96 MHz SAW Filter 20 MHz Bandwidth Part Number: SF0096BA02458S DESCRIPTION * * * 96 MHz SAW bandpass filter with 20 MHz bandwidth. 5 x 7 mm SMP. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from Top: Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : Group Delay Deviation : S11 10 10 1 5 100 MHz/div dB/div dB/div deg/div ns/div S22 Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0096BA02458S Rev A ECN 36650 22-Feb-2010 Page 1 of 3 96 MHz SAW Filter 20 MHz Bandwidth Part Number: SF0096BA02458S SPECIFICATION Parameter Center Frequency, FC 1 Insertion Loss (86-106 MHz) 1,2 1 dB Bandwidth Relative Attenuation to Ins Loss (0.3-68.4 MHz) 1,3 Relative Attenuation to Ins Loss (at 76.8 MHz) 1,3 Relative Attenuation to Ins Loss (123.6 to 162.8 MHz) 1,3 Relative Attenuation to Ins Loss (162.8 to 240 MHz) 1,3 Relative Attenuation to Ins Loss (240 to 1000 MHz) 1,3 Amplitude Ripple (86 to 106 MHz) 1,4 Group Delay Ripple (86 to 106 MHz) 1,5 1 dB Compression Point (86 to 106 MHz) Input IP3 6 Temperature Coefficient Source/Load Impedance Ambient Temperature Notes: 1. 2. 3. 4. 5. 6. Min 20.0 50 45 40 35 25 - Typ 96.00 11.3 23.4 55 50 48 53 35 0.75 50 15 40 94 50 25 12 35 - Max 13 1 60 - Units MHz dB MHz dB dB dB dB dB dB p-p ns/div dBm dBm ppm/C ohms C Measured with terminating impedance matched to 50 and with 50 analyzer. Average Insertion Loss in indicated frequency range. Measured as attenuation below the insertion loss point (Insertion loss is reference). Amplitude ripple should be measured without smoothing. Group delay ripple may be measured with a smoothing aperture of 250 KHz . By design. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -25 - 85 85 12 Units C C dBm MATCHING CIRCUIT 10 4 Input 50 Single-ended Output 50 Single-ended All others GND Typical component values: Ls1 Lp1 = = 220 270 nH nH Ls2 Rp2 = = 82 680 nH Notes: 1. Recommend use of 2% tolerance matching components. 2. Component values are for reference only and may change depending on board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0096BA02458S Rev A ECN 36650 22-Feb-2010 Page 2 of 3 96 MHz SAW Filter 20 MHz Bandwidth Part Number: SF0096BA02458S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are 0.15 mm except for the overall length and width, which are nominal values. Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating Pad Configuration: Input: 10 Output: 4 Ground: All other pads ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. (c) 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0096BA02458S Rev A ECN 36650 22-Feb-2010 Page 3 of 3