ALUMINUM ELECTROLYTIC CAPACITORS UB Chip Type, High Reliability series (Through 50V only) Chip type, high temperature range, for +125C use. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). WH High Temperature Reflow Added ESR specification at - 40C CJ High Temperature UB UX Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Performance Characteristics - 40 to +125C 10 to 400V 1 to 330F 20% at 120Hz, 20C Leakage Current Rated voltage (V) 10 to 50 160 to 400 Leakage Current After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (A). I = 0.04CV+100 ( A) max.(1 minute's) Measurement frequency : 120Hz, Temperature : 20C Tangent of loss angle (tan ) 10 0.32 Rated voltage (V) tan (MAX.) 16 0.24 25 0.21 35 0.18 50 0.18 160 0.30 200 0.30 250 0.30 400 0.30 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) 10 16 25 35 50 160 200 250 400 Impedance ratio Z- 40C / Z+20C ZT / Z20 (MAX.) 12 8 6 4 4 8 8 8 12 After storing the capacitors under no load at 125C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Capacitance change Within 10% of the initial capacitance value which is maintained at 250C. The capacitors shall meet tan Less than or equal to the initial specified value the characteristic requirements listed at right when they Leakage current Less than or equal to the initial specified value are removed from the plate and restored to 20C. Black print on the case top. Shelf Life Resistance to soldering heat Marking Chip Type Type numbering system (Example : 10V 100F) (8 x 6.2) 1 3 4 5 6 7 8 9 10 11 12 13 14 A0.2 C0.2 Taping code Capacitance tolerance (20%) Configuration E B0.2 A2E 100 10V D0.5 Voltage Capacitance Lot No. 2 UUB 1 A 1 0 1 MCL 1 GS A0.2 Plastic platform 0.3MAX. 0.5MAX. Positive 125C Marking Trade mark Within 30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value Capacitance change tan Leakage current The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours (1000 hours for 8 x 6.2) at 125C. Endurance L0.3 D x L Rated capacitance (100F) 8 x 6.2 8 x 10 Rated voltage (10V) 10 x 10 Negative H 1 1.8 2.2 3.3 4.7 6.8 10 H 10 1A 100 220 330 470 101 221 331 V Cap.(F) Negative V Code 010 022 033 047 100 220 330 Code 010 1R8 2R2 3R3 4R7 6R8 100 8 x 6.2 8 x 10 10 x 10 160 2C 8 x 10 10 x 10 D x L A B C E L H A0.2 E B0.2 D0.5 L0.5 Pressure relief vent Cap.(F) Type (mm) A0.2 C0.2 Voltage Dimensions Series name Positive Plastic platform 0.3MAX. Capacitance A2E 330 10V 125C Marking Lot No. Trade mark 0.5MAX. (8 x 10, 10 x 10) 8 x 10 10 x 10 200 2D 42 59 8 x 6.2 8 x 10 3.3 2.9 8.3 8.3 8.3 8.3 2.3 3.1 6.2 10 0.5 to 0.8 0.8 to 1.1 16 1C 58 90 112 8 x 10 10 x 10 10 x 10 66 102 8 x 10 10 x 10 10 x 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 25 1E 250 2E 36 59 59 Code CL NL NL 28 59 8 x 6.2 8 x 10 10 x 10 400 2G 8 x 10 8 x 10 10 x 10 10 x 10 26 27 36 38 Rated ripple current (mArms) at 125C 120Hz 35 1V 48 74 116 8 x 6.2 8 x 10 10 x 10 44 52 80 8 x 6.2 8 x 6.2 8 x 10 10 x 10 50 1H Case size D x L (mm) 24 38 46 58 Rated ripple Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UH(p.116) series if high CV products are required. Please refer to page 3 for the minimum order quantity. CAT.8100A