[ /Title (CD45 41B) /Subject (CMO S Programmable Timer High Voltage Types (20V Rating)) /Autho r () /Keywords (Harris Semiconductor, CD400 0, metal gate, CMOS , pdip, cerdip, mil, military, mil CD4541B CMOS Programmable Timer High Voltage Types (20V Rating) Data sheet acquired from Harris Semiconductor SCHS085E - Revised September 2003 Features The output from this timer is the Q or Q output from the 8th, 10th, 13th, or 16th counter stage. The desired stage is chosen using time-select inputs A and B (see Frequency Select Table). * Low Symmetrical Output Resistance, Typically 100 at VDD = 15V The output is available in either of two modes selectable via the MODE input, pin 10 (see Truth Table). When this MODE input is a logic "1", the output will be a continuous square wave having a frequency equal to the oscillator frequency divided by 2N. With the MODE input set to logic "0" and after a MASTER RESET is initiated, the output (assuming Q output has been selected) changes from a low to a high state after 2N-1 counts and remains in that state until another MASTER RESET pulse is applied or the MODE input is set to a logic "1". * Built-In Low-Power RC Oscillator * Oscillator Frequency Range . . . . . . . . . . DC to 100kHz * External Clock (Applied to Pin 3) can be Used Instead of Oscillator * Operates as 2N Frequency Divider or as a SingleTransition Timer * Q/Q Select Provides Output Logic Level Flexibility * AUTO or MASTER RESET Disables Oscillator During Reset to Reduce Power Dissipation Timing is initialized by setting the AUTO RESET input (pin 5) to logic "0" and turning power on. If pin 5 is set to logic "1", the AUTO RESET circuit is disabled and counting will not start until after a positive MASTER RESET pulse is applied and returns to a low level. The AUTO RESET consumes an appreciable amount of power and should not be used if low-power operation is desired. For reliable automatic power-on reset, VDD should be greater than 5V. * Operates With Very Slow Clock Rise and Fall Times * Capable of Driving Six Low Power TTL Loads, Three Low-Power Schottky Loads, or Six HTL Loads Over the Rated Temperature Range * Symmetrical Output Characteristics * 100% Tested for Quiescent Current at 20V The RC oscillator, shown in Figure 2, oscillates with a frequency determined by the RC network and is calculated using: * 5V, 10V, and 15V Parametric Ratings * Meets All Requirements of JEDEC Standard No. 13B, "Standard Specifications for Description of `B' Series CMOS Devices" 1 f = ----------------------------------2.3 R TC C TC Description CD4541B programmable timer consists of a 16-stage binary counter, an oscillator that is controlled by external R-C components (2 resistors and a capacitor), an automatic power-on reset circuit, and output control logic. The counter increments on positive-edge clock transitions and can also be reset via the MASTER RESET input. Ordering Information PART NUMBER Pinout CD4541B (CERDIP, PDIP, SOIC, SOP, TSSOP) TOP VIEW RTC 1 14 VDD CTC 2 13 B RS 3 12 A NC 4 11 NC AUTO RESET 5 Where f is between 1kHz and 100kHz and R S 10k and 2R TC TEMP. RANGE (oC) -55 to 125 14 Ld CERDIP CD4541BE -55 to 125 14 Ld PDIP CD4541BM -55 to 125 14 Ld SOIC CD4541BMT -55 to 125 14 Ld SOIC CD4541BM96 -55 to 125 14 Ld SOIC CD4541BNSR -55 to 125 14 Ld SOP CD4541BPW -55 to 125 14 Ld TSSOP CD4541BPWR -55 to 125 14 Ld TSSOP NOTE: When ordering, use the entire part number. The suffixes 96 and R denote tape and reel. The suffix T denotes a small-quantity reel of 250. 10 MODE MASTER RESET 6 9 Q/Q SELECT VSS 7 8 OUTPUT CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) 2003, Texas Instruments Incorporated PACKAGE CD4541BF3A 1 CD4541B Functional Diagram 12 A 13 B 1 RTC 2 CTC 3 RS 5 AR 6 MR 10 MODE 9 Q/Q SELECT 8 Q VDD = PIN 14 VSS = PIN 7 12 13 A B R N P Q 1 OF 3 MUX N P 3 RS CTC RTC 2 210 213 8-STAGE COUNTER OSC 1 AUTO RESET 9 216 OR 28 Q/Q SELECT VDD 8-STAGE COUNTER R R 10 MODE R 5 8 PWR ON RESET VSS VDD = 14 VSS = 7 6 MANUAL RESET All inputs are protected by CMOS Protection Network. NC = 4, 11 FIGURE 1. FREQUENCY SELECTION TABLE A B NO. OF STAGES N COUNT 2N 0 0 13 8192 0 1 10 1024 1 0 8 256 1 1 16 65536 3 RS CTC TRUTH TABLE STATE PIN 0 TO CLOCK CKT 2 INTERNAL RESET 1 1 5 Auto Reset On 6 Master Reset Off Master Reset On 9 Output Initially Low After Reset (Q) Output Initially High After Reset (Q) 10 Single Transition Mode Recycle Mode RTC Auto Reset Disable FIGURE 2. RC OSCILLATOR CIRCUIT 2 CD4541B Absolute Maximum Ratings Thermal Information DC Supply - Voltage Range, VDD Voltages Referenced to VSS Terminal . . . . . . . . . . -0.5V to +20V Input Voltage Range, All Inputs . . . . . . . . . . . . . -0.5V to VDD +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . 10mA Device Dissipation Per Output Transistor For TA = Full Package Temperature Range (All Package Types) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mW Package Thermal Impedance, JA (see Note 1) PDIP package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80oC/W SOIC package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86oC/W SOP package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76oC/W TSSOP package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113oC/W Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range (TSTG) . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) At Distance 1/16in 1/32in (1.59mm 0.79mm) from case for 10s Maximum . . . . . . . . . . . . . . . . . . . . . . . . 265oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range TA . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range For TA = Full Package Temperature Range . . . . . 3V (Min), 18V (Typ) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. Electrical Specifications LIMITS AT INDICATED TEMPERATURES (oC) CONDITIONS PARAMETER Quiescent Device Current, (Note 2) IDD (Max) Output Low (Sink) Current lOL (Min) Output High (Source) Current, IOH (Min) Output Voltage: Low-Level, VOL (Max) Output Voltage: High-Level, VOH (Min) Input Low Voltage, VIL (Max) 25 VO (V) VIN (V) VDD (V) -55 -40 85 125 MIN TYP MAX UNITS - 0, 5 5 5 5 150 150 - 0.04 5 A - 0, 10 10 10 10 300 300 - 0.04 10 A - 0, 15 15 20 20 600 600 - 0.04 20 A - 0, 20 20 100 100 3000 3000 - 0.08 100 A 0.4 0, 5 5 1.9 1.85 1.26 1.08 1.55 3.1 - mA 0.5 0, 10 10 5 4.8 3.3 2.8 4 8 - mA 1.5 0, 15 15 12.6 12 8.4 7.2 10 20 - mA 4.6 0, 5 5 -1.9 -1.85 -1.26 -1.08 -1.55 -3.1 - mA 2.5 0, 5 5 -6.2 -6 -4.1 -3 -5 -10 - mA 9.5 0, 10 10 -5 -4.8 -3.3 -2.8 -4 -8 - mA 13.5 0, 15 15 -12.6 -12 -8.4 -7.2 -10 -20 - mA - 0, 5 5 - 0.05 - 0 0.05 V - 0, 10 10 - 0.05 - 0 0.05 V - 0, 15 15 - 0.05 - 0 0.05 V - 0, 5 5 - 4.95 4.95 5 - V - 0, 10 10 - 9.95 9.95 10 - V - 0, 15 15 - 14.95 14.95 15 - V 0.5, 4.5 - 5 - 1.5 - - 1.5 V 1, 9 - 10 - 3 - - 3 V 1.5, 13.5 - 15 - 4 - - 4 V 3 CD4541B Electrical Specifications (Continued) LIMITS AT INDICATED TEMPERATURES (oC) CONDITIONS 25 VO (V) VIN (V) VDD (V) -55 0.5, 4.5 - 5 - 1, 9 - 10 1.5, 13.5 - - 0, 18 PARAMETER Input High Voltage, VIH (Min) Input Current, lIN (Max) -40 85 MIN TYP MAX UNITS 3.5 3.5 - - V - 7 7 - - V 15 - 11 11 - - V 18 0.1 - 10-5 0.1 A 0.1 1 125 1 NOTE: 2. With AUTO RESET enabled, additional current drain at 25oC is: 7A (Typ), 200A (Max) at 5V; 30A (Typ), 350A (Max) at 10V; 80A (Typ), 500A (Max) at 15V Dynamic Electrical Specifications PARAMETER Propagation Delay Times Clock to Q TA = 25oC, Input tr , tf = 20ns, CL = 50pF, RL = 200k SYMBOL VDD (V) MIN TYP MAX UNITS (28) tPHL , tPLH 5 - 3.5 10.5 s 10 - 1.25 3.8 s 15 - 0.9 2.9 s 5 - 6.0 18 s 10 - 3.5 10 s 15 - 2.5 7.5 s 5 - 100 200 ns 10 - 50 100 ns 15 - 40 80 ns 5 - 180 360 ns 10 - 90 180 ns 15 - 65 130 ns 5 900 300 - ns 10 300 100 - ns 15 225 85 - ns 5 - 1.5 - MHz 10 - 4 - MHz 15 - 6 - MHz (216) tPHL , tPLH Transition Time tTHL tTHL MASTER RESET, CLOCK Pulse Width Maximum Clock Pulse Input Frequency Maximum Clock Pulse Input Rise or Fall time fCL tr , tf 5, 10, 15 Unlimited 4 s CD4541B Digital Timer Application A positive pulse on MASTER RESET resets the counters and latch. The output goes high and remains high until the number of pulses, selected by A and B, are counted. This circuit is retriggerable and is as accurate as the input frequency. If additional accuracy is desired, an external clock can be used on pin 3. A setup time equal to the width of the one-shot output is required immediately following initial power up, during which time the output will be high. VDD RTC CTC RS AR MR INPUT 1 14 2 3 4 5 6 13 12 11 10 9 7 8 B A OUTPUT t FIGURE 3. DIGITAL TIMER APPLICATION CIRCUIT 5 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD4541BEE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD4541BF ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type CD4541BF3A ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type CD4541BM ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BM96 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BM96E4 ACTIVE SOIC D 14 CD4541BM96G4 ACTIVE SOIC D 14 CD4541BME4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BMG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BMT ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BMTE4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BMTG4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BNSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BNSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BNSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BPWE4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TBD Addendum-Page 1 Samples (Requires Login) CD4541BE TBD (3) Call TI Call TI Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp CD4541BPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BPWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4541BPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF CD4541B, CD4541B-MIL : * Catalog: CD4541B * Military: CD4541B-MIL Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing CD4541BM96 SOIC D 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 6.5 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 9.0 2.1 8.0 16.0 Q1 CD4541BMT SOIC D 14 250 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD4541BNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 CD4541BPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD4541BM96 SOIC D 14 2500 367.0 367.0 38.0 CD4541BMT SOIC D 14 250 367.0 367.0 38.0 CD4541BNSR SO NS 14 2000 367.0 367.0 38.0 CD4541BPWR TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated