1
2013.11w
17mm
■Features
1. Low-profile, small PCB mounting area
Narrow width of only 2.5 mm reduced the board
footprint by approximately 17% to 57%, as compared to
several similar FH Series HRS connectors.
2. Various contact pitch (0.4mm, 0.5mm, 1mm
pitch) available
In addition to standard 0.5mm pitch, 0.4mm pitch, 1mm
pitch also available.
3. Increased FPC/FFC retention force
_ In the horizontal direction: Approximately 2.0 times
(compared to 0.5mm pitch FH12 series.)
_ In the vertical direction: Approximately 1.7 times
(compared to 0.5mm pitch FH19 series.)
4. Conductive traces on the PCB can run
under the connector
No exposed contacts on the bottom of the connector.
5. One finger operation of the actuator
Proven (in several other Hirose’s connectors) Flip-
Lock® rotating actuator assures reliable mechanical
and electrical connection with FPC/FFC, confirming it
with a definite tactile feel.
6.
Easy FPC insertion and reliable electrical
connection
Proven Flip Lock actuator allows easy insertion of
FPC/FFC and provides a tactile sensation when fully
closed, confirming complete electrical and mechanical
connection.
7. Accepts standard FPC thickness
0.3mm thick standard Flexible Printed Circuit (FPC) and
Flexible Flat Cable (FFC) can be used.
8. Board placement with automatic
equipment
Flat upper surface and tape and reel packaging
facilitate vacuum pick-up and placement.
Standard reel packaging contains 5000 connectors.
9. Halogen-free*
(FH33J Series)
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
●Small size
[ 30 pos. ]
Metal fittings (Leadless)
●Can be mounted over conductive traces.
No exposed contacts on the bottom of the
connector
●Simple operation
●Locked condition
1.2mm
2.5mm
FPC
Actuator
Actuator
FPC
1
2
3
3
4
0.4mm,0.5mm,1mm Pitch, 1.2mm abo ve the boar d, Flexib le Printed Cir cuit & Flexib le Flat Cable ZIF Connectors
FH33 Series
qOpen the actuator
wInsert FPC
eClose the actuator
rFPC connected
Increased FPC retention force
2
-----
-----
Temperature : -55ç/+15ç to +35ç/+85ç/+15ç to +35ç
Time : 30 /2 to 3 /30 /2 to 3 (Minutes)
5 cycles
Reflow : At the recommended temperature profile
Manual soldering
: 350ç ± 10ç for 5 seconds
1 mA
20 cycles
500 Mø min.
No flashover or insulation breakdown.
100 V DC
150 V AC /one minute, 120 V AC /one minute(0.4mm pitch type)
50 mø max.
100 mø max(0.4mm pitch type).
* Including FPC conductor resistance
Contact resistance: 50 mø max.
100 mø max(0.4mm pitch type).
No damage, cracks, or parts dislocation.
No electrical discontinuity of 1μs or more.
Contact resistance: 50 mø max.
100 mø max(0.4mm pitch type).
No damage, cracks, or parts dislocation.
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycles
in each of the 3 directions.
Acceleration of 981 m/s2, 6 ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis
Contact resistance: 50 mø max.
100 mø max(0.4mm pitch type).
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation.
96 hours at 40ç and humidity of 90% to 95%.
No deformation of components affecting performance.
■Materials
■Ordering information
FH 33 M H J - 12 (6)S B - 1 SH (10)
Series name:FH
Series No:33
Blank:0.5mm pitch,1mm pitch
M:0.4mm pitch
1
2
Material
LCP
PPS
LCP
PA
LCP
PPS
Phosphor bronze
PA Color:Beige
Color:Deep brown
Color:Beige
Color:Black
Color:Beige
Color:Deep brown
Color:Beige
Color:Black
Gold flash plated
Pure tin reflow plated
UL94V-0
Finish Remarks
Insulator
FH33 series
FH33J series
FH33M series
FH33MHJ series
Contacts
Metalfittings
Part
■Product Specifications
Ratings
Current rating 0.5 A
(0.4mm pitch type 0.4A)
Voltage rating 50 V AC
(0.4mm pitch type 40V AC)
Operating temperature range -55 ç to +85ç (Note 1)
Operating humidity range Relative humidity 90% max.
(No condensation)
Storage temperature range -10ç to +50ç (Note 2)
Storage humidity range Relative humidity 90% max. (No
condensation)
Recommended FPC Thickness = 0.3 ± 0.05mm gold plated (under 30 pos.), 0.3 ± 0.03mm gold plated (over 31 pos.)
4. Durability
(insertion/ withdrawal)
5. Vibration
6. Shock
7. Humidity
(Steady state)
8. Temperature cycle
9. Resistance to
soldering heat
3. Contact resistance
1.
Insulation resistance
2.
Withstanding voltage
Item Specification Conditions
Note 1: Includes temperature rise caused by current flow.
Note 2: The term ”storage” refers to products stored for long period of time prior to mounting and use. Operating
Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage,
shipment or during transportation.
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
10 11 12
1 3 4
25 6 7 8 9
3Blank:Standard
J:Halogen-free
Flame retardance UL94V-0
Standard type:Number of contacts
Eccentric type:Number of contacts
in 1mm housing
5
Blank:Width 3.0mm(standard)
H:Width 3.5mm(long actuator type)
4
6
Contact alignment:S: single
Eccentric direction:
Blank:standard type
B:Eccentric type
8
Standard type:Blank
Eccentric type:Number of
contacts
9
Plating specifications:
Blank:Gold plated
(10)...
Gold plating with nickel
barrier 5,000pieces/reel
(99)...Gold plating with nickel
barrier 500pieces/reel
Contact pitch:
0.4mm,0.5mm,1mm
SH:SMT horizontal mounting
12
10
11
7
3
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
0.15
D±0.1
2.25±0.15
U
G
∞Number of contacts
T
B
A±0.15
(C: FPC insertion slot dimension)
(0.15)
(0.15) F
Number of contacts indicator
Polarizing mark indicator Cav No.HRS mark
A**
(1)
Lot No. indicator
G
3
12
12
0
0.5±0.1
(1.1)
1.73±0.2
2.2±0.15
0.55±0.1
0.3+0.15
–0.1
0.25±0.1 0.15MAX
1.2±0.1
(1.8)
(120˚)
0.15MAX
0.35±0.1
a
0
■Connector Dimensions
Notes The coplanarity of each terminal lead is within 0.1 max.
The contact terminal lead position indicates the dimension
from the bottom a surface of the insulator body.
Difference of each terminal lead is within 0.1 max.
Slight variations in color of the plastic compounds do not
affect form, fit or function of the connector.
After reflow, the terminal plating may change color, however
this does not represent a quality issue.
1
2
3
4
5
Unit: mm
Note 1: Embossed reel packaging (5,000 pieces/reel, 500 pieces/reel).
Order by number of reels.
Part Number
FH33-6S-0.5SH (**)
FH33-9S-0.5SH (**)
FH33-10S-0.5SH (**)
FH33-12S-0.5SH (**)
FH33-14S-0.5SH (**)
FH33-19S-0.5SH (**)
FH33-20S-0.5SH (**)
FH33-26S-0.5SH (**)
FH33-28S-0.5SH (**)
FH33-30S-0.5SH (**)
FH33-32S-0.5SH (**)
FH33-36S-0.5SH (**)
FH33-40S-0.5SH (**)
FH33-45S-0.5SH (**)
FH33M-16S-0.4SH (**)
FH33J-4S-0.5SH (**)
FH33J-10S-0.5SH (**)
FH33J-12S-0.5SH (**)
FH33J-16S-0.5SH (**)
FH33J-18S-0.5SH (**)
FH33J-19S-0.5SH (**)
FH33J-40S-0.5SH (**)
FH33MHJ-65S-0.4SH (**)
580-1301-1-**
580-1303-7-**
580-1304-0-**
580-1302-4-**
580-1305-2-**
580-1307-8-**
580-1317-1-**
580-1306-5-**
580-1300-9-**
580-1312-8-**
580-1310-2-**
580-1311-5-**
580-1308-0-**
580-1316-9-**
580-1319-7-**
580-1329-0-**
580-1324-7-**
580-1328-8-**
580-1331-2-**
580-1334-0-**
580-1332-5-**
580-1330-0-**
580-1325-0-**
6
9
10
12
14
19
20
26
28
30
32
36
40
45
16
4
10
12
16
18
19
40
65
5
6.5
7
8
9
11.5
12
15
16
17
18
20
22
24.5
8.3
4
7
8
10
11
11.5
22
27.9
2.5
4
4.5
5.5
6.5
9
9.5
12.5
13.5
14.5
15.5
17.5
19.5
22
6
1.5
4.5
5.5
7.5
8.5
9
19.5
25.6
3.57
5.07
5.57
6.57
7.57
10.07
10.57
13.57
14.57
15.57
16.57
18.57
20.57
23.07
6.87
2.57
5.57
6.57
8.57
9.57
10.07
20.57
26.47
4.35
5.85
6.35
7.35
8.35
10.85
11.35
14.35
15.35
16.35
17.35
19.35
21.35
23.85
7.65
3.35
6.35
7.35
9.35
10.35
10.85
21.35
27.25
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.4
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.95
CL No. Number of Contacts AB C D T U
F
●0.4mm pitch, 0.5mm pitch type
4
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
△A**
(1.75)
(V)
1
(0.45) 2.25±0.15
(0.15)
B
A±0.15
(1)
(0.15)
(C: FPC insertion slot dimension)
D±0.1
0.15 G
G
∞Number of contacts
F
Lot No. indicator
Polarizing mark indicator Number of contacts indicator
HRS mark Cav No.
■Connector Dimensions
Unit: mm
Part Number
FH33-4S-1SH(**)
FH33-12(6)SB-1SH(**)
FH33J-12(6)SB-1SH(**)
580-1322-1-
**
580-1323-4-
**
580-1326-2-
**
4
6
6
CL No. Number of Contacts
6.5
8
8
A
3
5
5
B
5.07
6.57
6.57
C
5.85
7.35
7.35
1.75
1.25
1.25
D V
12
12
(120˚)
0
0.5±0.1
(1.1)
1.73±0.2
0.55±0.1
+0 15
0.25±0.1 0.15MAX
1.2±0.1
(1.8)
0.15MAX
0.35±0.1
a
0
F
Note 1: Embossed reel packaging (5,000 pieces/reel, 500 pieces/reel).
Order by number of reels.
Notes The coplanarity of each terminal lead is within 0.1 max.
The contact terminal lead position indicates the dimension
from the bottom a surface of the insulator body.
Difference of each terminal lead is within 0.1 max.
Slight variations in color of the plastic compounds do not
affect form, fit or function of the connector.
After reflow, the terminal plating may change color, however
this does not represent a quality issue.
1
2
3
4
5
●1mm pitch type
5
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
B
0.25±0.05(Metal mask)
0.1 H
H
(0.2)
(A)
(2.45)
J±0.1
K±0.1
0.8±0.05
2.8±0.05
(0.15)
(2.15)
(0.15)
(0.2)
(0.2)
∞Number of contacts 0.3±0.05(Land)
T
0.65±0.05
*Recommended metal mask thickness = 0.1mm
<over 31 pos.>0.3±0.03
<under 30 pos.>0.3±0.05
3.3MIN(Stiffener)
2-R0.2
T±0.07
E
0.3±0.03(FFC)
0.27±0.03(0.4mm pitch)
B±0.03
T±0.03
L±0.05
0.35±0.03(FPC)
2.3±0.3(Exposed area)
■Recommended PCB mounting pattern and metal mask dimensions
■Recommended FPC/FFC dimensions
Note 1: If the stiffener is less than 3.3 mm, E dimension must be 0.5 mm min.
Unit: mm
Part Number
FH33-6S-0.5SH (**)
FH33-9S-0.5SH (**)
FH33-10S-0.5SH (**)
FH33-12S-0.5SH (**)
FH33-14S-0.5SH (**)
FH33-19S-0.5SH (**)
FH33-20S-0.5SH (**)
FH33-26S-0.5SH (**)
FH33-28S-0.5SH (**)
FH33-30S-0.5SH (**)
FH33-32S-0.5SH (**)
FH33-36S-0.5SH (**)
FH33-40S-0.5SH (**)
FH33-45S-0.5SH (**)
FH33M-16S-0.4SH (**)
FH33J-4S-0.5SH (**)
FH33J-10S-0.5SH (**)
FH33J-12S-0.5SH (**)
FH33J-16S-0.5SH (**)
FH33J-18S-0.5SH (**)
FH33J-19S-0.5SH (**)
FH33J-40S-0.5SH (**)
FH33MHJ-65S-0.4SH (**)
580-1301-1-**
580-1303-7-**
580-1304-0-**
580-1302-4-**
580-1305-2-**
580-1307-8-**
580-1317-1-**
580-1306-5-**
580-1300-9-**
580-1312-8-**
580-1310-2-**
580-1311-5-**
580-1308-0-**
580-1316-9-**
580-1319-7-
**
580-1329-0-
**
580-1324-7-
**
580-1328-8-
**
580-1331-2-
**
580-1334-0-
**
580-1332-5-
**
580-1330-0-
**
580-1325-0-
**
6
9
10
12
14
19
20
26
28
30
32
36
40
45
16
4
10
12
16
18
19
40
65
5
6.5
7
8
9
11.5
12
15
16
17
18
20
22
24.5
8.3
4
7
8
10
11
11.5
22
27.9
2.5
4
4.5
5.5
6.5
9
9.5
12.5
13.5
14.5
15.5
17.5
19.5
22
6
1.5
4.5
5.5
7.5
8.5
9
19.5
25.6
3.8
5.3
5.8
6.8
7.8
10.3
10.8
13.8
14.8
15.8
16.8
18.8
20.8
23.3
7.1
2.8
5.8
6.8
8.8
9.8
10.3
20.8
26.7
4.9
6.4
6.9
7.9
8.9
11.4
11.9
14.9
15.9
16.9
17.9
19.9
21.9
24.4
8.2
3.9
6.9
7.9
9.9
10.9
11.4
21.9
27.8
3.5
5
5.5
6.5
7.5
10
10.5
13.5
14.5
15.5
16.5
18.5
20.5
23
6.8
2.5
5.5
6.5
8.5
9.5
10
20.5
26.4
CL No. Number of Contacts A B J K L
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.4
T
●0.4mm pitch, 0.5mm pitch type
●0.4mm pitch, 0.5mm pitch type
6
J
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
(A)
K±0.1
J±0.1
1.15±0.1
W±0.1
1
B
0.3±0.05(Land)
0.25±0.05(Metal mask)
(0.15)
(2.15)
(2.45)
(0.15) (0.2)
(0.2)
(0.2)
2.8±0.05
0.65±0.05
0.8±0.05
0.1 H
H
∞Number of contacts
*Recommended metal mask thickness = 0.1mm
■Recommended PCB mounting pattern and metal mask dimensions
●1mm pitch type
2-R0.2
1±0.1 0.65±0.1
1±0.1 X±0.1
B±0.1
L±0.1
<under 30 pos.>0.3±0.05
<over 31 pos.>0.3±0.03
3.3MIN(Stiffener)
2.3±0.3(Exposed area)
E
■Recommended FPC/FFC dimensions
●1mm pitch type
Unit: mm
Part Number
FH33-4S-1SH(**)
FH33-12(6)SB-1SH(**)
FH33J-12(6)SB-1SH(**)
580-1322-1-
**
580-1323-4-
**
580-1326-2-
**
4
6
6
CL No. Number of Contacts
6.5
8
8
A
3
5
5
B
5.3
6.8
6.8
6.4
7.9
7.9
5
6.5
6.5
1.15
0.65
0.65
1
0.5
0.5
K L W X
7
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■FH33 Series FPC/FFC Construction (Recommended Specifications)
1. Using Single-sided FPC
Material Name
Covering film layer
Cover adhesive
Surface treatment
Copper foil
Base adhesive
Base film
Reinforcement material adhesive
Stiffener
Polyimide 1 mil thick
Nickel under plated 1 to 5μm /
Gold plated 0.2μm
Cu 1oz
Heat-hardened adhesive
Polyimide 1 mil thick
Heat-hardened adhesive
Polyimide 7 mil thick
Total
(25)
(25)
3
35
25
25
30
175
293
Material
Thickness (μm)
2. Using Double-sided FPC
Material Name
Covering film layer
Cover adhesive
Surface treatment
Through-hole copper
Copper foil
Base adhesive
Base film
Base adhesive
Copper foil
Cover adhesive
Covering film layer
Reinforcement material adhesive
Stiffener
Polyimide 1 mil thick
Nickel under plated 1 to 5μm /
Gold plated 0.2μm
Cu
Cu 1/2oz
Heat-hardened adhesive
Polyimide 1 mil thick
Heat-hardened adhesive
Cu 1/2oz
Polyimide 1 mil thick
Heat-hardened adhesive
Polyimide 4 mil thick
Total
(25)
(25)
3
15
18
18
25
18
18
25
25
50
100
297
Material
Thickness (μm)
1. This specification is a recommendation for the construction of the FH33 Series FPC and FFC (t=0.3 ± 0.05).
2. For details about the construction, please contact the FPC/FFC manufacturers.
πPractical tolerance of thickness dimension is ±20 μm
3. Using FFC
4. Precautions
Gold plated, soft copper film
Adhesive
Polyester
Adhesive
Stiffener
Polyester film
Adhesive
Polyester
Polyester
Polyester
Total
polyester thermoplastic type
(12)
(30)
35
30
12
30
188
295
Material Name Material
Thickness (μm)
8
(Ø13)
(Ø80)
(Ø380)
(R:INSIDE)
(S:OUTSIDE)
End section Mounting section
Embossed carrier tape
Blank section
Lead section (400 mm min.)
Blank section Top cover tape
(10 pockets min.)
(10 pockets min.)
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
Note: 5,000 pieces per reel.
Embossed tape 32 mm or wider will have perforated feed holes on two sides.
●Reel Dimensions
■Packaging Specifications
●Embossed Carrier Tape Dimensions
(Tape width up to 24mm)
●Embossed Carrier Tape Dimensions
(Tape width 32mm and over)
9
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
Unit: mm
Part Number
FH33-6S-0.5SH (**)
FH33-9S-0.5SH (**)
FH33-10S-0.5SH (**)
FH33-12S-0.5SH (**)
FH33-14S-0.5SH (**)
FH33-19S-0.5SH (**)
FH33-20S-0.5SH (**)
FH33-26S-0.5SH (**)
FH33-28S-0.5SH (**)
FH33-30S-0.5SH (**)
FH33-32S-0.5SH (**)
FH33-36S-0.5SH (**)
FH33-40S-0.5SH (**)
FH33-45S-0.5SH (**)
FH33M-16S-0.4SH (**)
FH33J-4S-0.5SH (**)
FH33J-10S-0.5SH (**)
FH33J-12S-0.5SH (**)
FH33J-16S-0.5SH (**)
FH33J-18S-0.5SH (**)
FH33J-19S-0.5SH (**)
FH33J-40S-0.5SH (**)
FH33MHJ-65S-0.4SH (**)
FH33-4S-1SH (**)
FH33-12(6)S-1SH (**)
FH33J-12(6)S-1SH (**)
580-1301-1-**
580-1303-7-**
580-1304-0-**
580-1302-4-**
580-1305-2-**
580-1307-8-**
580-1317-1-**
580-1306-5-**
580-1300-9-**
580-1312-8-**
580-1310-2-**
580-1311-5-**
580-1308-0-**
580-1316-9-**
580-1319-7-
**
580-1329-0-
**
580-1324-7-
**
580-1328-8-
**
580-1331-2-
**
580-1334-0-
**
580-1332-5-
**
580-1330-0-
**
580-1325-0-
**
580-1322-1-
**
580-1323-4-
**
580-1326-2-
**
6
9
10
12
14
19
20
26
28
30
32
36
40
45
16
4
10
12
16
18
19
40
65
4
6
6
16
16
16
16
16
24
24
24
24
24
32
32
44
44
24
16
16
16
24
24
24
44
44
16
16
16
7.5
7.5
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
20.2
20.2
11.5
7.5
7.5
7.5
11.5
11.5
11.5
20.2
20.2
7.5
7.5
7.5
--------
--------
--------
--------
--------
--------
--------
--------
--------
--------
28.4
28.4
40.4
40.4
--------
--------
--------
--------
--------
--------
--------
40.4
40.4
--------
--------
--------
5.3
6.8
7.3
8.3
9.3
11.8
12.3
15.3
16.3
17.3
18.3
20.3
22.3
24.8
8.6
4.3
7.3
8.3
10.3
11.3
11.8
22.3
28.2
6.8
8.3
8.3
CL No. Number of Contacts M N P Q
17.4
17.4
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
45.4
45.4
25.4
17.4
17.4
17.4
25.4
25.4
25.4
45.4
45.4
17.4
17.4
17.4
21.4
21.4
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
49.4
49.4
29.4
21.4
21.4
21.4
29.4
29.4
29.4
49.4
49.4
21.4
21.4
21.4
R S
10
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■Recommended Temperature Profile
●Using Lead-free Solder paste
MAX 250ç
Start
Temperature
(ç)
Time (Seconds)
25ç (60 sec.)
(60 sec.)
90 to 120 sec.
Preheating
Sodering
0
50
100
150 150ç
200ç
230ç
200
250
HRS test conditions
Solder method : Reflow, IR/hot air
Environment : Room air
Solder composition
: Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.’s Part Number: M705-
221CM5-32-10.5)
Test board : Glass epoxy 25mm∞50mm∞0.8mm thick
Land dimensions
: Contacts lead 0.3mm∞0.65mm
Metal fittings 0.55mm∞0.8mm
Metal mask : Contacts lead 0.25mm∞0.65mm∞0.1mm
thick
Metal fittings 0.55mm∞0.8mm∞0.1mm
thick
This temperature profile is based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume/thickness and
board
size/thickness. Consult your solder paste and equipment
manufacturer for specific recommendations.
11
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
■
Operation and Precautions
Operation
1.FPC insertion procedure. Connector installed on the board.
Lift up the actuator. Use thumb or index finger.
1
2.FPC removal
Lift up the actuator. Carefully withdraw the
FPC.
1
Fully insert the FPC in the connector paral-
lel to mounting surface, with the exposed
conductive traces facing down.
2
Rotate down the actuator until firmly closed. It is
critical that the inserted FPC is not moved and
remains fully inserted.
3
FPC conductor
surface (Bottom side)
12
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
Axis of rotation
(120˚)
Damege to the contacts
Damage to the contacts
Precautions
Exercise care when handling connectors. Follow recommendations given
below.
PC board flexing
SPC board connector mounting area
The connectors are straight within 0.1 mm max.
Make sure that the PC board connector mounting area flatness can accept the connector terminals
without causing any failure of the solder joints.
SHandling before mounting on PCB
Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT
RECOMMENDED.
SPC Board handling
Exercise caution when handling boards with the connectors installed. Do not apply any forces
affecting soldered joints.
Precautions When Inserting or Removing FPC
Pay attention to the following points when inserting FPC.
SActuator operation
Do not apply excessive force when opening the actuator prior to FPC insertion. When opening
make sure that the force is applied only to the actuator itself, avoiding touching of the contacts.
Connector
PCB
Assure free rotation of
the actuator
1
Axis of rotation
2
The actuator will rotate 120 degrees
maximum. Do not force it to rotate further.
3
120°
13
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
Actuator
FPC
Precautions
When operating the actuator, do so at the
center portion.
4
As illustrated, do not attempt removal or re-
positioning of the actuator.
5
SFPC Insertionq
The FPC should be aligned parallel with the board surface and perpendicular with the connector (as
shown), then completely inserted.
To assure correct electrical and mechanical connection do not insert FPC at angle. It must be fully
inserted.
Make sure that the FPC is NOT MOVED during the closing of the actuator.
Perpendicular with
the connector
SFPC Insertionw
When inserting the FPC, do not forcefully rub against the bottom surface of the connector insertion
entrance. Doing so will result in the contacts and FPC making strong contact and may cause
deformation of the contacts, peeling of the FPC conductor, and other problems.
Peeling of FPC
conductor
14
Precautions
120°
Other Precautions
SHand Soldering Precautions
When hand soldering:
Do not perform reflow or hand soldering with the FPC inserted in the connector.
Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
Do not use excessive amount of solder or flux compounds.
Operation of the actuator and contacts may be affected by excessive amounts of solder or flux
compounds.
1
2
3
Removing the FPC
Rotate the actuator to the open position (maximum open angle of 120°). Carefully withdraw the FPC.
Routing the FPC (FPC fully inserted/ actuator closed)
SFPC Load
Do not apply force in excess of 0.15N max. in the upward direction (as illustrated). Do not bend the
FPC too close to the actuator.
Load: 0.15N max.
SVerification of the fully closed actuator.
The actuator should be fully closed (as illustrated) and the FPC held firmly in the connector.
Do not press against the actuator when is fully closed. Max force applied to the fully closed actuator
should not exceed 1 N.
FH33 Series●0.4mm,0.5 mm,1mm Pitch, 1.2 mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
15
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
NOTES :
16
FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors
The contents of this catalog are current as of date of 11/2013. Contents are subject to change without notice for the pur pose of improvements.
6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-K u,Yokohama-Shi 224-8540,J APAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
®
USA:
HIROSE ELECTRIC (U.S.A.), INC. Headquarters
2688 Westhills Court, Simi Valley, CA 93065-6235
Phone : 1-805-522-7958
Fax : 1-805-522-3217
http://www.hiroseusa.com
HONG KONG:
HIROSE ELECTRIC HONGKONG TRADING CO., LTD.
Unit 1102 A&B, Energy Plaza, 92 Granville Road,
Tsim Sha Tsui East, Kowloon
Phone : 852-2803-5338
Fax : 852-2591-6560
http://www.hirose-hongkong.com.hk
CHINA:
HIROSE ELECTRIC CO., LTD. BEIJING REPRESENTATIVE OFFICE
A1001, Ocean International Center, Building 56# East 4th
Ring Middle Road, Chao Yang District, Beijing, 100025
Phone : 86-10-5165-9332
Fax : 86-10-5908-1381
http://www.hirose-china.com.cn
TAIWAN:
HIROSE ELECTRIC TAIWAN CO., LTD.
103 8F, No.87, Zhengzhou Rd., Taipei
Phone : 886-2-2555-7377
Fax : 886-2-2555-7350
http://www.hirose-taiwan.com.tw
GERMANY:
HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH
Herzog-Carl-Strasse 4 D-73760 Ostfildern
(Scharnhauser Park)
Phone : 49-711-4560-02-1
Fax : 49-711-4560-02-299
http://www.hirose.de
SINGAPORE:
HIROSE ELECTRIC CO., LTD.
10 Anson Road #26-16 International Plaza 079903
Phone : 65-6324-6113
Fax : 65-6324-6123
http://www.hirose-singapore.com.sg
THE NETHERLANDS:
HIROSE ELECTRIC EUROPE B.V.
Hogehillweg #8 1101 CC Amsterdam Z-O
Phone : 31-20-6557460
Fax : 31-20-6557469
http://www.hiroseeurope.com
UK:
HIROSE ELECTRIC EUROPE B.V. UK BRANCH
First Floor, St Andrews House, Caldecotte Lake
Business Park, Milton Keynes MK7 8LE
Phone : 44-1908-369060
Fax : 44-1908-369078
http://www.hirose.co.uk
USA:
HIROSE ELECTRIC (U.S.A.), INC. Detroit Office (Automotive)
37677 Professional Center Drive, Suite #100C
Livonia, MI 48154
Phone : 1-734-542-9963
Fax : 1-734-542-9964
http://www.hiroseusa.com
USA:
HIROSE ELECTRIC (U.S.A.), INC. North California Office
20400 Stevens Creek Blvd., Ste 250, Cupertino, CA
95014
Phone : 1-408-253-9640
Fax : 1-408-253-9641
http://www.hiroseusa.com
CHINA:
HIROSE ELECTRIC (SHANGHAI) CO., LTD.
1501-02, Cross Tower Building, 318 Fuzhou Road,
Huang Pu District, Shanghai 200001
Phone : 86-21-6391-3355
Fax : 86-21-6335-0767
http://www.hirose-china.com.cn
CHINA:
HIROSE ELECTRIC CO., LTD. SHENZHEN OFFICE
Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre
5002, ShenNanDong Road, ShenZhen City, Guangdong Province, 518008
Phone : 86-755-8207-0851
Fax : 86-755-8207-0873
http://www.hirose-china.com.cn
KOREA:
HIROSE KOREA CO., LTD.
1261-10, Jeoungwhang-Dong, Shihung-City,
Kyunggi-Do 429-450
Phone : 82-31-496-7000,7124
Fax : 82-31-496-7100
http://www.hirose.co.kr
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Hirose Electric:
FH33-26S-0.5SH(10) FH33-14S-0.5SH(10) FH33-12S-0.5SH(10) FH33-9S-0.5SH(10) FH33-28S-0.5SH(10) FH33-
10S-0.5SH(10) FH33-6S-0.5SH(10) FH33-19S-0.5SH FH33-19S-0.5SH(10) FH33-20S-0.5SH FH33-20S-0.5SH(10)
FH33-30S-0.5SH FH33-30S-0.5SH(10) FH33-32S-0.5SH(10) FH33-36S-0.5SH(10) FH33-40S-0.5SH(10) FH33-45S-
0.5SH(10) FH33M-16S-0.4SH(10) FH33-10S-0.5SH FH33-14S-0.5SH FH33-26S-0.5SH FH33-28S-0.5SH FH33-6S-
0.5SH FH33-12(6)SB-1SH(10) FH33-4S-1SH(10) FH33J-10S-0.5SH(10) FH33J-12(6)SB-1SH(10) FH33J-12S-
0.5SH(10) FH33J-16S-0.5SH(10) FH33J-18S-0.5SH(10) FH33J-19S-0.5SH(10) FH33J-40S-0.5SH(10) FH33J-4S-
0.5SH(10) FH33MHJ-65S-0.4SH(10) FH33W-6S-0.5SH(10) FH33-28S-0.5SH(99) FH33-12S-0.5SH(99) FH33-9S-
0.5SH(99) FH33-10S-0.5SH(99) FH33-26S-0.5SH(99) FH33M-16S-0.4SH(99) FH33W-6S-0.5SH(99) FH33-4S-
1SH(99) FH33MHJ-65S-0.4SH(99) FH33J-12(6)SB-1SH(99) FH33J-4S-0.5SH(99) FH33J-40S-0.5SH(99) FH33J-
18S-0.5SH(99) FH33-30S-0.5SH(99) FH33-12(6)SB-1SH(99) FH33J-12S-0.5SH(99) FH33-45S-0.5SH(99) FH33-
32S-0.5SH(99) FH33J-19S-0.5SH(99) FH33-40S-0.5SH(99) FH33-19S-0.5SH(99) FH33-36S-0.5SH(99) FH33-6S-
0.5SH(99) FH33J-10S-0.5SH(99) FH33-20S-0.5SH(99) FH33J-16S-0.5SH(99) FH33-14S-0.5SH(99)