NCV8703 300 mA, Ultra-Low Quiescent Current, IQ 12 mA, Ultra-Low Noise, LDO Voltage Regulator The NCV8703 is a low noise, low power consumption and low dropout Linear Voltage Regulator. With its excellent noise and PSRR specifications, the device is ideal for use in products utilizing RF receivers, imaging sensors, audio processors or any component requiring an extremely clean power supply. The NCV8703 uses an innovative Adaptive Ground Current circuit to ensure ultra low ground current during light load conditions. http://onsemi.com TSOP-5 SN SUFFIX CASE 483 Features Operating Input Voltage Range: 2.0 V to 5.5 V Available in Fixed Voltage Options: 0.8 to 3.5 V MARKING DIAGRAMS Contact Factory for Other Voltage Options Ultra-Low Quiescent Current of Typ. 12 mA Ultra-Low Noise: 13 mVRMS from 100 Hz to 100 kHz Very Low Dropout: 180 mV Typical at 300 mA 2% Accuracy Over Load/Line/Temperature High PSRR: 68 dB at 1 kHz Internal Soft-Start to Limit the Turn-On Inrush Current Thermal Shutdown and Current Limit Protections Stable with a 1 mF Ceramic Output Capacitor Available in TSOP-5 and XDFN 1.5 x 1.5 mm Package Active Output Discharge for Fast Turn-Off NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable These are Pb-Free Devices Satellite Radio Receivers, GPS Rear View Camera, Electronic Mirrors, Lane Change Detectors Portable Entertainment Systems Other Battery Powered Applications VIN CIN IN 1 mF ON EN NCV8703 GND VOUT OUT COUT 1 mF Ceramic 1 XXXAYW G 1 X, XXX = Specific Device Code M = Date Code A = Assembly Location Y = Year W = Work Week G = Pb-Free Package PIN CONNECTIONS 1 IN OUT GND N/C 5-Pin TSOP-5 (Top View) 1 OUT N/C GND IN N/C EN 6-Pin XDFN 1.5 x 1.5 mm (Top View) See detailed ordering and shipping information in the package dimensions section on page 15 of this data sheet. Figure 1. Typical Application Schematic Semiconductor Components Industries, LLC, 2013 XM G ORDERING INFORMATION OFF June, 2013 - Rev. 1 5 EN Typical Applications XDFN6 MX SUFFIX CASE 711AE 1 Publication Order Number: NCV8703/D NCV8703 IN ENABLE LOGIC EN BANDGAP REFERENCE UVLO INTEGRATED SOFT-START THERMAL SHUTDOWN MOSFET DRIVER WITH CURRENT LIMIT OUT AUTO LOW POWER MODE ACTIVE DISCHARGE EN GND Figure 2. Simplified Schematic Block Diagram Table 1. PIN FUNCTION DESCRIPTION Pin No. XDFN6 Pin No. TSOP-5 Pin Name 1 5 OUT Regulated output voltage pin. A small 1 mF ceramic capacitor is needed from this pin to ground to assure stability. 2 4 N/C Not connected. 3 2 GND Power supply ground. Connected to the die through the lead frame. Soldered to the copper plane allows for effective heat dissipation. 4 3 EN Enable pin. Driving EN over 0.9 V turns on the regulator. Driving EN below 0.4 V puts the regulator into shutdown mode. N/C Not connected. This pin can be tied to ground to improve thermal dissipation. 5 6 1 IN Description Input pin. A small capacitor is needed from this pin to ground to assure stability. Table 2. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit VIN -0.3 V to 6 V V Output Voltage VOUT -0.3 V to VIN + 0.3 V V Enable Input VEN -0.3 V to VIN + 0.3 V V Output Short Circuit Duration tSC Indefinite s TJ(MAX) 125 C Input Voltage (Note 1) Maximum Junction Temperature Storage Temperature TSTG -55 to 150 C ESD Capability, Human Body Model (Note 2) ESDHBM 2000 V ESD Capability, Machine Model (Note 2) ESDMM 200 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AEC-Q100-002 (EIA/JESD22-A114) ESD Machine Model tested per AEC-Q100-003 (EIA/JESD22-A115) Latchup Current Maximum Rating tested per JEDEC standard: JESD78. http://onsemi.com 2 NCV8703 Table 3. THERMAL CHARACTERISTICS (Note 3) Symbol Value Thermal Characteristics, TSOP-5, Thermal Resistance, Junction-to-Air Thermal Characterization Parameter, Junction-to-Lead (Pin 2) qJA yJL 241 129 Thermal Characteristics, XDFN6 1.5 x 1.5 mm Thermal Resistance, Junction-to-Air Thermal Characterization Parameter, Junction-to-Board qJA yJB 146 77 Rating Unit C/W C/W 3. Single component mounted on 1 oz, FR4 PCB with 645 mm2 Cu area. Table 4. ELECTRICAL CHARACTERISTICS (-40C TJ 125C; VIN = VOUT(NOM) + 0.5 V or 2.0 V, whichever is greater; VEN = 0.9 V, IOUT = 10 mA, CIN = COUT = 1 mF unless otherwise noted. Typical values are at TJ = +25C.) (Note 4) Parameter Test Conditions Operating Input Voltage Symbol Min Typ Max Unit 5.5 V 1.9 V +2 % VIN 2.0 Undervoltage Lock-out VIN rising UVLO 1.2 Output Voltage Accuracy VOUT + 0.5 V VIN 5.5 V, IOUT = 0 - 300 mA VOUT -2 Line Regulation VOUT + 0.5 V VIN 4.5 V, IOUT = 10 mA RegLINE 450 mV/V VOUT + 0.5 V VIN 5.5 V, IOUT = 10 mA RegLINE 600 mV/V Load Regulation IOUT = 0 mA to 300 mA RegLOAD 20 mV/mA Load Transient IOUT = 1 mA to 300 mA or 300 mA to 1 mA in 1 ms, COUT = 1 mF TranLOAD -100/ +150 mV Dropout Voltage (Note 5) IOUT = 300 mA, VOUT(nom) = 2.5 V VDO 180 300 mV Output Current Limit VOUT = 90% VOUT(nom) ICL 450 750 mA Quiescent Current IOUT = 0 mA IQ 12 20 mA Ground Current IOUT = 300 mA IGND 200 mA Shutdown Current VEN 0.4 V, TJ = +25C IDIS 0.12 mA VEN 0 V, VIN = 2.0 to 4.5 V, TJ = -40 to +85C IDIS 0.55 310 1.6 2 mA EN Pin Threshold Voltage High Threshold Low Threshold VEN Voltage Increasing VEN Voltage Decreasing EN Pin Input Current VEN = 5.5 V IEN 100 Turn-On Time COUT = 1.0 mF, from assertion EN pin to 98% VOUT(nom) tON 200 ms Power Supply Rejection Ratio VIN = 3 V, VOUT = 2.5 V IOUT = 300 mA PSRR 70 68 53 dB Output Noise Voltage VOUT = 2.5 V, VIN = 3 V, IOUT = 300 mA f = 100 Hz to 100 kHz VN 13 mVrms Thermal Shutdown Temperature Temperature increasing from TJ = +25C TSD 160 C Thermal Shutdown Hysteresis Temperature falling from TSD TSDH VEN_HI VEN_LO f = 100 Hz f = 1 kHz f = 10 kHz V 0.9 - 0.4 20 500 - nA C 4. Performance guaranteed over the indicated operating temperature range by design and/or characterization. Production tested at TJ = TA = 25_C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 5. Characterized when VOUT falls 100 mV below the regulated voltage at VIN = VOUT(NOM) + 0.5 V. http://onsemi.com 3 NCV8703 OUTPUT VOLTAGE NOISE (mV/rtHz) TYPICAL CHARACTERISTICS 10 1 RMS Output Noise (mVRMS) IOUT = 10 mA 0.1 0.01 0.001 VIN = 2.0 V VOUT = 0.8 V CIN = COUT = 1 mF MLCC, X7R, 1206 size 0.01 0.1 IOUT = 1 mA IOUT 10 Hz - 100 kHz 100 Hz - 100 kHz 1 mA 18.45 17.77 10 mA 17.18 16.43 300 mA 14.14 13.11 IOUT = 300 mA 1 10 100 1000 FREQUENCY (kHz) OUTPUT VOLTAGE NOISE (mV/rtHz) Figure 3. Output Voltage Noise Spectral Density for VOUT = 0.8 V, COUT = 1 mF 10 1 RMS Output Noise (mVRMS) IOUT = 300 mA 0.1 0.01 0.001 VIN = 2.0 V VOUT = 0.8 V CIN = 1 mF COUT = 4.7 mF MLCC, X7R, 1206 size 0.01 IOUT = 10 mA IOUT 10 Hz - 100 kHz 100 Hz - 100 kHz 13.14 1 mA 14.07 10 mA 16.59 15.83 300 mA 15.46 14.53 IOUT = 1 mA 0.1 1 10 100 1000 FREQUENCY (kHz) OUTPUT VOLTAGE NOISE (mV/rtHz) Figure 4. Output Voltage Noise Spectral Density for VOUT = 0.8 V, COUT = 4.7 mF 10 1 RMS Output Noise (mVRMS) IOUT = 10 mA 0.1 0.01 0.001 VIN = 3.8 V VOUT = 3.3 V CIN = COUT = 1 mF MLCC, X7R, 1206 size 0.01 0.1 IOUT 10 Hz - 100 kHz 100 Hz - 100 kHz 1 mA 20.29 17.06 10 mA 19.76 16.11 300 mA 18.74 15.46 IOUT = 1 mA IOUT = 300 mA 1 10 100 1000 FREQUENCY (kHz) Figure 5. Output Voltage Noise Spectral Density for VOUT = 3.3 V, COUT = 1 mF http://onsemi.com 4 NCV8703 OUTPUT VOLTAGE NOISE (mV/rtHz) TYPICAL CHARACTERISTICS 10 1 RMS Output Noise (mVRMS) IOUT = 300 mA 0.1 VIN = 3.8 V VOUT = 3.3 V CIN = 1 mF COUT = 4.7 mF MLCC, X7R, 1206 size 0.01 0.001 0.01 IOUT = 10 mA IOUT 10 Hz - 100 kHz 100 Hz - 100 kHz 1 mA 17.64 13.52 10 mA 19.54 15.96 300 mA 21.50 18.71 IOUT = 1 mA 0.1 1 10 100 1000 FREQUENCY (kHz) Figure 6. Output Voltage Noise Spectral Density for VOUT = 3.3 V, COUT = 4.7 mF 160 315 VOUT = 0.8 V 280 IGND, GROUND CURRENT (mA) IGND, GROUND CURRENT (mA) 350 VOUT = 3.3 V 245 VOUT = 2.5 V 210 175 140 VIN = VOUT + 0.5 V CIN = 1 mF COUT = 1 mF MLCC, X7R, 1206 size 105 70 35 0 0 50 100 150 200 250 VOUT = 2.5 V 100 VOUT = 0.8 V 80 VIN = VOUT + 0.5 V CIN = 1 mF COUT = 1 mF MLCC, X7R, 1206 size 60 40 20 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 IOUT, OUTPUT CURRENT (mA) IOUT, OUTPUT CURRENT (mA) Figure 7. Ground Current vs. Output Current Figure 8. Ground Current vs. Output Current from 0 mA to 2 mA 160 240 TJ = 25C 210 TJ = 125C IGND, GROUND CURRENT (mA) IGND, GROUND CURRENT (mA) VOUT = 3.3 V 120 0 300 270 TJ = -40C 180 150 120 VIN = VOUT + 0.5 V CIN = 1 mF COUT = 1 mF MLCC, X7R, 1206 size 90 60 30 0 140 0 30 60 90 120 150 180 140 TJ = -40C 100 TJ = 125C 80 60 VIN = VOUT + 0.5 V CIN = 1 mF COUT = 1 mF MLCC, X7R, 1206 size 40 20 0 210 240 270 300 TJ = 25C 120 0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 IOUT, OUTPUT CURRENT (mA) IOUT, OUTPUT CURRENT (mA) Figure 9. Ground Current vs. Output Current at Temperatures Figure 10. Ground Current vs. Output Current 0 mA to 2 mA at Temperatures http://onsemi.com 5 NCV8703 TYPICAL CHARACTERISTICS 40 13.5 VOUT = 0.8 V Iq, QUIESCENT CURRENT (mA) Iq, QUIESCENT CURRENT (mA) 14.0 13.0 12.5 VOUT = 3.3 V 12.0 VOUT = 2.5 V 11.5 11.0 VIN = VOUT + 0.5 V CIN = 1 mF COUT = 1 mF MLCC, X7R 1206 size 10.5 10.0 9.5 9.0 -40 -20 0 20 40 60 80 100 120 2 3 4 5 6 Figure 11. Quiescent Current vs. Temperature Figure 12. Quiescent Current vs. Input Voltage 0.805 CIN = 1 mF COUT = 1 mF MLCC, X7R 1206 size 3.0 2.5 VOUT = 3.3 V VOUT, OUTPUT VOLTAGE (V) VOUT, OUTPUT VOLTAGE (V) 10 VIN, INPUT VOLTAGE (V) VOUT = 2.5 V 2.0 1.5 VOUT = 0.8 V 1.0 0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 0.804 0.803 0.802 VIN = 2 V VOUT = 0.8 V CIN = 1 mF COUT = 1 mF 0.801 0.800 0.799 0.798 0.797 0.796 0.795 -40 -20 0 20 40 60 80 100 120 140 VIN, INPUT VOLTAGE (V) TJ, JUNCTION TEMPERATURE (C) Figure 13. Output Voltage vs. Input Voltage Figure 14. Output Voltage vs. Temperature - 0.8 V 3.3050 VIN = VOUT + 0.5 V VOUT = 2.5 V CIN = 1 mF COUT = 1 mF 2.5025 2.5015 2.5005 2.4995 2.4985 2.4975 2.4965 -40 -20 0 20 40 60 80 100 120 VOUT, OUTPUT VOLTAGE (V) 2.5035 VOUT, OUTPUT VOLTAGE (V) 20 TJ, JUNCTION TEMPERATURE (C) 3.5 0 30 0 140 CIN = 1 mF COUT = 1 mF VOUT = 3.3 V MLCC, X7R 1206 size 140 3.3025 3.3000 3.2975 3.2950 3.2925 VIN = VOUT + 0.5 V VOUT = 3.3 V CIN = 1 mF COUT = 1 mF 3.2900 3.2875 3.2850 -40 -20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 15. Output Voltage vs. Temperature - 2.5 V Figure 16. Output Voltage vs. Temperature - 3.3 V http://onsemi.com 6 NCV8703 TYPICAL CHARACTERISTICS 1000 900 900 800 800 700 700 REGLINE (mV/V) REGLINE (mV/V) 1000 600 500 400 300 200 VOUT = 1.8 V VIN = 2.3 to 5.5 V CIN = 1 mF COUT = 1 mF IOUT = 10 mA 100 0 -40 -20 0 20 40 60 80 100 120 140 40 60 80 100 120 140 20 18 16 REGLOAD (mV) REGLINE (mV/V) VOUT = 3.3 V VIN = 3.8 to 5.5 V CIN = 1 mF COUT = 1 mF IOUT = 10 mA 0 20 14 12 VOUT = 1.8 V VIN = 2.3 V CIN = 1 mF COUT = 1 mF IOUT = 0 mA to 300 mA 10 8 6 4 40 60 80 100 120 2 0 -40 -20 140 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 19. Line Regulation vs. Temperature - 3.3 V Figure 20. Load Regulation vs. Temperature - 1.8 V 20 18 VOUT = 2.8 V VIN = 3.3 V CIN = 1 mF COUT = 1 mF IOUT = 0 mA to 300 mA 16 REGLOAD (mV) REGLOAD (mV) 20 Figure 18. Line Regulation vs. Temperature - 2.8 V 20 12 0 Figure 17. Line Regulation vs. Temperature - 1.8 V 0 -40 -20 14 VOUT = 2.8 V VIN = 3.3 to 5.5 V CIN = 1 mF COUT = 1 mF IOUT = 10 mA TJ, JUNCTION TEMPERATURE (C) 600 16 300 TJ, JUNCTION TEMPERATURE (C) 800 18 400 100 0 -40 -20 1000 200 500 200 1200 400 600 10 8 6 14 12 VOUT = 3.3 V VIN = 3.8 V CIN = 1 mF COUT = 1 mF IOUT = 0 mA to 300 mA 10 8 6 4 4 2 0 -40 -20 2 0 -40 -20 0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 21. Load Regulation vs. Temperature - 2.8 V Figure 22. Load Regulation vs. Temperature - 3.3 V http://onsemi.com 7 NCV8703 TYPICAL CHARACTERISTICS VOUT = 2.5 V CIN = 1 mF COUT = 1 mF 200 250 TJ = 25C VDROP, DROPOUT VOLTAGE (mV) VDROP, DROPOUT VOLTAGE (mV) 250 TJ = 125C 150 100 TJ = -40C 50 0 0 50 100 150 200 250 300 IOUT = 300 mA 175 IOUT = 200 mA 150 125 100 IOUT = 100 mA 75 50 25 0 -40 -20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) Figure 23. Dropout vs. Output Current - 2.5 V Figure 24. Dropout vs. Temperature - 2.5 V 750 VOUT = 3.3 V VIN = 3.8 V CIN = 1 mF COUT = 1 mF IOUT = 10 mA 725 700 675 VEN, ENABLE VOLTAGE (mV) VEN, ENABLE VOLTAGE (mV) 200 VOUT = 2.5 V CIN = 1 mF COUT = 1 mF IOUT, OUTPUT CURRENT (mA) 750 650 625 600 575 550 -40 -20 0 20 40 60 80 100 120 VOUT = 3.3 V VIN = 3.8 V CIN = 1 mF COUT = 1 mF IOUT = 10 mA 725 700 675 650 625 600 575 550 -40 -20 140 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 25. Enable Threshold - High Figure 26. Enable Threshold - Low ISHORT, SHORT CIRCUIT CURRENT (mA) 600 ICL, CURRENT LIMIT (mA) 225 550 500 450 VIN = 2.3 V VOUT = 1.8 V CIN = 1 mF COUT = 1 mF MLCC, X7R, size 1206 400 350 300 -40 -20 0 20 40 60 80 100 120 140 600 550 500 450 VIN = 2.3 V VOUT = 1.8 V CIN = 1 mF COUT = 1 mF MLCC, X7R, size 1206 400 350 300 -40 -20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 27. Output Current Limit Figure 28. Short Circuit Limit http://onsemi.com 8 120 140 NCV8703 TYPICAL CHARACTERISTICS 70 RR, RIPPLE REJECTION (dB) 80 60 50 VIN = 2.3 V VOUT = 1.8 V CIN = none COUT = 1 mF MLCC, X7R, 1206 size 40 30 20 10 0 0.01 0.1 1 10 100 1000 10,000 60 VIN = 3.8 V VOUT = 3.3 V CIN = none COUT = 1 mF MLCC, X7R, 1206 size 0.01 0.1 VIN = 3.0 V VOUT = 2.5 V CIN = none COUT = 1 mF MLCC, X7R, 1206 size 40 30 20 10 0 0.01 0.1 1 10 100 1000 10,000 1 10 100 1000 10,000 Cout = 1mF Cout = 4.7m Cout = 10m 90 80 70 60 50 40 VIN = 3.8 V VOUT = 3.3 V CIN = none MLCC, X7R, 1206 size 30 20 10 0 0.01 0.1 1 10 100 1000 10,000 F, FREQUENCY (kHz) F, FREQUENCY (kHz) Figure 31. Power Supply Rejection Ratio, VOUT = 3.3 V Figure 32. Power Supply Rejection Ratio, VOUT = 3.3 V, IOUT = 10 mA 10 100 Cout = 1mF Cout = 4.7m Cout = 10m 90 80 Unstable Region 70 60 ESR (W) RR, RIPPLE REJECTION (dB) 50 100 Iout = 1 mA Iout = 10 mA Iout = 100 mA Iout = 200 mA Iout = 300 mA 50 10 0 60 Figure 30. Power Supply Rejection Ratio, VOUT = 2.5 V 70 20 70 Figure 29. Power Supply Rejection Ratio, VOUT = 1.8 V 80 30 80 F, FREQUENCY (kHz) 90 40 Iout = 1 mA Iout = 10 mA Iout = 100 mA Iout = 200 mA Iout = 300 mA 90 F, FREQUENCY (kHz) 100 RR, RIPPLE REJECTION (dB) 100 Iout = 1 mA Iout = 10 mA Iout = 100 mA Iout = 200 mA Iout = 300 mA 90 RR, RIPPLE REJECTION (dB) RR, RIPPLE REJECTION (dB) 100 50 40 30 20 10 0 VIN = 3.8 V VOUT = 3.3 V CIN = none MLCC, X7R, 1206 size 0.01 0.1 VOUT = 3.3 V 1 VOUT = 0.8 V Stable Region 1 10 100 1000 10,000 0.1 VIN = 5.5 V CIN = COUT = 1 mF MLCC, X7R, 1206 size 0 50 100 150 200 250 300 F, FREQUENCY (kHz) IOUT, OUTPUT CURRENT (mA) Figure 33. Power Supply Rejection Ratio, VOUT = 3.3 V, IOUT = 300 mA Figure 34. Output Capacitor ESR vs. Output Current http://onsemi.com 9 NCV8703 VEN IINRUSH 1 V / div 1 V / div IINRUSH 600 mV / div VEN VOUT VOUT 100 ms / div 100 ms / div 600 mV / div VEN IOUT 1 V / div VOUT VOUT 1 ms / div Figure 38. Enable Turn-off Response 500 mV / div VIN = 3.8 V to 4.8 V VOUT = 3.3 V IOUT = 10 mA CIN = 1 mF COUT = 1 mF 20 mV / div 20 mV / div 500 mV / div Figure 37. Enable Turn-on Response - COUT = 10 mF trise = 1 ms COUT = 4.7 mF COUT = 1 mF 100 ms / div VIN VIN = 3.8 V VOUT = 3.3 V VEN = 0.9 V IOUT = 10 mA CIN = 1 mF VOUT VIN tFALL = 1 ms VIN = 3.8 V to 4.8 V VOUT = 3.3 V IOUT = 10 mA CIN = 1 mF COUT = 1 mF VOUT 2 ms / div 2 ms / div Figure 39. Line Transient Response - Rising Edge, VOUT = 3.3 V Figure 40. Line Transient Response - Falling Edge, VOUT = 3.3 V http://onsemi.com 10 100 mA / div VIN = 3.8 V VOUT = 3.3 V VEN = 0.9 V IOUT = 10 mA CIN = 1 mF COUT = 1 mF IINRUSH 1 V / div Figure 36. Enable Turn-on Response - COUT = 4.7 mF 100 mA / div 600 mV / div Figure 35. Enable Turn-on Response - COUT = 1 mF VEN VIN = 3.8 V VOUT = 3.3 V VEN = 0.9 V IOUT = 10 mA CIN = 1 mF COUT = 4.7 mF 100 mA / div VIN = 3.8 V VOUT = 3.3 V VEN = 0.9 V IOUT = 10 mA CIN = 1 mF COUT = 1 mF 100 mA / div 600 mV / div TYPICAL CHARACTERISTICS NCV8703 VOUT 100 mA / div IOUT 40 mV / div VIN = 2 V VOUT = 0.8 V CIN = 1 mF (MLCC) COUT = 4.7 mF COUT = 1 mF IOUT VIN = 2 V VOUT = 0.8 V CIN = 1 mF (MLCC) COUT = 1 mF COUT = 4.7 mF VOUT 50 ms / div Figure 41. Load Transient Response - Rising Edge, VOUT = 0.8 V, IOUT = 1 mA to 300 mA, COUT = 1 mF, 4.7 mF Figure 42. Load Transient Response - Falling Edge, VOUT = 0.8 V, IOUT = 1 mA to 300 mA, COUT = 1 mF, 4.7 mF VIN = 2 V VOUT = 0.8 V CIN = 1 mF (MLCC) Cout = 1 mF (MLCC) IOUT VOUT 100 mA / div 20 ms / div 40 mV / div 40 mV / div 100 mA / div 40 mV / div 100 mA / div TYPICAL CHARACTERISTICS trise = 10 ms trise = 1 ms VIN = 3.8 V VOUT = 3.3 V CIN = 1 mF (MLCC) IOUT VOUT COUT = 4.7 mF 10 ms / div Figure 43. Load Transient Response - Rising Edge, VOUT = 0.8 V, IOUT = 1 mA to 300 mA, tRISE = 1 ms, 10 ms Figure 44. Load Transient Response - Rising Edge, VOUT = 3.3 V, IOUT = 1 mA to 300 mA, COUT = 1 mF, 4.7 mF 100 mA / div VIN = 3.8 V VOUT = 3.3 V CIN = 1 mF (MLCC) IOUT VIN = 3.8 V VOUT = 3.3 V CIN = 1 mF (MLCC) Cout = 1 mF (MLCC) IOUT VOUT COUT = 1 mF 40 mV / div 40 mV / div 100 mA / div COUT = 1 mF 20 ms / div COUT = 4.7 mF VOUT trise = 1 ms trise = 10 ms 50 ms / div 10 ms / div Figure 45. Load Transient Response - Falling Edge, VOUT = 3.3 V, IOUT = 1 mA to 300 mA, COUT = 1 mF, 4.7 mF Figure 46. Load Transient Response - Rising Edge, VOUT = 3.3 V, IOUT = 1 mA to 300 mA, tRISE = 1 ms, 10 ms http://onsemi.com 11 NCV8703 TYPICAL CHARACTERISTICS VOUT 300 mV / div VOUT = 3.3 V IOUT = 1 mA CIN = 1 mF (MLCC) Cout = 1 mF (MLCC) Thermal Shutdown VIN = 3.8 V VOUT = 3.3 V CIN = 1 mF (MLCC) Cout = 1 mF (MLCC) 300 mA / div 600 mV / div Short Circuit VIN VOUT IOUT 5 ms / div 10 ms / div Figure 47. Turn-on/off - Slow Rising VIN Figure 48. Short Circuit and Thermal Shutdown APPLICATIONS INFORMATION General Output Decoupling (COUT) The NCV8703 is a high performance 300 mA Low Dropout Linear Regulator. This device delivers excellent noise and dynamic performance. Thanks to its adaptive ground current feature the device consumes only 12 mA of quiescent current at no-load condition. The regulator features ultra-low noise of 13 mVRMS, PSRR of 68 dB at 1 kHz and very good load/line transient performance. Such excellent dynamic parameters and small package size make the device an ideal choice for powering the precision analog and noise sensitive circuitry in portable applications. The LDO achieves this ultra low noise level output without the need for a noise bypass capacitor. A logic EN input provides ON/OFF control of the output voltage. When the EN is low the device consumes as low as typ. 120 nA from the IN pin. The device is fully protected in case of output overload, output short circuit condition and overheating, assuring a very robust design. The NCV8703 requires an output capacitor connected as close as possible to the output pin of the regulator. The recommended capacitor value is 1 mF and X7R or X5R dielectric due to its low capacitance variations over the specified temperature range. The NCV8703 is designed to remain stable with minimum effective capacitance of 0.1 mF to account for changes with temperature, DC bias and package size. Especially for small package size capacitors such as 0402 the effective capacitance drops rapidly with the applied DC bias. Refer to the Figure 49, for the capacitance vs. package size and DC bias voltage dependence. Input Capacitor Selection (CIN) It is recommended to connect a minimum of 1 mF Ceramic X5R or X7R capacitor close to the IN pin of the device. This capacitor will provide a low impedance path for unwanted AC signals or noise modulated onto constant input voltage. There is no requirement for the min. /max. ESR of the input capacitor but it is recommended to use ceramic capacitors for their low ESR and ESL. A good input capacitor will limit the influence of input trace inductance and source resistance during sudden load current changes. Larger input capacitor may be necessary if fast and large load transients are encountered in the application. Figure 49. Capacitance Change vs. DC Bias There is no requirement for the minimum value of Equivalent Series Resistance (ESR) for the COUT but the maximum value of ESR should be less than 900 m. Larger http://onsemi.com 12 NCV8703 current measured when the output voltage drops on the 90% of the nominal VOUT. When the Output Voltage is directly shorted to ground (VOUT = 0 V), the short circuit protection will limit the output current to 520 mA (typ). The current limit and short circuit protection will work properly up to VIN = 5.5 V at TA = 25C. There is no limitation for the short circuit duration. output capacitors and lower ESR could improve the load transient response or high frequency PSRR as shown in typical characteristics. It is not recommended to use tantalum capacitors on the output due to their large ESR. The equivalent series resistance of tantalum capacitors is also strongly dependent on the temperature, increasing at low temperature. The tantalum capacitors are generally more costly than ceramic capacitors. Internal Soft-Start circuit NCV8703 contains an internal soft-start circuitry to protect against large inrush currents which could otherwise flow during the start-up of the regulator. Soft-start feature protects against power bus disturbances and assures a controlled and monotonic rise of the output voltage. No-load Operation The regulator remains stable and regulates the output voltage properly within the 2% tolerance limits even with no external load applied to the output. Enable Operation The EN pin is used to enable/disable the LDO and to deactivate/activate the active discharge function. If the EN pin voltage is <0.4 V the device is guaranteed to be disabled. The pass transistor is turned-off so that there is virtually no current flow between the IN and OUT. The active discharge transistor is active so that the output voltage VOUT is pulled to GND through a 320 resistor. In the disable state the device consumes as low as typ. 120 nA from the VIN. If the EN pin voltage >0.9 V the device is guaranteed to be enabled. The NCV8703 regulates the output voltage and the active discharge transistor is turned-off. The EN pin has internal pull-down current source with typ. value of 110 nA which assures that the device is turned-off when the EN pin is not connected. Build in 2 mV hysteresis into the EN prevents from periodic on/off oscillations that can occur due to noise. In the case where the EN function isn't required the EN should be tied directly to IN. Thermal Shutdown When the die temperature exceeds the Thermal Shutdown threshold (TSD - 160C typical), Thermal Shutdown event is detected and the device is disabled. The IC will remain in this state until the die temperature decreases below the Thermal Shutdown Reset threshold (TSDU - 140C typical). Once the IC temperature falls below the 140C the LDO is enabled again. The thermal shutdown feature provides the protection from a catastrophic device failure due to accidental overheating. This protection is not intended to be used as a substitute for proper heat sinking. Power Dissipation As power dissipated in the NCV8703 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. The maximum power dissipation the NCV8703 can handle is given by: Undervoltage Lockout The internal UVLO circuitry assures that the device becomes disabled when the VIN falls below typ. 1.5 V. When the VIN voltage ramps-up the NCV8703 becomes enabled, if VIN rises above typ. 1.6 V. The 100 mV hysteresis prevents from on/off oscillations that can occur due to noise on VIN line. P D(MAX) + TJ(MAX) * TA q JA (eq. 1) The power dissipated by the NCV8703 for given application conditions can be calculated from the following equations: Output Current Limit P D [ V INI GND@I OUT ) I OUTV IN * V OUT (eq. 2) Output Current is internally limited within the IC to a typical 490 mA. The NCV8703 will source this amount of http://onsemi.com 13 NCV8703 450 0.50 400 0.45 350 0.40 PD(MAX), TA = 25C, 1 OZ Cu 300 qJA, 1 OZ Cu 250 0.30 qJA, 2 OZ Cu 200 150 0.35 0 100 200 300 400 500 PCB Copper Area (mm2) 0.25 PD(MAX), Maximum Power Dissipation (W) qJA, Junction to Ambient Thermal Resistance (C/W) PD(MAX), TA = 25C, 2 OZ Cu 0.20 700 600 Figure 50. qJA and PD(MAX) vs. Copper Area (TSOP-5) 0.90 PD(MAX), TA = 25C, 2 OZ Cu 350 0.80 300 0.70 250 PD(MAX), TA = 25C, 1 OZ Cu 200 0.50 qJA, 1 OZ Cu 150 100 0.60 qJA, 2 OZ Cu 0 100 200 300 400 500 PCB Copper Area (mm2) 600 700 0.40 PD(MAX), Maximum Power Dissipation (W) qJA, Junction to Ambient Thermal Resistance (C/W) 400 0.30 800 Figure 51. qJA vs. Copper Area (XDFN6) Reverse Current Power Supply Rejection Ratio The PMOS pass transistor has an inherent body diode which will be forward biased in the case that VOUT > VIN. Due to this fact in cases, where the extended reverse current condition can be anticipated the device may require additional external protection. The NCV8703 features very good Power Supply Rejection ratio. If desired the PSRR at higher frequencies in the range 100 kHz - 10 MHz can be tuned by the selection of COUT capacitor and proper PCB layout. Output Noise The IC is designed for ultra-low noise output voltage without external noise filter capacitor (Cnr). Figures 3 - 6 shows NCV8703 noise performance. Generally the noise performance in the indicated frequency range improves with increasing output current. Although even at IOUT = 1 mA the noise levels are below 20 mVRMS. Load Regulation The NCV8703 features very good load regulation of typically 6 mV in 0 mA to 300 mA range. In order to achieve this very good load regulation a special attention to PCB design is necessary. The trace resistance from the OUT pin to the point of load can easily approach 100 m which will cause 30 mV voltage drop at full load current, deteriorating the excellent load regulation. Turn-On Time The turn-on time is defined as the time period from EN assertion to the point in which VOUT will reach 98% of its nominal value. This time is dependent on various application conditions such as VOUT(NOM), COUT, TA. Line Regulation The IC features very good line regulation of 0.6 mV/V measured from VIN = VOUT + 0.5 V to 5.5 V. For battery operated applications it may be important that the line regulation from VIN = VOUT + 0.5 V up to 4.5 V is only 0.45 mV/V. http://onsemi.com 14 NCV8703 PCB Layout Recommendations minimize the solution size, use 0402 capacitors. Larger copper area connected to the pins will also improve the device thermal resistance. The actual power dissipation can be calculated from Equation 2. To obtain good transient performance and good regulation characteristics place CIN and COUT capacitors close to the device pins and make the PCB traces wide. In order to ORDERING INFORMATION Device* Voltage Option Marking NCV8703MX18TCG 1.8 V J NCV8703MX28TCG 2.8 V K NCV8703MX30TCG 3.0 V L NCV8703MX33TCG 3.3 V P NCV8703SN18T1G 1.8 V VEC NCV8703SN28T1G 2.8 V VED NCV8703SN30T1G 3.0 V VEE NCV8703SN33T1G 3.3 V VEF Package Shipping XDFN6 3000 / Tape & Reel TSOP5 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable http://onsemi.com 15 NCV8703 PACKAGE DIMENSIONS XDFN6 1.5x1.5, 0.5P CASE 711AE ISSUE A D L A B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.20mm FROM TERMINAL TIP. L1 DETAIL A IIII IIII IIII ALTERNATE TERMINAL CONSTRUCTIONS E PIN ONE REFERENCE EE EE EXPOSED Cu 0.10 C 2X 2X 0.10 C DIM A A1 A3 b D E e L L1 L2 TOP VIEW MOLD CMPD DETAIL B ALTERNATE CONSTRUCTIONS A DETAIL B A3 0.05 C MILLIMETERS MIN MAX 0.35 0.45 0.00 0.05 0.13 REF 0.20 0.30 1.50 BSC 1.50 BSC 0.50 BSC 0.40 0.60 --0.15 0.50 0.70 A1 0.05 C C SIDE VIEW DETAIL A e 1 RECOMMENDED MOUNTING FOOTPRINT* SEATING PLANE 6X 5X 0.35 5X 0.73 L 3 L2 1.80 0.83 6 4 6X b DIMENSIONS: MILLIMETERS 0.10 C A BOTTOM VIEW 0.05 C 0.50 PITCH *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. B NOTE 3 http://onsemi.com 16 NCV8703 PACKAGE DIMENSIONS TSOP-5 CASE 483-02 ISSUE K 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION A. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. D 5X NOTE 5 0.20 C A B 0.10 T M 2X 0.20 T B 5 1 4 2 B S 3 K DETAIL Z G A A TOP VIEW DIM A B C D G H J K M S DETAIL Z J C 0.05 H SIDE VIEW C SEATING PLANE END VIEW MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 17 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV8703/D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ON Semiconductor: NCV8703SN30T1G NCV8703SN33T1G NCV8703SN28T1G NCV8703MX18TCG NCV8703MX28TCG NCV8703MX33TCG NCV8703SN18T1G