PR29MF21NSZ Series PR39MF2xNSZ Series IT(rms)0.9A, Zero Cross type DIP 8pin Triac output SSR PR29MF21NSZ Series PR39MF2xNSZ Series Non-zero cross type is also available. (PR29MF1xNSZ Series/PR39MF1xNSZ Series) Description Agency approvals/Compliance PR29MF21NSZ Series and PR39MF2xNSZ Series Solid State Relays (SSR) are an integration of an infrared emitting diode (IRED), a Phototriac Detector and a main output Triac. These devices are ideally suited for controlling high voltage AC loads with solid state reliability while providing 4.0kV isolation (Viso(rms)) from input to output. 1. Recognized by UL508, file No. E94758 (as model No. R29MF2/R39MF2) 2. Approved by CSA 22.2 No.14, file No. LR63705 (as model No. R29MF2/R39MF2) 3. Optionary available VDE approved ()(DIN EN 60747-52), file No. 40008898 (only for PR39MF2xNSZ Series as model No. R39MF2) 4. Package resin : UL flammability grade (94V-0) () Features 1. Output current, IT(rms)0.9A 2. Zero crossing functionary (VOX : MAX. 35V) 3. 8 pin DIP package (SMT gullwing also available) 4. High repetitive peak off-state voltage (VDRM : 600V, PR39MF2xNSZ Series) (VDRM : 400V, PR29MF21NSZ Series) 5. I FT ranks available (see Model Line-up in this datasheet) 6. Superior noise immunity (dV/dt : MIN. 100V/s) 7. Response time, ton : MAX. 50s 8. Lead-free terminal components are also available (see Model Line-up section in this datasheet) 9. High isolation voltage between input and output (Viso(rms) : 4.0kV) DIN EN60747-5-2 : successor standard of DIN VDE0884. Up to Date code "RD" (December 2003), approval of DIN VDE0884. From Date code "S1" (January 2004), approval of DIN EN60747-5-2. Applications 1. Isolated interface between high voltage AC devices and lower voltage DC control circuitry. 2. Switching motors, fans, heaters, solenoids, and valves. 3. Power control in applications such as lighting and temperature control equipment. Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D4-A00701EN Date Mar. 31. 2004 (c) SHARP Corporation PR29MF21NSZ Series PR39MF2xNSZ Series Internal Connection Diagram 8 5 6 1 2 3 4 Cathode Anode Cathode Cathode 5 6 8 Gate Output (T1) Output (T2) Zero Crossing Circuit 1 2 3 4 Outline Dimensions (Unit : mm) 1.20.3 1.20.3 1.050.2 6 5 Model No. SHARP mark "S" R29MF2 Rank mark CSA mark 3 0.260.1 0.5TYP. 3.50.5 3.250.5 2.540.25 0.260.1 0.50.1 :0 to 13 5 R39MF2 1.20.3 SHARP mark "S" Rank mark 3 6 5 Model No. R39MF2 Rank mark 4 1 3 4 Date code (2 digit) Factory identification mark 7.620.3 0.260.1 0.5TYP. 3.50.5 9.660.5 Epoxy resin 2.540.25 0.260.1 0.50.1 Product mass : approx. 0.56g 2 Anode mark 7.620.3 9.660.5 3.250.5 8 1.050.2 CSA mark Date code (2 digit) Factory identification mark 2.540.25 1.0+0.4 -0 4. SMT Gullwing Lead-Form [ex. PR39MF21NIPF] Model No. CSA mark Epoxy resin Product mass : approx. 0.54g 6.50.5 6 1.0+0.4 -0 10.0+0 -0.5 1.050.2 8 7.620.3 Epoxy resin 3. Through-Hole [ex. PR39MF21NSZF] 1.20.3 4 Date code (2 digit) Factory identification mark 9.660.5 Anode mark 2 0.350.25 1 Anode mark 7.620.3 Product mass : approx. 0.56g 2 Rank mark 4 2.540.25 1 R29MF2 CSA mark Date code (2 digit) Factory identification mark 9.660.5 SHARP mark "S" Model No. :0 to 13 1.0+0.4 -0 Epoxy resin 0.350.25 3 5 3.50.5 2 6 6.50.5 1 Anode mark 8 1.050.2 3.50.5 8 6.50.5 SHARP mark "S" 2. SMT Gullwing Lead-Form [ex. PR29MF21NIPF] 6.50.5 1. Through-Hole [ex. PR29MF21NSZF] 1.0+0.4 -0 10.0+0 -0.5 Product mass : approx. 0.54g Sheet No.: D4-A00701EN 2 PR29MF21NSZ Series PR39MF2xNSZ Series Outline Dimensions (Unit : mm) 5. Through-Hole VDE option [ex. PR39MF21YSZF] Model No. 5 SHARP mark "S" R39MF2 4 2 3 4 Rank mark VDE identification mark 1 3 4 Date code (2 digit) Factory identification mark 7.620.3 0.5TYP. 3.50.5 9.660.5 Epoxy resin 2.540.25 0.260.1 0.50.1 Product mass : approx. 0.56g 2 Anode mark 7.62 9.66 Model No. CSA mark 0.3 0.5 3.250.5 R39MF2 VDE identification mark Date code (2 digit) Factory identification mark 2.540.25 5 0.260.1 1 6 4 Rank mark CSA mark Anode mark 8 :0 to 13 1.0+0.4 -0 Epoxy resin 0.350.25 6 1.050.2 6.50.5 8 6.50.5 SHARP mark "S" 1.20.3 1.050.2 3.50.5 1.20.3 6. SMT Gullwing Lead-Form VDE option [ex. PR39MF21YIPF] 1.0+0.4 -0 10.0+0 -0.5 Product mass : approx. 0.54g Sheet No.: D4-A00701EN 3 PR29MF21NSZ Series PR39MF2xNSZ Series Date code (2 digit) A.D. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 1st digit Year of production A.D Mark 2002 A 2003 B 2004 C 2005 D 2006 E 2007 F 2008 H 2009 J 2010 K 2011 L 2012 M ** N * 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D Mark P R S T U V W X A B C ** * repeats in a 20 year cycle Factory identification mark Factory identification Mark Country of origin no mark Japan * This factory marking is for identification purpose only. Please contact the local SHARP sales representative to see the actural status of the production. Rank mark Please refer to the Model Line-up table. Sheet No.: D4-A00701EN 4 PR29MF21NSZ Series PR39MF2xNSZ Series (Ta=25C) Parameter Symbol Rating Unit *3 Forward current IF 50 mA Input Reverse voltage VR 6 V RMS ON-state current IT (rms) 0.9 *3 A *4 Peak one cycle surge current Isurge 9 A Output Repetitive PR29MF21NSZ 400 VDRM V peak OFF-state voltage PR39MF2xNSZ 600 *1 Isolation voltage 4.0 Viso(rms) kV Operating temperature Topr -30 to +85 C Storage temperature C Tstg -40 to +125 *2 Soldering temperature C Tsol 270 *5 1mm Absolute Maximum Ratings Soldering area *1 40 to 60%RH, AC for 1minute, f=60Hz *2 For 10s *3 Refer to Fig.1, Fig.2 *4 f=50Hz sine wave *5 Lead solder plating models: 260C Electro-optical Characteristics Parameter Forward voltage Input Reverse current Repetitive peak OFF-state current ON-state voltage Holding current Output Critical rate of rise of OFF-state voltage Rank 1 Zero cross voltage Rank 2 Rank 1 Minimum trigger current Rank 2 Transfer charac- Isolation resistance teristics Rank 1 Turn-on time Rank 2 (Ta=25C) Symbol VF IR IDRM VT IH dV/dt Conditions IF=20mA VR=3V VD=VDRM IT=0.9A VD=6V - VD=1/2 *VDRM IF=15mA, Resistance load IF=10mA, Resistance load VOX IFT VD=6V, RL=100 RISO DC500V,40 to 60%RH IF=20mA, VD=6V, RL=100 IF=10mA, VD=6V, RL=100 ton MIN. - - - - - 100 TYP. 1.2 - - - - - MAX. 1.4 10 100 3.0 25 - Unit V A A V mA V/s - - 35 V - - 5x1010 - - 1011 10 5 - - - 50 mA s Sheet No.: D4-A00701EN 5 PR29MF21NSZ Series PR39MF2xNSZ Series Model Line-up (1) (Lead-free terminal components) Lead Form Shipping Package DIN EN60747-5-2 Model No. Through-Hole Sleeve 50pcs/sleeve - Approved SMT Gullwing Taping 1 000pcs/reel - VDRM [V] Rank mark IFT[mA] (VD=6V, RL=100) 1 2 1 MAX.10 MAX.5 MAX.10 Rank mark IFT[mA] (VD=6V, RL=100) 1 2 1 MAX.10 MAX.5 MAX.10 Approved PR39MF21NSZF PR39MF21YSZF PR39MF21NIPF PR39MF21YIPF PR39MF22NSZF PR39MF22YSZF PR39MF22NIPF PR39MF22YIPF PR29MF21NSZF PR29MF21NIPF - 600 400 Model Line-up (2) (Lead solder plating components) Lead Form Shipping Package DIN EN60747-5-2 Model No. Through-Hole Sleeve 50pcs/sleeve - Approved PR39MF21NSZ PR39MF21YSZ PR39MF22NSZ PR39MF22YSZ PR29MF21NSZ - SMT Gullwing Taping 1 000pcs/reel - Approved - - VDRM [V] 600 400 Please contact a local SHARP sales representative to see the actual status of the production. Sheet No.: D4-A00701EN 6 PR29MF21NSZ Series PR39MF2xNSZ Series Fig.2 RMS ON-state Current vs. Ambient Temperature Fig.1 Forward Current vs. Ambient Temperature 70 1 RMS ON-state current IT (rms) (A) Forward current IF (mA) 60 50 40 30 20 10 0 -30 0 50 0.8 0.6 0.4 0.2 0 -30 100 0 Ambient temperature Ta (C) Fig.3-b Forward Current vs. Forward Voltage (Rank 2) 0C 100 100 Ta=75C 50 Forward current IF (mA) Forward current IF (mA) Ta=75C -25C 50C 10 5 0.5 1 1.5 2 2.5 50 50C 25C 3 5 -25C 1 1.1 Fig.4-a Minimum Trigger Current vs. Ambient Temperature (Rank 1) Minimum trigger current IFT (mA) Minimum trigger current IFT (mA) 1.5 VD=6V RL=100 4 3 2 1 0 1.4 6 5 0 -30 1.3 Fig.4-b Minimum Trigger Current vs. Ambient Temperature (Rank 2) VD=6V RL=100 6 1.2 Forward voltage VF (V) Forward voltage VF (V) 7 0C 10 1 0.9 1 0 100 Ambient temperature Ta (C) Fig.3-a Forward Current vs. Forward Voltage (Rank 1) 25C 50 50 5 4 3 2 1 0 -30 100 Ambient temperature Ta (C) 0 50 100 Ambient temperature Ta (C) Sheet No.: D4-A00701EN 7 PR29MF21NSZ Series PR39MF2xNSZ Series Fig.5 ON-state Voltage vs. Ambient Temperature Fig.6 Relative Holding Current vs. Ambient Temperature 1.2 Relative holding current IH (tC) / IH (25C)x100% 1 000 IT=0.9A ON-state voltage VT (V) 1.1 1 0.9 0.8 0.7 0.6 -30 0 20 40 60 80 VD=6V 100 10 -30 100 Ambient temperature Ta (C) 40 60 80 100 Fig.8 ON-state Current vs. ON-state Voltage 1.5 Resistance load, IF=15mA : Rank 1 IF=10mA : Rank 2 IF=20mA Ta=25C 1.2 ON-state current IT (A) Zero-cross voltage VOX (V) 20 Ambient temperature Ta (C) Fig.7 Zero-cross Voltage vs. Ambient Temperature 15 0 10 5 0.9 0.6 0.3 0 -30 0 0 50 100 0 Ambient temperature Ta (C) 100 VD=6V RL=100 Ta=25C Turn-on time tON (s) Turn-on time tON (s) 1.5 Fig.9-b Turn-on Time vs. Forward Current (Rank 2) 10 1 10 1.0 ON-state voltage VT (V) Fig.9-a Turn-on Time vs. Forward Current (Rank 1) 100 0.5 VD=6V RL=100 Ta=25C 10 1 20 30 40 50 1 100 10 100 Forward current IF (mA) Forward current IF (mA) Remarks : Please be aware that all data in the graph are just for reference. Sheet No.: D4-A00701EN 8 PR29MF21NSZ Series PR39MF2xNSZ Series Design Considerations Recommended Operating Conditions Input Output Load supply current Frequency Operating temperature IOUT(rms) f Topr - MIN. 20 10 0 - - Conditions Parameter Symbol Input signal current Rank 1 IF(ON) at ON state Rank 2 Input signal current at OFF state IF(OFF) PR29MF21NSZ Load supply voltage VOUT(rms) PR39MF2xNSZ - Locate snubber circuit between output terminals - (Cs=0.022F, Rs=47) 50 - -20 - MAX. 25 15 0.1 120 240 Unit IT(rms)x80%() mA 60 80 Hz C mA mA V () See Fig.2 about derating curve (IT(rms) vs. ambient temperature). Design guide In order for the SSR to turn off, the triggering current (IF) must be 0.1mA or less. Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry. If the phase difference between the voltage and the current at the output pins is large enough, zero crossing type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should be used in combination with the above mentioned snubber circuit selection process. When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation, please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can merely recommend some circuit values to start with : Cs=0.022F and Rs=47. The operation of the SSR and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit component values accordingly. When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops in current are not accompanied by large instantaneous changes in voltage across the Triac. This fast change in voltage is brought about by the phase difference between current and voltage. Primarily, this is experienced in driving loads which are inductive such as motors and solenods. Following the procedure outlined above should provide sufficient results. For over voltage protection, a Varistor may be used. Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main output triac as possible. All pins shall be used by soldering on the board. (Socket and others shall not be used.) Degradation In general, the emission of the IRED used in SSR will degrade over time. In the case where long term operation and / or constant extreme temperature fluctuations will be applied to the devices, please allow for a worst case scenario of 50% degradation over 5years. Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least twice the minimum required triggering current from initial operation. Sheet No.: D4-A00701EN 9 PR29MF21NSZ Series PR39MF2xNSZ Series Recommended Foot Print (reference) SMT Gullwing Lead-form 1.7 2.54 2.54 2.54 8.2 2.2 (Unit : mm) Standard Circuit R1 +VCC 2 SSR D1 3 V1 Load 8 ZS AC Line 6 Tr1 ZS : Surge absorption circuit (Snubber circuit) For additional design assistance, please review our corresponding Optoelectronic Application Notes. Sheet No.: D4-A00701EN 10 PR29MF21NSZ Series PR39MF2xNSZ Series Manufacturing Guidelines Soldering Method Reflow Soldering: Reflow soldering should follow the temperature profile shown below. Soldering should not exceed the curve of temperature profile and time. Please don't solder more than twice. (C) 300 Terminal : 260C peak ( package surface : 250C peak) 200 Reflow 220C or more, 60s or less Preheat 150 to 180C, 120s or less 100 0 0 1 2 3 4 (min) Flow Soldering : Flow soldering should be completed below 270C and within 10s. Preheating is within the bounds of 100 to 150C and 30 to 80s. Please don't solder more than twice. Hand soldering Hand soldering should be completed within 3s when the point of solder iron is below 400C. Please don't solder more than twice. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. Sheet No.: D4-A00701EN 11 PR29MF21NSZ Series PR39MF2xNSZ Series Cleaning instructions Solvent cleaning : Solvent temperature should be 45C or below. Immersion time should be 3minutes or less. Ultrasonic cleaning : The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of PCB and mounting method of the device. Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. Recommended solvent materials : Ethyl alcohol, Methyl alcohol and Isopropyl alcohol. In case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. Sheet No.: D4-A00701EN 12 PR29MF21NSZ Series PR39MF2xNSZ Series Package specification Sleeve package Through-Hole Package materials Sleeve : HIPS (with anti-static material) Stopper : Styrene-Elastomer Package method MAX. 50pcs of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers. The product shall be arranged in the sleeve with its anode mark on the tabless stopper side. MAX. 20 sleeves in one case. Sleeve outline dimensions 12.0 2 5.8 10.8 520 6.7 (Unit : mm) Sheet No.: D4-A00701EN 13 PR29MF21NSZ Series PR39MF2xNSZ Series Tape and Reel package SMT Gullwing Package materials Carrier tape : A-PET (with anti-static material) Cover tape : PET (three layer system) Reel : PS Carrier tape structure and Dimensions F J D E G MA X. H H A B C I 5 K Dimensions List A B 16.00.3 7.50.1 H I 10.40.1 0.40.05 C 1.750.1 J 4.20.1 D 12.00.1 K 10.20.1 E 2.00.1 (Unit : mm) F G +0.1 4.00.1 1.5-0 Reel structure and Dimensions e d c g Dimensions List a b 330 17.51.5 e f 231.0 2.00.5 f a b (Unit : mm) c d 1.0 100 130.5 g 2.00.5 Direction of product insertion Pull-out direction [Packing : 1 000pcs/reel] Sheet No.: D4-A00701EN 14 PR29MF21NSZ Series PR39MF2xNSZ Series Important Notices with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). * The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. * Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. * If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. * Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection * This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. * Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Sheet No.: D4-A00701EN 15