Series AM10EW-Z
10 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.G 1 of 3 North America only
FEATURES:
Models
Single output
Model
Input Voltage
(V)
Output Voltage
(V)
Output Current
max (A)
Capacitive load
max (μF)
Efficiency
(%)
AM10EW-2403SZ
9-36
3.3
2
3300
80
AM10EW-2405SZ
9-36
5
2
3300
82
AM10EW-2412SZ
9-36
12
0.83
680
85
AM10EW-2415SZ
9-36
15
0.67
470
85
AM10EW-4803SZ
18-72
3.3
2
3300
79
AM10EW-4805SZ
18-72
5
2
3300
82
AM10EW-4812SZ
18-72
12
0.83
680
85
AM10EW-4815SZ
18-72
15
0.67
470
85
Models
Dual output
Model
Input Voltage
(V)
Output Voltage
(V)
Output Current
max (A)
Capacitive load
(μF)
Efficiency
(%)
AM10EW-2405DZ
9-36
±5
±1
±2200
82
AM10EW-2412DZ
9-36
±12
±0.416
±470
85
AM10EW-2415DZ
9-36
±15
±0.333
±330
85
AM10EW-4805DZ
18-72
±5
±1
±2200
82
AM10EW-4812DZ
18-72
±12
±0.416
±470
85
AM10EW-4815DZ
18-72
±15
±0.333
±330
85
Input Specifications
Parameters
Nominal
Typical
Maximum
Units
Voltage range
24
9-36
VDC
48
18-72
Filter
(Pi) Network
Remote ON/OFF Control
ON
2.5~5.5 or open circuit
VDC
OFF
-0.7~ 0.8 or short circuit b/n pin 2 & 1
Turn on Transient process time
350
ms
Start up time
20
ms
Absolute Maximum Rating
24 Vin
-0.7-40
VDC
48 Vin
-0.7-80
Peak Input Voltage time
100
ms
Isolation Specifications
Parameters
Conditions
Typical
Rated
Units
Tested I/O voltage
3 sec
1500
VDC
Case/ Input & Output
1000
VDC
Resistance
> 1000
MOhm
Capacitance
1200
pF
• RoHS compliant
• Low ripple and noise
• Efficiency up to 85%
• Remote on/off control
• Wide 4:1 input range
● Input/Output Isolation 1500VDC
• Continuous Short Circuit Protection
● Operating temperature -40oC to + 85oC
Click on Series name for product info on aimtec.com
Series AM10EW-Z
10 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.G 2 of 3 North America only
Output Specifications
Parameters
Conditions
Typical
Maximum
Units
Voltage accuracy
±1
%
Voltage balance (Dual output)
Balance Load
±1
%
Short Circuit protection
Continuous
Short Circuit restart
Auto Recovery
Current limiting
140
% of Iout max
Line voltage regulation
HL-LL
±0.5
%
Load voltage regulation
10-100% load
±1.0
%
Temperature coefficient
±0.02
%/oC
Ripple & Noise
20Mhz bandwidth
75
mV p-p
Rising time
10
ms
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Switching frequency
100% load
300
KHz
Operating temperature
No derating
-40 to +85
oC
Storage temperature
-40 to +125
oC
Max case temperature
100
oC
Cooling
Free air convection
Humidity
95
%
Case material
Nickel coated copper
Weight
31
g
Dimensions (L x W x H)
Tolerance ±0.5mm
2.00 x 1.00 x 0.40 inches 50.80 x 25.00 x 10.16 mm
MTBF
>1 121 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC)
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input
voltage and at rated output load unless otherwise specified.
Safety Specifications
Parameters
Agency Approvals
CE, cULus
Standards
IEC/UL/EN/62368-1
EN55032 Class A
IEC61000-4-2, Perf. Criteria B
IEC61000-4-3, Perf. Criteria A
IEC61000-4-4, Perf. Criteria B
IEC61000-4-6, Perf. Criteria A
IEC61000-4-8, Perf. Criteria A
Pin Out Specifications
Pin
Single
Dual
1
On/Off Control
On/Off Control
2
-V Input
-V Input
3
+V Input
+V Input
4
-V Output
-V Output
5
No Pin
Common
6
+V Output
+V Output
Series AM10EW-Z
10 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.G 3 of 3 North America only
Dimensions
Test Circuit
Conducted Emissions
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
5.08
(0.20)
Min
Notes:
All dimensions are typical
in millimeters (inches).
Tolerance ±0.25 (±0.01)
DIA
1.00
(0.04)
50.80
(2.00)
25.40
(1.00)
10.16
(0.40)
Built-in Stand-offs to
ease PCB cleaning
1
2
3
4
5
Bottom View
20.32
(0.80)
15.24
(0.60)15.24
(0.60)
7.62
(0.30) 10.16
(0.40)
5.08
(0.20)
10.16
(0.40)
10.16
(0.40)
6
2.54
(0.10)
2.54
(0.10)
