Integrated Silicon Solution, Inc. — 1-800-379-4774
1
Rev. M
01/10/2010
Copyright © 2006 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability
arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any
published information and before placing orders for products.
IS61VPS25672A IS61LPS25672A
IS61VPS51236A IS61LPS51236A
IS61VPS102418A IS61LPS102418A
FEATURES
• Internal self-timed write cycle
• Individual Byte Write Control and Global Write
• Clock controlled, registered address, data and
control
• Burst sequence control using MODE input
• Three chip enable option for simple depth
expansion and address pipelining
• Common data inputs and data outputs
• Auto Power-down during deselect
• Single cycle deselect
• Snooze MODE for reduced-power standby
• JTAG Boundary Scan for PBGA package
• Power Supply
LPS: VDD 3.3V + 5%, VDDQ 3.3V/2.5V + 5%
VPS: VDD 2.5V + 5%, VDDQ 2.5V + 5%
• JEDEC 100-Pin TQFP, 119-ball PBGA, 165-ball
PBGA, and 209-ball (x72) packages
• Lead-free available
DESCRIPTION
The ISSI IS61LPS/VPS51236A, IS61LPS/VPS102418A,
and IS61LPS/VPS25672A are high-speed, low-power syn-
chronous static
RAMs
designed to provide burstable,
high-
performance
memory for communication and networking
applications. The IS61LPS/VPS51236A is organized as
524,288 words by 36 bits, the IS61LPS/VPS102418A is
organized as 1,048,576 words by 18 bits, and the IS61LPS/
VPS25672A is organized as 262,144 words by 72 bits.
Fabricated with ISSI's advanced CMOS technology, the
device integrates a 2-bit burst counter, high-speed SRAM
core, and high-drive capability outputs into a single mono-
lithic circuit. All synchronous inputs pass through regis-
ters controlled by a positive-edge-triggered single clock
input.
Write cycles are internally self-timed and are initiated by
the rising edge of the clock input. Write cycles can be one
to four bytes wide as controlled by the write control inputs.
Separate byte enables allow individual bytes to be written.
The byte write operation is performed by using the byte
write enable (BWE) input combined with one or more
individual byte write signals (BWx). In addition, Global
Write (GW) is available for writing all bytes at one time,
regardless of the byte write controls.
Bursts can be initiated with either ADSP (Address Status
Processor) or ADSC (Address Status Cache Controller)
input pins. Subsequent burst addresses can be generated
internally and controlled by the ADV (burst address
advance) input pin.
The mode pin is used to select the burst sequence order,
Linear burst is achieved when this pin is tied LOW.
Interleave burst is achieved when this pin is tied HIGH or
left floating.
256K x 72, 512K x 36, 1024K x 18
18Mb SYNCHRONOUS PIPELINED,
SINGLE CYCLE DESELECT STATIC RAM JANUARY 2010
FAST ACCESS TIME
Symbol Parameter 250 200 Units
tKQ Clock Access Time 2.6 3.1 ns
tKC Cycle Time 4 5 ns
Frequency 250 200 MHz
2
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
BLOCK DIAGRAM
19/20
BINARY
COUNTER
GW
CLR
CE
CLK Q0
Q1
MODE
A0'
A0
A1
A1'
CLK
ADV
ADSC
ADSP
17/18 19/20
ADDRESS
REGISTER
CE
D
CLK
Q
DQ(a-h)
BYTE WRITE
REGISTERS
D
CLK
Q
ENABLE
REGISTER
CE
D
CLK
Q
ENABLE
DELAY
REGISTER
D
CLK
Q
BWE
BW(a-h)
x18: a,b
x36: a-d
x72: a-h
CE
CE2
CE2
256Kx72;
512Kx36;
1024Kx18
MEMORY ARRAY
36,
or 18
or 72
INPUT
REGISTERS
CLK
OUTPUT
REGISTERS
CLK
OE
2/4/8
OE
DQa - DQd
36,
or 18
or 72
36,
or 18
or 72
A
POWER
DOWN
ZZ
Integrated Silicon Solution, Inc. — 1-800-379-4774
3
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
BOTTOM VIEW
BOTTOM VIEW
165-PIN BGA
165-Ball, 13x15 mm BGA
1mm Ball Pitch, 11x15 Ball Array
119-PIN BGA
119-Ball, 14x22 mm BGA
1mm Ball Pitch, 7x17 Ball Array
BOTTOM VIEW
209-BALL BGA
209-Ball, 14 mm x 22 mm BGA
1 mm Ball Pitch, 11 x 19 Ball Array
4
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
PIN CONFIGURATION — 256K X 72, 209-Ball PBGA (TOP VIEW)
1234567891011
ADQg DQg A CE2 ADSP ADSC ADV CE2 A DQb DQb
BDQg DQg BWcBWgNCBWE ABWbBWf DQb DQb
CDQg DQg BWhBWdNC CE NC BWeBWa DQb DQb
DDQg DQg VSS NC NC OE GW NC VSS DQb DQb
EDQPg DQPc VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQPf DQPb
FDQc DQc VSS VSS VSS NC VSS VSS VSS DQf DQf
GDQc DQc VDDQ VDDQ VDD NC VDD VDDQ VDDQ DQf DQf
HDQc DQc VSS VSS VSS NC VSS VSS VSS DQf DQf
JDQc DQc VDDQ VDDQ VDD NC VDD VDDQ VDDQ DQf DQf
KNC NC CLK NC VSS NC VSS NC NC NC NC
LDQh DQh VDDQ VDDQ VDD NC VDD VDDQ VDDQ DQa DQa
MDQh DQh VSS VSS VSS NC VSS VSS VSS DQa DQa
NDQh DQh VDDQ VDDQ VDD NC VDD VDDQ VDDQ DQa DQa
PDQh DQh VSS VSS VSS ZZ VSS VSS VSS DQa DQa
RDQPd DQPh VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQPa DQPe
TDQd DQd VSS NC NC MODE NC NC VSS DQe DQe
UDQd DQd NC A A A A A NC DQe DQe
VDQd DQd A A A A1 A A A DQe DQe
WDQd DQd TMS TDI A A0 A TDO TCK DQe DQe
11 x 19 Ball BGA—14 x 22 mm2 Body—1 mm Ball Pitch
PIN DESCRIPTIONS
Symbol Pin Name
A Address Inputs
A0, A1 Synchronous Burst Address Inputs
ADV Synchronous Burst Address
Advance
ADSP Address Status Processor
ADSC Address Status Controller
GW Global Write Enable
CLK Synchronous Clock
CE, CE2, CE2 Synchronous Chip Select
BWx (x=a,b,c,d Synchronous Byte Write
e,f,g,h) Controls
Symbol Pin Name
BWE Byte Write Enable
OE Output Enable
ZZ Power Sleep Mode
MODE Burst Sequence Selection
TCK, TDO JTAG Pins
TMS, TDI
NC No Connect
DQx Data Inputs/Outputs
DQPx Data Inputs/Outputs
VDD 3.3V/2.5V Power Supply
VDDQ Isolated Output Power Supply
3.3V/2.5V
Vss Ground
Integrated Silicon Solution, Inc. — 1-800-379-4774
5
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
119 BGA PACKAGE PIN CONFIGURATION-512K X 36 (TOP VIEW)
PIN DESCRIPTIONS
123456 7
AVDDQ AAADSP AAVDDQ
BNC A A ADSC A A NC
CNC A A VDD A A NC
DDQc DQPc Vss NC Vss DQPb DQb
EDQc DQc Vss CE Vss DQb DQb
FVDDQ DQc Vss OE Vss DQb VDDQ
GDQc DQc BWc ADV BWb DQb DQb
HDQc DQc Vss GW Vss DQb DQb
JVDDQ VDD NC VDD NC VDD VDDQ
KDQd DQd Vss CLK Vss DQa DQa
LDQd DQd BWd NC BWa DQa DQa
MVDDQ DQd Vss BWE Vss DQa VDDQ
NDQd DQd Vss A1* Vss DQa DQa
PDQd DQPd Vss A0* Vss DQPa DQa
RNC A MODE VDD NC A NC
TNC NC A A A NC ZZ
UVDDQ TMS TDI TCK TDO NC VDDQ
Symbol Pin Name
A Address Inputs
A0, A1 Synchronous Burst Address Inputs
ADV Synchronous Burst Address
Advance
ADSP Address Status Processor
ADSC Address Status Controller
GW Global Write Enable
CLK Synchronous Clock
CE Synchronous Chip Select
BWx (x=a-d) Synchronous Byte Write Controls
BWE Byte Write Enable
Symbol Pin Name
OE Output Enable
ZZ Power Sleep Mode
MODE Burst Sequence Selection
TCK, TDO JTAG Pins
TMS, TDI
NC No Connect
DQa-DQd Data Inputs/Outputs
DQPa-Pd Output Power Supply
VDD Power Supply
VDDQ Output Power Supply
Vss Ground
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired.
6
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
119 BGA PACKAGE PIN CONFIGURATION
1MX18 (TOP VIEW)
PIN DESCRIPTIONS
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired.
123456 7
AVDDQ AAADSP AA VDDQ
BNC A A ADSC A A NC
CNC A A VDD A A NC
DDQb NC Vss NC Vss DQPa NC
ENC DQb Vss CE Vss NC DQa
FVDDQ NC Vss OE Vss DQa VDDQ
GNC DQb BWb ADV Vss NC DQa
HDQb NC Vss GW Vss DQa NC
JVDDQ VDD NC VDD NC VDD VDDQ
KNC DQb Vss CLK Vss NC DQa
LDQb NC V s s NC BWa DQa NC
MVDDQ DQb Vss BWE Vss NC VDDQ
NDQb NC Vss A1* Vss DQa NC
PNC DQPb Vss A0* Vss NC DQa
RNC A MODE VDD NC A NC
TNC A A NC A A ZZ
UVDDQ TMS TDI TCK TDO NC VDDQ
Symbol Pin Name
A Address Inputs
A0, A1 Synchronous Burst Address Inputs
ADV Synchronous Burst Address
Advance
ADSP Address Status Processor
ADSC Address Status Controller
GW Global Write Enable
CLK Synchronous Clock
CE Synchronous Chip Select
BWx (x=a,b) Synchronous Byte Write Controls
BWE Byte Write Enable
Symbol Pin Name
OE Output Enable
ZZ Power Sleep Mode
MODE Burst Sequence Selection
TCK, TDO JTAG Pins
TMS, TDI
NC No Connect
DQa-DQb Data Inputs/Outputs
DQPa-Pb Output Power Supply
VDD Power Supply
VDDQ Output Power Supply
Vss Ground
Integrated Silicon Solution, Inc. — 1-800-379-4774
7
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
PIN DESCRIPTIONS
165 PBGA PACKAGE PIN CONFIGURATION
512K X 36 (TOP VIEW)
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired.
1234567891011
ANC A CE BWc BWb CE2 BWE ADSC ADV ANC
BNC A CE2 BWd BWa CLK GW OE ADSP ANC
CDQPc NC VDDQ Vss Vss Vss Vss Vss VDDQ NC DQPb
DDQc DQc VDDQ VDD Vss Vss Vss VDD VDDQ DQb DQb
EDQc DQc VDDQ VDD Vss Vss Vss VDD VDDQ DQb DQb
FDQc DQc VDDQ VDD Vss Vss Vss VDD VDDQ DQb DQb
GDQc DQc VDDQ VDD Vss Vss Vss VDD VDDQ DQb DQb
HNC Vss NC VDD Vss Vss Vss VDD NC NC ZZ
JDQd DQd VDDQ VDD Vss Vss Vss VDD VDDQ DQa DQa
KDQd DQd VDDQ VDD Vss Vss Vss VDD VDDQ DQa DQa
LDQd DQd VDDQ VDD Vss Vss Vss VDD VDDQ DQa DQa
MDQd DQd VDDQ VDD Vss Vss Vss VDD VDDQ DQa DQa
NDQPd NC VDDQ Vss NC A Vss Vss VDDQ NC DQPa
PNC NC A A TDI A1*TDOAAAA
RMODE NC A A TMS A0*TCKAAAA
Symbol Pin Name
A Address Inputs
A0, A1 Synchronous Burst Address Inputs
ADV Synchronous Burst Address
Advance
ADSP Address Status Processor
ADSC Address Status Controller
GW Global Write Enable
CLK Synchronous Clock
CE, CE2, CE2 Synchronous Chip Select
BWx (x=a,b,c,d) Synchronous Byte Write
Controls
Symbol Pin Name
BWE Byte Write Enable
OE Output Enable
ZZ Power Sleep Mode
MODE Burst Sequence Selection
TCK, TDO JTAG Pins
TMS, TDI
NC No Connect
DQx Data Inputs/Outputs
DQPx Data Inputs/Outputs
VDD 3.3V/2.5V Power Supply
VDDQ Isolated Output Power Supply
3.3V/2.5V
Vss Ground
8
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired.
165 PBGA PACKAGE PIN CONFIGURATION
1M X 18 (TOP VIEW)
PIN DESCRIPTIONS
1234567891011
ANC A CE BWb NC CE2 BWE ADSC ADV AA
BNC A CE2 NC BWa CLK GW OE ADSP ANC
CNC NC VDDQ Vss Vss Vss Vss Vss VDDQ NC DQPa
DNC DQb VDDQ VDD Vss Vss Vss VDD VDDQ NC DQa
ENC DQb VDDQ VDD Vss Vss Vss VDD VDDQ NC DQa
FNC DQb VDDQ VDD Vss Vss Vss VDD VDDQ NC DQa
GNC DQb VDDQ VDD Vss Vss Vss VDD VDDQ NC DQa
HNC Vss NC VDD Vss Vss Vss VDD NC NC ZZ
JDQb NC VDDQ VDD Vss Vss Vss VDD VDDQ DQa NC
KDQb NC VDDQ VDD Vss Vss Vss VDD VDDQ DQa NC
LDQb NC VDDQ VDD Vss Vss Vss VDD VDDQ DQa NC
MDQb NC VDDQ VDD Vss Vss Vss VDD VDDQ DQa NC
NDQPb NC VDDQ Vss NC A Vss Vss VDDQ NC NC
PNC NC A A TDI A1* TDO A A A A
RMODE NC A A TMS A0* TCK A A A A
Symbol Pin Name
A Address Inputs
A0, A1 Synchronous Burst Address Inputs
ADV Synchronous Burst Address
Advance
ADSP Address Status Processor
ADSC Address Status Controller
GW Global Write Enable
CLK Synchronous Clock
CE, CE2, CE2 Synchronous Chip Select
BWx (x=a,b) Synchronous Byte Write
Controls
Symbol Pin Name
BWE Byte Write Enable
OE Output Enable
ZZ Power Sleep Mode
MODE Burst Sequence Selection
TCK, TDO JTAG Pins
TMS, TDI
NC No Connect
DQx Data Inputs/Outputs
DQPx Data Inputs/Outputs
VDD 3.3V/2.5V Power Supply
VDDQ Isolated Output Power Supply
3.3V/2.5V
Vss Ground
Integrated Silicon Solution, Inc. — 1-800-379-4774
9
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
DQPb
DQb
DQb
VDDQ
VSS
DQb
DQb
DQb
DQb
VSS
VDDQ
DQb
DQb
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
DQa
DQa
VSS
VDDQ
DQa
DQa
DQPa
A
A
CE
CE2
BWd
BWc
BWb
BWa
CE2
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
DQPc
DQc
DQc
VDDQ
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
DQc
DQc
NC
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
A
A
A
A
A
A
A
A
A
46 47 48 49 50
PIN DESCRIPTIONS
A0, A1 Synchronous Address Inputs. These
pins must tied to the two LSBs of the
address bus.
A Synchronous Address Inputs
ADSC
Synchronous Controller Address
Status
ADSP
Synchronous Processor Address
Status
ADV
Synchronous Burst Address Advance
BWa-BWd Synchronous Byte Write Enable
BWE Synchronous Byte Write Enable
CE, CE2, CE2 Synchronous Chip Enable
CLK Synchronous Clock
DQa-DQd Synchronous Data Input/Output
DQPa-DQPd Parity Data Input/Output
GW Synchronous Global Write Enable
MODE Burst Sequence Mode Selection
OE Output Enable
VDD 3.3V/2.5V Power Supply
VDDQ Isolated Output Buffer Supply:
3.3V/2.5V
Vss Ground
ZZ Snooze Enable
PIN CONFIGURATION
512K x 36
100-PIN TQFP
10
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
PIN CONFIGURATION
1024K x 18
PIN DESCRIPTIONS
A0, A1 Synchronous Address Inputs. These
pins must tied to the two LSBs of the
address bus.
A Synchronous Address Inputs
ADSC
Synchronous Controller Address Status
ADSP
Synchronous Processor Address Status
ADV
Synchronous Burst Address Advance
BWa-BWb Synchronous Byte Write Enable
BWE Synchronous Byte Write Enable
CE, CE2, CE2 Synchronous Chip Enable
CLK Synchronous Clock
DQa-DQb Synchronous Data Input/Output
DQPa-DQPb Parity Data I/O; DQPa is parity for
DQa1-8; DQPb is parity for DQb1-8
GW Synchronous Global Write Enable
MODE Burst Sequence Mode Selection
OE Output Enable
VDD 3.3V/2.5V Power Supply
VDDQ Isolated Output Buffer Supply:
3.3V/2.5V
Vss Ground
ZZ Snooze Enable
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
A
A
CE
CE2
NC
NC
BWb
BWa
CE2
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
NC
NC
NC
VDDQ
VSS
NC
NC
DQb
DQb
VSS
VDDQ
DQb
DQb
NC
VDD
NC
VSS
DQb
DQb
VDDQ
VSS
DQb
DQb
DQPb
NC
VSS
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
A
A
A
A
A
A
A
A
A
46 47 48 49 50
100-PIN TQFP
Integrated Silicon Solution, Inc. — 1-800-379-4774
11
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
TRUTH TABLE(1-8) (3CE option)
OPERATION ADDRESS CECE
CECE
CE CE2CE2
CE2CE2
CE2 CE2 ZZ ADSPADSP
ADSPADSP
ADSP ADSCADSC
ADSCADSC
ADSC ADVADV
ADVADV
ADV WRITEWRITE
WRITEWRITE
WRITE OEOE
OEOE
OE CLK DQ
Deselect Cycle, Power-Down None H X X L X L X X X L-H High-Z
Deselect Cycle, Power-Down None L X L L L XXXXL-HHigh-Z
Deselect Cycle, Power-Down None L H X L L XXXXL-HHigh-Z
Deselect Cycle, Power-Down None L X L L H L X X X L-H High-Z
Deselect Cycle, Power-Down None L H X L H L X X X L-H High-Z
Snooze Mode, Power-Down None X X X H XXXXXX High-Z
Read Cycle, Begin Burst External L L H L L X X X L L-H Q
Read Cycle, Begin Burst External L L H L L X X X H L-H High-Z
Write Cycle, Begin Burst External L L H L H L X L X L-H D
Read Cycle, Begin Burst External L L H L H L X H L L-H Q
Read Cycle, Begin Burst External L L H L H L X H H L-H High-Z
Read Cycle, Continue Burst Next X X X L H H L H L L-H Q
Read Cycle, Continue Burst Next X X X L H H L H H L-H High-Z
Read Cycle, Continue Burst Next H X X L X H L H L L-H Q
Read Cycle, Continue Burst Next H X X L X H L H H L-H High-Z
Write Cycle, Continue Burst Next X X X L H H L L X L-H D
Write Cycle, Continue Burst Next H X X L X H L L X L-H D
Read Cycle, Suspend Burst Current X X X L HHHHLL-H Q
Read Cycle, Suspend Burst Current X X X L HHHHHL-HHigh-Z
Read Cycle, Suspend Burst Current H X X L X H H H L L-H Q
Read Cycle, Suspend Burst Current H X X L X HHHHL-HHigh-Z
Write Cycle, Suspend Burst Current X X X L H H H L X L-H D
Write Cycle, Suspend Burst Current H X X L X H H L X L-H D
NOTE:
1. X means “Don’t Care.” H means logic HIGH. L means logic LOW.
2. For WRITE, L means one or more byte write enable signals (BWa-h) and BWE are LOW or GW is LOW. WRITE = H for all
BWx, BWE, GW HIGH.
3. BWa enables WRITEs to DQa’s and DQPa. BWb enables WRITEs to DQb’s and DQPb. BWc enables WRITEs to DQc’s and
DQPc. BWd enables WRITEs to DQd’s and DQPd. BWe enables WRITEs to DQe’s and DQPe. BWf enables WRITEs to DQf’s
and DQPf. BWg enables WRITEs to DQg’s and DQPg. BWh enables WRITEs to DQh’s and DQPh. DQPa-DQPh are avail-
able on the x72 version. DQPa and DQPb are available on the x18 version. DQPa-DQPd are available on the x36 version.
4. All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
5. Wait states are inserted by suspending burst.
6. For a WRITE operation following a READ operation, OE must be HIGH before the input data setup time and held HIGH during the
input data hold time.
7. This device contains circuitry that will ensure the outputs will be in High-Z during power-up.
8. ADSP LOW always initiates an internal READ at the L-H edge of CLK. A WRITE is performed by setting one or more byte write
enable signals and BWE LOW or GW LOW for the subsequent L-H edge of CLK. See WRITE timing diagram for clarification.
12
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
PARTIAL TRUTH TABLE
Function GWGW
GWGW
GW BWEBWE
BWEBWE
BWE BWaBWa
BWaBWa
BWa BWbBWb
BWbBWb
BWb BWcBWc
BWcBWc
BWc BWdBWd
BWdBWd
BWd BWeBWe
BWeBWe
BWe BWfBWf
BWfBWf
BWf BWgBWg
BWgBWg
BWg BWhBWh
BWhBWh
BWh
Read H H X X X X X X X X
Read H L H H H H H H H H
Write Byte 1 H L L H H H H H H H
Write All Bytes H L L L L L L L L L
Write All Bytes L X X X X X X X X X
TRUTH TABLE(1-8) (1CE option)
NEXT CYCLE ADDRESS CECE
CECE
CE ADSPADSP
ADSPADSP
ADSP ADSCADSC
ADSCADSC
ADSC ADVADV
ADVADV
ADV
WRITEWRITE
WRITEWRITE
WRITE
OEOE
OEOE
OE DQ
Deselected None H X L X X X High-Z
Read, Begin Burst External L L X X X L Q
Read, Begin Burst External L L X X X H High-Z
Write, Begin Burst External L H L X L X D
Read, Begin Burst External L H L X H L Q
Read, Begin Burst External L H L X H H High-Z
Read, Continue Burst Next X H H L H L Q
Read, Continue Burst Next X H H L H H High-Z
Read, Continue Burst Next H X H L H L Q
Read, Continue Burst Next H X H L H H High-Z
Write, Continue Burst Next X H H L L X D
Write, Continue Burst Next H X H L L X D
Read, Suspend Burst Current X H H H H L Q
Read, Suspend Burst Current X H H H H H High-Z
Read, Suspend Burst Current H X H H H L Q
Read, Suspend Burst Current H X H H H H High-Z
Write, Suspend Burst Current X H H H L X D
Write, Suspend Burst Current H X H H L X D
NOTE:
1. X means “Don’t Care.” H means logic HIGH. L means logic LOW.
2. For WRITE, L means one or more byte write enable signals (BWa-h) and BWE are LOW or GW is LOW. WRITE = H for all
BWx, BWE, GW HIGH.
3. BWa enables WRITEs to DQa’s and DQPa. BWb enables WRITEs to DQb’s and DQPb. BWc enables WRITEs to DQc’s and
DQPc. BWd enables WRITEs to DQd’s and DQPd. BWe enables WRITEs to DQe’s and DQPe. BWf enables WRITEs to DQf’s
and DQPf. BWg enables WRITEs to DQg’s and DQPg. BWh enables WRITEs to DQh’s and DQPh. DQPa-DQPh are avail-
able on the x72 version. DQPa and DQPb are available on the x18 version. DQPa-DQPd are available on the x36 version.
4. All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
5. Wait states are inserted by suspending burst.
6. For a WRITE operation following a READ operation, OE must be HIGH before the input data setup time and held HIGH during the
input data hold time.
7. This device contains circuitry that will ensure the outputs will be in High-Z during power-up.
8. ADSP LOW always initiates an internal READ at the L-H edge of CLK. A WRITE is performed by setting one or more byte write
enable signals and BWE LOW or GW LOW for the subsequent L-H edge of CLK. See WRITE timing diagram for clarification.
Integrated Silicon Solution, Inc. — 1-800-379-4774
13
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
INTERLEAVED BURST ADDRESS TABLE (MODE = VDD or No Connect)
External Address 1st Burst Address 2nd Burst Address 3rd Burst Address
A1 A0 A1 A0 A1 A0 A1 A0
00 01 10 11
01 00 11 10
10 11 00 01
11 10 01 00
LINEAR BURST ADDRESS TABLE (MODE = VSS)
0,0
1,0
0,1A1', A0' = 1,1
ABSOLUTE MAXIMUM RATINGS(1)
Symbol Parameter Value Unit
TSTG Storage Temperature –55 to +150 °C
PDPower Dissipation 1.6 W
IOUT Output Current (per I/O) 100 mA
VIN, VOUT Voltage Relative to Vss for I/O Pins –0.5 to VDDQ + 0.5 V
VIN Voltage Relative to Vss for –0.5 to VDD + 0.5 V
for Address and Control Inputs
VDD Voltage on VDD Supply Relative to Vss –0.5 to 4.6 V
Notes:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause perma-
nent damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
2. This device contains circuity to protect the inputs against damage due to high static voltages or
electric fields; however, precautions may be taken to avoid application of any voltage higher than
maximum rated voltages to this high-impedance circuit.
3. This device contains circuitry that will ensure the output devices are in High-Z at power up.
14
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
OPERATING RANGE (IS61LPSXXXXX)
Range Ambient Temperature VDD VDDQ
Commercial 0°C to +70°C 3.3V + 5% 3.3V / 2.5V + 5%
Industrial –40°C to +85°C 3.3V + 5% 3.3V / 2.5V + 5%
OPERATING RANGE (IS61VPSXXXXX)
Range Ambient Temperature VDD VDDQ
Commercial 0°C to +70°C 2.5V + 5% 2.5V + 5%
Industrial –40°C to +85°C 2.5V + 5% 2.5V + 5%
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
3.3V 2.5V
Symbol Parameter Test Conditions Min. Max. Min. Max. Unit
VOH Output HIGH Voltage IOH = –4.0 mA (3.3V) 2.4 — 2.0 — V
IOH = –1.0 mA (2.5V)
VOL Output LOW Voltage IOL = 8.0 mA (3.3V) — 0.4 — 0.4 V
IOL = 1.0 mA (2.5V)
VIH Input HIGH Voltage 2.0 VDD + 0.3 1.7 VDD + 0.3 V
VIL Input LOW Voltage -0.3 0.8 -0.3 0.7 V
ILI Input Leakage Current Vss ≤ VIN ≤ VDD(1) -5 5 -5 5 µA
ILO Output Leakage Current Vss ≤ VOUT ≤ VDDQ,-55 -55µA
OE = VIH
POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range)
-250 -200
MAX MAX
Symbol Parameter Test Conditions
Temp. range x18 x36 x72 x18 x36 x72 Uni
t
ICC AC Operating Device Selected, Com. 450 450 600 425 425 550 mA
Supply Current OE = VIH, ZZ ≤ VIL, Ind. 500 500 650 475 475 600
All Inputs ≤ 0.2V or ≥ VDD – 0.2V,
Cycle Time ≥ tKC min.
ISB Standby Current Device Deselected, Com. 150 150 150 150 150 150 mA
TTL Input VDD = Max., Ind. 150 150 150 150 150 150
All Inputs ≤ VIL or ≥ VIH,
ZZ ≤ VIL, f = Max.
ISBI Standby Current Device Deselected, Com. 110 110 110 110 110 110 mA
CMOS Input VDD = Max., Ind. 125 125 125 125 125 125
VIN
≤
VSS + 0.2V or ≥VDD – 0.2V
f = 0
ISB2Sleep Mode ZZ>VIH Com. 60 60 60 60 60 60 mA
Ind. 75 75 75 75 75 75
Note:
1. MODE pin has an internal pullup and should be tied to VDD or VSS. It exhibits ±100µA maximum leakage current when tied to ≤
VSS + 0.2V or ≥ VDD – 0.2V.
Integrated Silicon Solution, Inc. — 1-800-379-4774
15
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
CAPACITANCE(1,2)
Symbol Parameter Conditions Max. Unit
CIN Input Capacitance VIN = 0V 6 pF
COUT Input/Output Capacitance VOUT = 0V 8 pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: TA = 25°C, f = 1 MHz, VDD = 3.3V.
3.3V I/O AC TEST CONDITIONS
Parameter Unit
Input Pulse Level 0V to 3.0V
Input Rise and Fall Times 1.5 ns
Input and Output Timing 1.5V
and Reference Level
Output Load See Figures 1 and 2
AC TEST LOADS
Figure 2
317 Ω
5 pF
Including
jig and
scope
351 Ω
OUTPUT
3.3V
Figure 1
Output
Z
O
= 50Ω
1.5V
50Ω
16
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
2.5V I/O AC TEST CONDITIONS
Parameter Unit
Input Pulse Level 0V to 2.5V
Input Rise and Fall Times 1.5 ns
Input and Output Timing 1.25V
and Reference Level
Output Load See Figures 3 and 4
2.5 I/O OUTPUT LOAD EQUIVALENT
Figure 4
317 Ω
5 pF
Including
jig and
scope
351 Ω
OUTPUT
2.5V
Figure 3
Output
ZO
= 50Ω
1.25V
50Ω
Integrated Silicon Solution, Inc. — 1-800-379-4774
17
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
READ/WRITE CYCLE SWITCHING CHARACTERISTICS (Over Operating Range)
-250 -200
Symbol Parameter Min. Max. Min. Max. Unit
fMAX Clock Frequency — 250 — 200 MHz
tKC Cycle Time 4.0 — 5 — ns
tKH Clock High Time 1.7 — 2 — ns
tKL Clock Low Time 1.7 — 2 — ns
tKQ Clock Access Time — 2.6 — 3.1 ns
tKQX
(2)
Clock High to Output Invalid 0.8 — 1.5 — ns
tKQLZ
(2,3)
Clock High to Output Low-Z 0.8 — 1 — ns
tKQHZ
(2,3)
Clock High to Output High-Z — 2.6 — 3.0 ns
tOEQ Output Enable to Output Valid — 2.8 — 3.1 ns
tOELZ
(2,3)
Output Enable to Output Low-Z 0 — 0 — ns
tOEHZ
(2,3)
Output Disable to Output High-Z — 2.6 — 3.0 ns
tAS Address Setup Time 1.2 — 1.4 — ns
tWS Read/Write Setup Time 1.2 — 1.4 — ns
tCES Chip Enable Setup Time 1.2 — 1.4 — ns
tAVS Address Advance Setup Time 1.2 — 1.4 — ns
tDS Data Setup Time 1.2 — 1.4 — ns
tAH Address Hold Time 0.3 — 0.4 — ns
tWH Write Hold Time 0.3 — 0.4 — ns
tCEH Chip Enable Hold Time 0.3 — 0.4 — ns
tAVH Address Advance Hold Time 0.3 — 0.4 — ns
tDH Data Hold Time 0.3 — 0.4 — ns
tPDS ZZ High to Power Down — 2 — 2 cyc
tPUS ZZ Low to Power Down — 2 — 2 cyc
Note:
1. Configuration signal MODE is static and must not change during normal operation.
2. Guaranteed but not 100% tested. This parameter is periodically sampled.
3. Tested with load in Figure 2.
18
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
READ/WRITE CYCLE TIMING
Single Read
High-Z
High-Z
DATA
OUT
DATA
IN
OE
CE2
CE2
CE
BWx
BWE
GW
Address
ADV
ADSC
ADSP
CLK
RD1 RD2
1a 2c 2d
Unselected
Burst Read
t
KQX
t
KC
t
KL
t
KH
t
SS
t
SH
t
SS
t
SH
t
AS
t
AH
t
WS
t
WH
t
WS
t
WH
RD3
t
CES
t
CEH
t
CES
t
CEH
t
CES
t
CEH
CE2 and CE2 only sampled with ADSP or ADSC
CE Masks ADSP
Unselected with CE2
t
OEQ
t
OEQX
t
OELZ
t
KQLZ
t
KQ
t
OEHZ
t
KQHZ
ADSC initiate read
ADSP is blocked by CE inactive
t
AVH
t
AVS Suspend Burst
Pipelined Read
2a 2b
Integrated Silicon Solution, Inc. — 1-800-379-4774
19
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
WRITE CYCLE TIMING
Single Write
DATA
OUT
DATA
IN
OE
CE2
CE2
CE
BWx
BWE
GW
Address
ADV
ADSC
ADSP
CLK
WR1 WR2
Unselected
Burst Write
tKC
tKLtKH
tSS tSH
tAS tAH
tWS tWH
tWS tWH
WR3
tCES tCEH
tCES tCEH
tCES tCEH
CE2 and CE2 only sampled with ADSP or ADSC
CE Masks ADSP
Unselected with CE2
ADSC initiate Write
ADSP is blocked by CE inactive
tAVH
tAVS
ADV must be inactive for ADSP Write
WR1 WR2
tWS tWH
WR3
tWS tWH
High-Z
High-Z 1a 3a
tDS tDH BW4-BW1 only are applied to first cycle of WR2
Write
2c 2d2a 2b
20
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
SNOOZE MODE TIMING
Don't Care
Deselect or Read Only Deselect or Read Only
t
RZZI
CLK
ZZ
Isupply
All Inputs
(except ZZ)
Outputs
(Q)
I
SB2
ZZ setup cycle ZZ recovery cycle
Normal
operation
cycle
t
PDS
t
PUS
t
ZZI
High-Z
SNOOZE MODE ELECTRICAL CHARACTERISTICS
Symbol Parameter Conditions Min. Max. Unit
ISB2Current during SNOOZE MODE ZZ ≥ Vih — 60 mA
tPDS ZZ active to input ignored — 2 cycle
tPUS ZZ inactive to input sampled 2 — cycle
tZZI ZZ active to SNOOZE current — 2 cycle
tRZZI ZZ inactive to exit SNOOZE current 0 — ns
Integrated Silicon Solution, Inc. — 1-800-379-4774
21
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
IEEE 1149.1 SERIAL BOUNDARY SCAN (JTAG)
The IS61LPS/VPSxxxxxx products have a serial boundary
scan Test Access Port (TAP) in the PBGA package only.
(The TQFP package not available.) This port operates in
accordance with
IEEE
Standard 1149.1-1900, but does not
include all functions required for full 1149.1 compliance.
These functions from the
IEEE specification
are excluded
because they place added delay in the critical speed path
of the SRAM. The TAP controller operates in a manner that
does not conflict with the performance of other devices
using 1149.1 fully compliant TAPs. The TAP operates using
JEDEC standard 2.5V I/O logic levels.
DISABLING THE JTAG FEATURE
The SRAM can operate without using the JTAG feature. To
disable the TAP controller, TCK must be tied LOW (Vss) to
prevent clocking of the device. TDI and TMS are internally
pulled up and may be disconnected. They may alternately
be connected to VDD through a pull-up resistor. TDO should
be left disconnected. On power-up, the device will start in a
reset state which will not interfere with the device operation.
TEST ACCESS PORT (TAP) - TEST CLOCK
The test clock is only used with the TAP controller. All
inputs are captured on the rising edge of TCK and outputs
are driven from the falling edge of TCK.
TEST MODE SELECT (TMS)
The TMS input is used to send commands to the TAP
controller and is sampled on the rising edge of TCK. This
pin may be left disconnected if the TAP is not used. The
pin is internally pulled up, resulting in a logic HIGH level.
TEST DATA-IN (TDI)
The TDI pin is used to serially input information to the
registers and can be connected to the input of any
register. The register between TDI and TDO is chosen by
the instruction loaded into the TAP instruction register.
For information on instruction register loading, see the
TAP Controller State Diagram. TDI is internally pulled up
and can be disconnected if the TAP is unused in an
application. TDI is connected to the Most Significant Bit
(MSB) on any register.
31 30 29 . . . 2 1 0
2 1 0
0
x . . . . . 2 1 0
Bypass Register
Instruction Register
Identification Register
Boundary Scan
Register*
TAP CONTROLLER
Selection Circuitry Selection Circuitry TDOTDI
TCK
TMS
TAP CONTROLLER BLOCK DIAGRAM
22
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
TEST DATA OUT (TDO)
The TDO output pin is used to serially clock data-out from
the registers. The output is active depending on the current
state of the
TAP
state machine (see
TAP
Controller State
Diagram). The output changes on the falling edge of TCK
and TDO is connected to the Least Significant Bit (LSB) of
any register.
PERFORMING A TAP RESET
A Reset is performed by forcing TMS HIGH (VDD) for five
rising edges of TCK. RESET may be performed while the
SRAM is operating and does not affect its operation. At
power-up, the TAP is internally reset to ensure that TDO
comes up in a high-Z state.
TAP REGISTERS
Registers are connected between the TDI and TDO pins and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction registers. Data is serially loaded into the TDI
pin on the rising edge of TCK and output on the TDO pin on
the falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruc-
tion register. This register is loaded when it is placed
between the
TDI
and
TDO
pins. (See
TAP
Controller Block
Diagram) At power-up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the
IDCODE instruction if the controller is placed in a reset state
as previously described.
When the TAP controller is in the CaptureIR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers,
it is sometimes advantageous to skip certain states. The
bypass register is a single-bit register that can be placed
between TDI and TDO pins. This allows data to be shifted
through the
SRAM
with minimal delay. The bypass register
is set LOW (VSS) when the BYPASS instruction is ex-
ecuted.
Boundary Scan Register
The boundary scan register is connected to all input and
output pins on the
SRAM
. Several no connect
(NC)
pins are
also included in the scan register to reserve pins for higher
density devices. The x36 configuration has a 75-bit-long
register and the x18 configuration also has a 75-bit-long
register. The boundary scan register is loaded with the
contents of the RAM Input and Output ring when the TAP
controller is in the Capture-DR state and then placed
between the
TDI
and
TDO
pins when the controller is moved
to the
Shift-DR
state. The EXTEST, SAMPLE/PRELOAD
and SAMPLE-Z instructions can be used to capture the
contents of the Input and Output ring.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the
bumps on the SRAM package. The MSB of the register is
connected to TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded to the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP
controller is in the Shift-DR state. The ID register has vendor
code and other information described in the Identification
Register Definitions table.
Scan Register Sizes
Register Bit Size Bit Size Bit Size
Name (x18) (x36) (x72)
Instruction 3 3 3
Bypass 1 1 1
ID 32 32 32
Boundary Scan 75 75
TBD
IDENTIFICATION REGISTER DEFINITIONS
Instruction Field Description 256K x 72 512K x 36 1M x 18
Revision Number (31:28) Reserved for version number. xxxx xxxx xxxx
Device Depth (27:23) Defines depth of SRAM. 512K, 1M or 256K 00110 00111 01000
Device Width (22:18) Defines width of the SRAM. x72, x36 or x18 00101 00100 00011
ISSI Device ID (17:12) Reserved for future use. xxxx xxxxx xxxxx
ISSI JEDEC ID (11:1) Allows unique identification of SRAM vendor. 0011010101 00011010101 00011010101
ID Register Presence (0) Indicate the presence of an ID register. 1 1 1
Integrated Silicon Solution, Inc. — 1-800-379-4774
23
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
TAP INSTRUCTION SET
Eight instructions are possible with the three-bit instruction
register and all combinations are listed in the Instruction Code
table. Three instructions are listed as
RESERVED
and should
not be used and the other five instructions are described
below. The TAP controller used in this SRAM is not fully
compliant with the 1149.1 convention because some man-
datory instructions are not fully implemented. The TAP
controller cannot be used to load address, data or control
signals and cannot preload the
Input
or
Output
buffers. The
SRAM
does not implement the
1149.1
commands
EXTEST
or
INTEST
or the
PRELOAD
portion of
SAMPLE/PRELOAD
; instead
it performs a capture of the
Inputs and Output
ring when these
instructions are executed. Instructions are loaded into the
TAP controller during the Shift-IR state when the instruction
register is placed between TDI and TDO. During this state,
instructions are shifted from the instruction register through
the TDI and TDO pins. To execute an instruction once it is
shifted in, the TAP controller must be moved into the
Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is to be
executed whenever the instruction register is loaded with all
0s. Because EXTEST is not implemented in the TAP
controller, this device is not 1149.1 standard compliant. The
TAP controller recognizes an all-0 instruction. When an
EXTEST instruction is loaded into the instruction register,
the SRAM responds as if a SAMPLE/PRELOAD instruction
has been loaded. There is a difference between the instruc-
tions, unlike the
SAMPLE/PRELOAD
instruction, EXTEST
places the SRAM outputs in a High-Z state.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit
code to be loaded into the instruction register. It also places
the instruction register between the TDI and TDO pins and
allows the IDCODE to be shifted out of the device when the
TAP controller enters the Shift-DR state. The IDCODE
instruction is loaded into the instruction register upon power-
up or whenever the TAP controller is given a test logic reset
state.
SAMPLE-Z
The SAMPLE-Z instruction causes the boundary scan
register to be connected between the TDI and TDO pins
when the TAP controller is in a Shift-DR state. It also places
all SRAM outputs into a High-Z state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction.
The PRELOAD portion of this instruction is not imple-
mented, so the TAP controller is not fully 1149.1 compliant.
When the SAMPLE/PRELOAD instruction is loaded to the
instruction register and the TAP controller is in the Capture-
DR state, a snapshot of data on the inputs and output pins
is captured in the boundary scan register.
It is important to realize that the TAP controller clock
operates at a frequency up to 10 MHz, while the SRAM
clock runs more than an order of magnitude faster. Because
of the clock frequency differences, it is possible that during
the Capture-DR state, an input or output will under-go a
transition. The TAP may attempt a signal capture while in
transition (metastable state). The device will not be harmed,
but there is no guarantee of the value that will be captured
or repeatable results.
To guarantee that the boundary scan register will capture
the correct signal value, the SRAM signal must be stabi-
lized long enough to meet the TAP controller’s capture set-
up plus hold times (tCS and tCH). To insure that the SRAM
clock input is captured correctly, designs need a way to stop
(or slow) the clock during a SAMPLE/PRELOAD instruc-
tion. If this is not an issue, it is possible to capture all other
signals and simply ignore the value of the CLK captured in
the boundary scan register.
Once the data is captured, it is possible to shift out the data
by putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO pins.
Note that since the
PRELOAD
part of the command is not
implemented, putting the
TAP
into the
Update
to the
Update-DR
state while performing a
SAMPLE/PRELOAD
instruction will
have the same effect as the Pause-DR command.
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the
bypass register is placed between the TDI and TDO pins.
The advantage of the BYPASS instruction is that it shortens
the boundary scan path when multiple devices are con-
nected together on a board.
RESERVED
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
24
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
INSTRUCTION CODES
Code Instruction Description
000 EXTEST Captures the Input/Output ring contents. Places the boundary scan register between
the TDI and TDO. Forces all SRAM outputs to High-Z state. This
instruction is not 1149.1 compliant.
001 IDCODE Loads the ID register with the vendor ID code and places the register between TDI
and TDO. This operation does not affect SRAM operation.
010 SAMPLE-Z Captures the Input/Output contents. Places the boundary scan register between TDI
and TDO. Forces all SRAM output drivers to a High-Z state.
011 RESERVED Do Not Use: This instruction is reserved for future use.
100
SAMPLE/PRELOAD
Captures the Input/Output ring contents. Places the boundary scan register between
TDI and TDO. Does not affect the SRAM operation. This instruction does not
implement 1149.1 preload function and is therefore not 1149.1 compliant.
101 RESERVED Do Not Use: This instruction is reserved for future use.
110 RESERVED Do Not Use: This instruction is reserved for future use.
111 BYPASS Places the bypass register between TDI and TDO. This operation does not
affect SRAM operation.
Select DR
Capture DR
Shift DR
Exit1 DR
Pause DR
Exit2 DR
Update DR
Select IR
Capture IR
Shift IR
Exit1 IR
Pause IR
Exit2 IR
Update IR
Test Logic Reset
Run Test/Idle 11 1
11
11
1
1
11
11
1
0
0
0
0
1
00
0
0
0
0
0
0
0
0
0
10
TAP CONTROLLER STATE DIAGRAM
Integrated Silicon Solution, Inc. — 1-800-379-4774
25
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
TAP Electrical Characteristics Over the Operating Range(1,2)
Symbol Parameter Test Conditions Min. Max. Units
VOH1 Output HIGH Voltage IOH = –2.0 mA 1.7 — V
VOH2 Output HIGH Voltage IOH = –100
µ
A 2.1 — V
VOL1 Output LOW Voltage IOL = 2.0 mA — 0.7 V
VOL2 Output LOW Voltage IOL = 100
µ
A — 0.2 V
VIH Input HIGH Voltage 1.7 VDD +0.3 V
VIL Input LOW Voltage –0.3 0.7 V
IXInput Leakage Current VSS ≤ V I ≤ VDDQ –10 10
µ
A
Notes:
1. All Voltage referenced to Ground.
2. Overshoot: VIH (AC) ≤ VDD +1.5V for t ≤ tTCYC/2,
Undershoot: VIL (AC) ≤ 0.5V for t ≤ tTCYC/2,
Power-up: VIH < 2.6V and VDD < 2.4V and VDDQ < 1.4V for t < 200 ms.
TAP AC ELECTRICAL CHARACTERISTICS(1,2) (OVER OPERATING RANGE)
Symbol Parameter Min. Max. Unit
tTCYC TCK Clock cycle time 100 — ns
fTF TCK Clock frequency — 10 MHz
tTH TCK Clock HIGH 40 — ns
tTL TCK Clock LOW 40 — ns
tTMSS TMS setup to TCK Clock Rise 10 — ns
tTDIS TDI setup to TCK Clock Rise 10 — ns
tCS Capture setup to TCK Rise 10 — ns
tTMSH
TMS hold after TCK Clock Rise
10 — ns
tTDIH TDI Hold after Clock Rise 10 — ns
tCH Capture hold after Clock Rise 10 — ns
tTDOV TCK LOW to TDO valid — 20 ns
tTDOX TCK LOW to TDO invalid 0 — ns
Notes:
1. Both tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register.
2. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns.
26
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
DON'T CARE
UNDEFINED
TCK
TMS
TDI
TDO
tTHTL
tTLTH
tTHTH
tMVTH tTHMX
tDVTH tTHDX
1 2 3 4 5 6
tTLOX
tTLOV
TAP TIMING
20 pF
TDO
GND
50Ω
Vtrig
Z0 = 50Ω
TAP Output Load Equivalent
TAP AC TEST CONDITIONS (2.5V/3.3V)
Input pulse levels 0 to 2.5V/0 to 3.0V
Input rise and fall times 1ns
Input timing reference levels 1.25V/1.5V
Output reference levels 1.25V/1.5V
Test load termination supply voltage 1.25V/1.5V
Vtrig 1.25V/1.5V
Integrated Silicon Solution, Inc. — 1-800-379-4774
27
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
209 BOUNDARY SCAN ORDER (256K X 72)
28
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
165 PBGA BOUNDARY SCAN ORDER (x 36)
Signal Bump Signal Bump Signal Bump Signal Bump
Bit # Name ID Bit # Name ID Bit # Name ID Bit # Name ID
1 MODE 1R 21 DQb 11G 41 NC 1A 61 DQd 1J
2 A 6N 22 DQb 11F 42 CE2 6A 62 DQd 1K
3 A 11P 23 DQb 11E 43 BWa 5B 63 DQd 1L
4 A 8P 24 DQb 11D 44 BWb 5A 64 DQd 1M
5 A 8R 25 DQb 10G 45 BWc 4A 65 DQd 2J
6 A 9R 26 DQb 10F 46 BWd 4B 66 DQd 2K
7 A 9P 27 DQb 10E 47 CE2 3B 67 DQd 2L
8 A 10P 28 DQb 10D 48 CE 3A 68 DQd 2M
9 A 10R 29 DQb 11C 49 A 2A 69 DQd 1N
10 A 11R 30 NC 11A 50 A 2B 70 A 3P
11 ZZ 11H 31 A 10A 51 NC 1B 71 A 3R
12 DQa 11N 32 A 10B 52 DQc 1C 72 A 4R
13 DQa 11M 33 ADV 9A 53 DQc 1D 73 A 4P
14 DQa 11L 34 ADSP 9B 54 DQc 1E 74 A1 6P
15 DQa 11K 35 ADSC 8A 55 DQc 1F 75 A0 6R
16 DQa 11J 36 OE 8B 56 DQc 1G
17 DQa 10M 37 BWE 7A 57 DQc 2D
18 DQa 10L 38 GW 7B 58 DQc 2E
19 DQa 10K 39 CLK 6B 59 DQc 2F
20 DQa 10J 40 NC 11B 60 DQc 2G
Integrated Silicon Solution, Inc. — 1-800-379-4774
29
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
165 PBGA BOUNDARY SCAN ORDER (x 18)
Signal Bump Signal Bump Signal Bump Signal Bump
Bit # Name ID Bit # Name ID Bit # Name ID Bit # Name ID
1 MODE 1R 21 DQa 11G 41 NC 1A 61 DQb 1J
2 A 6N 22 DQa 11F 42 CE2 6A 62 DQb 1K
3 A 11P 23 DQa 11E 43 BWa 5B 63 DQb 1L
4 A 8P 24 DQa 11D 44 NC 5A 64 DQb 1M
5 A 8R 25 DQa 11C 45 BWb 4A 65 DQb 1N
6 A 9R 26 NC 10F 46 NC 4B 66 NC 2K
7 A 9P 27 NC 10E 47 CE2 3B 67 NC 2L
8 A 10P 28 NC 10D 48 CE 3A 68 NC 2M
9 A 10R 29 NC 10G 49 A 2A 69 NC 2J
10 A 11R 30 A 11A 50 A 2B 70 A 3P
11 ZZ 11H 31 A 10A 51 NC 1B 71 A 3R
12 NC 11N 32 A 10B 52 NC 1C 72 A 4R
13 NC 11M 33 ADV 9A 53 NC 1D 73 A 4P
14 NC 11L 34 ADSP 9B 54 NC 1E 74 A1 6P
15 NC 11K 35 ADSC 8A 55 NC 1F 75 A0 6R
16 NC 11J 36 OE 8B 56 NC 1G
17 DQa 10M 37 BWE 7A 57 DQb 2D
18 DQa 10L 38 GW 7B 58 DQb 2E
19 DQa 10K 39 CLK 6B 59 DQb 2F
20 DQa 10J 40 NC 11B 60 DQb 2G
30
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
ORDERING INFORMATION (3.3V core/2.5V-3.3V I/O)
Commercial Range: 0°C to +70°C
Configuration Frequency Order Part Number Package
512Kx36
250 IS61LPS51236A-250TQ 100 TQFP
IS61LPS51236A-250TQL 100 TQFP, Lead-free
IS61LPS51236A-250B2 119 PBGA
IS61LPS51236A-250B3 165 PBGA
200 IS61LPS51236A-200TQ 100 TQFP
IS61LPS51236A-200B2 119 PBGA
IS61LPS51236A-200B3 165 PBGA
1Mx18
250 IS61LPS102418A-250TQ 100 TQFP
IS61LPS102418A-250B2 119 PBGA
IS61LPS102418A-250B3 165 PBGA
200 IS61LPS102418A-200TQ 100 TQFP
IS61LPS102418A-200B2 119 PBGA
IS61LPS102418A-200B3 165 PBGA
256Kx72 250 IS61LPS25672A-250B1 209 PBGA
IS61LPS25672A-250B1L 209 PBGA, Lead-free
Industrial Range: -40°C to +85°C
Configuration Frequency Order Part Number Package
512Kx36
250 IS61LPS51236A-250TQI 100 TQFP
IS61LPS51236A-250B2I 119 PBGA
IS61LPS51236A-250B3I 165 PBGA
IS61LPS51236A-250B3LI 165 PBGA, Lead-free
200 IS61LPS51236A-200TQI 100 TQFP
IS61LPS51236A-200TQLI 100 TQFP, Lead-free
IS61LPS51236A-200B2I 119 PBGA
IS61LPS51236A-200B2LI 119 PBGA, Lead-free
IS61LPS51236A-200B3I 165 PBGA
IS61LPS51236A-200B3LI 165 PBGA, Lead-free
1Mx18
250 IS61LPS102418A-250TQI 100 TQFP
IS61LPS102418A-250TQLI 100 TQFP, Lead-free
IS61LPS102418A-250B2I 119 PBGA
IS61LPS102418A-250B3I 165 PBGA
200 IS61LPS102418A-200TQI 100 TQFP
IS61LPS102418A-200TQLI 100 TQFP, Lead-free
IS61LPS102418A-200B2I 119 PBGA
IS61LPS102418A-200B3I 165 PBGA
256Kx72 250 IS61LPS25672A-250B1I 209 PBGA
Integrated Silicon Solution, Inc. — 1-800-379-4774
31
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
ORDERING INFORMATION (2.5V core/2.5V I/O)
Commercial Range: 0°C to +70°C
Configuration Frequency Order Part Number Package
512Kx36
250 IS61VPS51236A-250TQ 100 TQFP
IS61VPS51236A-250B2 119 PBGA
IS61VPS51236A-250B3 165 PBGA
IS61VPS51236A-250B3L 165 PBGA, Lead-free
200 IS61VPS51236A-200TQ 100 TQFP
IS61VPS51236A-200B2 119 PBGA
IS61VPS51236A-200B3 165 PBGA
1Mx18
250 IS61VPS102418A-250TQ 100 TQFP
IS61VPS102418A-250TQL 100 TQFP, Lead-free
IS61VPS102418A-250B2 119 PBGA
IS61VPS102418A-250B3 165 PBGA
200 IS61VPS102418A-200TQ 100 TQFP
IS61VPS102418A-200B2 119 PBGA
IS61VPS102418A-200B3 165 PBGA
256Kx72 250 IS61VPS25672A-250B1 209 PBGA
Industrial Range: -40°C to +85°C
Configuration Frequency Order Part Number Package
512Kx36
250 IS61VPS51236A-250TQI 100 TQFP
IS61VPS51236A-250B2I 119 PBGA
IS61VPS51236A-250B3I 165 PBGA
200 IS61VPS51236A-200TQI 100 TQFP
IS61VPS51236A-200TQLI 100 TQFP, Lead-free
IS61VPS51236A-200B2I 119 PBGA
IS61VPS51236A-200B3I 165 PBGA
1Mx18
250 IS61VPS102418A-250TQI 100 TQFP
IS61VPS102418A-250B2I 119 PBGA
IS61VPS102418A-250B3I 165 PBGA
200 IS61VPS102418A-200TQI 100 TQFP
IS61VPS102418A-200B2I 119 PBGA
IS61VPS102418A-200B3I 165 PBGA
256Kx72 250 IS61VPS25672A-250B1I 209 PBGA
32
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
Integrated Silicon Solution, Inc. — 1-800-379-4774
33
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
1. CONTROLLING DIMENSION : MM .
NOTE :
2. Reference document : JEDEC MS-028
10/02/2008
Package Outline
34
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
1. CONTROLLING DIMENSION : MM .
NOTE :
Package Outline 08/28/2008
Integrated Silicon Solution, Inc. — 1-800-379-4774
35
Rev. M
01/20/2010
IS61VPS25672A, IS61LPS25672A
IS61VPS51236A, IS61LPS51236A, IS61VPS102418A, IS61LPS102418A
1. Controlling dimension : mm
NOTE :
Package Outline
12/10/2007
