SERIES: 3003 9th Avenue SW
PO Box 50
Watertown, SD 57201
MGDQ6 Toll free: 888-978-2638
Ph: 605-886-3326
Fax: 605-886-8995
Series
Number
Units
L
W
H
X
Y
Z
A
B
C
inches0.492"0.492"0.315"0.315"0.087"0.197"0.202"0.084"0.307"
[ mm ]
[ 12.50 ]
[ 12.50 ]
[ 8.00 ]
[ 8.00 ]
[ 2.20 ]
[ 5.00 ]
[ 5.13 ]
[ 2.13 ]
[ 7.80 ]
LDCR ISAT Tolerance
µH
W
ASuffix
0.470.002035.000M
260°C Maximum reflow temperature per J-STD020
0.75
0.0025
33.00
M
Terminal Plating is Gold Flash over Ni 1.50.00325.00M
2.40.0128.00M
3.50.0147.50M
4.70.01613.50M
6.10.0186.60M
7.6
0.020
5.90
M
100.0225.40M
120.0254.90M
150.0274.50M
180.0403.90M
220.0443.60M
270.0463.40M
330.0653.00M
390.0732.75M
470.1002.50M
560.1102.35M
680.1402.10M
82
0.160
1.95
M
1000.2201.70M
1200.2501.60M
1500.2801.42M
1800.3501.30M
2200.3901.16M
2700.5601.06M
3300.6400.95M
3900.7000.88M
4700.9800.79M
5601.0700.93M
6801.4600.67M
820
1.640
0.60
M
1000
1.820
0.55
M
Contact CoEv for additional inductance values
Call Toll Free: 888-978-2638 Website: www.tycopowercomponents.com
Maximum DimensionsReference Dimensions
MGDQ6
Low Profile, High Current Power Inductors
Part Number
MGDQ6-00001
Lead Free
MGDQ6
MGDQ6-00002
MGDQ6-00006
MGDQ6-00007
MGDQ6-00003
MGDQ6-00004
MGDQ6-00005
MGDQ6-00008
MGDQ6-00009
MGDQ6-00010
MGDQ6-00011
MGDQ6-00012
MGDQ6-00013
MGDQ6-00014
MGDQ6-00015
MGDQ6-00016
MGDQ6-00017
MGDQ6-00018
MGDQ6-00019
MGDQ6-00027
MGDQ6-00020
MGDQ6-00021
MGDQ6-00022
MGDQ6-00023
MGDQ6-00024
MGDQ6-00025
MGDQ6-00026
MGDQ6-00032
MGDQ6-00033
MGDQ6-00028
MGDQ6-00029
MGDQ6-00030
MGDQ6-00031
Specifications subject to change
B
A
C B
Suggested Land Pattern
H
Z
X
Y
W
L
XXX
Suffix
Code
Features:
High energy storage and low resistance
Reliable surface mounting, flat top for pick
and place.
Smaller real estate than other common
inductors.
Robust temperature deflection to prevent
damage during solder reflow.
Tape and Reel mechanical specifications
available upon request.
Operating Temperature -40°C to +85°C.
Highly resistive core for EMI suppression
applications.
Notes:
Inductance measured at 100kHz and 250mVrms.
Isat is a maximum applied AC + DC current.
Isat current is applied to produce a typical 35%
drop in nominal inductance.
Tolerance suffix of M = ±20%.
DCR is a maximum at 25°C.
1
2
Schematic Diagram
Pin 1 Location
Series
Reel dimensions
Reel
Carton (Box)
Packaging
Number
Units
A
B
C
D
Qty
Qty
Specification
in.12.99"3.94"1.16"0.098"
[mm]
[ 330 ]
[ 100.0 ]
[ 29.5 ]
[ 2.50 ]
SeriesW ±0.3P ±0.1P0 ±0.1P2 ±0.1 K0 ±0.05 T ±0.05A0 ±0.1
24.016.04.002.008.250.3512.6
Sheet 2 of 6
90-0054
Customer Packaging Specifications
For Print Distribution to Customers
MGDQ6300
Revision
A0
Series
MGDQ6
MGDQ6
1800
P0
K0
T
P
P2
W
A0
A 2
13 0.5
1.0
2 0.5
21 0.8
C 1
B 1
D 0.5
A MAX.
C MAX.
D MAX.
B MIN.
2 ±0.5
PACKAGING NOTE: Only pressure sensitive cover tape is to be used.
Dimensions are in millimeters unless specified.
DDD
PART
FIGURE 1
CARRIER TAPE AND PART
CARRIER TAPE
COVER
TAPE
SPROCKET
HOLES
PART WILL EITHER HAVE
3 DIGIT CODE OR THREE DOT CODE
PART SHOULD BE ORIENTED
AS SHOWN WHERE "DDD"
INDICATES THE DIRECTION
OF PRINT FOR THE THREE
DIGIT CODE, THE DOTS SHOULD
BE ARRANGED AS SHOWN.
Item
Specification
Test Method/Condition
Environmental
Static Humidity
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
Storage Life
After exposure part remains within
specified electrical parameters for
L, Q and DCR.
Temperature Cycle
After exposure part remains within
10 cycles (Air to Air) 1 cycle shall consist of:
specified electrical parameters for
30 minutes exposure to +85°C
L, Q and DCR.
30 minutes exposure to -40°C
Allow 20 minutes transition between extremes.
Temperature Shock
After exposure part remains within
10 cycles (Air to Air) 1 cycle shall consist of:
specified electrical parameters for
30 minutes exposure to -55°C
L, Q and DCR.
30 minutes exposure to +125°C
15 seconds maximum transition between temperatures
IR Reflow
10 seconds at 260°C max.
Post test parts shall pass all electrical specifications after reflow.
There shall be no visible signs of solder flow or leakage
from the part.
General
Storage Temperature
Range -40°C to +85°C
Operating
Temperature Range -40°C to +85°C
Flammability
IEC 695-2-2
Withstands needle-flame test
Other
Vibration
After exposure part remains within
1 cycle of 30 minutes of the following:
specified electrical parameters for
5 - 7 Hz constant displacement of 0.75 inches, 5 minutes
L, Q and DCR.
7 - 30 Hz constant acceleration of 1.5 Gs, 10 minutes
31 - 50 Hz constant displacement of 0.33 inches, 5 minutes
50 - 500 Hz constant acceleration of 1.2 Gs, 10 minutes
Mechanical Shock
After exposure part remains within
MGDQ1 Series - 500 Gs per axis, 2 directions
specified electrical parameters for
MGDQ2 Series - 500 Gs per axis, 2 directions
L, Q and DCR.
MGDQ3 Series - 500 Gs per axis, 2 directions
MGDQ4 Series - 500 Gs per axis, 2 directions
MGDQ5 Series - 500 Gs per axis, 2 directions
MGDQ6 Series - 500 Gs per axis, 2 directions
Solderability
Wetting shall cover 90% minimum of
each termination
Dip pads in RMA
flux, 63/37 solder
(Sn/Pb) at 232°C for
5 seconds ±2
seconds.
Component Adhesion
(Push Test)
Component shall withstand 6 lb. push
force minimum without delaminating
from mounting surface.
Apply and measure force with a digital force gauge set.
Resistance to Solvent Withstands 6 minutes of alcohol.
Withstands 3 minutes forced spray Freon TMS
Chemical
Ionic Contamination
Conductivity:
11 µOhms/cm maximum
pH:
5.5 to 9
Chlorides:
65 ppm maximum
Sodium:
20 ppm maximum
Potassium:
10 ppm maximum
Series
Revision
Subject parts to an environment of 85°C 85% R.H. for 168
hours. After exposure allow parts to dry for 4 hours before
measurements are taken.
Precondition at 25°C for 60 minutes. Expose parts to an
environment of +40°C with 90 to 95% R.H. for 240 hours.
MGDQ6A0For Print Distribution to Customers
Sheet 3 of 6
