Product Specification 108-78140 19MAY09 Rev. A8 SUPER SEAL SUPER SEAL CONNECTOR 21 THIS SPECIFICATION IS STRUCTURED AS FOLLOWS: ITEM PAGE 1. ....... SCOPE ................................................................ 2/41 2. ....... APPLIED STANDARD ........................................ 2/41 3. ....... PRODUCT TYPES............................................... 2/41 4. ..... MATERIAL........................................................... 3/41 5. ....... DIMENSION AND CONFIGURATION............. 3/41 6. ....... RATING ................................................................ 3/41 7. ....... MEASURING METHOD AND PERFORMANCE. ........ 4/4110/41 8. ....... TEST STRUCTURE AND SEQUENCE...... 11/4113/41 9. ....... TEST METHOD ............................................ 14/4119/41 10........ TEST CONDITION............................................. 19/41 11. ....... PACKAGING AND MARKING.......................... 19/41 213-8535 3-5-8 1 of Tyco Electronics AMP K.K. (3-5-8 Hisamoto Takatsu-ku Kawasaki, 213-8535) This document is subject to change. Call local AMP for the latest revision. (c) Copyright 2000 by Tyco Electronics AMP K.K. All rights reserved. * : Trademark 41 Product Specification 108-78140 1. SCOPE This specification applies to the SUPER SEAL Connector. 2. APPLIED STANDARD The following standards are applied as a part of this specification sheet. (1) JIS (Japanese Industrial Standards) JIS D0203: Wet-Proof & Water-Proof Test Method Automobile Parts JIS Z8901: Dusts and Aerosols for Industrial Testing (2) MIL (Military Specifications and Standards) MIL 202: Test Method for Electronic and Electronical Parts (3) Qualitification Test Report: 501-78143 3. PRODUCT TYPES Structure No. of Pos. 60(34+26) Horizontal Type Cap Housing Connector Cap Housing assy Horizontal Type 34 Vertical Type Rev. A8 Part Number 1437288-3 6437288-3 1437288-5 6437288-5 3-1437285-2 3-6437285-2 1473427-1 6473427-1 1437288-1 6437288-1 1437288-2 6437288-2 2-1437285-5 2-6437285-5 2-1437285-6 2-6437285-6 3-1437285-0 3-6437285-0 3-1437285-1 3-6437285-1 1747359-1 1747359-2 2-1447232-3 2-6447232-3 2-1447232-4 2-6447232-4 Old Part No. 3900134-6011 3900135-6011 3900136-6011 3900134-3411 3900134-3412 3900135-3411 3900135-3412 3900136-3411 3900136-3412 3900279-3411 3900279-3412 2 of 41 Product Specification Structure No. of Pos. Horizontal Type Cap Housing Connector Cap Housing Assy 26 Vertical Type Receptacle contact assy 34 Plug Housing Connector Plug Housing assy 26 Hole Plug Rev. A8 108-78140 Part Number 9-1437287-8 9-6437287-8 9-1437287-9 9-6437287-9 5-144223-0 5-644223-0 1437288-4 6437288-4 2-1437285-8 2-6437285-8 2-1437285-9 2-6437285-9 1473423-1 6473423-1 1473423-2 6473423-2 1437288-6 1473418-1 6473418-1 1473418-2 6473418-2 3-1447221-3 3-1447221-4 Old Part No. 3900134-2611 3900134-2612 3900135-2611 3900135-2612 3900136-2611 3900136-2612 3900168-26 3900187-01 3900187-02 4-1437290-0 4-1437290-1 2-1437285-3 3-1437290-9 3-1437290-7 3-1437290-8 2-1437285-2 1-1447232-7 1473416-1 1473416-2 4-1437284-3 3900113-3421 3900113-3422 3900113-3411 3900113-3412 3900113-2621 3900113-2622 3900113-2611 3900113-2612 3400130 3 of 41 Product Specification 108-78140 4. MATERIAL Per the drawings. 5. DIMENSION AND CONFIGURATION Per the drawings. 6. RATING Item Rating & Condition Current Refer to the table below Voltage 250V (AC,DC) Temperature -40+125 Wire Conductor 0.51.25 Insulation Cover 1.62.2 Connector Allowable Current (Allowable maximum temperature in the vicinity of the contacting point is 150) (A) Ambient Temperature 60 80 100 125 All positions active 7 6 5 3 Only single position active 15 13 11 6 Measurement Set-up (Wire Size 0.85 min.) Rev. A8 () 4 of 41 Product Specification 108-78140 7. MEASUREMENT METHOD AND PERFORMANCE No. ITEM MEASUREMENT METHOD PERFORMANCE 7.1 External Appearance Visual and touch feeling inspection. 7.2 Feeling on Mating /Unmating Feeling is verified by mating and unmating the contact,housing and There should be no detrimental binding. connector 7.3 Insertion Force Pin contact or cap housing connector is fastened first,then Contact receptacle contact or plug housing and plug connector are mated Housing Connector at a constant mating speed of approx. 100mm/min. or less toward the axis. 4.9N(0.5kgf) or less 58.8N(6kgf) or less 98N(10kgf) or less 7.4 Withdrawal Force Pin contact or cap housing connector is fastened first,then mated Contact receptacle contact or plug housing and the connector is pulled at Housing a constant speed of approx. Connector 100mm/min. or less toward the axis. (Plug housing should be installed without locking.) 4.9N(0.5kgf) or less 58.8N(6kgf) or less 98N(10kgf) or less Rev. A8 There shall be no detrimental crack,rust,play, scratch,deformation and etc. 5 of 41 Product Specification No. 7.5 ITEM Voltage Drop 108-78140 MEASUREMENT METHOD PERFORMANCE As shown in Fig.1 while feeding open voltage of 205mV and short Initial: 5m or less circuit current of 100.5mA to the mated conector, measurement is After Durability Test: 10m or less taken at the point 75mm apart from the crimped barrel when temperature of the mated contact has saturated and then voltage drop by the wire is subtracted.(Resistance of wire is per Table 1.) Fig.1 measurement A 75 Table 1 Rev. A8 Wire size Resistance (m/75mm) 0.5 2.45 0.85 1.56 1.25 1.07 6 of 41 Product Specification No. 7.6 ITEM Insulation Resistance 108-78140 MEASUREMENT METHOD PERFORMANCE As shown in Fig.2 the connector is mated and insulation resistances between 100M or more neighboring contacts and between contact and earth are measured with insulation resistance meter of DC 500V. Fig. 2 Resistance Meter Between Contacts Wrap-up with Metal Foil Resistance Meter Between Contact and Earth 7.7 Rev. A8 Dielectric Withstanding Voltage As shown in Fig.2 while the connector is mated, 1000VAC or 1600V DC voltage Insulation breakdown does not develop. of commercial power frequency is applied of duration of 1 minute between contacts and between contact and earth. 7 of 41 Product Specification No. 7.8 ITEM Leak curent 108-78140 MEASUREMENT METHOD PERFORMANCE Peak value of leak curent and integrated quantity are measured while Peak Value: 100A or less DC 28 volt is applied with the circuit shown in Fig.3. The wire used for testing should be minimum size. Fig. 3 Rev. A8 8 of 41 Product Specification No. ITEM 7.9 Contact Solderability 7.10 Contact Insertion Characteristic (Between Contact and Housing) Contact Withdrawal Characteristic (Between Contact and Housing) Contact Retention Force (Between Contact and Housing) Strength of Crimp Connection (Between Contact and Wire) Housing Retention Force (Housing Locking Strength) 7.11 7.12 7.13 7.14 Rev. A8 108-78140 MEASUREMENT METHOD Solder bathSn-40Pb Matte Tin plating only Solder Temperature2355 Solder bathSn-3Ag-0.5Cu Immersion Duration50.5sec. Solder Temperature2505 FluxAlpha100 Immersion Duration50.5sec. AMP Spec. 109-5203 FluxULF-300R Contact crimped on free-length of wire is inserted into the proper location of the plug housing. Holding position of the wire is 20mm apart from the crimp barrel. Insertion speed is 100mm/min. or less. Withdraw the contact inserted under the condition of 6.10. PERFORMANCE Wet Solder Coverage (Plated area only) 95% Min. Contact can be inserted without bending of wire. There shall be no detrimental binding, crack and deformation. About 100mm long wire is crimped with the plug housing connector and the receptacle 58.8N(6kgf) or more contact is fastened and then the load that causes separation of contact from the housing with the wire pulled toward the axis at a constant speed of approx.100mm/min. is measured. After the receptacle contact with wire crimped is fastened and then the load that Wire size causes wire breakage or separation of the wire from the crimped barrel with the 0.5 wire pulled toward the axis at a constant speed of approx. 100mm/min. is measured. 0.85 1.25 88.2N (9kgf) or more 127.4N(13kgf) or more 176.4N(18kgf) or more After the cap housing is fastened, mated plug housing is pulled at a constant The lock mechanism shall not get released speed of approx. 100mm/min. or broken less than 98N(10kgf). 9 of 41 Product Specification No. 7.15 ITEM Seal Ability MEASUREMENT METHOD 108-78140 PERFORMANCE Seal Ability is measured with compressed air fed into the Initial: water-proof section of the connector. Before runnig the test, the tip of the wire is soldered and then sealed with adhesives. (Fig.4) After Durability Test: Measurement is taken with 9800Pa(gage)(0.1kg/c)compressed air fed into the connector submerged for duration of 30 seconds. If the air does not leak for 30 seconds, the pressure is raised each tine by an increment of 9800Pa(gage)(0.1kg/c). 98kPa(gage) (1kg/cm2)or more 48kPa(gage) (0.5kg/cm2)or more Fig.4 Adhesive Lead Soldering Rev. A8 10 of 41 Product Specification No. 7.16 ITEM Temperature Rise Magnitude 7.17 Intermittent Discontinuity MEASUREMENT METHOD 108-78140 PERFORMANCE "Temperature Rise Test" of item No.8.16 is made and temperature of Temperature rise: 60 or less. connector surface near the mated interface of the contact, is measured when the temperature has saturated. Power of 12V or less open voltage and 1A or less short circuit Intermittent discontinuity shall not last for 10 current is applied to the mated connector with the contacts in all sec or more. positions connected in series and then intermittent discontinuity is monitored with an intermittent discontinuity detector.(Fig.5) Fig. 5 Connector Rev. A8 Intermittent Discontinuity Checker 11 of 41 Product Specification 108-78140 8. TEST STRUCTURE AND SEQUENCE 8.1 Characteristic Test The test is made basically in line with the sequence shown in the Table 3. Table 3 Test Sample Sequence Contact Housing Connector 1 External Appearance External Appearance External Appearance Contact 2 Insertion Force Insertion Force Insertion Characteristic Withdrawal Force Withdrawal Force Feeling of Feeling of mating/unmating mating/unmating Housing Contact Force Retention Force Insertion Force 3 4 5 6 7 8 Rev. A8 Withdrawal Force Feeling of mating/unmating Contact Withdrawal Characteristic Contact Retention Force Contact Solderability 12 of 41 Product Specification 8.2 108-78140 Durability Test The test is made basically according to the Table 4. Table 4 Sequence Group Designation A B C D E F G H Rev. A8 BEFORE TEST TEST TEST TEST "Kojiri" durability Vibration Current cycle Low level voltage and Low level voltage and Intermittent Low level voltage and current resistance current resistance discontinuity current resistance External Appearance External Appearance External Appearance Low level voltage and current resistance "Kojiri"durability Temperature rise Low level voltage and Low level voltage and Temperature rise current resistance current resistance Low level voltage and External Appearance current resistance High temperature Low temperature exposure exposure Insertion force Low level voltage and Low level voltage and Low level voltage and current resistance Current resistance current resistance Seal ability Seal ability Seal ability Withdrawal force Withdrawal force Withdrawal force Insertion force Insertion force Thermal shock Water-Proof Insertion force Low level voltage and Leak current Low level voltage and current resistance Low level voltage and current resistance Seal ability current resistance Seal ability Withdrawal force Seal ability Withdrawal force Insertion force Withdrawal force Insertion force Over-current External appearance External appearance "Kojiri"durability Dust-proof Oil-proof, Solvent-proof Insertion force Low level voltage and Low level voltage and Low level voltage and Low level voltage and current resistance current resistance current resistance current resistance External appearance Insulation resistance Insulation resistance Withdrawal force Withdrawal force Insertion force External appearance Freezing Corrosion gas Ozone deterioration Low level voltage and Leak current Low level voltage and Low level voltage and current resistance current resistance current resistance Insulation resistance Seal ability Insulation resistance Seal ability Seal ability External appearance Salt Spray Low level voltage and Leak current current resistance Low level voltage and current resistance 13 of 41 Product Specification 108-78140 Sequence Group Designation BEFORE TEST TEST I insertion force Low level voltage and current resistance Insulation resistance Withstanding voltage Withdrawal force Weather-proof Low level voltage and current resistance Insulation resistance Withstanding voltage Withdrawal force Insertion force J External appearance TEST TEST High pressure cleaning Leak current External appearance Note: This measurement item is continually measured thru the test. Remark : 1. The test subject and item to be measure are shown above and below the dotted line respectively in the Table 4. 2. The measurement items shall be measured one after another sequentially in each item. Rev. A8 14 of 41 Product Specification 108-78140 9. TEST METHOD 9.1 "Kojiri"*(Rocking motion) Durability Test After the cap housing connector is fastened, the plug housing is mated in the regular manner and then 78.4N (8kgf) force is applied to-and-fro twice as shown in Fig.6. This test is repeated with the connector half if pulled from other half with slide distance stepped up by an increment of 1mm each time until the connector is fully unmated. These test procedure is defined as one cycle and is repeated 25 cycles. Test with the force applied towards right and left, is also made in the same manner. (Test with the force applied towards combined direction of to/fro and right/left is also acceptable.) Fig. 6 Fixed Location where "Kojiri" load is applied 78.4N 78.4N 5mm or less 9.2 High Temperature Exposure Test The connector is kept in a thermostatic chamber for 1000 hours and then taken out to be exposed to the normal temperature until it cools off to the temperature. The chamber temperature is set at 125. 9.3 Low Temperature Exposure Test The same test procedure as above is made except that the exposure time is 150 hours and the chamber temperature is set at -40. 9.4 Thermal Shock Test The connector is placed in a thermostatic chamber and given with 200cycles of heating/cooling process in the heating/cooling pattern shown below and then is taken out of the chamber to be left in the normal temperature for more than 2hours. Fig.7 One Hour High Temperature 1 Cycle For 5min.or less Normal Temperature Low Temperature One Hour Termostatic chamber temperature is set at 125 as the high temperature and -40 as the low temperature Rev. A8 15 of 41 Product Specification 9.5 108-78140 Salt Spray Test The connector is hung in a sealed tank and sprayed with mist of salt water for 96hours and then hung in a humidity chamber to be left in there for 96hours. The salt water(355 temperature, 51% saltdensity, 1.02681.0413 specific gravity, PH 6.5 7.2) is sprayed at pressure of 68.6 176.5KPa(gage) (0.7 1.8kg/c ). The humidity chamber is set at temperature of 805 and relative humidity of 9095%. Measurement is taken after the connector has dried up in normal temperature. During the salt water spray, 28 volt is applied across each contact of the connector to monitor leak current as shown in Fig.3. 9.6 Oil-Proof, Solvent-Proof Test The connector is dipped in various oil. Oil temperature is set at 502. Test is made in the sequence shown below. Torq.Con.Oil Dipping for 1hourDipping in kerosene for 5min. (Castle Auto Fluid Special) Transmission Oil(SAE 90) Dipping for 1hourDipping in kerosene for 5min. Engine Oil(SAE 10W-30) Dipping for 1hourDipping in kerosene for 5min. Clutch oil Dipping for 1hourDipping in kerosene for 5min. (Toyota Standard SHD) Brake Oil Dipping for 1hourDipping in kerosene for 5min. (Toyota Standard SHF) Another dipping test is also made on other sample in the following sequence with oil temperature set at 502. Washer liquid (available in the market) Dipping for 1hour Rinsing and dipping with or in tap water for 5min. Antifreezing solution (Castle Long Life Coolant) Dipping for 1hour Rinsing and dipping with/or in tap water 5min. Drying while left in room temperature Rev. A8 16 of 41 Product Specification 9.7 108-78140 Water-Proof Test The connector is placed in the thermostatic chamber, heated up 40min. and then immediately sprayed with water of normal temp. for 20min. in an water-proof test chamber. This is defined as 1cycle. The cycle is repeated 48 times for the test. The spray is made according to S2 of JIS D0203. Potential of 28 volt is applied across each contact of the connector during the water spray by the circuit shown in the Fig.3 and leak current is monitored. At running the test, the leading end of the lead wire shall be pulled out from the test chamber after having been soldered and then sealed with adhesives. The thermostatic chamber is set at 125. 9.8 Freezing Test The conector is put in a thermostatic chamber set at -305 immediately after dipped in boiling water for 1hour and then taken out of the chamber after the water stuck on the connector has freezed. Potential of 28 volts is applied across each contact of the conector during the test with the circuit shown in Fig.3, and leak current is monitored. 9.9 Corrosion Gas Test The connector is left in the test chamber for 24hours. The chamber is fed with 10ppmSO2 gas with 90% or more humidity and set at normal temperature. 9.10 Ozone Deterioration Test The connector is left in the test chamber for 24hours. The chamber is fed with 505ppm ozone gas and set at 40. Rev. A8 17 of 41 Product Specification 108-78140 9.11 Vibration Test at High Temperature The connector is fastened to vibration stand and vibrated on each of the 3mutually perpendicular axis (X, Y, Z) in 125 atmosphere. Other condition of the vibration is set by the Table 5. During the test, electrical current is turned on as shown in Fig. 8 and intermittent discontinuity is monitored. CABLE MOUNT Fig.8 CABLE MOUNT Mounting Jig 5 140 0 5 140 0 5 140 0 SHAKER SHAKER SHAKER CABLE MOUNT 5 CABLE LENGTH 150 0 mm Table 5 Acceleration (m/s2) 98245 (1025G) Vibration Duration (h) 3 hours per direction, Total of 9 hours Vibration Frequency (Hz) 50100 ... 98m/s2(10G)constant 100250 ... Half vibration stroke of 0.2mm constant 245m/s2(25G)constant Sweep Time 3min.(Log Sweep) 100176250Hz Half vibration stroke constant (0.2mm) Acceleration constant (25G) 9.12 Weather-Proof Test The connector is left in sunny outdoors for 12 months. Rev. A8 18 of 41 Product Specification 108-78140 9.13 Current Cycle Test Contacts of signal positions of the connector are turned on with the current of 3 Ampere, and power positions with the currnt of 4 Ampere. Turning on current for45 min. and then turning off for 15 min. are defined here as one cycle of test. The connector is tested with 200 cycles. Contacts of signal positions of the connector are turned on with the current of 3 Ampere and power positions with the current of 8 Ampere shown in fig. 9 at 120 atmosphere. This test cycle is repeated 50 times with vibration applied in draft free chamber according to the condition specified in the Table 5. The connector is vibrated perpendicular to the terminal axis. Fig. 9 12V 9.14 Over-current Test While the connector is held horizontally in a draft free chamber, current is turned on thru one circuit arbitrarily chosen. Current magnitude and time length for the over-current test are selected per the Table 6. Table 6 Wire Size 0.5 0.85 1.25 Rev. A8 Test Current Conduction Value (A) Time (min.) 30 40 5 50 Test Current Conduction Value (A) Time (s) 80 110 5 170 9.15 Dust-Proof Test Hang the mated connector in the chamber of 9001200mm each sides. Jet 10 seconds the 1.5Kg of powder specified by JIS Z8901-6 in every 15 minutes. This test cycle is repeated 8 cycles. Unmated and mate the connector in every 2 cyles. 9.16 Temperature Rise Test Conduct the current of 15 Ampere on an optional contact of the connector, then conduct the current of 6 Ampere on all of the contact. Measurement is based on per temperature rise magnitude 6.16. 19 of 41 Product Specification 108-78140 9.17 High-Pressure Cleaning Test Water-Jet Pressure: 80Kgf/c Water Quantity: 600l/hr Distance between Water-Nozzle and connector: 300mm Water-Jet Direction: Fig. 10 Test Cycle: Keep connector at 100 atomosphere Water-jet cleaning 30 sec. Natural cooling 1 minute Repeat 10 cycles Fig. 10 60 60 Sealing Fixed 10. TEST CONDITION (1) Contact and housing to be tested are to be selected randomly. (2) Contact and housing to be tested are to be crimped with wire of the maximum size except when otherwise noted. Wire length shall be decided each time. (3) Wire used in the tests should have enough performance of Heatstability and Solvent-resistance. (4) Test is to be made in the normal temperature and humidity except when otherwise noted. (5) Test is to be made with the connector mated except when otherwise noted. (6) Tolerance of the test conditions is 10% except when otherwise noted. (7) Quantity of test sample will be adjusted depending on situation. (8) Measurement for each test is to be made on 2 positions or more. 11. PACKAGING AND MARKING Packaging units will each contain suitable quantities of the product. Arrangements for transport and storage shall be such that no loss or damage is suffered. The following labeling will be displayed. Rev. A8 Product description or Cat. No. Quantity contained Manufacturer's name or abbreviated name Date of manufacture or Lot. No. 20 of 41 Product Specification 108-78140 Rev. A8 1. 22/41 2. 22/41 3. 22/41 4. 24/41 5. 24/41 6. 24/41 7. 25/4131/41 8. 32/4134/41 9. 35/4141/41 10. 41/41 11. 41/41 21 of 41 Product Specification 108-78140 1. SUPER SEAL 2. (1) JIS (Japanese Industrial Standards: ) JIS D0203: JIS Z8901: (2) MIL (Military Specifications and Standards) MIL 202: Test Method for Electronic and Electronical Parts (3) : 501-78143 3. 60(3426) 34 Rev. A8 1437288-3 6437288-3 1437288-5 6437288-5 3-1437285-2 3-6437285-2 1473427-1 6473427-1 1437288-1 6437288-1 1437288-2 6437288-2 2-1437285-5 2-6437285-5 2-1437285-6 2-6437285-6 3-1437285-0 3-6437285-0 3-1437285-1 3-6437285-1 1747359-1 1747359-2 2-1447232-3 2-6447232-3 2-1447232-4 2-6447232-4 3900134-6011 3900135-6011 3900136-6011 3900134-3411 3900134-3412 3900135-3411 3900135-3412 3900136-3411 3900136-3412 3900279-3411 3900279-3412 22 of 41 Product Specification 26 26 Rev. A8 9-1437287-8 9-6437287-8 9-1437287-9 9-6437287-9 5-1447223-0 5-6447223-0 1437288-4 6437288-4 2-1437285-8 2-6437285-8 2-1437285-9 2-6437285-9 1473423-1 6473423-1 1473423-2 6473423-2 1437288-6 1473418-1 6473418-1 1473418-2 6473418-2 3-1447221-3 3-1447221-4 3900134-2611 3900134-2612 3900135-2611 3900135-2612 3900136-2611 3900136-2612 3900168-26 3900187-01 3900187-02 34 108-78140 4-1437290-0 4-1437290-1 2-1437285-3 3-1437290-9 3-1437290-7 3-1437290-8 2-1437285-2 1-1447232-7 1473416-1 1473416-2 4-1437284-3 3900113-3421 3900113-3422 3900113-3411 3900113-3412 3900113-2621 3900113-2622 3900113-2611 3900113-2612 3400130 23 of 41 Product Specification 108-78140 4. 5. 6. 250VACDC 40125 0.51.25mm2 1.62.2 : 150 (A) () 60 80 100 125 Rev. A8 7 6 5 3 0.85 15 13 11 6 24 of 41 Product Specification 108-78140 7. 7.1 7.2 7.3 100mm/min. 4.9N(0.5kgf) 58.8N(6kgf) 98N(10kgf) 7.4 100mm/min. ( 4.9N(0.5kgf) 58.8N(6kgf) 98N(10kgf) Rev. A8 25 of 41 Product Specification 7.5 1 205mV 100.5mA 75mm 1 1 108-78140 5m 10m A A 75 1 (m/75mm) Rev. A8 0.5 2.45 0.85 1.56 1.25 1.07 26 of 41 Product Specification 7.6 108-78140 2 100M DC500V 2 7.7 Rev. A8 2 1000V 1600V 1 27 of 41 Product Specification 7.8 108-78140 3DC28V 100A 3 Rev. A8 28 of 41 Product Specification 7.9 108-78140 Sn-40Pb 2355 Sn-3Ag-0.5Cu () 50.5 2505 95% 100 50.5 AMP109-5203 ULF-300R 7.10 ( ) 20mm 100mm/min. 7.11 ( ) 7.10 7.12 ( ) 100mm 58.8N(6kgf) 100mm/min. 7.13 ( ) 100mm 100mm/min. 0.5 0.85 1.25 Rev. A8 88.2N (9kgf) 127.4N (13kgf) 176.4N (18kgf) 29 of 41 Product Specification 108-78140 7.14 ( ) 98N(10kgf) 100mm/min. 7.15 4 2 9.8KPa(gage)(0.1kg/cm )30 309.8KPa(gage)(0.1kg/cm2) 98KPa(gage) (1kg/cm2) 49KPa(gage) (0.5kg/cm2) 4 Rev. A8 30 of 41 Product Specification 108-78140 7.16 60 7.17 12V 10sec 1A 5 5 Rev. A8 31 of 41 Product Specification 108-78140 8. 8.1 3 3 Rev. A8 1 2 3 4 5 6 7 8 32 of 41 Product Specification 108-78140 8.2 4 4 A B C D E G H F Rev. A8 33 of 41 Product Specification 108-78140 I J : 1. 2. Rev. A8 34 of 41 Product Specification 108-78140 9. .1 678.4N(8kgf) 21mm1 25 6 78.4N 78.4N 5mm 9.2 1000 125 9.3 150 40 Rev. A8 35 of 41 Product Specification 108-78140 9.4 71 2002 7 1 1 5 1 12540 9.5 35551%1.0268 1.0413PH6.57.268.6176.5KPa(gage)(0.71.8kg/cm2 9680590 95%RH96 3 28V Rev. A8 36 of 41 Product Specification 108-78140 9.6 502 ( 1 5 SAE 90 1 5 SAE 10W-30 1 5 SHD 1 5 SHF 1 5 502 1 5 5 1 9.7 40 20 148JIS D0203S2 328V 125 9.8 1001305 3 28V Rev. A8 37 of 41 Product Specification 108-78140 9.9 SO210ppm90% 24 9.10 505pphm4024 9.11 8125 XYZ 35 5 8 5 5 140 0 140 0 5 140 0 5 150 0 mm 5 m/s2 98245 1025G h 3 9 Hz 50 100 ... 98m/s2(10G) 100 250 ... 0.2mm245m/s2(25G) 3Log Sweep 100176250Hz 0.2mm Rev. A8 25G 38 of 41 Product Specification 108-78140 9.12 12 9.13 3A 4A45 151200 120 3A 8A9 150 5 9 12V 9.14 1 6 6 Rev. A8 (A) 0.5 30 0.85 40 1.25 50 (min.) (A) (sec.) 80 5 110 5 170 39 of 41 Product Specification 108-78140 9.15 9001200mmJIS Z 8906 6 1.5kg1510 18 21 9.16 15A16A 7.16 9.17 100107 1110 1060 A: B: AB 10 60 60 328V Rev. A8 40 of 41 Product Specification 108-78140 7 784.532N/cm2 600l/h 300mm 30 sec 10. (1) (2) (3) (4) (5) (6) 10% (7) (8) 2 11. 1 Rev. A8 No. No. 41 of 41