General Description
The MAX5477/MAX5478/MAX5479 nonvolatile, dual,
linear-taper, digital potentiometers perform the function
of a mechanical potentiometer, but replace the
mechanics with a simple 2-wire digital interface. Each
device performs the same function as a discrete poten-
tiometer or variable resistor and has 256 tap points.
The devices feature an internal, nonvolatile EEPROM
used to store the wiper position for initialization during
power-up. A write-protect feature prevents accidental
overwrites of the EEPROM. The fast-mode I2C-compati-
ble serial interface allows communication at data rates
up to 400kbps, minimizing board space and reducing
interconnection complexity in many applications. Three
address inputs allow a total of eight unique address
combinations.
The MAX5477/MAX5478/MAX5479 provide three nomi-
nal resistance values: 10k(MAX5477), 50k
(MAX5478), or 100k(MAX5479). The nominal resistor
temperature coefficient is 70ppm/°C end-to-end and
10ppm/°C ratiometric. The low temperature coefficient
makes the devices ideal for applications requiring a low-
temperature-coefficient variable resistor, such as low-
drift, programmable gain-amplifier circuit configurations.
The MAX5477/MAX5478/MAX5479 are available in 16-
pin 3mm x 3mm x 0.8mm TQFN and 14-pin 4.4mm x
5mm TSSOP packages. These devices operate over
the extended -40°C to +85°C temperature range.
Applications
Mechanical Potentiometer Replacement
Low-Drift Programmable-Gain Amplifiers
Volume Control
Liquid-Crystal Display (LCD) Contrast Control
Features
oPower-On Recall of Wiper Position from
Nonvolatile Memory
oEEPROM Write Protection
oTiny 3mm x 3mm x 0.8mm Thin QFN Package
o70ppm/°C End-to-End Resistance Temperature
Coefficient
o10ppm/°C Ratiometric Temperature Coefficient
oFast 400kbps I2C-Compatible Serial Interface
o1µA (max) Static Supply Current
oSingle-Supply Operation: +2.7V to +5.25V
o256 Tap Positions per Potentiometer
o±0.5 LSB DNL in Voltage-Divider Mode
o±1 LSB INL in Voltage-Divider Mode
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile,
I2C-Interface, Digital Potentiometers
________________________________________________________________
Maxim Integrated Products
1
19-3379; Rev 5; 11/11
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Pin Configurations appear at end of data sheet.
EVALUATION KIT
AVAILABLE
Ordering Information/Selector Guide
PART TEMP RANGE PIN-PACKAGE END-TO-END
RESISTANCE (k)TOP MARK
MAX5477ETE+T -40°C to +8C 16 TQFN-EP* 10 ABO
MAX5477EUD+ -40°C to +85°C 14 TSSOP 10
MAX5478ETE+T -40°C to +8C 16 TQFN-EP* 50 ABP
MAX5478EUD+ -40°C to +85°C 14 TSSOP 50
MAX5479ETE+T -40°C to +8C 16 TQFN-EP* 100 ABQ
MAX5479EUD+ -40°C to +85°C 14 TSSOP 100
+
Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
*
EP = Exposed pad.
Functional Diagram
MAX5477
MAX5478
MAX5479
8-BIT
SHIFT
REGISTER
POR
16-BIT
LATCH
16-BIT
NV
MEMORY
SDA
SCL
WP
A0
A1
A2
8256
POSITION
DECODER
8
8
256
256
POSITION
DECODER
256
HA
WA
LA
HB
WB
LB
VDD
GND
I2C
INTERFACE
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VDD = +2.7V to +5.25V, H_ = VDD, L_ = GND, TA= -40°C to +85°C, unless otherwise noted. Typical values are at VDD = +5V,
TA= +25°C.) (Note 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
SDA, SCL, VDD to GND.........................................-0.3V to +6.0V
All Other Pins to GND.................................-0.3V to (VDD + 0.3V)
Maximum Continuous Current into H_, L_, and W_
MAX5477......................................................................±5.0mA
MAX5478......................................................................±1.3mA
MAX5479......................................................................±0.6mA
Continuous Power Dissipation (TA= +70°C)
16-Pin TQFN (derate 17.5mW/°C above +70°C) .......1398mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) .........727mW
Operating Temperature Range ...........................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
PACKAGE THERMAL CHARACTERISTICS (Note 1)
TQFN
Junction-to-Ambient Thermal Resistance (θJA) ........57.2°C/W
Junction-to-Case Thermal Resistance (θJC) ................40°C/W
TSSOP
Junction-to-Ambient Thermal Resistance (θJA) ......100.4°C/W
Junction-to-Case Thermal Resistance (θJC) ................30°C/W
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC PERFORMANCE (VOLTAGE-DIVIDER MODE)
Resolution 256 Taps
Integral Nonlinearity INL (Note 3) ±1 LSB
Differential Nonlinearity DNL (Note 3) ±0.5 LSB
Dual Code Matching R0 and R1 set to same code (all codes) ±1 LSB
End-to-End Resistance
Temperature Coefficient TCR 70 ppm/°C
Ratiometric Resistance
Temperature Coefficient 10 ppm/°C
MAX5477 -4
MAX5478 -0.6
Full-Scale Error
MAX5479 -0.3
LSB
MAX5477 4
MAX5478 0.6
Zero-Scale Error
MAX5479 0.3
LSB
DC PERFORMANCE (VARIABLE-RESISTOR MODE)
VDD = 3V ±3
Integral Nonlinearity (Note 4) INL VDD = 5V ±1.5 LSB
MAX5477 ±1
MAX5478 ±1
Differential Nonlinearity (Note 4) DNL
MAX5479 ±1
LSB
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(VDD = +2.7V to +5.25V, H_ = VDD, L_ = GND, TA= -40°C to +85°C, unless otherwise noted. Typical values are at VDD = +5V,
TA= +25°C.) (Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Dual Code Matching R0 and R1 set to same code
(all codes), VDD = 3V or 5V ±3 LSB
DC PERFORMANCE (RESISTOR CHARACTERISTICS)
Wiper Resistance RW(Note 5) 325 675
Wiper Capacitance CW 10 pF
MAX5477 7.5 10 12.5
MAX5478 37.5 50 62.5
End-to-End Resistance RHL
MAX5479 75 100 125
k
DIGITAL INPUTS
VDD = 3.4V to 5.25V 2.4
Input High Voltage (Note 6) VIH VDD < 3.4V 0.7 x VDD V
Input Low Voltage VIL (Note 6) 0.8 V
Output Low Voltage VOL I
SINK = 3mA 0.4 V
WP Pullup Resistance IWP 255 k
Input Leakage Current ILEAK ±1 µA
Input Capacitance 5 pF
DYNAMIC CHARACTERISTICS
Crosstalk
HA = 1kHz (0 to VDD), LA = GND,
LB = GND, measure WB -75 dB
MAX5477 400
MAX5478 100
3dB Bandwidth (Note 7)
MAX5479 50
kHz
Total Harmonic Distortion Plus
Noise THD+N H_ = 1VRMS, f = 1kHz, L_ = GND,
measure W_ 0.003 %
NONVOLATILE MEMORY RELIABILITY
Data Retention TA = +85°C 50 Years
TA = +2C 200,000
Endurance
TA = +85°C 50,000 Stores
POWER SUPPLY
Power-Supply Voltage VDD 2.70 5.25 V
Writing to EEPROM, digital inputs at
GND or VDD, TA = +25°C (Note 8) 250 400
WP = GND 15 20.6
Supply Current IDD Normal operation,
digital inputs at GND or
VDD, TA = +25°C WP = VDD 0.5 1
µA
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
4 _______________________________________________________________________________________
Note 2: All devices are production tested at TA= +25°C and are guaranteed by design and characterization for -40°C < TA< +85°C.
Note 3: The DNL and INL are measured with the potentiometer configured as a voltage-divider with H_ = VDD and L_ = GND. The
wiper terminal is unloaded and measured with a high-input-impedance voltmeter.
Note 4: The DNL and INL are measured with the potentiometer configured as a variable resistor. H_ is unconnected and L_ =
GND. For VDD = +5V, the wiper is driven with 400µA (MAX5477), 80µA (MAX5478), or 40µA (MAX5479). For VDD = +3V,
the wiper is driven with 200µA (MAX5477), 40µA (MAX5478), or 20µA (MAX5479).
Note 5: The wiper resistance is measured using the source currents given in Note 3.
Note 6: The devices draw current in excess of the specified supply current when the digital inputs are driven with voltages between
(VDD - 0.5V) and (GND + 0.5V). See Supply Current vs. Digital Input Voltage in the
Typical Operating Characteristics
.
Note 7: Wiper at midscale with a 10pF load (DC measurement). L_ = GND, an AC source is applied to H_, and the W_ output is
measured. A 3dB bandwidth occurs when the AC W_/H_ value is 3dB lower than the DC W_/H_ value.
Note 8: The programming current exists only during power-up and EEPROM writes.
Note 9: The SCL clock period includes rise and fall times (tR= tF). All digital input signals are specified with tR= tF= 2ns and
timed from a voltage level of (VIL + VIH) / 2.
Note 10: Digital timing is guaranteed by design and characterization, and is not production tested.
Note 11: This is measured from the STOP pulse to the time it takes the output to reach 50% of the output step size (divider mode). It
is measured with a maximum external capacitive load of 10pF.
Note 12: An appropriate bus pullup resistance must be selected depending on board capacitance. Refer to the I2C-bus specifica-
tion document linked to this web address: www.semiconductors.philips.com/acrobat/literature/9398/39340011.pdf
Note 13: The idle time begins from the initiation of the STOP pulse.
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
ANALOG SECTION
MAX5477 325
MAX5478 500
Wiper Settling Time (Note 11) tWS
MAX5479 1000
ns
DIGITAL SECTION
SCL Clock Frequency fSCL 400 kHz
Setup Time for START Condition tSU:STA 0.6 µs
Hold Time for START Condition tHD:STA 0.6 µs
SCL High Time tHIGH 0.6 µs
SCL Low Time tLOW 1.3 µs
Data Setup Time tSU:DAT 100 ns
Data Hold Time tHD:DAT 0 0.9 µs
SDA, SCL Rise Time tR 300 ns
SDA, SCL Fall Time tF 300 ns
Setup Time for STOP Condition tSU:STO 0.6 µs
Bus Free Time Between STOP and
START Condition tBUF Minimum power-up rate = 0.2V/µs 1.3 µs
Pulse Width of Spike Suppressed tSP 50 ns
Capacitive Load for Each Bus Line CB(Note 12) 400 pF
Write NV Register Busy Time (Note 13) 12 ms
TIMING CHARACTERISTICS
(VDD = +2.7V to +5.25V, H_ = VDD, L_ = GND, TA= -40°C to +85°C, unless otherwise noted. Typical values are at VDD = +5V,
TA= +25°C. See Figure 1.) (Notes 9 and 10)
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
_______________________________________________________________________________________
5
0
0.2
0.6
0.4
0.8
1.0
-40 10-15 35 60 85
SUPPLY CURRENT
vs. TEMPERATURE (MAX5477)
MAX5477/78/79 toc01
TEMPERATURE (°C)
SUPPLY CURRENT (µA)
VCC = 5V
WP = VDD
VCC = 3V
5
7
11
9
13
15
-40 10-15 35 60 85
SUPPLY CURRENT
vs. TEMPERATURE
MAX5477/78/79 toc1a
TEMPERATURE (°C)
SUPPLY CURRENT (µA)
VCC = 5V
WP = GND
VCC = 3V
0
100
50
200
150
300
250
350
450
400
500
0649632 128 160 192 224 256
WIPER RESISTANCE
vs. INPUT CODE
MAX5477/78/79 toc02
INPUT CODE
WIPER RESISTANCE ()
200ns/div
TAP-TO-TAP SWITCHING TRANSIENT
SDA
2V/div
W_
50mV/div
MAX5477/78/79 toc03
MAX5477
CL = 10pF
H_ = VDD
FROM TAP 00 TO TAP 04
TAP-TO-TAP SWITCHING TRANSIENT
MAX5477/78/79 toc04
1µs/div
SDA
2V/div
W_
20mV/div
MAX5478
CL = 10pF
H_ = VDD
FROM TAP 00 TO TAP 04
TAP-TO-TAP SWITCHING TRANSIENT
MAX5477/78/79 toc05
400ns/div
SDA
2V/div
W_
20mV/div
MAX5479
CW_ = 10pF
H_ = VDD
FROM TAP 00 TO TAP 04
2µs/div
WIPER TRANSIENT AT POWER-ON
VDD
2V/div
W_
1V/div
MAX5477/78/79 toc06
MAX5477
TAP = 128
WIPER TRANSIENT AT POWER-ON
MAX5477/78/79 toc07
4µs/div
VDD
2V/div
W_
1V/div
MAX5478
TAP = 128
WIPER TRANSIENT AT POWER-ON
MAX5477/78/79 toc08
2µs/div
VDD
2V/div
W_
1V/div
MAX5479
TAP = 128
Typical Operating Characteristics
(VDD = +5V, H_ = VDD, L_ = GND, TA= +25°C, unless otherwise noted.)
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
6 _______________________________________________________________________________________
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
06432 96 128 160 192 224 256
DIFFERENTIAL NONLINEARITY
vs. CODE (VDM MODE)
MAX5477/78/79 toc10
CODE
DNL (LSB)
MAX5477
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
06432 96 128 160 192 224 256
INTEGRAL NONLINEARITY
vs. CODE (VDM MODE)
MAX5477/78/79 toc11
CODE
INL (LSB)
MAX5478
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
06432 96 128 160 192 224 256
DIFFERENTIAL NONLINEARITY
vs. CODE (VDM MODE)
MAX5477/78/79 toc12
CODE
DNL (LSB)
MAX5478
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
06432 96 128 160 192 224 256
INTEGRAL NONLINEARITY
vs. CODE (VRM MODE)
MAX5477/78/79 toc13
CODE
INL (LSB)
MAX5478
-0.10
-0.08
-0.04
0
0.02
0.06
0.10
06432 96 128 160 192 224 256
DIFFERENTIAL NONLINEARITY
vs. CODE (VRM MODE)
MAX5477/78/79 toc14
CODE
DNL (LSB)
-0.06
-0.02
0.08
0.04
MAX5478
-0.20
-0.12
-0.16
-0.04
-0.08
0.04
0
0.08
0.16
0.12
0.20
0649632 128 160 192 224 256
INTEGRAL NONLINEARITY
vs. CODE (VDM MODE)
MAX5477/78/79 toc15
CODE
INL (LSB)
MAX5479
-0.14
-0.02
-0.04
-0.06
-0.08
-0.10
-0.12
0
0.04
0.02
0.10
0.08
0.12
0.06
0.14
06432 96 128 160 192 224 256
DIFFERENTIAL NONLINEARITY
vs. CODE (VDM MODE)
MAX5477/78/79 toc16
CODE
DNL (LSB)
MAX5479
-0.20
-0.12
-0.16
-0.04
-0.08
0.04
0
0.08
0.16
0.12
0.20
0649632 128 160 192 224 256
INTEGRAL NONLINEARITY
vs. CODE (VRM MODE)
MAX5477/78/79 toc17
CODE
INL (LSB)
MAX5479
Typical Operating Characteristics (continued)
(VDD = +5V, H_ = VDD, L_ = GND, TA= +25°C, unless otherwise noted.)
0
0.05
0.15
0.10
0.25
0.30
0.20
0.35
0649632 128 160 192 224 256
INTEGRAL NONLINEARITY
vs. CODE (VDM MODE)
MAX5477/78/79 toc09
CODE
INL (LSB)
MAX5477
MAX5477/MAX5478/MAX5479
CROSSTALK vs.
FREQUENCY (MAX5478)
MAX5477/78/79 toc20
FREQUENCY (kHz)
CROSSTALK (dB)
1001010.1
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
-100
0.01 1000
CW_ = 10pF
CROSSTALK vs.
FREQUENCY (MAX5479)
MAX5477/78/79 toc21
FREQUENCY (kHz)
CROSSTALK (dB)
1000100101
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
-100
0.1 10,000
CW_ = 10pF
FREQUENCY (kHz)
GAIN (dB)
MIDSCALE WIPER RESPONSE
vs. FREQUENCY (MAX5477)
1
0
-1
-2
-3
-4
-5
-6
-7
-8
10.1 10 100 1000
MAX5477/78/79 toc22
CW_ = 10pF
CW_ = 50pF
MIDSCALE WIPER RESPONSE
vs. FREQUENCY (MAX5478)
MAX5477 toc23
FREQUENCY (kHz)
GAIN (dB)
100101
-7
-6
-5
-4
-3
-2
-1
0
1
2
-8
0.1 1000
CW_ = 50pF
CW_ = 10pF
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (MAX5478)
MAX5477/78/79 toc26
FREQUENCY (kHz)
THD+N (%)
1010.1
0.001
0.01
0.1
1
10
0.0001
0.01 100
MIDSCALE
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
_______________________________________________________________________________________
7
-0.20
-0.12
-0.16
-0.04
-0.08
0.04
0
0.08
0.16
0.12
0.20
0649632 128 160 192 224 256
DIFFERENTIAL NONLINEARITY
vs. CODE (VRM MODE)
MAX5477/78/79 toc18
CODE
DNL (LSB)
MAX5479
FREQUENCY (kHz)
CROSSTALK (dB)
CROSSTALK vs.
FREQUENCY (MAX5477)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
0.1 1 10 100 1000 10,000
MAX5477/78/79 toc19
CW_ = 10pF
MIDSCALE WIPER RESPONSE
vs. FREQUENCY (MAX5479)
MAX5477/78/79 toc24
FREQUENCY (kHz)
GAIN (dB)
100101
-4
-3
-2
-1
0
1
2
-5
0.1 1000
CW_ = 50pF
CW_ = 10pF
FREQUENCY (kHz)
THD+N (%)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (MAX5477)
1
0.1
0.01
0.001
0.01 0.1 1 10 100
MAX5477/78/79 toc25
MIDSCALE
Typical Operating Characteristics (continued)
(VDD = +5V, H_ = VDD, L_ = GND, TA= +25°C, unless otherwise noted.)
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
8 _______________________________________________________________________________________
Typical Operating Characteristics (continued)
(VDD = +5V, H_ = VDD, L_ = GND, TA= +25°C, unless otherwise noted.)
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY (MAX5479)
MAX5477/78/79 toc27
FREQUENCY (kHz)
THD+N (%)
1010.1
0.001
0.01
0.1
1
10
0.0001
0.01 100
MIDSCALE
-0.6
-0.2
-0.4
0.2
0
0.4
0.6
-40 85
END-TO-END RESISTANCE % CHANGE
vs. TEMPERATURE (MAX5477)
MAX5477/78/79 toc28
TEMPERATURE (°C)
END-TO-END RESISTANCE CHANGE (%)
10-15 35 60
-0.5
-0.2
-0.3
-0.4
-0.1
0
0.1
0.2
0.3
0.4
0.5
-40 10-15 35 60 85
END-TO-END RESISTANCE % CHANGE
vs. TEMPERATURE (MAX5478)
MAX5477/78/79 toc29
TEMPERATURE (°C)
END-TO-END RESISTANCE CHANGE (%)
-0.5
-0.2
-0.3
-0.4
-0.1
0
0.1
0.2
0.3
0.4
0.5
-40 10-15 35 60 85
END-TO-END RESISTANCE % CHANGE
vs. TEMPERATURE (MAX5479)
MAX5477/78/79 toc30
TEMPERATURE (°C)
END-TO-END RESISTANCE CHANGE (%)
0
350
300
250
400
450
550
500
600
0 1.00.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
SUPPLY CURRENT
vs. DIGITAL INPUT VOLTAGE
MAX5477/78/79 toc31
DIGITAL INPUT VOLTAGE (V)
SUPPLY CURRENT (µA)
WP = GND
VCC = 5V
VCC = 3V
200
150
100
50
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
_______________________________________________________________________________________ 9
Pin Description
PIN
TSSOP THIN QFN NAME FUNCTION
1 15 HA Potentiometer A High Terminal
2 14 WA Potentiometer A Wiper Terminal
3 13 LA Potentiometer A Low Terminal
4 12 HB Potentiometer B High Terminal
5 11 WB Potentiometer B Wiper Terminal
6 10 LB Potentiometer B Low Terminal
79WP
Write-Protect Input. Connect to GND to allow changes to the wiper position and the data stored
in the EEPROM. Connect to VDD or leave unconnected to enable the write protection of the
EEPROM. See the Write Protect (WP) section for operating instructions.
8 7 GND Ground
9 6 A2 Address Input 2. Connect to VDD or GND (see Table 1).
10 5 A1 Address Input 1. Connect to VDD or GND (see Table 1).
11 4 A0 Address Input 0. Connect to VDD or GND (see Table 1).
12 3 SDA I2C Serial Data
13 2 SCL I2C Clock Input
14 1 VDD Power-Supply Input. Connect a +2.7V to +5.25V power supply to VDD and bypass VDD to GND
with a 0.1µF capacitor installed as close to the device as possible.
8, 16 N.C. No Connection. Do not connect.
EP EP Exposed Paddle. Do not connect.
SDA
SCL
START
CONDITION
(S)
tHD:STA
tRtF
tHIGH
tLOW
tSU:DAT
tHD:DAT
REPEATED START
CONDITION
(SR)
tHD:STA
tSU:STA
tSU:STO
tBUF
STOP
CONDITION
(P)
START
CONDITION
(S)
ACKNOWLEDGE
(A)
PARAMETERS ARE MEASURED FROM 30% TO 70%.
Figure 1. I2C Serial-Interface Timing Diagram
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
10 ______________________________________________________________________________________
Detailed Description
The MAX5477/MAX5478/MAX5479 contain two resistor
arrays with 255 elements in each array. The MAX5477
has a total end-to-end resistance of 10k, the
MAX5478 has an end-to-end resistance of 50k, and
the MAX5479 has an end-to-end resistance of 100k.
The MAX5477/MAX5478/MAX5479 provide access to
the high, low, and wiper terminals for a standard volt-
age-divider configuration. Connect H_, L_, and W_ in
any desired configuration as long as their voltages
remain between GND and VDD.
A simple 2-wire I2C-compatible serial interface moves
the wiper among the 256 tap points (Figure 2). A non-
volatile memory stores the wiper position and recalls
the stored wiper position upon power-up. The non-
volatile memory is guaranteed for 50 years for wiper
data retention and up to 200,000 wiper store cycles.
Analog Circuitry
The MAX5477/MAX5478/MAX5479 consist of two resistor
arrays with 255 resistive elements; 256 tap points are
accessible to the wipers, along the resistor string
between H_ and L_. The wiper tap point is selected by
programming the potentiometer through the I2C inter-
face. An address byte, a command byte, and 8 data bits
program the wiper position for each potentiometer. The
H_ and L_ terminals of the MAX5477/MAX5478/
MAX5479 are similar to the two end terminals of a
mechanical potentiometer. The MAX5477/MAX5478/
MAX5479 feature power-on reset circuitry that loads the
wiper position from the nonvolatile memory at power-up.
256-POSITION
DECODER
H_
L_
R255
S255
S254
S3
S2
S1
S256
R254
R2
R1
W_
RW
WIPER
CODE 02h
Figure 2. Potentiometer Configuration
ADDRESS INPUTS
A2 A1 A0 SLAVE ADDRESS
GND GND GND 0101000
GND GND VDD 0101001
GND VDD GND 0101010
GND VDD VDD 0101011
VDD GND GND 0101100
VDD GND VDD 0101101
VDD VDD GND 0101110
VDD VDD VDD 0101111
Table 1. Slave Addresses
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
______________________________________________________________________________________ 11
Digital Interface
The MAX5477/MAX5478/MAX5479 feature an internal,
nonvolatile EEPROM that stores the wiper state for ini-
tialization during power-up. The shift register decodes
the command and address bytes, routing the data to
the proper memory registers. Data written to a volatile
memory register immediately updates the wiper posi-
tion, or writes data to a nonvolatile register for storage
(see Table 3).
The volatile register retains data as long as the device
is powered. Removing power clears the volatile regis-
ter. The nonvolatile register retains data even after
power is removed. Upon power-up, the power-on reset
circuitry controls the transfer of data from the non-
volatile register to the volatile register.
Write Protect (WP)
A write-protect feature prevents accidental overwriting of
the EEPROM. Connect WP to VDD or leave unconnected
to prevent any EEPROM write cycles. Writing to the
volatile register (VREG) while WP = 1 updates the wiper
position with the protected data stored in the nonvolatile
register (NVREG). Connect WP to GND to allow write
commands to the EEPROM and to update the wiper
position from either the value in the EEPROM or directly
from the I2C interface (Table 2). Connecting WP to GND
increases the supply current by 19.6µA (max).
To ensure a fail-safe, write-protect feature, write the
data to be protected to both the nonvolatile and volatile
registers before pulling WP high. Releasing WP (WP =
0) and sending partial or invalid I2C commands (such
as single-byte address polling) can load the volatile
ADDRESS BYTE COMMAND BYTE DATA BYTE
1 2 3 4 5 6 7 8 9 1011121314151617 18 1920212223242526 27
SCL CYCLE
NUMBER
START
(S) A6 A5 A4 A3 A2 A1 A0 ACK
(A) TX NV V R3 R2 R1 R0 ACK
(A) D7 D6 D5 D4 D3 D2 D1 D0 ACK
(A)
STOP
(P)
NOTES
VREG 0101A2A1A00 00010001 D7D6D5D4D3D2D1D0
NVREG 0101A2A1A00 00100001 D7D6D5D4D3D2D1D0
NVREGxVREG 0101A2A1A00 01100001 D7D6D5D4D3D2D1D0
VREGxNVREG 0101A2A1A00 01010001 D7D6D5D4D3D2D1D0
WIPER A
ONLY
VREG 0101A2A1A00 00010010 D7D6D5D4D3D2D1D0
NVREG 0101A2A1A00 00100010 D7D6D5D4D3D2D1D0
NVREGxVREG 0101A2A1A00 01100010 D7D6D5D4D3D2D1D0
VREGxNVREG 0101A2A1A00 01010010 D7D6D5D4D3D2D1D0
WIPER B
ONLY
VREG 0101A2A1A00 00010011 D7D6D5D4D3D2D1D0
NVREG 0101A2A1A00 00100011 D7D6D5D4D3D2D1D0
NVREGxVREG 0101A2A1A00 01100011 D7D6D5D4D3D2D1D0
VREGxNVREG 0101A2A1A00 01010011 D7D6D5D4D3D2D1D0
WIPERS
A AND B
Table 3. Command Byte Summary
COMMAND WP = 0 WP = 1
Write to VREG
I2C data is written to VREG.
Wiper position updates with I2C data.
No change to NVREG.
Copy NVREG to VREG.
Wiper position updates with NVREG data.
No change to NVREG.
Write to NVREG No change to VREG or wiper position.
I2C data is written to NVREG.
No change to VREG or wiper position.
No change to NVREG.
Copy NVREG to VREG
Copy NVREG to VREG.
Wiper position updates with NVREG data.
No change to NVREG.
Copy NVREG to VREG.
Wiper position updates with NVREG data.
No change to NVREG.
Copy VREG to NVREG Copy VREG to NVREG.
No change to VREG or wiper position.
No change to VREG or wiper position.
No change to NVREG.
Table 2. Write-Protect Behavior of VREG and NVREG
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
12 ______________________________________________________________________________________
register with input shift register data and change the
wiper position. Use valid 3-byte I2C commands for
proper operation. This precautionary operation is nec-
essary only when transitioning from write protected
(WP = 1) to not write protected (WP = 0).
Serial Addressing
The MAX5477/MAX5478/MAX5479 operate as slave
devices that send and receive data through an I2C-/
SMBus™-compatible 2-wire serial interface. The inter-
face uses a serial data access (SDA) line and a serial
clock line (SCL) to achieve bidirectional communication
between master(s) and slave(s). A master, typically a
microcontroller, initiates all data transfers to the
MAX5477/MAX5478/MAX5479, and generates the SCL
clock that synchronizes the data transfer (Figure 1).
The MAX5477/MAX5478/MAX5479 SDA line operates
as both an input and an open-drain output. The SDA
line requires a pullup resistor, typically 4.7k. The
MAX5477/MAX5478/MAX5479 SCL line operates only
as an input. The SCL line requires a pullup resistor (typ-
ically 4.7k) if there are multiple masters on the 2-wire
interface, or if the master in a single-master system has
an open-drain SCL output. SCL and SDA should not
exceed VDD in a mixed-voltage system, despite the
open-drain drivers.
Each transmission consists of a START (S) condition
(Figure 3) sent by a master, followed by the
MAX5477/MAX5478/MAX5479 7-bit slave address plus
the NOP/Wbit (Figure 4), 1 command byte and 1 data
byte, and finally a STOP (P) condition (Figure 3).
START and STOP Conditions
Both SCL and SDA remain high when the interface is
not busy. A master controller signals the beginning of a
transmission with a START condition by transitioning
SDA from high to low while SCL is high. The master
controller issues a STOP condition by transitioning the
SDA from low to high while SCL is high, when it finishes
communicating with the slave. The bus is then free for
another transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on the SDA line must remain stable while SCL
is high (Figure 5).
Acknowledge
The acknowledge bit is a clocked 9th bit that the recipient
uses to handshake receipt of each byte of data (Figure
6). Thus, each byte transferred effectively requires 9 bits.
The master controller generates the 9th clock pulse, and
the recipient pulls down SDA during the acknowledge
clock pulse, so the SDA line remains stable low during
the high period of the clock pulse.
Slave Address
The MAX5477/MAX5478/MAX5479 have a 7-bit-long
slave address (Figure 4). The 8th bit following the 7-bit
slave address is the NOP/Wbit. Set the NOP/Wbit low for
a write command and high for a no-operation command.
The MAX5477/MAX5478/MAX5479 provide three
address inputs (A0, A1, and A2), allowing up to eight
devices to share a common bus (Table 1). The first 4
bits (MSBs) of the MAX5477/MAX5478/MAX5479 slave
addresses are always 0101. A2, A1, and A0 set the next
SDA
SCL S
START
CONDITION
P
STOP
CONDITION
Figure 3. START and STOP Conditions
MSBSTART
SCL
SDA ACKA0A2 A11010
LSB
NOP/W
Figure 4. Slave Address
SMBus is a trademark of Intel Corporation.
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
______________________________________________________________________________________ 13
3 bits in the slave address. Connect each address input
to VDD or GND to set these 3 bits. Each device must
have a unique address to share a common bus.
Message Format for Writing
Write to the MAX5477/MAX5478/MAX5479 by transmit-
ting the device’s slave address with NOP/W(8th bit) set
to zero, followed by at least 1 byte of information
(Figure 7). The 1st byte of information is the command
byte. The bytes received after the command byte are
the data bytes. The 1st data byte goes into the internal
register of the MAX5477/MAX5478/MAX5479 as select-
ed by the command byte (Figure 8).
Command Byte
Use the command byte to select the source and desti-
nation of the wiper data (nonvolatile or volatile memory
registers) and swap data between nonvolatile and
volatile memory registers (see Table 3).
Command Descriptions
VREG: The data byte writes to the volatile memory reg-
ister and the wiper position updates with the data in the
volatile memory register.
NVREG: The data byte writes to the nonvolatile memory
register. The wiper position is unchanged.
NVREGxVREG: Data transfers from the nonvolatile
memory register to the volatile memory register (wiper
position updates).
SDA
DATA STABLE,
DATA VALID
CHANGE OF
DATA ALLOWED
SCL
Figure 5. Bit Transfer
1
SCL
START
CONDITION
SDA
289
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
Figure 6. Acknowledge
A
0SLAVE ADDRESS COMMAND BYTE DATA BYTE
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
NOP/W 1 BYTE
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
D15 D14 D13 D12 D11 D10 D9 D8 D1 D0D3 D2D5 D4D7 D6
HOW CONTROL BYTE AND DATA BYTE MAP INTO
MAX5477/MAX5478/MAX5479 REGISTERS
S AA P
S A0SLAVE ADDRESS COMMAND BYTE
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
NOP/W ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
D15 D14 D13 D12 D11 D10 D9 D8
COMMAND BYTE IS STORED ON RECEIPT OF STOP CONDITION
AP
Figure 7. Command Byte Received
Figure 8. Command and Single Data Byte Received
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
14 ______________________________________________________________________________________
VREGxNVREG: Data transfers from the volatile memory
register into the nonvolatile memory register.
Nonvolatile Memory
The internal EEPROM consists of a 16-bit nonvolatile
register that retains the value written to it prior to power
down. The nonvolatile register is programmed with the
midscale value at the factory. The nonvolatile memory
is guaranteed for 50 years for wiper position retention
and up to 200,000 wiper write cycles. A write-protect
feature prevents accidental overwriting of the EEPROM.
Connect WP to VDD or leave open to enable the write-
protect feature. The wiper position only updates with
the value in the EEPROM when WP = VDD. Connect WP
to GND to allow EEPROM write cycles and to update
the wiper position from nonvolatile memory or directly
from the I2C serial interface.
Power-Up
Upon power-up, the MAX5477/MAX5478/MAX5479
load the data stored in the nonvolatile memory register
into the volatile memory register, updating the wiper
position with the data stored in the nonvolatile memory
register. This initialization period takes 10µs.
Standby
The MAX5477/MAX5478/MAX5479 feature a low-power
standby mode. When the device is not being pro-
grammed, it enters into standby mode and supply cur-
rent drops to 500nA (typ).
Applications Information
The MAX5477/MAX5478/MAX5479 are ideal for circuits
requiring digitally controlled adjustable resistance,
such as LCD contrast control (where voltage biasing
adjusts the display contrast), or for programmable fil-
ters with adjustable gain and/or cutoff frequency.
Positive LCD Bias Control
Figures 9 and 10 show an application where the
MAX5477/MAX5478/MAX5479 provide an adjustable,
positive LCD bias voltage. The op amp provides buffer-
ing and gain to the resistor-divider network made by
the potentiometer (Figure 9) or by a fixed resistor and a
variable resistor (see Figure 10).
Programmable Filter
Figure 11 shows the MAX5477/MAX5478/MAX5479 in a
1st-order programmable application filter. Adjust the
gain of the filter with R2, and set the cutoff frequency
with R3. Use the following equations to calculate the
gain (A) and the -3dB cutoff frequency (fC):
Offset Voltage and Gain Adjustment
Connect the high and low terminals of one potentiome-
ter of a MAX5477 between the NULL inputs of a
MAX410 and the wiper to the op amp’s positive supply
to nullify the offset voltage over the operating tempera-
ture range. Install the other potentiometer in the feed-
back path to adjust the gain of the MAX410 (Figure 12).
Adjustable Voltage Reference
Figure 13 shows the MAX5477/MAX5478/MAX5479
used as the feedback resistors in multiple adjustable
voltage reference applications. Independently adjust
the output voltages of the MAX6160 parts from 1.23V to
VIN - 0.2V by changing the wiper positions of the
MAX5477/MAX5478/MAX5479.
AR
R
fRC
C
=+
=××
1
1
2
1
2
3
π
VOUT
30V
5V
W_
H_
L_
MAX5477
MAX5478
MAX5479 MAX480
VOUT
30V
5V
W_
H_
L_
MAX5477
MAX5478
MAX5479
MAX480
Figure 9. Positive LCD Bias Control Using a Voltage-Divider Figure 10. Positive LCD Bias Control Using a Variable Resistor
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
______________________________________________________________________________________ 15
MAX6160
IN
5V
OUT
ADJ
GND
HA
LA
WA
VOUT1 IN OUT
ADJ
GND
HB
LB
WB
VOUT2
1/2 MAX5477
1/2 MAX5478
1/2 MAX5479
MAX6160
1/2 MAX5477
1/2 MAX5478
1/2 MAX5479
FOR THE MAX5477
VOUT_ = 1.23V x 10k
R
FOR THE MAX5478
VOUT_ = 1.23V x 50k
R
FOR THE MAX5479
VOUT_ = 1.23V x 100k
R
WHERE R = RHL x D / 256
AND D = DECIMAL VALUE OF WIPER CODE
RR
Figure 13. Adjustable Voltage Reference
3
2
5V
7
4
1
6
8
MAX410
HA LA
WA
R2
R1
HB
LB
WB
1/2 MAX5477
1/2 MAX5477
R2 = RHL x D / 256
WHERE RHL = END-TO-END RESISTANCE
AND = D DECIMAL VALUE OF WIPER CODE
Figure 12. Offset Voltage Adjustment Circuit
MAX5477
MAX5478
MAX5479
VIN
R2
HB
WB
LB
R1
VOUT
R3
HA
WA
LA
CMAX410
V+
V-
R2, R3 = RHL x D / 256
WHERE RHL = END-TO-END RESISTANCE
AND D = DECIMAL VALUE OF WIPER CODE
Figure 11. Programmable Filter
16
1
2
3
4
12
11
10
9
15 14 13
5678
N.C. HA WA LA
HB
WB
LB
WP
SCL
SDA
A0
A1 A2 GND N.C.
VDD
TOP VIEW
MAX5477
MAX5478
MAX5479
14
13
12
11
10
9
8
1
2
3
4
5
6
7
VDD
SCL
SDA
A0HB
LA
WA
HA
A1
A2
GNDWP
LB
WB
TSSOP
(4.4mm x 5mm)
THIN QFN
(3mm x 3mm)
MAX5477
MAX5478
MAX5479
++
Pin Configurations Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
16 TQFN-EP T1633F+3 21-0136 90-0033
14 TSSOP U14+1 21-0066 90-0113
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in
the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
16
____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 8/04 Initial release
4 1/09 Updated Ordering Information for lead-free information. 1
5 11/11 Released TQFN packages, revised Ordering Information. 1–4, 15, 16
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
MAX5477ETE+ MAX5479ETE+ MAX5477EUD+ MAX5478EUD+ MAX5479EUD+ MAX5477ETE+T
MAX5477EUD+T MAX5478ETE+ MAX5478ETE+T MAX5478EUD+T MAX5479ETE+T MAX5479EUD+T