set is written into { VBID / WSS Data1 & 2 Registers ( 0x02,0x03 )}. Video ID information is the highest order of priority information among VBI information VBID Data Update timing . VSYNC S et C ontro l R egister u-P D a ta N EW D AT A DATA O LD D A T A N EW D AT A VBID Code assignment 20 bit data is configured with WORD0 = 2 bit, WORD1 = 4 bit, WORD2 = 8 bit and CRC = 6 bit. CRC is automatically calculated and added by the AK8817VQ. Default values of CRC polynomial expression X6 + X + 1 are all ones. -data configuration bit1 bit20 DATA WORD0 2bit WORD1 4bit WORD2 8bit CRC 6bit VBID Waveform Ref. bit1 bit2 bit3 *** bit20 70IRE +/- 10IRE 0IRE + 10 IRE - 5 IRE 2.235usec +/- 50nsec 11.2usec +/- 0.3usec 49.1usec +/- 0.44usec 1H 525/60 System 70IRE 20/283 Amplitude Encode Line MS1113-E-00 2009/08 -29- [AK8817VQ] ( 17 ) WSS function The AK8817VQ supports to encode the WSS ( ITU-R. BT.1119 ) which distinguishes the aspect ratio and sets CGMS-A etc.. Turning "ON/OFF" of this function is made by setting both VMOD-bit = 1 and WSS-bit = 1 of { Control 1 Register ( 0x00 ) }. And data to be set is written into { VBID / WSS Data1 & 2 Registers ( 0x02, 0x03 )}. WSS Data Update timing VSYNC S et C ontro l R egister u-P D a ta N EW D AT A DATA O LD D A T A N EW D AT A WSS Waveform 500mV +/- 5% 0H 27.4usec 1.5usec 10.5usec 11.0 +/- 0.25usec 38.4usec 44.5usec Encode line : former half of Line 23 ( Blank output during latter half ) Coding : Bi-phase modulation coding Clock : 5 MHz ( Ts = 200 nS ) Encoding details as follows Run-in Start code 29 elements 24 elements 0x1F1C71C7 0x1E3C1F Group 1 Aspect ratio 24 elements Bit numbering 0 1 2 3 LSB MSB 0 : 000111 1 : 111000 MS1113-E-00 Group 2 Enhanced Services 24 elements Bit numbering 4 5 6 7 LSB MSB 0 : 000111 1 : 111000 Group 3 Subtitles 18 elements Bit numbering 8 9 10 LSB MSB 0 : 000111 1 : 111000 Group4 Reserved 18 elements Bit numbering 11 12 13 LSB MSB 0 : 000111 1 : 111000 2009/08 -30- [AK8817VQ] SYNC Signal waveform, Burst Waveform generator (1) NTSC-J S y n c r is e t im e 50% B u r s t H e ig h t 90% B u rs t H o r iz o n ta l r e f e r e n c e p o in t 50% 50% S ync Le ve l 10% S yn c H . r e f . t o B u r s t S ta r t measurement point Total line period(derived) Sync Level Sync rise time Horizontal Sync width Horizontal reference point to burst start Burst * Burst Height ** value Consumer Quality tolerance units 10% - 90% 50% 63.556 40 140 4.7 +/- 3 Max 250 +/- 0.1 usec IRE nsec usec 50% 19 defined by SC/H cycles 50% 9 40 +/- 1 +/- 3 cycles IRE * there is a case where tolerance of Sync rise time is added to Sync width tolerance. * Measurement of Burst time length is made between the Burst start point which is defined as the zero-cross point, preceding the first half-cycle of the sub-carrier where Burst amplitude becomes higher than 50 % level and the Burst end point, defined in the same manner. 19 cycles +/-10 9 cycles +/- 1cycle 50% NTSC Signal MS1113-E-00 2009/08 -31- [AK8817VQ] (2) Vertical Sync Signal timing ( NTSC ) 3H 3H 3H 0 .5 H 525 1 2 3 4 5 3H 6 7 8 3H 9 21 3H 0 .5 H 2 62 263 264 265 266 2 67 26 8 269 270 271 G I 272 2 73 285 H I I I 40IRE +/-3IRE Equalizing Pulse Serration Pulse Equalizing Pulse and Serration Pulse Symbol G H G I Pre-equalizing pulse width Vertical serration pulse width Post-equalizing pulse width Sync rise time Measurement point 50% 50% 50% Value 2.3 4.7 2.3 140 Recommended tolerance +/- 0.1 +/- 0.2 +/- 0.1 Max 250 units usec usec usec nsec * there is a case where tolerance of Sync rise time is added to Pulse width tolerance. MS1113-E-00 2009/08 -32- [AK8817VQ] (3) PAL-B,D,G,H,I S y n c r is e t im e 50% B u r s t H e ig h t 90% B u rs t H o r iz o n ta l r e f e r e n c e p o in t 50% 50% S yn c L e ve l 10% H o r iz o n ta l S y n c H . r e f . t o B u r s t S ta r t measurement point Total line period(derived) Sync Level Sync rise time Horizontal Sync width Horizontal reference point to burst start Burst * Burst Height ** value Consumer Quality tolerance units 10% - 90% 50% 64.0 300 0.2 4.7 +/- 20 Max 0.3 +/- 0.2 usec mV usec usec 50% 5.6 +/- 0.1 usec 50% 10 300 +/- 1 +/- 30 cycles mV * there is case where tolerance of Sync rise time is added to Sync width tolerance. MS1113-E-00 2009/08 -33- [AK8817VQ] (4) Vertical Sync Signal timing and Burst Phase PAL-B,D,G,H,I A 308 620 309 621 308 620 310 622 309 311 623 310 621 622 312 624 311 623 313 625 312 624 314 1 313 625 315 2 314 1 316 3 315 2 317 4 316 3 318 5 317 4 319 320 A B 6 7 A B 318 319 A B 5 B 7 322 321 322 8 320 6 321 8 A : Phase of Burst : nominal Value + 135 B : Phase of Burst : nominal Value - 135 Since Burst frequency and Line frequency are not practically in integer-multiple relation, specified phase value is not exactly 135 degrees. Diagram below shows phase direction. G I H I I I 300mV +/-30mV Equalizing Pulse Serration Pulse Equalizing Pulse and Serration Pulse Symbol G H G I Pre-equalizing pulse width Vertical serration pulse width Post-equalizing pulse width Sync rise time Measurement point 50% 50% 50% Value 2.35 4.7 2.35 200 Recommended tolerance +/- 0.1 +/- 0.2 +/- 0.1 Max 300 units usec usec usec nsec * there is a case where tolerance of Sync rise time is added to Pulse width tolerance. MS1113-E-00 2009/08 -34- [AK8817VQ] Register Map Address 0x00 0x01 0x02 0x03 Register Control 1 Register Control 2 Register VBID/WSS Data 1 Register VBID/WSS Data 2 Register Default 0x00 0x00 0x00 0x00 R/W R/W R/W R/W R/W 0x04 Input Control Register 0x00 R/W 0x05 Device ID & Revision ID Register 0x17 R MS1113-E-00 Function Mode set Register Mode set Register VBID data is set, WSS data is set VBID data is set, WSS data is set Input control register for out-of-standard quality input signal Register for Device ID and Revision ID 2009/08 -35- [AK8817VQ] Control 1 Register (R/W) [Address 0x00] Sub Address 0x00 bit 7 bit 6 DAC BBG 0 bit 5 CBG 0 0 Control 1 Register Definition BIT Register Name bit 0 VMOD bit 1 bit 4 bit 3 MASMD WSS Default Value 0 0 R/W Video Mode bit R/W SCR Sub-Carrier Reset bit R/W bit 2 VBID VBID Set bit R/W bit 3 WSS WSS Set bit R/W bit 4 MASMD Master Mode bit R/W bit 5 CBG Color Bar Generator bit R/W bit 6 BBG Black Burst Generator bit R/W bit 7 DAC DAC Set bit R/W bit 2 VBID bit 1 SCR 0 0 Default Value 0x00 bit 0 VMOD 0 Definition 0: NTSC 1: PAL 0 : Sub-Carrier Reset 1 : Sub-Carrier Reset off 0 : VBID OFF 1 : VBID ON 0 : WSS OFF 1 : WSS ON Master Mode bit to set Sync mode when Color Bar signal and Black Burst signal are generated 0 : operation by an external Sync timing 1 : operation by an internal self-operating mode ( master mode ) note ) Master mode bit is still valid in normal data input, but output video is not synchronized. 0: OFF 1: ON when BBG is set, BBG is prioritized. 0 : OFF 1 : ON 0 : DAC OFF 1 : DAC ON MS1113-E-00 2009/08 -36- [AK8817VQ] Control 2 Register (R/W) [Address 0x01] Sub Address 0x01 bit 7 bit 6 Reserved Reserved 0 bit 5 Reserved 0 0 bit 4 bit 3 VAMPMD1 VAMPMD0 Default Value 0 0 Control 2 Register Definition BIT Register Name bit 0 PIXRT bit 1 R/W Pixel Rate Set bit R/W REC656 Rec656 Set bit R/W bit 2 SETUP Setup bit R/W bit 3 ~ bit 4 VAMPMD0 ~ VAMPMD1 VIdeo Amp Mode Set bit R/W bit 5 ~ bit 7 Reserved Reserved bit R/W bit 2 SETUP 0 Default Value 0x00 bit 1 bit 0 REC656 PIXRT 0 0 Definition Pixel rate setting is done. 0 : ITU-R BT.601 data input ( at 27 MHz rate ) 1 : Square Pixel data input NTSC : 24.5454 MHz PAL : 29.50 MHz Synchronization mode setting is done. 0 : synchronization is made with HDI / VDI input. 1 : synchronization is made with ITU-R BT.656 data input Set-up setting is done 0 : with no set-up 1 : with 7.5 IRE set-up Operation mode for Video Amp. VAMPMD[1:0] 00: Video Amp OFF + SAG Compensation OFF 01: Video AMP ON + SAG Compensation ON 10: Video Amp ON + No SAG Compensation 11: Reserved Set "0" MS1113-E-00 2009/08 -37- [AK8817VQ] VBID/WSS 1 Register (R/W) [Address 0x02] VBID/WSS 2 Register (R/W) [Address 0x03] Video ID and WSS data setting are made. A common data register is used for both video ID and WSS data. When VBID bit of mode register is set in NTSC mode, data is for VBID data ,and when WSS bit of Control 1 Register is set in PAL mode, data is for WSS data. When VBID-bit is "1" and VMOD-bit is "0" in Control 1 Register , the following bits are assigned. Sub Address 0x02 bit 7 bit 6 VBID7 VBID8 0 0 Sub Address 0x03 bit 7 bit 6 Reserved Reserved 0 0 bit 5 VBID9 0 bit 5 VBID1 0 default Value 0x00 bit 1 bit 0 VBID13 VBID14 bit 4 bit 3 VBID10 VBID11 Default Value 0 0 bit 2 VBID12 0 0 bit 4 bit 3 VBID2 VBID3 Default Value 0 0 bit 2 VBID4 bit 1 VBID5 0 0 0 default Value 0x00 bit 0 VBID6 0 Note ) "0" should be written into reserved bits. VBID1 ---- VBID14 above correspond to the bit 1 ---- bit 14 which are described at { VBID Data Code Assignment } in { ( 14 ) Video ID } section. A 6-bit CRC code from bit 15 ~ bit 20 is automatically added by the AK8817VQ. Data is retained till data is updated to a new one. Following bits are assigned when WSS-bit is "1" and VMOD-bit is "1" in Control 1 Register . Sub Address 0x02 bit 7 bit 6 G2-7 G2-6 0 0 Sub Address 0x03 bit 7 bit 6 Reserved Reserved 0 0 bit 5 G2-5 0 bit 5 G4-13 0 bit 4 bit 3 G2-4 G1-3 Default Value 0 0 bit 2 G1-2 bit 1 G1-1 0 0 bit 4 bit 3 G412 G4-11 Default Value 0 0 bit 2 G3-10 bit 1 G3-9 0 0 default Value 0x00 bit 0 G1-0 0 default Value 0x00 bit 0 G3-8 0 Note ) WSS data is written with 0x01 first, then 0x02 in this order. When the 2nd byte ( 0x02 ) of WSS data is written, the AK8817VQ interprets that data is updated to a new one and then encodes it to the next video line ( Line 23 ). Data is retained till data is updated to a new one. MS1113-E-00 2009/08 -38- [AK8817VQ] Input Control Register (R/W) [Address 0x04] This is an out-of-standard quality input signal control register. Sub Address 0x04 bit 7 bit 6 Reserved CBCR 0 0 bit 5 VD2 0 Adjustment of Sync input timing is made. BIT Register Name HD0 bit 0 ~ HDI Input Delay ~ HD2 bit 2 VD0 bit 3 ~ VDI Input Delay ~ VD2 bit 5 bit 6 CBCR Exchange CbCr bit 7 Reserved Reserved bit 4 VD1 0 bit 3 VD0 0 R/W bit 2 HD2 0 default Value 0x00 bit 1 bit 0 HD1 HD0 0 0 Definition R/W HDI signal input is delayed by the set value. HD [ 2:0 ] system clock count delay ( + 0 ~ + 7 CLK delay ) R/W VDI signal input is delayed by the set value. VD [ 2:0 ] system clock count delay ( + 0 ~ + 7 CLK delay ) R/W R/W Cb, Cr timing data are interchanged at CBCR = 1. Reserved MS1113-E-00 2009/08 -39- [AK8817VQ] Device ID and Revision ID Register (R) [Address 0x05] Register to show Device ID & Revision of the AK8817VQ. Device ID for AK8817VQ is 0x17(decimal) Initial Version of the Revision ID is 0x00. Revision number is modified only when a control software needs to be modified. Sub Address 0x5 bit 7 bit 6 Rev1 REV0 0 0 bit 5 DEV5 0 Device ID and Revision ID Register Definition BIT Register Name DEV0 bit 0 ~ Device ID bit ~ DEV2 bit 5 bit 6 ~ bit 7 REV0 ~ REV2 Revision ID bit bit 4 DEV4 1 R/W bit 3 DEV3 0 bit 2 DEV2 1 bit 1 DEV1 1 default Value 0x17 bit 0 DEV0 1 Definition R To show Device ID Device ID is 0x17h. R To show Revision information Revision ID is updated when software modification is to be expected. It is 0x00. MS1113-E-00 2009/08 -40- [AK8817VQ] System Connection Example AK8817VQ HSYNC VSYNC D[7:0] PVDD PVDD SAG PVSS HDI VDI VOUT 75 ohm 47uF CLKIN Clock 1uF DACOUT u-P I2C SDA 390ohm SCL RSTN PDN VREF Digital 3.0V 0.1uF DVDD DVSS TEST IREF ATPG 12kohm CLKINV AVSS AVDD Analog 3.0V 0.1uF DVSS 10uF AVSS MS1113-E-00 2009/08 -41- [AK8817VQ] Package Drawing 48pin LQFP 9.000.20 7.00 25 37 24 48 13 7.00 9.000.20 36 12 1 0.50 0.10 0 10 M 0.500.20 0.10 MS1113-E-00 S 1.60MAX 1.4TYP 1.00 S 0.100.07 0.170.05 0.190.05 2009/08 -42- [AK8817VQ] Package Marking Drawing AKM AK8817VQ XXXXXXX 1 AKM: AKM Logo AK8817VQ: Marketing Code XXXXXXX (7 digits): Date Code MS1113-E-00 2009/08 -43- [AK8817VQ] IMPORTANT NOTICE * These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, unclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. MS1113-E-00 2009/08 -44-