FTR-K1 SERIES POWER RELAY 1 POLE - 25A - 1.5mm contact gap FTR-K3-WG Series n FEATURES 1 pole, 25A 1 Form A l Contact gap 1.5mm Surge strength (B/T open contacts) 2.5kV Compliance with European photovoltaic standard (VDE0126) l High insulation in small package (between coil and contact) - Insulation distance: Clearance > 6.4mm Creepage > 9.5mm - Dielectric strength: 5,000VAC - Surge strength: 8,500V l Coil holding voltage can be reduced up to 35% of nominal coil voltage (ambient temperature; +20 C, contact current; 25A) Power consumption at the lowest coil holding voltage; 95mW * Coil holding voltage is the coil voltage after 100ms of applied nominal coil voltage l Flammability UL94V-0 (plastics) l Cadmium-free contacts l Flux free, cat. RTII protection l RoHS compliant Please see page 6 for more information l l PARTNUMBER INFORMATION n [Example] FTR-K3 (a) A (b) B (c) 012 (d) W - WG (e) (f) (a) Relay type FTR-K3 : FTR-K3-Series (b) Contact configuration A : 1 form A / PCB type (c) Coil power B : Standard type (780mW) (d) Coil rated voltage 012 : 5.....48 VDC Coil rating table at page 3 (e) Contact material W : Silver alloy (f) Option code WG : Contact gap 1.5mm Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K3AB012W-WG Actual marking: K3AB012W-WG 1 FTR-K1 SERIES FTR-K3-WG SERIES n SPECIFICATION Item Contact Data FTR-K3-WG Configuration 1 form A Material Silver alloy Resistance (initial) Max. 100m at 1A, 6VDC Contact rating 25A, 250VAC (resistive) Max. carrying current 25A Max. switching voltage 250VAC Max. switching power 6,250VA Max. switching current 25A Min. switching load * 100mA, 5VDC (reference value) Mechanical Min. 2 x 106 operations Electrical (resistive) 25A / 250VAC, min. 100 x 103 operations Electrical (inductive) Endurance: 25A, 250VAC, cos = 0.8, min. 30 x 103 operations Overload: 37.5A, 250VAC, cos = 0.8, min. 50 operations Rated power (at 20 C) Approximately 780mW Operate power (at 20 C) Approximately 380mW Coil power at holding voltage 95mW (35% of nominal coil voltage) Holding voltage *2 35~120% of nominal coil voltage (25A at +20 C) 40~80% of nominal coil voltage (25A at +85 C) Operating temperature range -40 C to +60 C (coil nominal voltage) -40 C to +85 C (holding voltage; 40~80% of nominal coil voltage) Operate (at nominal voltage) Max. 20ms (without bounce) Release (at nominal voltage) Max. 10ms (no diode, without bounce) Contact gap (initial) Min. 1.5 mm Resistance Min. 1,000M at 500VDC 1 Life Coil Data Timing Data Insulation Dielectric strength Surge strength Other Vibration resistance Shock resistance Weight Open contacts 2,500VAC, 1min. Coil and contacts 5,000VAC, 1min. Coil to contacts 8,500V / 1.2 x 50s standard wave Misoperation 10 to 55Hz double amplitude 1.5 mm Endurance 10 to 55Hz double amplitude 1.5 mm Misoperation Min. 200m/s (11 1ms) Endurance Min. 1,000m/s (6 1ms) Approximately 25 g *1 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. *2 Reduction of minimum coil holding voltage to maximum coil voltage range, after 100msec energizing with nominal coil voltage. 2 FTR-K1 SERIES FTR-K3-WG SERIES COIL RATING n Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) *1 Must Release Voltage (VDC) *1 Min. Non Release Voltage (VDC) *1 005 5 32 3.5 0.5 1.75 006 6 46 4.2 0.6 2.1 009 9 105 6.3 0.9 3.15 012 12 185 8.4 1.2 4.2 018 18 415 12.6 1.8 6.3 024 24 740 16.8 2.4 8.4 048 48 2,955 33.6 4.8 16.8 Rated Power +/- 10% (mW) Approx. 780 (97)*2 Note: All values in the table are valid for 20C and zero contact current. *1 Specified operate values are valid for pulse wave voltage. *2 This value is the coil power at 35% of nominal voltage at 20C. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 E63614 25A, 277VAC (resistive, at 60 C) 1HP, 125VAC (at 60 C) 2HP, 277VAC, 100x103 (at 60 C) VDE IEC61810-1 25A, 250VAC (cos =1 at 60 C) CQC GB15092.1, GB8898 GB/T21711.1 04001009179 20A, 250VAC 3 FTR-K1 SERIES FTR-K3-WG SERIES n REFERENCE DATA Electrical life tests (resistive load) 4 FTR-K1 SERIES FTR-K3-WG SERIES n DIMENSIONS l l Dimensions l Schematics (BOTTOM VIEW) PC board mounting hole layout (BOTTOM VIEW) Unit: mm 5 FTR-K1 SERIES FTR-K3-WG SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1 SERIES FTR-K3-WG SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 13, 2011 7