Edition 2016-02
EC centrifugal fans - RadiPac
The ebm-papst RadiPac EC centrifugal fan series is more efficient than
ever.
This was achieved by the logical advanced development of the aero-
dynamics and motor technology.
While materials of higher quality were used in the motors to reduce
internal losses, the centrifugal impeller has undergone an entirely
new development!
Furthermore, the installation situation preferred later in air handling units
was already given proper consideration in the design of the blade channel.
This has a tremendous effect on the energy balance during operation and
results in drastic energy savings....
In the future, sizes 250 and 280 will be made of high-strength composite
material. For sizes 310 to 560, we will continue to use sheet aluminum,
with the difference being that the blade with a hollow profile achieves the
greatest stability and the design produces the best aeroacoustic proper-
ties.
Sizes 630 to 900 are still produced with our proven aerodynamics.
But the new aerodynamics technology will soon be available for
these sizes as well.
The new RadiPac fans are characterized especially
by the following points:
– Best overall efficiency
– Comfortable noise level
– Compact design
– Consistent series
– Fast availability
– Easy startup (uncomplicated configuration of the control electronics)
– Well coordinated system (preconfigured motor / control electronics /
impeller system)
– Logistic advantages due to complete unit
– EC motor without rare earth magnets
Production selection software is available on request to help you make
a convenient and quick selection, calculate the lifecycle costs, and to
compare products.
Additional information on the subjects of efficiency, dependability, and
commitment is available in special editions 1 and 2 of the special
techmag publications.
RadiPac: Now even better!
2
2016-02
RadiPac ø 630 54
RadiPac ø 710 58
RadiPac ø 800 62
RadiPac ø 900 66
RadiPac ø 280 - ø 450 (compact design) 70
Technology:
- Tender specifi cations 74
- Accessories 79
- Conn. diagrams 91
- Technical parameters & scope 98
ebm-papst agents 102
RadiPac: Now even better! 2
About ebm-papst. 4
Overview of products 6
Overview of curves 8
RadiPac ø 250 12
RadiPac ø 280 18
RadiPac ø 310 24
RadiPac ø 355 30
RadiPac ø 400 36
RadiPac ø 450 40
RadiPac ø 500 46
RadiPac ø 560 50
3
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Contents
4
2016-02
About ebm-papst.
As a leader in technologies for ventilation and drive engineering, ebm-papst is in demand
as an engineering partner in many sectors. With over 15,000 different products, we
provide the right solution for just about any challenge. Our fans and drives are reliable,
quiet and energy-efficient.
Six reasons that make us the ideal partner:
Our systems expertise.
You want the best solution for every project. The inter relationships
between ventilation and drive engineering must thus be considered
as a whole. And that’s what we do – with motor technology that sets
standards, sophisticated electronics and aerodynamic designs –
all from a single source and perfectly matched. These system solutions
release unique synergies worldwide. And in particular – they relieve you
of a lot of work, so that you can concentrate on your core competency.
The ebm-papst spirit of invention.
In addition to our wide range of products, we are always able to develop
customized solutions for you. A diversified team of 600 engineers and
technicians works at our three locations in Germany: Mulfingen, Landshut
and St. Georgen. Contact us to discuss your next project.
Our lead in technology.
As pioneer and trail-blazer for developing highly efficient EC tech nology,
we are way ahead of other motor manufacturers. Almost our entire product
range is also available with GreenTech EC technology. The list of benefits is
long: higher efficiency, main tenance-free, longer service life, sound reduc-
tion, intelligent control characteristics and incomparable energy efficiency
with savings of up to 80 % compared to conventional AC technology. Let
our technology be your competitive advantage as you lead in your industry.
Proximity to our customers.
ebm-papst owns 57 sales offices worldwide, of which 47 are sub sidiaries
with an extensive network of sales representatives and distributors. You
will always have a local contact, someone who speaks your language and
knows your market.
Our standard of quality.
Of course you can rely on the highest standards of quality with our pro-
ducts. Our quality management is uncompromising, at every step in every
process. This is underscored by our certification according to international
standards including DIN EN ISO 9001, ISO/TS 16949-2 and DIN EN ISO
14001.
Our sustainable approach.
Assuming responsibility for the environment, for our employees and for
society is an integral part of our corporate philosophy. We develop
products with an eye to maximum environmental compatibility, in particu-
lar resource-preserving production methods. We promote environmental
awareness among our young staff and are actively involved in sporting,
cultural activities and education. That’s what makes us a leading company
– and an ideal partner for you.
The story of our success
to market and technology pioneer.
5
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
1963 Founding of Elektrobau Mulfingen GmbH & Co. KG by Gerhard Sturm and Heinz Ziehl.
1965 First tubeaxial fan developed in EC/DC technology.
1966 ebm-papst’s success takes off with the new 68 motor.
1972 The first ebm-papst foreign subsidiary is established in Sweden.
1988 Gerhard Sturm is awarded the Federal Cross of Merit.
1990 The sixty-millionth external-rotor fan is produced.
1992 Acquisition of PAPST Motoren GmbH in St. Georgen.
1997 Buyout of the Landshut (mvl) plant.
1998 Development of first fans with integrated electronics.
2003 Change of name to ebm-papst.
2008 The HyBlade® range of fans sets new efficiency standards.
2010 GreenTech – our sign for energy efficiency and resource preservation.
2011 RadiCal defines a new standard for EC centrifugal fans.
2013 ebm-papst takes over the gearbox specialist Zeitlauf and wins the German Sustainability Award.
2014 Team partnership with Mercedes AMG PETRONAS Formula 1 team.
2015 RadiPac pushes the limits of efficiency.
Product overview RadiPac
Data is subject to change without notice at ebm-papst discretion.
M3G 084-DF 1~200-277
M3G 084-DF 1~200-277250
R3G 250-PR04 -H1 K3G 250-PR04 -H2 ---
R3G 250-PR17 -I1 K3G 250-PR17 -I2 --- 12
Motor
Nominal
voltage
range
VAC
Centrifugal fan Centrifugal module
with support bracket
Centrifugal module
with cube design
ØPage
ff.
6
2016-02
M3G 084-DF 3~380-480 R3G 250-PR02 -J1 K3G 250-PR02 -J2 ---
M3G 084-DF 1~200-277
M3G 084-DF 1~200-277280
R3G 280-PR03 -H1 K3G 280-PR03 -H2 ---
R3G 280-PR04 -I1 K3G 280-PR04 -I2 --- 18
M3G 084-FA 3~380-480 R3G 280-PS10 -J1 K3G 280-PS10 -J2 ---
M3G 084-GF 3~380-480
M3G 112-GA 3~380-480310
R3G 310-PT08 -J1 K3G 310-PT08 -J2 ---
R3G 310-PH38 -01 K3G 310-PH38 -02 --- 24
M3G 112-GA 3~380-480 R3G 310-PH58 -01 K3G 310-PH58 -02 ---
M3G 112-EA 3~380-480
M3G 112-GA 3~380-480355
R3G 355-PJ75 -01 K3G 355-PJ75 -01 ---
R3G 355-PH49 -01 K3G 355-PH49 -02 --- 30
M3G 112-IA 3~380-480 R3G 355-PI93 -01 K3G 355-PI93 -02 ---
M3G 112-IA 3~380-480
M3G 150-FF 3~380-480
400 R3G 400-PI92 -01 K3G 400-PI92 -02 ---
R3G 400-PA27 -71 K3G 400-PA27 -71 --- 36
M3G 112-IA 3~380-480
M3G 150-FF 3~380-480
450
R3G 450-PI86 -01 K3G 450-PI86 -02 ---
R3G 450-PA23 -71 K3G 450-PA23 -71 --- 40
M3G 150-IF 3~380-480 R3G 450-PB24 -01 K3G 450-PB24 -01 ---
M3G 150-FF 3~380-480
M3G 150-IF 3~380-480
500 R3G 500-PA23 -71 K3G 500-PA23 -71 ---
R3G 500-PB33 -01 K3G 500-PB33 -01 --- 46
M3G 150-IF 3~380-480
M3G 150-NA 3~380-480
560 R3G 560-PB31 -71 K3G 560-PB31 -71 ---
R3G 560-PC04 -01 K3G 560-PC04 -01 --- 50
RadiPac: The best solution
0,50
0,75
Max.
input
power
kW
1,18
0,50
0,75
1,05
1,23
1,80
2,95
1,10
1,90
2,68
2,50
3,35
1,74
2,90
5,25
3,45
5,70
3,30
5,00
Example:
R3G .....
Example:
K3G .....
7
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Product overview RadiPac
M3G 150-NA 3~380-480
M3G 200-HF 3~380-480630
R3G 630-AP01 -01 K3G 630-AP01 -01 ---
--- --- K3G 630-AR02 -01 54
Motor
Ø
M3G 200-QA 3~380-480 --- --- K3G 630-AS05 -01
M3G 150-NA 3~380-480
M3G 200-LA 3~380-480710
R3G 710-AP02 -01 K3G 710-AP02 -01 ---
--- --- K3G 710-AR03 -01 58
M3G 200-QA 3~380-480 --- --- K3G 710-AS06 -01
M3G 200-QA 3~380-480
M3G 200-QA 3~380-480
800 --- --- K3G 800-AR08 -01
--- --- K3G 800-AS07 -01 62
M3G 200-QA 3~380-480
M3G 200-QA 3~380-480
900 --- --- K3G 900-AR10 -01
--- --- K3G 900-AS08 -01 66
M3G 084-GF 3~380-480
M3G 112-GA 3~380-480
280 R3G 280-AJ14 -C1 --- ---
R3G 310-BC38 -01 --- ---
70
Motor
Ø
M3G 112-GA 3~380-480 R3G 355-BD43 -01 --- ---
M3G 150-FF 3~380-480
M3G 150-FF 3~380-480
R3G 400-AS23 -01 --- ---
R3G 450-AS24 -01 --- ---
310
355
400
450
RadiPac: The powerful solution
RadiPac: The compact solution
Compact designTechnologyAgents
2,90
6,75
11,00
2,80
7,86
11,80
7,53
11,60
7,52
8,70
0,99
1,65
1,73
2,84
2,38
Nominal
voltage
range
VAC
Centrifugal fan
(compact design)
Centrifugal module
with support bracket
Centrifugal module
with cube design
Page
ff.
Max.
input
power
kW
Nominal
voltage
range
VAC
Centrifugal fan Centrifugal module
with support bracket
Centrifugal module
with cube design
Page
ff.
Max.
input
power
kW
Example:
R3G .....
Example:
K3G .....
Example:
R3G .....
Overview of curves RadiPac
50002500 7500 10000 12500 15000 17500
qvm³/h25000 30000100005000 15000 20000
Pfs Pa
500
1000
8.06.04.02.0 in wg
cfm
1500
2000
250
750
7.05.03.01.0
1250
1750
Ø 400
Ø 310
Ø 500
Ø 250
Ø 710
Ø 450
Ø 900
Ø 560
Ø 630
Ø 800
Ø 355
Ø 280
8
2016-02
The graph shows the maximum air performance for each size. If less performance is required, variants with smaller motors can be used.
This saves additional costs. The right fan for every application!
RadiPac in the Product Selector
To aid in selection of the right fan, ebm-papst provides the
"Product Selector" software with an integrated "Black-Box" module
for incorporation in customer device configuration programs.
With this new program, you can use the operating point as a selection
criterion for RadiPac fans.
If there is more than one fan in the specified power range, the displayed
aerodynamic and acoustic data can be used to select and document the
most suitable fan.
The difference between the measurements and the data published in the
"Product Selector" software was tested by TÜV SÜD and the accuracy of
the calculation was assigned to class B0.
You can also have the life cycle costs calculated for the selected fans.
You can make your selection based on point of operation or type
designation.
Data sheets can be created in PDF format and show not only a fan‘s
nominal data but also its performance data at the specified operating
point together with the intake and outlet sound power levels over the
octave band.
Just ask your contact at ebm-papst!
9
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
10
2016-02
EC centrifugal fans – RadiPac
11
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
12
2016-02
EC centrifugal fans – RadiPac
backward curved, Ø 250
Curves:
qvm³/h
cfm
Pfs Pa
in wg
500 1000 1500 2000 2500 3000 3500
0 400 800 1200 1600 2000
400
800
1200
1 2 3 4 5 6
11
3
3
3
4
4
4
1
2
2
2
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Subject to change
Type Motor
*3G 250 M3G 084-DF P. 94 / P5)
Nominal data
Techn. features
and connection
diagram
*3G 250 M3G 084-DF P. 94 / P5)
VAC Hz rpm kW A °C kg
1~200-277 50/60 3080 0,50 2,30 -25..+40 4,2
Curve
A
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
1~200-277 50/60 3450 0,75 3,30 -25..+40 4,6
B
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: PP plastic
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 6
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 55
– Insulation class: "F"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
*3G 250 M3G 084-DF P. 95 / P6) 3~380-480 50/60 4000 1,18 1,80 -25..+40 4,5
C
n
rpm
Ped
kW
I
A
LWA
dB(A)
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
3375
3135
3080
3200
3605
3505
3450
3525
4000
4000
4000
4000
0,49
0,50
0,50
0,50
0,62
0,73
0,75
0,73
0,86
1,13
1,18
1,11
2,12
2,30
2,30
2,30
2,71
3,20
3,30
3,17
1,34
1,75
1,80
1,71
89
79
75
79
91
83
77
81
91
85
83
86
(1) Nominal data at operating point with maximum load and 230 or 400 VAC.
=@max.
3
B
C
A
13
Information
ø 250ø 280ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 94 f.
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Cable exit: Variable
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
A B EN 60335-1
– Approvals: C22.2 Nr.77 + CAN/CSA-E60730-1, UL 1004-7 + 60730
– Efficiency: Ecodesign EU regulation EU 327/2011
Centrifugal fan
R3G 250-PR04 -H1
R3G 250-PR17 -I1
kg
4,2
4,6
kg
8,5
8,9
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap
96355-2-4013
96355-2-4013
R3G 250-PR02 -J1 4,5 8,896355-2-4013
Centrifugal module
with support bracket
K3G 250-PR04 -H2
K3G 250-PR17 -I2
K3G 250-PR02 -J2
Conn. diagram
P. 94 f.
Inlet ring
P. 82 ff.
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
Drawings
P. 14 ff.
ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
14
2016-02
EC centrifugal fans – RadiPac
backward curved, Ø 250
R3G 250-PR04-H1 (Centrifugal fan)
K3G 250-PR04-H2 (Centrifugal module with support bracket)
116.8
152.5
±1.8
Ø164
±0.35
M6 (4x)
4x90°
45°
85
±10
1000
+20
8
Ø150
±0.35
Ø172.5
±0.3
Ø270
Ø178
47.7
10
48
Ø280
Ø11 (4x)
298
234.7
±3
85
±10
8
1000
+20
187
±2
2
10
1.5
350
400
Max. clearance for screw 16 mm
Cable PVC AWG22,
5x crimped ferrules
Accessory part: Inlet ring 96355-2-4013
Not included in scope of delivery (k-factor: 76)
Dimensions: see “Accessories” chapter
Attachment for inlet ring and FlowGrid (4x)
Cable PVC AWG18,
5x crimped ferrules
Pressure tap (k-factor: 76)
15
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 250-PR17-I1 (Centrifugal fan)
K3G 250-PR17-I2 (Centrifugal module with support bracket)
116.8
10
152.5
±1.8
Ø186
±0.5
M6 (4x)
4x90°
45°
85
±10
1000
+20
8
Ø169
±0.35
Ø172.5
±0.3
Ø270
Ø200
64.1
48
Ø280
Ø11 (4x)
298
251.1
±3
85
±10
8
1000
+20
187
±2
2
10
1.5
350
400
Max. clearance for screw 16 mm
Cable PVC AWG22,
5x crimped ferrules
Accessory part: Inlet ring 96355-2-4013
Not included in scope of delivery (k-factor: 76)
Dimensions: see “Accessories” chapter
Cable PVC AWG18,
5x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 76)
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 250
16
2016-02
R3G 250-PR02-J1 (Centrifugal fan)
K3G 250-PR02-J2 (Centrifugal module with support bracket)
116.8
10
152.5
±1.8
Ø186
±0.5
M6 (4x)
4x90°
45°
85
±10
1000
+20
8
Ø169
±0.35
Ø172.5
±0.3
Ø270
Ø200
64.1
48
Ø280
Ø11 (4x)
298
251.1
±3
85
±10
8
1000
+20
187
±2
2
10
1.5
350
400
Max. clearance for screw 16 mm
Cable PVC AWG22,
5x crimped ferrules
Accessory part: Inlet ring 96355-2-4013
Not included in scope of delivery (k-factor: 76)
Dimensions: see “Accessories” chapter
Cable PVC AWG18,
6x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 76)
EC centrifugal fans – RadiPac
backward curved, Ø 250
17
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
18
2016-02
qvm³/h
cfm
Pfs Pa
in wg
1000 2000 3000 4000
0 400 800 1200 1600 2000
400
800
1200
1 2 3 4 5
1 1 1
2
3
4
2
3
4
2
3
4
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
2990
2785
2670
2835
3260
3115
3000
3180
3400
3400
3400
3400
0,50
0,50
0,50
0,50
0,64
0,73
0,75
0,72
0,74
0,96
1,05
0,93
2,18
2,30
2,30
2,30
2,81
3,18
3,30
3,15
1,17
149
160
143
87
80
74
78
87
82
77
82
88
83
80
85
=@max.
3
*3G 280 M3G 084-DF P. 94 / P5)
*3G 280 M3G 084-DF P. 94 / P5)
1~200-277 50/60 2670 0,50 2,30 -25..+45 4,2
A
1~200-277 50/60 3000 0,75 3,30 -25..+45 4,9
B
*3G 280 M3G 084-FA P. 95 / P6) 3~380-480 50/60 3400 1,05 1,60 -25..+45 5,4
C
B
C
A
EC centrifugal fans – RadiPac
backward curved, Ø 280
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: PP plastic
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 6
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 55
– Insulation class: "F"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 230 or 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
19
Information
ø 250ø 280ø 310ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 94 f.
– EMC: A B Interference emission according to EN 61000-6-3
C Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
A B C Immunity to interference according to EN 61000-6-2
A B Circuit feedback according to EN 61000-3-2/3
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Cable exit: Variable
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE; A B EN 60335-1
– Approvals: C22.2 Nr.77 + CAN/CSA-E60730-1, UL 1004-7 + 60730
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 280-PR03 -H1
R3G 280-PR04 -I1
4,2
4,9
8,4
9,1
28004-2-4013
28004-2-4013
R3G 280-PS10 -J1 5,4 9,328004-2-4013
K3G 280-PR03 -H2
K3G 280-PR04 -I2
K3G 280-PS10 -J2
ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 94 f.
Inlet ring
P. 82 ff.
Drawings
P. 20 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
20
2016-02
R3G 280-PR03-H1 (Centrifugal fan)
K3G 280-PR03-H2 (Centrifugal module with support bracket)
127 46
8
160
±1.8
Ø164
±0.35
M6 (4x)
4x90°
45°
85
±10
1000
+20
8
Ø150
±0.35
Ø187.5
±0.3
Ø294
Ø280
Ø178
47.7
Ø11 (4x)
298
242.2
±3
85
±10
8
1000
+20
194.5
±2
2
10
1.25
350
400
Max. clearance for screw 16 mm
Cable PVC AWG22,
5x crimped ferrules
Accessory part: Inlet ring 28004-2-4013
Not included in scope of delivery (k-factor: 77)
Dimensions: see “Accessories” chapter
Cable PVC AWG18,
5x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 77)
EC centrifugal fans – RadiPac
backward curved, Ø 280
21
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 280-PR04-I1 (Centrifugal fan)
K3G 280-PR04-I2 (Centrifugal module with support bracket)
127 46
8
160
±1.8
Ø186
±0.5
M6 (4x)
4x90°
45°
85
±10
1000
+20
8
Ø169
±0.35
Ø187.5
±0.3
Ø294
Ø280
Ø200
64.1
Ø11 (4x)
298
258.6
±3
85
±10
8
1000
+20
194.5
±2
2
10
1.25
350
400
Max. clearance for screw 16 mm
Cable PVC AWG22,
5x crimped ferrules
Accessory part: Inlet ring 28004-2-4013
Not included in scope of delivery (k-factor: 77)
Dimensions: see “Accessories” chapter
Cable PVC AWG18,
5x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 77)
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 280
22
2016-02
R3G 280-PS10-J1 (Centrifugal fan)
K3G 280-PS10-J2 (Centrifugal module with support bracket)
127 46
8
175
±1.8
Ø186
±0.5
M6 (4x)
4x90°
45°
85
±10
1000
+20
8
Ø169
±0.35
Ø187.5
±0.3
Ø294
Ø280
Ø200
64.1
Ø11 (4x)
298
273.6
±3
85
±10
8
1000
+20
209.5
±2
2
10
1.25
350
400
Max. clearance for screw 16 mm
Cable PVC AWG22,
5x crimped ferrules
Accessory part: Inlet ring 28004-2-4013
Not included in scope of delivery (k-factor: 77)
Dimensions: see “Accessories” chapter
Cable PVC AWG18,
6x crimped ferrules
Attachment for inlet ring and FlowGrid (4x) Pressure tap (k-factor: 77)
EC centrifugal fans – RadiPac
backward curved, Ø 280
23
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
24
2016-02
qvm³/h
cfm
Pfs Pa
in wg
1000 2000 3000 4000 5000 6000 7000
0 1000 2000 3000 4000
500
1000
1500
2000
2 4 6 8
2
3
4
2
3
4
2
3
4
111
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: A IP 55; B C IP 54
– Insulation class: A "F"; B C "B"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
3010
3010
3010
3010
3410
3410
3410
3410
4000
4000
4000
4000
0,67
1,05
1,23
1,19
1,05
1,54
1,80
1,75
1,41
2,61
2,94
2,95
1,06
1,61
1,90
1,82
1,68
2,40
2,80
2,69
2,66
4,03
4,53
4,60
92
84
78
85
93
86
83
87
102
92
89
92
=@max.
3
*3G 310 M3G 084-GF P. 96 / P8)
*3G 310 M3G 112-GA P. 92 / M3)
3~380-480 50/60 3010 1,23 1,90 -25..+40 7,0
A
3~380-480 50/60 3410 1,80 2,80 -25..+40 10,9
B
*3G 310 M3G 112-GA P. 92 / M3) 3~380-480 50/60 4000 2,95 4,60 -25..+40 10,9
C
C
B
A
EC centrifugal fans – RadiPac
backward curved, Ø 310
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
25
Information
ø 250ø 280ø 310ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 92 f.
– EMC: Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: C22.2 Nr.77 + CAN/CSA-E60730-1, UL 1004-7 + 60730
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 310-PT08 -J1
R3G 310-PH38 -01
7,0
10,9
15,5
18,0
31475-2-4013
31475-2-4013
R3G 310-PH58 -01 10,9 18,031475-2-4013
K3G 310-PT08 -J2
K3G 310-PH38 -02
K3G 310-PH58 -02
ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 26 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
26
2016-02
R3G 310-PT08-J1 (Centrifugal fan)
K3G 310-PT08-J2 (Centrifugal module with support bracket)
98.2
179
6
Ø186
±0.5
255.5
±1.8
Ø169
±0.35
M6 (4x)
4x90°
45°
Ø223.5
+1
Ø360
Ø200
108.5
54.8
Ø350
Ø11 (4x)
372
M20x1.5 M16x1.5 (2x)
Ø4.5 (x4)
408.5
±3
Ø290
300
±2.5
15
4x90°
45°
450
500
Tightening torque
1.5 ± 0.2 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 8 mm, max. 12 mm
Tightening torque 2.5 ± 0.4 Nm
Max. clearance for screw 16 mmAccessory part: Inlet ring 31475-2-4013
Not included in scope of delivery (k-factor: 116)
Dimensions: see “Accessories” chapter
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 116)
Cable gland
M16 x 1.5 (2x):
Cable diameter
min. 6 mm, max. 10 mm
Tightening torque 2.5 ± 0.4 Nm
Cable diameter
min. 4 mm, max. 7 mm
Tightening torque 2.5 ± 0.4 Nm
(included seal must be used)
EC centrifugal fans – RadiPac
backward curved, Ø 310
27
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 310-PH38-01 (Centrifugal fan)
K3G 310-PH38-02 (Centrifugal module with support bracket)
98.2
179
251
6
Ø252
±0.5
Ø275
M10 (6x)
6x60°
Ø360
Ø232
72
Ø223.5
+1
54.8
Ø350
Ø11 (4x)
375
M20x1.5 (3x)
Ø4.5 (x4)
367,5
±3
Ø290 295.5
±2.5
15
4x90°
45°
450
500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 116)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 31475-2-4013
Not included in scope of delivery (k-factor: 116)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 310
28
2016-02
R3G 310-PH58-01 (Centrifugal fan)
K3G 310-PH58-02 (Centrifugal module with support bracket)
98.2
179
251
6
Ø252
±0.5
Ø275
M10 (6x)
6x60°
Ø360
72
Ø223.5
+1
54.8
Ø350
Ø11 (4x)
375
Ø4.5 (x4)
367.5
±3
295.5
±1
15
4x90°
45°
450
500
Ø290
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 116)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 31475-2-4013
Not included in scope of delivery (k-factor: 116)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 310
29
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
30
2016-02
qvm³/h
cfm
Pfs Pa
in wg
2000 4000 6000 8000
0 1000 2000 3000 4000
400
800
1200
1600
2 4 6
1 11 1
2
3
4
2
3
4
2
3
4
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
2400
2400
2400
2400
2870
2870
2870
2870
3230
3230
3230
3230
0,62
0,97
1,10
1,07
1,05
1,58
1,90
1,89
1,48
2,16
2,68
2,56
0,98
1,49
1,70
1,65
1,69
2,46
3,00
2,92
2,30
3,32
4,10
3,94
87
78
76
80
92
85
81
86
93
87
83
87
=@max.
3
*3G 355 M3G 112-EA P. 96 / P8)
*3G 355 M3G 112-GA P. 92 / M3)
3~380-480 50/60 2400 1,10 1,70 -25..+40 8,7
A
3~380-480 50/60 2870 1,90 3,00 -25..+40 13,0
B
*3G 355 M3G 112-IA P. 92 / M3) 3~380-480 50/60 3230 2,68 4,10 -25..+40 15,0
C
B
C
A
EC centrifugal fans – RadiPac
backward curved, Ø 355
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: A IP 55; B C IP 54
– Insulation class: A "F"; B C "B"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
31
Information
ø 250ø 280ø 710ø 800ø 900
2016-02
R3G 355-PJ75 -01
R3G 355-PH49 -01
8,7
13,0
16,4
23,0
35675-2-4013
35675-2-4013
R3G 355-PI93 -01 15,0 26,035675-2-4013
K3G 355-PJ75 -01
K3G 355-PH49 -02
K3G 355-PI93 -02
ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 32 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
– Technical features: See connection diagram P. 92 f.
– EMC: Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: C22.2 Nr.77 + CAN/CSA-E60730-1, UL 1004-7 + 60730
– Efficiency: Ecodesign EU regulation EU 327/2011
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
32
2016-02
R3G 355-PJ75-01 (Centrifugal fan)
K3G 355-PJ75-01 (Centrifugal module with support bracket)
6
252,5
±2
Ø186
±0.5
Ø200
M6 (4x)
4x90°
45°
Ø252.5
+1
Ø405
Ø169
100.5
110.5
199.7
64.4
Ø370
Ø11 (4x)
414
4xØ9
Ø345
406
±3
305.5
±2
15
4x90°
45°
450
500
Tightening torque
1.5 ± 0.2 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 8 mm, max. 12 mm
Tightening torque 2.5 ± 0.4 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 35675-2-4013
Not included in scope of delivery (k-factor: 148)
Dimensions: see “Accessories” chapter
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 148)
Cable gland
M16 x 1.5 (2x):
Cable diameter
min. 6 mm, max. 10 mm
Tightening torque 2.5 ± 0.4 Nm
Cable diameter
min. 4 mm, max. 7 mm
Tightening torque 2.5 ± 0.4 Nm
(included seal must be used)
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 355
33
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 355-PH49-01 (Centrifugal fan)
K3G 355-PH49-02 (Centrifugal module with support bracket)
6
Ø252
272
±2
Ø275
M10 (6x)
6x60°
Ø405
Ø232
Ø252.5
110.5
199.7
72
64.4
Ø370
Ø11 (4x)
417
4xØ9
Ø345
397,5
±3
325.5
±2
15
4x90°
45°
450
500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 148)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 35675-2-4013
Not included in scope of delivery (k-factor: 148)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 355
34
2016-02
R3G 355-PI93-01 (Centrifugal fan)
K3G 355-PI93-02 (Centrifugal module with support bracket)
Ø252.5
+1
110.5
199.7
6
292
±2
Ø252
±0.5
Ø275
M10 (6x)
6x60°
Ø405
Ø232
72
64.4
Ø370
Ø11 (4x)
417
4xØ9
Ø345
417.5
±3
345.5
±2
15
4x90°
45°
450
500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 148)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 35675-2-4013
Not included in scope of delivery (k-factor: 148)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 355
35
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
36
2016-02
qvm³/h
cfm
Pfs Pa
in wg
2000 4000 6000 8000 10000
0 1000 2000 3000 4000 5000 6000
400
800
1200
1600
2 4 6
11
2
3
4
2
3
4
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: A IP 54; B IP 55
– Insulation class: A "B"; B "F"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
A1
A2
A3
A4
B1
B2
B3
B4
2450
2450
2450
2450
2750
2750
2750
2750
1,32
2,21
2,50
2,34
1,85
2,83
3,29
3,35
2,07
3,38
3,80
3,57
2,90
4,35
5,04
5,20
96
85
82
86
100
90
85
86
=@max.
3
*3G 400 M3G 112-IA P. 92 / M3)
*3G 400 M3G 150-FF P. 93 / M5)
3~380-480 50/60 2450 2,50 3,80 -25..+40 14,6
A
3~380-480 50/60 2750 3,35 5,20 -25..+40 20,3
B
B
A
EC centrifugal fans – RadiPac
backward curved, Ø 400
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
37
Information
ø 250ø 280ø 630ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 92 f.
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A C22.2 Nr.77 + CAN/CSA-E60730-1, UL 1004-7 + 60730
B EAC
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 400-PI92 -01
R3G 400-PA27 -71
14,6
20,3
26,0
32,0
40078-2-4013
40078-2-4013
K3G 400-PI92 -02
K3G 400-PA27 -71
ø 310ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 38 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
38
2016-02
R3G 400-PI92-01 (Centrifugal fan)
K3G 400-PI92-02 (Centrifugal module with support bracket)
6
Ø252
317
±2
128.75
225.5 Ø275
M10 (6x)
6x60°
Ø285.2
+1.5
Ø455
Ø232
72
67.7
Ø396
417
Ø440
Ø455
Ø11 (4x)
374
±2
446
±3
15
450
500
4xØ9
4x90°
45°
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 188)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 40078-2-4013
Not included in scope of delivery (k-factor: 188)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 400
39
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 400-PA27-71 (Centrifugal fan)
K3G 400-PA27-71 (Centrifugal module with support bracket)
128.75
225.5
Ø285.2
+1.5
5
Ø252
310
±2
Ø275
M10 (6x)
6x60°
Ø455
Ø232
70
67.7
Ø396
450
4xØ9
Ø440
Ø455
437
368
±2
15
4x90°
35°
492
500
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 188)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 40078-2-4013
Not included in scope of delivery (k-factor: 188)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 400
40
2016-02
qvm³/h
cfm
Pfs Pa
in wg
4000 8000 12000
0 2000 4000 6000 8000
400
800
1200
1600
2 4 6
111
3
4
2
3
4
2
3
42
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: A IP 54; B C IP 55
– Insulation class: A "B"; B C "F"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
1790
1790
1790
1790
2140
2140
2140
2140
2600
2600
2600
2600
1,00
1,53
1,74
1,66
1,71
2,66
2,90
2,76
3,07
4,64
5,25
5,14
1,61
2,38
2,70
2,57
2,69
4,09
4,50
4,25
4,78
7,13
8,00
7,89
91
82
77
82
96
85
81
86
102
92
87
91
=@max.
3
*3G 450 M3G 112-IA P. 92 / M3)
*3G 450 M3G 150-FF P. 93 / M5)
3~380-480 50/60 1730 1,74 2,70 -25..+50 17,0
A
3~380-480 50/60 2140 2,90 4,50 -25..+40 23,5
B
*3G 450 M3G 150-IF P. 92 / M3) 3~380-480 50/60 2600 5,25 8,00 -25..+40 31,0
C
B
C
A
EC centrifugal fans – RadiPac
backward curved, Ø 450
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
41
Information
ø 250ø 280ø 310ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 92 f.
– EMC: C Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
C Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A C22.2 Nr.77 + CAN/CSA-E60730-1, UL 1004-7 + 60730
B EAC
C EAC, UL, CSA
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 450-PI86 -01
R3G 450-PA23 -71
17,0
23,5
32,0
37,0
45075-2-4013
45075-2-4013
R3G 450-PB24 -01 31,0 47,445075-2-4013
K3G 450-PI86 -02
K3G 450-PA23 -71
K3G 450-PB24 -01
ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 42 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
42
2016-02
R3G 450-PI86-01 (Centrifugal fan)
K3G 450-PI86-02 (Centrifugal module with support bracket)
140
5
254
Ø252
Ø275
348
±2
M10 (6x)
6x60°
Ø319.7
+1.5
Ø530
Ø232
70
75.6
Ø480
580
4xØ9
Ø440
Ø530
Ø11 (4x)
412.5
±2
485
±3
15
4x90°
15°
622
630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 240)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 45075-2-4013
Not included in scope of delivery (k-factor: 240)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 450
43
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 450-PA23-71 (Centrifugal fan)
K3G 450-PA23-71 (Centrifugal module with support bracket)
140.2
5
253.6
Ø252
341
±2
Ø275
M10 (6x)
6x60°
Ø319.7
+1.5
Ø530
Ø232
70
75.6
Ø480
580
4xØ9
Ø440
Ø530
Ø11 (4x)
407.5
±2
477
±3
15
4x90°
15°
622
630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 240)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 45075-2-4013
Not included in scope of delivery (k-factor: 240)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 450
44
2016-02
R3G 450-PB24-01 (Centrifugal fan)
K3G 450-PB24-01 (Centrifugal module with support bracket)
140
5
254
Ø324
376
±2
Ø304
M10 (6x)
6x60°
Ø319,7
+1.5
Ø530
Ø280
113
75.6
Ø480
580
4xØ9
Ø440
Ø530
Ø11 (4x)
442.5
±2
556
±3
15
90°
15°
622
630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 240)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 45075-2-4013
Not included in scope of delivery (k-factor: 240)
Dimensions: see “Accessories” chapter
Cable gland
M25 x 1.5:
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 9 ± 0.9 Nm
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 450
45
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
46
2016-02
qvm³/h
cfm
Pfs Pa
in wg
4000 8000 12000 16000
0 2000 4000 6000 8000 10000
400
800
1200
1600
2 4 6
1 1
3
3
4
4
2
2
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 55
– Insulation class: "F"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
=@max.
3
A1
A2
A3
A4
B1
B2
B3
B4
1910
1910
1910
1910
2250
2250
2250
2250
1,98
2,92
3,38
3,45
3,24
4,86
5,70
5,70
3,09
4,49
5,19
5,30
5,05
7,47
9,00
8,74
102
92
86
53
105
95
88
87
*3G 500 M3G 150-FF P. 93 / M5)
*3G 500 M3G 150-IF P. 92 / M3)
3~380-480 50/60 1910 3,45 5,30 -25..+40 24,3
A
3~380-480 50/60 2250 5,70 9,00 -25..+40 32,0
B
B
A
EC centrifugal fans – RadiPac
backward curved, Ø 500
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
47
Information
ø 250ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 92 f.
– EMC: A Interference emission according to EN 61000-6-4
B Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
A B Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A EAC
B EAC, UL, CSA
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 500-PA23 -71
R3G 500-PB33 -01
24,3
32,0
38,7
48,0
64025-2-4013
64025-2-4013
K3G 500-PA23 -71
K3G 500-PB33 -01
ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 48 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
48
2016-02
R3G 500-PA23-71 (Centrifugal fan)
K3G 500-PA23-71 (Centrifugal module with support bracket)
156
5
282
Ø275
373
±2
Ø252
M10 (6x)
6x60°
Ø355
+2
Ø585
Ø232
70
75
Ø470
580
4xØ9
Ø440
Ø585
Ø11 (4x)
438.5
±2
508
±3
15
4x90°
15°
622
630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 281)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 64025-2-4013
Not included in scope of delivery (k-factor: 281)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 500
49
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 500-PB33-01 (Centrifugal fan)
K3G 500-PB33-01 (Centrifugal module with support bracket)
156
5
282
Ø324
408
±2
Ø304
M10 (6x)
6x60°
Ø355
+2
Ø585
Ø280
113
75
Ø470
580
4xØ9
Ø440
Ø585
Ø11 (4x)
473.5
±2
587
±3
15
4x90°
15°
622
630
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 281)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 64025-2-4013
Not included in scope of delivery (k-factor: 281)
Dimensions: see “Accessories” chapter
Cable gland
M25 x 1.5:
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 9 ± 0.9 Nm
Note installed
position!
Install support
struts as illustrated!
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 500
50
2016-02
qvm³/h
cfm
Pfs Pa
in wg
4000 8000 12000 16000 20000
0 2000 4000 6000 8000 10000 12000
400
800
1200
1 2 3 4 5 6
11
3
3
4
4
2
2
=@max.
3A1
A2
A3
A4
B1
B2
B3
B4
1540
1540
1540
1540
1760
1760
1760
1760
1,83
2,81
3,30
3,23
2,79
4,25
5,00
4,79
2,88
4,32
5,10
4,95
4,36
6,52
7,70
7,32
97
88
82
82
101
92
84
87
*3G 560 M3G 150-IF P. 93 / M5)
*3G 560 M3G 150-NA P. 92 / M3)
3~380-480 50/60 1540 3,30 5,10 -25..+40 30,5
A
3~380-480 50/60 1760 5,00 7,70 -25..+40 38,5
B
B
A
EC centrifugal fans – RadiPac
backward curved, Ø 560
– Material: Support bracket: Steel, painted black
Support plate and inlet ring: Sheet steel, galvanized
Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 55
– Insulation class: "F"
– Installation position: Shaft horizontal or rotor on bottom, rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
Curves:
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
n
rpm
Ped
kW
I
A
LWA
dB(A)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type Motor
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
51
Information
ø 250ø 710ø 800ø 900
2016-02
– Technical features: See connection diagram P. 92 f.
– EMC: Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A EAC
B EAC, UL, CSA
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 560-PB31 -71
R3G 560-PC04 -01
30,5
38,5
52,0
68,0
64030-2-4013
64030-2-4013
K3G 560-PB31 -71
K3G 560-PC04 -01
ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 52 ff.
Centrifugal fan kg kg
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
52
2016-02
R3G 560-PB31-71 (Centrifugal fan)
K3G 560-PB31-71 (Centrifugal module with support bracket)
175
82
6
314
Ø275
432.5
±2
Ø252
M10 (6x)
6x60°
Ø398.2
+2
Ø655
Ø515
Ø232
70
750
4xØ9
Ø545
Ø655
Ø11 (4x)
504.5
±2
574
±3
15
4x90°
15°
792
800
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 348)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 25 mmAccessory part: Inlet ring 64030-2-4013
Not included in scope of delivery (k-factor: 348)
Dimensions: see “Accessories” chapter
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 560
53
Information
ø 250ø 280ø 310ø 630ø 710ø 800ø 900
2016-02
ø 355ø 400ø 450ø 500ø 560
R3G 560-PC04-01 (Centrifugal fan)
K3G 560-PC04-01 (Centrifugal module with support bracket)
175
82
6
314
Ø324
472
±2
Ø304
M10 (6x)
6x60°
Ø398.2
+2
Ø655
Ø515
Ø280
113
750
4xØ9
Ø545
Ø655
Ø11 (4x)
544.5
±2
658
±3
15
4x90°
15°
792
800
Attachment for FlowGrid (4x)
Pressure tap (k-factor: 348)
Tightening torque
3.5 ± 0.5 Nm
Cable gland
M20 x 1.5:
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance for screw 20 mmAccessory part: Inlet ring 64030-2-4013
Not included in scope of delivery (k-factor: 348)
Dimensions: see “Accessories” chapter
Cable gland
M25 x 1.5:
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 9 ± 0.9 Nm
Note installed
position!
Install support
struts as illustrated!
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 560
5000 10000 15000 20000 25000
0
400
800
1,6
200
0,8
600
2,4
1000
4,0
1800
7,23,2
1200
4,8
1400
5,6
1600
6,4
10000 12000 140002000 4000 6000 8000 cfm
qV
Pfs Pa
m3/h
in wg
4
3
2
111
2
3
4
4
3
2
Motor
*3G 630 M3G 150-NA P. 92 / M3)
*3G 630 M3G 200-HF P. 92 / M3)
3~380-480 50/60 1130 2,90 4,50 -25..+55 40
A
3~380-480 50/60 1500 6,75 10,3 -25..+50 125
B
– Material: B C Cube design with inlet ring: Sheet steel, galvanized
and coated with light gray plastic (RAL 7035)
Impeller: Sheet aluminium; Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: A IP 55; B C IP 54 (according to EN 60529)
– Insulation class: "F"
– Installation position: Shaft horizontal ( B C base mounting only) or rotor on bottom;
rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
*3G 630 M3G 200-QA 3~380-480 50/60 1850 11,0 17,0 -25..+40 160
C
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
1130
1130
1130
1130
1500
1500
1500
1500
1850
1850
1850
1850
2,16
2,83
2,90
2,46
4,52
5,76
6,75
6,33
7,46
10,0
11,0
9,89
3,26
4,30
4,50
3,73
7,00
8,87
10,3
9,69
11,6
15,4
17,0
15,2
88
81
78
79
97
92
88
88
101
96
91
92
54
2016-02
B
C
A
=@max.
3
EC centrifugal fans – RadiPac
backward curved, Ø 630
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: n
rpm
Ped
kW
I
A
LWA
dB(A)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
– Technical features: See connection diagram P. 92 f.
– EMC: B C Interference emission according to EN 61000-6-4
B C Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A C UL, CSA, EAC
B EAC
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 630-AP01 -01
---
kg
40,0
---
kg
77,5
---
64040-2-4013
---
--- --- ------
55
2016-02
K3G 630-AP01 -01
---
---
kg
---
125
160
Centrifugal module
with cube design
---
K3G 630-AR02 -01
K3G 630-AS05 -01
Spring elements /
vibration-absorbing
elements P. 88 f.
Conn. diagram
P. 92
Inlet ring
P. 82 ff.
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
Drawings
P. 56 f.
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Centrifugal fan
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
Weight centrifugal
module with
cube design
R3G 630-AP01-01 (Centrifugal fan)
K3G 630-AP01-01 (Centrifugal module with support bracket)
6x60°
6xM10
Ø232
Ø252
Ø275
±2
+3.6
318.3
224 6
Ø444
Ø716
Ø634
98.5
359
70
o652
o800
o750±1
Ø11 (8x)
439 ±2.5 20
508 ±3
Max. clearance for screw 25 mm
56
2016-02
Tightening torque
3.5 ± 0.5 Nm
Cable gland M20 x 1.5 (3x)
Accessory part: Inlet ring 64040-2-4013
Not included in scope of delivery (k-factor: 438)
Dimensions: see “Accessories” chapter
Cable gland
M20 x 1.5 (3x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Pressure tap (k-factor: 438)
Note installed
position!
Install support
struts as illustrated!
EC centrifugal fans – RadiPac
backward curved, Ø 630
K3G 630-AR02-01 (Centrifugal module with cube design)
K3G 630-AS05-01 (Centrifugal module with cube design)
M20x1.5 (2x) M25x1.5
*674
4xØ11
8xØ11
760
660
*159 *451
652.5
511.5
20
506
666
4xØ11
*169 *500
*674
4xØ11 660
760
8xØ11
20
570
711
M20x1.5 (2x) M25x1.5
506
4xØ11
666
57
2016-02
Inlet ring with pressure tap (k-factor: 438) Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 6 ± 0.9 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
Inlet ring with pressure tap (k-factor: 438) Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 6 ± 0.6 Nm
Cable diameter
min. 16 mm, max. 20.5 mm
Tightening torque 6 ± 0.6 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 630
58
2016-02
5000 10000 15000 20000 25000 30000
0
400
800
1,6
200
0,8
600
2,4
1000
4,03,2
1200
4,8
1400
5,6
1600
6,4
10000 150005000 cfm
qV
Pfs Pa
m3/h
in wg
1 1 1
4
3
2
4
3
4
3
2
2
Motor
*3G 710 M3G 150-NA
*3G 710 M3G 200-LA
3~380-480 50/60 920 2,80 4,30 -25..+40 44
A
3~380-480 50/60 1300 7,86 12,0 -25..+40 163
B
*3G 710 M3G 200-QA 3~380-480 50/60 1550 11,8 18,0 -25..+40 194
C
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
920
920
920
920
1300
1300
1300
1300
1550
1550
1550
1550
1,82
2,52
2,80
2,57
5,12
6,91
7,86
7,37
7,63
10,4
11,8
11,1
2,72
3,77
4,30
3,82
7,87
10,6
12,0
11,2
11,9
16,0
18,0
17,1
84
80
78
78
96
91
86
87
101
94
88
91
B
C
A
=@max.
3
EC centrifugal fans – RadiPac
backward curved, Ø 710
– Material: B C Cube design with inlet ring: Sheet steel, galvanized
and coated with light gray plastic (RAL 7035)
Impeller: Sheet aluminium; Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: A IP 55; B C IP 54 (according to EN 60529)
– Insulation class: "F"
– Installation position: Shaft horizontal ( B C base mounting only) or rotor on bottom;
rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
P. 92 / M3)
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: n
rpm
Ped
kW
I
A
LWA
dB(A)
59
2016-02
– Technical features: See connection diagram P. 92
– EMC: A Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
B C Interference emission according to EN 61000-6-4
Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A C UL, CSA, EAC
B EAC
– Efficiency: Ecodesign EU regulation EU 327/2011
R3G 710-AP02 -01
---
kg
44,0
---
kg
92,0
---
71075-2-4013
---
--- --- ------
K3G 710-AP02 -01
---
---
kg
---
163
194
---
K3G 710-AR03 -01
K3G 710-AS06 -01
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Centrifugal module
with cube design
Centrifugal fan
Weight
centrifugal fan
Weight centrifugal
module with
support bracket
Inlet ring with one
pressure tap Centrifugal module
with support bracket
Weight centrifugal
module with
cube design
Spring elements /
vibration-absorbing
elements P. 88 f.
Conn. diagram
P. 92
Inlet ring
P. 82 ff.
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
Drawings
P. 60 f.
60
2016-02
R3G 710-AP02-01 (Centrifugal fan)
K3G 710-AP02-01 (Centrifugal module with support bracket)
600±1
o880±1
Ø11 (12x)
o783
o960
490±2.5
559±3
25
Pressure tap (k-factor: 545)
Note installed
position!
Install support
struts as illustrated!
Ø232
Ø252
Ø275
±2
+4.6
354
250 15
Ø501
Ø806
Ø720
117
394
70
6x60°
6xM10
Max. clearance for screw 25 mm
Tightening torque
3.5 ± 0.5 Nm
Cable gland M20 x 1.5 (3x)
Accessory part: Inlet ring 71075-2-4013
Not included in scope of delivery (k-factor: 545)
Dimensions: see “Accessories” chapter
Cable gland
M20 x 1.5 (3x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
EC centrifugal fans – RadiPac
backward curved, Ø 710
61
2016-02
K3G 710-AR03-01 (Centrifugal module with cube design)
K3G 710-AS06-01 (Centrifugal module with cube design)
4xØ11
*234 *337
*884
20xØ11
600
750
880
960
25
579.5
712.5
M20x1.5 (2x)
M25x1.5
700
864
4xØ11
600
750
880
960
20xØ11
25 621
759
*884 *252.5 *405
4xØ11
M20x1.5 (2x) M25x1.5
700
4xØ11
864
Inlet ring with pressure tap (k-factor: 545) Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 6 ± 0.9 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
Inlet ring with pressure tap (k-factor: 545)
Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 6 ± 0.6 Nm
Cable diameter
min. 16 mm, max. 20.5 mm
Tightening torque 6 ± 0.6 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 710
62
2016-02
5000 10000 15000 20000 25000 30000 35000
0
400
800
1,6
200
0,8
600
2,4
1000
4,03,2
1200
4,8
1400
5,6
1600
6,4
10000 15000 200005000 cfm
qV
Pfs Pa
m3/h
in wg
4
1 1
2
3
4
3
2
Motor
K3G 800-AR08 -01 M3G 200-QA
K3G 800-AS07 -01 M3G 200-QA
3~380-480 50/60 1050 7,53 11,6 -25..+40 189
A
3~380-480 50/60 1370 11,6 17,8 -25..+40 196
B
– Material: Cube design with inlet ring: Sheet steel, galvanized
and coated with light gray plastic (RAL 7035)
Impeller: Sheet aluminium; Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 54 (according to EN 60529)
– Insulation class: "F"
– Installation position: Shaft horizontal (base mounting only) or rotor on bottom;
rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
A1
A2
A3
A4
B1
B2
B3
B4
1050
1050
1050
1050
1370
1370
1370
1370
4,91
6,56
7,53
7,18
6,76
9,62
11,6
10,7
7,58
10,1
11,6
11,0
10,5
14,8
17,8
16,4
94
88
85
85
106
98
90
93
A
B=@max.
3
EC centrifugal fans – RadiPac
backward curved, Ø 800
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: n
rpm
Ped
kW
I
A
LWA
dB(A)
63
2016-02
– Technical features: See connection diagram P. 92
– EMC: Interference emission according to EN 61000-6-4
Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A EAC
B UL, CSA, EAC
– Efficiency: Ecodesign EU regulation EU 327/2011
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Spring elements /
vibration-absorbing
elements P. 88 f.
Conn. diagram
P. 92
Inlet ring
P. 82 ff.
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
Drawings
P. 64 f.
64
2016-02
K3G 800-AR08-01 (Centrifugal module with cube design)
4xØ11
*251.5 *430
*884
20xØ11
600
750
880
960
25
650
783
M20x1.5 (2x) M25x1.5
4xØ11
700
864
Inlet ring with pressure tap (k-factor: 695) Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 6 ± 0.9 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
EC centrifugal fans – RadiPac
backward curved, Ø 800
65
2016-02
K3G 800-AS07-01 (Centrifugal module with cube design)
600
750
880
960
20xØ11
25
621
759
*884 *252.5 *405
4xØ11
M20x1.5 (2x) M25x1.5
700
864
4xØ11
Inlet ring with pressure tap (k-factor: 695) Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 6 ± 0.6 Nm
Cable diameter
min. 16 mm, max. 20.5 mm
Tightening torque 6 ± 0.6 Nm
* Anschraubposition für Schwing-
bzw. Federelemente,
bei horizontaler Wellenlage
nur Bodenmontage erlaubt.
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 800
66
2016-02
5000 10000 15000 20000 25000 30000 35000
0
400
800
1,6
200
0,8
600
2,4
1000
4,03,2
1200
4,8
10000 15000 200005000 cfm
qV
Pfs Pa
m3/h
in wg
1 1
2
3
4
4
3
2
Motor
K3G 900-AR10 -01 M3G 200-QA
K3G 900-AS08 -01 M3G 200-QA
3~380-480 50/60 860 7,52 11,5 -25..+40 222
A
3~380-480 50/60 1050 8,70 13,5 -25..+40 232
B
A1
A2
A3
A4
B1
B2
B3
B4
860
860
860
860
1050
1050
1050
1050
5,03
6,75
7,52
7,02
5,04
7,33
8,70
7,74
7,72
10,3
11,5
10,7
8,03
11,4
13,5
12,0
92
87
82
81
99
91
86
87
A
B
=@max.
3
EC centrifugal fans – RadiPac
backward curved, Ø 900
– Material: Cube design with inlet ring: Sheet steel, galvanized
and coated with light gray plastic (RAL 7035)
Impeller: Sheet aluminium; Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 54 (according to EN 60529)
– Insulation class: "F"
– Installation position: Shaft horizontal (base mounting only) or rotor on bottom;
rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: n
rpm
Ped
kW
I
A
LWA
dB(A)
67
2016-02
– Technical features: See connection diagram P. 92
– EMC: A Interference emission according to EN 61000-6-4
A Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (with customer connection of protective earth)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A EAC
B UL, CSA, EAC
– Efficiency: Ecodesign EU regulation EU 327/2011
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Spring elements /
vibration-absorbing
elements P. 88 f.
Conn. diagram
P. 92
Inlet ring
P. 82 ff.
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
Drawings
P. 68 f.
68
2016-02
K3G 900-AR10-01 (Centrifugal module with cube design)
4xØ11
*1104 *440
*203.5
24xØ11
400
800
950
1100
1180
30
612
745
M20x1.5 (2x) M25x1.5
4xØ11
930
1084
Inlet ring with pressure tap (k-factor: 900)
Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Cable diameter
min. 9 mm, max. 16 mm
Tightening torque 6 ± 0.9 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
EC centrifugal fans – RadiPac
backward curved, Ø 900
69
2016-02
K3G 900-AS08-01 (Centrifugal module with cube design)
4xØ11
*181 *375
*1104 400
800
950
1100
1180
24xØ11
30 519
657
M25x1.5
M20x1.5 (2x)
4xØ11
930
1084
Inlet ring with pressure tap (k-factor: 900)
Tightening torque
3.5 ± 0.5 Nm
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 6 ± 0.6 Nm
Cable diameter
min. 16 mm, max. 20.5 mm
Tightening torque 6 ± 0.6 Nm
* Mounting position for vibration-
absorbing and spring elements,
only floor mounting allowed for
horizontal shaft position.
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 900
1000 2000 3000 4000 5000 6000
7000 8000 9000
0
200
400
0,8 1,6
600
2,4
800
3,2
1000
4,0
1200
4,8
1400
5,6
500 1000 1500 2000 3000 3500 4000 4500 5000 55002500 cfm
qV
Pfs Pa
m3/h
in wg
4
3
3
2
2
1 1 1 1 1
2
2
33
4
4
4
4
3
2
Motor
R3G 280-AJ14 -C1 M3G 084-GF
R3G 310-BC38 -01 M3G 112-GA
3~380-480 50/60 3260 0,99 1,60 -25..+60 6,8
A
3~380-480 50/60 3170 1,65 2,50 -25..+50 12,1
B
– Material: Impeller: Sheet aluminium
Rotor: Painted black
Electronics housing: Die-cast aluminium
– Number of blades: 7
– Direction of rotation: Clockwise viewed toward rotor
– Degree of protection: IP 54
– Insulation class: "B"
– Installation position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensation drainage holes: Rotor side
– Mode: Continuous operation (S1)
– Mounting: Maintenance-free ball bearings
R3G 355-BD43 -01 M3G 112-GA 3~380-480 50/60 2650 1,73 2,60 -25..+60 12,6
C
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
3260
3260
3260
3260
3170
3170
3170
3170
2650
2650
2650
2650
0,70
0,88
0,99
0,87
1,23
1,52
1,65
1,54
1,25
1,56
1,73
1,63
1,31
1,57
1,60
1,57
1,83
2,27
2,50
2,30
1,86
2,33
2,60
2,42
89
86
84
85
90
88
85
88
90
86
84
86
70
2016-02
=@max.
3
R3G 400-AS23 -01 M3G 150-FF P. 92 / M3) 3~380-480 50/60 2550 2,84 4,20 -25..+60 21,3
D
R3G 450-AS24 -01 M3G 150-FF P. 92 / M3) 3~380-480 50/60 2040 2,38 3,60 -25..+60 22,0
E
D1
D2
D3
D4
E1
E2
E3
E4
2550
2550
2550
2550
2040
2040
2040
2040
2,10
2,59
2,84
2,68
1,64
2,16
2,38
2,17
3,13
3,84
4,20
3,95
2,48
3,23
3,60
3,24
92
89
86
89
90
85
82
86
BC
A D
E
EC centrifugal fans – RadiPac
backward curved, Ø 280 - 450 (compact design)
P. 97 / L6)
P. 92 / M3)
P. 92 / M3)
Subject to change (1) Nominal data at operating point with maximum load and 400 VAC.
Type
Nominal data
Techn. features
and connection
diagram
VAC Hz rpm kW A °C kg
Curve
Nominal voltage
range
Frequency
Speed(1)
Max.
Input power(1)
Max.
Input current(1)
Weight
Perm. ambient temp.
Air performance measured according to: ISO 5801, installation category A, with ebm-papst inlet ring without contact protection.
Intake-side sound level: LwA according to ISO 13347, LpA measured at 1 m distance from fan axis. The values given are only ap-
plicable under the specifi ed measuring conditions and may differ depending on the installation conditions. In the event of deviation
from the standard confi guration, the parameters must be checked in installed condition. See Page 98 ff for detailed information.
Curves: n
rpm
Ped
kW
I
A
LWA
dB(A)
– Technical features: See connection diagram P. 92 f.
– EMC: D Interference emission according to EN 61000-6-3,
except EN 61000-3-2 for professionally used equipment
with a total rated power greater than 1 kW
D Immunity to interference according to EN 61000-6-2
– Touch current: <= 3,5 mA according to IEC 60990 (measuring circuit Fig. 4)
– Terminal box design: electrical connection via terminal strip
– Protection class: I (if protective earth is connected by customer to the housing‘s connection point)
– Conformity with standards: EN 61800-5-1, CE
– Approvals: A C22.2 Nr.77 + CAN/CSA-E60730-1, EAC, UL 1004-7 + 60730
B C VDE, EAC
D E UL, CSA, EAC
– Efficiency: Ecodesign EU regulation EU 327/2011
71
2016-02
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
Conn. diagram
P. 92 f.
Inlet ring
P. 82 ff.
Drawings
P. 72 f.
FlowGrid air-inlet guard
/ intake finger guard
P. 80 f.
R3G 280-AJ14-C1 (Centrifugal fan)
72
2016-02
5x72°
M6 (5x)
152.4±2
56.5
Ø165±0.25
+1.8
0
Ø197
90
126
Ø197.4
Ø284
Ø187.2
Ø193.4
4x Ø4.5
4x Ø4.5
53
Ø260
Ø280
Ø325
Ø186±0,5
61.5
Max. clearance
for screw 16 mm
Tightening torque
3.5 ± 0.5 Nm
Accessory part: Inlet ring 28075-2-4013
Not included in scope of delivery (k-factor: 93)
Cable gland
M16 x 1.5 (3x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 2.5 ± 0.4 Nm
6xM10
Ø252±0.5
Ø232
6x60°
100
147 6
Ø319
Ø222
60 170.2 ±2
54.8
Ø350
+2
6xM10
Ø252±0.5
Ø232
6x60°
112
164 6
Ø360
Ø250.3
60 187.2 ±2
64.4
Ø370
+2.3
Max. clearance
for screw 20 mm
Tightening torque
3.5 ± 0.5 Nm
Accessory part: Inlet ring 31475-2-4013
Not included in scope of delivery (k-factor: 116)
Dimensions: see “Accessories” chapter
Cable gland
M20 x 1.5 (3x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance
for screw 20 mm
Tightening torque
3.5 ± 0.5 Nm
Accessory part: Inlet ring 35675-2-4013
Not included in scope of delivery (k-factor:: 148)
Dimensions: see “Accessories” chapter
Cable gland
M20 x 1.5 (3x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
EC centrifugal fans – RadiPac
backward curved, Ø 280 - 450 (compact design)
R3G 310-BC38-01 (Centrifugal fan)
R3G 355-BD43-01 (Centrifugal fan)
73
2016-02
R3G 400-AS23-01 (Centrifugal fan)
R3G 450-AS24-01 (Centrifugal fan)
±3
±2
8x45°
22.5°
6x60°
14xM10
Ø232-2
Ø252±0,3
Ø275
220.5±1
182
125 9
Ø282
Ø404
Ø413
67.7
228.5
289.5
70
±3
±2
8x45°
22.5°
6x60°
14xM10
Ø232-2
Ø252±0,3
Ø275
220.5±1
204
140 9
Ø317
Ø455
Ø480
75.6
250.2
320.2
70 Max. clearance
for screw 25 mm
Tightening torque
3.5 ± 0.5 Nm
Accessory part: Inlet ring 45075-2-4013
Not included in scope of delivery (k-factor: 240)
Dimensions: see “Accessories” chapter
Cable gland
M20 x 1.5 83x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Max. clearance
for screw 25 mm
Tightening torque
3.5 ± 0.5 Nm
Accessory part: Inlet ring 40078-2-4013
Not included in scope of delivery (k-factor: 188)
Dimensions: see “Accessories” chapter
Cable gland
M20 x 1.5 83x):
Cable diameter
min. 4 mm, max. 10 mm
Tightening torque 4 ± 0.6 Nm
Information
ø 250ø 710ø 800ø 900 ø 280ø 310ø 630 ø 355ø 400ø 450ø 500ø 560
Compact designTechnologyAgents
EC centrifugal fans – RadiPac
backward curved, Ø 280 - 450 (compact design)
74
2016-02
Tender specifications
Fan size 250 to 560
Direct-drive single inlet centrifugal fans with backwards-curved high-performance centrifugal impellers with radial diffusers,
mounted on a GreenTech EC external rotor motor with integrated control electronics.
Impeller made of aluminum, with 5 backwards-curved,
continuously welded, hollow-profile blades; impeller sizes 250
and 280 made of plastic; flow-optimized inlet ring made of
galvanized sheet steel with pressure test nipple.
Motor impeller statically and dynamically balanced on two planes
to balancing grade G 6.3 in accordance with DIN ISO 1940.
GreenTech EC external rotor motor surpasses efficiency class IE4,
magnets with no rare earths, maintenance-free ball bearings with
long-term lubrication, theoretical nominal service life of at least
40,000 hours of operation.
Soft start, integrated current limitation, extended voltage input
1~200-277 V, 50/60 respectively 3~380-480 V, 50/60 Hz. Fan
can be used with all standard power supply networks with
unaltered air performance.
Integrated electronics, low-noise commutation logic; 100 %
open-loop speed control; all fans have an RS485/MODBUS RTU
interface, and do not need to be installed with shielded cables.
All 1~ types have an integrated active PFC (Power Factor
Correction) to reduce disturbing harmonic content.
Terminal box made of aluminum with easily accessible connec-
tion area with spring-loaded terminals, environment-resistant
cable glands, or with external variable cable (sizes 250 to 280).
Any work required for isolation from structure-borne noise to be
performed by the customer.
Fan satisfies the applicable EMC guidelines and requirements
with regard to circuit feedback (for specific information, see the
respective data sheet).
Documentation and marking conform to the applicable
EU Directives.
Reliable performance data, air performance measurements on
intake-side chamber test rig according to ISO 5801 and
DIN 24163, noise measurements in anechoic rooms according
to DIN EN ISO 3745.
Integrated protective devices:
- Alarm relay with zero-potential change-over contacts
(250 V AC/2 A, cos O = 1)
- Locked-rotor protection
- Phase failure detection
- Soft start of motors
- Mains under-voltage detection
- Thermal overload protection for electronics and motor
- Short circuit protection
Optional:
- Other and specific requirements on request
75
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
2016-02
Compact designTechnologyAgents
Technical data:
Fan type = __ __ __ __ __ __ - __ __ __ __ - __ __
Air flow qV = _________________________________ m3/h, cfm
Stat. pressure increase pfs = _________________________________ Pa, in wg
Stat. overall efficiency @es = _________________________________ %
Operating speed n = _________________________________ rpm
Motor type = EC-Motor
Type of control = Closed-loop speed control, 0-100 %
Motor efficiency class = IE4
Total power input Ped = _________________________________ kW
Specific fan power SFP = _________________________________ kW/(m3/s)
Nominal voltage range UN = _________________________________ V
Line frequency f = 50 / 60 Hz
Nominal current IN = _________________________________ A
Protection class = IP54
Sound power level LWA (A, in) = __________ / LWA (A, out) = __________ dB(A)
Sound pressure level (at 1 m) LPA (A, in) = __________ / LPA (A, out) = __________ dB(A)
Perm. ambient temperature T = _______________ bis _______________ °C
Weight of fan m = _________________________________ kg
See data sheet for dimensions and connections.
76
2016-02
Tender specifications
Fan size 630 to 900
Direct-drive single inlet centrifugal fans with backwards-curved high-performance centrifugal impellers with radial diffusers,
mounted on a GreenTech EC external rotor motor with integrated control electronics.
Impeller made of aluminum, with 7 backwards-curved,
continuously welded blades; flow-optimized inlet ring made
of galvanized sheet steel with pressure test nipple.
Motor impeller statically and dynamically balanced on two planes
to balancing grade G 6.3 (motor size 200 to balancing grade
G 4.0) in accordance with DIN ISO 1940.
GreenTech EC external rotor motor surpasses efficiency class IE4,
magnets with no rare earths, maintenance-free ball bearings with
long-term lubrication, theoretical nominal service life of at least
40,000 hours of operation.
Soft start, integrated current limitation, extended voltage input
3~380-480 V, 50/60 Hz. Fan can be used with all standard
power supply networks with unaltered air performance.
Integrated electronics, low-noise commutation logic; 100 %
open-loop speed control; all fans have an RS485/MODBUS RTU
interface, and do not need to be installed with shielded cables.
Terminal box made of aluminum with easily accessible connec-
tion area with spring-loaded terminals, environment-resistant
cable glands.
Any work required for isolation from structure-borne noise to be
performed by the customer.
Fan satisfies the applicable EMC guidelines and requirements
with regard to circuit feedback (for specific information, see the
respective data sheet).
Documentation and marking conform to the applicable
EU Directives.
Reliable performance data, air performance measurements on
intake-side chamber test rig according to ISO 5801 and
DIN 24163, noise measurements in anechoic rooms according
to DIN EN ISO 3745
Integrated protective devices:
- Alarm relay with zero-potential change-over contacts
(250 V AC/2 A, cos O = 1)
- Locked-rotor protection
- Phase failure detection
- Soft start of motors
- Mains under-voltage detection
- Thermal overload protection for electronics and motor
- Short circuit protection
Optional:
- Other and specific requirements on request
77
2016-02
Technical data:
Fan type = __ __ __ __ __ __ - __ __ __ __ - __ __
Air flow qV = _________________________________ m3/h, cfm
Stat. pressure increase pfs = _________________________________ Pa, in wg
Stat. overall efficiency @es = _________________________________ %
Operating speed n = _________________________________ rpm
Motor type = EC-Motor
Type of control = Closed-loop speed control, 0-100 %
Motor efficiency class = IE4
Total power input Ped = _________________________________ kW
Specific fan power SFP = _________________________________ kW/(m3/s)
Nominal voltage range UN = _________________________________ V
Line frequency f = 50 / 60 Hz
Nominal current IN = _________________________________ A
Protection class = IP54
Sound power level LWA (A, in) = __________ / LWA (A, out) = __________ dB(A)
Sound pressure level (at 1 m) LPA (A, in) = __________ / LPA (A, out) = __________ dB(A)
Perm. ambient temperature T = _______________ bis _______________ °C
Weight of fan m = _________________________________ kg
See data sheet for dimensions and connections.
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
78
2016-02
79
2016-02
Accessories
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
Would you like
to find out more?
If you need an
installation guide
or more information
about the dimensions,
go to:
www.ebmpapst.com
/flowgrid-manual
or scan the
QR code below:
80
ebm-papst fans are not measured on our own advanced test stands just for their air
performance alone. The acoustic behavior of the fans is also examined and the
measurement results are included in the technical documentation.
Please note that the measurements are taken under ideal conditions with undisturbed
infl ow and outfl ow. If the fans are subsequently installed and used in devices with rather
tight spaces, it is to be expected that the noise data provided in the documentation will
not be applicable.
In order to minimize the negative impact of the installation situation, ebm-papst offers
the FlowGrid air-inlet guard shown here. It is installed on the intake side of the fan and
effectively reduces the noise generated by the fan. Particularly annoying, low-frequency
noises are reduced effi ciently. The level of noise reduction is dependent on the installation
situation, which is why no generally applicable data is possible here.
ØC H
S
ØB
E
2016-02
Part number
20280-2-2957
FlowGrid air inlet grill Dimensions (mm)
ØB ØC ØE S H N*
280 245-261 4,5 3,5 40 20,5 Nm
Fan size
250, 280
25310-2-2957 315 288-292 5,5 3,5 49 20,5 Nm310
00400-2-2957 370 334-346 4,5 3,5 56 20,5 Nm355
35505-2-2957 470 440 9,0 3,5 71 102 Nm 400, 450, 500
00630-2-2957 580 545 10 3,0 90 102 Nm 560, 630
50710-2-2957 666 630 10 3,0 106 102 Nm710
63000-2-2957 785 750 10 3,0 125 102 Nm800
80000-2-2957 995 960 10 3,5 131 102 Nm900
FlowGrid air inlet grill
Effi cient noise reduction
Subject to change * Recommended tightening torque for fastening screws
81
Intake fi nger guard
Wire mesh fi nger guard
– Material: Steel wire, phosphated,
Versions 1 and 2: Painted pebble gray (RAL 7032)
Versions 3 and 4: Painted light gray (RAL 7035)
Subject to change
Part number
79280-2-4039
Intake fi nger guard for backwards-curved centrifugal fans (according to EN ISO 13857)
a b d e Strut division Dimensions (mm)
280 4,5 227 2,8 4 x 90°
Fan size
250, 280
2016-02
Version
1
79310-2-4039 325 4,5 271 2,8 4 x 90°310 1
79355-2-4039 345 4,5 308 2,8 4 x 90°355 1
79400-2-4039 390 8,5 343 2,8 3 x 120°400 2
79450-2-4039 430 8,5 381 2,8 3 x 120°450 2
79500-2-4039 445 8,5 417 2,8 3 x 120°500 2
79560-2-4039 490 8,5 466 2,8 3 x 120°560 2
79630-2-4039 600 8,5 551 3,9 3 x 120°630 3
79710-2-4039 700 8,5 651 3,9 3 x 120°710, 800 3
79900-2-4039 850 8,5 801 3,9 6 x 60°900 4
Ød
Øa
b
e
Version 1 Version 2
e
Ød
Øa
b
Ød
Øa
eb
b
Ød
Øa
e
Version 3 Version 4
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
82
2016-02
Inlet rings
With / without measuring device
– Material: Galvanized sheet steel
Part number
96350-2-4013(1) / 96355-2-4013(2) / 96345-2-4013(3)
Inlet rings with / without measuring device to determine the air fl ow for backwards-curved centrifugal fans
Fan size
250
28000-2-4013(1) / 28004-2-4013(2) / 28003-2-4013(3) 280
31470-2-4013(1) / 31475-2-4013(2) / 31480-2-4013(3) 310
35670-2-4013(1) / 35675-2-4013(2) / 35680-2-4013(3) 355
40073-2-4013(1) / 40078-2-4013(2) / 40083-2-4013(3) 400
45070-2-4013(1) / 45075-2-4013(2) / 45080-2-4013(3) 450
63072-2-4013(1) / 64025-2-4013(2) / 64002-2-4013(3) 500
63071-2-4013(1) / 64030-2-4013(2) / 64001-2-4013(3) 560
63070-2-4013(1) / 64040-2-4013(2) / 64000-2-4013(3) 630
71070-2-4013(1) / 71075-2-4013(2) / 71080-2-4013(3) 710
Dimensions / drawing
see page 89
see page 89
see page 89
see page 89
see page 89
see page 89
see page 90
see page 90
see page 91
see page 91
Subject to change (1) Without measuring device (2) With one pressure tap (3) With piezometer
(2) With one
pressure tap:
(3) With
piezometer:
28070-2-4013(1) / 28075-2-4013(2) / 28080-2-4013(3) 280 (compact) see page 76
(1) Without
measuring device:
83
Inlet rings
Dimensioned drawings with one pressure tap
2016-02
Baugröße 250 Baugröße 280
R18
R55.5
R35
Ø161.3
Ø167.25
Ø280
1.5
48
Ø4.5 (4x)
Ø5 (6x)
15°
6x60°
Ø250
Ø260
Ø260
Ø4,5
4x90°
Ø280
Ø176,7
Ø182
46
1,25
R17
R53
R33
Baugröße 250: Baugröße 280:
Baugröße 250 Baugröße 280
R20,5
R63,5
R58
Ø290
Ø325
Ø4,5
Ø4,5
1,5
54,8
Ø211,7
Ø217
Ø350
Ø345
Ø4,5
Ø370
1,5
64,4
Ø239
Ø246
R24
R74,5
R47
Fan size 310: Fan size 355:
Baugröße 250 Baugröße 280
R18
R55.5
R35
Ø161.3
Ø167.25
Ø280
1.5
48
Ø4.5 (4x)
Ø5 (6x)
15°
6x60°
Ø250
Ø260
Ø260
Ø4,5
4x90°
Ø280
Ø176,7
Ø182
46
1,25
R17
R53
R33
Fan size 250: Fan size 280:
Baugröße 250 Baugröße 280
Ø376
1,5
67,7
Ø396
Ø270,9
Ø278
R25,5
R78,5
R49,5
Ø9(6x)
Ø4,5(6x)
30°
6x60°
6x60°
392(3x)
R28
R87,5
R55
2
75,6
Ø480
Ø303,4
Ø312
Ø430
Ø440
Ø460
9
Ø10(4x)
45°
4x90°
6x60°
Fan size 400: Fan size 450:
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
84
2016-02
Inlet rings
Dimensioned drawings with one pressure tap
R28
R87
R49
2
75
Ø470
Ø337
Ø346
Ø440
Ø445
Ø9(6x)
Ø9(4x)
6x60°
45°
15°
4x90°
R30
R95
R60
2
82
Ø515
Ø380
Ø388,8
Ø9(6x)
6x60°
15°
Ø490
505
Fan size 560:
Fan size 500:
85
2016-02
R37
R14
R72
2
98,5
Ø634
Ø427
Ø436,8
Ø545
Ø600
Ø10,5 Ø10
6x60°
4x90°
15°
R47,9
R66,6
R50,4
2
117
Ø720
Ø470,3
Ø492,6
Ø630
Ø700
Ø10(4x) Ø9(6x)
15°
4x90°
30°
6x60°
Fan size 710:
Fan size 630:
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
Inlet rings
Dimensioned drawings with one pressure tap
86
2016-02
Effects of installation
space
Effects of installation space:
Installation in a square box may cause a reduction of the air performance.
d = Hydraulic diameter
Formula: d = 2 x B x H / (B + H)
W = Width of the box
H = Height of the box
D = Outside diameter of the fan
D
H
W
0,5
x
D
D
D
h
h
Correction values for the air flow:
1,41,2 1,6 1,8 2,0 2,2
hydraulic diameter dh/D
Correction factor for air flow
1,000,990,980,970,960,950,94
1,7
Fan size:
250 - 560
Fan size:
630 - 900
The correction values shown here were determined from an extensive series of measurements taken on our own internal chamber test rig.
Here, square and rectangular outflow cross sections were considered.
This is why the hydraulic diameter was used to determine the correction values.
The new RadiPac fans are known to be less vulnerable to tight installation situations.
For square cross sections that are greater than 1.7 x the impeller diameter, no deduction has to be applied to the catalog curves.
For RadiPac sizes starting with 630, this is the case from 2.2 x the impeller diameter onward.
87
Air flow
measurement
2016-02
Air flow measurement:
The differential pressure method compares the static pressure upstream of the inlet ring with the static pressure in the inlet ring.
The air flow can be calculated from the differential pressure (between the static pressures) according to the following equation:
q = k V'p q in [m3/h] and 'p in [Pa]
If the air flow is to be regulated to remain constant, the inlet pressure must be kept constant:
'p = q 2 : k2
k takes into account the specific properties of the inlet ring.
The pressure is tapped at 1 (4) point(s) on the circumference of the inlet ring. The customer connection consists of a built-in T-shaped hose fitting.
The hose fitting is suitable for pneumatic hoses with an inside diameter of 4 mm.
VV
V
.
Δp
0,5xD
D
k-factors: (for RadiPac inlet rings)
Fan size
k-factor
Fan size
k-factor
250 280 310 355 400 450 500
76 77 116 148 188 240 281
560 630 710 800 900
348 438 545 695 900
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
88
Spring elements
2016-02
M8
Ø52
*57
– Packaging: Part numbers refer to one set
consisting of 4x spring elements each.
Supplied in a box.
M10
Ø70
*94
Version 1: Version 2:
* Unloaded
Subject to change
Part number (set)
---
Spring elements
Minimum speed
---
Type
--- ---K3G 250 .....
--- ---K3G 250 .....
--- ---K3G 280 .....
--- ---K3G 280 .....
--- ---K3G 280 .....
--- ---K3G 310 .....
--- ---K3G 310 .....
--- ---K3G 310 .....
--- ---K3G 355 .....
Version
---
---
---
---
---
---
---
---
---
---
K3G 250 .....
Deflection
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
--- ---
--- ---K3G 355 .....
--- ---K3G 400 .....
--- ---K3G 400 .....
--- ---K3G 450 .....
--- ---K3G 450 .....
--- ---K3G 450 .....
--- ---K3G 500 .....
--- ---K3G 500 .....
--- ---K3G 560 .....
---
---
---
---
---
---
---
---
---
---
K3G 355 ..... Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
Cube design in preparation
--- ---
11012-4-5142 270 min-1
K3G 630-AR02-01
11013-4-5142 330 min-1
K3G 630-AS05-01
11013-4-5142 310 min-1
K3G 710-AR03-01
11013-4-5142 300 min-1
K3G 710-AS06-01
11013-4-5142 280 min-1
K3G 800-AR08-01
11013-4-5142 280 min-1
K3G 800-AS07-01
11014-4-5142 320 min-1
K3G 900-AR10-01
11014-4-5142 320 min-1
K3G 900-AS08-01
---
2
2
2
2
2
2
2
2
K3G 560 ..... Cube design in preparation
25,7 mm
17,3 mm
19,5 mm
20,3 mm
23,1 mm
23,1 mm
17,8 mm
17,8 mm
Attention: The spring elements offered are matched to the respective fan as a set (4x). Each fan must be installed separately. The installation and operation of several fans on one set of spring elements is not
allowed. The spring elements are designed to achieve the best decoupling efficiency possible. However, when the fan is started up, it will run through the resonance frequency causing a brief vibration to occur.
So when the fan is being operated, care must be taken to ensure that the specified minimum speed is also not undershot when the spring elements indicated are used. This will prevent the fan from being
operated continuously in the resonance frequency. Operation close to or in the resonance frequency will destroy the fan! If spring elements other than those indicated are used, it is mandatory that a check be
made to determine how the resonance frequency, and thus the operating requirements, change.
Vibration-absorbing elements
Part number (set)
---
Minimum speed
---
Type
--- ---K3G 250 .....
--- ---K3G 250 .....
--- ---K3G 280 .....
--- ---K3G 280 .....
--- ---K3G 280 .....
--- ---K3G 310 .....
--- ---K3G 310 .....
--- ---K3G 310 .....
--- ---K3G 355 .....
Deflection
---
---
---
---
---
---
---
---
---
---
K3G 250 ..... -- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
--- ---
--- ---K3G 355 .....
--- ---K3G 400 .....
--- ---K3G 400 .....
--- ---K3G 450 .....
--- ---K3G 450 .....
--- ---K3G 450 .....
--- ---K3G 500 .....
--- ---K3G 500 .....
--- ---K3G 560 .....
---
---
---
---
---
---
---
---
---
---
K3G 355 ..... -- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
-- -- -- -- -- Cube design in preparation
--- ---
10005-4-5164 680 min-1
K3G 630-AR02-01
10006-4-5164 740 min-1
K3G 630-AS05-01
10005-4-5164 620 min-1
K3G 710-AR03-01
10006-4-5164 680 min-1
K3G 710-AS06-01
10005-4-5164 570 min-1
K3G 800-AR08-01
10006-4-5164 640 min-1
K3G 800-AS07-01
10005-4-5164 520 min-1
K3G 900-AR10-01
10006-4-5164 580 min-1
K3G 900-AS08-01
---
2,9 mm
2,4 mm
3,5 mm
2,9 mm
4,1 mm
3,3 mm
5,0 mm
3,9 mm
K3G 560 ..... -- -- -- -- -- Cube design in preparation
40 M10 40 28 10
50 M10 50 28 10
40 M10 40 28 10
50 M10 50 28 10
40 M10 40 28 10
50 M10 50 28 10
40 M10 40 28 10
50 M10 50 28 10
89
Vibration-absorbing
elements
2016-02
T
HL
G
G
D
– Packaging: Part numbers refer to one set
consisting of 4x rubber buffers, washers,
and nuts each.
Supplied in a box.
D G H L T
Subject to change Attention: The vibration-absorbing elements offered are matched to the respective fan as a set (4x). Each fan must be installed separately. The installation and operation of several fans on one set of vibration-
absorbing elements is not allowed. The vibration-absorbing elements are designed to achieve the best decoupling efficiency possible. However, when the fan is started up, it will run through the resonance
frequency causing a brief vibration to occur. So when the fan is being operated, care must be taken to ensure that the specified minimum speed is also not undershot when the vibration-absorbing elements
indicated are used. This will prevent the fan from being operated continuously in the resonance frequency. Operation close to or in the resonance frequency will destroy the fan! If vibration-absorbing elements
other than those indicated are used, it is mandatory that a check be made to determine how the resonance frequency, and thus the operating requirements, change.
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
90
2016-02
91
Connection diagrams
2016-02
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
92
Technical features:
• Control input 0-10 VDC / PWM • Reverse plarity and locked-rotor protection / Soft start
• Output 10 VDC (+10 %) max. 10 mA • Motor current limitation / Alarm relay
• Output 20 VDC (+/-20 %) max. 50 mA • RS 485 MODBUS-RTU / PFC, passive
• Output for slave 0-10 V max. 5 mA • Thermal overload protection for electronics/motor
• Input for sensor 0-10 V or 4-20 mA • Undervoltage/phase failure detection
• Operation and fault indicator • Control interface with SELV potential safely disconnected from supply
• Integrated PI controller • External enable input/External 24 V input (parameterization)
+20 V
Ain2 I
Aout
PE
NO
COM
NC
14
321
Ain2 U
11
GND
10
Din3
9
+10 V
Ain1 I
Din1
7
Ain1 U
4
GND
3
RS B
2
KL 3 KL 2
L1
L2
L3
321
KL 1
56
12 13
Din2
8
RS A
1
Connection diagram: M3)
M3G112 / M3G150 / M3G200
2016-02
Terminal
1
2
4
7
11
12
3
KL1
grün/gelb
KL3
PE
13
2
3/10
1
1
2
3
KL2
6
5
8
9
14
Pin Connection
L1
L2
PE
Assignment/function
Supply connection, power supply 3-phase 380-480 VAC, 50/60 Hz
Supply connection, power supply 3-phase 380-480 VAC, 50/60 Hz
Ground connection, PE connection
Ain1 U /PWM Analog input 1 (set value); 0-10 V; Ri= 100 kΩ; adjustable curve; only for use as alternative to input Ain1 I, SELV
Din1 Digital input 1: Enable electronics; Enable: Pin open or applied voltage 5...50 VDC; Disable: Bridge to GND or applied voltage < 1 VDC;
Reset function: Triggering of software reset after level change to < 1VDC, SELV
Ain2 U Analog input 2; Measured value 0-10 V; Ri= 100 kΩ; adjustable curve; only for use as alternative to input 11 Ain2 I, SELV
+20 V Fixed voltage output 20 VDC; +20 V +25/-10 %; max. 50 mA; short-circuit-proof;
power supply for external devices (e.g. sensor), SELV
L3 Supply connection, power supply 3-phase 380-480 VAC, 50/60 Hz
Ain2I Analog input 2; Measured value 4-20 mA; Ri= 100 Ω; adjustable curve, only for use as alternative to input Ain2 U, SELV
RSB Bus connection RS485; RSB; MODBUS RTU
GND Reference ground for control interface, SELV
RSA Bus connection RS485; RSA; MODBUS RTU
NO
COM
Status relay, floating status contact, make for failure
Status relay, floating status contact, changeover contact, common connection| (2 A, 250 V, min. 10 mA, AC1)
NC Status relay, floating status contact, break for failure
Ain1I Analog input 1 (set value); 4-20 mA; Ri= 100 Ω; adjustable curve, only for use as alternative to input Ain1 U, SELV
+10 V Fixed voltage output 10 VDC; +10 V ±3 %; max. 10 mA; short-circuit-proof;
power supply for external devices (e.g. potentiometer), SELV
Din2 Digital input 2: Switching parameter sets 1/2, according to EEPROM setting, the valid/used parameter set can be selected via bus or
via digital input Din2. Parameter set 1: Pin open or applied voltage 5-50 VDC;
Parameter set 2: Bridge to GND or applied voltage < 1 VDC, SELV
Din3 Digital input 3: Direction of action of integrated controller; According to EEPROM setting, the direction of action of the integrated
controller can be selected as normal/inverse via bus or digital input; Normal: Pin open or applied voltage 5...50 VDC;
Inverse: Bridge or applied voltage < 1 VDC, SELV
Aout Analog output 0-10 V; max. 5 mA; output of current motor modulation level/current motor speed.
Adjustable curve, SELV
93
Technical features:
• Control input 0-10 VDC / PWM • Reverse plarity and locked-rotor protection
• Output 10 VDC max. 10 mA • Motor current limitation
• Operation and fault indicator • RS 485 MODBUS-RTU
• Integrated PI controller • Thermal overload protection for electronics/motor
• Alarm relay • Undervoltage/phase failure detection
• Soft start • Control interface with SELV potential safely disconnected from supply
• PFC, passive • External enable input/External 24 V input (parameterization)
NC
PE
L1
L2
L3
8
321
Ain1 U
7
+10 V
6
Din1
5
COM
4
GND
3
RS B
2
RS A
1
KL 2 KL 1
2016-02
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
Connection diagram: M5)
M3G150
1
2
4
5
6
7
3
KL1
grün/gelb
KL2
PE
8
2
3
1
Pin Connection
L1
L2
PE
Assignment/function
Supply connection, power supply 3-phase 380-480 VAC, 50/60 Hz
Supply connection, power supply 3-phase 380-480 VAC, 50/60 Hz
Ground connection, PE connection
COM Status relay, floating status contact, changeover contact, common connection, contact rating 250 VAC / 2 A (AC1)
Din1 Digital input 1: Enable electronics; Enable: Pin open or applied voltage 5...50 VDC; Disable: Bridge to GND or applied voltage < 1 VDC;
Reset function: Triggering of software reset after level change to < 1VDC, SELV
+10 V Fixed voltage output 10 VDC; +10 V ±3 %; max. 10 mA; short-circuit-proof;
power supply for external devices (e.g. potentiometer), SELV
Ain1 U /PWM Analog input 1 (set value); 0-10 V; Ri= 100 kΩ; adjustable curve, SELV
L3 Supply connection, power supply 3-phase 380-480 VAC, 50/60 Hz
Terminal
NC Status relay, floating status contact; break for failure
RSB Bus connection RS485; RSB; MODBUS RTU, SELV
GND Reference ground for control interface, SELV
RSA Bus connection RS485; RSA; MODBUS RTU, SELV
94
Technical features:
• Control input 0-10 VDC / PWM • Motor current limitation
• Output 10 VDC max. 10 mA • RS 485 MODBUS-RTU
• Operation and fault indicator • Thermal overload protection for electronics/motor
• Alarm relay • Undervoltage/phase failure detection
• Locked-rotor protection, Soft start • Control interface with SELV potential safely disconnected from supply
• Power limiter
• PFC, active
L
NC
COM
0-10 V
RSB
RSA
GND
Wire 1 Wire 2
white 2black white 1 bluewhitebrownyellow
N
blue
PE
green/yellow
+10 V
red
2016-02
Connection diagram: P5)
M3G084, 1~
RSA
11 RSA
Speed
Full
potentiometer
setting with
Speed
<1 V -> n = 0
1 V -> n = min
10 V -> n = max
setting
Speed
1-10 V
10 K
47 K
Imax=10 mA
10
47 K
PE1
A2
A1
14
11
470 nF
L
N
GND
PE
10 V
0-10V/PWM
NC
COM
8
8
88
7
6
5
3
2
PE
1
12
12
12
13
13
13
10 V
0 V
0-10
V
RSB
10 RSB
Customer Connection Fan
green/yel.
black
blue
white 1
white 2
yellow
brown
white
blue
red
1, 2
3
5
schwarz
blau
grün/gelb
1
1
1
6blau
1
7gelb
1
8 rot2
10 weiß2
11 weiß2
12 weiß2
13 weiß
2
PE
N
L
NC
COM
0-10 V / PWM
RSB
RSA
GND
+ 10 V
Wire No. Color Assignment/function
Protective earth
Power supply, neutral conductor, voltage range see nameplate, 50/60 Hz
Power supply, phase, voltage range see nameplate, 50/60 Hz
Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on supply side and reinforced insulation on control interface side
Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on supply side and reinforced insulation on control interface side
Analog input (set value), SELV 0-10 V, impedance 100 kΩ, adjustable curve
RS485 interface for MODBUS, RSB, SELV
RS485 interface for MODBUS, RSA, SELV
Reference ground for control interface, SELV
Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof,
power supply for ext. devices (e.g. potentiometer)
Connection ColorColor
95
Technical features:
• Control input 0-10 VDC / PWM • Motor current limitation
• Output 10 VDC max. 10 mA • RS 485 MODBUS-RTU
• Operation and fault indicator • Thermal overload protection for electronics/motor
• Integrated PI controller • Undervoltage/phase failure detection
• Alarm relay • External 24 V input (parameterization)
• Locked-rotor protection, Soft start • Write cycles EEPROM max. 100,000
• PFC, passive • Control interface with SELV potential safely disconnected from supply
13
weiß
Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof,
power supply for ext. devices (e.g. potentiometer), SELV
Fixed voltage output 24 VDC for setting parameters via MODBUS without line voltage supply
2 + 10 V
weiß
red
L3
NC
COM
0-10 V
RSB
RSA
GND
Wire 1 Wire 2
white 2black white 1 bluewhitebrownyellow
L2
black
L1
black
+10 V
red
PE
green/yellow
2016-02
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
Connection diagram: P6)
M3G084, 3~
RSA
11 RSA
Speed
Full
potentiometer
setting with
Speed
<1 V -> n = 0
1 V -> n = min
10 V -> n = max
setting
Speed
1-10 V
10 K
47 K
Imax=10 mA
10
47 K
PE1
A2
A1
14
11
470 nF
L3
L1
GND
PE
10 V
0-10V/PWM
NC
COM
8
8
88
7
6
5
L2
4
3
2
PE
1
12
12
12
13
13
13
10 V
0 V
0-10
V
RSB
10 RSB
Customer Connection Fan
1, 2
3, 4, 5
1
1
61
71
82
102
112
122
Wire No. Color Assignment/function
Protective earth
Power supply, phase, voltage range see nameplate, 50/60 Hz
Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on supply side and reinforced insulation on control interface side
Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on supply side and reinforced insulation on control interface side
Analog input (set value), SELV 0-10 V, impedance 100 kΩ, adjustable curve
RS485 interface for MODBUS, RSB, SELV
RS485 interface for MODBUS, RSA, SELV
Reference ground for control interface, SELV
Connection
PE
L1, L2, L3
NC
COM
0-10 V / PWM
RSB
RSA
GND
ColorColor
green/yel.
black
white 1
white 2
yellow
brown
white
blue
96
Technical features:
• Control input 0-10 VDC / PWM • Motor current limitation
• Output 10 VDC max. 10 mA • RS 485 MODBUS-RTU
• Operation and fault indicator • Thermal overload protection for electronics/motor
• Integrated PI controller • Undervoltage/phase failure detection
• Alarm relay • External 24 V input (parameterization)
• Locked-rotor protection, Soft start • Write cycles EEPROM max. 100,000
• PFC, passive • Control interface with SELV potential safely disconnected from supply
L2
L3
NC
COM
GND
RSA
RSB
645 10987
L1
3
PE
2
0-10 V
11
+10 V
24 V IN
12
PE
1
2016-02
Connection diagram: P8)
M3G084 & M3G112, 3~
1, 2
3
5
6
7
8
9
10
11
12
4
No. Assignment/function
Protective earth
Power supply, voltage range see nameplate, 50/60 Hz
Power supply, voltage range see nameplate, 50/60 Hz
Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on supply side and reinforced insulation on control interface side
Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1)
min. 10 mA, basic insulation on supply side and reinforced insulation on control interface side
Reference ground for control interface, SELV
RS485 interface for MODBUS, RSA, SELV
RS485 interface for MODBUS, RSB, SELV
Analog input (set value), SELV 0-10 V, impedance 100 kΩ, adjustable curve
Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof,
power supply for ext. devices (e.g. potentiometer), SELV
Fixed voltage output 24 VDC for setting parameters via MODBUS without line voltage supply
Connection
PE
L1
L3
NC
COM
GND
RSA
RSB
0-10 V / PWM
+10 V
Power supply, voltage range see nameplate, 50/60 HzL2
97
2016-02
Technical features:
• Control input 0-10 VDC / PWM • Motor current limitation, Alarm relay
• Input for sensor 0-10 V or 4-20 mA • RS 485 MODBUS-RTU
• Output for slave 0-10 V max. 3 mA • Thermal overload protection for electronics/motor
• Output 20 VDC (+25 %/-10 %) max. 50 mA • Undervoltage/phase failure detection
• Output 10 VDC (+/-3 %) max. 10 mA • Locked-rotor protection, Soft start
• Integrated PI controller • External 24 V input (parameterization)
• PFC, passive • Control interface with SELV potential safely disconnected from supply
PE
NO
COM
NC
0-10 V
PWM
GND
OUT
+10 V
KL 2
L2
L3
Connection
L3
L2
PE
Assignment/function
Power supply, voltage range see nameplate, 50/60 Hz
Power supply, voltage range see nameplate, 50/60 Hz
Protective earth
+10 V Voltage output 10 VDC (±3 %), max. 10 mA,
power supply for ext. devices (e.g. potentiometer), SELV
L1 Power supply, voltage range see nameplate, 50/60 Hz
Farbe
KL1
grün/gelb
KL3
Terminal
PE
GND Reference ground for control interface, SELV
0-10 V / PWM Control input/current sensor value input 0-10 VDC, (impedance 100 kΩ), only for use as alternative to input 4-20 mA, SELV
OUT Analogue output 0-10 VDC max. 3 mA, SELV;
Output of the actual motor duty cycle (PWM): 1 V corresponds to 10 % PWM, 10 V correspond to 100 % PWM.
NC
COM
Status relay, floating status contact; break for failure
Status relay, floating status contact, common connection (2 A, 250 V, min. 10 mA, AC1)
NO Status relay, floating status contact; make for failure
KL2
4-20 mA Control input/current sensor value input 4-20 mA, (Impedanz 100 Ω), only for use as alternative to input 0-10 V, SELV
+20 V Voltage output 20 VDC (+25/-10 %), max. 50 mA,
power supply for ext. devices (e.g. sensor), SELV
0-10 V
PWM
4-20 mA
+ 20 V
GND
RS B
RS A
RS B
RS A
L1
KL 3 KL 1
RSA RS485 interface for MODBUS RTU; RSA, SELV
GND Reference ground for control interface, SELV
RSB RS485 interface for MODBUS RTU; RSB, SELV
0-10 V / PWM Control input/current sensor value input 0-10 VDC, (Impedanz 100 kΩ), only for use as alternative to input 4-20 mA, SELV
RSA RS485 interface for MODBUS RTU; RSA, SELV
RSB RS485 interface for MODBUS RTU; RSB, SELV
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
Connection diagram: L6)
M3G084, 3~ (compact)
98
2016-02
Technical parameters and scope
High standards for all ebm-papst products
At ebm-papst we are always looking to improve our products to be able to offer customers just what they need for their particular requirements. Careful
monitoring of the market enables us to constantly incorporate enhancements into our products. As shown by the technical parameters listed below,
you can always be sure of fi nding the right solution from ebm-papst for whatever application you may have in mind.
General performance parameters
Any deviations from the technical data and technical parameters described
here are given in the product-specifi c data sheet.
Degree of protection
The degree of protection is specifi ed in the product-specifi c data sheets.
Insulation class
The insulation class is specifi ed in the product-specifi c data sheets.
Installation position
The installation position is specifi ed in the product-specifi c data sheets.
Condensation drainage holes
Information on condensation drainage holes is provided in the product-
specifi c data sheets.
Mode of operation
The mode of operation is specifi ed in the product-specifi c data sheets.
Protection class
The protection class is specifi ed in the product-specifi c data sheets.
Service life
The service life of ebm-papst products depends on two main factors:
– The service life of the insulation system
– The service life of the bearing system
The service life of the insulation system is essentially governed by the
voltage level, the temperature and the ambient conditions such as
humidity and condensation.
The service life of the bearing system is primarily governed by the
thermal load on the bearings. For the majority of our products we use
maintenance-free ball bearings which can be fi tted in any installation
position. Sleeve bearings can alternatively be employed, as described in
the product-specifi c data sheets.
As a rough guide (depending on the general conditions), the ball bearings
have a life expectancy L10 of approx. 40,000 hours of operation at an
ambient temperature of 40 °C.
We will gladly provide you with a life expectancy calculation based on your
specifi c usage conditions.
Motor protection/thermal protection
Information on motor protection and thermal protection is provided in the
product-specifi c data sheets.
The following protection methods are provided depending on the type of
motor and area of application:
– Thermal overload protector, in-circuit or external
– PTC with electronic diagnostics
– Impedance protection
– Thermal overload protector with electronic diagnostics
– Current limitation via electronics
If use is made of an external thermal overload protector, a commercially
available tripping unit must be connected by the customer for shut-off.
Motor protection conforming to the applicable standard must be fi tted for
products not provided with a built-in thermal overload protector and not
protected against improper use.
Mechanical strain/performance parameters
All ebm-papst products are subjected to comprehensive testing in confor-
mity with the normative specifi cations and also incorporating the extensive
experience of ebm-papst.
99
2016-02
Vibration testing
Vibration testing is performed as follows:
– Vibration test in operation according to DIN IEC 68 Part 2-6
– Vibration test at standstill according to DIN IEC 68 Part 2-6
Shock load
Shock load testing is performed as follows:
– Shock load according to DIN IEC 68 Part 2-27
Balancing grade
Balancing grade testing is performed as follows:
– Residual imbalance according to DIN ISO 1940
– Standard balancing quality level G 6.3
Should your particular application require a higher level of balancing,
please contact us and specify the details in your order.
Chemical and physical strain/performance parameters
Please consult your ebm-papst contact for any questions regarding
chemical and physical strain.
Areas of use, industries & applications
Our products are used in a variety of industries and for numerous
applications:
Ventilation, air conditioning and refrigeration technology, clean room
technology, automotive and railway engineering, medical and laboratory
technology, electronics, computer and offi ce systems, telecommunications,
household appliances, heating systems, machinery and installations, drive
engineering.
Our products are not intended for use in the aerospace industry!
Legal and normative specifi cations
The products described in this catalog are developed and manufactured in
accordance with the standards applying to the particular product and,
if known, in accordance with the conditions of the particular area of
application.
Standards
Information on standards is provided in the product-specifi c data sheets.
EMC
Information on EMC standards is provided in the product-specifi c data
sheets.
Compliance with EMC standards has to be assessed on the fi nal product,
as EMC properties may change under different installation conditions.
Touch current
Information on touch current is provided in the product-specifi c data
sheets.
Measurement is performed according to IEC 60990.
Approvals
Please contact us if you require a specifi c type of approval (VDE, UL, GOST,
CCC, CSA, etc.) for your ebm-papst product.
Most of our products can be supplied with the applicable approval.
Information on existing approvals is provided in the product-specifi c data
sheets.
Air performance measurements
All air performance measurements are conducted on intake-side chamber
test rigs conforming to the requirements of ISO 5801 and DIN 24163. The
fans under test are attached to the measuring chamber with free air intake
and exhaust (installation category A) and operated at nominal voltage,
with alternating current also at nominal frequency, without any additional
attachments such as a guard grill.
As required by the standards, the air performance curves shown are
referenced to an air density of 1.15 kg/m3.
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
100
2016-02
Air and sound measurement conditions
Measurements on ebm-papst products are taken under the following
conditions:
– Axial and diagonal fans in airfl ow direction “V” in full nozzle without
guard grille
– Backward-curved centrifugal fans, free-running with inlet ring
– Forward-curved single and dual-inlet centrifugal fans with housing
– Backward-curved dual-inlet centrifugal fans with housing
Sound measurements
All sound measurements are taken in anechoic rooms with reverberant
fl oor. ebm-papst acoustic test chambers meet the requirements of
accuracy class 1 as per DIN EN ISO 3745. For sound measurement, the
fans being tested are positioned in a reverberant wall and operated at
nominal voltage, with alternating current also at nominal frequency,
without any additional attachments such as a guard grill.
Sound pressure and sound power level
All acoustic values are determined in accordance with ISO 13347,
DIN 45635 and ISO 3744/3745 as per accuracy class 2 and given
in A-rated form.
For measurement of the sound pressure level Lp the microphone is located
on the intake side of the fan being tested, generally at a distance of 1 m on
the fan axis.
For measurement of the sound power level Lw 10 microphones are distrib-
uted over an enveloping surface on the intake side of the fan being tested
(see graphic). The measured sound power level can be roughly calculated
from the sound pressure level by adding 7 dB.
Measurement set-up according to ISO 13347-3 and DIN 45635-38:
10 measuring points
d ≥ D
h = 1.5d ... 4.5d
Measurement area S = 6d2 + 7d (h + 1.5d)
3d
2d
h
D
1.5d
Technical parameters and scope
101
2016-02
Cumulative level of several sound sources with the same level
The addition of 2 sound sources with the same level produces a level increase of approx. 3 dB.
The noise characteristics of several identical fans can be predicted on the basis of the sound
values specifi ed in the data sheet. This is shown in the adjacent graph.
Example: There are 8 axial fans A3G800 on a condenser. According to the data sheet, the sound
pressure level of one fan is 75 dB(A). The level increase determined from the graph is 9 dB.
This means that a total level of 84 dB(A) is to be expected for the installation.
Cumulative level of two sound sources with different levels
The noise characteristics of two different fans can be predicted on the basis of the sound values
specifi ed in the data sheet. This is shown in the adjacent graph.
Example: In a ventilation unit, there is one axial fan A3G800 with a sound pressure level
of 75 dB(A) at the point of operation and one axial fan A3G710 with 71 dB(A). The difference in
level is 4 dB. The level increase of approx. 1.5 dB can now be read off the graph. This means
that a total level of 76.5 dB(A) is to be expected for the unit.
Distance laws
The sound power level is not governed by the distance from the noise source. By contrast, the
sound pressure level decreases with increasing distance from the sound source. The adjacent
graph shows the decrease in level under far fi eld conditions. Far fi eld conditions apply if there is
a considerable distance between the microphone and the fan in relation to the fan diameter and
the wavelength under consideration. On account of the complexity of the topic, literature should
be consulted for more detailed information on far fi elds. The level in the far fi eld decreases by
6 dB each time the distance is doubled. Different relationships apply in the near fi eld of the fan
and the level may decrease to a far lesser extent. The following example only applies to far fi eld
conditions and may vary considerably as a result of installation effects:
For an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of 1 m.
From the adjacent graph, this would yield a reduction of 26 dB at a distance of 20 m, i.e. a sound
pressure level of 39 dB(A).
15
10 15 20 2
5
582 3
105 90
1
Number of sources of sound with identical level
Increase in sound pressure / sound power level
4 6 7 9
[dB]
[dB(A)]
3
12 16 20 2
4
84
21 1,50
0
Difference in level with two sources of sound
Increase in sound pressure / sound power level [dB]
[dB(A)]
[dB]
[dB(A)]
0
10 20 50 10052
-10-26 -20-30-40
1
[m]
Distance
Decrease in sound pressure level [dB]
[dB(A)]
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
102
ebm-papst Mulfi ngen GmbH & Co. KG
Bachmühle 2
74673 Mulfi ngen
GERMANY
Phone +49 7938 81-0
Fax +49 7938 81-110
info1@de.ebmpapst.com
ebm-papst St. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
78112 St. Georgen
GERMANY
Phone +49 7724 81-0
Fax +49 7724 81-1309
info2@de.ebmpapst.com
ebm-papst Landshut GmbH
Hofmark-Aich-Straße 25
84030 Landshut
GERMANY
Phone +49 871 707-0
Fax +49 871 707-465
info3@de.ebmpapst.com
2016-02
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
16341 Panketal
GERMANY
Phone +49 30 944149-62
Fax +49 30 944149-63
Jens.Duchow@de.ebmpapst.com
Bielefeld
Dipl.-Ing. (FH) Wolf-Jürgen Weber
Niehausweg 13
33739 Bielefeld
GERMANY
Phone +49 5206 91732-31
Fax +49 5206 91732-35
Wolf-Juergen.Weber@de.ebmpapst.com
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
59519 Möhnesee-Völlinghausen
GERMANY
Phone +49 2925 800-407
Fax +49 2925 800-408
Hans-Joachim.Pundt@de.ebmpapst.com
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr.-Hermann-Krause-Straße 23
63452 Hanau
GERMANY
Phone +49 6181 1898-12
Fax +49 6181 1898-13
Christian.Kleffmann@de.ebmpapst.com
Halle
Dipl.-Ing. (TU) Michael Hanning
Lercheneck 4
06198 Salzatal / OT Lieskau
GERMANY
Phone +49 345 55124-56
Fax +49 345 55124-57
Michael.Hanning@de.ebmpapst.com
Hamburg
Ingenieurbüro Breuell GmbH
Ing. Dirk Kahl
Elektroingenieur
Oststraße 96
22844 Norderstedt
GERMANY
Phone +49 40 538092-19
Fax +49 40 538092-84
Kahl@breuell-hilgenfeldt.de
Heilbronn / Heidelberg
Dipl.-Ing. Mark Gartner
Gehrweg 12
74199 Unterheinriet
GERMANY
Phone +49 7130 404569-1
Fax +49 7130 404569-2
Mark.Gartner@de.ebmpapst.com
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
35075 Gladenbach
GERMANY
Phone +49 6462 4071-10
Fax +49 6462 4071-11
Ralph.Brueck@de.ebmpapst.com
Koblenz
Winfried Schaefer
Hinter der Kirch 10
56767 Uersfeld
GERMANY
Phone +49 2657 16-96
Fax +49 2657 16-76
Winfried.Schaefer@de.ebmpapst.com
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Landsbergerstraße 14
86932 Pürgen
GERMANY
Phone +49 8196 99877-54
Fax +49 8196 99877-55
Jens.Peter@de.ebmpapst.com
Nuremberg
Dipl.-Wirt.-Ing. (FH) Axel Resch
Dr.-August-Koch-Str. 1
91639 Wolframs-Eschenbach
GERMANY
Phone +49 9875 9783-170
Fax +49 9875 9783-171
Axel.Resch@de.ebmpapst.com
Offenburg
Dipl.-Ing. (FH) Ralf Braun
Hubeneck 21
77704 Oberkirch
GERMANY
Phone +49 7802 9822-52
Fax +49 7802 9822-53
Ralf.Braun@de.ebmpapst.com
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
73207 Plochingen
GERMANY
Phone +49 7153 9289-80
Fax +49 7153 9289-81
Rudi.Weinmann@de.ebmpapst.com
Ulm
M.Sc. Reinhard Sommerreißer
Am Germanenring 13
86674 Baar / Schwaben
GERMANY
Phone +49 8276 5899-775
Fax +49 8276 5899-776
Reinhard.Sommerreisser@de.ebmpapst.com
Distributors
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
63110 Rodgau - Jügesheim
GERMANY
Phone +49 6106 841-0
Fax +49 6106 841-111
info@red-elektromechanik.de
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Oststraße 96
22844 Norderstedt
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
info@breuell-hilgenfeldt.de
Munich
A. Schweiger GmbH
Ohmstraße 1
82054 Sauerlach
GERMANY
Phone +49 8104 897-0
Fax +49 8104 897-90
info@schweiger-gmbh.de
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Oststraße 96
22844 Norderstedt
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
info@breuell-hilgenfeldt.de
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
74677 Dörzbach
GERMANY
Phone +49 7937 80355-20
Fax +49 7937 80355-25
info@hds-gmbh.net
www.hds-gmbh.net
ebm-papst in Germany
fan agent compact fan agent motor specialist motor agent
103
2016-02
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Straubingstraße 17
4030 Linz
AUSTRIA
Phone +43 732 321150-0
Fax +43 732 321150-20
info@at.ebmpapst.com
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
Lipkovskaya Gasse 34
Offi ce No.6, Room 106,107
223010 Minsk
BELARUS
Phone +375 17 3851556
Fax +375 17 3851556
info@by.ebmpapst.com
www.ebmpapst.by
Belgium
ebm-papst Benelux B.V.
Sales offi ce Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
3001 Heverlee-Leuven
BELGIUM
Phone +32 16 396-200
Fax +32 16 396-220
info@be.ebmpapst.com
www.ebmpapst.be
Bulgaria
ebm-papst Romania S.R.L.
Str. Tarnavei No. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
dudasludovic@xnet.ro
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
offi ce@hu.ebmpapst.com
Cyprus
Helcoma
E. Rota and Co. OE
Davaki 65
17672 Kallithea-Attiki
GREECE
Phone +30 210 9513-705
Fax +30 210 9513-490
contact@helcoma.gr
www.helcoma.gr
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Kaštanová 34a
620 00 Brno
CZECH REPUBLIC
Phone +420 544 502-411
Fax +420 547 232-622
info@ebmpapst.cz
www.ebmpapst.cz
Denmark
ebm-papst Denmark ApS
Vallensbækvej 21
2605 Brøndby
DENMARK
Phone +45 43 631111
Fax +45 43 630505
mail@dk.ebmpapst.com
www.ebmpapst.dk
Estonia
ebm-papst Oy, Eesti Filiaal
Kesk tee 13
Aaviku küla, Jüri Tehnopark
75301 Rae Vald, Harjumaa
ESTONIA
Phone +372 65569-78
Fax +372 65569-79
www.ebmpapst.ee
Finland
ebm-papst Oy
Puistotie 1
02760 Espoo
FINLAND
Phone +358 9 887022-0
Fax +358 9 887022-13
mailbox@ebmpapst.fi
www.ebmpapst.fi
France
ebm-papst sarl
Parc d’Activités Nord
1 rue Mohler – BP 62
67212 Obernai Cedex
FRANCE
Phone +33 3 88 66 88 03
info@ebmpapst.fr
www.ebmpapst.fr
Greece
Helcoma
E. Rota and Co. OE
Davaki 65
17672 Kallithea-Attiki
GREECE
Phone +30 210 9513-705
Fax +30 210 9513-490
contact@helcoma.gr
www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
offi ce@hu.ebmpapst.com
Iceland
RJ Engineers
Stangarhyl 1a
110 Reykjavik
ICELAND
Phone +354 567 8030
Fax +354 567 8015
rj@rj.is
www.rj.is
Ireland
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
sales@uk.ebmpapst.com
www.ebmpapst.co.uk
AuBren Limited
Portlaoise Business & Technology Park
Mountrath Road
Portlaoise, Co. Laois
IRELAND
Phone +353 57 8664343
Fax +353 57 8664346
sales@ie.aubren.com
www.aubren.com
Italy
ebm-papst Srl
Via Cornaggia 108
22076 Mozzate (Co)
ITALY
Phone +39 0331 836201
Fax +39 0331 821510
info@it.ebmpapst.com
www.ebmpapst.it
ebm-papst in Europe
fan agent compact fan agent motor specialist motor agent
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
104
2016-02
ebm-papst in Europe
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
offi ce@hu.ebmpapst.com
Netherlands
ebm-papst Benelux B.V.
Polbeemd 7 - 5741 TP Beek en Donk
P.O. Box 140 - 5740 AC Beek en Donk
NETHERLANDS
Phone +31 492 502-900
Fax +31 492 502-950
verkoop@nl.ebmpapst.com
www.ebmpapst.nl
ebm-papst Heating Systems B.V.
Van Veldekekade 360
5216 KT ‘s-Hertogenbosch
NETHERLANDS
Phone +31 73 648 89 00
Fax +31 73 648 89 11
info@ebmpapst-hs.nl
www.ebmpapst-hs.nl
Norway
ebm-papst AS
P.B. 173 Holmlia
1203 Oslo
NORWAY
Phone +47 22 763340
Fax +47 22 619173
mailbox@ebmpapst.no
www.ebmpapst.no
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
03236 Warszawa
POLAND
Phone +48 22 6757819
Fax +48 22 6769587
offi ce@ebmpapst.pl
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Centro Empresarial de Alverca
Rua de Adarse, Vale D’Ervas
Corpo D / Fracção 3
2615-178 Alverca do Ribatejo
PORTUGAL
Phone +351 218 394 880
Fax +351 218 394 759
info@pt.ebmpapst.com
www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tarnavei Nr. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
dudasludovic@xnet.ro
Russia
ebm-papst Rus GmbH
Olimpiyskiy prospect 29A, offi ce 418
141006 Mytistschi, Oblast Moskau
RUSSIA
Phone +7 495 9807524
Fax +7 495 5140924
info@ebmpapst.ru
www.ebmpapst.ru
ebm-papst Ural GmbH
Posadskaja-Strasse, 23(E), 3
620102 Ekaterinburg
RUSSIA
Phone +7 343 2338000
Fax +7 343 2337788
Konstantin.Molokov@ru.ebmpapst.com
www.ebmpapst.ur.ru
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
offi ce@hu.ebmpapst.com
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
28830 San Fernando de Henares (Madrid)
SPAIN
Phone +34 91 6780894
Fax +34 91 6781530
ventas@ebmpapst.es
www.ebmpapst.es
Sweden
ebm-papst AB
Äggelundavägen 2
17562 Järfälla
SWEDEN
Phone +46 10 4544400
Fax +46 8 362306
info@ebmpapst.se
www.ebmpapst.se
Switzerland
ebm-papst AG
Rütisbergstrasse 1
8156 Oberhasli
SWITZERLAND
Phone +41 44 73220-70
Fax +41 44 73220-77
verkauf@ebmpapst.ch
www.ebmpapst.ch
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
35620 Cigli-Izmir
TURKEY
Phone +90 232 3282090
Fax +90 232 3280270
akantel@akantel.com.tr
www.ebmpapst.com.tr
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 21
03067 Kiev
UKRAINE
Phone +38 044 2063091
Fax +38 044 2063091
mail@ebmpapst.ua
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
sales@uk.ebmpapst.com
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane
East Ilsley, Berkshire RG20 7LG
UNITED KINGDOM
Phone +44 1635 2811-11
Fax +44 1635 2811-61
A&Dsales@uk.ebmpapst.com
www.ebmpapst-ad.com
fan agent compact fan agent motor specialist motor agent
105
2016-02
ebm-papst in America and Africa
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
ARGENTINA
Phone +54 11 46576135
Fax +54 11 46572092
ventas@ar.ebmpapst.com
www.ebmpapst.com.ar
Brazil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
06707-100 Cotia - São Paulo
BRAZIL
Phone +55 11 4613-8700
Fax +55 11 4777-1456
vendas@br.ebmpapst.com
www.ebmpapst.com.br
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
Pickering, Ontario, L1W3J9
CANADA
Phone +1 905 420-3533
Fax +1 905 420-3772
sales@ca.ebmpapst.com
www.ebmpapst.ca
Mexico
ebm Industrial S. de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
Mexico 05120, D.F.
MEXICO
Phone +52 55 3300-5144
Fax +52 55 3300-5243
sales@mx.ebmpapst.com
www.ebmpapst.com.mx
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
Farmington, CT 06034
UNITED STATES
Phone +1 860 674-1515
Fax +1 860 674-8536
sales@us.ebmpapst.com
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfi eld, Suite 130
Dearborn, MI 48120
UNITED STATES
Phone +1 313 406-8080
Fax +1 313 406-8081
automotive@us.ebmpapst.com
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
2040 Honeydew
SOUTH AFRICA
Phone +27 11 794-3434
Fax +27 11 794-5020
info@za.ebmpapst.com
www.ebmpapst.co.za
fan agent compact fan agent motor specialist motor agent
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
106
2016-02
ebm-papst in Asia
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
200131 Shanghai
P.R. of CHINA
Phone +86 21 5046-0183
Fax +86 21 5046-1119
sales@cn.ebmpapst.com
www.ebmpapst.com.cn
Hong Kong
ebm-papst Hong Kong Ltd.
Room 17E, MG Tower
133 Hoi Bun Road, Kwun Tong
Hong Kong
P.R. of CHINA
Phone +852 2145-8678
Fax +852 2145-7678
info@hk.ebmpapst.com
India
ebm-papst India Pvt. Ltd.
26/3, G.N.T. Road, Erukkencherry
Chennai-600118
INDIA
Phone +91 44 25372556
Fax +91 44 25371149
sales@in.ebmpapst.com
www.ebmpapst.in
Indonesia
ebm-papst Indonesia
Representative Offi ce
German Centre, 4th Floor, Suite 4470
Jl. Kapt. Subijono Dj. Bumi Serpong Damai
15321 Tangerang
INDONESIA
Phone +62 21 5376250
Fax +62 21 5388305
salesdept@id.ebmpapst.com
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
Kiryat Arie, Petach-Tikva 49514
ISRAEL
Phone +972 3 9100300
Fax +972 3 5796679
polak@polak.co.il
www.polak.co.il
Japan
ebm-papst Japan K.K.
Attend on Tower 13F
Shinyokohama 2-8-12, Kohoku-ku
222-0033 Yokohama-City, Kanagawa
JAPAN
Phone +81 45 47057-51
Fax +81 45 47057-52
info@jp.ebmpapst.com
www.ebmpapst.jp
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
12, WorldCupbuk-ro 56-gil
Mapo-Gu
Seoul 03924
KOREA
Phone +82 2 366213-24
Fax +82 2 366213-26
info@kr.ebmpapst.com
www.ebmpapst.co.kr
Malaysia
ebm-papst Malaysia
Representative Offi ce
Unit 12-2, Jalan USJ Sentral 3
Persiaran Subang, Selangor Darul Ehsan
47600 Subang Jaya
MALAYSIA
Phone +60 3 8024-1680
Fax +60 3 8024-8718
salesdept@my.ebmpapst.com
Philippines
ebm-papst SEA Pte. Ltd.
Representative Offi ce (Philippines)
ALPAP II Building
Trade Street Corner Investment Drive
Unit 1101 Madrigal Business Park
1799 Ayala Alabang / Muntinlupa City
Telefon: +63 02 8042747
Telefax: +63 02 8042757
salesdept@ph.ebmpapst.com
Singapore
ebm-papst SEA Pte. Ltd.
No. 23 Ubi Road 4
#06-00 Olympia Industrial Building
Singapore 408620
SINGAPORE
Phone +65 65513789
Fax +65 68428439
salesdept@sg.ebmpapst.com
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
Tsow-Inn District, Kaohsiung
TAIWAN
Phone +886 7 557-4268
Fax +886 7 557-2788
eteco@ms22.hinet.net
www.ebmpapst.com.tw
Thailand
ebm-papst Thailand Co., Ltd.
99/9 Moo 2, Central Chaengwattana Tower
14th Floor, Room 1402
Chaengwattana Road Bangtarad, Pakkret
11120 Nonthaburi
THAILAND
Phone +66 2 8353785-7
Fax +66 2 8353788
salesdept@th.ebmpapst.com
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
Dubai
UNITED ARAB EMIRATES
Phone +971 4 88608-26
Fax +971 4 88608-27
info@ae.ebmpapst.com
www.ebmpapst.ae
Vietnam
ebm-papst SEA Pte. Ltd.
Representative Offi ce
Room 402, 4th Floor, Sai Gon 3 Building
140 Nguyen Van Thu, District 1
Ho Chi Minh City
VIETNAM
Phone +84 8 39104099 / 39103969
Fax +84 8 39103970
linh.nguyen@vn.ebmpapst.com
fan agent compact fan agent motor specialist motor agent
107
2016-02
ebm-papst in Oceania
Oceania
Australia
ebm-papst A&NZ Pty Ltd.
10 Oxford Road
Laverton North, Victoria, 3026
AUSTRALIA
Phone +61 3 9360-6400
Fax +61 3 9360-6464
sales@ebmpapst.com.au
www.ebmpapst.com.au
New Zealand
ebm-papst A&NZ Pty Ltd.
61 Hugo Johnston Drive, Unit H
Penrose 1061, Auckland
NEW ZEALAND
PO Box 112278,
Penrose 1642, Auckland
Phone +64 9 525-0245
Fax +64 9 525-0246
sales@ebmpapst.com.au
www.ebmpapst.com.au
fan agent compact fan agent motor specialist motor agent
Information
ø 250ø 280ø 310ø 355ø 400ø 450ø 500ø 560ø 630ø 710ø 800ø 900
Compact designTechnologyAgents
www.ebmpapst.com
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
Germany
Phone +49 7938 81-0
Fax +49 7938 81-110
info1@de.ebmpapst.com
37973-7-8811 · 2016-02 · KH-3’
Printed in Germany
