HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Typical Applications Features The HMC799LP3E is ideal for: 10 kOhm Transimpedance * Laser Sensor Very Low Noise: 150nA Input RMS Noise over 700 MHz Bandwidth * FDDI Receiver 700 MHz Analog Bandwidth * CATV FM Analog Receiver Wide Dynamic Range: +65 dB * Wideband Gain Block Low Power: 70mA from Single +5V Supply * Low Noise RF Applications 16 Lead 3x3 mm SMT Package: 9mm General Description Functional Diagram The HMC799LP3E is DC to 700 MHz Transimpedance amplifier designed for opto-electronic laser sensor applications, FDDI receivers and receiver systems employing optical to electrical conversion. This amplifier provides a single-ended output voltage that is proportional to an applied current at its input port. This current is typically provided by a photodiode. Operating from a single +5V supply, HMC799LP3E features very low input referred noise, and very large electrical input dynamic range exceeding 65 dB. 10 kOhm or 80 dB-Ohms transimpedance gain provides very good sensitivity at higher data rates. The output of HMC799LP3E is internally matched to 50 ohms. External matching is not necessary. The HMC799LP3E exhibits excellent gain and output power stability over temperature, while requiring a minimal number of external bias components. TRANSIMPEDANCE amps - smt 11 11 - 1 Electrical Specifications, TA = +25 C, Vcc1 = Vcc2 = Vcc3 = +5V Parameter Conditions Min. Typ. Max. Units 4.5 5 5.5 V 70 80 DC Specifications Power Supply Voltage Power Supply Current Vcc = 5V Input Impedance 60 @ 350 MHz Input Bias Voltage mA 175 Ohm 2.1 V AC Specifications Transimpedance @ 100 MHz, RL = 50 Ohm Transimpedance 3-dB Bandwidth Small Signal Gain S21 Cpd Input Referred Current Noise Density [1] 7.5 10 600 700 12.5 k Ohms MHz 42 dB <1pF, @ 200 MHz 4.6 pA / Hz Cpd [1] = 1pF, @ 200 MHz 4.8 pA / Hz Cpd [1] = 2pF, @ 200 MHz 5.2 pA / Hz 5.6 pA / Hz Cpd [1] = 3pF, @ 200 MHz [1] Cpd is the total parasitic capacitance value arises from addition of input photo diode. This value includes photo diode parasitic capacitance, PCB trace capacitance and package parasitic capacitance. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Electrical Specifications (Conditions) Parameter Conditions Input Referred RMS Current Noise Min. Typ. Max. Units Cpd [1] <1pF, @ 700 MHz BW 149 Cpd [1] = 1pF, @630 MHz BW 164 nA RMS Cpd [1] = 2pF, @ 560 MHz BW 174 nA RMS Cpd [1] = 3pF, @ 420 MHz BW 132 nA RMS Vp-p Saturated Output Swing nA RMS Vin = 50mV p-p 1 Output Power 1-dB Compression OP1dB @ 200 MHz 4 dBm Output Third Order Intercept Point OIP3 @ 200 MHz 13 dBm 20 mA 20 dB Input Overdrive Current Output Return Loss @ 500 MHz Output Return Loss vs. Temperature 0 40 -10 30 +25C +85C -40C 20 10 +25C +85C -40C 11 -20 -30 -40 0 -50 200 300 400 500 600 FREQUENCY (MHz) 700 800 0 100 200 300 400 500 600 Input Referred Noise Density vs. CPD [1] Input Referred Noise Density vs. Temperature [2] 20 C =0pF pd C =1pF 15 pd C =2pF pd C =3pF pd 10 5 0 0 100 200 300 400 500 600 FREQUENCY (MHz) 700 800 700 800 FREQUENCY (MHz) INPUT REFERRED NOISE DENSITY (pA/Hz) 100 INPUT REFERRED NOISE DENSITY (pA/Hz) 0 700 800 20 +25C +85C -40C 15 10 5 0 0 100 200 300 400 500 600 FREQUENCY (MHz) [1] Cpd is the total parasitic capacitance value resulting from the addition of the input photo diode. This value includes photo diode parasitic capacitance, PCB trace capacitance and package parasitic capacitance. [2] Cpd = 1 pF Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com TRANSIMPEDANCE amps - smt 50 RETURN LOSS (dB) GAIN (dB) Gain vs. Temperature 16 11 - 2 HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Transimpedance vs. CPD Transimpedance vs. Supply Voltage (Vcc) [2] [1] 20 C =0pF pd TRANSIMPEDANCE (kOhm) TRANSIMPEDANCE (kOhm) 20 C =1pF pd 15 C =2pF pd C =3pF pd 10 5 0 Vcc=4.5V Vcc=5.0V Vcc=5.5V 15 10 5 0 0 100 200 300 400 500 600 700 800 0 100 FREQUENCY (MHz) 500 600 700 800 10 OUTPUT POWER (dBm) TRANSIMPEDANCE (kOhm) TRANSIMPEDANCE amps - smt 400 Output Power vs. Input Power @ 200 MHz [2] [2] 20 11 - 3 300 FREQUENCY (MHz) Transimpedance vs. Temperature 11 200 15 10 +25C +85C -40C 5 0 0 100 200 300 400 500 FREQUENCY (MHz) 600 700 800 5 0 -5 -10 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) [1] Cpd is the total parasitic capacitance value resulting from the addition of the input photo diode. This value includes photo diode parasitic capacitance, PCB trace capacitance and package parasitic capacitance. [2] Cpd = 1 pF Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Output Signal [1] Measurements Current Mean std dev Min. Max 212.70 V amptd 198.84 200.50 3.6253 184.99 Frequency 200.8 199.9 0.631 198.0 Duty Cycle 50.9 49.7 0.62 47.6 Units mV 202.1 MHz 51.6 % [1] Input signal current 25 Ap-p, frequency 200 MHz Output Signal [2] Measurements Current Mean Min. Max V amptd 959.62 960.47 std dev 3.703 953.11 972.63 Frequency 200.1 200.0 0.117 199.5 Duty Cycle 49.1 49 0.08 48.7 Units mV 200.4 MHz 49.2 % 11 TRANSIMPEDANCE amps - smt [2] Input signal current 20 mAp-p, frequency 200 MHz Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com 11 - 4 HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Absolute Maximum Ratings Power Supply Voltage (Vcc1, Vcc2, Vcc3) -1V to 8V Input Current 30 mAp-p Junction Temperature 125 C Continuous Pdiss (T=85 C) (derate 31.82 mW/ C Above +85 C 1.27W Thermal Resistance (Junction to ground paddle) 31.43 C/W Storage Temperature -65 to 125 C Operating Temperature -40 to +85 C ESD Sensitivity (HBM) Class 1C Outline Drawing TRANSIMPEDANCE amps - smt 11 11 - 5 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HMC APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC799LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H799 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 C Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Pin Descriptions Pin Number Function Description 1, 12, 14 VCC1, VCC2, VCC3 Positive Supply 2 CFILT Overload current filter capacitance pin. 3 RFIN RF Input 4 CEXT Reference voltage filter capacitance pin. Interface Schematic N/C Not connected. 10 RFOUT RF Output Package Base GND Package base has exposed metal ground paddle which must be connected to ground. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com TRANSIMPEDANCE amps - smt 11 5 - 9, 11, 13, 15, 16 11 - 6 HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Application Circuit TRANSIMPEDANCE amps - smt 11 11 - 7 Note: For power supply rejection ratio (PSRR) tests, install 0 Ohm for R1. Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com HMC799LP3E v01.1009 DC - 700 MHz, 10 kOhm TRANSIMPEDANCE AMPLIFIER Evaluation PCB List of Materials for Evaluation PCB 124022 [1] Item Description J1 - J2 PCB Mount SMA Connector J3, J5 DC Pin C1 - C3 22 nF Capacitor, 0402 Pkg. C4, C12 10 F Capacitor, 0805 Pkg. C6, C8, C10 4.7 F Capacitor, 0805 Pkg. C7, C9, C11 0.1 F Capacitor, 0603 Pkg. U1 HMC799LP3E Transimpedance Amplifier PCB [2] 124020 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 Information furnished by Analog Devices is believed to be accurate and reliable. However, no For price, 20 delivery, and to place orders: Analog For price, delivery and to place orders: Microwave Corporation, Alpha Road, Chelmsford, MADevices, 01824 Inc., responsibility is assumed by Analog Devices for its use, nor for anyHittite infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 rights of third parties that may result from its use. Specifications subject to change without notice. No Phone: 978-250-3343 Fax: 978-250-3373 Order at www.hittite.com Phone: On-line 781-329-4700 * Order online at www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Application Support: Phone: 1-800-ANALOG-D Trademarks and registered trademarks are the property of their respective owners. Application Support: Phone: 978-250-3343 or apps@hittite.com TRANSIMPEDANCE amps - smt 11 11 - 8