SP483E Enhanced Low EMI Half-Duplex RS-485 Transceiver * +5V Only * Low Power BiCMOS * Driver / Receiver Enable for Multi-Drop Configurations * Enhanced ESD Specifications: +/-15kV Human Body Model +/-15kV IEC61000-4-2 Air Discharge +/-8kV IEC61000-4-2 Contact Discharge * Low EMI Transceiver limited to 250kbps * Low Power 1A Shutdown Mode DESCRIPTION The SP483E is a half-duplex transceiver that meets the specifications of RS-485 and RS-422 serial protocols with enhanced ESD performance. The ESD tolerance has been improved on these devices to over +15kV for both Human Body Model and IEC61000-4-2 Air Discharge Method. This devices is pin-to-pin compatible with Exar's SP483 device as well as popular industry standards. As with the original versions, the SP483E feature Exar's BiCMOS design allowing low power operation without sacrificing performance. The SP483E is internally slew rate limited to reduce EMI and can meet the requirements of RS-485 and RS-422 up to 250kbps. The SP483E is also equipped with a low power shutdown mode. Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Output Voltages Logic.........................-0.3V to (Vcc + 0.5V) Drivers.............................................+/-15V Receivers..................-0.3V to (Vcc + 0.5V) Storage Temperature.......................-65C to +150C Power Dissipation..........................................500mW VCC.......................................................................+7V Input Voltages Logic.........................-0.3V to (Vcc + 0.5V) Drivers......................-0.3V to (Vcc + 0.5V) Receivers.........................................+/-15V ELECTRICAL CHARACTERISTICS TMIN to TMAX and VCC = +5.0V +/-5% unless otherwise noted. PARAMETERS MIN. TYP. MAX. UNITS CONDITIONS SP483E DRIVER DC Characteristics Differential Output Voltage GND Vcc Volts Unloaded; R = ; See Figure 1 Differential Output Voltage 2 Vcc Volts With Load; R = 50 (RS-422); See Figure 1 Differential Output Voltage 1.5 Vcc Volts With Load; R = 27 (RS-485); See Figure 1 Change in Magnitude of Driver Differential Output Voltage for Complimentary states 0.2 Volts R = 27 or R = 50; See Figure 1 Driver Common Mode Output Voltage 3 Volts R = 27 or R = 50; See Figure 1 Input High Voltage Volts Applies to DE, DI, RE Input Low Voltage 2.0 0.8 Volts Applies to DE, DI, RE Input Current, Driver Input 10 A Applies to DI Input Current, Control Lines 1 A Applies to DE, RE VOUT = HIGH +/-250 mA -7V VO +12V VOUT = LOW +/-250 mA -7V VO +12V Driver Short Circuit Current SP483E DRIVER AC Characteristics Max. Transmission Rate 250 Driver Input to Output, tPLH 250 800 Driver Input to Output, tPHL 250 Driver Skew Driver Rise or Fall Time 250 kbps RE = 5V, DE = 5V; RDIFF = 54, CL1 = CL2 = 100pF 2000 ns See Figures 3 & 5, RDIFF = 54, CL1 = CL2 = 100pF 800 2000 ns See Figures 3 & 5, RDIFF = 54, CL1 = CL2 = 100pF 100 800 ns See Figures 3 and 5, tSKEW = |tDPHL - tDPLH| 2000 ns From 10%-90%; RDIFF = 54 CL1 = CL2 = 100pF; See Figures 3 and 6 Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 ELECTRICAL CHARACTERISTICS TMIN to TMAX and VCC = +5.0V +/-5% unless otherwise noted. PARAMETERS MIN. TYP. MAX. UNITS CONDITIONS SP483E DRIVER (continued) AC Characteristics Driver Enable to Output High 250 2000 ns CL = 100pF, See Figures 4 and 6, S2 closed Driver Enable to Output Low 250 2000 ns CL = 100pF, See Figures 4 and 6, S1 closed Driver Disable Time from High 300 3000 ns CL = 15pF, See Figures 4 and 6, S2 closed Driver Disable Time from Low 300 3000 ns CL = 15pF, See Figures 4 and 6, S1 closed +0.2 Volts SP483E RECEIVER DC Characteristics Differential Input Threshold -0.2 Input Hysteresis 20 Output Voltage High mV 3.5 -7V VCM +12V VCM = 0V Volts IO = -4mA, VID = +200mV Output Voltage Low 0.4 Volts IO = +4mA, VID = +200mV Three-State ( High Impedance) Output Current +/-1 A 0.4V VO 2.4V; RE = 5V k -7V VCM +12V Input Current (A, B); VIN = 12V +1.0 mA DE = 0V, VCC = 0V or 5.25V, VIN = 12V Input Current (A, B); VIN = -7V -0.8 mA DE = 0V, VCC = 0V or 5.25V, VIN = -7V 95 mA 0V VO VCC Input Resistance 12 Short Circuit Current 15 7 SP483E RECEIVER AC Characteristics Max. Transmission Rate 250 kbps RE = 0V, DE = 0V Receiver Input to Output 250 2000 ns tPLH ; See Figures 3 & 7, RDIFF = 54, CL1 = CL2 = 100pF Receiver Input to Output 250 2000 ns tPHL ; See Figures 3 & 7, RDIFF = 54, CL1 = CL2 = 100pF ns RDIFF = 54, CL1 = CL2 = 100pF, See Figures 3 and 7 Differential Receiver Skew |tPHL - tPLH| 100 Receiver Enable to Output Low 45 70 ns CRL = 15pF, Figures 2 & 8; S1 Closed Receiver Enable to Output High 45 70 ns CRL = 15pF, Figures 2 & 8; S2 Closed Receiver Disable from LOW 45 70 ns CRL = 15pF, Figures 2 & 8; S1 Closed Receiver Disable from High 45 70 ns CRL = 15pF, Figures 2 & 8; S2 Closed Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 ELECTRICAL CHARACTERISTICS TMIN to TMAX and VCC = +5.0V +/-5% unless otherwise noted. PARAMETERS MIN. TYP. MAX. UNITS CONDITIONS 50 200 600 ns RE = 5V, DE = 0V Driver Enable from Shutdown to Output High 2000 ns CL = 100pF; See Figures 4 and 6; S2 Closed Driver Enable from Shutdown to Output Low 2000 ns CL = 100pF; See Figures 4 and 6; S1 Closed SP483E Shutdown Timing Time to Shutdown Receiver Enable from Shutdown to Output High 300 2500 ns CL = 15pF; See Figures 2 and 8; S2 Closed Receiver Enable from Shutdown to Output Low 300 2500 ns CL = 15pF; See Figures 2 and 8; S1 Closed +5.25 Volts POWER REQUIREMENTS Supply Voltage VCC +4.75 Supply Current No Load Shutdown Mode 900 A RE, DI = 0V or VCC; DE = VCC 600 A RE = 0V, DI = 0V or 5V; DE = 0V 10 A DE = 0V, RE = VCC 1 ENVIRONMENTAL AND MECHANICAL Operating Temperature Commercial (_C_) 0 70 C Industrial (_E_) -40 +85 C Storage Temperature -65 +150 C Package Plastic DIP (_P) NSOIC (_N) Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 PIN FUNCTION Pin 1 - RO - Receiver Output Pin 2 - RE - Receiver Output Enable Active LOW Pin 3 - DE - Driver Output Enable Active HIGH Pin 4 - DI - Driver Input Pin 5 - GND - Ground Connection Pin 6 - A - Driver Output / Receiver input Non-Inverting Pin 7 - B - Driver Output / Receiver Input Inverting Pin 8 - Vcc - Positive Supply 4.75V Vcc 5.25V Test Circuits A R VOD R 1k S2 B Figure 1. RS-485 Driver DC Test Load Circuit DI A B VCC S1 CRL VOC 1k Test Point Receiver Output CL1 A RDIFF Output Under Test RO B CL2 Figure 2. Receiver Timing Test Load Circuit 15pF VCC S1 500 CL S2 Figure 3. RS-485 Driver/Receiver Timing Test Figure 4. Driver Timing Test Load #2 Circuit f = 100kHz; t R 10ns; t F 10ns DRIVER INPUT +3V 1.5V 0V DRIVER OUTPUT B A 1.5V t PLH VO t PHL 1/2VO 1/2VO t DPLH DIFFERENTIAL VO+ 0V OUTPUT VA - VB VO- t DPHL tR tF t SKEW = |t DPLH - t DPHL | Figure 5. Driver Propagation Delays Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 Function Truth Tables INPUTS OUTPUTS INPUTS OUTPUTS RE DE DI LINE CONDITION RE DE A-B R X 1 1 No Fault 1 0 0 0 +0.2V 1 X 1 0 No Fault 0 1 0 0 -0.2V 0 X 0 X X Z Z 0 0 Inputs Open 1 X 1 X Fault Z Z 1 0 X Z A B Table 2. Receive Function Truth Table Table 1. Transmit Function Truth Table SWITCHING WAVEFORMS DE 1.5V 0V 1.5V t ZL 5V A, B A, B f = 100kHz; t R < 10ns; t F < 10ns +3V t LZ 2.3V VOL VOH 2.3V 0V Output normally LOW 0.5V Output normally HIGH 0.5V t ZH t HZ Figure 6. Driver Enable and Disable Times A- B f = 100kHz; t R 10ns ; t F 10ns 0V INPUT VOD2 + VOD2 - VOH R VOL 1.5V 1.5V OUTPUT t PHL 0V t PLH t SKEW = | t PHL- t PLH | Figure 7. Receiver Propagation Delays RE R +3V 0V 5V VIL f = 100kHz; t R 10ns; t F 10ns 1.5V 1.5V t ZL 1.5V VIH R 0V 1.5V t LZ Output normally LOW 0.5V Output normally HIGH 0.5V t ZH t HZ Figure 8. Receiver Enable and Disable Times Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 DESCRIPTION Receivers The SP483E is a half-duplex differential transceiver that meets the requirements of RS-485 and RS-422. Fabricated with an Exar proprietary BiCMOS process, this product requires a fraction of the power of older bipolar designs. The SP483E receivers have differential inputs with an input sensitivity as low as 200mV. Input impedance of the receivers is typically 15k (12k minimum). A wide common mode range of -7V to +12V allows for large ground potential differences between systems. The receivers have a tri-state enable control pin. A logic LOW on RE (pin 2) will enable the receiver, a logic HIGH on RE (pin 2) will disable the receiver. The RS-485 standard is ideal for multi-drop applications and for long-distance interfaces. RS-485 allows up to 32 drivers and 32 receivers to be connected to a data bus, making it an ideal choice for multi-drop applications. Since the cabling can be as long as 4,000 feet, RS-485 transceivers are equipped with a wide (-7V to +12V) common mode range to accommodate ground potential differences. Because RS-485 is a differential interface, data is virtually immune to noise in the transmission line. The SP483E receiver is rated for data rates up to 250kbps. The receivers are equipped with the fail-safe feature. Failsafe guarantees that the receiver output will be in a HIGH state when the input is left unconnected. Drivers Shutdown Mode The driver outputs of the SP483E are differential outputs meeting the RS-485 and RS-422 standards. The typical voltage output swing with no load will be 0 Volts to +5 Volts. With worst case loading of 54 across the differential outputs, the drivers can maintain greater than 1.5V voltage levels. The drivers have an enable control line which is active HIGH. A logic HIGH on DE (pin 3) will enable the differential driver outputs. A logic LOW on the DE (pin 3) will tri-state the driver outputs. The SP483E is equipped with a Shutdown mode. To enable the shutdown state, both driver and receiver must be disabled simultaneously. A logic LOW on DE (pin 3) and a Logic HIGH on RE (pin 2) will put the SP483E into Shutdown mode. In Shutdown, supply current will drop to typically 1A. ESD Tolerance The SP483E incorporates ruggedized ESD cells on all driver output and receiver input pins. The ESD structure is improved over our previous family for more rugged applications and environments sensitive to electro-static discharges and associated transients. The improved ESD tolerance is at least 15kV without damage or latch-up. The SP483E has internally slew rate limited driver outputs to minimize EMI. The maximum data rate for the SP483E drivers is 250kbps under load. There are different methods of ESD testing applied: a) MIL-STD-883, Method 3015.7 b) IEC61000-4-2 Air-Discharge c) IEC61000-4-2 Direct Contact Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 The Human Body Model has been the generally accepted ESD testing method for semiconductors. This method is also specified in MIL-STD-883, Method 3015.7 for ESD testing. The premise of this ESD test is to simulate the human body's potential to store electro-static energy and discharge it to an integrated circuit. The simulation is performed by using a test model as shown in Figure 9. This method will test the IC's capability to withstand an ESD transient during normal handling such as in manufacturing areas where the IC's tend to be handled frequently. The IEC61000-4-2, formerly IEC801-2, is generally used for testing ESD on equipment and systems. For system manufacturers, they must guarantee a certain amount of ESD protection since the system itself is exposed to the outside environment and human presence. The premise with IEC61000-4-2 is that the system is required to withstand an amount of static electricity when ESD is applied to points and surfaces of the equipment that are accessible to personnel during normal usage. The transceiver IC receives most of the ESD current when the ESD source is applied to the connector pins. The test circuit for IEC61000-4-2 is shown on Figure 10. There are two methods within IEC61000-4-2, the Air Discharge method and the Contact Discharge method. RS RC SW1 SW2 Device Under Test CS DC Power Source Figure 9. ESD Test Circuit for Human Body Model Contact-Discharge Model RS RC RV SW1 SW2 Device Under Test CS DC Power Source R S and RV add up to 330 for IEC61000-4-2. Figure 10. ESD Test Circuit for IEC61000-4-2 Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 I With the Air Discharge Method, an ESD voltage is applied to the equipment under test (EUT) through air. This simulates an electrically charged person ready to connect a cable onto the rear of the system only to find an unpleasant zap just before the person touches the back panel. The high energy potential on the person discharges through an arcing path to the rear panel of the system before he or she even touches the system. This energy, whether discharged directly or through air, is predominantly a function of the discharge current rather than the discharge voltage. Variables with an air discharge such as approach speed of the object carrying the ESD potential to the system and humidity will tend to change the discharge current. For example, the rise time of the discharge current varies with the approach speed. 30A 15A 0A t = 0ns The voltage stored in the capacitor is then applied through RS, the current limiting resistor, onto the device under test (DUT). In ESD tests, the SW2 switch is pulsed so that the device under test receives a duration of voltage. For the Human Body Model, the current limiting resistor (RS) and the source capacitor (CS) are 1.5k an 100pF, respectively. For IEC-61000-4-2, the current limiting resistor (RS) and the source capacitor (CS) are 330 an 150pF, respectively. The higher CS value and lower RS value in the IEC61000-4-2 model are more stringent than the Human Body Model. The larger storage capacitor injects a higher voltage to the test point when SW2 is switched on. The lower current limiting resistor increases the current charge onto the test point. The circuit model in Figures 9 and 10 represent the typical ESD testing circuit used for all three methods. The CS is initially charged with the DC power supply when the first switch (SW1) is on. Now that the capacitor is charged, the second switch (SW2) is on while SW1 switches off. Driver Outputs Receiver Inputs HUMAN BODY MODEL +/-15kV +/-15kV t = 30ns Figure 11. ESD Test Waveform for IEC61000-4-2 The Contact Discharge Method applies the ESD current directly to the EUT. This method was devised to reduce the unpredictability of the ESD arc. The discharge current rise time is constant since the energy is directly transferred without the air-gap arc. In situations such as hand held systems, the ESD charge can be directly discharged to the equipment from a person already holding the equipment. The current is transferred on to the keypad or the serial port of the equipment directly and then travels through the PCB and finally to the IC. Device Pin Tested t IEC61000-4-2 Air Discharge Direct Contact Level +/-15kV +/-15kV +/-8kV +/-8kV 4 4 Table 1. Transceiver ESD Tolerance levels Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com SP483E_100_020912 Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com 10 SP483E_100_020912 Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com 11 SP483E_100_020912 ORDERING INFORMATION Model Temperature Range Package Types SP483ECN-L........................................................................ 0C to +70C.................................................................................................8-pin NSOIC SP483ECN-L/TR.................................................................. 0C to +70C.................................................................................................8-pin NSOIC SP483EEN-L.................................................................... -40C to +85C...............................................................................................8-pin NSOIC SP483EEN-L/TR................................................................. -40C to +85C.............................................................................................8-pin NSOIC SP483ECP-L........................................................................ 0C to +70C....................................................................................................8-pin PDIP SP483EEP-L.................................................................... -40C to +85C...................................................................................................8-pin PDIP Note: /TR = Tape and Reel revision history DATE REVISION 2000 05 02/09/12 1.0.0 DESCRIPTION Legacy Sipex Datasheet Convert to Exar Format. Update ordering information. Change ESD specification to IEC61000-4-2. Notice EXAR Corporation reserves the right to make changes to any products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no representation that the circuits are free of patent infringement. Charts and schedules contained herein are only for illustration purposes and may vary depending upon a user's specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized ; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2012 EXAR Corporation Datasheet February 2012 Send your serial transceiver technical questions with technical details to: serialtechsupport@exar.com Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. Exar Corporation 48720 Kato Road, Fremont CA, 94538 * 510-668-7017 * www.exar.com 12 SP483E_100_020912