LD39015 150 mA low quiescent current and low noise voltage regulator Datasheet - production data * Compatible with ceramic capacitors CO = 1 F * Internal current and thermal limit * Temperature range: -40 C to 125 C Description SOT23-5L Features * Input voltage from 1.5 to 5.5 V * Ultra low-dropout voltage (80 mV typ. at 100 mA load) * Very low quiescent current (18 A typ. at no load, 38 A typ. at 150 mA load, 1 A max. in OFF mode) * Very low noise without bypass capacitor (29 VRMS at VOUT = 0.8 V) * Output voltage tolerance: 2.0% @ 25 C The LD39015 series provides 150 mA maximum current with an input voltage range from 1.5 V to 5.5 V and a typical dropout voltage of 80 mV. It is stable with ceramic capacitors. The ultra low drop voltage, low quiescent current and low noise features make it suitable for low power batterypowered applications. Power supply rejection is 65 dB at low frequencies and starts rolling off at 10 kHz. Enable logic control function puts the LD39015 in shutdown mode allowing a total current consumption lower than 1 A. The device also includes short-circuit constant current limiting and thermal protection. Typical applications are mobile phones, personal digital assistants (PDAs), cordless phones or similar batterypowered systems. * 150 mA guaranteed output current * Wide range of output voltages available on request: 0.8 V to 3.3 V with 100 mV step * Logic-controlled electronic shutdown Table 1. Device summary Order codes Output voltages LD39015M08R 0.8 V LD39015M10R 1.0 V LD39015M12R 1.2 V LD39015M125R 1.25 V LD39015M15R 1.5 V LD39015M18R 1.8 V LD39015M25R 2.5 V LD39015M33R 3.3 V July 2015 This is information on a product in full production. DocID14003 Rev 5 1/15 www.st.com Contents LD39015 Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 2/15 7.1 SOT23-5L package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 7.2 SOT23-5L packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DocID14003 Rev 5 LD39015 1 Diagram Diagram Figure 1. Block diagram OUT IN BandGap 1.22 V R1 Trimming Thermal Protection R2 Enable EN GND DocID14003 Rev 5 3/15 15 Pin configuration 2 LD39015 Pin configuration Figure 2. Pin connection (top view) SOT23-5L Table 2. Pin description 4/15 Pin n Symbol Function 1 IN LDO input voltage 2 GND Common ground 3 EN Enable pin logic input: low = shutdown, high = active 4 NC Not connected 5 OUT Output voltage DocID14003 Rev 5 LD39015 3 Typical application Typical application Figure 3. Typical application circuit 9,1 ,1 ) 9(1 9287 287 ) (1 /RDG *1' DocID14003 Rev 5 5/15 15 Maximum ratings 4 LD39015 Maximum ratings Table 3. Absolute maximum ratings Symbol VIN Parameter DC input voltage Value Unit -0.3 to 7 V VOUT DC output voltage - 0.3 to VI + 0.3 V VEN Enable input voltage - 0.3 to VI + 0.3 V IOUT Output current Internally limited mA Power dissipation Internally limited mW PD TSTG Storage temperature range -65 to 150 C TOP Operating junction temperature range -40 to 125 C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. All values are referred to GND. Table 4. Thermal data Symbol 6/15 Parameter SOT23-5L Unit RthJA Thermal resistance junction-ambient 255 C/W RthJC Thermal resistance junction-case 81 C/W DocID14003 Rev 5 LD39015 5 Electrical characteristics Electrical characteristics TJ = 25 C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 F, IOUT = 1 mA, VEN = VIN, unless otherwise specified. Table 5. Electrical characteristics (1) Symbol VIN Parameter Test conditions Operating input voltage Min. 1.5 Turn-on threshold VUVLO VOUT 1.45 Turn-off threshold VOUT accuracy Typ. 1.30 VOUT > 1.5 V, IOUT = 1 mA TJ = 25 C -2.0 VOUT > 1.5 V, IOUT = 1 mA -40 C < TJ < 125 C -3.0 Max. Unit 5.5 V 1.48 V 1.35 mV 2.0 % 3.0 VOUT 1.5 V, IOUT = 1 mA 10 VOUT 1.5 V, IOUT = 1 mA -40 C < TJ < 125 C 30 0.01 %/V 10 mVpp mV VOUT Static line regulation VOUT +1 V VIN 5.5 V IOUT = 1 mA VOUT Transient line regulation (2) VIN = + 500 mV, IOUT = 1 mA TR = TF = 5 s VOUT Static load regulation IOUT = 1 mA to 150 mA 0.002 %/mA VOUT Transient load regulation (2) IOUT = 1 mA to 150 mA TR = TF = 5 s 40 mVpp VDROP Dropout voltage (3) IOUT = 100 mA, VOUT > 1.5 V -40 C < TJ < 125 C 80 Output noise voltage 1.1 kHz to 100 kHz, IOUT = 10 mA VOUT = 0.8 V 29 VIN = VOUTNOM + 0.5 V +/-VRIPPLE VRIPPLE = 0.1 V, freq. = 1 kHz IOUT = 10 mA 65 VIN = VOUTNOM + 0.5 V +/-VRIPPLE VRIPPLE = 0.1 V, freq.=10 kHz IOUT = 10 mA 62 IOUT = 0 mA 18 eN SVR Supply voltage rejection VOUT = 1.5 V IOUT = 0 to 150 mA Quiescent current DocID14003 Rev 5 VRMS 50 38 A IOUT = 0 to 150 mA -40 C < TJ< 125 C VIN input current in OFF mode: VEN = GND mV dB IOUT = 0 mA, -40 C < TJ < 125 C IQ 100 70 0.001 1 7/15 15 Electrical characteristics LD39015 Table 5. Electrical characteristics (continued)(1) Symbol ISC Parameter Short-circuit current RL = 0 Enable input logic low VIN = 1.5 V to 5.5 V -40 C < TJ < 125 C Enable input logic high VIN = 1.5 V to 5.5 V -40 C < TJ < 125 C Enable pin input current VEN = VIN VEN IEN TON TSHDN COUT Test conditions Turn-on time Min. Typ. Max. 350 mA 0.4 0.9 V V 0.1 (4) Unit 100 30 Thermal shutdown 160 Hysteresis 20 nA s C Output capacitor Capacitance (see typical performance characteristics for stability) 1 22 F 1. For VOUT(NOM) < 1.2 V, VIN = 1.5 V 2. All transient values are guaranteed by design, not production tested 3. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This specification does not apply to output voltages below 1.5 V 4. Turn-on time is the time measured between the enable input just exceeding VEN high value and the output voltage just reaching 95% of its nominal value 8/15 DocID14003 Rev 5 LD39015 Typical performance characteristics 6 Typical performance characteristics 0.85 0.84 0.83 0.82 0.81 0.8 0.79 0.78 0.77 0.76 0.75 -50 Figure 5. Output voltage vs. input voltage IOUT=1mA IOUT=100mA 9287>9@ VOUT [V] Figure 4. Output voltage vs. temperature VIN=1.5V 0 50 100 150 2.4 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0.1 0.15 0.2 IOUT=1 mA to 0.15 A 1.8 1.5 1.2 STABILITY REGION 0.9 0.6 0.3 0 0.25 0 Figure 8. Supply voltage rejection vs. frequency 5 10 15 20 COUT [F] (nominal value) 25 Figure 9. Output noise voltage vs. frequency 800 IOUT=10 mA, VIN=4.3 V, CIN=COUT= 1F 700 VOUT=3.3 V 600 500 nV/Hz SVR [dB] CIN=1 F, VIN=VEN=1.5 to 5.5 V 2.1 IOUT [A] 75 70 65 60 55 50 45 40 35 30 25 20 15 10 100 Figure 7. COUT stability region ESR @ 100 KHz [Ohm] Vdropout [V] Figure 6. Dropout voltage vs. output current 0.05 9,1 >9@ Temp [C] 0 400 300 200 IOUT = 10mA Vripple = 0.1Vpp 100 1000 10000 100000 0 1000 Freq [Hz] 10000 100000 FREQ [Hz] DocID14003 Rev 5 9/15 15 Typical performance characteristics LD39015 Figure 10. Quiescent current vs. input voltage Figure 11. Load transient 100 Iq [A] 80 60 40 20 VIN=VINH, CIN=COUT=1F, IOUT=0.15A 0 1.4 1.9 2.4 2.9 3.4 3.9 4.4 4.9 5.4 5.9 VIN[V] VEN = VIN = 1.5V, IOUT = 1mA to 0.15A, CIN = COUT = 1F, tr = tf = 5s Figure 12. Line transient VIN = VEN = 1.5 to 5.5V, IOUT = 1mA, COUT = 1F, tr = tf = 5s 10/15 Figure 13. Enable transient VIN = 1.5V, VEN = 0 to 1V, IOUT = 1mA, CIN = COUT = 1F DocID14003 Rev 5 LD39015 7 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 7.1 SOT23-5L package information Figure 14. SOT23-5L package outline BN DocID14003 Rev 5 11/15 15 Package information LD39015 Table 6. SOT23-5L mechanical data mm Dim. Min. Typ. Max. A 0.90 1.45 A1 0 0.15 A2 0.90 1.30 b 0.30 0.50 c 0.09 0.20 D 2.95 E 1.60 e 0.95 H 2.80 L 0.30 0.60 q 0 8 Figure 15. SOT23-5L recommended footprint (dimensions in mm) BN 12/15 DocID14003 Rev 5 LD39015 7.2 Package information SOT23-5L packing information Figure 16. SOT23-5L tape and reel outline Table 7. SOT23-5L tape and reel mechanical data mm Dim. Min. Typ. A Max. 180 C 12.8 D 20.2 N 60 13.0 T 13.2 14.4 Ao 3.13 3.23 3.33 Bo 3.07 3.17 3.27 Ko 1.27 1.37 1.47 Po 3.9 4.0 4.1 P 3.9 4.0 4.1 DocID14003 Rev 5 13/15 15 Revision history 8 LD39015 Revision history Table 8. Document revision history Date Revision 13-Nov-2007 1 Initial release. 11-Apr-2008 2 Modified: Table 5 on page 7. 12-Feb-2009 3 Modified: Table 1 on page 1. 4 Part number LD39015xx changed to LD39015. Updated the Description in cover page and Section 7: Package information. Added Section 7.2: SOT23-5L packing information. Minor text changes. 5 Removed SOT666 package. Updated features in cover page, Table 1: Device summary, Table 2: Pin description, Table 4: Thermal data, Figure 2: Pin connection (top view) and Section 7: Package information. Minor text changes. 11-Feb-2014 07-Jul-2015 14/15 Changes DocID14003 Rev 5 LD39015 IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2015 STMicroelectronics - All rights reserved DocID14003 Rev 5 15/15 15