www.vishay.com
61
MSM
Vishay Dale
Document Number: 31514
Revision 05-Aug-02 For Technical Questions, contact: ff2aresistors@vishay.com
TEST
Power Conditioning
Thermal Shock
Short Time Overload
Low Temperature Operation
Moisture Resistance
Resistance to Soldering Heat
Shock
Vibration
Load Life
Terminal Strength
Insulation Resistance
Dielectric Withstanding Voltage
CONDITIONS
1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100
hours ± 4 hours at + 25°C ambient temperature
5 cycles between - 65°C and + 125°C
2.5 x rated working voltage 5 seconds
45 minutes at full rated working voltage at - 65°C
240 hours with humidity ranging from 80% RH to 98% RH
Leads immersed in + 260°C solder to within 1/16" of body for 10 seconds
Total of 18 shocks at 100 G's
12 hours at maximum of 20 G's between 10 and 2,000 Hz
1000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour
“OFF” for full 1000 hour period
4 1/2 pound pull for 30 seconds
10,000 Megohm (minimum)
No evidence of arcing or damage (200 V RMS for 1 minute)
MAX. ∆R (Typical Test Lots)
± 0.50% ∆R
± 0.50% ∆R
± 0.25% ∆R (Characteristic K)
± 0.50% ∆R (Characteristic M)
± 0.25% ∆R (Characteristic K)
± 0.50% ∆R (Characteristic M)
± 0.50% ∆R
± 0.25% ∆R
± 0.25% ∆R
± 0.25% ∆R
± 0.50% ∆R (Characteristic K)
± 2.00% ∆R (Characteristic M)
± 0.25% ∆R
—
—
PERFORMANCE
01 Schematic
03 Schematic
05 Schematic
CIRCUIT APPLICATION
3, 4 or 5 isolated resistors
"A" Profile "C" Profile
MSM06A-03 (M8340107xxxxxxG) MSM06C-03 (M8340104xxxxxxG)
MSM08A-03 (M8340108xxxxxxG) MSM08C-03 (M8340105xxxxxxG)
MSM10A-03 (M8340109xxxxxxG) MSM10C-03 (M8340106xxxxxxG)
The MSM06A-03, MSM08A-03, MSM10A-03, MSM06C-03, MSM08C-03 and
MSM10C-03 molded single-in-line resistor networks provide the user with a choice
of 3, 4 or 5 nominally equal resistors. Each resistor is isolated from all others.
Commonly used in the following applications:
• "Wired OR" Pull-up • Long-Line Impedance Balance
• Power Driven Pull-up • LED Current Limiting
• Power Gate Pull-up • ECL Output Pull-down
• Line Termination • TTL Input Pull-down
1 2 3 n-1 n
R2
R1
1 2 3 4 n-1 n
5, 7 or 9 resistors with one pin common
"A" Profile "C" Profile
MSM06A-01 (M8340107xxxxxxC) MSM06C-01 (M8340104xxxxxxC)
MSM08A-01 (M8340108xxxxxxC) MSM08C-01 (M8340105xxxxxxC)
MSM10A-01 (M8340109xxxxxxC) MSM10C-01 (M8340106xxxxxxC)
The MSM06A-01, MSM08A-01, MSM10A-01, MSM06C-01, MSM08C-01 and
MSM10C-01 molded single-in-line resistor networks provide the user with a choice
of 5, 7 or 9 nominally equal resistors, each connected to a common pin (Pin No. 1).
Commonly used in the following applications:
• "Wired OR" Pull-up • Open Collector Pull-up
• Power Gate Pull-up • TTL Input Pull-down
• MOS/ROM Pull-up/Pull-down • TTL Unused Gate Pull-up
4, 6 or 8 isolated resistors
"A" Profile "C" Profile
MSM06A-05 (M8340107xxxxxxH) MSM06C-05 (M8340104xxxxxxH)
MSM08A-05 (M8340108xxxxxxH) MSM08C-05 (M8340105xxxxxxH)
MSM10A-05 (M8340109xxxxxxH) MSM10C-05 (M8340106xxxxxxH)
The MSM06A-05, MSM08A-05, MSM10A-05, MSM06C-05, MSM08C-05 and
MSM10C-05 molded single-in-line resistor networks provide the user with a choice
of 4, 6 or 8 pair of R1/R2 resistor values for pulse squaring and TTL dual-line
terminating requirements.
1 2 3 n-1 n
Thick Film Resistor Networks, Military, MIL-PRF-83401 - Type RZ