CL-80A - AMPHENOL - Datasheet.Directory

Technology

SiI 164

PanelLink Transmitter

Data Sheet

Document # SiI-DS-0021-E.doc

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E ii

Silicon Image, Inc.

SiI-DS-0021-E

June 2005

Application Information

To obtain the most updated Application Notes and other useful information for your design, please visit the Silicon

Image web site at www.siliconimage.com or contact your local Silicon Image sales office.

This manual is copyrighted by Silicon Image, Inc. Do not reproduce, transform to any other format, or

send/transmit any part of this documentation without the expressed written permission of Silicon Image, Inc.

T rademark Acknowledgment

Silicon Image, the Silicon Image logo, PanelLink® and the PanelLink® Digital logo are registered trademarks of

Silicon Image, Inc. TMDSTM is a trademark of Silicon Image, Inc. VESA®, FPDTM are trademarks of the Video

Electronics Standards Association. I2C is a trademark of Philips Semiconductor. All other trademarks are the

property of their respective holders.

Disclaimer

This document provides technical information for the user. Silicon Image, Inc. reserves the right to modify the

information in this document as necessary. The customer should make sure that they have the most recent data

sheet version. Silicon Image, Inc. holds no responsibility for any errors that may appear in this document.

Customers should take appropriate action to ensure their use of the products does not infringe upon any patents.

Silicon Image, Inc. respects valid patent rights of third parties and does not infringe upon or assist others to

infringe upon such rights.

All information cont ained herein is subject to change without notice.

Revision History

Revision Date Comment

SiI-DS-0021-A 01/99 Full Release

SiI-DS-0021-B 03/99 Internal Revision B release

SiI-DS-0021-C 04/02 New format. I2C programming and strapping mode

description,TFT mapping and Design Recommendations,

pin names ISEL/RST changed to ISEL/RST# and PD to

PD#.

SiI-DS-0021-D 09/02 Included Pb-free package. Added De-skew range.

Corrected PD# pin number.

SiI-DS-0021-E 06/05 Corrected D1 dimension. Corrected JEDEC code.

Included VCC details for power measurement. Added

code.

SiI 164 PanelLink Transmitter

Data Sheet

iii SiI-DS-0021-E

TABLE OF CONTENTS

General Description........................................................................................................................................ 1

Features ...................................................................................................................................................... 1

SiI 164 Pin Diagram ....................................................................................................................................... 1

Functional Description .................................................................................................................................... 2

PanelLink TMDS Digital Core ..................................................................................................................... 2

I2C Interface and Registers......................................................................................................................... 2

Data Capture Logic ..................................................................................................................................... 3

Electrical Specifications .................................................................................................................................. 4

Absolute Maximum Conditions ................................................................................................................... 4

Normal Operating Conditions ..................................................................................................................... 4

Digital I/O Specifications ............................................................................................................................. 4

DC Specifications........................................................................................................................................ 5

AC Specifications ........................................................................................................................................ 6

Input Timing Diagrams ................................................................................................................................ 7

Pin Descriptions.............................................................................................................................................. 9

Input Pins .................................................................................................................................................... 9

Configuration Pins..................................................................................................................................... 10

Input Voltage Reference Pin ..................................................................................................................... 11

Power Management Pins.......................................................................................................................... 11

Differential Signal Data Pins ..................................................................................................................... 11

Reserved Pins........................................................................................................................................... 11

Power and Ground Pins............................................................................................................................ 11

I2C Registers................................................................................................................................................. 12

I2C Register Mapping................................................................................................................................ 12

I2C Register Definitions............................................................................................................................. 13

I2C Slave Interface and Address ............................................................................................................... 15

Data De-skew Feature .............................................................................................................................. 16

Data Latching Modes ................................................................................................................................ 17

I2C Programming Sequence ..................................................................................................................... 18

Enabling Hot Plug Detection Mode........................................................................................................... 18

Non-I2C/Strap Mode Configuration ........................................................................................................... 19

TFT Panel Data Mapping.............................................................................................................................. 21

Design Recommendations ........................................................................................................................... 24

1.5V to 3.3V I2C Bus Level-Shifting .......................................................................................................... 24

Voltage Ripple Regulation......................................................................................................................... 25

Decoupling Capacitors.............................................................................................................................. 26

Series Damping Resistors on Outputs...................................................................................................... 27

Differential Trace Routing ......................................................................................................................... 27

Package Dimensions and Marking Specification ......................................................................................... 29

Ordering Information..................................................................................................................................... 29

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E iv

LIST OF TABLES

Table 1. Data De-Skew Estimated Values.................................................................................................... 16

Table 2. Sample Programming Sequence for SiI 164 in 12-bit Mode .......................................................... 18

Table 3. Non-I2C/Strap Mode Options .......................................................................................................... 20

Table 4. One Pixel/Clock Input/Output TFT Mode - VESA P&D and FPDI-2 Compliant.............................. 21

Table 5. 24-bit One Pixel/Clock Input with 24-bit Two Pixels/Clock Output TFT Mode................................ 22

Table 6. 18-bit One Pixel/Clock Input with 18-bit Two Pixels/Clock Output TFT Mode................................ 23

Table 7. Recommended Components for Bypass and Decoupling Circuits................................................. 26

LIST OF FIGURES

Figure 1. Pin Diagram for SiI 164 ................................................................................................................... 1

Figure 2. Functional Block Diagram ............................................................................................................... 2

Figure 3. Clock Cycle High/Low Times........................................................................................................... 7

Figure 4. Low Swing Differential Times .......................................................................................................... 7

Figure 5. ISEL/RST# Minimum Timing ........................................................................................................... 7

Figure 6. Input Data Setup/Hold Time to IDCK .............................................................................................. 8

Figure 7. VSYNC, HSYNC and CTL[3:1] Delay Time from DE ...................................................................... 8

Figure 8. DE High and Low Times.................................................................................................................. 8

Figure 9. I2C Data Valid Delay (driving Read Cycle data) .............................................................................. 8

Figure 10. I2C Byte Read.............................................................................................................................. 15

Figure 11. I2C Byte Write .............................................................................................................................. 15

Figure 12. SiI 164 Data De-skew Feature Timing ........................................................................................ 16

Figure 13. 12-bit Input Data Latching ........................................................................................................... 17

Figure 14. 24-bit Input Data Latching ........................................................................................................... 17

Figure 15. Non- I2C/Strap Mode Schematic Example .................................................................................. 19

Figure 16. I2C Bus Voltage Level-Shifting using Fairchild NDC7002N ........................................................ 24

Figure 17. I2C Bus Voltage Level Shifting using Philips GTL 2010 .............................................................. 24

Figure 18. Voltage Regulation using TL431 ................................................................................................. 25

Figure 19. Voltage Regulation using LM317 ................................................................................................ 25

Figure 20. Decoupling and Bypass Capacitor Placement............................................................................26

Figure 21. Decoupling and Bypass Schematic............................................................................................. 26

Figure 22. Series Input Damping Resistors for Driving Source ................................................................... 27

Figure 23. Example of Incorrect Differential Signal Routing ........................................................................ 27

Figure 24. Example of Correct Differential Signal Routing........................................................................... 28

Figure 25. Differential Trace Routing to DVI Connector(Top Side View) ..................................................... 28

Figure 26. 64-pin TQFP Package Dimensions (JEDEC code MS-026ACD) ............................................... 29

SiI 164 PanelLink Transmitter September 2002

Data Sheet

1 SiI-DS-0021-E

General Description

The SiI 164 transmitter uses PanelLink® Digital

technology to support displays ranging from VGA to

UXGA resolutions (25 - 165Mpps) in a single link

interface.

The SiI 164 transmitter has a highly flexible interface

with either a 12-bit mode (½ pixel per clock edge) or

24-bit mode 1 pixel per clock edge input for true color

(16.7 million) support. In 24-bit mode, the SiI 164

supports single or dual edge clocking. In 12-bit mode,

the SiI164 supports dual edge single clocking or

single edge dual clocking. The SiI 164 can be

programmed though an I2C interface. In addition the

SiI 164 also supports Receiver and Hot Plug

Detection.

PanelLink Digital technology simplifies PC design by

resolving many of the system level issues associated

with high-speed mixed signal design, providing the

system designer with a digital interface solution that

is quicker to market and lower in cost.

Features

• Scaleable Bandwidth: 25 - 165MHz Flexible

• Graphics Controller Interface: 12-bit or 24-bit

mode 1 pixel/clock inputs

• Flexible Input Clocking: Single clock single

edge (24-bit), Single clock dual edge (12-/24-

bit), Dual clock single edge (12-bit)

• I2C Slave Programming Interface up to 100kHz

• Low Voltage Interface: 3.3V with option for 1.0

to 3.0V Low Voltage Signal Mode

• Monitor Detection supported through hot plug

and receiver detection

• De-skewing Option varies input clock to input

data timing

• Low Power: 3.3V operation (120mA max.) and

Power Down mode (1mA max.)

• Cable Distance Support: over 5m with twisted

pair and fiber-optics ready

• Compliant with DVI 1.0 (DVI is backwards

compliant with VESA® P&DTM and DFP)

• Standard and Pb-free packages (see pg 29)

SiI 164 Pin Diagram

VCC

VREF

HSYNC

VSYNC

CTL3/A3/DK3

CTL2/A2/DK2

CTL1/A1/DK1

EDGE/HTPLG

PD#

MSEN

VCC

ISEL/RST#

DSEL/SDA

BSEL/SCL

GND

PGND

PVCC1

EXT_SWING

AGND

TXC-

TXC+

AVCC

TX0-

TX0+

AGND

TX1-

TX1+

AVCC

TX2-

TX2+

VCC

RESERVED

DKEN

D23

D22

D21

D20

D19

D18

D17

D16

D15

D14

D13

D12

GND

PVCC2

D11

D10

IDCK-

IDCK+

GND

SiI

164

64-Pin TQFP

(Top View)

AGND

Figure 1. Pin Diagram for SiI 164

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 2

Functional Description

The SiI 164 is a DVI 1.0 compliant PanelLink transmitter in a compact package. It provides 24-bit data Input to

allow for panel support up to UXGA resolution. Figure 2 shows the functional blocks of the chip.

Registers

Configuration

Logic Block

SCL

SDA

EDGE/HTPLG

BSEL/SCL

DSEL/SDA

CTL/A/DK[3:1]

Slave

Machine

Data Capture

Logic Block

D[23:0]

IDCK+

IDCK-

VSYNC

HSYNC

TXC+

TX0+

TX1+

TX2+

VREF

MSEN

PanelLink

Digital

core

ISEL/RST

EXT_SWIN

DKEN

A[3:1]

Figure 2. Functional Block Diagram

PanelLink TMDS Digital Core

The PanelLink TMDS core encodes video information onto three TMDS differential data lines and the differential

clock. The video data is input by the Data Capture Logic Block, as a 12- or 24-bit bus, using one or two clocks

with one or two edges per clock. An attached monitor may be sensed using the HTPLG pin or internally with

Receiver Sense. This detected state may be output onto the MSEN pin. The device may be powered down using

the PD# pin or with an internal register. The SiI 164 is reset using the ISEL/RST# pin. A resistor tied to the

EXT_SWING pin is used to control the TMDS swing amplitude.

I2C Interface and Registers

The SiI 164 uses a slave I2C interface, capable of running at 100kHz. The slave I2C interface is not 5V tolerant. If

the switching levels from the host are not 3.3V, then a voltage level shifter must be used. See Figure 16 and

Figure 17 on page 24 for a system diagram.

A connected display may be detected using the DVI Hot Plug signal, attached to the HTPLG pin; or with the

Receiver Sense logic internal to the SiI 164. The state of the detection, or an interrupt signal indicating a change

of state, may be sent to the MSEN pin. This is useful to the host controller monitoring the SiI 164.

SiI 164 PanelLink Transmitter

Data Sheet

3 SiI-DS-0021-E

Data Capture Logic

Video data is input to the SiI 164 by way of a 12-bit or 24-bit interface. The functionality of this interface is affected

by several of the configuration register settings, as follows.

• BSEL selects between 12-bit and 24-bit input bus widths.

• DSEL selects between single-edge and dual-edge modes for the input clocks.

• EDGE selects between rising and falling edge on the input clocks.

• CLK+ and CLK- provide the one or two clocks required for latching the input data bus.

• The PD# input selects the chip power down mode and allows for disabling of the TMDS outputs.

The ISEL/RST# input resets the HDCP engine and internal registers and is asserted after power up and receipt of

a stable input pixel clock.

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 4

Electrical Specifications

Absolute Maximum Conditions

Absolute Maximum Conditions are defined as the worst-case conditions the part will tolerate without sustaining

damage. Permanent device damage may occur if absolute maximum conditions are exceeded. Proper operation

under these conditions is not guaranteed. Functional operation should be restricted to the conditions described

under Normal Operating Conditions.

Symbol Parameter Min Typ Max Units

VCC Supply Voltage 3.3V -0.3 4.0 V

VI Input Voltage -0.3 VCC+ 0.3 V

VO Output Voltage -0.3 VCC+ 0.3 V

TJ Junction Temperature (with power applied) 125 °C

TSTG Storage Temperature -65 150 °C

Normal Operating Conditions

Symbol Parameter Min Typ Max Units

VCC Supply Voltage 3.0 3.3 3.6 V

VCCN Supply Voltage Noise 100 mVP-P

TA Ambient Temperature (with power applied) 0 25 70 °C

θJA Thermal Resistance (Junction to Ambient)1 64

°C/W

θJC Thermal Resistance (Junction to Case)1 20

°C/W

Note

1. Airflow at 0m/s.

Digital I/O Specifications

Under normal operating conditions unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

VIH High Swing High-level Input

Voltage

VREF = VCC 2.0 V

VIL High Swing Low-level Input

Voltage

VREF = VCC 0.8 V

VDDQ

2 Low Swing Voltage 1 3.0 V

VSH Low Swing High-level Input

Voltage

VREF = VDDQ/2 VDDQ/2 +

300mV

VSL Low Swing Low-level Input

Voltage

VREF = VDDQ/2 VDDQ/2 –

100mV

VCINL Input Clamp Voltage1 I

CL = -18mA GND -0.8 V

VCIPL Input Clamp Voltage1 I

CL = 18mA VCC + 0.8 V

IIL Input Leakage Current -10 10 µA

VIH High Swing High-level Input

Voltage

VREF = VCC 2.0 V

Notes

1. Guaranteed by design. Voltage undershoot or overshoot cannot exceed absolute maximum conditions

2. VDDQ defines the maximum voltage level of Low Swing input. It is not an actual input voltage. Chip characterization for

Low Swing operation is performed at 1.5V only. Voltage level of Low Swing input should never exceed absolute

maximum rating.

SiI 164 PanelLink Transmitter

Data Sheet

5 SiI-DS-0021-E

DC Specifications

Under normal operating conditions unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

VOD Differential Voltage Single ended

peak to peak amplitude

RLOAD = 50Ω, REXT_SWING = 510Ω 510 550 590 mV

VDOH Differential High-level Output AVCC V

Voltage1

IDOS Differential Output Short Circuit

Current1

VOUT = 0 V 5 µA

IPD# Power-down Current2 0.2 1.0 mA

ICCT Transmitter Supply Current IDCK= 165 MHz, 1-pixel/clock

mode, REXT_SWING = 510Ω,

Worst Case Pattern3

854 1205 mA

Notes

1. Guaranteed by design.

2. Assumes all inputs to the transmitter are not toggling.

3. Black and white checkerboard pattern, each checker is one pixel wide.

4. Measurement taken at VCC = 3.30V.

5. Measurement taken at VCC = 3.60V.

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 6

AC Specifications

Under normal operating conditions unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units Figure

TCIP IDCK Period, 1-pixel/clock 6 40 ns Figure 3

FCIP IDCK Frequency, 1-pixel/clock 25 165 MHz

TCIH IDCK High Time at 165MHz 2.0 ns Figure 3

TCIL IDCK Low Time at 165MHz 2.0 ns Figure 3

TIJIT Worst Case IDCK Clock Jitter2,3 2 ns

TSIDF Data, DE, VSYNC, HSYNC

Setup Time to IDCK falling edge

(Default De-skew Setting)

Single Edge

(DSEL = 0,

EDGE = 0)

1.0 ns

Figure 6

THIDF Data, DE, VSYNC, HSYNC

Hold Time from IDCK falling edge

(Default De-skew Setting)

Single Edge

(DSEL = 0,

EDGE = 0)

0.9 ns

Figure 6

TSIDR Data, DE, VSYNC, HSYNC

Setup Time to IDCK rising edge1

(Default De-skew Setting)

Single Edge

(DSEL = 0,

EDGE = 1)

1.0 ns

Figure 6

THIDR Data, DE, VSYNC, HSYNC

Hold Time from IDCK rising edge1

(Default De-skew Setting)

Single Edge

(DSEL = 0,

EDGE = 1)

0.9 ns

Figure 6

TSID Data, DE, VSYNC, HSYNC

Setup Time to IDCK falling/rising edge1

(Default De-skew Setting)

Dual Edge

(DSEL = 1,

BSEL = 0)

0.6 ns

THID Data, DE, VSYNC, HSYNC

Hold Time from IDCK falling/rising edge1

(Default De-skew Setting)

Dual Edge

(DSEL = 1,

BSEL = 0)

1.3 ns

TDDF VSYNC, HSYNC Delay from DE falling

edge1

1TCIP ns

Figure 7

TDDR VSYNC, HSYNC Delay to DE rising edge1 1TCIP ns

Figure 7

THDE DE high time1 8191TCIP ns Figure 8

TLDE DE low time1 128TCIP ns Figure 8

TSTEP De-skew step size increment DKEN = 0b1 260 ps

TRESET Duration of RESET signal Low required for

valid Reset

10 µs

Figure 5

CL = 10pf 700 ns TI2CDVD SDA Data Valid Delay from SCL high

to low transition3 CL = 400pf 2000 ns

Figure 9

SHLT Differential Swing High-to-Low Transition

Time

RLOAD = 50Ω,

REXT_SWING =

510Ω

170 200 230 ps Figure 4

SLHT Differential Swing Low-to-High Transition

Time

RLOAD = 50Ω,

REXT_SWING =

510Ω

170 200 230 ps Figure 4

Notes

1. Guaranteed by design.

2. Actual jitter tolerance may be higher depending on the frequency of the jitter.

3. All Standard mode I2C (100kHz) timing requirements are guaranteed by design. Fast mode I2C (400kHz) timing

requirements are guaranteed at 10pf loading.

SiI 164 PanelLink Transmitter

Data Sheet

7 SiI-DS-0021-E

Input Timing Diagrams

CIH

CIL

CIP

2.0 V

0.8 V

2.0 V 2.0 V

Figure 3. Clock Cycle High/Low Times

Figure 4. Low Swing Differential Times

ISEL/RST#

VCC

RESET

Figure 5. ISEL/RST# Minimum Timing

LHT

20% V

80% V

HLT

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 8

Figure 6. Input Data Setup/Hold Time to IDCK

Figure 7. VSYNC, HSYNC and CTL[3:1] Delay Time from DE

LDE

HDE

0.8 V

2.0 V

0.8 V

2.0 V

Figure 8. DE High and Low Times

Figure 9. I2C Data Valid Delay (driving Read Cycle data)

D[23:0], DE,

HSYNC,VSYNC

IDCK

SIDF

HIDF

SIDR

HIDR

50 %

50 % 50 %

50 %

DDR

DDF

VSYNC, HSYNC,

CTL[3:1]

0.8 V

0.8 V 0.8 V

0.8 V

VSYNC, HSYNC,

CTL[3:1]

SCL

TI2

I2CDVD

SDA

SiI 164 PanelLink Transmitter

Data Sheet

9 SiI-DS-0021-E

Pin Descriptions

Input Pins

Pin Name Pin # Type Description

D[23:12]

36-47 In

Top half of 24-bit pixel bus.

When BSEL = HIGH,

this bus inputs the top half of the 24-bit pixel bus.

When BSEL = LOW,

these bits are not used to input pixel data. In this mode, the state of D[23:16] is input to the

I2C register CFG. This allows 8-bits of user configuration data to be read by the graphics

controller through the I2C interface (see I2C register definition). When not used D[23:16]

should be tied to ground. D[15:12] are reserved for SiI use only and should be tied to GND.

D[11:0] 50-

55,

58-63

Bottom half of 24-bit pixel bus / 12-bit pixel bus input.

When BSEL = HIGH,

this bus inputs the bottom half of the 24-bit pixel bus.

When BSEL = LOW,

this bus inputs ½ a pixel (12-bits) at every latch edge (both falling and/or rising) of the clock.

IDCK+ 57 In

Input Data Clock +. This clock is used for all input modes.

IDCK- 56 In

Input Data Clock –. This clock is only used in 12-bit mode when dual edge clocking is turned

off (DSEL = LOW). It is used to provide the ODD latching edges for dual clock single edge.

If BSEL = HIGH or DSEL = HIGH,

this pin is unused and should be tied to GND.

DE 2 In

Input Data Enable. This signal qualifies the active data area. DE is always required by the

transmitter and must be high during active display time and low during blanking time.

HSYNC 4 In

Horizontal Sync input control Signal

VSYNC 5 In

Vertical Sync input control signal.

CTL1/A1/DK1

CTL2/A2/DK2

CTL3/A3/DK3

In The use of these multi-function inputs depends on the settings of ISEL/RST# and DKEN.

These inputs are regular high-swing 3.3V CMOS level inputs. These pins contain weak pull-

down resistors so that if left unconnected, they will be LOW.

When ISEL/RST# = LOW, DKEN = LOW

General Purpose Input CTL[3:1] pins are active, for backward compatibility. These pins must

be used to send DC signals only during the blanking time.

When ISEL/RST# = LOW, DKEN = HIGH

DK[3:1] are active, these inputs are used to select the De-skewing setting for the input bus.

When ISEL/RST# = HIGH, DKEN = HIGH

A[3:1] are active, these bits are used to set the lower 3 bits of the I2C device address.

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 10

Pin Descriptions (cont’d)

Configuration Pins

Pin Name Pin # Type Description

MSEN 11 Out

Monitor Sense. This pin is an open collector output. The behavior of this output depends on

whether I2C interface active:

I2C bus inactive (ISEL/RST# = LOW)

HIGH level indicates a powered on receiver is detected at the differential outputs.

A LOW level indicates a powered on receiver is not detected.

I2C bus is enabled (ISEL/RST# = HIGH)

The output is programmable through the I2C interface (see I2C Register Definitions).

An external 5K pull-up resistor to VDDQ is required on this pin.

ISEL/RST# 13 In I2C Interface Select.

ISEL/RST#=HIGH,

I2C interface is active.

ISEL/RST#=LOW,

I2C is inactive and the chip configuration is read from the configuration strapping pins. This pin

also acts as an asynchronous reset to the I2C interface controller. The reset is active when this

input is held LOW.

Note: When the I2C interface is active, DKEN must be set HIGH.

BSEL/SCL 15 In Input bus select / I2C clock. This pin is an open collector input. If I2C bus is enabled

(ISEL/RST# = HIGH), then this pin is the I2C clock input. If the I2C is disabled (ISEL/RST# =

LOW), then this pin selects the input bus width.

Input Bus Select:

HIGH selects 24-bit input mode

LOW selects 12-bit input mode

DSEL/SDA 14 In/Out

Dual edge clock select / I2C Data. This pin is an open collector input/output. If I2C bus is

enabled (ISEL/RST# = HIGH), then this pin is the I2C data line. If the I2C bus is disabled

(ISEL/RST# = LOW), then this pin selects whether single clock dual edge is used.

Dual Edge clock select:

When HIGH, IDCK+ latches input data on both falling and rising clock edges.

When LOW, IDCK+/IDCK- latches input data on only falling or rising clock edges.

In 24-/12-bit mode:

If HIGH (dual edge), IDCK+ is used to latch data on both falling and rising edges.

If LOW (single edge), IDCK+ latches 1st half data and IDCK- latches 2nd half data.

EDGE/

HTPLG

9 In

Edge select / Hot Plug input. If the I2C bus is enabled (ISEL/RST# = HIGH), then this pin is

used to monitor the “Hot Plug” detect signal (Please refer to the DVITM or VESA® P&DTM and

DFP standards). This Input is ONLY 3.3V tolerant and has no internal de-bouncer circuit.

If I2C bus is disabled (ISEL/RST# = LOW), then this pin selects the clock edge that will latch

the data. How the EDGE setting works depends on whether dual or single edge latching is

selected:

Dual Edge Mode (DSEL = HIGH)

EDGE = LOW, the primary edge (first latch edge after DE is asserted) is the falling edge.

EDGE = HIGH, the primary edge (first latch edge after DE is asserted) is the rising edge.

Note: In 24-bit Single Clock Dual Edge mode, EDGE is ignored.

Single Edge Mode (DSEL = LOW)

EDGE = LOW, the falling edge of the clock is used to latch data.

EDGE = HIGH, the rising edge of the clock is used to latch data.

DKEN 35 In

De-skewing enable.

I2C mode (ISEL/RST# = HIGH)

DKEN pin must be set to HIGH. DK[3:1] pins are ignored and the De-skewing increments are

selected through the I2C interface (see the I2C register definitions).

Non I2C mode (ISEL/RST# = LOW)

DKEN = LOW, then default De-skewing setting is used.

DKEN = HIGH, then DK[3:1] is used as the De-skewing setting. The De-skewing increments

are TSTEP. Please see Data De-skew Feature for an illustration.

SiI 164 PanelLink Transmitter

Data Sheet

11 SiI-DS-0021-E

Pin Descriptions (cont’d)

Input Voltage Reference Pin

Pin Name Pin # Type Description

VREF 3 Analog In Input Reference Voltage. Selects the Swing range of the digital inputs, which include only

D[23:0], IDCK+, IDCK-, DE, VSYNC, and HSYNC. Input pins SCL and SDA, RST, BSEL,

DSEL, EDGE and PD# require 3.3V high swing signals and are not changed by the VREF

input.

To set the digital inputs to 3.3V High Voltage Swing, VREF must be set to 3.3V.

To set the digital inputs to Low Voltage Swing, VREF must be set to ½ of VDDQ where

VDDQ is swing level of input signal. Thus for DVO mode (1.5V Low Voltage Swing) VREF

should be set to 0.75V and BSEL=LOW.

Power Management Pins

Pin Name Pin # Type Description

PD# 10 In

Power Down (active LOW). A HIGH level indicates normal operation. A LOW level indicates

Power Down mode. In Power Down mode the Analog core is disabled and Output

buffers/pins are tri-stated however the Input buffer/pins and I2C Block for read and write are

active. PD# pin is disabled during I2C mode. PD# should be tied low during I2C mode.

Differential Signal Data Pins

Pin Name Pin # Type Description

TX0+

TX0-

TX1+

TX1-

TX2+

TX2-

Analog

TMDS Low Voltage Differential Signal input data pairs.

These pins are tri-stated when PD# is pulled low.

TXC+

TXC-

Analog

TMDS Low Voltage Differential Signal input clock pair.

These pins are tri-stated when PD# is pulled low.

EXT_SWING 19 Analog Voltage Swing Adjust. A resistor should tie this pin to AVCC. This resistor sets the

amplitude of the voltage swing. A smaller resistor value sets a larger voltage swing and

vice versa. For remote display applications a 510Ω with + 5% (max) tolerance resistor is

recommended. While for notebook computers 680Ω is recommended to ensure voltage

swing is not overdriven over a short cable distance.

Reserved Pins

Pin Name Pin # Type Description

RESERVED 34 In

Must be tied LOW for normal operation.

Power and Ground Pins

Pin Name Pin # Type Description

VCC 1,12,33 Power Digital VCC, must be set to 3.3V nominal.

GND 16,48,64 Ground Digital GND.

AVCC 23,29 Power Analog VCC, must be set to 3.3V nominal.

AGND 20,26,32 Ground Analog GND.

PVCC1 18 Power Primary PLL Analog VCC, must be set to 3.3V nominal.

PVCC2 49 Power Filter PLL Analog VCC, must be set to 3.3V nominal.

PGND 17 Ground PLL Analog GND.

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 12

I2C Registers

I2C Register Mapping

Addr Reset

Value Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

0x00 0x01 VND_IDL

0x01 0x00 VND_IDH

0x02 0x06 DEV_IDL

0x03 0x00 DEV_IDH

0x04 0x00 DEV_REV

0x05 0x00 RSVD

0x06 0x19 FRQ_LOW

0x07 0x64 FRQ_HIGH

0x08 00●●●●

●0

RSVD VEN HEN DSEL BSEL EDGE PD#

0x09 ●000

0●●0 RSVD MSEL TSEL RSEN HTPLG MDI

0x0A 0x90 DK[3:1] DKEN CTL[3:1] RSVD

0x0B ●●●●

●●●● CFG[7:0]

0x0C ●●●0

●●●● SCNT RSVD PLLF[3:0] PFEN

0x0D 0x80 RSVD

0x0E 0x00 RSVD

0x0F 0x00 RSVD

Notes

1. All values are Bit 7 [MSB] and Bit 0 [LSB].

2. Bits and registers bold like this are read only. All others are Read/Write.

3. Bits and registers in italics and bold like this are undefined after RESET, although they are accessible by read or write.

4. RSVD is a reserved register or bit field. It is available for future use by Silicon Image. All RSVD fields are read-only and

are not affected by data written to them.

5. 0x0C is also called the VDJK Register. Default setting for the VDJK register 0x0C is 0x89, which is optimum for most

applications.

I2C Reset values are shown in the column at the left of the table. Bits or registers which have no default value

after power-on, or which have no defined value after RESET, are shown with the symbol ● in the table. All

registers Hexadecimal values use a prefix of ‘0x’. Binary values use a prefix of ‘0b’. To enable the device,

registers 0x08, 0x09, 0x0A and 0x0C must be programmed. A sample programming sequence is listed on page

18 for 12-bit mode.

SiI 164 PanelLink Transmitter

Data Sheet

13 SiI-DS-0021-E

I2C Register Definitions

VND_IDL RO Vendor ID Low byte (01h)

VND_IDH RO Vendor ID High byte (00h)

DEV_IDL RO Device ID Low byte (06h)

DEV_IDH RO Device ID High byte (00h)

DEV_REV RO Device Revision (00h)

FRQ_LOW RO Low frequency limit at 1-pixel/clock mode (MHz) (19h)

FRQ_HIGH RO High frequency limit at 1-pixel/clock mode Max frequency minus 65MHz (MHz) (64h)

PD RW Power Down mode (same function as PD# pin)

0 – Power Down (Default after RESET)

1 – Normal operation

EDGE RW Edge Select (same function as EDGE pin)

0 – Input data is falling edge latched (falling edge latched first in dual edge

mode)

1 – Input data is rising edge latched (rising edge latched first in dual edge

mode)

BSEL RW Input Bus Select (same function as BSEL pin)

0 – Input data bus is 12-bits wide

1 – Input data bus is 24-bits wide

DSEL RW Dual Edge Clock Select (same function as DSEL pin)

0 – Input data is single edge latched

1 – Input data is dual edge latched

HEN RW Horizontal Sync Enable:

0 – HSYNC input is transmitted as fixed LOW

1 – HSYNC input is transmitted as is

VEN RW Vertical Sync Enable:

0 – VSYNC input is transmitted as fixed LOW

1 – VSYNC input is transmitted as is

MDI RW Monitor Detect Interrupt

0 – Detection signal has changed logic level (write one to this bit to clear)

1 – Detection signal has not changed state

HTPLG RO Hot Plug Detect input, the state of HTPLG pin can be read from this bit

RSEN RO Receiver Sense (only available for use in DC coupled systems)

0 – Active/Powered Receiver not detected

1 – Active/Powered Receiver detected

TSEL RW Interrupt Generation Method

0 – Interrupt bit (MDI) is generated by monitoring RSEN

1 – Interrupt bit (MDI) is generated by monitoring HTPLG

MSEL[2:0] RW Select source of the MSEN output pin

000 – Force MSEN outputs high (disabled – default after RESET)

001 – Outputs the MDI bit (interrupt)

010 – Output the RSEN bit (receiver sense detect)

011 – Outputs the HTPLG bit (hotplug detect)

1xx – RESERVED

VLOW RO VREF setting

1 – Indicates High Swing Input Mode

0 – Indicates Low Swing Input Mode

CTL[3:1] RW General purpose inputs (same as CTL[3:1] pins). These bits are only transmitted

during blanking period.

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 14

I2C Register Definitions (cont’d)

CFG[7:0] RO Contains state of inputs D[23:16]. These pins can be used to provide user selectable

configuration data through the I2C bus. Only available in 12-bit mode

PFEN RW PLL Filter Enable in the VDJK Register 0x0C.

1 – To enable PLL Filter (recommended setting)

0 – To disable PLL Filter

PLLF[3:1] RW Set characteristics of PLL filter in VDJK Register 0x0C.

100 – Recommended value

All other values are not recommended.

SCNT RW SYNC Continuous

1 – To enable (recommended setting)

0 – To disable

DK[3:1] RW De-skewing Setting. Increment 260psec.

000 – 1 step -> minimum setup / maximum hold

001 – 2 step

010 – 3 step

011 – 4 step

100 – 5 step -> default (recommended setting)

101 – 6 step

110 – 7 step

111 – 8 step -> maximum setup / minimum hold

Please see Data De-Skew Feature for an illustration

DKEN RW De-skewing Enable through DK[3:1] bits. When DKEN pin is HIGH via pin or set to 1,

then De-skew is enabled. When set to 0 De-skew is disabled. Please see Data De-

skew Feature on page 16 for an illustration.

SiI 164 PanelLink Transmitter

Data Sheet

15 SiI-DS-0021-E

I2C Slave Interface and Address

The SiI 164 slave state machine does not require an internal clock and support only byte read and write. Page

mode is not supported. The 7-bit binary address of the I2C machine is “0111 A3A2A1R” where R =1 sets a read

operation while R=0 sets a write operation. Please see Figure 10 for a Byte Read operation and Figure 11 for a

byte write operation. For more detailed information on I2C protocols please refer to I2C Bus Specification version

2.1 available from Philips Semiconductors Inc.

When ISEL/RST# = HIGH and DKEN = HIGH, pins 6,7,8 functions as A[3:1]. Each pin can be set to HIGH or LOW

to select a desired I2C address for the SiI 164. To set the SiI 164 to 0x72, tie pin 7 and 6 to ground and pull pin 8 to

VCC via 2.2K resistor. The recommended setting is to tie pins 6,7 and 8 to ground to set “000” or address 0x70 in

I2C mode .

Slave

Address Register Address Slave

Address

Data

Stop

Start

Bus Activity :

SiI 164

Bus Activity :

Master

SDA Line

Figure 10. I2C Byte Read

Slave

Address Address Data

Stop

Start

Bus Activity :

SiI 164

Bus Activity :

Master

SDA Line

Figure 11. I2C Byte Write

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 16

Data De-skew Feature

The de-skew feature allows adjustment of the clock-to-data delay on the input of the SiI 164. When driven by a

chip with clock and data timings which do not meet the setup and hold time requirements of an SiI 164, the de-

skew register value can be modified to position the clock in the middle of the valid data time and meet the input

setup and hold times. As shown in Figure 12, changing the DK[3:1] value from 0b100 to 0b111 delays the internal

clock by approximately 750ps to 900ps, increasing setup time and reducing hold time. This is useful when the

input clock, IDCK, arrives too early.

The default values for DK[3:1] are shown in Table 1, along with approximate times per setting. Note that the

default is different when enabling I2C mode (ISEL/RST#=HIGH) versus non-I2C mode (ISEL/RST#=LOW).

Positive values of TCD move the clock later, increasing setup time. Negative values of TCD move the clock earlier,

increasing hold time.

Where:

CD is the amount of setup/hold timing variation

DK[3:1] is the setting of the de-skew configuration pins or I2C registers

Table 1. Data De-Skew Estimated Values

DK[3:1] De-Skew Time

TCD

0b111 +0.75ns to +0.90ns

0b110 +0.50ns to +0.70ns

0b101 +0.20ns to +0.35ns

0b100 0 Default De-Skew

0b011 -0.20ns to -0.35ns

0b010 -0.50ns to –0.70ns

0b001 -0.75ns to –0.90ns

0b000 -1.0ns to -1.2ns

TCD

CLK+

CLK-

D K [3 :1] 0b000 0b100 0b111

D [2 3:0 ],

DE, VSY NC,

HSYNC,

CTL[3:1]

-TCD

default

Figure 12. SiI 164 Data De-skew Feature Timing

SiI 164 PanelLink Transmitter

Data Sheet

17 SiI-DS-0021-E

Data Latching Modes

SiI 164 can be set to different to operate in either 12-bit or 24-bit input mode. In either mode the SiI 164 can be

set to latch data at either rising or falling edge of the clock or support dual edge clocking mode. Figure 13

illustrates the latching edge for a 12-bit data input (BSEL = 0) by changing DSEL and EDGE option. Clock edges

represented by arrows signify the latching edge. For Dual Edge mode, the dark arrows indicate the primary latch

edge.

IDCK+

D[11:0]

N-1

IDCK+

IDCK-

IDCK+

IDCK-

DSEL = 1

DSEL = 0

DSEL = 1

DSEL = 0

EDGE = 1

EDGE = 0

L = Low half pixel

H = High half pixel

First Latch Edge

Figure 13. 12-bit Input Data Latching

Figure 14 illustrates the latching edge for a 24-bit data input (BSEL=1) with DSEL and EDGE option. EDGE pin

has no affect in 24-bit Single Clock Dual Edge Mode.

First Latching Edge

D[23:0]

N-1

DSEL = 1, EDGE = 0

DSEL = 1, EDGE = 1

IDCK+

DSEL =0, EDGE = 1

IDCK+

DSEL = 0, EDGE = 0

IDCK+

Figure 14. 24-bit Input Data Latching

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 18

I2C Programming Sequence

To program the SiI 164 in data latched on 12-bit mode Dual Edge Clock with Primary Edge as the rising edge or

falling edge, De-skew enabled with Hotplug based monitor detection use the following sample programming

sequence listed in Table 2. It is important to note that the suggested I2C address for SiI 164 be set to 0x70 by

tying pins A1, A2 and A3 to ground.

Table 2. Sample Programming Sequence for SiI 164 in 12-bit Mode

0x08

Setting 1: 0x30

Setting 2: 0x32

Setting 1: Enable HEN, VEN, 1st data

latched on falling edge with PD low until

all registers are programmed.

Setting 2: Enable HEN, VEN, 1st data

latched on rising edge with PD low until

all registers are programmed.

0x09 0x30

Monitor detection mode via Hotplug

input.

0x0A 0x90

De-skew enabled with default 100 value.

CTL is not used.

0x0C 0x89

SCNT, PLL Filter Enable and PLL

Bandwidth Filter set to default.

0x08

Setting 1: 0x31

Setting 2: 0x33

Setting 1: Recover from Power Down

mode and enable output.

Setting 2: Recover from Power Down

mode and enable output.

Enabling Hot Plug Detection Mode

As documented in the VESA Digital Flat Panel Standard, all monitors are required to support Hot Plug Detection

but support is optional for the host. The SiI 164 supports the Hot Plug Detect feature. In I2C mode, pin 9 functions

as HTPLG input. It should be noted that the HTPLG pin on the SiI 164 is only 3.3V tolerant therefore HTPLG

voltage level from the DVI connector should be level shifted or clamped at 3.3V.

When the voltage level at the HTPLG pin is 3.3V, the HTPLG bit will be set to 1. To output the HTPLG bit via the

MSEN pin, register MSEL[2:0] should be programmed to 0b011.

The SiI 164 can also be programmed to enable the Hot Plug Detection Mode via the Receiver Sense function. In

this mode, HTPLG pin is not required. By programming MSEL[2:0] to 0b010, SiI 164 will output the RSEN=1 bit

though the MSEN pin when the SiI 164 is connected to a powered receiver.

SiI 164 PanelLink Transmitter

Data Sheet

19 SiI-DS-0021-E

Non-I2C/Strap Mode Configuration

The SiI 164 can be set to program itself at power up without writing any SiI 164 registers via I2C. The SiI 164 is

extremely flexible and can be set to operate in any input format that can be set in I2C mode. In non I2C mode,

specific configuration pins need to be strapped to either high or low to set the desired mode. Figure 15 provides a

schematic example of all the pins that can be configured to enable the various modes in non I2C mode. Table 3

lists resistors to be stuffed for a specific mode.

R18

15K

3.3V

R10

33K

BSEL

R11

33K

3.3V

R6 330 EDGE

DKEN

DK1

33K

2.2K

R15 0

2.2K

R12 330

D[11..0]

1.5V or VDDQ

D10

R17

2.2K

R14 0

R4 330

AVCC

R13 0

DK3

DK2

VREF

R19

15K

R16

510

Sil 164

VREF

DK3

DK2

DK1

EDGE/CHG/SIN

ISEL/RST

DSEL/SDA

BSEL/SCL

EXT_RES

RSVD

DKEN

D23

D22

D21

D20

D19

D18

D17

D16

D15

D14

D13

D12

D11

D10

2.2K

3.3V

D11

33K

DSEL

33K

R5 330

Figure 15. Non- I2C/Strap Mode Schematic Example

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 20

Non-I2C/Strap Mode Configuration (cont’d)

ISEL/RST# and RSVD pins must always be tied to ground for strap or non- I2C mode. PD# must be tied high or

the SiI 164 will still be in Power Down mode when VCC is applied.

In Figure 15 Block A corresponds to the upper 12-bits (D [23:12]) of the SiI 164. When not in use, they should

always be tied to ground. Block B controls the Input Bus data width, Dual Edge Clock Select and Edge Select.

IDCK- is only used in 12-bit mode. In 24-bit mode or Dual Edge Clock select IDCK- should be tied to ground.

Block C controls the De-skew options. Block D determines the input voltage level swing. A full description of

each pin can be found in the Pin Description section of this document.

Table 3. Non-I2C/Strap Mode Options

MODE BLOCK A BLOCK B BLOCK C BLOCK D

1. 24-bit1

2. Single Clock

3. Dual Edge

4. Falling Edge

latching 1st pixel

5. De-skewing

enabled to 100

6. High Voltage

Swin

Connect D[23:12] to

Graphics Host

Stuff only

R1, R2, R6

Stuff only

R8, R13, R14, R11

Stuff Only

R17

1. 24-bit

2. Single Clock

3. Single Edge

4. Falling Edge

5. De-skewing

disabled

6. High Voltage

Swing.

Connect D[23:12] to

Graphics Host

Stuff only

R1, R5, R6

Stuff only

R12, R13, R14, R15

Stuff Only

R17

1. 12-bit2

2. Single Clock

3. Dual Edge

4. Rising Edge of

IDCK+ latching 1st

½ pixel

5. De-skewing

disabled

6. High Voltage

Swing.

Ground D[23:12] Stuff only

R4, R2, R3

Stuff only

R12, R13, R14, R15

Stuff Only

R17

1. 12-bit3

2. Dual Clock

3. Dual Edge,

4. Falling Edge of

IDCK+ latching 1st

½ pixel

5. De-skewing

enabled to 100

6. Low Swing Mode

Ground D[23:12] Stuff only

R4, R5, R6

Stuff only

R8, R13, R14, R11

Stuff Only

R18, R19

Notes

1. In 24-bit IDCK+ is input clock. IDCK- should be tied to ground.

2. In 12-bit dual edge (non-DVO) mode, IDCK- is not used.

3. This setting is equivalent to DVO mode. In DVO mode both IDCK+ and IDCK- must be connected.

SiI 164 PanelLink Transmitter

Data Sheet

21 SiI-DS-0021-E

TFT Panel Data Mapping

The following TFT data mapping tables are strictly listed for single link TFT applications only. SiI 143B, SiI 151B,

SiI 153B and SiI 161B all have the same pinout. As such mapping will be the same when SiI 143B or SiI 151B or

SiI 153B is used in place of SiI 161B.

Table 4. One Pixel/Clock Input/Output TFT Mode - VESA P&D and FPDI-2 Compliant

TFT VGA Output Tx Input Data Rx Output Data TFT Panel Input

24-bpp 18-bpp 160 164 161B 141B 24-bpp 18-bpp

B0 DIE0 D0 QE0 Q0 B0

B1 DIE1 D1 QE1 Q1 B1

B2 B0 DIE2 D2 QE2 Q2 B2 B0

B3 B1 DIE3 D3 QE3 Q3 B3 B1

B4 B2 DIE4 D4 QE4 Q4 B4 B2

B5 B3 DIE5 D5 QE5 Q5 B5 B3

B6 B4 DIE6 D6 QE6 Q6 B6 B4

B7 B5 DIE7 D7 QE7 Q7 B7 B5

G0 DIE8 D8 QE8 Q8 G0

G1 DIE9 D9 QE9 Q9 G1

G2 G0 DIE10 D10 QE10 Q10 G2 G0

G3 G1 DIE11 D11 QE11 Q11 G3 G1

G4 G2 DIE12 D12 QE12 Q12 G4 G2

G5 G3 DIE13 D13 QE13 Q13 G5 G3

G6 G4 DIE14 D14 QE14 Q14 G6 G4

G7 G5 DIE15 D15 QE15 Q15 G7 G5

R0 DIE16 D16 QE16 Q16 R0

R1 DIE17 D17 QE17 Q17 R1

R2 R0 DIE18 D18 QE18 Q18 R2 R0

R3 R1 DIE19 D19 QE19 Q19 R3 R1

R4 R2 DIE20 D20 QE20 Q20 R4 R2

R5 R3 DIE21 D21 QE21 Q21 R5 R3

R6 R4 DIE22 D22 QE22 Q22 R6 R4

R7 R5 DIE23 D23 QE23 Q23 R7 R5

Shift CLK Shift CLK IDCK IDCK ODCK ODCK Shift CLK Shift CLK

VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE DE DE DE

For 18-bit mode, the Flat Panel Graphics Controller interfaces to the transmitter exactly the same as in the 24-bit

mode; however, 6 bits per channel (color) are used instead of 8. It is recommended that unused data bits be tied

low. As can be seen from the above table, the data mapping for less than 24-bit per pixel interfaces are MSB

justified. The data is sent during active display time while the control signals are sent during blank time. Note that

the three data channels (CH0, CH1, CH2) are mapped to Blue, Green and Red data respectively.

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 22

Table 5. 24-bit One Pixel/Clock Input with 24-bit Two Pixels/Clock Output TFT Mode

TFT VGA Output Tx Input Data Rx Output Data TFT Panel Input

24-bpp 160 164 161B 24-bpp

B0 DIE0 D0 QE0 B0 - 0

B1 DIE1 D1 QE1 B1 - 0

B2 DIE2 D2 QE2 B2 - 0

B3 DIE3 D3 QE3 B3 - 0

B4 DIE4 D4 QE4 B4 - 0

B5 DIE5 D5 QE5 B5 - 0

B6 DIE6 D6 QE6 B6 - 0

B7 DIE7 D7 QE7 B7 - 0

G0 DIE8 D8 QE8 G0 - 0

G1 DIE9 D9 QE9 G1 - 0

G2 DIE10 D10 QE10 G2 - 0

G3 DIE11 D11 QE11 G3 - 0

G4 DIE12 D12 QE12 G4 - 0

G5 DIE13 D13 QE13 G5 - 0

G6 DIE14 D14 QE14 G6 - 0

G7 DIE15 D15 QE15 G7 - 0

R0 DIE16 D16 QE16 R0 - 0

R1 DIE17 D17 QE17 R1 - 0

R2 DIE18 D18 QE18 R2 - 0

R3 DIE19 D19 QE19 R3 - 0

R4 DIE20 D20 QE20 R4 - 0

R5 DIE21 D21 QE21 R5 - 0

R6 DIE22 D22 QE22 R6 - 0

R7 DIE23 D23 QE23 R7 - 0

QO0 B0 - 1

QO1 B1 - 1

QO2 B2 - 1

QO3 B3 - 1

QO4 B4 - 1

QO5 B5 - 1

QO6 B6 - 1

QO7 B7 - 1

QO8 G0 - 1

QO9 G1 - 1

QO10 G2 - 1

QO11 G3 - 1

QO12 G4 - 1

QO13 G5 - 1

QO14 G6 - 1

QO15 G7 - 1

QO16 R0 - 1

QO17 R1 - 1

QO18 R2 - 1

QO19 R3 - 1

QO20 R4 - 1

QO21 R5 - 1

QO22 R6 - 1

QO23 R7 - 1

Shift CLK IDCK IDCK ODCK Shift CLK/2

VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE

SiI 164 PanelLink Transmitter

Data Sheet

23 SiI-DS-0021-E

Table 6. 18-bit One Pixel/Clock Input with 18-bit Two Pixels/Clock Output TFT Mode

TFT VGA Output Tx Input Data Tx Output Data TFT Panel Input

18-bpp 160 164 161B 141B 18-bpp

DIE0 D0 QE0

DIE1 D1 QE1

B0 DIE2 D2 QE2 Q0 B0 - 0

B1 DIE3 D3 QE3 Q1 B1 - 0

B2 DIE4 D4 QE4 Q2 B2 - 0

B3 DIE5 D5 QE5 Q3 B3 - 0

B4 DIE6 D6 QE6 Q4 B4 - 0

B5 DIE7 D7 QE7 Q5 B5 - 0

DIE8 D8 QE8

DIE9 D9 QE9

G0 DIE10 D10 QE10 Q6 G0 - 0

G1 DIE11 D11 QE11 Q7 G1 - 0

G2 DIE12 D12 QE12 Q8 G2 - 0

G3 DIE13 D13 QE13 Q9 G3 - 0

G4 DIE14 D14 QE14 Q10 G4 - 0

G5 DIE15 D15 QE15 Q11 G5 - 0

DIE16 D16 QE16

DIE17 D17 QE17

R0 DIE18 D18 QE18 Q12 R0 - 0

R1 DIE19 D19 QE19 Q13 R1 - 0

R2 DIE20 D20 QE20 Q14 R2 - 0

R3 DIE21 D21 QE21 Q15 R3 - 0

R4 DIE22 D22 QE22 Q16 R4 - 0

R5 DIE23 D23 QE23 Q17 R5 - 0

QO0

QO1

QO2 Q18 B0 - 1

QO3 Q19 B1 - 1

QO4 Q20 B2 - 1

QO5 Q21 B3 - 1

QO6 Q22 B4 - 1

QO7 Q23 B5 - 1

QO8

QO9

QO10 Q24 G0 - 1

QO11 Q25 G1 - 1

QO12 Q26 G2 - 1

QO13 Q27 G3 - 1

QO14 Q28 G4 - 1

QO15 Q29 G5 - 1

QO16

QO17

QO18 Q30 R0 - 1

QO19 Q31 R1 - 1

QO20 Q32 R2 - 1

QO21 Q33 R3 - 1

QO22 Q34 R4 - 1

QO23 Q35 R5 - 1

Shift CLK IDCK IDCK ODCK Shift CLK/2 Shift CLK/2

VSYNC VSYNC VSYNC VSYNC VSYNC VSYNC

HSYNC HSYNC HSYNC HSYNC HSYNC HSYNC

DE DE DE DE DE DE

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 24

Design Recommendations

1.5V to 3.3V I2C Bus Level-Shifting

To program the SiI 164 via I2C mode SDA and SCL swing level must be 3.3V. DVO sources have I2C swing of

1.5V. To ensure proper initialization of the SiI 164 a bi-directional voltage level-shifting circuit between the SiI 164

I2C bus and the VGA or driving source should be implemented. Two suggested components that can be used to

achieve this is by using either a dual N-channel transistor like Fairchild Semiconductor’s NDC7002N or the Philips

GTL2010 High Speed Bus Switch. Refer to Figure 16 for a schematic example using a dual N-channel transistor

for translating an I2C 1.5V signal to 3.3V I2C signal and vice versa.

1.5V

1.5V I

C DATA FROM VGA

2.2K

2.9V 3.3V

1K G

S D

2N7002

1.5V I

C CLK FROM VGA

3.3V2.9V

3.3V I

C CLK TO SiI 164

2.2K

3.3V I

C DATA TO SiI 164

S D

2N7002

Figure 16. I2C Bus Voltage Level-Shifting using Fairchild NDC7002N

Figure 17 illustrates a schematic example using the Philips GTL 2010 to achieve a 1.5V to 3.3V bi-directional

level-shift.

1.5V I

C DATA FROM VGA

3.3V I

C DATA TO SiI 164

2.2K

3.3V I

C CLK TO SiI 164

3.3V

200K

1.5V

1.5V I

C CLK FROM VGA

GTL2010

GND

SREF

GREF

DREF

D10

S10

Figure 17. I2C Bus Voltage Level Shifting using Philips GTL 2010

SiI 164 PanelLink Transmitter

Data Sheet

25 SiI-DS-0021-E

Voltage Ripple Regulation

The power supply to PVCC is very important to the proper operation of the Transmitter chips. PVCC does not

draw much current so any voltage regulator that can supply 50mA or more is sufficient. Two suggested voltage

regulators are TL431 from Texas Instruments or LM317 from National Semiconductor. Two examples are shown

in Figure 18 and Figure 19

(5V) V

out

(3.3V) to PVCC1

and PVCC2

TL431

100-150 ohms

1K ohms

3K ohms

ref

Cathode

Anode

Ref

Figure 18. Volt age Regulation using TL431

Decoupling and bypass capacitors are also involved with power supply connections, as described in detail in

Figure 20 and Figure 21.

out

(3.3V) to PVCC1

and PVCC2

(5V)

240 ohms

390 ohms

OUT

ADJ

LM317EMP

Figure 19. Volt age Regulation using LM317

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 26

Decoupling Capacitors

Designers should include decoupling and bypass capacitors at each power pin in the layout. These are shown

schematically in Figure 21. Place these components as closely as possible to the SiI 164 pins, and avoid routing

through vias if possible, as shown in Figure 20, which is representative of the various types of power pins on the

transmitter.

VCC

Ferrite

Via to GND

VCC

GND

Figure 20. Decoupling and Bypass Capacitor Placement

VCCPIN

C1 C2

VCC

Figure 21. Decoupling and Bypass Schematic

The values shown in Table 7 are recommendations that should be adjusted according to the noise characteristics

of the specific board-level design. Pins in one group (such as VCC) may share C2, L1, and C3, each pin having

C1 placed as closely to the pin as possible.

Table 7. Recommended Components for Bypass and Decoupling Circuits

C1 C2 C3 L1

100 – 300 pF 2.2 – 10 µF 10 µF 200+ Ω

SiI 164 PanelLink Transmitter

Data Sheet

27 SiI-DS-0021-E

Series Damping Resistors on Outputs

Series resistors are effective in lowering the data-related emissions and reducing reflections. Series resistors with

suggested value of 22Ω or 33Ω should be placed close to the output pins of the VGA Source or Graphics chip, as

shown in Figure 22.

D[23..0]

VGA

Figure 22. Series Input Damping Resistors for Driving Source

Differential Trace Routing

The routing for the SiI 164 chip is relatively simple since no spiral skew compensation is needed. However, a few

small precautions are required to achieve the full performance and reliability of DVI.

The Transmitter can be placed fairly far from the output connector, but care should be taken to route each

differential signal pair together and achieve impedance of 100Ω between the differential signal pair. However,

note that the longer the differential traces are between the transmitter and the output connector, the higher the

chance that external signal noise will couple onto the low-voltage signals and affect image quality.

Do not split or have asymmetric trace routing between the differential signal pair. Vias are very inductive and can

cause phase delay problems if applied unevenly within a differential pair. Vias should be minimized or avoided if

possible by placing all differential traces on the top layer of the PCB.

Figure 23 illustrates an incorrect routing of the differential signal from the SiI 164 to the DVI connector. Figure 24

illustrates the correct method to route the differential signal from the SiI 164 to the DVI connector. Figure 25

illustrates recommended routing for differential traces at the DVI connector.

Figure 23. Example of Incorrect Differential Signal Routing

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 28

Figure 24. Example of Correct Differential Signal Routing

TxC-

TxC+

Tx0-

Tx0+

Tx1-

Tx1+

Tx2-

Tx2+

1724

Figure 25. Differential Trace Routing to DVI Connector(Top Side View)

SiI 164 PanelLink Transmitter

Data Sheet

29 SiI-DS-0021-E

Package Dimensions and Marking Specification

SiIDDDDDD

LLLLLL.LLLL

YYWW

X.XX

Device #

Lot #

Date Code

SiI Rev. #

E1 F1

JEDEC Package Code MS-026ACD

typ max

A Thickness 1.20

A1 Stand-off 0.15

A2 Body Thickness 1.00 1.05

D1 Body Size 10.00

E1 Body Size 10.00

F1 Footprint 12.00

G1 Footprint 12.00

L1 Lead Length 1.00

b Lead Width 0.22

c Lead Thickness 0.20

e Lead Pitch 0.50

Dimensions in millimeters.

Overall thickness A=A1+A2.

Device Device Number

DDDDDDDDD

Standard SiI164CT64

Pb-Free SiI164CTG64

Legend Description

LLLLLL.LLLL Lot Number

YY Year of Mfr

WW Work Week of Mfr.

X.XX Revision

Figure 26. 64-pin TQFP Package Dimensions (JEDEC code MS-026ACD)

Ordering Information

Standard Part Number: SiI164BCT64

Pb-Free Part Number: SiI164CTG64('G' designates Pb-free packaging)

SiI 164 PanelLink Transmitter

Data Sheet

SiI-DS-0021-E 30

Silicon Image, Inc. Tel: (408) 616-4000

1060 E. Arques Avenue Fax: (408) 830-9530

Sunnyvale, CA 94085 E-mail: salessupport@SiImage.com

USA Web: www.siliconimage.com