LM3702,LM3703 LM3702/LM3703 Microprocessor Supervisory Circuits with Low Line Output and Manual Reset Literature Number: SNVS147C LM3702/LM3703 Microprocessor Supervisory Circuits with Low Line Output and Manual Reset General Description The LM3702/LM3703 series of microprocessor supervisory circuits provide the maximum flexibility for monitoring power supplies and battery controlled functions in systems without backup batteries. The LM3702/LM3703 series are available in a 9-bump micro SMD package. Built-in features include the following: Reset: Reset is asserted during power-up, power-down, and brownout conditions. RESET is guaranteed down to VCC of 1.0V. Manual Reset Input: An input that asserts reset when pulled low. Low Line Output: This early power failure warning indicator goes low when the supply voltage drops to a value which is 2% higher than the reset threshold voltage. Features No external components required Manual-Reset input RESET (LM3702) or RESET (LM3703) outputs Precision supply voltage monitor Factory programmable Reset Timeout Delay Available in micro SMD package for minimum footprint 0.5% Reset threshold accuracy at room temperature 2% Reset threshold accuracy over temperature extremes n Reset assertion down to 1V VCC (RESET option only) n 28 A VCC supply current n n n n n n n n Applications n n n n Embedded Controllers and Processors Intelligent Instruments Automotive Systems Critical P Power Monitoring n Standard Reset Threshold voltage: 3.08V n Custom Reset Threshold voltages: For other voltages between 2.2V and 5.0V in 10mV increments, contact National Semiconductor Corp. Typical Application 20011503 (c) 2003 National Semiconductor Corporation DS200115 www.national.com LM3702/LM3703 Microprocessor Supervisory Circuits with Low Line Output and Manual Reset September 2003 LM3702/LM3703 Connection Diagram Top View (looking from the coating side) micro SMD 9 Bump Package BPA09 20011501 Pin Descriptions Bump No. Name Function A1 MR Manual-Reset input. When MR is less than VMRT (Manual Reset Threshold) RESET/RESET is engaged. B1 VCC Power Supply input. C1 RESET Reset Logic Output. Pulses low for tRP (Reset Timeout Period) when triggered, and stays low whenever VCC is below the reset threshold or when MR is below VMRT. It remains low for tRP after either VCC rises above the reset threshold, or after MR input rises above VMRT (LM3702 only). RESET Reset Logic Output. RESET is the inverse of RESET (LM3703 only). C3 LLO Low-Line Logic Output. Early Power-Fail warning output. Low when VCC falls below VLLOT (Low-Line Output Threshold). This output can be used to generate an NMI (Non-Maskable Interrupt) to provide an early warning of imminent power-failure. B3 GND Ground reference for all signals. A2, A3, C2 NC No Connect. B2 NC No Connect. Test input used at factory only. Leave floating. www.national.com 2 LM3702/LM3703 Block Diagram 20011505 3 www.national.com LM3702/LM3703 Ordering Information 20011504 *For other voltages between 2.2V and 5.0V, please contact National Semiconductor sales office. LM3702/LM3703 Output Reset Timeout Period Package Marking LM3702XCBP-308 totem-pole 200ms %%I2 LM3702XCBPX-308 totem-pole 200ms %%I2 LM3703XCBP-308 totem-pole 200ms %%I3 LM3703XCBPX-308 totem-pole 200ms %%I3 LM3703XDBP-308 totem-pole 1600ms %%124 LM3703XDBPX-308 totem-pole 1600ms %%124 LM3702YABP-308 open-drain 1.4ms %%131 LM3702ABPX-308 open-drain 1.4ms %%131 LM3702YDBP-220 open-drain 1600ms %%125 LM3702YDBPX-220 open-drain 1600ms %%125 Part Number %% is the datecode and will vary with time. Table Of Functions Part Number LM3702 Active Low Reset Active High Reset x LM3703 x Output (X = totem-pole) (Y = open-drain) Manual Reset Low Line Output X, Y* Customized x x X Customized x x * = available upon request. Contact National www.national.com Reset Timeout Period 4 (Note 1) Power Dissipation If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Operating Ratings (Note 1) -0.3V to 6.0V All Other Inputs (Note 3) -40C TJ 85C Temperature Range -0.3V to VCC + 0.3V ESD Ratings (Note 2) Human Body Model Machine Model 1.5kV 150V LM3702/LM3703 Series Electrical Characteristics Limits in the standard typeface are for TJ = 25C and limits in boldface type apply over full operating range. Unless otherwise specified: VCC = +2.2V to 5.5V. Symbol Parameter Conditions Min Typ Max Units POWER SUPPLY VCC ICC Operating Voltage Range: VCC LM3702 1.0 5.5 LM3703 1.2 5.5 VCC Supply Current All inputs = VCC; all outputs floating V 28 50 A VRST +0.5 +2 % RESET THRESHOLD VRST Reset Threshold VCC falling -0.5 -2 VCC falling: TA = 0C to 70C VRSTH tRP tRD -1.5 +1.5 0.0032 * VRST Reset Threshold Hysteresis Reset Timeout Period Reset Reset Reset Reset Timeout Timeout Timeout Timeout Period Period Period Period VCC to Reset Delay VCC falling at 1mV/s = = = = A B C D 1 20 140 1120 1.4 28 200 1600 mV 2 40 280 2240 20 ms s RESET (LM3703) VOL VOH RESET RESET VCC > 2.25V, ISINK = 900A 0.3 VCC > 2.7V, ISINK = 1.2mA 0.3 VCC > 4.5V, ISINK = 3.2mA 0.4 VCC > 1.2V, ISOURCE = 50A 0.8 VCC VCC > 1.8V, ISOURCE = 150A 0.8 VCC VCC > 2.25V, ISOURCE = 300A 0.8 VCC VCC VCC ILKG Output Leakage Current > 2.7V, ISOURCE = 500A > 4.5V, ISOURCE = 800A V V 0.8 VCC VCC - 1.5V VRESET = 5.5V 1.0 A RESET (LM3702) VOL RESET VCC > 1.0V, ISINK = 50A 0.3 VCC > 1.2V, ISINK = 100A 0.3 VCC > 2.25V, ISINK = 900A 0.3 VCC VCC VOH RESET VCC VCC VCC > > > > > 2.7V, ISINK = 1.2mA 0.3 4.5V, ISINK = 3.2mA 0.4 2.25V, ISOURCE = 300A 0.8 VCC 2.7V, ISOURCE = 500A 0.8 VCC 4.5V, ISOURCE = 800A VCC - 1.5V 5 V www.national.com LM3702/LM3703 Absolute Maximum Ratings LM3702/LM3703 LM3702/LM3703 Series Electrical Characteristics (Continued) Limits in the standard typeface are for TJ = 25C and limits in boldface type apply over full operating range. Unless otherwise specified: VCC = +2.2V to 5.5V. Symbol Parameter Conditions Min Typ Max Units MR VMRT VMRTH MR Input Threshold MR Threshold Hysteresis RMR MR Pull-up Resistance tMD MR to Reset Delay tMR MR Pulse Width MR, Low 0.8 MR, High MR falling: VCC = VRST 2.0 MAX 0.0032 * VRST to 5.5V 35 56 V mV 75 12 k S 25 S LLO VOL LLO Output Voltage VOH VCC > 2.25V, ISINK = 900A 0.3 VCC > 2.7V, ISINK = 1.2mA 0.3 VCC > 4.5V, ISINK = 3.2mA 0.4 VCC VCC VCC > 2.25V, ISOURCE = 300A > 2.7V, ISOURCE = 500A > 4.5V, ISOURCE = 800A 0.8 VCC V 0.8 VCC VCC - 1.5V LLO OUTPUT VLLOT LLO Output Threshold (VLLO - VRST, VCC falling) VLLOTH Low-Line Comparator Hysteresis tCD Low-Line Comparator Delay 1.01 * VRST VCC falling at 1mV/s 1.02 * VRST 1.03 * VRST V 0.0032 * VRST mV 20 s Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed conditions. Note 2: The Human Body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, J-A, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperture is calculated using: Where the value of J-A for the micro SMD package is 220C/W. www.national.com 6 Supply Current vs Supply Voltage 3.3V Supply Current vs Temperature 20011511 20011515 Normalized Reset Threshold Voltage vs Temperature Reset Timeout Period vs VCC 20011512 20011532 Max. Transient Duration vs Reset Comparator Overdrive (VCC = 3.3V) Reset Timeout Period vs Temperature 20011510 20011516 7 www.national.com LM3702/LM3703 Typical Performance Characteristics LM3702/LM3703 Typical Performance Characteristics (Continued) Low-Line Comparator Propagation Delay vs Temperature 20011514 www.national.com 8 RESET OUTPUT The Reset input of a P initializes the device into a known state. The LM3702/LM3703 microprocessor supervisory circuits assert a forced reset output to prevent code execution errors during power-up, power-down, and brownout conditions. RESET is guaranteed valid for VCC > 1V. Once VCC exceeds the reset threshold, an internal timer maintains the output for the reset timeout period. After this interval, reset goes high. The LM3702 offers an active-low RESET; The LM3703 offers an active-high RESET. LOW-LINE OUTPUT (LLO) The low-line output comparator is typically used to provide a non-maskable interrupt to a P when VCC begins falling. LLO monitors VCC and goes low when VCC falls below VLLOT (typically 1.02 * VRST) with hysteresis of 0.0032 * VRST. SPECIAL PRECAUTIONS FOR THE MICRO SMD PACKAGE As with most integrated circuits, the LM3702 and LM3703 are sensitive to exposure from visible and infrared (IR) light radiation. Unlike a plastic encapsulated IC, the micro SMD package has very limited shielding from light, and some sensitivity to light reflected from the surface of the PC board or long wavelength IR entering the die from the side may be experienced. This light could have an unpredictable affect on the electrical performance of the IC. Care should be taken to shield the device from direct exposure to bright visible or IR light during operation. Any time VCC drops below the reset threshold (such as during a brownout), the reset activates. When VCC again rises above the reset threshold, the internal timer starts. Reset holds until VCC exceeds the reset threshold for longer than the reset timeout period. After this time, reset releases. The Manual Reset input (MR) will initiate a forced reset also. See the Manual Reset Input section. RESET THRESHOLD The LM3702/LM3703 family is available with a reset voltage of 3.08V. Other reset thresholds in the 2.20V to 5.0V range, in steps of 10 mV, are available; contact National Semiconductor for details. MICRO SMD MOUNTING The micro SMD package requires specific mounting techniques which are detailed in National Semiconductor Application Note AN-1112. Referring to the section Surface Mount Technology (SMT) Assembly Considerations, it should be noted that the pad style which must be used with the 9-pin package is the NSMD (non-solder mask defined) type. MANUAL RESET INPUT (MR) Many P-based products require a manual reset capability, allowing the operator to initiate a reset. The MR input is fully debounced and provides an internal 56 k pull-up. When the MR input is pulled below VMRT (1.225V) for more than 25 s, reset is asserted after a typical delay of 12 s. Reset remains active as long as MR is held low, and releases after the reset For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the micro SMD device. 9 www.national.com LM3702/LM3703 timeout period expires after MR rises above VMRT. Use MR with digital logic to assert or to daisy chain supervisory circuits. It may be used as another low-line comparator by adding a buffer. Circuit Information LM3702/LM3703 Timing Diagrams 20011528 FIGURE 1. LM3702 Reset Time with MR 20011529 FIGURE 2. LLO Output www.national.com 10 LM3702/LM3703 Typical Application Circuits 20011524 FIGURE 3. LM3703 Power-On Delay 11 www.national.com LM3702/LM3703 Typical Application Circuits (Continued) 20011522 FIGURE 4. Regulator/Switch with Long-Term Overvoltage Lockout Prevents Overdissipation in Linear Regulator 20011531 FIGURE 5. Switch Debouncer www.national.com 12 inches (millimeters) NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN 1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTER CLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6.NO JEDEC REGISTRATION AS OF AUG.1999. 9 bump micro SMD Package NS Package Number BPA09FFB The dimensions of X1, X2 and X3 are given below X1 = 1.412mm X2 = 1.412mm X3 = 0.850mm LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM3702/LM3703 Microprocessor Supervisory Circuits with Low Line Output and Manual Reset Physical Dimensions unless otherwise noted IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated