VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 FTDI Chip VA800A PROG Datasheet Programmer for VM800P Embedded Video Engine Plus module 1 Introduction The VA800A PROG is a programmer for the VM800P module. This provides a USB to SPI bridge that will enable access to the ATMEGA328P on the VM800P module. The module provides a suitable alternative to the inbuilt USB to UART programmer of the VM800P and may also be used to recover a damaged/corrupted MCU. 1.1 Features Connects to the VM800P Plus module using the SPI interface Micro-B USB connector 6-way IDC connector Powered from the PC USB port (5V) Power switch to control supply to the target Ribbon cable to connect to the VM800P "Tag_Connect" socket. Use of FTDI devices in life support and/or safety applications is entirely at the user's risk, and the user agrees to defend, indemnify and hold FTDI harmless from any and all damages, claims, suits or expense resulting from such use. VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 2 Clearance No.: FTDI# 387 Ordering Information Part No. VA800A_PROG Description VA800A PROG module, programmer for VM800P Plus module Table 2-1 - Ordering information 2 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Table of Contents 1 Introduction ................................................................................... 1 1.1 Features ........................................................................................................ 1 2 Ordering Information ..................................................................... 2 3 Hardware Description ..................................................................... 4 VA800A PROG module ................................................................................... 4 3.2 Physical Descriptions .................................................................................... 4 3.2.1 Dimensions ............................................................................................... 4 3.2.2 VA800A PROG Connectors .......................................................................... 6 3.2.3 VA800A PROG Components ........................................................................ 7 4 Board Schematics ........................................................................... 8 5 Hardware Setup Guide .................................................................... 9 6 5.1 Power Configuration ..................................................................................... 9 5.2 SPI Interface connection .............................................................................. 9 5.3 Programing the VM800P bootloader .............................................................. 9 Contact Information ..................................................................... 13 Appendix A - References....................................................................................... 14 Appendix B - List of Figures and Tables ................................................................. 15 Appendix C - Revision History ............................................................................... 16 3 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 3 Clearance No.: FTDI# 387 Hardware Description Please refer to section 3.2.2 for connector settings. 3.1 VA800A PROG module Figure 3-1 - VA800A PROG module The VA800A PROG module is designed as an ISP programmer to the VM800P Plus module. The main functions of the VA800A PROG are as follows: programmer for the VM800P Plus module. Interface to the VM800P Plus module using SPI interface. Micro-B USB connector 6-way IDC connector Powered from the PC USB port (5V) Power switch to control supply to the target Ribbon cable to connect to the VM800P "Tag_Connect" socket included. 3.2 Physical Descriptions 3.2.1 Dimensions The VA800A PROG module dimensions is illustrated in Figure 3-2 and Figure 3-3. 4 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 54.10 Clearance No.: FTDI# 387 34.70 19.40 85.60 Figure 3-2 - VA800A PROG module Top view 3.20 82.40 Figure 3-3 - VA800A PROG module Bottom view All dimensions are in mm 5 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 3.2.2 VA800A PROG Connectors Connectors are described in the following sections. CN1- USB Connector This is the interface where the USB signals are routed. This interface is used to connect the VA800A PROG board to the PC. Pin No. Name Type 1 VBUS P VBUS, 5V Power Supply 2 D- IO D Minus 3 D+ IO D Plus 4 ID NA Not Connected 5 GND Table 3-1 - CN1 Pinout P Description Ground CN2- SPI Connector This is the interface where the SPI signals are connected. There are also power and ground pins on this interface. The ISP cable is connected between this interface and the VM800P module ISP connector to program the VM800P board. Pin No. Name Type 1 MISO I Master In Slave Out 2 5V P 5V power supply 3 SCK O SPI Clock 4 MOSI O Master Out Slave In 5 SS O Slave Select P Ground 6 GND Table 3-2 - CN2 Pinout Description CN3- ISP Connector This is the interface where the SPI signals are connected. There are also power and ground pins on this interface. The ISP cable is connected to this interface to program the ATMEGA in this board. Pin No. Name Type Description 1 MISO I Master In Slave Out 2 5V P 5V power supply 3 SCK O SPI Clock 4 MOSI O Master Out Slave In 5 RST# O Reset 6 GND Table 3-3 - CN3 Pinout P Ground 6 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Note: CN2 and CN3 should not be used at the same time. Note: CN3 should not be used by customers. Using CN3 will make the module non-functional. SW1- Power switch The power switch should be in ON position to supply external power to VM800P module. 3.2.3 VA800A PROG Components U1 - FT232RQ This converts the USB signals from the PC to UART TTL signals. U2 - ATMEGA328P This converts the UART signals to SPI signals. LED1 - Green Indicates the status of UART RX. Illuminate when the GPIO line is logic 0. LED2 -Red Indicates the status of UART TX. Illuminate when the GPIO line is logic 0. LED3 -Yellow Indicates the status of power. Illuminate when the 5V power is ON. 7 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 4 Clearance No.: FTDI# 387 Board Schematics Figure 4-1 - VA800A PROG Schematics 8 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 5 Clearance No.: FTDI# 387 Hardware Setup Guide 5.1 Power Configuration The board is powered from the PC. The CN1 USB micro-B connector on the VA800A PROG board should be connected to the PC. 5.2 SPI Interface connection The SPI interface is used to program the VM800P Plus module. The ISP cable shown in Figure 5-1 is connected between the SPI interface on the VA800A-PROG module to the ISP connector on the VM800P module. The black colour connector on the ISP cable is connected to connector CN2 on the VA800A-PROG module and the blue colour connector on the ISP cable is connected to connector CN3 on the VM800P module. The SCK signal on CN2 is connected to the SCK signal on the VM800P board. The MOSI signal on CN2 is connected to the MOSI signal on the VM800P board. The MISO signal on CN2 is connected to the MISO signal on the VM800P board. The SS signal on CN2 is connected to the RST signal on the VM800P board. The 5V signal on CN2 is connected to the 5V signal on the VM800P board. The GND signal on CN2 is connected to the GND signal on the VM800P board. Figure 5-1 - ISP Cable 5.3 Programing the VM800P bootloader The bootloader is programmed to the VM800P in the factory using the VM800P ISP connector. This module is used to program the bootloader to the VM800P module. Steps to program the bootloader to VM800P using Arduino IDE. Open the Arduino IDE Select the Tools->Serial Port->COMxx corresponding to the VA800A_PROG. 9 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Figure 5-2 - Select the Serial Port Select the Tools->Board->Arduino Pro or Pro Mini(5V, 16MHz) w/ATmega328 Figure 5-3 - Select the Board Select the Tools->Programmer->Arduino as ISP 10 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Figure 5-4 - Select the Programmer Click on Tools->Burn Bootloader. Figure 5-5 - Burn Bootloader The status bar will display "Burning bootloader to IO board ( This may take a minute)...". 11 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Figure 5-6 - Burning Bootloader When the bootloader has burned successfully the status message will change to "Done burning bootloader.". Figure 5-7 - Done Burning bootloader 12 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 6 Clearance No.: FTDI# 387 Contact Information Head Office - Glasgow, UK Branch Office - Tigard, Oregon, USA Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 7130 SW Fir Loop Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com Branch Office - Taipei, Taiwan Branch Office - Shanghai, China 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 Room 1103, No. 666 West Huaihai Road, Changning District, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) tw.sales1@ftdichip.com tw.support1@ftdichip.com tw.admin1@ftdichip.com cn.sales@ftdichip.com cn.support@ftdichip.com cn.admin@ftdichip.com Web Site http://www.ftdichip.com/ Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user's risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 13 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Appendix A - References VM800P Datasheet: VM800P Plus board FT800 datasheet: FT800_Embedded_Video_Engine FT800 software programming guide: FT800_Programmer_Guide FT800 sample application notes: AN_246_VM800CB_SampleAPP_Arduino_Introduction http://www.ftdichip.com/Support/Documents/AppNotes/AN_275_FT800_Example_with_Arduino.pdf 14 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Appendix B - List of Figures and Tables List of Figures Figure 3-1 - VA800A PROG module .............................................................................................................. 4 Figure 3-2 - VA800A PROG module Top view ............................................................................................... 5 Figure 3-3 - VA800A PROG module Bottom view ......................................................................................... 5 Figure 4-1 - VA800A PROG Schematics ........................................................................................................ 8 Figure 5-1 - ISP Cable ..................................................................................................................................... 9 Figure 5-2 - Select the Serial Port ............................................................................................................... 10 Figure 5-3 - Select the Board ....................................................................................................................... 10 Figure 5-4 - Select the Programmer ............................................................................................................ 11 Figure 5-5 - Burn Bootloader ....................................................................................................................... 11 Figure 5-6 - Burning Bootloader .................................................................................................................. 12 Figure 5-7 - Done Burning bootloader ........................................................................................................ 12 List of Tables Table 2-1 - Ordering information ................................................................................................................... 2 Table 3-1 - CN1 Pinout .................................................................................................................................... 6 Table 3-2 - CN2 Pinout .................................................................................................................................... 6 Table 3-3 - CN3 Pinout .................................................................................................................................... 6 15 Copyright (c) 2014 Future Technology Devices International Limited VA800A_PROG Datasheet Version 1.0 Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Appendix C - Revision History Document Title: DS_VA800A_PROG Document Reference No.: FT_001029 Clearance No.: FTDI# 387 Product Page: http://www.ftdichip.com/EVE.htm Document Feedback: Send Feedback Version 1.0 Initial Datasheet released 14/05/14 16 Copyright (c) 2014 Future Technology Devices International Limited