CATALOG 128_CATALOG 128.qxd 4/25/2014 7:15 AM Page 76 PCB Accessories Tools & Handles Pad Cutters, Insertion Tools Hand Insertion Tools for Push-In Terminals Pad Cutters Part No Terminal P/N Holder Type A13 A13-1 P91A P156 P133A T44 T68 T28 T49 T46 series & K24 - K31 K36 T42-1 T42-1 Shank with removable rubber handle Shank with removable rubber handle Wooden Handle Wooden Handle Shank with removable rubber handle P134 P149A P149 Wooden Handle Wooden Handle Shank with removable rubber handle A13 Shank with removable rubber handle Pad Cutter Shank Type (A13 type) P149 Shank with removable rubber handle P149A - Wooden Handle Type Tools P138A Wooden Handle type Vector Pad Cutters provide an effective method for creating isolated solder pads around holes in copper clad boards. Pilot pin enters hole and rotates, creating a clearance area around the solder pad. Available for boards with.062" or .042" diameter holes. Also available without handles for use with manual or power drills. Part Holder No. Type P116C Handle/Shank P138A Handle/Shank P138C Shank Only A .055" .040" .040" B T107 Shows pad removal & pad cutter P116C Shank Only P138C C .188" .250" .086" .125" .086" .125" Bus Strips * * * * Flat cold-drawn flat copper wire, 0.017" thick (+/-0.003") 0.080"W with 0.042" diameter holes on 0.100" centers Hot 100% Tin dipped, fully RoHS compliant Compatible with most Vectorbord(R) hole patterns Shank Use with Vectorbord(R) .250" .125" .125" Pattern G, H .062" holes Pattern P, .042: holes Pattern P, .042: holes Part No. Pkg Qty T107/C T107/10 100 10 HA14 Pull Type Ejector Handle * Extraction/insertion handles * Mounts on front edge of Plugbordtm with single screw or roll-pin * Plastic (FE4) Part No. HA14 HA14/C Package Quantity 4 100 HA9 Rotation Type Ejector Handle Dimensional information for HA9 is on Page 44 * Card ejector, corner mounting * Supports up to 40 lbs extraction force * White nylon, (hardware included) 76 www.vectorelect.com Specification subject to change without notice 800-423-5659 Part No. HA9/4 HA9/C Pkg Qty 4 100 CATALOG 128_CATALOG 128.qxd 4/25/2014 7:17 AM Page 78 PCB Accessories Tefzel 28 AWG Wire Insulation Properties Property Test Method Thermal Properities Nominal Melting Point ASTM D3159 Flow Rate Upper Service Temperature ASTM D315 UL746 Mechanical Properities Tensile Strength, 23oC (73oF) Specific Gravity Ultimate Elongation, 23oC (73oF) Flexural Modulus, 23oC (73oF) Impact Streength, 23oC (73oF) Hardness, Durometer Compressive Strength Linear Coefficient of Expansion, ASTM D3159 ASTM D792 ASTM D3159 ASTM D790 ASTM D256 ASTM D2240 ASTM D695 ASTM E831 0-100oC (32-212oF) Unit oC (oF) g/10 min oC Tefzel Insulated Silver Plated Wire for use with No. 02 Bit 255-280 (491-536) 20 135 MPa, (psi) % MPa (psi) J/m (ft-lb/in.) Shore D MPa, (psi) mm/mm/oC in./in./oF Electrical Properities kV/mm (V/0.001in.) Dielectric Strength, 0.25mm (0.010in.) ASTM D149 Dielectric Constant, 1MHz,23oC (73oF) ASTM D1531 Dissipation Factor, 1MHz,23oC (73oF) ASTM D1531 Volume Resistivity ASTM D257 ohm.cm Arc Resistance ASTM D49 seconds General Properities Water Absorption, 24 h ASTM D570 Weather and Chemical Resistance Limiting Oxygen Index ASTM D2863 Slit-N-Wrap(R) Wire Value % Part No. AWG Color Spool Dia. 40, (6,500) 1.71 300 1,200 (170,000) No Break 63 38 (5,500) 12.6x 10-5 (7.0 x 10-5 ) W28-6A W28-6B W28-6D W28-6E W28-6F W28-6H W28-6AU W28-6BU W28-6DU W28-6EU W28-6FU W28-6HU 28 28 28 28 28 28 28 28 28 28 28 28 green red blue white yellow black green red blue white yellow black Feet/Spool Spools/Pkg 50 50 50 50 50 50 150 150 150 150 150 150 2 2 2 2 2 2 1 1 1 1 1 1 1" 1" 1" 1" 1" 1" 1.5" 1.5" 1.5" 1.5" 1.5" 1.5" See specifications on Page 81 70 (1,800) 2.5-2.6 0.00540 3 17 1 x 10 (1 x 10 ) 122 0.007 Excellent 30-32 % Accessories Vector 28AWG Tefzel wire is rated 300V at 150 degrees C T120-1 Slip-On Contacts * * * * Reels of slip-on contacts. 5" apart Slips onto .025" square posts 28 gage PVC insulated blue wire Temperature Range: -310 to 221oF (-190 to 105oC) EyeletsT15.23,T123 * 2 versions provide hole size reduction T123 - reduces .055" dia. holes to .042" * T123 eyelets are copper with .0003" to .0005" thick tin plating T15.23 - reduces .062" dia. holes to .042" * Simulates copper thru hole plating * Used to commit power and ground planes ID B .04 + .02 1.0 + 0.5 Contact No Contact Body Detail .060 REF 1.52 C Board Black Shrinkable Tubing Contact T123 Eyelet A T123 Eyelet No Contact End Terminal Only Contact Part No. Description Package Quantity. installed on wire installed on wire Reel of 50 Reel of 250 T120-1/50 T120-1/250 78 www.vectorelect.com Part No. Qty A B C ID T15.23/M T123/500 T123/1000 1000 500 1000 .062" .055" .055" .105" .105" .105" .093" .093" .093" .042" .042" .042" Specification subject to change without notice 800-423-5659 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vector: T107/C P116C P138A P138C A13 A13-1 P149A P149 P134 HA14 T107/10