本カタログに掲載の仕様は予告なく変更する場合があります。御注文及び御使用前に、納入仕様書などで内容を御確認下さい。
Specificationsgivenhereinmaybechangedatanytimewithoutpriornotice.Pleaseconfirmtechnicalspecificationsbeforeyouorderand/oruse. www.koanet.co.jp
■性能 Performance
■負荷軽減曲線 DeratingCurve
周囲温度70℃以上で使用される場合は、上図負荷軽減曲線に従って、定
格電力を軽減して御使用下さい。
Forresistorsoperatedatanambienttemperatureof70℃ orabove,apower
ratingshallbederatedinaccordancewiththeabovederatingcurve.
-60 -40 -20 0 20 40 60 80 100 120140 160
-55 70 155
100
80
60
40
20
0
周囲温度 Ambienttemperature(℃)
Percentratedpower
定格電力比(%)
試験項目 規格値 PerformanceRequirements 試験方法
TestItems ΔR±(%+0.05Ω) TestMethods
保証値 Limit 代表値 Typical
抵抗値 規定の許容差内 ―25℃
Resistance Withinspecifiedtolerance
抵抗温度係数 規定値内 ―室温/100℃ up
T.C.R. WithinspecifiedT.C.R. Roomtemperature+100℃
過負荷(短時間) 0.5 0.3 定格電圧 × 2.5倍又は最高過負荷電圧の低い方を 5秒印加
Overload(Shorttime) Ratedvoltage× 2.5orMax.overloadvol.,whicheverislower,for5s
はんだ耐熱性 0.75 0.5
Resistancetosolderingheat 260℃±5℃,10s±1s
端子強度
リード線の外れ、端子のユルミのないこと。
― Twist360°,5times
Terminalstrength
Nolead-comingoffandlooseterminals
温度急変 10.75−55℃(30min.)/+125℃(30min.)5cycles
Rapidchangeoftemperature
耐湿負荷 53 40℃±2℃,90%〜95%RH,1000h
Moistureresistance 1.5時間 ON/0.5時間 OFFの周期 1.5hON/0.5hOFFcycle
70℃での耐久性 32 70℃±2℃,1000h
Enduranceat70℃ 1.5時間 ON/0.5時間 OFFの周期 1.5hON/0.5hOFFcycle
■使用上の注意 PrecautionsforUse
●本製品及び実装したプリント基板にフラックス等によるイオン性不純物質が付着していると、耐湿性・耐腐食性等の点から好ましく
ありません。フラックス内には、塩素・酸等のイオン性物質が含まれている場合があります。これらのイオン性物質を除去するため
には洗浄を行って下さい。特に鉛フリーはんだを御使用の場合、濡れ性向上の為、イオン性物質を多く含有している場合があります。
RMA系のはんだ又はフラックスをご使用になるか、十分な洗浄を行って下さい。また、保管環境や実装条件・環境等によって、汗、
塩等のイオン性物質を付着させた場合も、耐湿性・耐腐食性等の点から好ましくありません。その汚染時に対しましてもこれらのイ
オン性物質を除去するために洗浄を行って下さい。
●外装塗装が難燃性特殊塗料の為、外部衝撃に比較的弱いので取り扱いにご注意下さい。洗浄は最小限にして下さい。洗浄直後は多少
塗装膜が弱くなりますので、十分に乾燥するまで塗装膜に外力を加えないで下さい。乾燥後、元の強度に戻りますので、洗浄後約20
分間は抵抗器の塗装膜に外力が加わらない様に配慮下さい。特に基板の積み重ね等は、行わないで下さい。
●Ionicimpuritiessuch asfluxetc.thatare attached totheseproducts or thosemountedonto a PCB,negativelyaffect their moisture
resistance,corrosionresistance,etc.Thefluxmaycontainionicsubstanceslikechlorine,acid,etc.Pleasewashthemtogetridofthese
ionicsubstancesespeciallywhenusinglead-freesolderthatmaycontainmuchofthesaidsubstancesforimprovingawetting
characteristic.UsingRMAsolderorRMAflux,orwell-washingisneeded.Also,attachingionicsubstancessuchasperspiration,saltetc.
bystorageenvironments or mountingconditions/environments negatively affectstheirmoisture resistance,corrosionresistance etc.
Pleasewashthemtoremovetheionicsubstanceswhentheyarepolluted.
●Becarefultohandletheseresistorsbecauseoutercoatingsarecomparativelyweaktooutershockduetoflameproofspecialcoats.Please
washthemtoaminimum.Noexternalforceisgiventothecoatingfilmsuntiltheyarewelldriedbecausethecoatingfilmsbecomeweaker
rightafterwashing.Theoriginalstrengthwillbereturnedaftertheyaredried,sopleasepayattentionnottoapplyanyexternalforceonto
thecoatingfilmofresistorsfor20minutesafterdrying.EspeciallynoPCboardsshallbepiledup.
小電力形抵抗器
LowPowerTypeResistors