1.2x1.0mm Ceramic SMD Crystal CABS
DATASHEET
© Copyright 2019 Fox Electronics. All rights reserved
Title / Description: CABS SERIES STANDARD SPECIFICATIONS
Drawing Number: CABS-DOC-1 Size:
A
Part Number: Cage: 61429
Draftsperson: BEC Approved: MAJ Revision Date: 06/13/2019
Page 1 of 2
Tolerances down to ±10 PPM
Stabilities down to ±10 PPM
Temperature Ranges as wide as -40ºC to +85ºC
Frequency Range
(
MHz
)
Operating Mode Max ESR Ω
32.000 ~ 32.999999 Fundamental 100
33.000 ~ 36.999999 Fundamental 80
37.000 ~ 80.000 Fundamental 60
.
•Available Operating Temperatures and Stabilities*
Operating
Temperature ±10 PPM ±15 PPM ±20 PPM ±25 PPM
-20 ~+70ºC O O O O
-30 ~+85ºC X O O O
-40 ~+85ºC X O O O
Key: O=Available, X=Not Available
*Does not imply a stocked part.
• SPECIFICATIONS
PARAMETERS MAX
(unless otherwise noted)
Frequency Range 32.000 ~ 80.000 MHz
Frequency Tolerance @ 25ºC
(
See options on pa
g
e 2
)
Frequency Stability, ref @ 25ºC
(
See options below
)
Temperature Range
Operating (T
OPR
)
Storage (T
STG
)
(See options below)
-55ºC ~ +125ºC
Shunt Capacitance (C
O
) 2 pF
Load Capacitance (C
L
)
(
See options on pa
g
e 2
)
Drive Level 100
µ
W
(
10
µ
W t
yp
ical
)
Ag
in
g
p
er
y
ear ±3 PPM
Maximum Soldering Temp / Time 260ºC / 10 Seconds x 2
Moisture Sensitivity Level (MSL) 1
Termination Finish
A
u over Ni
Lead (Pb) Free Yes
RoHS/REACH Complian
t
Yes
Note: Dimensional drawing is for reference to critical specifications defined by size measurements.
Certain non-critical visual attributes, such as side castellations, etc. may vary.
1.2x1.0mm Ceramic SMD Crystal CABS
DATASHEET
© Copyright 2019 Fox Electronics. All rights reserved
Title / Description: CABS SERIES STANDARD SPECIFICATIONS
Drawing Number: CABS-DOC-1 Size:
A
Part Number: Cage: 61429
Draftsperson: BEC Approved: MAJ Revision Date: 06/13/2019
Page 2 of 2
• TAPE SPECIFICATIONS (millimeters) • REEL SPECIFICATIONS (millimeters)
A B C D E F Reel QTY G H I J K L M
1.5
4.0 4.0 3.5 8.0 0.45 -T3 = 3,000
-T5 = 5,000
2.0
13
21 60 180 9.0 1.5
Available
O
ptions
&
Part
I
dentification for CABS*
F CABS F F D M 40.0
F CABS F F D M 40.0
FOX
Model
Number
Tolerance
D = ±25 PPM
E = ±20 PPM
F = ±15 PPM
H = ±10 PPM
Stability
D = ±25 PPM
E = ±20 PPM
F = ±15 PPM
H = ±10 PPM
Load
Capacitance1
B = 6 pF
V = 7 pF
D = 8 pF
E = 10 pF
G = 12 pF
Operating
Temperature
F = -20 ~ +70ºC
K = -30 ~ +85ºC
M = -40 ~ +85°C
Frequency
(MHz)
*Not all frequency, tolerance, stability, load, and operating temperature combinations may be available.
1Listed load capacitances represent the most commonly used. Other load capacitances are available.
Corporate Headquarters
5570 Enterprise Parkway
Fort Myers, FL 33905
http://www.FOXONLINE.com
Sales
1-888-GET-2-FOX (1-888-438-2369) or
1-239-693-0099
http://www.FOXONLINE.com/repdisty
Tech Support
http://www.FOXONLINE.com/email
PRODUCT USE: Fox Electronics reserves the right to modify the products and/or specifications described herein at any time and at Fox Electronics' sole
discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance
specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way
when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied,
including, but not limited to, the suitability of Fox Electronics' products for any particular purpose, an implied warranty of merchantability, or non-infringement of
the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of Fox
Electronics or any third parties.
Fox Electronics' products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where
the failure or malfunction of a Fox Electronics product can be reasonably expected to significantly affect the health or safety of users. Anyone using a Fox
Electronics product in such a manner does so at their own risk, absent an express, written agreement by Fox Electronics.
Fox Electronics and the Fox logo are registered trademarks of Fox Electronics. Product specification is subject to change without notice. Other trademarks and
service marks used herein, including protected names, logos and designs, are the property of Fox Electronics or their respective third-party owners.
For datasheet type definitions and a glossary of common terms, visit http://www.foxonline.com/tgcrystals.html .
