REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE F8859. Add device Class V criteria. Add delta limits, table III. Add case outline X. Update boilerplate to MIL-PRF-38535 requirements. - lgt 01-05-10 Raymond Monnin B Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 09-08-12 Thomas M. Hess REV SHEET REV B B B B SHEET 15 16 17 18 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Monica L. Poelking STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil CHECKED BY Raymond Monnin APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A Michael A. Frye DRAWING APPROVAL DATE MICROCIRCUIT, DIGITAL, ADVANCED CMOS, SYNCHRONOUS PRESETTABLE BINARY COUNTER, MONOLITHIC SILICON 89-06-05 REVISION LEVEL B SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-89582 1 OF 18 5962-E310-09 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - Federal stock class designator \ RHA designator (see 1.2.1) 89582 01 E A Device type (see 1.2.2) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number For device class V: 5962 - Federal stock class designator \ RHA designator (see 1.2.1) 01 V X A Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) 89582 / \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AC163 Synchronous presettable binary counter 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device requirements documentation Device class M Q or V Vendor self-certification to the requirements for MIL-STD-883 compliant, nonJAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Certification and qualification to MIL-PRF-38535 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter E F 2 X Descriptive designator GDIP1-T16 or CDIP2-T16 GDFP2-F16 or CDFP3-F16 CQCC1-N20 CDFP4-F16 Terminals Package style 16 16 20 16 Dual-in-line Flat pack Square leadless chip carrier Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) .................................................................................. -0.5 V dc to +7.0 V dc DC input voltage range (VIN) ................................................................................ -0.5 V dc to VCC + 0.5 V dc DC output voltage range (VOUT) ........................................................................... -0.5 V dc to VCC + 0.5 V dc Clamp diode current (IIK, IOK) ............................................................................... 20 mA DC output current ................................................................................................ 50 mA DC VCC or GND current (per pin) ......................................................................... 50 mA Storage temperature range (TSTG) ....................................................................... -65C to +150C Maximum power dissipation (PD) ......................................................................... 500 mW Lead temperature (soldering, 10 seconds) .......................................................... +300C Thermal resistance, junction-to-case (JC) ........................................................... See MIL-STD-1835 Junction temperature (TJ) ................................................................................... +175C 4/ 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) .................................................................................. +2.0 V dc to +6.0 V dc Input voltage range (VIN) ...................................................................................... +0.0 V dc to VCC Output voltage range (VOUT)................................................................................. +0.0 V dc to VCC Case operating temperature range (TC) ............................................................... -55C to +125C Input rise or fall times (V/t): VCC = 3.6 V..................................................................................................... 0 to10 ns VCC = 5.5 V..................................................................................................... 0 to 8 ns ______ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of -55C to +125C. 4/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. 5/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data retention implies no input transition and no stored data loss with the following conditions: VIH 70% VCC, VIL 30% VCC, VOH 70% VCC @ -20A, VOL 30% VCC @ 20 A. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JEDEC Standard No. 20 - Standard for Description of 54/74ACXXXXX and 54/74ACTXXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http://www.jedec.org or from Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834). 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 4 3.2.5 Counting sequence. The counting sequence shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 40 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 5 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Positive input clamp voltage 3022 Negative input clamp voltage 3022 High level output voltage 3006 Symbol Device type and device class All V Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified VIC+ For input under test IIN = 1.0 mA VIC- For input under test IIN = -1.0 mA VIN = VIH minimum or VIL maximum IOH = -50 A VOH 4/ VIN = VIH minimum or VIL maximum IOH = -12 mA VIN = VIH minimum or VIL maximum IOH = -24 mA Low level output voltage 3007 VOL 4/ VIN = VIH minimum or VIL maximum IOH = -50 mA VIN = VIH minimum or VIL maximum IOL = 50 A VIN = VIH minimum or VIL maximum IOL = 12 mA VIN = VIH minimum or VIL maximum IOL = 24 mA VIN = VIH minimum or VIL maximum IOL = 50 mA High level input voltage Low level input voltage VIH 5/ VIL 5/ VCC Group A subgroups Limits 3/ Unit Min Max 0.0 V 1 0.4 1.5 V All V Open 1 -0.4 -1.5 V All All All All All All 3.0 V 1, 2, 3 2.9 All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All 3.0 V 4.5 V 4.4 5.5 V 5.4 5.5 V 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 3.0 V 1, 2, 3 4.5 V 5.5 V V 2.56 2.4 3.86 3.7 4.86 4.7 3.85 0.1 4.5 V 0.1 5.5 V 0.1 3.0 V 5.5 V 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 3.0 V 1, 2, 3 4.5 V 5.5 V 0.36 0.5 0.36 0.5 0.36 0.5 1.65 2.1 4.5 V 3.15 5.5 V 3.85 3.0 V 1, 2, 3 V V 0.9 4.5 V 1.35 5.5 V 1.65 V See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Input leakage current low 3009 Input leakage current high 3010 Quiescent supply current, output high 3005 Quiescent supply current, output low 3005 Input capacitance 3012 Power dissipation capacitance Functional tests 3014 Propagation delay time, high to low low to high, CP to Qn (Count mode) 3003 Symbol IIL IIH ICCH ICCL CIN CPD 6/ 7/ tPHL1 8/ Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified VIN = 0.0 V Device type and device class All All VIN = 5.5 V 8/ 5.5 V 5.5 V VIN = VCC or GND IO = 0 A All All 5.5 V VIN = VCC or GND IO = 0 A All All 5.5 V All All All All All All See 4.4.1c TC = +25C See 4.4.1c TC = +25C, f = 1 MHz See 4.4.1b VIN = VIH or VIL Verify output VOUT TC = +25C CL = 50 pF minimum RL = 500 See figure 5 All All All All All All All All All All All All All All All All TC = -55C and +125C CL = 50 pF minimum RL = 500 See figure 5 tPLH1 8/ Group A subgroups Limits 3/ Min All All tPLH1 8/ tPHL1 VCC Unit Max 1 -0.1 2, 3 -1.0 A A 1 0.1 2, 3 1.0 1 4 2, 3 80 1 4 2, 3 80 5.0 V 4 8.0 pF 5.0 V 4 60.0 pF 3.0 V 7, 8 L H 5.5 V 7, 8 L H 3.0 V 9 1.0 10.5 4.5 V 1.0 8.0 3.0 V 1.0 11.0 4.5 V 1.0 8.0 1.0 12.5 4.5 V 1.0 9.5 3.0 V 1.0 13.5 4.5 V 1.0 9.5 3.0 V 10, 11 A A ns ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Propagation delay time, high to low low to high, CP to Qn (Load mode) 3003 Symbol tPHL2 8/ Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified TC = +25C CL = 50 pF minimum RL = 500 See figure 5 Device type and device class All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All tPLH2 8/ tPHL2 8/ TC = -55C and +125C CL = 50 pF minimum RL = 500 See figure 5 tPLH2 8/ Propagation delay time, high to low low to high, CP to TC 3003 tPHL3 8/ TC = +25C CL = 50 pF minimum RL = 500 See figure 5 tPLH3 8/ tPHL3 8/ TC = -55C and +125C CL = 50 pF minimum RL = 500 See figure 5 tPLH3 8/ Propagation delay time, high to low low to high, CET to TC 3003 tPHL4 8/ TC = +25C CL = 50 pF minimum RL = 500 See figure 5 tPLH4 8/ tPHL4 8/ TC = -55C and +125C CL = 50 pF minimum RL = 500 See figure 5 tPLH4 8/ VCC Group A subgroups Limits 3/ Unit Min Max 1.0 9.5 4.5 V 1.0 7.0 3.0 V 1.0 10.5 4.5 V 1.0 7.5 1.0 12.0 4.5 V 1.0 8.5 3.0 V 1.0 12.5 4.5 V 1.0 9.0 1.0 12.5 4.5 V 1.0 10.0 3.0 V 1.0 13.5 4.5 V 1.0 9.5 1.0 15.0 4.5 V 1.0 11.0 3.0 V 1.0 16.5 4.5 V 1.0 11.0 1.0 10.5 4.5 V 1.0 7.5 3.0 V 1.0 9.0 4.5 V 1.0 6.0 1.0 12.0 4.5 V 1.0 9.0 3.0 V 1.0 11.0 4.5 V 1.0 7.5 3.0 V 3.0 V 9 10, 11 3.0 V 3.0 V 9 10, 11 3.0 V 3.0 V 9 10, 11 ns ns ns ns ns ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Set-up time, high or low, SR to CP 3003 Symbol tS1 8/ Hold time, high or low, SR to CP 3003 th1 Set-up time, high or low, Pn to CP 3003 tS2 8/ 8/ Hold time, high or low, Pn to CP 3003 th2 Set-up time, high or low, PE to CP 3003 tS3 Hold time, high or low, PE to CP 3003 Set-up time, high or low, CEP or CET to CP 3003 8/ 8/ th3 8/ tS4 8/ Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = -55C and +125C CL = 50 pF minimum RL = 500 See figure 5 Device type and device class All All All All All All All All All All TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = -55C and +125C CL = 50 pF minimum RL = 500 See figure 5 TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = +25C CL = 50 pF minimum RL = 500 See figure 5 VCC Group A subgroups Limits 3/ Min 3.0 V 9 4.5 V 3.0 V 10, 11 14.0 17.0 9 -1.0 10, 11 -0.5 All All All All All All All All All All All All 4.5 V 9, 10, 11 0.0 3.0 V 9 13.5 3.0 V 9 10, 11 -1.0 -0.5 All All All All All All All All All All All All All All All All All All All All All All All All All All 4.5 V 9, 10, 11 0.0 3.0 V 9 12.5 4.5 V 10, 11 ns 17.0 11.0 4.5 V ns ns 8.0 10, 11 4.5 V 16.0 9.5 3.0 V 9 4.5 V -1.5 ns -0.5 10, 11 4.5 V -0.5 0 3.0 V 9 4.5 V 3.0 V ns 8.5 4.5 V 3.0 V ns 12.0 3.0 V 3.0 V Max 9.5 4.5 V 3.0 V Unit 6.5 ns 4.5 10, 11 4.5 V 8.0 5.5 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 9 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Hold time, high or low, CEP or CET to CP 3003 th4 Clock pulse width, CP (Count mode) 3003 Clock pulse width, CP (Load mode) 3003 tw1 Maximum clock frequency, CP 3003 8/ 8/ tw2 8/ fmax 8/ Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V unless otherwise specified TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = +25C CL = 50 pF minimum RL = 500 See figure 5 TC = +25C CL = 50 pF minimum RL = 500 See figure 5 Device type and device class All All All All All All All All All All All All All All All All All All All All All All VCC Group A subgroups Limits 3/ Min 3.0 V 9, 10, 11 0 4.5 V 9 0 4.5 V 10, 11 0.5 3.0 V 9, 10, 11 5.0 4.5 V 9, 10, 11 5.0 3.0 V 9, 10, 11 5.0 4.5 V 9, 10, 11 5.0 3.0 V 9 70 4.5 V 3.0 V Unit Max ns ns ns MHz 95 10, 11 4.5 V 55 90 1/ For tests not listed in the referenced MIL-STD-883, [e.g. VIH, VIL], utilize the general test procedure under the conditions listed herein. 2/ Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table I herein. Output terminals not designated shall be high level logic, low level logic, or open, except as follows: a. VIC (pos) tests, the GND terminal can be open. TC = +25C. b. VIC (neg) tests, the VCC terminal shall be open. TC = +25C. c. All ICC tests, the output terminal shall be open. When performing these tests, the current meter shall be placed in the circuit such that all current flows through the meter. Additional detailed information on qualified devices (i.e. pin for pin conditions and testing sequence) is available from the qualifying activity (DSCC-VQC) upon request. 3/ For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and the direction of current flow, respectively; and the absolute value of the magnitude, not the sign, is relative to the minimum and maximum limits, as applicable, listed herein. All devices shall meet or exceed the limits specified in table I, as applicable, at 3.0 V VCC 3.6 V and 4.5 V VCC 5.5 V. 4/ The VOH and VOL tests shall be tested at VCC = 3.0 V and 4.5 V. The VOH and VOL tests are guaranteed, if not tested, for other values of VCC. Limits shown apply to operation at VCC = 3.3 V 0.3 V and VCC = 5.0 V 0.5 V. Tests with input current at +50 mA or -50 mA are performed on only one input at a time with duration not to exceed 10 ms. Transmission driving tests may be performed using VIN = VCC or GND. When VIN = VCC or GND is used, the test is guaranteed for VIN = VIH minimum and VIL maximum. 5/ The VIH and VIL tests are not required if applied as forcing functions for VOH and VOL tests. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 10 TABLE I. Electrical performance characteristics - Continued. 6/ Power dissipation capacitance (CPD) determines both the power consumption (PD) and dynamic current consumption (IS). Where: PD = (CPD + CL) (VCC x VCC)f + (ICC x VCC) IS = (CPD + CL) VCCf + ICC f is the frequency of the input signal and CL is the external output load capacitance. 7/ Tests shall be performed in sequence, attributes data only. Functional tests shall include the truth table and other logic patterns used for fault detection. The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2 herein. Functional tests shall be performed in sequence as approved by the qualifying activity on qualified devices. For VOUT measurements, L 0.3VCC and H 0.7VCC. 8/ For propagation delay tests, all paths must be tested. AC limits at VCC = 5.5 V are equal to the limits at VCC = 4.5 V and guaranteed by testing at VCC = 4.5 V. AC limits at VCC = 3.6 V are equal to limits at VCC = 3.0 V and guaranteed by testing at VCC = 3.0 V. Minimum ac limits for VCC = 5.5 V are 1.0 ns and guaranteed by guardbanding the VCC = 4.5 V minimum limits to 1.5 ns. Case outlines Terminal number 1 E, F, and X Terminal symbol 2 NC 2 SR CP 3 P0 SR CP 4 P1 P0 5 P2 P1 6 P3 NC 7 CEP P2 8 GND P3 9 PE CEP 10 CET GND 11 Q3 NC 12 Q2 PE 13 Q1 CET 14 Q0 Q3 15 TC Q2 16 VCC NC 17 ----- Q1 18 ----- Q0 19 ----- TC 20 ----- VCC NC = No connection FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 11 Inputs Action on the rising clock edge SR PE CET CEP L X X X Reset (clear) H L X X Load (Pn to Qn) H H H H Count (increment) H H L H H X No change (hold) L No change (hold) H = High voltage level L = Low voltage level X = Irrelevant FIGURE 2. Truth table. FIGURE 3. Logic diagram. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 12 Sequence illustrated in waveform: 1. Reset outputs to zero. 2. Preset to binary twelve. 3. Count to thirteen, fourteen, fifteen, zero, one, and two. 4. Inhibit. FIGURE 4. Counting sequence. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 13 FIGURE 5. Switching waveforms and test circuit. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 14 NOTES: 1. CL = 50 pF or equivalent (includes probe and jig capacitance). 2. RT should be equal to ZOUT of the pulse generator. 3. RL = 500 or equivalent. 4. Input signal from pulse generator: VIN = 0.0 V to VCC; PRR 1 MHz; ZO = 50; tr 3.0 ns; tf 3.0 ns; tr and tf shall be measured from 10% of VCC to 90% of VCC and from 90% of VCC to 10% of VCC, respectively; duty cycle = 50 percent. 5. Timing parameters shall be tested at a minimum input frequency of 1MHz. 6. The outputs are measured one at a time with one transition per measurement. FIGURE 5. Switching waveforms and test circuit - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 15 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. a. Tests shall be as specified in table II herein. b. For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table in figure 2 herein. The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2, herein. For device classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device. c. CIN and CPD shall be measured only for initial qualification and after process or design changes which may affect capacitance. CIN shall be measured between the designated terminal and GND at a frequency of 1 MHz. CPD shall be tested in accordance with the latest revision of JEDEC Standard No. 20 and table I herein. For CIN and CPD, test all applicable pins on five devices with zero failures. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 16 TABLE II. Electrical test requirements. Test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Subgroups (in accordance with MIL-PRF-38535, table III) Device class M Device class Q Device class V Interim electrical parameters (see 4.2) --- --- 1 Final electrical parameters (see 4.2) 1/ 1, 2, 3, 7, 8, 9 1/ 1, 2, 3, 7, 8, 9 2/, 3/ 1, 2, 3, 7, 8, 9 Group A test requirements (see 4.4) 1, 2, 3, 4, 7, 8, 9, 10, 11 1, 2, 3, 4, 7, 8, 9, 10, 11 1, 2, 3, 4, 7, 8, 9, 10, 11 Group C end-point electrical parameters (see 4.4) 1, 2, 3 1, 2, 3 3/ 1, 2, 3, 7, 8, 9, 10, 11 Group D end-point electrical parameters (see 4.4) 1, 2, 3 1, 2, 3 1, 2, 3 Group E end-point electrical parameters (see 4.4) 1, 7, 9 1, 7, 9 1, 7, 9 1/ PDA applies to subgroup 1. 2/ PDA applies to subgroups 1, 7 and deltas. 3/ Delta limits as specified in table III, shall be required where specified, and the delta limits shall be completed with reference to the zero hour electrical parameters. TABLE III. Burn-in and operating life test, delta parameters (+25C). Parameter Symbol Delta limits Quiescent current ICC 300 nA Input current low level IIL 20 nA Input current high level IIH 20 nA Output voltage low level VCC = 5.5 V IOL = 24 mA VOL 0.04 V Output voltage high level VCC = 5.5 V IOH = -24 mA VOH 0.2 V 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. b. TA = +125C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 17 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table II herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25C 5C, after exposure, to the subgroups specified in table II herein. 4.5 Methods of inspection. Methods of inspection shall be specified as follows: 4.5.1 Voltage and current. Unless otherwise specified, all voltages given are referenced to the microcircuit GND terminal. Currents given are conventional current and positive when flowing into the referenced terminal. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.4 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89582 A REVISION LEVEL B SHEET 18 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 09-08-12 Approved sources of supply for SMD 5962-89582 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8958201EA 0C7V7 54AC163DMQB 5962-8958201FA 0C7V7 54AC163FMQB 5962-89582012A 0C7V7 54AC163LMQB 5962-8958201XA 3/ 54AC163K02Q 5962-8958201VXA 3/ 54AC163K02V 5962-8958201XC 3/ 54AC163K01Q 5962-8958201VXC 3/ 54AC163K01V 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 0C7V7 Vendor name and address QP Semiconductor 2945 Oakmead Village Court Santa Clara, CA 95051 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.