QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1532 12/14 BIT, 25 TO 125 MSPS DUAL ADC LTC2268-14, LTC2268-12, LTC2267-14, LTC2267-12, LTC2266-14, LTC2266-12, LTC2265-14, LTC2265-12, LTC2264-14, LTC2264-12, LTC2263-14, LTC2263-12 DESCRIPTION Demonstration circuit 1532 supports a family of 14/12 BIT 125 MSPS ADCs. Each assembly features one of the following devices: LTC2268-14, LTC2268-12, LTC2267-14, LTC2267-12, LTC2266-14, LTC2266-12, LTC2265-14, LTC2265-12, LTC2264-14, LTC2264-12, LTC2263-14, LTC2263-12 high speed, dual ADCs. The versions of the 1532A demo board are listed in Table 1. Depending on the required resolution and sample rate, the DC1532 is supplied with the appropri- Table 1. ate ADC. The circuitry on the analog inputs is optimized for analog input frequencies from 5 MHz to 140MHz. Refer to the datasheet for proper input networks for different input frequencies. Design files for this circuit board are available. Call the LTC factory. LTC is a trademark of Linear Technology Corporation DC1532 Variants DC1532 VARIANTS ADC PART NUMBER RESOLUTION* MAXIMUM SAMPLE RATE INPUT FREQUENCY 1532A-A LTC2268-14 14-BIT 125 Msps 5MHz-140MHz 1532A-B LTC2267-14 14-BIT 105 Msps 5MHz-140MHz 1532A-C LTC2266-14 14-BIT 80 Msps 5MHz-140MHz 1532A-D LTC2265-14 14-BIT 65 Msps 5MHz-140MHz 1532A-E LTC2264-14 14-BIT 40 Msps 5MHz-140MHz 1532A-F LTC2263-14 14-BIT 25 Msps 5MHz-140MHz 1532A-G LTC2268-12 12-BIT 125 Msps 5MHz-140MHz 1532A-H LTC2267-12 12-BIT 105 Msps 5MHz-140MHz 1532A-I LTC2266-12 12-BIT 80 Msps 5MHz-140MHz 1532A-J LTC2265-12 12-BIT 65 Msps 5MHz-140MHz 1532A-K LTC2264-12 12-BIT 40 Msps 5MHz-140MHz 1532A-L LTC2263-12 12-BIT 25 Msps 5MHz-140MHz 1 QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 1532 12/14 BIT, 25 TO 125 MSPS DUAL ADC Table 2. Performance Summary (TA = 25C) PARAMETER CONDITION VALUE Supply Voltage - DC1532A Depending on sampling rate and the A/D converter provided, this supply must provide up to 500mA. Optimized for 3V Analog input range Depending on SENSE Pin Voltage 1 VPP to 2VPP Minimum Logic High 1.3V Maximum Logic Low 0.6V Nominal Logic levels (100 load, 3.5mA Mode) 350mV/1.25V common mode Minimum Logic levels (100 load, 3.5mA Mode) 247mV/1.25V common mode Logic Input Voltages Logic Output Voltages (differential) [3V 6.0V min/max] Sampling Frequency (Convert Clock Frequency) See Table 1 Encode Clock Level Single ended Encode Mode (ENC- tied to GND) 0-3.6V Encode Clock Level Differential Encode Mode (ENC- not tied to GND) 0.2V-3.6V Resolution See Table 1 Input frequency range See Table 1 SFDR See Applicable Data Sheet SNR See Applicable Data Sheet QUICK START PROCEDURE Demonstration circuit 1532 is easy to set up to evaluate the performance of the LTC2268 A/D converters. Refer to Figure 1 for proper meas- urement equipment setup and follow the procedure below: SETUP If a DC1371 "PStache" Data Acquisition and Col- Start Guide to install the required software and lection System was supplied with the DC1532 for connecting the DC1371 to the DC1532 and to demonstration circuit, follow the DC1371 Quick a PC running Windows 2000 or XP. 2 To provided power supply 3.5-6V + Analog Inputs Channel 1 To provided USB cable Channel 2 Parallel/Serial Single Ended Encode Clock (Use provided DC1075, divide by 4 clock board) Figure 1. DC1532 Setup (zoom for detail) 3 DC1532 DEMONSTRATION CIRCUIT BOARD JUMPERS The DC1532 demonstration circuit board should have the following jumper settings as default positions: (as per Figure 1) J14: LANE: Selects either 1 lane or 2 lane output modes (Default - Removed) NOTE: The DC1371 does not support 1 lane operation. J13: PAR/SER : Selects Parallel or Serial programming mode. (Default - Serial) J15: SHDN: Enables and disables the LTC2268. (Default - Removed) Optional Jumpers: J8: Term: Enables/ Disable optional output termination. (Default - Removed) J2: WP: Enable/Disables write protect for the EEPROM. (Default - Removed) J5: ILVDS: Selects either 1.75mA or 3.5mA of output current for the LVDS drivers. (Default - Removed) APPLYING POWER AND SIGNALS TO THE DC1532 DEMONSTRATION CIRCUIT The DC1371 is used to acquire data from the DC1532, the DC1371 must FIRST be connected to a powered USB port and have 5V applied power BEFORE applying +3.6V to +6.0V across the pins marked "V+" and "GND" on the DC1532. DC1532 requires 3.6V for proper operation. Note: optional jumper should be left open to ensure proper serial configuration. Regulators on the board produce the voltages required for the ADC. The DC1532 demonstration circuit requires up to 500mA depending on the sampling rate and the A/D converter supplied. The DC1532 should not be removed, or connected to the DC1371 while power is applied. ANALOG INPUT NETWORK For optimal distortion and noise performance the RC network on the analog inputs may need to be optimized for different analog input frequencies. For input frequencies above 140 MHz, refer to the LTC2268 datasheet for a proper input network. Other input networks may be more appropriate for input frequencies less that 5MHz. In almost all cases, filters will be required on both analog input and encode clock to provide data sheet SNR. The filters should be located close to the inputs to avoid reflections from impedance dis- continuities at the driven end of a long transmission line. Most filters do not present 50 outside the passband. In some cases, 3dB to 10dB pads may be required to obtain low distortion. If your generator cannot deliver full scale signals without distortion, you may benefit from a medium power amplifier based on a Gallium Arsenide Gain block prior to the final filter. This is particularly true at higher frequencies where IC based operational amplifiers may be unable to deliver the combination of low noise figure and High IP3 point required. A high order filter can be used prior to this final ampli- 4 fier, and a relatively lower Q filter used between the amplifier and the demo circuit. Apply the analog input signal of interest to the SMA connectors on the DC1532 demonstration circuit board marked "J3 AIN1", "J4 AIN2", "J6 AIN3", "J7 AIN4". These inputs correspond with channels 1-4 of the ADC respectively. These inputs are capacitive coupled to Balun transformers ETC1-1-13. ENCODE CLOCK NOTE: Apply an encode clock to the SMA connector on the DC1532 demonstration circuit board marked "J11 CLK+". As a default the DC1532 is populated to have a single ended input. For the best noise performance, the ENCODE INPUT must be driven with a very low jitter, square wave source. The amplitude should be large, up to 3VP-P or 13dBm. When using a sinusoidal signal generator a squaring circuit can be used. Linear Technology also provides demo board DC1075A that divides a high frequency sine wave by four, producing a low jitter square wave for best results with the LTC2268. Using band pass filters on the clock and the analog input will improve the noise performance by reducing the wideband noise power of the signals. In the case of the DC1532 a band pass filter used for the clock should be used prior to the DC1075A. Datasheet FFT plots are taken with 10 pole LC filters made by TTE (Los Angeles, CA) to suppress signal generator harmonics, non-harmonically related spurs and broadband noise. Low phase noise Agilent 8644B generators are used for both the Clock input and the Analog input. connector follows the VITA-57/FMC standard, but all signals should be verified when using an FMC carrier card other than the DC1371. SOFTWARE The DC1371A is controlled by the PScope System Software provided or downloaded from the Linear Technology website at http://www.linear.com/software/. To start the data collection software if "PScope.exe", is installed (by default) in \Program Files\LTC\PScope\, double click the PScope Icon or bring up the run window under the start menu and browse to the PScope directory and select PScope. If the DC1532 demonstration circuit is properly connected to the DC1371, PSCOPE should automatically detect the DC1532, and configure itself accordingly. If everything is hooked up properly, powered and a suitable convert clock is present, clicking the "Collect" button should result in time and frequency plots displayed in the PScope window. Additional information and help for PScope is available in the DC1371A Quick Start Guide and in the online help available within the PScope program itself. DIGITAL OUTPUTS Data outputs. data clock, and frame clock signals are available on J1 of the DC1532. This 5 SERIAL PROGRAMMING PScope has the ability to program the DC1532 board serially through the DC1371. There are several options available in the LTC2268 family that are only available through serially programming. PScope allows all of these features to be tested. These options are available by first clicking on the "Set Demo Bd Options" icon on the PScope toolbar (Figure 3). Figure 3: PScope Toolbar Randomizer - Enables Data Output Randomizer - Off (Default) - Disables data output randomizer - On - Enables data output randomizer Two's complement - Enables two's complement mode - Off (Default) - Selects offset binary mode - On - Selects two's complement mode Sleep Mode- Selects between normal operation, sleep mode: - Off (Default) - Entire ADC is powered, and active This will bring up the menu shown in figure 4. - On - The entire ADC is powered down. Channel 1 Nap- Selects between normal operation and putting channel 1 in nap mode. -Off (Default) - Channel one is active - On - Channel one is in nap mode Channel 2 Nap- Selects between normal operation and putting channel 2 in nap mode. -Off (Default) - Channel two is active - On - Channel two is in nap mode Output Current - Selects the LVDS output drive current - 1.75mA (Default) - LVDS output driver current - 2.1mA - LVDS output driver current - 2.5mA - LVDS output driver current - 3.0mA - LVDS output driver current - 3.5mA - LVDS output driver current - 4.0mA - LVDS output driver current Figure 4: Demobd Configuration Options. - 4.5mA - LVDS output driver current This menu allows any of the options available for the LTC2268 family to be programmed serially. The LTC2268 family has the following options: Internal Termination - Enables LVDS internal termination - Off (Default) - Disables internal termination 6 - On - Enables internal termination Outputs - Enables Digital Outputs - Enabled (Default) - Enables digital outputs - Disabled - Disables digital outputs Test Pattern - Selects Digital output test patterns. The desired test pattern can be entered into the text boxes provided. -Off(default) - ADC input data is displayed -On - Test pattern is displayed. Once the desired settings are selected hit OK and PScope will automatically update the register of the device on the DC1532 demo board. 7 8 9