▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_smd_NR_NS_reli_e-01
12. Adhesion of terminal electrode
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
Shall not come off PC board
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow.
Applied force : 10N to X and Y directions.
Duration : 5s.
Solder cream thickness : 0.15mm.
NR10050 Type :
Applied force : 5N to X and Y directions.
Duration : 5s.
13. Resistance to vibration
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test samples shall be soldered to the test board by the reflow.
Then it shall be submitted to below test conditions.
Frequency Range 10~55Hz
Total Amplitude 1.5mm (May not exceed acceleration 196m/s2)
Sweeping Method 10Hz to 55Hz to 10Hz for 1min.
Time
X
For 2 hours on each X, Y, and Z axis. Y
Z
Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs.
14. Solderability
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type
At least 90% of surface of terminal electrode is covered by new solder.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table.
Flux : Methanol solution containing rosin 25%.
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type
Solder Temperature 245±5℃
Time 5±1.0 sec.
※Immersion depth : All sides of mounting terminal shall be immersed.
15. Resistance to soldering heat
Specified Value
NR30/40/50/60/80, NRV20/30,
NRH24/30, NRS20/40/50/60/80 Type Inductance change : Within ±10%
No significant abnormality in appearance.
NR10050 Type
NS101, NS125 Type
Test Methods and
Remarks
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80 Type, NR10050 Type, NS101/125 Type :
The test sample shall be exposed to reflow oven at 230±5℃ for 40 seconds, with peak temperature at 260±5℃ for 5 seconds, 2 times.
NR30/40/50/60/80, NRV20/30, NRH24/30, NRS20/40/50/60/80Type, NS101/125 Type
Test board material : glass epoxy-resin
Test board thickness : 1.0mm
NR10050 Type
Test board material : glass epoxy-resin
Test board thickness : 1.6mm