70 Headers with Solder Pins, Pin Spacing 7.62 mm / 0.3 in, orange Pin spacing 7.62 mm / 0.3 in, orange Straight solder pin 300 V, OAO NW 400 V/6 kV/3 12A0/16A@ |} 300V,15AQ0W 300V,15A Pin spacing 7.62 mm / 0.3 in, orange Right angle solder pin 400 V/6kV/3_ | 300 V, OAG@AW 12A0/16AQ@ | 300V, 15AQN 300V,15A Mating direction perpendicular to PCB WESHVODOOMBVNVOIEY Mating direction parallel to PCB * WES @OOQOOOBVNVE EG No. of Item-No. Item-No. poles Closed end headers, orange, straight solder pin 1x 1mm @ 1.2x1.2mm@Q@ 2 231-732/001-000 231-762/001-000 3 231-733/001-000 231-763/001-000 4 231-734/001-000 231-764/001-000 231-735/001-000 231-765/001-000 6 231-736/001-000 231-766/001-000 7 231-737/001-000 231-767/001-000 8 231-738/001-000 231-768/001-000 9 231-739/001-000 231-769/001-000 10 231-740/001-000 231-770/001-000 11 231-741/001-000 231-771/001-000 12 231-742/001-000 231-772/001-000 No. of Item-No. {tem-No. poles Closed end headers, orange, right angle solder pin Txlmm@ 1.2x1.2mm@ 2 231-932/001-000 231-962/001-000 3 231-933/001-000 231-963/001-000 4 231-934/001-000 231-964/001-000 5 231-935/001-000 231-965/001-000 6 231-936/001-000 231-966/001-000 7 231-937/001-000 231-967/001-000 8 231-938/001-000 231-968/001-000 9 231-939/001-000 231-969/001-000 10 231-940/001-000 231-970/001-000 V1 231-941/001-000 231-971/001-000 42 231-942/001-000 231-972/001-000 Coding key, snap-on type, light grey 231-130 Separator, for formation of groups, light grey 231-500 Accessories (please refer to remarks concerning coding on page 5.75) Coding key, snap-on type, light grey 231-130 Separator, for formation of groups, light grey 231-500 Fixing element, horizontal, orange 231-393 Screw M 2 x 12 with nut 231-195 for fixing element Tapping Screw, B2.2x 13 231-194 fixing hole @ 1.8 mm Dimensions (in mm) Diameter of drilled hole: 1.4*'mm (solder pin 1 x 1 mm); 1.7 *'mm (solder pin 1.2 x 1.2 mm) re e ' \ 4 A= (No. of poles - 1) x pin spacing + 8 mm A= (No. of poles - 1) x pin spacing + 8 mm B=A+ 5.08 mm;C=B+74mm * For international approvals (with corresponding ratings) see pages 10.3 - 10.38. Note: These connectors can only be mated and unmated at voltages below 42 V and in the No load condition, For mating and unmating at low power values, please request data.