FTR-K1 SERIES POWER RELAY 2 POLES - 5A LOW PROFILE TYPE FTR-F1 Series n FEATURES l l l l l l l Low profile (height: 16.5mm) DPST/DPDT 5A, TV-3 rating available High insulation (due to its reinforced insulation construction) Insulation Distance (between coil and contacts): 8mm min. Dielectric strength: 5KV Surge strength: 10KV Pin configuration compatible to VB UL, CSA, VDE, SEMKO, CQC recognized Plastic sealed, RT III RoHS Compliant Please see page 6 for more information n PARTNUMBER INFORMATION [Example] (a) FTR-F1 A (a) (b) Relay type A (c) 005 (d) V - RG (e) (f ) FTR-F1 : FTR-F1 Series (b) Contact configuration A C (c) Coil type / enclosure A D : 2 form A (SPST-NO) : 2 form C (d) Coil rated voltage 005 : 5....110VDC Coil rating table at page 3 (e) Contact material / TV type V T : Gold plate silver tin oxide (standard type) : Gold plate silver tin oxide (TV-3 rating type, only for 2 form A standard coil type) (f) Special type : Standard type : Transparent cover type Nil RG : Standard type (530mW) : High sensitivity type (400mW) Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-F1AA005V Actual marking: F1AA005V 1 FTR-K1SERIES SERIES FTR-F1 n SPECIFICATION Item Contact Data Life Standard Type F1 (A,C) A ( ) V TV-3 rating F1 AA ( ) T Sensitive Type F1 (A,C) D ( ) V Configuration 2 form A (DPST-NO) 2 form C 2 form A (DSDT-NO) 2 form A (DPST-NO) 2 form C (DPDT) Construction Single Material Gold plate silver tin oxide (AgSnO2) Resistance (initial) Max. 100mOhm at 1A, 6VDC Contact rating 5A, 250VAC / 24VDC Max. carrying current * 7A Max. switching voltage 400VAC/ 300VDC Max. switching power 1,250VA, 120W Min. switching load * 10mA, 5VDC Mechanical Min. 20 x 106 operations Electrical Coil Data Timing Data Insulation AC load Min. 100 x 103 operations DC load Min. 100 x 103 operations Lamp load (TV-3) - 25 x 103 operations min. - Rated Power (at 20 C) 530mW, 110V type: 550mW 400mW Operate Power (at 20 C) 260mW, 110V type: 270mW 225mW Operating temperature range -40 to +75 C (no frost) -40 to +70 C (transparent cover type, -RG) Operate (at nominal voltage) Max. 15ms (no diode, without bounce) Release (at nominal voltage) Max. 5ms (no diode, without bounce) Resistance (Initial) Min. 1,000MOhm at 500VDC Dielectric strength Open contacts 1,000VAC (50/60Hz) 1min. Coil and contacts 5,000VAC (50/60Hz) 1min. Adjacent contacts 3,000VAC (50/60Hz) 1 min. Surge strength Coil and contacts Clearance 8 mm Creepage EN61810-1, VDE0435 Other Vibration Resistance Shock 10.000V/ 1.2 x 50s standard wave 8 mm Voltage 250V Pollution degree 3 Material group IIIa Category C / 250V (reference voltage) (VDE0110b) Misoperation 10 to 55Hz double amplitude 1.65mm Endurance 10 to 55Hz double amplitude 3.3mm Misoperation Min. 100m/s (11 1ms) Endurance Min. 1000m/s (6 1ms) Weight Approximately 13 g Sealing Sealed RTIII * 1 When max. carrying current is more than 10A, PCB layout needs to be considered. * 2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1SERIES SERIES FTR-F1 n COIL RATING 530mW standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Max. Coil Voltage Voltage (VDC) (VDC) * 005 5 47 3.5 0.5 8.5 006 6 68 4.2 0.6 10.2 009 9 155 6.3 0.9 15.3 012 12 270 8.4 1.2 20.4 018 18 610 12.6 1.8 30.6 024 24 1,100 16.8 2.4 40.8 048 48 4,400 33.6 4.8 81.6 060 60 6,800 42 6 102 110 110 22,000 77 11 187 Rated Power (mW) 530 550 400mW high sensitive type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Max. Coil Voltage Voltage (VDC) (VDC) * 003 3 22.5 2.25 0.3 6 005 5 62 3.75 0.5 10 006 6 90 4.5 0.6 12 009 9 202 6.75 0.9 18 012 12 360 9 1.2 24 024 24 1,440 18 2.4 48 048 48 5,760 36 4.8 96 Rated Power (mW) 400 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. 3 FTR-K1SERIES SERIES FTR-F1 n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63614 CSA C22.2 No. 14 LR 40304 VDE 0435, 0631, 0700, 0860 40013858 SEMKO 5A, 24VDC (resistive) 5A, 250 VAC (resistive) 1/6 HP, 125VAC 1/4 HP, 250VAC Pilot duty: C300 Pilot duty: R300 (F1AA( )T, F1AA( )V) TV-3 (F1AA( )T) 5A, 250 VAC (cos=1) 2A, 250 VAC (cos=0.4) 5 A 24VDC (0ms), 85C EN 61058-1:1992 and A1 250VAC, 5 (1)A EN 61095:1993 and A1+A11 IEC60335-1 GWFI IEC 60695-2-12 >850C (except for -RG) GWIT IEC 60695-2-13 >775C(except for -RG) Complies with BSI, IMC, CQC n CHARACTERISTIC DATA 4 FTR-K1SERIES SERIES FTR-F1 n REFERENCE DATA n DIMENSIONS l Dimensions FTR-F1A type l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) FTR-F1C type Unit: mm 5 FTR-K1SERIES SERIES FTR-F1 RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1SERIES SERIES FTR-F1 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. December 23, 2010 7