Directory chapter 02 with 6 rows, 2.00 mm pitch Page 6-row - general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02.02 Technical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02.03 Straight male connectors with press-in termination . . . . . . . . . . . . . . . . . . . . . . 02.04 Angled female connectors with press-in termination . . . . . . . . . . . . . . . . . . . . . 02.08 Angled female connectors with solder (SMC) termination . . . . . . . . . . . . . . . . . 02.10 Compatibility with OBSAI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02.12 6-row 6-row 02 . 01 6-row General information 6-row General information In comparison to the standard 5-row har-bus(R) HM series, this new 6-row version offers a significantly higher contact density, thus permitting applications where very high contact density is important. Typically, for a signal transmission of 1.5 Gbps it is possible to obtain 7.5 differential pairs per cm of card edge (see figure 1). For a signal transmission of 2.5 Gbps at least 5 differential pairs per cm of card edge can be obtained (see figure 2). All male connectors can be supplied with end wall, coding pins and guiding system. End wall Guiding system Coding Pos. 1 Male and female connectors are both available with 72 or 144 contacts and can be supplied in reel or tube packaging. Female connectors with press-in termination The 6-row female connector needs comparable space on the daughter card as the 5-row versions, as it has similar outer dimensions. Compared to the male connectors, coding pins and a guiding system are available upon request too. Figure 1 Guiding system Coding Pos. 1 / Pos. 2 Flange Figure 2 Male connectors Each contact position can be loaded with any of the 13 different contacts lengths shown (see figure 3). Female connectors in SMC (Surface Mount Compatible) technology Using the reflow soldering process, these 6-row female connectors in SMC technology can be soldered to the PCB at the same time as other SMC components. So the handling cost can be reduced significantly and there is no need for a separate press-in process. These connectors are made from a high temperature plastic material that can withstand up to 260C (lead free soldering). To hold the connector securely on the PCB before the solder process, kinked contacts are offered as standard on both connector sides. Further SMC information see chapter 01. 02 . 02 Figure 3 6-row Technical characteristics : complementary to IEC 61 076-4-101 (2 mm hard metric specification) Number of contacts : 72 or 144 Contact spacing : 2.00 mm (1.50 mm between contact rows on the termination side of female connectors) Working current : 1.0 A (24 C temp. raise) 6-row Design 1.5 A (52 C temp. raise) 2.0 A (88 C temp. raise) Test voltage Ur.m.s. : min. 750 V Contact resistance : < 20 m Impedance (differential) : 100 Typical differential data rate : 1.5 - 2.5 Gbps Temperature range : - 55 C ... + 125 C during reflow soldering Performance level* max. 260 C (peak temperature) : performance level 2 = 250 mating cycles performance level 1 = 500 mating cycles Termination technique : press-in for male and female connectors SMC for female connectors, compatible with lead-free solder process Pcb characteristics : min. 1.4 mm for male and female connectors with press-in terminations 1.6 mm - 2.4 mm for female connectors with SMC terminations Recommended configuration of plated through holes : Mating force press-in SMC Plated hole-O 0.6 0.05 mm 0.7 + 0.07 - 0.05 mm Hole-O 0.7 0.02 mm 0.8 0.02 mm Cu 30 - 50 m 30 - 50 m Sn 5 - 15 m 5 - 15 m : < 0.75 N/pin Materials Mouldings : Thermoplastic resin, glass-fibre filled, UL 94-V0 Contacts : Copper alloy Contact surface : Au/Ni Packaging Tube : Male connectors and female connectors with press-in terminations Tape & Reel : Female connectors with SMC terminations * Other platings on request 02 . 03 6-row 6-row Male connectors straight, with press-in termination Identification Number Contact length [mm] of mating termination contacts side side Part number Contact configuration Connectors without flange without coding without endwall 72 8.2 3.7 17 41 072 1204 17 41 072 2204 144 8.2 3.7 17 44 144 1205 17 44 144 2205 72 8.2 3.7 17 42 072 1203 17 42 072 2203 144 8.2 3.7 17 45 144 1204 17 45 144 2204 Connectors without flange without coding with endwall 02 . 04 Connector dimensions see pages 02.06 and 02.07. The pin types A, B, C ... R, S, T can be mixed in any configuration. Please request the part number. Thin print part numbers: Bold print part numbers: performance level 1 performance level 2 6-row Identification Number Contact length [mm] mating termination of side side contacts Part number Connectors with flange without coding without endwall 72 8.2 3.7 17 43 072 1209 17 43 072 2209 144 8.2 3.7 17 46 144 1207 17 46 144 2207 6-row Male connectors straight, with press-in termination Contact configuration optional coding 2 optional coding 1 optional coding 2 optional coding 1 Connectors with flange with coding 1 without endwall 72 8.2 3.7 17 43 072 1211 17 43 072 2211 144 8.2 3.7 17 46 144 1209 17 46 144 2209 72 8.2 3.7 17 43 072 1210 17 43 072 2210 144 8.2 3.7 17 46 144 1208 17 46 144 2208 72 8.2 3.7 17 43 072 1212 17 43 072 2212 144 8.2 3.7 17 46 144 1210 17 46 144 2210 Connectors with flange with coding 2 without endwall Connectors with flange with coding 3 (= coding 1 + 2) without endwall Connector dimensions see pages 02.06 and 02.07. The pin types A, B, C ... R, S, T can be mixed in any configuration. Please request the part number. 02 . 05 Thin print part numbers: Bold print part numbers: performance level 1 performance level 2 6-row 6-row Male connectors straight, with press-in termination Drawing Dimensions in mm Connector dimensions [mm] x1 x2 x3 72 23.9 11 x 2 (= 22) 24.9 144 47.9 23 x 2 (= 46) 48.9 Row Position Row Row Position Row 02 . 06 Row Position Board drillings Board drillings All holes depth Datum plane without flange without coding with endwall depth Datum plane without flange without coding without endwall Contact positions Position Row All holes 6-row Dimensions in mm Drawing 6-row Male connectors straight, with press-in termination Connector dimensions [mm] Contact positions x2 x4 72 11 x 2 (= 22) 30.9 144 23 x 2 (= 46) 54.9 depth Datum plane with flange with coding without endwall Row optional coding 1 optional coding 2 Position Row Board drillings All holes Position Row 02 . 07 * Non-metallized drillings 6-row 6-row Female connectors angled, with press-in termination Identification Number Contact length [mm] of termination contacts side Part number Connectors without flange without coding 72 3.35 17 51 072 1102 17 51 072 2102 144 3.35 17 54 144 1102 17 54 144 2102 72 3.35 17 52 072 1105 17 52 072 2105 144 3.35 17 55 144 1105 17 55 144 2105 72 3.35 17 52 072 1106 17 52 072 2106 144 3.35 17 55 144 1106 17 55 144 2106 72 3.35 17 52 072 1107 17 52 072 2107 144 3.35 17 55 144 1107 17 55 144 2107 72 3.35 17 52 072 1108 17 52 072 2108 144 3.35 17 55 144 1108 17 55 144 2108 Connectors with flange without coding Connectors with flange with coding 1 Connectors with flange with coding 2 Connectors with flange with coding 3 (= coding 1 + 2) 02 . 08 Connector dimensions see page 02.09. Thin print part numbers: Bold print part numbers: performance level 1 performance level 2 6-row Drawing Dimensions in mm 6-row Female connectors angled, with press-in termination Connector dimensions [mm] without flange without coding with flange with coding Position Position Row Row Board drillings Position Contact positions x1 x2 x3 72 24.0 11 x 2 (= 22) 31.0 144 48.0 23 x 2 (= 46) 55.0 coding 1 coding 2 coding 3 Board drillings All holes Row no coding All holes Position Row 02 . 09 * Non-metallized drillings 6-row 6-row Female connectors angled, with solder (SMC) termination Identification Number Contact length [mm] of termination contacts side Part number Connectors without flange without coding 72 2.5 17 51 072 1802 17 51 072 2802 144 2.5 17 54 144 1802 17 54 144 2802 72 2.5 17 52 072 1805 17 52 072 2805 144 2.5 17 55 144 1805 17 55 144 2805 72 2.5 17 52 072 1806 17 52 072 2806 144 2.5 17 55 144 1806 17 55 144 2806 72 2.5 17 52 072 1807 17 52 072 2807 144 2.5 17 55 144 1807 17 55 144 2807 72 2.5 17 52 072 1808 17 52 072 2808 144 2.5 17 55 144 1808 17 55 144 2808 Connectors with flange without coding Connectors with flange with coding 1 Connectors with flange with coding 2 Connectors with flange with coding 3 (= coding 1 + 2) 02 . 10 Connector dimensions see page 02.11. Thin print part numbers: Bold print part numbers: performance level 1 performance level 2 6-row Drawing Dimensions in mm 6-row Female connectors angled, with solder (SMC) termination Connector dimensions [mm] without flange without coding with flange with coding Position Position Row Row kinked pins at both ends of the connector kinked pins at both ends of the connector Board drillings All holes Row * Non-metallized drillings Contact positions x1 x2 x3 72 24.0 11 x 2 (= 22) 31.0 144 48.0 23 x 2 (= 46) 55.0 no coding coding 1 coding 2 coding 3 Board drillings All holes Position Row Position 02 . 11 Compatibility with OBSAI HARTING is a supporter member of OBSAI since September 2003. 6-row The Open Base Station Architecture Initiative (OBSAI) has developed a comprehensive set of open specifications for key module interfaces within the base station architecture. This development will enable an open market of base station modules. The OBSAI architecture provides a clear split in functionality and detailed internal interface specifications. This allows companies to create modules that are truly compatible in all OBSAI compliant base stations. OBSAI provides the entry for a new, competitive market for functionally standardized modules. HARTING's har-bus (R) HM Signal and HM Power connectors meet OBSAI specifications and provide a reliable and cost effective solution for connecting plug-in units to the backplane. The connector solution available from HARTING technology group will offer full compatibility and intermateability with base station modules. HARTING's activities in the wireless market are in line with those of OBSAI. The OBSAI specifications allow HARTING the opportunity to support a large group of wireless base station manufacturers and module manufacturers with unified, state of art interconnection solutions. 02 . 12