1
FTR-K1 SERIES
n FEATURES
l Low prole (height: 16.5mm)
l DPST/DPDT 5A, TV-3 rating available
l High insulation
(due to its reinforced insulation construction)
Insulation Distance (between coil and contacts): 8mm min.
Dielectric strength: 5KV
Surge strength: 10KV
l Pin conguration compatible to VB
l UL, CSA, VDE, SEMKO, CQC recognized
l Plastic sealed, RT III
l RoHS Compliant
Please see page 6 for more information
Actual marking does not carry the type name : "FTR"
E.g.: Ordering code: FTR-F1AA005V Actual marking: F1AA005V
POWER RELAY
2 POLES - 5A LOW PROFILE TYPE
FTR-F1 Series
(a) Relay type FTR-F1 : FTR-F1 Series
(b) Contact conguration A : 2 form A (SPST-NO)
C : 2 form C
(c) Coil type / enclosure A : Standard type (530mW)
D : High sensitivity type (400mW)
(d) Coil rated voltage 005 : 5....110VDC
Coil rating table at page 3
(e) Contact material / TV type V : Gold plate silver tin oxide (standard type)
T : Gold plate silver tin oxide
(TV-3 rating type, only for 2 form A standard coil type)
(f) Special type Nil : Standard type
RG : Transparent cover type
n PARTNUMBER INFORMATION
FTR-F1 A A 005 V - RG
[Example] (a) (b) (c) (d) (e) (f)
2
FTR-K1 SERIES
n SPECIFICATION
Item Standard Type
F1 (A,C) A ( ) V
TV-3 rating
F1 AA ( ) T
Sensitive Type
F1 (A,C) D ( ) V
Contact
Data Conguration
2 form A
(DPST-NO)
2 form C
2 form A
(DSDT-NO)
2 form A
(DPST-NO)
2 form C (DPDT)
Construction Single
Material Gold plate silver tin oxide (AgSnO2)
Resistance (initial) Max. 100mOhm at 1A, 6VDC
Contact rating 5A, 250VAC / 24VDC
Max. carrying current *¹ 7A
Max. switching voltage 400VAC/ 300VDC
Max. switching power 1,250VA, 120W
Min. switching load *² 10mA, 5VDC
Life Mechanical Min. 20 x 106 operations
Electrical
AC load Min. 100 x 103 operations
DC load Min. 100 x 103 operations
Lamp load (TV-3) - 25 x 103
operations min. -
Coil Data Rated Power (at 20 ° C) 530mW, 110V type: 550mW 400mW
Operate Power (at 20 ° C) 260mW, 110V type: 270mW 225mW
Operating temperature range -40 to +75 °C (no frost)
-40 to +70 °C (transparent cover type, -RG)
Timing Data Operate (at nominal voltage) Max. 15ms (no diode, without bounce)
Release (at nominal voltage) Max. 5ms (no diode, without bounce)
Insulation Resistance (Initial) Min. 1,000MOhm at 500VDC
Dielectric strength
Open contacts 1,000VAC (50/60Hz) 1min.
Coil and contacts 5,000VAC (50/60Hz) 1min.
Adjacent contacts 3,000VAC (50/60Hz) 1 min.
Surge strength Coil and contacts 10.000V/ 1.2 x 50µs standard wave
Clearance 8 mm
Creepage 8 mm
EN61810-1, VDE0435 Voltage 250V
Pollution degree 3
Material group IIIa
Category C / 250V (reference voltage) (VDE0110b)
Other Vibration Resistance Misoperation 10 to 55Hz double amplitude 1.65mm
Endurance 10 to 55Hz double amplitude 3.3mm
Shock Misoperation Min. 100m/s² (11 ± 1ms)
Endurance Min. 1000m/s² (6 ± 1ms)
Weight Approximately 13 g
Sealing Sealed RTIII
FTR-F1 SERIES
* 1 When max. carrying current is more than 10A, PCB layout needs to be considered.
* 2 Minimum switching loads mentioned above are reference values. Please perform the conrmation test with actual
load before production since reference values may vary according to switching frequencies, environmental conditions
and expected reliability levels.
3
FTR-K1 SERIES
n COIL RATING
Coil
Code
Rated Coil
Voltage
(VDC)
Coil Resistance
+/- 10% (Ohm)
Must Operate
Voltage
(VDC) *
Must Release
Voltage
(VDC) *
Max. Coil Voltage
(VDC)
Rated Power
(mW)
005 5 47 3.5 0.5 8.5
530
006 6 68 4.2 0.6 10.2
009 9 155 6.3 0.9 15.3
012 12 270 8.4 1.2 20.4
018 18 610 12.6 1.8 30.6
024 24 1,100 16.8 2.4 40.8
048 48 4,400 33.6 4.8 81.6
060 60 6,800 42 6 102
110 110 22,000 77 11 187 550
FTR-F1 SERIES
530mW standard type
Coil
Code
Rated Coil
Voltage
(VDC)
Coil Resistance
+/- 10% (Ohm)
Must Operate
Voltage
(VDC) *
Must Release
Voltage
(VDC) *
Max. Coil Voltage
(VDC)
Rated Power
(mW)
003 3 22.5 2.25 0.3 6
400
005 5 62 3.75 0.5 10
006 6 90 4.5 0.6 12
009 9 202 6.75 0.9 18
012 12 360 9 1.2 24
024 24 1,440 18 2.4 48
048 48 5,760 36 4.8 96
400mW high sensitive type
Note: All values in the table are valid for 20°C and zero contact current.
* Specied operate values are valid for pulse wave voltage.
4
FTR-K1 SERIES
FTR-F1 SERIES
n CHARACTERISTIC DATA
FTR-F1 SERIES
Type Compliance Contact rating
UL UL 508
E63614
Flammability: UL 94-V0 (plastics)
5A, 24VDC (resistive)
5A, 250 VAC (resistive)
1/6 HP, 125VAC
1/4 HP, 250VAC
Pilot duty: C300
Pilot duty: R300 (F1AA( )T, F1AA( )V)
TV-3 (F1AA( )T)
CSA C22.2 No. 14
LR 40304
VDE 0435, 0631, 0700, 0860
40013858
5A, 250 VAC (cosφ=1)
2A, 250 VAC (cosφ=0.4)
5 A 24VDC (0ms), 85˚C
SEMKO EN 61058-1:1992 and A1
EN 61095:1993 and A1+A11
250VAC, 5 (1)A
IEC60335-1 GWFI IEC 60695-2-12 >850˚C (except for -RG)
GWIT IEC 60695-2-13 >775˚C(except for -RG)
n SAFETY STANDARDS
Complies with BSI, IMC, CQC
5
FTR-K1 SERIES
FTR-F1 SERIES
n REFERENCE DATA
n DIMENSIONS
l Dimensions l Schematics
(BOTTOM VIEW)
l PC board mounting
hole layout
(BOTTOM VIEW)
FTR-F1C type
Unit: mm
FTR-F1A type
6
FTR-K1 SERIES
1. General Information
l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC
including amendments.
l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005.
(Amendment to Directive 2002/95/EC)
l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes
at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf
l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specied.
This material has been veried to be compatible with PbSn assembly process.
2. Recommended Lead Free Solder Prole
l Recommended solder Sn-3.0Ag-0.5Cu.
RoHS Compliance and Lead Free Information
3. Moisture Sensitivity
l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.
4. Tin Whiskers
l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.
We highly recommend that you conrm your actual solder conditions
Flow Solder condition:
Pre-heating: maximum 120˚C
Soldering: dip within 5 sec. at
260˚C solder bath
Solder by Soldering Iron:
Soldering Iron
Temperature: maximum 360˚C
Duration: maximum 3 sec.
FTR-F1 SERIES
7
FTR-K1 SERIES
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: components@us.fujitsu.com
Web: http://us.fujitsu.com/components
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: emea.fujitsu.com/components/
Asia Pacic
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
Web: http://www.fujitsu.com/sg/services/micro/components/
Fujitsu Components International Headquarter Ofces
©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective
owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for gen-
eral information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen-
sive, complete and up to date.
Fujitsu Components Europe B.V. and afliated companies do however not accept any responsibility or liability on their behalf, nor on behalf
of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information
and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and afliated companies accept on their behalf, nor on behalf of its employees, any responsibility
or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or tness for
particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy,
comprehensiveness, usefulness, availability and completeness thereof. Rev. December 23, 2010
FTR-F1 SERIES
